OWNER'S OPERATING MANUAL
DTV-992/992 ULTRA
DTV Capable CRT Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY INSTRUCTIONS ................................................................................................................................1-1
On Safety............................................................................................................................................................1-1
On Installation.....................................................................................................................................................1-2
On Servicing .......................................................................................................................................................1-2
On Cleaning........................................................................................................................................................1-2
On Repacking .....................................................................................................................................................1-2
On Illumination....................................................................................................................................................1-2
LOCATION AND FUNCTION OF CONTROLS.....................................................................................2-1
Rear Panel Terminology .....................................................................................................................................2-1
Front Panel Terminology.....................................................................................................................................2-1
Control Panel Terminology..................................................................................................................................2-2
Remote Control Description................................................................................................................................2-3
CONNECTIONS ....................................................................................................................................3-1
AC Power (mains) Cord Connection ..................................................................................................................3-1
Power Check.......................................................................................................................................................3-1
Switching on/off...................................................................................................................................................3-1
Start Up With Full White Image ..........................................................................................................................3-2
Signal Input Connection to the Projector............................................................................................................3-2
Connecting a Composite Video Source to Port 1...............................................................................................3-3
Connecting an S-Video or Video Source to Port 2.............................................................................................3-3
Connecting an RGB Analog Source With Composite Sync ...............................................................................3-4
Connecting an RGB Analog Source With Tri-Level Sync...................................................................................3-4
RGB3S or RG3sB Input Selection ................................................................................................................3-4
Connecting a Component Source.......................................................................................................................3-5
(R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) Input Selection.............................................................................................3-5
Connecting a Component Source With Tri-Level Sync ......................................................................................3-5
(R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) Input Selection .........................................................................................3-6
Connecting a Computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS232 Input of
the Projector........................................................................................................................................................3-6
CONTROLLING ....................................................................................................................................4-1
Battery Installation in the RCU ...........................................................................................................................4-1
How to Use Your RCU........................................................................................................................................4-2
Projector Address ...............................................................................................................................................4-2
How to Display a Projector Address...................................................................................................................4-2
How to Program an Address Into the RCU ........................................................................................................4-2
Input Selection ....................................................................................................................................................4-3
Analog Picture Controls......................................................................................................................................4-4
Brightness Control.........................................................................................................................................4-4
Contrast Control ............................................................................................................................................4-4
Color Saturation Control................................................................................................................................4-4
Tint Control....................................................................................................................................................4-4
Sharpness Control.........................................................................................................................................4-4
The Pause Key ...................................................................................................................................................4-4
START UP OF THE ADJUSTMENT MODE..........................................................................................5-1
i-1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
RANDOM ACCESS ADJUSTMENT MODE..................................................................................................6-1
Starting Up the Random Access Adjustment Mode...............................................................................................6-1
Overview ‘Random Access Adjustment’ Mode ......................................................................................................6-1
Selecting Setup Pattern .........................................................................................................................................6-2
Internal Cross Hatch Pattern..................................................................................................................................6-2
Random Access Adjustment Mode Selection Menu..............................................................................................6-3
Picture Tuning ........................................................................................................................................................6-3
Color Balance.........................................................................................................................................................6-3
Sync Fast/Slow Adjustment ...................................................................................................................................6-3
Peaking ..................................................................................................................................................................6-4
Color Select............................................................................................................................................................6-4
Clamp Tuning.........................................................................................................................................................6-4
Focusing.................................................................................................................................................................6-5
Geometry Adjustments...........................................................................................................................................6-6
Horizontal Phase Adjustment.................................................................................................................................6-6
Raster Shift Adjustment .........................................................................................................................................6-7
Left-Right (east-west) Adjustments........................................................................................................................6-8
Left Side Correction ...............................................................................................................................................6-9
Top-Bottom (north-south) Adjustments ................................................................................................................6-10
Size Adjustment....................................................................................................................................................6-11
Vertical Linearity Adjustment................................................................................................................................6-11
Blanking Adjustments...........................................................................................................................................6-12
Convergence Adjustment.....................................................................................................................................6-13
Vertical Corners....................................................................................................................................................6-14
Fine Convergence Adjustments...........................................................................................................................6-14
SERVICE MODE ...................................................................................................................................7-1
Starting up the Service Mode.................................................................................................................................7-1
Overview flowchart ‘Service’ Mode........................................................................................................................7-1
Identification ...........................................................................................................................................................7-2
Copy a Block..........................................................................................................................................................7-2
Deletion of Blocks ..................................................................................................................................................7-3
Deleting Block by Block .........................................................................................................................................7-3
Deletion of All Blocks .............................................................................................................................................7-3
Change Password..................................................................................................................................................7-4
Change Language..................................................................................................................................................7-4
Total Run Time.......................................................................................................................................................7-4
All settings to Midposition ......................................................................................................................................7-5
Undo All Settings to Midpos...................................................................................................................................7-5
R & B Convergence Mid ........................................................................................................................................7-5
Undo R & B Convergence Mid...............................................................................................................................7-5
Dynamic Astigmatism.............................................................................................................................................7-6
G2 Adjustment .......................................................................................................................................................7-7
CRT Run in Cycle ..................................................................................................................................................7-7
Projector Warm-Up.................................................................................................................................................7-8
MESSAGES, WARNINGS, AND FAILURES........................................................................................8-1
SPECIFICATIONS.................................................................................................................................9-1
APPENDIX 1 (RS 232 Control).......................................................................................................APP-1
i-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Configuration....................................................................................................................................APP-1
How to Format the Control Data.......................................................................................................................APP-1
Sending a RECORD (single instruction)...........................................................................................................APP-2
Example String to Send to the Projector With Address 3 to Turn it On/Off......................................................APP-3
COMMAND CODE LIST...................................................................................................................................APP-3
APPENDIX 2 (EYE-QTM Autoconvergence)....................................................................................APX-1
Overview .........................................................................................................................................APX-1
THE QUICK GUIDE to using the EYE-QTM system .......................................................................APX-1
Easy-To-Use, High Precision Automatic Convergence System .......................................................................APX-2
Easy-To-Use, High Precision Automatic Geometry System.............................................................................APX-2
Compact Built-In System ..................................................................................................................................APX-2
Preparing Your EYE-QTM ...................................................................................................................................APX-2
ON-SCREEN OPERATING INSTRUCTIONS..................................................................................APX-3
ACCESS TO EYE-QTM ON-SCREEN MENUS..................................................................................................APX-3
EYE-QTM MENU.................................................................................................................................................APX-3
EYE-QTM SETUP...............................................................................................................................APX-4
Setting the Configuration ..................................................................................................................................APX-4
FOCUSING THE CAMERA LENS...................................................................................................APX-5
CENTERING THE CAMERA...........................................................................................................APX-6
Centering The Camera Horizontally .................................................................................................................APX-6
Centuring The Camera Vertically......................................................................................................................APX-7
SET TOUCH-UP OPTIONS .............................................................................................................APX-7
Touch-Up On Source On/Off.............................................................................................................................APX-7
Touch-Up On Timer...........................................................................................................................................APX-8
Reference Source.............................................................................................................................................APX-8
Adjusting Other Sources...................................................................................................................................APX-8
Learning A Reference.......................................................................................................................................APX-9
WHAT IS BEING MEASURED BY EYE-QTM.....................................................................................................APX-9
TOUCH UP AND AUTOCONVERGENCE ....................................................................................APX-10
Adjusting Screen Size.....................................................................................................................................APX-10
On Current Source..........................................................................................................................................APX-10
Touch-Up.........................................................................................................................................................APX-11
Align On Current Source.................................................................................................................................APX-11
Align From Midposition On Current Source...................................................................................................APX-11
On All Sources................................................................................................................................................APX-12
Touch-Up On All Sources ...............................................................................................................................APX-12
Align On All Sources.......................................................................................................................................APX-12
i-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Align From Midposition on All Sources...........................................................................................................APX-13
Interrupting the Automatic Convergence Process ..........................................................................................APX-13
Error Messages...............................................................................................................................................APX-13
No Pattern Error..............................................................................................................................................APX-14
Status Reporting Forced Break ......................................................................................................................APX-14
EYE-QTM DIAGNOSTICS................................................................................................................APX-15
i-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Notice on Safety
FEDERAL COMMUNICATION COMMISSION (FCC
STATEMENT)
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
This equipment has been tested and found to comply with the lim-
its of a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful inter-
ference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
These safety standards impose important requirements on the use
of safety critical components, materials and isolation, in order to
protect the user or operator against risk of electric shock and
energy hazard, and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and
strength, enclosure construction and protection against the risk of
fire.
Note:
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal opera-
tion fails.
The use of shielded cables is required to comply within the limits
of Part 15 of FCC rules and EN55022
*All the safety and operating instructions should be read
before using this unit.
*The safety and operating instructions manual should be
retained for future reference.
INSTALLATION INSTRUCTIONS
*All warnings on the equipment and in the documentation
manuals should be adhered to.
Before operating this equipment please read this manual thor-
oughly, and retain it for future reference.
*All instructions for operating and use of this equipment must
be followed precisely.
Installation and preliminary adjustments should be per-
formed by qualified RUNCO personnel or by authorized
RUNCO service dealers.
On Safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
OWNER’S RECORD
Operating AC power voltage of the projector:
The part number and serial number are located at the back side of
the projector. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your RUNCO dealer
regarding this product.
DTV-992 / 992 ULTRA: 110/120 VAC, 50/60 Hz; unless other-
wise specified.
Consult your dealer to switch over from 230Vac to 120Vac or from
120Vac to 230Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
SER. NUMBER:
DEALER:
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the purpose of the
grounding-type plug.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
WARNING FOR THE CUSTOMERS: THIS APPARATUS
MUST BE GROUNDED (EARTHED) via the supplied 3 conduc-
tor AC power cable.
(If the supplied power cable is not the correct one, consult your
dealer.)
The lighting flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point whithin a triangle is in-
tended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
!
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
A. Mains lead (Power cord) with CEE 7 plug:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the equipment.
c. If the product has been exposed to rain or water.
CEE 7
The wires of the mains lead are colored in accor-
dance with the following code.
Green and yellow:
Blue:
Brown:
earth (safety earth)
neutral
line (live)
d. If the product does not operate normally when the operating instruc-
tions are followed.
LINE = BROWN
NEUTRAL = BLUE
GROUND = YELLOW / GREEN
B. Power cord with ANSI 73.11 plug:
Note: Adjust only those controls that are covered by the operating instruc-
tions since improper adjustment of the other controls may result in dam-
age and will often require extensive work by a qualified technician to
restore the product to normal operation.
The wires of the power cord are colored in accor-
dance with the following code.
ANSI 73.11
Green/yellow:
White:
Black:
ground
e. If the product has been dropped or the cabinet has been damaged.
neutral
line (live)
f. If the product exhibits a distinct change in performance, indicating a
need for service.
3. Do not allow anything to rest on the power
cord. Do not locate this product where persons
will walk on the cord.
Replacement parts - When replacement parts are required, be sure the
service technician has used original RUNCO replacement parts or autho-
rized replacement parts which have the same characteristics as the
RUNCO original part. Unauthorized substitutions may result in degraded
performance and reliability, fire, electric shock or other hazards. Unau-
thorized substitutions may void warranty.
LINE = BLACK
NEUTRAL = WHITE
GROUND = YELLOW / GREEN
To disconnect the cord, pull it out by the plug.
Never pull the cord itself.
4. If an extension cord is used with this product, make sure that the total
of the ampere ratings on the products plugged into the extension cord Safety check - Upon completion of any service or repairs to this projec-
does not exceed the extension cord ampere rating. Also make sure that the tor, ask the service technician to perform safety checks to determine that
total of all products plugged into the wall outlet does not exceed 15 the product is in proper operating condition.
amperes.
On Cleaning
5. Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts that could Unplug this product from the wall outlet before cleaning. Do not use
result in a risk of fire or electrical shock.
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Never spill liquid of any kind on the product. Should any liquid or solid - To keep the cabinet looking brand-new, periodically clean it with a soft
object fall into the cabinet, unplug the set and have it checked by quali- cloth. Stubborn stains may be removed with a cloth lightly dampened
fied service personnel before resuming operations.
with mild detergent solution. Never use strong solvents, such as thinner
or benzine, or abrasive cleaners, since these will damage the cabinet.
6. Lightning - For added protection for this video product during a light-
ning storm, or when it is left unattended and unused for long periods of - To ensure the highest optical performance and resolution, the projection
time, unplug it from the wall outlet. This will prevent damage to the pro- lenses are specially treated with an anti-reflective coating, therefore,
jector due to lightning and AC power-line surges.
avoid touching the lens. To remove dust on the lens, use a soft dry cloth.
Do not use a damp cloth, detergent solution, or thinner.
On installation
On repacking
1. Do not place this equipment on an unstable cart, stand, or table. The
product may fall, causing serious damage to it.
Save the original shipping carton and packing material; they will come in
handy if you ever have to ship your equipment. For maximum protection,
repack your set as it was originally packed at the factory.
2. Do use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are provided On illumination
for ventilation; to ensure reliable operation of the product and to protect
it from overheating, these openings must not be blocked or covered. The In order to obtain the best quality for the projected image, it is essential
openings should never be blocked by placing the product on a bed, sofa, that the ambient light which is allowed to fall on the screen be kept to an
rug, or other similar surface. This product should never be placed near or absolute minimum.
over a radiator or heat register.
When installing the projector and screen, care must be taken to avoid
The projector should not be placed in a built-in installation or enclosure exposure to ambient light directly on the screen. Avoid adverse illumina-
unless proper ventilation is provided.
tion on the screen from direct sunlight or fluorescent lighting fixtures.
4. Do not block the projector cooling fans or free air movement under and The use of controlled ambient lighting, such as incandescent spotlight or
around the projector. Loose papers or other objects may not be nearer to a dimmer, is recommended for proper room illumination. Where possible,
the projector than 4” on any side.
care should also be taken to ensure that the floors and walls of the room
in which the projector is to be installed are non-reflecting, dark surfaces.
Brighter surfaces will tend to reflect and diffuse the ambient light and
hence reduce the contrast of the projected image on the screen.
On servicing
Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage potentials and risk of elec-
tric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qual-
ified service personnel under the following conditions:
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2
LOCATION AND FUNCTION OF CONTROLS
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
Comm Port
G
Comp/
VSYNC
HSYNC
VIDEO
Port 3
R
Green=Oper.
Red=Stby
B
Off On
Power/Mains
1
2
3
4
9
5
6
10
7
8
REAR PANEL TERMINOLOGY
Power Switch: press the switch to turn the projector ON.
6
7
S-VIDEO Input: (Not Active)
1
Depending on the hardware set-up of the projector during
installation, the projector switches to ‘Standby’ or to ‘Opera-
tional’ mode. If in standby, the standby LED lights up.
75 ohm Termination Switch for S-Video signals
VIDEO Input: (Not Active)
2
3
AC Power Input
8
9
Communication Port
•
allows connection of a remote IR receiver unit to the
projector.
75 ohm Termination Switch for Video signals:
(Not Active)
Port 3
4
5
RGB Analog Input (9 pin female sub D connector). Allows a
character generator, microcomputer, etc. having analog
RGB outputs to be connected to the projector.
Projector Pilot Lamp: indicates the Status of the
10
projector.
–
–
unlit: mains (power) switch is not pressed.
lit: mains (power) switch is pressed and the
indicated color shows the projector mode:
Green color : operational mode of the projector.
Red color: standby mode of the projector.
Port 4/5: RGB-S Input (5x BNC connector):
RGB-S input: allows a character generator, microcomputer,
video camera, etc. having analog RGB Output to be con-
nected to the projector.
Line inputs
–
–
–
signals RED-GREEN-BLUE
COMPOSITE sync. signal
Tri level sync. signal (option>)
RS232 IN RS232 OUT IR REMOTE
R S 2 3 2 I N
R S 2 3 I R 2 O T U E T R E M O
11
12
13 14
15
FRONT PANEL TERMINOLOGY
11
13
RS 232 Input Port
IR Sensor
Connection between the DTV-992 / 992 ULTRA and an IBM
PC (or compatible) Or MAC (RS422) for remote computer
control and data communication.
receiver for control signals transmitted from the
RCU.
IR Remote
14
15
RS 232 Output Port
RS232 Input Port allows a communication link for PC 0r
MAC to the next projector in a series of projector.
Connector for remote input for hard wired remote
Control.
12
EYE-Q Camera
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION AND FUNCTION OF CONTROLS
Control panel terminology
a. The Local Keypad
Getting Access
The local keypad is underneath the top cover door with the Runco
logo.
To open this door, push as indicated on drawing and turn it to the
front side of the projector.
This local keyboard has the same functions as the Remote Control
Unit (RCU)
b. RCU control panel terminology
This remote control includes a battery powered infrared (IR) trans-
mitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation and
set-up. It includes automatic storing of
picture controls (Brightness, Sharpness )
– picture geometry adjustments
– convergence adjustments
Other functions of the remote control are:
–
–
switching between standby and operational modes
switching to “pause” (blanked picture, full power for immediate
restarting)
– direct access to all connected sources
– variable adjustment speed : when pushing continuously on the
control stick or the picture keys, the adjustment will be executed in
an accelerated fashion.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION AND FUNCTION OF CONTROLS
IR Transmission Indicator
1
2
3
ADJ. : Adjust key, to enter or exit the adjustment mode.
stand-by
color
brightness
contrast
Address key (recessed key) : to enter the address of the projec-
tor (between 0 and 9). Press the address key, followed by press-
ing one digit button between 0 and 9. When addressed to O , the
remote will talk to any projector, regardless of its address.
pause / park
sharpness
tint
STBY : Stand by button:
- To initiate remote power up operation
- To stop projection without main power off.
4
Pause : To mute the image, press PAUSE. The image disappears
5
6
but full power is retained for immediate restarting.
Mute : Not used
For Future Use
14
Help : Not used.
7
Digit buttons : Direct aspect ratio selection.
Sound controls : Not used.
ENTER : To start up the adjustment mode or to confirm an
15
16
8
adjustment or selection in the adjustment mode.
Control disc : To make menu selections when in the adjustment
mode. Also allows to increment or decrement an adjustment in
the adjustment mode.
9
Picture controls : Use these buttons to obtain the desired level
(see also ‘Controlling’) for each picture function.
Control disc up = up arrow in the menus
10
11
Control disc down = down arrow in the menus
Control disc to the right = arrow to the right on the menus
Control disc to the left = arrow to the left on the menus
Phase : Not used.
EXIT : To leave the adjustment mode or to scroll upwards when
in the adjustment mode.
17
Text : When adjusting one of the image controls during a meet-
ing, the displayed bar scale can be removed by pressing ‘TEXT’
key first. To re-display the bar scale on the screen, press
‘TEXT’ key again. ‘TEXT’ key is only active in operational
mode. When ‘TEXT’ is off, no warning message will be dis
played.
12
18
For Future Use
13
FREEZ : Not used.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
3
AC Power (mains) Cord Connection
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the backside of the projector.
Comm Port
Port 3
G
Comp/
VSYNC
HSYNC
VIDEO
R
B
Green=Oper.
Red=Stby
Power Check
Power voltage indication on sticker on the back side of the projector.
The power voltage is indicated here.
Warning!
Off On
Power/Mains
Check if the indicated power voltage corresponds to that of the wall
outlet.
If the wall outlet voltage is different, call a Runco technician for
power adaptation of the projector.
Switching On/Off
The projector is switched ON and OFF using the power
(mains) switch ON/OFF.
;laksdjf;lkdj;flkj;lkssd;fl
;'lakjdl;kjlnmfoomnfl;jk
Pressed : ON
Not pressed : OFF
The projector can start now in the ‘operational mode’
(image displayed) or in the ‘stand by mode’, depending on
the position of the ‘power up’ dip switch on the controller
unit. This DIP switch must be set during installation by a
qualified technician, If you want to change this start up
mode, call a qualified technician.
RS232 IN RS232 OUT IR REMOTE
R S 2 3 2 I N
R S 2 3 I R 2 O T U E T R E M O
Stand by indication lamp:
no light up: projector switched OFF
green color: projector in Operational mode
red color : projector is in Standby mode.
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
VIDEO
Green=Oper.
Red=Stby
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
When starting up the projector, with the power switch or via the
stand-by key, the projector can start up in two ways if the “CRT
run in” cycle option is switched OFF.
-
-
full white image (projector warm up) or
immediately image display.
The way of starting up can be set in the service mode.
Start up with full white image.
The next menu will be displayed for 30 seconds.
PROJECTOR WARM UP
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES
a. Start up with warm up period.
If no action is taken, a white image will be displayed for 20 min-
utes.
FOR IMMEDIATE USE OF
THE PROJECTOR, PRESS
<EXIT>
WARNING: SKIPPING THIS
PROCEDURE CAN REDUCE
THE INITIAL PICTURE
QUALITY OF THE PROJECTED
IMAGE.
This white image will be shifted on the faceplate of the CRT to
avoid burn in. During this warm up period, it is possible to interrupt
this white image projection by pressing the EXIT key. The previous
menu will be repeated for another 30 seconds but the remaining
time will be indicated.
If EXIT is pressed, the remaining warm up period will be shipped.
THIS OPTION CAN BE
DISABLED IN THE SERVICE
MENU
During the warm up period, every 30 seconds a text box with the
remaining time will be displayed on the screen for 2 seconds. This
text box will be displayed every time on another place.
REMAINING
PROJECTOR
WARM UP
TIME
18.5 MIN
If another key, different from EXIT, is pressed, a text box with fol-
lowing text will be displayed:
Please use <EXIT> to leave this procedure.
b. Start up without warm up period.
PLEASE USE
<EXIT> TO
LEAVE THIS
PROCEDURE
If the EXIT key is pressed, the warm up period will be skipped and
the projector is immediately ready for use.
Warning : skipping this warm up procedure can reduce the
initial picture quality of the projected image.
Signal Input Connection to the Projector:
-
-
-
-
Composite Video
S-Video
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
Comm Port
G
Comp/
VSYNC
HSYNC
VIDEO
Port 3
R
B
Green=Oper.
Red=Stby
RGBS or RGsB
RGB3S or RG3sB (option)
Off On
Power/Mains
3
4
5
2
1
Port No.
Projector Input
Not Used
Press Digit Button
Not Used
1
2
1
Not Used
Not Used
Not Used
Not Used
2
3
RGB2
3
4 or 5
6
Input signal : R-Y, Y and B-Y with separate composite sync or
with separate Hor and Vert. sync or with composite sync on Y.
3
4/5
4/5
4/5
4/5
RGB2
4
5
*
Input signal : R, G and B with separate Tri level sync or with
Tri-level sync on green.
Component Video3
RGB with Tri-Level Sync4
Input signal : R-Y, Y and B-Y with separate Tri level sync or
with composite Tri-level sync.
7
Video or S-Video : switchable in the Picture Tuning menu.
Component Video
with Tri-Level Sync5
8
Only available when the optional Tri-level sync module is installed.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting a RGB Analog source with composite
sync.
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
RGB analog input terminals with composite sync input or
with sync on green. The projector detects automatically
where the sync signal is located.
Always use an interface when a computer and local mon-
itor have to be connected to the projector. Examples of
interfaces which can be applied :
ANALOG INTERF 120 MHz
INPUT
B
ON
H
V
OFF
R
G
INP
INP
RGBS or RGsB input selection
a. With the RCU: Select RGB in the Source Selection
menu
b. With the local keypad :
(to gain access to the local keypad, see ‘Local key-
pad’ in chapter “Location and function of controls’.)
-Press ADJUST key, the General access menu is
displayed on the screen.
-Use the control disk to highlight 3.
-Press ENTER to select the highlighted source.
Connecting a RGB Analog source with Tri-level sync.
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
RGB analog input terminals with Tri level sync input or
with Tri-level sync on green. The projector detects auto-
matically where the sync signal is located.
ANALOG INTERF 120 MHz
INPUT
B
ON
H
V
OFF
G
R
INP
INP
RGB3S or RG3sB input selection
a. With the RCU: Select RGB in the Source Selection
menu
b. With the local keypad :
(to gain access to the local keypad, see ‘Local key-
pad’ in chapter ‘Location and function of controls’.)
-Press ADJUST key, the General access menu is
displayed on the screen.
-Use the control disk to highlight 4.
-Press ENTER to select the highlighted source.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting a Component source.
(R-Y)Y(B-Y) analog input terminals with sync input or
with sync on the luminance (Y) input. The projector
detects automatically where the sync signal is located.
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
Comm Port
G
Comp/
VSYNC
HSYNC
VIDEO
Port 3
R
B
Green=Oper.
Red=Stby
Off On
Power/Mains
Audio amplifier
VCR HDTV player
(R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) input selection
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
a. With the RCU: Select “Component” in the Source
Selection Menu
Comm Port
G
Comp/
VSYNC
HSYNC
VIDEO
Port 3
R
B
Green=Oper.
Red=Stby
Off On
Power/Mains
b. With the local keypad :
(to gain access to the local keypad, see ‘Local
keypad’ in chapter ‘Location and function of con-
trols’.)
-Press ADJUST key, the General access menu
is displayed on the screen.
-Use the control disk to highlight 5.
-Press ENTER to select the highlighted source.
Audio amplifier
VCR HDTV player
Connecting a Component source with Tri-level
sync.
This device complies with part 15 of
the FCC rules. Operation is subject to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this device must
accept any interference received
including interference that may cause
undesired operation.
Comm Port
G
Comp/
VSYNC
HSYNC
VIDEO
Port 3
R
B
Green=Oper.
Red=Stby
Off On
Power/Mains
(R-Y)Y(B-Y) analog input terminals with Tri-level
sync input or with Tri-level sync on the luminance
input.
Audio amplifier
VCR HDTV player
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
(R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) input selection
GENERAL ACCESS
SHARPNESS
TINT
a. With the RCU: Select “Component” in the Source Selection Menu
5
3
1
6
4
2
COLOR
BRIGHTNESS
CONTRAST
b. With the local keypad :
(to gain access to the local keypad, see ‘Local keypad’ in chapter
‘Location and function of controls’.)
Enter ADJUST
Select with
,
-Press ADJUST key, the General access menu is displayed on
the screen.
-Use the control disk to highlight 6.
-Press ENTER to select the highlighted source.
or
then <ENTER>.
<EXIT> to return
FROM LOCAL KEYPAD
SOURCE SELECTION
SELECT AN INPUT
FROM BELOW:
RGB
S-VIDEO
VIDEO
COMPONENT VIDEO
Select with
or
then <ENTER>
<EXIT> to return
FROM RCU
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS232 input of the projector.
RS232 IN RS232 OUT IR REMOTE
R S 2 3 2 I N
R S 2 3 I R 2 O T U E T R E M O
RS232 Ports
In/Out
The projector has a RS232 port that allows it to communicate with a computer.
Applications: remote control and data communications.
a) remote control:
-easy adjustment of the projector via IBM PC (or compatible) or
MAC connection.
-allow storage of multiple projector configurations and set ups.
-wide range of control possibilities.
-address range from 0 to 255.
b) data communications:
-sending data to the projector or copying the data from the pro-
jector to a hard memory device.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLLING
4
Caution : Do not display a stationary image with full brightness
and contrast for longer than 10 min., otherwise you risk damage
to the CRTs.
Battery installation in the RCU.
A new battery (not yet installed to save the battery life) is delivered inside the plastic bag
with the power cord. Install the battery as follows :
Remove the battery cover on the backside of the RCU by pushing the indicated handle a
little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
Insert the new 9 V battery (type 6F22S or equivalent) in the lower compartment and con-
nect the battery to the contact plate.
Insert the battery into the lower compartment and put the cover back.
fig.1
Behind the
plastic cover,
Contact
plate
insert the 'card
for RCU'. You
can cut out the
insert card on
the last page of
the installation
manual.
Battery
fig.2
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling
The DTV-992 / 992 ULTRA can be controlled with
a. The RCU
c. Using your RCU.
b. The hardwired RCU (cable not included)
c. The local keyboard
Before using your RCU, it is necessary to enter the projector
address into the RCU (only when that address is between 1 and
9). The projector with the corresponding address will listen to that
The procedure and results of controlling the projector with either of specific RCU.
these RCU options is essentially the same.
When address 0, ‘zero address’ is programmed into the RCU,
every projector, without exception will listen to the commands
given by this RCU.
How to use your RCU
How to display a projector address?
a) Point the front of the RCU towards the projector
Press the ADDRESS key (recessed key on the RCU) with a pen-
cil. The projector’s address will be displayed in a ‘Text box’. This
text box disappears after a few seconds.
Ceiling
IR sensor
Screen
RCU
PROJECTOR ADDRESS
001
b) RCU used in a hardwired configuration.
To continue using your RCU, it is necessary to enter the same
address with the digit buttons (address between 0 and 9). For
example, if the Address Key displays projector address 003, then
press the “3” digit button on the RCU to set the RCU’s address to
match the projector’s address. Do not press digit 003. This will
address the remote to ‘0’ and control all projectors in the room.
RS232 IN RS232 OUT IR REMOTE
R S 2 3 2 I N
R S 2 3 I R 2 O T U E T R E M O
How to program an address into the RCU?
Press the ADDRESS key (recessed key on the RCU) with a pen-
cil and enter the address with the digit buttons. That address can
be any digit between 0 and 9.
When programming ‘0’, zero address, the RCU will control a pro-
jector regardless of the projector’s address. This feature allows
multiple projectors with different addresses to be controlled by a
single RCU.
Plug one end of the remote cable in the connector on the bottom
of the RCU and the second side in the connector in the rear panel
of the DTV-992 / 992 ULTRA labeled ‘REMOTE’.
Projector Address
a. Hardware set up of the projector address.
Every projector requires an individual address between 0 and 255
which is set with hardware DIP switches inside the projector. To
change that address, contact a RUNCO authorized technician.
b. How to control the projector.
The projector’s address may be set to any value between 0 and
255. When the address is set, the projector can be controlled now
with :
-the RCU for addresses between 1 and 9.
-computer, e.g. IBM PC (or compatible), Apple MAC, etc.
for addresses between 0 and 255.
Note : A projector will respond to a RCU set to an address of ‘0’
regardless of what address is set in the projector itself. Address “0”
is therefore a universal address.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling
Input selection.
Choose from table above. Push the control disk up or down to
move the cursor up and down, push the control disk to the left or
to the right to move the cursor to the left and to the right.
Press ENTER to confirm your selection.
GENERAL ACCESS MENU ITEMS
SOURCE
Projector input
When a valid and available source is selected, there will be infor-
mation displayed on the screen about that source. This informa-
tion includes :
1
2
3
4
5
Comp. Video
S - Video
- Source number
- Horizontal frequency
- Vertical frequency
RGBS of RGsB
RGB3S or RG3sB
(R - Y) Y (B - Y)3S or
(R - Y)Ys(B - Y)
Source 2
Fh = 15.6 kHz
Fv = 50 Hz
6
(R - Y) Y (B - Y)3S or
(R - Y)Y3s(B - Y)
When the entry is a non valid source number, a warning appears
on the screen : ‘input not available’.
Two possible ways of selecting an input :
a) Display General access menu with RCU by pressing ADJ but-
ton. This brings up a secondary general access menu. Choose
source selection and highlight desired source.
b) With the local keypad :
Press first the ADJUST key to display the General access menu.
Use the control disk to highlight the desired source number.
Warning
input not
available
When a valid source number is selected, the projector will display
this source or it will wait on the selected source number until the
source becomes available. A message ‘source not available’ will
be displayed for a short time.
EXIT
ADJUST
ENTER
STANDBY
GENERAL ACCESS
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
Warning
source not
available
5
3
1
6
4
2
Enter ADJUST
Select with
,
or
then <ENTER>.
<EXIT> to return
General Access From Local Keypad
GENERAL ACCESS
GENERAL ACCESS
SELECT AN OPTION
FROM BELOW:
SELECT AN OPTION
FROM BELOW:
SOURCE SELECTION
EYE-Q
ADJUSTMENT MODE
SOURCE SELECTION
EYE-Q
ADJUSTMENT MODE
Select with
or
then <ENTER>
<EXIT> to return
Select with
or
then <ENTER>
<EXIT> to return
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling
Tint Control
Analog Picture Controls
Tint is only active for Video and S-Video. Tint control is effective
only when using the NTSC 4.43 or NTSC 3.58 system. A bar scale
gives a visual indication on the screen of the current tint setting
while pressing the + or - buttons (RCU) or pushing the control disk
to the left or to the right (local keypad). If the bar scale is not visi-
ble on the screen, press the ‘TEXT’ key once and retry the above
indicated buttons.
The analog picture controls can be adjusted with the RCU. The
control keys are located on the lower right side of the key panel of
the RCU and indicated with the name of the control and an icon.
When an analog picture control is pressed, a text box with bar
scale and the function name of the control, e.g. ‘brightness...’
appears on the screen (only if ‘TEXT’ is ON). The length of the bar
scale indicates the current memorized setting for this source. The
bar scale changes as the + or - buttons of the control are pressed.
The bar scale increases when pressing on the + button and
decreases when pressing the - button.
Sharpness Control
Sharpness control is only active for Video and S-Video. A bar scale
gives a visual indication on the screen of the current sharpness
setting while pressing the + or - buttons (RCU) or pushing the con-
trol disk to the left or to the right (local keypad). If the bar scale is
not visible on the screen, press ‘TEXT’ key once and retry the
above indicated buttons.
The bar scale increases when pressing on the + button (sharper
picture) and decreases when pressing on the - button (softer pic-
ture).
BRIGHTNESS
40
The Pause key
When the Pause key is pressed, the image projection is muted but
the projector remains with full power for immediate restart.
To restart the image :
Brightness Control
- Press the Pause key,
A correct ‘brightness’ setting is important for good image repro-
duction. Adjust the brightness with the + or - button (RCU) until the
darkest parts of the picture appear black.
- Select a source number.
A bar scale gives a visual indication on the screen of the current
brightness setting while pressing on the above indicated keys. If
the bar scale is not visible on the screen, press ‘TEXT’ key once
and retry the above indicated keys.
The bar scale increases when pressing on the + button (higher
brightness) and decreases when pressing on the - button (lower
brightness).
GENERAL ACCESS
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
Contrast Control
Quit ADJUST
A correct ‘contrast’ setting is important for good image reproduc-
tion. Adjust the contrast to the level you prefer, according to room
lighting conditions. If the Contrast Control is too low, the picture will
be too dim. If it is set too high, the picture may be too bright and
not sharp. A bar scale gives a visual indication on the screen of the
current contrast setting while pressing the + or - buttons (RCU). If
the bar scale is not visible on the screen, press ‘TEXT’ key once
and retry the above indicated keys.
Select with
or
then <ENTER>
<EXIT> to return
The bar scale increases when pressing on the + button (higher
contrast) and decreases when pressing on the - button (lower con-
trast).
The GENERAL ACCESS MENU is available
from the LOCAL KEYPAD.
Press the ADJ 3X to display.
Color Saturation Control
Color saturation is only active for Video and S-Video. Adjust the
color intensity of the picture. Adjust the color saturation using the
= and - buttons (RCU) or pushing the control disk to the left or to
the right (local keypad). A bar scale gives a visual indication on the
screen of the current color setting while pressing on the above indi-
cated buttons. If the bar scale is not visible on the screen, press
‘TEXT’ key once and retry the above indicated buttons. The bar
scale increases when pressing on the + button (richer colors) and
decreases when pressing the - button (lighter colors).
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
START UP OF THE ADJUSTMENT MODE
5
Adjustment mode
All picture geometry and convergence adjustments are made while in the ‘Adjustment mode’. Two possible ways to enter the adjust-
ment mode:
a) Using the RCU.
Press the ADJUST key.
The projector displays the path selection menu.
b) Using the local keypad.
Press the ADJUST key.
The projector displays the General access menu.
EXIT
ADJUST
Use the control disc to highlight enter ADJUST and press ENTER.
The path selection menu will be displayed.
ENTER
STANDBY
GENERAL ACCESS
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
5
3
1
6
4
2
Enter ADJUST
Select with
,
or
then <ENTER>.
<EXIT> to return
General Access From Local Keypad
Note: to adjust the Analog picture control while in the ‘Adjustment
mode’, press the ADJUST key. The next General Access menu will be
displayed.
GENERAL ACCESS
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
Push the control disc up or down to select the analog control to be
adjusted and press the ENTER key to confirm.
When the analog control is adjusted the projector returns automatically
to the General access menu. When you want to return to the Adjustment
mode, press EXIT, otherwise select quit ADJUST and press ENTER to
return to operational mode.
You are now in the ‘Adjustment mode’. The control disc is used to make
menu selections and also vertical and horizontal adjustments. The
ENTER and EXIT keys are used to move forward and backward through
the menu structure. The ADJUST key can be used to terminate the
adjustment mode while a path selection menu (head menu) is displayed.
Quit ADJUST
Select with
or
then <ENTER>
<EXIT> to return
There are 5 possible paths to follow once in the Adjustment mode. They
are :
ADJUSTMENT MODE
INSTALLATION - Installation should be selected if the projector has
been relocated and/or a different screen size is desired.
When selecting ‘Installation’, the user or operator will be warned to call
a qualified technician to perform the installation procedure (see exam-
ple of projected warning on next page).
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
GUIDED - Guided should be selected if the user intends to perform a
complete alignment of the projected image. All of the necessary geom-
etry and convergence adjustments are made in a predetermined
sequence.
EYE-Q
Source 1
Select with
or
then <ENTER>
<EXIT> to return
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Start Up of the Adjustment Mode
RANDOM ACCESS - Random Access should be selected if the user intends to
make only a few adjustments.
SERVICE - Service should be selected if the user intends to delete blocks,
change password or apply information.
ADJUSTMENT MODE
Select a path from below :
EYE-Q - This selection will only be available when the subconvergence unit
EYE-Q is connected to the projector.
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
While in Guided or Random Access adjustment Mode, the user may use an
external source, an internally generated genlocked pattern or an internally gen-
erated multifrequency cross hatch pattern as a setup pattern. Some items in the
Adjustment mode are password protected. While selecting such an item, the
projector asks you to enter your password. (Password protection is only avail-
able when the password DIP switch on the controller module is in the ON posi-
tion. Contact a RUNCO authorized technician when no password is requested
during the adjustment procedure and password protection is desired.)
EYE-Q
Source 1
Select with
or
then <ENTER>
<EXIT> to return
Your password contains 4 digits.
a) Adjusting the projector with the RCU.
Enter the digits with the numeric keys on the RCU.
Example : 2 3 1 9
enter
password
X X X X
For each digit entered, a ‘X’ appears on the screen under the displayed text
‘enter password’
When your password is correct, you get access to the ‘Adjustment mode’. When
the entered password is wrong, the message ‘Wrong password !!!’ will be dis-
played. The projector stays on the previous selected item.
Factory programmed
password : 0000
wrong
password
b) adjusting the projector with the local keypad.
When the ‘compose password’ menu is displayed, select with control disc the
first digit of your password and press ENTER. Continue by selecting the second
digit with the control disc and press ENTER. Handle in the same way for the
third and fourth digit.
COMPOSE
PASSWORD
???
7
4
1
8
5
2
0
9
6
3
When your password is correct, you get access to the ‘Adjustment mode’.
When the entered password is wrong, the message ‘Wrong password’ will be
displayed.
Select with
,
or
Once the password is correctly entered, all other password protected items are
accessible without re-entering your password.
When re-entering the adjustment mode, it will be necessary to enter your pass-
word again when selecting a password protected item.
then <ENTER>
<EXIT> to return
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
RANDOM ACCESS ADJUSTMENT MODE
6
Starting up the random access adjustment mode
Push the control disc up or down to highlight “RANDOM ACCESS”
and the press ENTER.
ADJUSTMENT MODE
Some items in the Random access mode are password protected
(when the password function is enabled). Enter your password to
continue. All other password protected items are now also available if
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
ENTER continues to Setup Pattern Selection
EXIT returns to operational mode
EYE-Q
Source 1
Select with
or
then <ENTER>
<EXIT> to return
you stay in the adjustment mode.
Overview ‘Random Access Adjustment’ mode.
COLOR BALANCE
PICTURE TUNING
SYNC
PEAKING
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
H PHASE
RASTER SHIFT
SIDE KEYSTONE
LEFT - RIGHT (E-W)
GEOMETRY
SEAGULL CORRECTION
RANDOM ACCESS
ADJUSTMENT MODE
H CENTERLINE BOW
H CENTERLINE SKEW
SETUP PATTERN SELECTION
TOP - BOTTOM (N-S)
TOP KEYSTONE
TOP BOW
SIZE
BOTTOM KEYSTONE
BOTTOM BOW
VER LINEARITY
BLANKING
SEAGULL CORRECTION
TOP BOW
BOTTOM KEYSTONE
CONVERGENCE
COLOR SELECT
BOTTOM BOW
SEAGULL GORRECTION
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Selecting Setup Pattern
If an external source is connected to the projector, this menu will be displayed. Push
the control disc up or down to highlight the desired setup pattern and then press
ENTER.
Choose a setup pattern
from below :
Genlocked pattern : internally generated cross hatch pattern, locked on the external
source.
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Internal # pattern : internally generated cross hatch pattern and locked on internal
generated sync signals. (no external source necessary)
Source 01
ENTER continues to Random Access Adjustment Mode or
Internal # Pattern Selection.
EXIT returns to Path Selection menu.
ADJUST returns to Operational mode.
Select with
or
then <ENTER>
<EXIT> to return
If no external source is connected to the projector, the internal cross hatch pattern
menu will be displayed.
Note: The menus in the manual are created for an external source, connected to one
of the inputs, and the ‘Genlocked Pattern’ is selected.
Internal Cross Hatch Pattern
The internal # pattern menu will be displayed if the internal cross hatch pattern has
been selected or if no source is connected to the projector.
INTERNAL # PATTERN
kHz / Hz
The table below lists the 8 fixed factory preset frequencies available. Another 8
blocks are custom programmable.
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
PAL/SECAM
NTSC
EDTV
IDTV
HDTV EUREKA
HDTV ATV
Push the control disc up or down to highlight the desired cross hatch frequency.
Push the control disc to the left or to the right to scroll to another page. Press
ENTER if the desired block is selected.
Select with
scroll with
<ENTER> to accept
<EXIT> to return
or
or
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
33.7/60
15.8/60
21.8/60
31.5/60
31.5/70
35.5/97
44.2/70
48.5/60
61.0/76
63.9/76
PAL/SECAM
NTSC
EDTV
IDTV
HDTVEUREKA
HDTV ATV
HDTV HIVISION
EGA 1
EGA 2
VGA 3
XGA 1,2
VGA 4
SUPER VGA 2
SUPER VGA 1
SUPER VGA 3
APOLLO
ENTER continues to the Random Access Adjustment Mode.
EXIT returns to the Setup Pattern Selection menu.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Random access adjustment mode selection menu
RANDOM ACCESS
ADJUSTMENT MODE
This is the main menu for the Random Access adjustment mode.
Through this menu, the following adjustments and features are accessible:
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
- Picture Tuning
Sync slow/fast (video/s-video)
Color Balance
- Geometry
Convergence
- Color Select
Select with
or
then <ENTER>
<EXIT> to return
And also Orbiting, Contrast modulation and Soft Edge, if these options are
installed.
Picture Tuning
Highlight Picture tuning by pushing the control disc up or down and press
ENTER.
PICTURE TUNING
The Picture tuning menu will be displayed.
Depending on the input source, the ‘Picture tuning’ menu will display differ-
ent items.
COLOR BALANCE
SYNC : FAST
PEAKING : ON
- Color Balance
- Sync slow/fast
- Peaking
Select with
or
<ENTER> to accept
<EXIT> to return.
Color Balance
The Color Balance function is used to select or adjust the color temperature
of white used by the projector.
The Color Balance can be adjusted in two different ways:
- fixed color balance. You have the choice between 3200k (reddish), 5400
K, 6500 K (white), or 9300 K (bluish).
PICTURE TUNING
- Custom white and black balance.
Fixed Color Balance
Highlight one of the 4 programmed color temperatures with the control disc
and press ENTER to display the desired color balance.
COLOR BALANCE
SYNC : FAST
PEAKING : ON
Custom Color Balance
Select custom white balance by pushing the control disc up or down and
press ENTER to start the adjustment.
COLOR BALANCE
Push the control disc up or down to adjust the red gain and push the control
disc to the left or right to adjust the blue gain. A bar scale indicates the
amount of adjustment.
FIXED COLOR BALANCE
3200 5400 6500 9300
Select custom black balance with the control disc and press ENTER to start
the adjustment.
CUSTOM WHITE BALANCE
CUSTOM BLACK BALANCE
Push the control disc up or down to adjust the red cut-off and push the con-
trol disc to the left or to the right to adjust the blue cut-off.
When the color balance is adjusted, select continue by pushing the control
disc up or down and press ENTER.
Select with arrow keys
then <ENTER>
You can
adjust red with
Blue with
<EXIT> to return
or
or
Sync Fast/Slow Adjustment
The sync function is used to minimize horizontal jittering or tearing at the
top to the displayed image.
Highlight SYNC with the control disc and press ENTER to toggle between
FAST and SLOW.
Note: SYNC is normally used in the SLOW position. The FAST position is
used to compensate for unsteady sync pulses from older video playback
equipment, such as a VCR.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING : ON
ENTER will toggle Sync between FAST and SLOW.
EXIT will return to the Random Access Adjustment menu.
Select with
or
<ENTER> to accept
<EXIT> to return.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Peaking
Peaking improves the contours in a projected image. Highlight PEAKING
by pushing the control disc up or down and press ENTER to toggle the
peaking between OFF and ON. During the creation of new settings for a
RGB source the peaking is switched to OFF.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING :
OFF
Select with
or
<ENTER> to accept
<EXIT> to return.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
Color Select
COLOR SELECT
Highlight COLOR SELECT by pushing the control disc up or down and
press ENTER to display the color select menu.
COLOR SELECT
RED
GREEN
BLUE
ENTER continues to the color select menu.
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu.
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
ADJUST returns to operational mode.
Select with
<ENTER> to accept
<EXIT> to return.
or
Use the control disc to highlight a color (CRT) or combination of colors to
display the projected image in that specific color.
To select a new color, press ENTER, the color selection menu appears.
ENTER continues to the color select menu.
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu.
ADJUST returns to operational mode.
PICTUREE TUNING
Clamp Tuning
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
LINE DOUBLER : ON
Highlight CLAMP TUNING by pushing the control stick forward or back-
ward and press ENTER to toggle between NORMAL and RESTORATION.
Select Normal :
or
Select with
then <ENTER>
- for all standard sources and all sources with a bac porch > 0.8ms,
- for sources with noise and spikes in the signal.
Select Restoration
to return.
<EXIT>
- for standard sources with a backporch between 0.4 ms and 0.8 ms,
- for sources with sync separate or sync on Green.
PICTUREE TUNING
Port 2 : Video or S-Video
COLOR BALANCE
PORT2 : S-VIDEO
LINE DOUBLER : ON
Port 2 can be used as a Video or S-Video input.
Highlight Port2 by pushing the control stick forward or backward and
press ENTER to toggle between VIDEO and S-VIDEO.
or
Select with
then <ENTER>
to return.
<EXIT>
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Focusing
RANDOMM ACCESS
ADJUSTMEENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
Before starting the ‘focusing’ adjustment, be sure the lenses are
correctly focused.
Push the control stick forward or backward to select ‘Focusing’
and press ENTER.
COLOR SELECT
ENTER continues to the Focusing color select menu.
EXIT returns to Internal Crosshatch Selection or Setup Pattern
Selection menu.
FOCUSING
RED
GREEN
BLUE
ADJUST returns to operational mode.
BLUE ON SOURCE
Focusing color select
or
Select with
The focusing has to be done for the three colors separately.
Therefore, start by selecting Green by pushing the control stick
forward or backward and adjust Midpoint, top, bottom left and right
focusing. Return to this focusing color select menu and continue
with Red and Blue. Repeat for both colors Midpoint, top, bottom
left and right focusing.
then <ENTER>
to return.
<EXIT>
ENTER selects the focusing menu for the selected color.
EXIT returns to the Random access main menu.
Midpoint focusing
Push the control stick forward or backward to select midpoint and
press ENTER continue with the midpoint focusing.
FOCUSING
Adjust by pushing the control stick to the left or to the right until
the center of the image is sharp.
Press ENTER to return to the focusing menu.
RED
GREEN
BLUE
BLUE ON SOURCE
Top image focusing
The same procedure has to be repeated as for the midpoint focus-
ing. Push the control stick forward or backward and press ENTER
to continue to the top focusing.
Push the control stick to the left or to the right to adjust the top
focusing. Adjust until the upper part of the image is sharp. ENTER
to return to the Green Focusing menu.
GREEN FOOCUSING
MIDPOINT
TOP
BOTTOM
FOCUSING
LEFT
RIGHT
or
Select with
Bottom image focusing
then <ENTER>
to return.
<EXIT>
The same procedure has to be repeated as for the midpoint focusing.
Push the control stick forward or backward to select bottom and
press ENTER to continue to the bottom focusing.
Push the control stick forward or backward to adjust the bottom
focusing. Adjust until the lower part of the image is sharp.
ENTER to return to the Green Focusing menu.
Left image focusing
The same procedure has to be repeated as for the midpoint focusing.
Push the control stick forward or backward to select LEFT and
press ENTER to continue to the left focusing.
Push the control stick forward or backward to adjust the left focusing.
Adjust until the left part of the image is sharp.
ENTER to return to the Green Focusing menu.
Right image focusing
The same procedure has to be repeated as for the midpoint focus-
ing. Push the control stick forward or backward to select RIGHT
and press ENTER to continue to the right focusing.
Push the control stick to the left or to the right to adjust the right
focusing. Adjust until the right part of the image is sharp. ENTER
to return to the Green Focusing menu.
When on the Green Focusing menu, press EXIT to return to the
focusing color select menu and continue with the other colors.
Blue on source
After focusing the three color, and a discoloring on a normal image
is still visible, select ‘Blue on source’ on the Focusing menu and
repeat the above steps for Midpoint, top, bottom left and right focusing.
Press EXIT to return to focusing menu.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Geometry Adjustments
The geometry adjustments have to be done only on the green image. These adjust-
ments are automatically implemented for the other color images : Left-right (EW) and
Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical
Linearity and Horizontal Phase.
Highlight GEOMETRY by pushing the control disc up or down and press ENTER to
display the geometry menu.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
ENTER will display Geometry menu.
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu.
ADJUST returns to operational mode.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
SIZE
Within the Geometry Adjustment menu, the following adjustments are available :
- Horizontal Phase (not for internal # pattern).
- Raster Shift
V LINEARITY
BLANKING
- Left-Right Corrections
- Top-Bottom Corrections
- Horizontal Size
- Vertical Linearity
Select with
then <ENTER>
or
- Vertical Size
<EXIT> to return.
- Blanking
The convergence corrections are disabled during geometry corrections. The blanking
corrections are only enabled during the blanking adjustments.
Horizontal Phase Adjustment
GEOMETRY
Push the control disc up or down to highlight H PHASE on Geometry menu and the
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
SIZE
press ENTER.
Note : No horizontal phase adjustment is available on the internal # pattern.
V LINEARITY
BLANKING
For external sources :
If the raster shift is correctly adjusted, the H Phase text box is projected in the mid-
dle of the raster. At that moment, the “><” icon indicates the middle of the raster.
Adjust the H Phase control until the middle of the projected image is equal with the
middle of >< icon.
Note : If the genlocked pattern was selected, the external source will be displayed.
A bar scale and a number indicator (between 0 and 100) on the screen give a visu-
al indication of the horizontal phase adjustment.
H PHASE
70
ENTER continues to geometry menu.
Push the control disc to
the right to correct
Push the control disc to
the left to correct
H PHASE
70
H PHASE
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Raster Shift Adjustment
GEOMETRY
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
SIZE
The green raster must be centered both horizontally and vertically on the
center of the CRT surface. To center the green raster, look into the green
lens and use the control disc to move the raster.
CAUTION
V LINEARITY
BLANKING
It is necessary to look into the lenses to perform these adjustments. To
avoid eye discomfort while looking into the lenses, reduce the contrast and
gradually increase the brightness level until the raster becomes visible on
the face of the CRT.
COARSE SHIFT
GREEN HORIZONTAL
GREEN VERTICAL
RED VERTICAL
BLUE VERTICAL
ENTER will select green raster shift adjustment.
EXIT returns to random access adjustment mode menu.
Select with
then <ENTER>
or
<EXIT> to return.
Warning : In order to ensure maximum CRT longevity and to
avoid CRT damage, do not shift the raster outside the phosphor
area of the CRT.
To start the adjustment, use the control disc to highlight Raster shift and
press ENTER to display the green raster on the phosphor.
forbidden area
projected raster
correct raster position
wrong raster position
crt faceplate border
phosphor border
Press EXIT to return to the Geometry menu.
Note : Horizontal and Vertical shifts for Red and Blue should
end up with a setting close to 50%. If these settings are sig-
nificantly greater or lesser than 50%, contact a RUNCO
authorized service technician.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Left-Right (east-west) Adjustments
GEOMETRY
Left-right and center adjustments affect only the vertical lines
of the projected image.
H PHASE
RASTER SHIFT
To start up the left-right and center adjustments, follow the
next procedure :
Push the control disc up or down to highlight LEFT-RIGHT
(E/W) on the geometry menu and then press ENTER.
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
SIZE
V LINEARITY
LEFT - RIGHT (E-W)
V CENTERLINE BOW
V CENTERLINE SKEW
RIGHT BOW
RIGHT KEYSTONE
LEFT BOW
LEFT KEYSTONE
ENTER will select Left - Right adjustment menu
EXIT returns to random access adjustment mode main menu.
ADJUST returns to Operational mode
Select with
then <ENTER>
or
<EXIT> to return.
Only the green image is displayed while making left-right
adjustments. The red and blue images will automatically be
corrected in the same manner. Convergence corrections are
automatically disabled for the duration of these adjustments.
The following adjustments can be executed
- vertical centerline bow
- vertical centerline skew
- side keystone (left - right)
- side bow (left - right)
All adjustments are indicated on the screen
with the function name, a bar scale and a
number between 0 and 100.
Adjust the next alignments until the vertical
lines are straight.
Corrects for curvature of the vertical lines in the middle of
the image.
To enter an alignment, push the control disc
up or down to highlight a function and press
ENTER to activate this function.
Press EXIT to return.
Corrects the tilting of the vertical lines in the middle of the
image.
LEFT - RIGHT (E-W)
V CENTERLINE BOW
V CENTERLINE SKEW
RIGHT BOW
RIGHT KEYSTONE
LEFT BOW
Corrects for curvature of the vertical lines on the right side.
LEFT KEYSTONE
Select with or
then <ENTER>
<EXIT> to return.
Corrects the keystone geometry correction of the vert. lines
on the right side.
Corrects for curvature of the vertical lines on the left side.
Corrects the keystone geometry correction of the vert. lines
on the left side.
Correct by pushing
the control disc to
the left.
Correct by pushing
the control disc to the
right.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Seagull correction
GEOMETRY
Use this correction only if, after adjusting the vertical lines with the
side bow or side keystone, still a ‘S’ deformation is visible on the
left and the right side of the image.
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
The default value on the bar scale for this correction is 50.
V LINEARITY
V SIZE
BLANKING
Push the control stick forward or backward to highlight SEAGULL
CORRECTION on the Left-Right menu and then press ENTER.
Eliminate the deformation by pushing the control stick to the left or
to the right until a straight line is obtained.
LEFT RRIGHT
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
or
Select with
then <ENTER>
<EXIT> to return.
Left Side Correction
GEOMETRY
Left side corrections affect only the vertical lines of the set up pat-
tern. Only the green image is displayed while making the left side
adjust-ments. The red and blue images will automatically be cor-
rected in the same manner.
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
Convergence corrections are automatically disabled for the duration
of these adjustments.
BLANKING
Look only to the left side of the image while adjusting these fine
tunings (bow and keystone). Before starting the left side correction,
insure that the side bow and keystone adjustments are done prior
to these fine adjustments!
LEFT SSIDE CCOORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are done
prior to these fine adjustments !
The following adjustments can be executed:
-
-
Left keystone
Left bow
or
Select with
then <ENTER>
Push the control stick forward or backward to highlight LEFT SIDE
CORRECTION on the geometry menu and then press ENTER.
to return.
<EXIT>
ENTER will select the Left Side Correction menu.
EXIT will return to the random access adjustment menu.
ADJUST returns to operational mode.
All adjustments are indicated on the screen with the function name,
a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines on the left side are
straight.
LEFT SIDE CORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are done
prior to these fine adjustments !
Correct the keystone geometry distortion of the
vertical lines
or
Select with
then
<ENTER>
<EXIT> to return.
To enter an alignment, push the control
stick forward or backward to highlight a
function and press ENTER to activate this
function.
Correct the bow geometry distortion of the
vertical lines
Press EXIT to return.
Correct by pushing
the control stick to the
right
Correct by pushing
the control stick to the
left
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Top-Bottom (north-south) Adjustments
GEOMETRY
Top-Bottom and center adjustments affect only the hori-
zontal lines of the projected image.
To start up the Top-Bottom and center corrections, follow
the next procedure :
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
SIZE
Push the control disc up or down to highlight TOP-BOT-
TOM (N/S) on the geometry menu and then press ENTER.
V LINEARITY
BLANKING
Only the green image is displayed while making top-bot-
tom adjustments. The red and blue images will automati-
cally be corrected in the same manner. Convergence cor-
rections are automatically disabled for the duration of
these adjustments.
TOP - BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
The following adjustments can be executed
- Horizontal centerline bow
- Horizontal centerline skew
- Top bow
- Top keystone
Select with
then <ENTER>
<EXIT> to return.
or
- Bottom bow
- Bottom keystone
All adjustment are indicated on the screen with the function
name, a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are
straight.
To enter an alignment, push the control disc up or down to
highlight a function and press ENTER to activate this func-
tion.
Press EXIT to return.
Corrects for curvature of the horisontal lines in the middle
of the image.
Corrects the tilting of the horizontal lines in the middle of
the image.
TOP - BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP BOW
TOP KEYSTONE
BOTTOM KEYSTONE
BOTTOM BOW
Corrects for curvature of the horizontal lines on the upper
side.
Select with
then <ENTER>
<EXIT> to return.
or
Corrects the keystone geometry correction of the Hor. lines
on the upper side.
Corrects for curvature of the horizontal lines on the lower
side.
Corrects the keystone geometry correction of the hor. lines
on the lower side.
Correct by pushing
the control stick
forward.
Correct by pushing
the control stick
backward.
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Size Adjustment
GEOMETRY
Push the control disc up or down to highlight SIZE on the Geometry menu and
then press ENTER.
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
ENTER will select size adjustment.
EXIT returns to random access adjustment mode menu.
ADJUST returns to operational mode.
H & V SIZE
Adjust the horizontal size by pushing the control disc to the right or to the left
until the exact image width is obtained.
Adjust the vertical size by pushing the control disc up or down until the exact
image height is obtained.
Note :
- If the internal # pattern was selected, this pattern remains on the screen.
- If the genlocked pattern was selected, the external source will be
displayed.
A bar scale and a numeric indicator help to gauge the size adjustment.
EXIT will return to Geometry.
H SIZE
70
1.33 X Height
1.78 or 1.85 units
1.78 or 1.85 units
4 Units
1.78 or 1.85 Units
Wide Format Screen
(1.78:1 or 1.85:1)
Wide Format Screen
(1.78:1 or 1.85:1)
4 X 3 Type Screen
A 4 X 3 Aspect Ratio
on a Wide Format
(1.78:1 or 1.85:1) screen
4 X 3 - Use horizontal size to make image fit width of screen, then use vertical size to make image fill height (circle is round). On a wide
format (1:78:1 or 1.85) screen, adjust width of image 1.33 X the height of the screen. Adjust the vertical size to fill the height.
WS - Use horizontal size to fill width of screen, then use vertical size to make circle round (use blanking to crop excess image top and
bottom.) This is not necessary if you are using a 4 X 3 format screen.
ANA - Use horizontal size to fill width of screen, then use vertical size to fill height of a 16 X 9 screen (circle is nor round). Alternative:
Use Anamorphic test pattern on test disc, then adjust sizing to make anamorphic circle round. This is good to use when converging an
anomorphic image onto a 4 X 3 screen.
Vertical Linearity Adjustment
GEOMETRY
The vertical linearity adjustment function corrects for vertical nonlinearities
which extend from the center of the image to the top and bottom of the
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
H & V SIZE
image.
Push the control disc up or down to highlight V LINEARITY on the Geom-
etry menu and then press ENTER.
V LINEARITY
ENTER will select vertical linearity adjustment.
BLANKING
EXIT returns to random access adjustment mode menu.
ADJUST returns to operational mode.
Adjust the vertical linearity with the control disc until the distances between
the horizontal lines of the set up pattern are equal from top to bottom.
EXIT will return the
Geometry menu.
V LINEARITY
70
6-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Blanking Adjustments
GEOMETRY
Blanking adjustments affect only the edges of the projected image
and are used to frame the projected image on to the screen and to
hide or black out unwanted information (or noise). A 0% on the bar
scale indicates no blanking.
H PHASE
RASTER SHIFT
LEFT - RIGHT (E-W)
TOP - BOTTOM (N-S)
H & V SIZE
To start up the Blanking adjustments, follow the next procedure :
Push the control disc up or down to highlight BLANKING on the
Geometry menu and the press ENTER.
BLANKING
The following blanking corrections are possible :
- Top blanking
TOP
BOTTOM
LEFT
- Bottom blanking
RIGHT
- Left blanking
- Right blanking
Therefore :
- If the internal # pattern was
selected, this pattern remains on
the screen.
Select with
then <ENTER>
<EXIT> to return.
or
- If the genlocked pattern was
selected, the external source will
be displayed.
Adjust the next blanking alignments until the
image is correctly framed or the unwanted
information is blanked out.
Top blanking
To enter a blanking alignment, push the con-
trol disc up or down to highlight a function
and press ENTER to activate this function.
Press EXIT to return.
Left blanking
Right blanking
Bottom blanking
Adjustment of the blanking on the top of the image.
BLANKING
TOP
BOTTOM
LEFT
Adjustment of the blanking on the bottom of the image.
RIGHT
Select with
then <ENTER>
<EXIT> to return.
Adjustment of the blanking on the left side.
Adjustment of the blanking on the right side.
6-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
RANDOM ACESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
COLOR SELECT
SOFT EDGE
Convergence Adjustment
Convergence adjustments affect both the horizontal and vertical lines of the
setup pattern. These adjustments are performed on the red image while
superimposed on the green image and then on the blue image while super-
imposed on the green image.
Start with the coarse convergence adjustments and finalize with the fine
convergence adjustment.
CONVERGENCE
G
R
E
EN
ONLY
RED ONGREEN
BLUE ON GREEN
Select with
then <ENTER>
<EXIT> to return
or
The screen area is divided into 25 areas.
23
22
4
9
25
24
5
15
17
16
3
8
1
14
2
Coarse Convergence Adjustments
Highlight ‘Red on Green’ under the coarse convergence item and press
ENTER. The coarse convergence menu will be displayed.
The following items are possible:
18
10
11
12
13
20
6
7
* Horizontal sides: adjust the vertical lines, within a certain area, on both
sides without influencing the lines on the middle of the image.
* Vertical corners: adjust the horizontal lines in the four corners, within a
certain area, without influencing the middle of the image.
Repeat for ‘blue on green’
19
21
CONVERGENCE
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
CONVERGENCE
Horizontal sides
Highlight “Horizontal lines’ and press ENTER to start the adjustment. To
make a coarse adjustment of the red or blue vertical lines in ZONE 3 and
5 simultaneously.
HORIZONTAL SIDES
VERTICAL CORNERS
B G R
B G R
Select with
then <ENTER>
<EXIT> to return
or
Hint
* Look to the outside edges of the image and adjust until the red or the blue
vertical lines are on the green lines or as close as possible to the green
lines.
CONVERGENCE
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
* During these adjustments, the horizontal convergence adjustments in
ZONES 2, 3, 4, and 5 will be set to midposition (barscale 50)
FINE ADJUSTMENT
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
6-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Random Access Adjustment Mode
Vertical corners
Highlight ‘Vertical corners’ and press ENTER to start the adjustment.
CONVERGENCE
HORIZONTAL SIDES
VERTICAL CORNERS
Select with
then <ENTER>
<EXIT> to return
or
To make a coarse adjustment of the red or blue horizontal lines in
zone 10, 14, 18 and 22 simultaneously.
Hint:
CONVERGENCE
- Adjust until the red or the blue horizontal lines are on the green lines
or as close as possible to the green lines.
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
- During these adjustments, the horizontal convergence adjustments
in zones 10 to 25 will be set to midposition (barscale 50)
CONVERGENCE
SEL : select area
using
arrow keys
ADJ : adjust area
using
Fine Convergence Adjustments
arrow keys
Use these controls after coarse convergence adjustment to optimize
the convergence of the red and blue image on the green image.
Toggle between
SEL and ADJ
with <ENTER>
<ENTER> continue
<EXIT> to return
Use the control disk to make horizontal or vertical convergence
adjustments in the selected zone and then press ENTER to move the
box to another zone or EXIT to return to convergence menu.
ENTER toggles arrow keys between zone selection and zone adjust-
ment.
EXIT returns to convergence menu.
Note: The green convergence adjustments can be added as an
option. When these are available, always start with ‘green only’. This
option will also be indicated on the convergence menu.
Highlight first ‘Green only’ when available with the control disk and
press ENTER to display the convergence adjustment menu.
Continue with red on green and blue on green.
CONVERGE
ADJUSTMENT
70
6-14
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MODE
7
Starting up the Service mode.
Use the control stick to highlight ‘Service’ and then press ENTER.
Some items in the Service mode are password protected (when the
password function is active). Enter your password to continue. All
other password protected items are now also available if you stay in
the adjustment mode.
ADJUSTMENT MODE
Select a path from
below :
GUIDED
RANDOM ACCESS
INSTALLATION
ENTER continues to the Service Mode main menu.
EXIT returns to the Operational mode.
The service items are combined in two service menus. To switch from
the first to the second menu or vice versa, push the control stick for-
ward or backward to select ‘more...’
SERVICE MODE
Overview flowchart ‘Service’ mode.
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
12C DIAGNOSTICS
Select with
then <ENTER>
or
<EXIT> to return.
Overview flowchart ‘Service’ mode
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
Identification
Highlight ‘Identification’ with the control disc and press ENTER.
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE: operating
ENTER will start the selected item.
EXIT returns to the Service mode menu.
The ‘Identification’ screen gives information concerning :
- Projector address. To change the address of your projector, contact a
qualified service technician.
RUNCO
DTV - 992
- Software version.
Proj. address : 001
Soft. Version : 6.00
Config. :Ceiling
Front
- Configuration.
Possible installations :
* Front-ceiling
* Front-table
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
* Rear-ceiling
* Rear-table
- Baud rate PC : transfer speed for communication with an IBM PC (or
compatible) or MAC. The baud rate of the projector must be the same
as the baud rate of the connected computer. When there is a differ-
ence, contact a qualified service technician to make the appropriate
changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator
will be displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
The status can be changed by pressing the ‘TEXT’ key once on the
RCU.
- Serial no. : indicates the fabrication number of the projector. This
number can be useful when calling for technical assistance.
Copy a block
The copy a block function copies the settings of a selected block into
the active block.
Highlight copy a block with the control disc and press ENTER.
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
ENTER will select the highlighted item.
EXIT returns to the Path Selection main menu.
ADJUST returns to the Operational mode.
COPY MODE
Nr. Src Fh Fv inp
conf
1
2
1
3
15.6 50 video FC
31.2 60 RGB3S RT
To copy the settings of a closed block to the block you are working on
(active block), use the control disc to select a block.
COPY BLOCK
All existing settings will be overwritten with the new settings.
Press ENTER to copy the selected block. A confirmation screen will be
displayed.
If you are certain you wish to copy the contents of the selected block into
the active block, press ENTER.
All settings
in current block
will be overwritten !
ENTER displays a confirmation screen.
EXIT returns to the Service Mode main menu.
Select with
then <ENTER>
or
<EXIT> to return.
EXIT cancels the copy procedure and returns without copying the block.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
Deletion of blocks
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
This item is password protected.
The delete function is used to clear all data (settings) from an adjustment
block.
A delete can be given :
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
- block by block
or
- for all blocks.
DELETE MODE
Deleting block by block
Nr. Src Fh Fv inp conf
The ‘delete a block’ function deletes the settings of a selected block.
1
2
3
4
5
6
1
3
-
2
-
15.6 50 video
31.2 60 RGB3S
15.6 50 intern
31.5 50 RGB3S
33.7 60 intern
FC
RT
FC
FC
FC
ENTER will select the pointed item.
EXIT returns to the Path Selection main menu.
ADJUST returns to the Operational mode.
DELETE BLOCK
Highlight ‘Delete a block’ with the control disc and press ENTER.
Push the control disc up or down to select the desired adjustment block.
The selected block
will be deleted !
ENTER displays the confirmation menu.
EXIT returns to the Service Mode main menu.
<ENTER> to confirm
<EXIT> to cancel
Press ENTER to delete the selected adjustment block. A confirmation
menu will be displayed.
ENTER will delete the selected block.
EXIT cancels the deletion procedure and returns to the Service mode main
menu.
ENTER gives a confirmation message before deleting.
EXIT returns to the Path Selection main menu.
MEMORY MANAGEMENT
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
DELETE ALL BLOCK
Deletion of all blocks
Highlight ‘delete all blocks’ with the control disc and press ENTER.
If you are certain you wish to delete all blocks, press ENTER to confirm,
otherwise press EXIT to return.
Once ENTER is pressed, all block headers and adjustment settings are
permanently removed and cannot be restored.
All block
will be deleted !
<ENTER> to confirm
<EXIT> to cancel
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
Change password
PROJECTOR SET-UP
This item is password protected.
Highlight ‘Change Password’ with the control disc and press
IDENTIFICATION
TOTAL RUN TIME
ENTER.
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE: operating
ENTER gives a confirmation message before deleting.
EXIT returns to the Path Selection main menu.
CHANGE PASSWORD
The current password is displayed. The new password must consist
of 4 digits between 0 and 9. Push the control disc to the left or to the
right to select the digits to be changed. Use the numeric keys to
enter the new digits.
Enter new password :
0 0 0 0
Press ENTER to save the new password. Before saving the new
password, a confirmation screen will be displayed.
Press EXIT to return to the Projector Set-up menu without saving the
new password.
When the displayed password is correct, press ENTER to save.
If not correct, press EXIT to cancel the saving.
CHANGE PASSWORD
Password will be
reprogrammed as XXXX
ENTER saves the entered password.
EXIT returns without saving.
<ENTER> to confirm
<EXIT> to cancel
Change Language
The ‘Change Language’ function offers the possibility to change the
language of the screen menus to :
PROJECTOR SET-UP
- English
- Spanish
- French
- German
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
Highlight ‘Change Language’ with the control disc and press
LANGUAGE
ENTER saves the entered password.
EXIT returns without saving.
ENGLISH
ESPANOL
~
FRANCAIS
DEUTSCH
ENTER.
Push the control disc up or down to select the desired language and
press ENTER to change the language.
Select with
then <ENTER>
or
<EXIT> to return.
Total Run Time
Highlight ‘Total Run Time’ with the control disc and press ENTER to
display the amount of time the projector has played since its first
start up at the factory.
PROJECTOR SET-UP
ENTER gives the selected item.
EXIT returns to Service mode menu.
ADJUST returns to the Operational mode.
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE: operating
Note : all projectors leave the factory after a burn-in period of
approximately 100 hours.
Select with
then <ENTER>
or
<EXIT> to return.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
All settings to midposition
Item is password protected.
MEMORY MANAGEMENT
Highlight ‘All settings to midposition’ with the control disc and press
ENTER to set all settings to their midposition.
A confirmation menu will be displayed first.
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
ENTER displays a Confirmation screen.
EXIT returns to the Service menu.
SET TO MIDPOSITION
ENTER will set all settings to their midposition. EXIT cancel the operation
to set all settings to their midposition.
All settings
on current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
Undo all settings to midpos
MEMORY MANAGEMENT
When “all settings to midpos” is selected, all settings are set to their mid-
position. To cancel this action, select ‘Undo all settings to midpos’ by push-
ing the control disc up or down and press ENTER. ‘Undo all settings to
Midposition’ is displayed in the Memory management menu instead of ‘All
settings to midposition’ when this latter is pressed.
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
UNDO ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
An undo is possible as long as the projector is playing on the same source
(= same adjustment block) even when some adjustments as geometry or
convergence are already readjusted. When undo is pressed all settings are
reset to the previous settings.
Select with
then <ENTER>
or
<EXIT> to return.
R & B convergence mid
MEMORY MANAGEMENT
Item is password protected.
Highlight ‘R & B convergence mid’ with the control disc and press ENTER
to set all convergence settings to their midposition. A confirmation screen
will be displayed first.
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
ALL SETTINGS TO MIDPOS
R & B CONVERGENCE MID
GR CONVERGENCE MID
ENTER sets the convergence settings to their midposition. EXIT cancels
the procedure to set the convergence settings to their midposition.
R & B CONVERGENCE MID
Convergence settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
Undo R & B convergence mid
When “R & B convergence mid” is selected, all convergence settings are
set to their midposition. To cancel this action, select ‘Undo R & B conver-
gence mid’ by pushing the control disc up or down and press ENTER.
‘Undo R & B convergence mid’ is displayed in the Memory management
menu instead of ‘R & B convergence mid’ when this latter is pressed.
An undo is possible as long as the projector is playing on the same source
(= same adjustment block) even when some adjustments are already read-
justed. When undo is pressed all settings are reset to the previous settings.
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
Dynamic Astigmatism (spot shape adjustment)
1
4
6
2
7
3
5
8
The spot shape adjustments correct the spot shape in 8 different
areas on the screen and that for the three colors separately. The
spot shape is adjusted according to the axial axises and the diago-
nal axises when using the arrow keys on the RCU.
Spot Shapes
before dynamic
astigmatism correction
These adjustments have to be done on a dot pattern (e.g. the inter-
nally generated pattern) with standard line frequency (15 kHz). The
adjustment values are stored in the EEPROM and remain the same
for all frequencies.
Diagonal
Spot Shapes
astigmatism correction
(use the
and
arrow key)
after dynamic
astigmatism correction
Follow the next procedure:
Axial
astigmatism correction
(use the
arrow key)
and
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
Highlight ‘Dyn. Astigmatism’ by pushing the joy stick forward or
backward and press ENTER to select.
DELETE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
EXIT returns to the path selection main menu.
SET TO MIDPOSITION
CONVERGENCE MIDE
DYNAMIC ASTIGMATISM
MORE...
Select the source type, selected source or genlock pattern, by high-
lighting the color for which the spot shape has to be corrected and
press ENTER.
e.g. when selecting RED under ‘on genlocked pattern’, the projec-
tor switches to a genlocked pattern.
DYNAMIC ASTIGMATISM
ON SELECTED SOURCE
R
ED
GREEN
BLUE
ON GLENLOCKED PATTERN
RED
GREEN
BLUE
S
e
le
c
t
p
a
tt
e
rn
o
r
c
o
lo
r
with or
then <ENTER>
<EXIT> to return.
Press ENTER to continue adjustment.
Increase the contrast level using the Contrast Control to near maxi
mum. Using that “+” Sharpness Key, defocus the image until the
dots are large and easily visible. Press ENTER to continue to SEL.
DYNAMIC ASTIGMATISM
SEL : select the adjustment area on the screen where the spot
shape has to be corrected.
Use the arrow keys to select one of the 8 areas. Press ENTER to
continue to ADJ.
First adjust the defocusing
of the image.
SEL : select area using arrow keys
ADJ : adjust axial astigmatism
using
or
, diagonal
astigmatism using
ADJ : adjust the spot shape in the axial or diagonal direction when
using the arrow keys for the selected area. Adjust until the spot
shape is circular.
Toggle between SEL and ADJ
with <ENTER>
<ENTER> to continue
<EXIT> to return.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
G2 Adjustment
Item is password protected.
COMMON SETTINGS
Highlight ‘G2 adjust’ with the control disc and press ENTER to con-
tinue.
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
MEMORYBANKS : ON
A safety notice will be displayed on the screen as it is necessary to
open the top cover to adjust the G2.
Select with
then <ENTER>
or
<EXIT> to return.
ENTER selects the G2 adjustment.
EXIT returns to the Common settings menu.
ADJUST returns to the Operational mode.
COMMON SETTINGS
G2 ADJUSTMENT
CRT RUN IN CYCLE
PROJECTOR WARM UP
MEMORYBANKS : ON
Select with
then <ENTER>
<EXIT> to return.
or
‘G2 adjustment should be performed by RUNCO personnel, or
RUNCO authorized dealers’.
If you are qualified, press ENTER to continue. If not qualified, press
EXIT to return to the Common settings menu. Further description of
the G2 adjustment is given in the Installation manual.
CRT run in cycle
SERVICE MODE
The CRT run in cycle option can only be activated when memory
blocks on an internal # pattern are available. When one or more
such blocks are available, a flashing white image (5 sec on, 5 sec
off) is generated and that for 5 minutes on the first internal block. In
the next 5 minutes, a second internal block will be used to generate
the flashing white image. The image will also be shifted in a vertical
way to prevent a CRT burn in. To quit the CRT run in cycle option,
press EXIT.
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
12C DIAGNOSTICS
Highlight ‘CRT run in cycle’ with the control disc and press ENTER
to start.
ENTER selects the CRT run in cycle option.
EXIT returns to the Path Selection main menu.
Select with
then <ENTER>
<EXIT> to return.
or
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Mode
Projector warm up
COMMON SETTINGS
Highlight ‘Projector warm up’ by pushing the control disc up or down
and press ENTER to select the projector warm up menu.
G2 ADJUSTMENT
CRT RUN IN CYCLE
The ON/OFF option can be toggled with the ENTER key.
PROJECTOR WARM UP
MEMORYBANKS
When in the ON position (and the CRT run in cycle is OFF), the pro-
jector can start up with a warm up period of 20 minutes. During the
start up a warm up menu will be displayed. This menu offers the pos-
sibility to skip the warm up period anyway by pressing the EXIT key
and offers the possibility to adjust the horizontal and vertical ampli-
tude of the white image with the control disc. During this warm up
period, a full white image is shifted on the CRT faceplate to avoid a
burn in.
Select with
then <ENTER>
<EXIT> to return.
or
Every 30 seconds a text box will be displayed on another place on
the screen with the remaining time to go.
PROJECTOR WARM UP
OPTION : ON
When EXIT is pressed during this warm up period, the warm up
menu will be redisplayed with the remaining time indication. Press
another time EXIT to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the projector, it
starts immediately with the projection of the selected source.
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES AT POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
TOGGLE OPTION ON OR OFF
CRT Drive Mode
with <ENTER>
<EXIT> to return
The projector CRT’s can be driven with the normal current (normal
mode), a lower current (economic mode) or with a higher current
(boost mode).
To change the drive mode, highlight ‘CRT drive mode’ by pushing
the control stick forward or backward and press ENTER to display
the CRT drive mode menu.
To change the boost mode, push the control stick forward or back
ward to select a display mode and press ENTER to select.
The following modes are available:
- normal
- economic : lower drive current to the CRT’s, the lifetime of the
CRT’s will enlarge but the light output will reduce.
- temporary boost: higher drive current to the CRT’s, the lifetime of
the CRT’s will shorten but the light output will be higher. This situa-
tion is temporary, when restarting the projector, the drive mode is
automatically set to normal.
- permanent boost: higher drive current to the CRT’s, the lifetime of
the CRT’s will shorten but the light output will be higher. This set-
ting will be saved in the EEPROM. When restarting the projector, it
will start up in boost mode.
A warning, permanent BOOST mode in use, will be displayed to
inform the user.
When text is on, this warning will be repeated every time a new
source is selected.
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
MESSAGES, WARNINGS, AND FAILURES
8
When selecting a new source,
The input is a valid input but
the source is not connected
to the input terminals or the
input source is switched off.
SOURCE 01
Fh= 15.6 kHz
Fv= 050 Hz
WARNING:
source not available
information about this source will be
displayed on the screen. Source
number, horizontal and vertical
frequencies of the displayed source.
Announcement of the selected
source.
When a wrong key is
pressed on the RCU.
SOURCE 01
Fh= 15.6 kHz
Fv= 050 Hz
WARNING:
invalid
key entry
Message to enter your password.
Password contains 4 digits.
Message when the entered
pass word is wrong.
enter password
xxxx
WARNING:
invalid
code entry
These messages will be displayed
on the screen when pushing the
<TEXT> key.
End of adjustment range.
text on
WARNING:
end of adjust range
Text ON : the `bar scale indication'
will be enabled during the change
of an analog control in the
`operational mode'+ all warnings
and failures will be displayed.
Text OFF : the `barnacle indication'
will be disabled during the change
of an analog control in the
`operational mode's all warnings
and failures will not be displayed.
Message will be displayed
when the input source is no
longer available. The
following message then
appears: `check input signal
or select new source'.
WARNING:
input no longer
available
text off
Indication of the projector ad dress
when activating the `AD DRESS'
button on the RCU with a pencil or
other small object.
This message will be
displayed after the message
`input no longer available'. It
asks to check the
connections between the
source and the projector or
to check if the source is
switched on.
PROJECTOR
ADDRESS:
003
check input signal
or select
new source
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages, Warnings, and Failures
The entered frequency or
applied frequency of the
source is out of the
Hardware failure. Call a
qualified service technician.
WARNING:
invalid
frequency input
FAILURE
RWI communication
error
projector's range.
Adjustment settings are lost.
Re load using Projector
Control Soft ware via PC or
MAC (if this option is
available), or readjust
image.
Communication error between
EYE-Q and the projector.
Call a qualified service
technician.
WARNING:
default
settings loaded in the
E2PROM
FAILURE
EYE-Q communication
error
Message to inform that
selected table is deleted.
This message will be
followed by `confirm
message?,on which the user
has to answer.
Message during the start up
of the EYE-Q. Message will
disappear when the EYE-Q
is ready to accept commands.
WAIT
starting
up EYE-Q
table is
deleted
Wrong software version in
your projector. Call for
technical sup port.
FAILURE
invalid RWI soft
version
Hardware failure. Call a
qualified service technician
for repair.
FAILURE
12C error
addr. : 7FH3
Hardware failure. Call a
qualified service technician
for repair.
FAILURE
short
circuit on 12C bus
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
DTV-992
DTV-992 ULTRA
Scan Rate:
Scan Rate:
15—75 KHz (horizontal)
37—200 Hz (vertical)
15—110 KHz (horizontal)
37—200 Hz (vertical)
Bandwidth:
CRTs:
75 mHz
Bandwidth:
CRTs:
120 mHz
8 High performance with
Electromagnetic focus
8 High performance with
Electromagnetic focus
Lenses:
Fully color corrected and
filtered HD-8 lenses
Lenses:
Fully color corrected and
filtered HD-8 lenses
Optical Resolution:
Inputs:
10 line pairs/mm
Component/RGB
Optical Resolution:
Inputs:
10 line pairs/mm
Component/RGB
Color Balance:
3200K, 5400K, 6500K,
9300K, Custom
Color Balance:
3200K, 5400K, 6500K,
9300K, Custom
Convergence
Memories:
Convergence
Memories:
32
32
Light Output:
Picture Size:
1250 lumens/230 ANSI
5—20 ft. wide
Light Output:
Picture Size:
1250 lumens/230 ANSI
5—20 ft. wide
Throw Distance:
1.33 x width (widescreens)
1.40 x width (4:3 screens)
Throw Distance:
1.33 x width (widescreens)
1.40 x width (4:3 screens)
Video Standards:
Configurations:
Contrast Ratio:
Convergence:
Power input:
NTSC, PAL, SECAM, NTSC 4.43
Front or Rear, Floor or Ceiling
100:1
Video Standards:
Configurations:
Contrast Ratio:
Convergence:
Power input:
NTSC, PAL, SECAM, NTSC 4.43
Front or Rear, Floor or Ceiling
100:1
Dynamic geometry, 25 point zone
115 VAC, 50/60 Hz
Dynamic geometry, 25 point zone
115 VAC, 50/60 Hz
Power
Consumption:
Power
Consumption:
500 W
500 W
Environment:
Humidity:
Storage:
32—104° F (0—40°C)
0—90%, non-condensing
10—122° F (-12—50°C)
Environment:
Humidity:
Storage:
32—104° F (0—40°C)
0—90%, non-condensing
10—122° F (-12—50°C)
Cabinet
Dimensions:
Cabinet
Dimensions:
Width: 23.25in./590.55 mm
Depth: 43 in./1092.20 mm
Height: 14.25 in./361.95 mm
Width: 23.25in./590.55 mm
Depth: 43 in./1092.20 mm
Height: 14.25 in./361.95 mm
Weight:
156 lbs. (70.76 kg)
Weight:
156 lbs. (70.76 kg)
Safety Regulations:
Complies with: UL, FCC
Class B , CE, C-Tick
Safety Regulations:
Complies with: UL, FCC
Class B , CE, C-Tick
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 1
RS 232 Control
By far, the most accurate way to control or integrate the DTV-992 / 992 ULTRA into a home theater system is by RS
232 control. In this section, you will find hardware configuration and how to format the control data, command strings
and examples.
Hardware Configuration
RS232 Connector 9PIN D-SUB PC-AT TYPE. Projector has female type.
To establish communications with the projector, the following conditions must be made:
3
2
5
8
6
3
TXD
RXD
GND
+9V
TXD
RXD
GND
CTS
DSR
PIN OUTS FOR 9 PIN
Recommended
Method
2
5
8
1:
2:
3:
4:
5:
6:
7:
8:
9:
CD
Carrier Detect
RXD Receive Data
TXD Transmit Data
DTR Data Term Ready
GND Signal Ground
DSR Data Set Ready
RTS Request To Send
CTS Clear To Send
Ring Indicator
Pin to Pin
All 9 Pins
6
+9V
NOTE: All wires are straight through. DO NOT cross PINS 2 to 3 as in a null
modem configuration.
Alternatively, the connections can be made as follows (absolute minimum of wires):
The Protocol Necessary
For Communications:
3
2
5
8
6
4
3
TXD
RXD
GND
+9V
TXD
RXD
GND
CTS
DSR
DTR
No Flow Control
2
5
8 Data Bits, No Parity, 1 Stop Bit
Jump Pins
4,6,8 at PC
side
Tied together
at computer
Baud Rate is selectable between 8
rates at the projector up to 9600
Baud (9600 is default).
+9V
NOTE: Some automation systems may only use/require pins 3, 2, 5 be connected.
How to format the control data
Every command sent to the projector is a group of 9 bytes that is called a record.
Even a simple ON command is sent as a record. Below is an explanation of the syn-
tax of a record. It is not necessary to memorize the syntax since the next section
contains a chart of strings that work with any DTV-992 / 992 ULTRA and can be
entered directly into most automation systems to control all the functions of the pro-
jector.
APP-1
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 1
Sending a RECORD (single instruction)
A RECORD consists of 9 bytes of information in the following order:
STX, OFFS, ADR, CMD, DAT1, DAT2, DAT3, DAT4, CHKS
Where:
STX
- 02H
Make projector(s) listen for its (their) unique address.
OFFS
- (1-255)
Offset you choose so that none of the data or CMDs - 02H (STX).
Normally set the offset to 0.
ADRe - (1-255)
Number corresponding to projector’s unique address (see dip switch setting).
If you are unsure of your projector’s address, set this to 0.
It will talk to your projector regardless of its address.
CMDe - (1-255)
The command to be sent to the projector (see list of commands).
See command list for all possible functions.
DAT1e - (1-255)
DAT2e - (1-255)
DAT3e - (1-255)
DAT4e - (1-255)
Additional data to be sent (set to 0 if not used)
Additional data to be sent (set to 0 if not used)
Additional data to be sent (set to 0 if not used)
Additional data to be sent (set to 0 if not used)
CHKSe - (ADR + CMD + DAT1 + DAT2 + DAT3 + DAT4) mod 256 - add everything and keep
only 2 right most digits
Note: Bytes from ADR to CHKS are shown in bold with the suffix ‘e’ to indicate the offset is added before sending the
byte.
APP-2
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 1
Example string to send to the projector with address 3 to turn it on/off
In decimal values
STX Offest ADRe CMDe DATle DAT2e DAT3e DAT4e CHKSe
4
4
2
4
7
18
4
4
21
Optional data bytes plus
offset. No data needs to be
sent to turn on projector
therefore these are equal to
zero and offset is then
added.
Always 2
Wake up projo
You choose offset. This is added to the
rest of the bytes so that none of them equal
2 which would make the projector think its
being told to wake up again. Normally
this is 0. It is set to 4 in this working example
to show how it affects the value of the rest
of the bytes.
Add bytes from ADR to DAT4, keep 2
right most digits, then add offset.
(3+14+0+0+0+0)+4=CHKSe
Command plus offset.
(14+4)
Address of
projector plus
offset.
COMMAND CODE LIST
Transmitting the following codes is the same as using the keys of the IR remote.
ENTER
EXIT
ADJUST
TEXT
07h (7)
08h (8)
09h (9)
0Dh (13) Menus On/Off
0Eh (14) Power On/Off
10h (16)
11h (17)
12h (18)
13h (19)
14h (20)
15h (21)
16h (22)
17h (23)
18h (24)
19h (25)
Enter button
Exit button
Adjust button
CUR_UP
CUR_DN
CUR_RI
CUR_LE
CON_UP
CON_DN
BRI_UP
BRI_DN
SAT_UP
SAT_DN
HUE_UP
HUE_DN
SHA_UP
SHA_DN
21h (33) Cursor up
22h (34) Cursor down
23h (35) Cursor right
24h (36) Cursor left
28h (37) Contrast +
29h (38) Contrast -
2Ah (42) Brightness +
2Bh (43) Brightness -
2Ch (44) Color +
2Dh (45) Color -
2Eh (46) Tint +
2Fh (47) Tint -
36h (54) Sharpness +
37h (55) Sharpness -
STDBY
NUM_0
NUM_1
NUM_2
NUM_3
NUM_4
NUM_5
NUM_6
NUM_7
NUM_8
NUM_9
*
Numeric
Keypad
The STDBY is a toggle for power ON/Off. If discreet
Power On of Power Off commands are necessary please
see the chart of example strings.
*
Decimal Value in ( ).
*
APP-3
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 1
COMMAND
BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8 BYTE 9
POWER ON/OFF
POWER ON
POWER OFF
$02
$02
$02
$00
$00
$00
$00
$00
$00
$0E
$51
$51
$00
$0A
$0A
$00
$00
$00
$00
$00
$00
$00
$01
$00
$0E
$5C
$5B
ENTER
EXIT
ADJUST
TEXT ON/OFF
CURSOR UP
CURSOR DOWN
CURSOR LEFT
CURSOR RIGHT
$02
$02
$02
$02
$02
$02
$02
$02
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$07
$08
$09
$0D
$21
$22
$24
$23
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$07
$08
$09
$0D
$21
$22
$24
$23
BUTTON 0
BUTTON 1
BUTTON 2
BUTTON 3
BUTTON 4
BUTTON 5
BUTTON 6
BUTTON 7
BUTTON 8
BUTTON 9
$02
$02
$02
$02
$02
$02
$02
$02
$02
$02
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$10
$11
$12
$13
$14
$15
$16
$17
$18
$19
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$10
$11
$12
$13
$14
$15
$16
$17
$18
$19
CONTRAST +
CONTRAST -
BRIGHTNESS +
BRIGHTNESS -
COLOR +
COLOR -
TINT +
TINT -
SHARPNESS +
SHARPNESS -
$02
$02
$02
$02
$02
$02
$02
$02
$02
$02
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$28
$29
$2A
$2B
$2C
$2D
$2E
$2F
$36
$37
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$28
$29
$2A
$2B
$2C
$2D
$2E
$2F
$36
$37
The $ sign indicates a hex value and may not be required by your automation system.
Remember that each command requires 9 bytes be sent to the projector. For example, to send
a power on command from a Phast Landmark Control system, enter the following string pre-
cisely as printed:
$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C
Use no spaces between the commas.
APP-4
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 2
TM
EYE-Q Autoconvergence
OVERVIEW
TM
The EYE-Q auto-convergence system allows for faster and more accurate convergence when used by the installer upon
TM
initial installation. The EYE-Q system also allows the end-user to perform occasional convergence touch ups without
TM
having to learn the complex convergence procedure using the TOUCH-UP option in the EYE-Q menu. By doing so, the
end-user can be assured that the image quality is always at its best.
To work correctly, the installer must complete geometry (setting green only) for one source which is the reference geom-
etry. Every memory that is auto-converged after that will use the same geometry as the reference. In most applications,
however, multiple aspect ratios are to be converged, each with its own unique geometry. In this case, the geometry for
TM
each aspect ratio needs to be completed first, the EYE-Q will converge the red and blue colors to the green for each
aspect ratio.
The last step is for the installer to touch-up the convergence using the fine convergence using the fine convergence adjust-
TM
ments for the red and the blue. The EYE-Q
is typically 95% accurate when doing a FULL AUTOCONVERGENCE
TM
adjustment, depending on screen size and how well the initial EYE-Q setup was performed.
TM
THE QUICK GUIDE to using the EYE-Q system:
Do geometry for the current memory bank (see geometry section)
TM
Focus the lens in EYE-Q SETUP menu
TM
Center the camera in EYE-Q SETUP menu
Set blanking for each edge. See GEOMETRY section.
Select AUTO-CONVERGENCE then ALIGN on current source from the EYE-Q menu
TM
If all five steps were completed successfully, the projector will have already begun to converge red and blue automatical-
ly at this time. Please read further for detailed instructions of each adjustment.
APX-1
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX 2
Easy-to-use, high precision automatic convergence system
Various options on the menu offer you the solution for your
own individual needs:
Align: convergence starts for the current image situa-
tion
Align from mid-position: convergence starts from mid-
position.
Touch-up: convergence starts when the source switch-
es or after a user-defined time: alignment of static con-
vergence is almost invisible for the audience.
Easy-to-use, high precision automatic geometry system
Various options on the menu offer a comprehensive solution
to your geometry requirements:
Quick auto-picture: aligns geometry within 45 sec-
onds.
Full auto-picture: aligns geometry very accurately fol-
lowed by auto convergence. This option offers a very
powerful adjustment tool.
Note: Must have a reference geometry set up first for these
options.
Compact, built-in system
A very compact, monochrome CCD camera
Use of Sub-Pixel Resolution Techniques, a state-of -the -art
proprietary Digital Signal Processing System.
TM
Preparing your EYE-Q
TM
When the lens of the EYE-Q is covered with the lens pro-
tection cap, ensure to remove this cap first before starting the
TM
adjustment procedure for the EYE-Q .
APX-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
ON- SCREEN OPERATING INSTRUCTIONS
TM
ACCESS TO EYE-Q ON-SCREEN MENUS
TM
After the EYE-Q unit has been correctly installed in the pro-
ADJUSTMENT MODE
jector, press the <ADJUST> button on the RCU (Remote
Control Unit) or the local keypad of the projector to enter the
‘Adjustment mode’
Select a path from below:
EYE-Q
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
TM
(please refer to the projector Owner’s Manual). The EYE-Q
path will be displayed in the menu:
Source 1
TM
Highlight EYE-Q by pushing the
control disc (on RCU).
or
keys of the
Select with
then <ENTER>.
<EXIT> to return
or
TM
Press the <ENTER> button to enter the EYE-Q menu.
TM
EYE-Q MENU
TM
TM
The EYE-Q menu will be displayed after the path EYE-Q
is selected. Six items are available:
EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
TOUCHUP.
EYE-Q DIAGNOSTICS
AUTOCONVERGENCE.
QUICKAUTOPICTURE.
FULLAUTOPICTURE.
Select with
then <ENTER>.
<EXIT> to return
or
TM
EYE-Q SETUP.
TM
EYE-Q DIAGNOSTICS.
TM
Choose EYE-Q SETUP first to carry out the SETUP proce-
dures.
TM
TM
Use EYE-Q DIAGNOSTICS to check whether the EYE-Q
is functioning normally.
APX-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TM
EYE-Q SETUP
EYE-Q
TM
The EYE-Q SETUP procedure needs to be done only once
after projector is correctly installed or whenever the projector
is reinstalled in another position.
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
TM
To enter the EYE-Q SETUP menu:
TM
Highlight EYE-Q by pushing the
control disc.
or
keys of the
Select with
or
then <ENTER>.
<EXIT> to return
Press the <ENTER> button to set the correct projector
configuration.
Setting the Configuration
EYE-QTM SETUP
When using a rear screen projector, this option must be set
to rear. Follow the steps described below to set the right con-
figuration:
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
TOUCH-UP OPTIONS:
Highlight FRONT (or REAR) by pushing the
of the control disc.
or
keys
Select with
or
then <ENTER>.
<EXIT> to return
Press the <ENTER> button to set the correct projector
configuration.
TM
The EYE-Q SETUP menu provides you with easy to use
methods to focus the camera lens and to center the camera.
Please pay attention while doing it, as a properly
focused camera lens and correctly centered camera are
prerequisites for a perfect automatic convergence.
APX-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
FOCUSING THE CAMERA LENS
EYE-Q
The lens of the camera must be focused properly on the pro-
jection screen. Follow the steps described below:
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
TM
In the EYE-Q SETUP menu, highlight FOCUS THE
LENS by pushing the up or down keys of the control
disc.
EYE-Q DIAGNOSTICS
Se
t
<E
Press the <ENTER> button to start up the process.
EYE-Q SETUP
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
TOUCH-UP OPTIONS:
A pattern of horizontal alternating green/black bars will be
projected onto the screen, together with a textbox. Inside the
box, the text “CAMERA FOCUS” indicates the item subject to
adjustment and under the text, a numeric bar scale (from 0
to 99) will visualize the correction.
Select with
or
then <ENTER>.
<EXIT> to return
To obtain a correctly focused camera, turn the lens until max-
imum readout. The value of the stabilized maximum read-
out will be in the range between 60 and 90, depending on
ambient light.
In rear projection, the maximum value can be less than 60
dependent on ambient light.
After finishing the correction, press the <EXIT> button to
TM
return to the EYE-Q menu
CAMERA
FOCUS
50
APX-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
CENTERING THE CAMERA
EYE-Q
The camera must be centered in middle of the projection
screen. Follow the steps described below:
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
Highlight CENTER CAMERA by pushing the up or
down keys of the control disc.
EYE-Q DIAGNOSTICS
EYE-Q SETUP
Press the <ENTER> button to start up the process.
Note: It is critical that the green raster of the presently select-
ed source is centered on the CRT faceplate. Other-
wise, the camera will not be centered properly.
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
TOUCH-UP OPTIONS:
Select with
or
then <ENTER>.
<EXIT> to return
CENTERING THE CAMERA HORIZONTALLY
One vertically centered green bar will be projected onto the
screen, together with a text box. Inside the box, the text of
“CAMERA ALIGNMENT HORIZONTAL” indicates the item
subject to adjustment and a symmetrical bar scale (from -50
to +50) under text.
CAMERA
ALIGNMENT
HORIZONTAL
If the indicated value below the bar scale is not equal to zero
(i.e. the black highlight is not in the middle of the bar scale),
the camera is not centered horizontally. Follow the steps
below to center the camera horizontally:
+00
Turn the knob situated on the upper-right corner of the cam-
era clockwise or counter clockwise until the highlight is in the
middle of the bar scale (i.e. the indicated value becomes
zero);
Fixed screw
No Adjustment
Press the <ENTER> button to continue with the camera ver-
tical centering.
Note: An easy way to remember the H+V adjustments is:
The knob located up/down from the fixed screw is ver-
tical adjustment. The knob located left/right from the
fixed screw is horizontal adjustment.
Knob for centering
the camera vertically
Knob for centering
the camera
horizontally
APX-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
CENTERING THE CAMERA VERTICALLY
One horizontally centered green bar will be projected onto
the screen, together with a text box. Inside the box, the text
of “CAMERA ALIGNMENT VERTICAL” indicates the item
subject to adjustment and a symmetrical bar scale (from -50
to +50) under the text.
If the indicated value below the bar scale is not equal to zero
(i.e. the black highlight is not in the middle of the bar scale),
the camera is not centered vertically. Follow the steps below
to center the camera vertically:
CAMERA
ALIGNMENT
VERTICAL
+00
Turn the knob situated on lower-left corner of the cam-
era clockwise or counter clockwise until the highlight is
in the middle of the bar scale (i.e. the indicated value
becomes zero).
After finishing the vertical centering, press the <ENTER>
button to return to the EYE-QTM menu.
When installed in a retro projector, the centering procedure
is not necessary and not possible as the camera mounting is
fixed.
25
15
17
23
22
4
9
SET TOUCH-UP OPTIONS
24
5
16
3
8
1
14
2
For convergence purpose, the screen is divided into 25
areas. Every area has its unique number from 1 to 25.
Touch-up adjust the Area No. 1. This adjustment is also
called the “static convergence”.
18
19
20
21
6
7
10
11
12
13
The Touch-up can be set on Source or on Timer.
Touch-up on Source means when switching from one source
to another, the static convergence will be carried automati-
cally.
EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
Touch-up on Timer means whenever the user-defined period
of time has elapsed the static convergence will be adjusted
automatically.
EYE-Q DIAGNOSTICS
EYE-Q SETUP
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
Touch-up is an option the customer can use periodically after
a final install is complete. This will insure image quality is at
its best.
TOUCH-UP OPTIONS
ON SOURCE SWITCH : on/off
ON TIMER : on/off
-h.- min.
TOUCH-UP ON SOURCE ON/OFF
Follow the steps below to set the option ON/OFF:
Select with
then <ENTER>.
<EXIT> to return
or
Push up or down keys of the control disc to highlight ON
SOURCE SWITCH: off;
TM
Press the <EXIT> button to return to the EYE-Q menu.
APX-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TOUCH-UP ON TIMER
This option allows the static convergence to be carried out auto-
matically after a user-defined time, which can be programmed in
hours and/or minutes.
EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
To program the touch-up on Timer:
Push up or down keys of the control disc to highlight ON
TIMER: off;
EYE-Q SETUP
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
Press the <ENTER> button to switch it to ON and the pre-
set time will be displayed;
TOUCH-UP OPTIONS:
Press the <TEXT> button to enter the TOUCH-UP TIMER
menu;
TOUCH-UP OPTIONS
ON SOURCE SWITCH : on/off
ON TIMER : on/off
-h.- min.
Push left or right keys of the control disc to highlight the
digit to be changed;
with
<ENTER>.
to return
or
Use the numeric keys to enter a desire value;
EYE-Q SETUP
TM
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
Press the <ENTER> button to confirm and the EYE-Q
SETUP menu will return on the screen; or press the <EXIT>
button to leave the preset value untouched and return to the
TOUCH-UP OPTIONS:
TM
EYE-Q SETUP menu.
Select with
then <ENTER>.
<EXIT> to return
or
TM
Press the <EXIT> button to return to the EYE-Q menu.
When one adjust geometry by hand, a reference screen and a
reference pattern are required. There are a lot of possibilities for
a reference screen. A test pattern for a video test disc is nor-
mally used. See geometry section of manual for more informa-
tion. Once a selection of a reference screen and a reference pat-
tern is made, adjusting geometry is only a matter of converging
these two elements.
TM
EYE-Q requires a reference for adjusting geometry. The sim-
plest way to have a reference screen is to adjust one source by
hand, which then serves as a reference for all other sources.
TM
After adjusting a source, the reference is learned by EYE-Q
and stored in non-volatile memory. Having this Reference
TM
Source in memory EYE-Q can adjust all other sources to have
the same geometry as the Reference Source.
REFERENCE SOURCE
Before any geometric adjustment can be done, the user Must
learn a Reference Source. This process is ONLY DONE ONCE
since the Reference will be stored in non-volatile memory. If
however, the projector is moved from its position, then the Learn
Reference procedure must be repeated. After learning a Refer-
ence do not touch the camera (for focusing and centering).
If using multi-aspect ratios, a Reference Geometry must be done
for each aspect ratio.
ADJUSTING OTHER SOURCES
Once a Reference Source is in memory, other sources are
aligned with the same geometry as the Reference Source. If no
Reference Source is learned, the resulting geometry will be
unpredictable.
APX-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
LEARNING A REFERENCE
ADJUSTMENT MODE
Select a path from below:
Learning a reference needs only to be done when the EYE-Q is setting up
Geometry for the green. In typical applications, green geometry is completed
manually and EYE-Q is used to autoconverge red + blue colors to the green.
EYE-Q
GUIDED
RANDOM ACCESS
EYE-Q
TOUCH UP
AUTOCONVERGENCE
Adjust one Reference Source with perfect geometry. This source can have
either horizontal or vertical frequency. Remember that other sources will have
the same geometry as this Reference Source. This means that if a source has
4:3 aspect ratio, all sources will be adjusted with a 4:3 aspect ratio and the same
horizontal and vertical amplitudes.
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
EYE-Q SETUP
FOCUS THE LENS
CENTER THE CAMERA
CONFIGURATION: rear/front
LEARN REFERENCE
Follow the steps below to select:
TOUCH-UP OPTIONS:
TM
Enter in the Adjustment Mode and select EYE-Q by pushing up or down
keys of the control disc. Now select SETUP using the up or down keys,
finally select LEARN REFERENCE.
Select with
then <ENTER>.
<EXIT> to return
or
TM
EYE-Q will now project the Reference Source with horizontal green line insert-
ed at the top region and a horizontal green line inserted at the bottom region of
the image.
Pushing the up or down keys of the control disc adjust the horizontal green
line at the top until it matches the top edge of the Reference Source per-
fectly, then press <ENTER>.
Top Green Line
Top Edge
Using the up or down keys of the control disc adjust the horizontal green
line at the bottom until it matches the bottom edge of the Reference Source
perfectly, then press <ENTER>.
REFERENCE SOURCE
TM
Now EYE-Q projects the Reference Source with a vertical green line inserted
at the left and a vertical green line inserted at the right.
Pushing the up or down keys of the control disc changes the position of the
vertical green lines simultaneously; they are being shifted symmetrically
inward and outward with respect to the scan of the projector.
Bottom Green Line
Bottom Edge
Use left or right keys of the control disc to change the phase of the Reference
Source. Use both (up or down) or (left or right) so that the green vertical lines
perfectly match the right-left edges of the reference image, then press
<ENTER> (this will initiate the learning procedure).
Right Green Line
Right Edge
NOTE: If you had to use the left and right arrow keys to adjust the phase, this
means that the phase of the Reference Source was originally not adjusted cor-
rectly. Hence the Reference Source may now fall short of the physical screen.
To avoid this, re-adjust the Horizontal Raster Shift (in the Random Access
Adjustment mode, refer to Owner Manual) so that the Reference source falls on
the physical screen and repeat the Learn Reference selection.
REFERENCE SOURCE
Do not adjust the phase when repeating the Learn Reference procedure.
Left Edge
Left Green Line
Pressing<EXIT> will interrupt the Learn Reference procedure if required.
TM
WHAT IS BEING MEASURED BY EYE-Q
TM
Using the borderlines define above, EYE-Q
knows exactly when the image
TM
starts and stops with respect to time scale. EYE-Q is now able to project lines
at the edges. Using the border lines left and right, EYE-Q projects three ver-
TM
tical thick green lines at positions 5, 50 and 95%. Using the border lines top and
TM
bottom, EYE-Q projects three horizontal thick lines at positions 5, 50 and 95%.
TM
EYE-Q then calculates the intercepts of the three vertical and three horizontal
lines resulting in nine points. These nine points are the reference points for
other geometry sources and are stored into memory.
NOTE: “DELETE ALL BLOCKS” in the Service menu does not delete the Ref-
erence source parameters.
APX-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TOUCH UP AND AUTOCONVERGENCE
ADJUSTING SCREEN SIZE
Left
blanking
Top
blanking
In case the projection screen is not greater than the desired
size or the screen has a frame around it (i.e. projection
impossible outside the frame), the following blanking adjust-
ments have to be done before starting the automatic con-
vergence:
When using a video source: adjust the top, bottom, left
and right blanking until the whole projected image of
video is just still visible;
When using a screen with a frame: adjust the top, bot-
tom, left and right blanking until the whole projected
image is just still visible.
So that the selected screen area after blanking adjustments
corresponds with the projected image size.
In this way, the screen size is set correctly to ensure the suc-
cessful convergence.
Right
blanking
Bottom
blanking
NOTE:
For blanking adjustments, please refer to the Projector
Setup Manual.
To enter the AUTOCONVERGENCE menu:
Highlight AUTOCONVERGENCE by pushing up or
down keys of the control disc;
ADJUSTMENT MODE
Select a path from below:
EYE-Q
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Press the <ENTER> button.
Source 1
The AUTOCONVERGENCE menu allows the automatic
convergence either on the currently selected source or on all
sources (all filled memory blocks of the projector).
EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
ON CURRENT SOURCE
the on current source includes three options, the first of
which is selectable in the iris menu:
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
TM
Touch Up EYE-Q
ALIGN FROM MIDPOSITION
STATUS:
ready
Select with
then <ENTER>.
<EXIT> to return
or
Align
Align from midposition
APX-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TOUCH-UP
ADJUSTMENT MODE
Select a path from below:
When TOUCH-UP is selected, only the static convergence of
the currently selected source will be carried out automatical-
ly. Follow the steps below to select:
EYE-Q
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 1
Select with
then <ENTER>.
<EXIT> to return
or
Highlight TOUCH-UP by pushing up or down keys of the
control disc;
EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Press the <ENTER> button to start up the static conver-
gence.
Select with
or
then <ENTER>.
<EXIT> to return
If the process is successfully completed, the projector will
return to image display of the current source.
EYE-Q
ALIGN ON CURRENT SOURCE
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
When ALIGN is selected, the automatic convergence on the
current memory bank will be carried out automatically, start-
ing from the existing settings.
Select with
or
then <ENTER>.
<EXIT> to return
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
By projecting alternately red and blue line, 25 convergence
areas are aligned to the green pattern.
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
Select with
then <ENTER>.
<EXIT> to return
or
Follow the steps below to select:
Highlight ALIGN below ON CURRENT SOURCE by
pushing up or down keys of the control disc;
Press the <ENTER> button to start up the automatic
convergence of the entire screen.
If the process is successfully completed, the projector will
return to image display of the current source.
Use this option when the convergence is close to proper
alignment.
EYE-Q
TOUCH UP
ALIGN FROM MIDPOSITION ON CURRENT SOURCE
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
When ALIGN FROM MIDPOSITION is selected, the auto-
matic convergence on the current source will be carried out
automatically, but starting from the mid-position settings.
Select with
then <ENTER>.
<EXIT> to return
or
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
By projecting alternately red and blue lines, 25 convergence
areas are aligned to the green pattern.
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
Follow the steps below to select:
Select with
then <ENTER>.
<EXIT> to return
or
Highlight ALIGN FROM MIDPOSITION by pushing up or
down keys of the control disc;
Press the <ENTER> button to start up the automatic
convergence of the entire screen.
If the process is successfully completed, the projector will
return to image display of the current source.
Use this option when the convergence is far from proper
alignment.
APX-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
ON ALL SOURCES
EYE-Q
The “On all sources” functions as the “On current source.” It
includes also three options:
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Touch-up
Select with
then <ENTER>.
<EXIT> to return
or
Align
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
Align from mid-position
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
The difference is that the convergences will be carried out on
all sources of the projector, i.e. all available memory banks of
the projector. The total number of sources is displayed
between the brackets.
Select with
then <ENTER>.
<EXIT> to return
or
TOUCH-UP ON ALL SOURCES
EYE-Q
When TOUCH-UP below ON ALL SOURCES by pushing up
or down keys of the control disc;
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Press the <ENTER> button to start up the static conver-
gence.
Select with
then <ENTER>.
<EXIT> to return
or
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
The process will repeat for as many times as the total num-
ber of the sources until all sources are perfectly aligned.
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready/forced exit/forced break
If the process will repeat for as many times as the total num-
ber of the sources until all sources are perfectly aligned.
Select with
then <ENTER>.
<EXIT> to return
or
If the process is successfully completed, the projector will
return to image display of the current source.
ALIGN ON ALL SOURCES
When ALIGN is selected, the automatic convergence on all
sources will be carried out automatically, starting from the
existing settings.
EYE-Q
By projecting alternately red and blue lines, 25 convergence
areas are aligned to the green pattern. The process will
repeat for as many times as the total number of the sources
until all sources are perfectly aligned.
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Select with
then <ENTER>.
<EXIT> to return
or
Follow the steps below to select:
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
Highlight ALIGN below ON ALL SOURCES by pushing up or
down keys of the control disc;
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
Select with
then <ENTER>.
<EXIT> to return
or
Press the <ENTER> button to start up the automatic conver-
gence of the entire screen.
If the process is successfully completed, the projector will
return to image display of the current source.
Use this option when the convergence is close to proper
alignment.
APX-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
ALIGN FROM MIDPOSITION ON ALL SOURCES
EYE-Q
TOUCH UP
When ALIGN FROM MIDPOSITION is selected, the auto-
matic convergence on all sources will be carried out auto-
matically, but starting from the midposition settings.
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Select with
then <ENTER>.
<EXIT> to return
or
By projecting alternately red and blue lines, 25 convergence
areas are aligned to the green pattern. The process will
repeat for as many times as the total number of the sources
until all sources are perfectly aligned.
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
Follow the steps below to select:
Select with
or
then <ENTER>.
<EXIT> to return
Highlight ALIGN FROM MIDPOSITION below ON ALL
SOURCES by pushing up or down keys of the control
disc;
Press the <ENTER> button to start up the automatic
convergence of the entire screen.
If the process is successfully completed, the projector will
return to image display of the current source.
Use this option when the convergence if far from proper
alignment.
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
INTERRUPTING THE AUTOMATIC CONVERGENCE
PROCESS
ALIGN FROM MIDPOSITION
STATUS:
forced exit
Select with
then <ENTER>.
<EXIT> to return
or
The process of the above-mentioned automatic convergence
can be interrupted at any moment by pressing the <EXIT>
button.
After the <EXIT> button is pressed, the projector will leave
the automatic convergence process and a message will be
displayed informing of the action:
Status: Forced<EXIT>
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ERROR MESSAGES
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready/forced exit/forced break
The status line in the AUTOCONVERGENCE menu gives
three possible messages:
Select with
then <ENTER>.
<EXIT> to return
or
Ready: before automatic convergence starts;
Forced<EXIT>: when interrupting the process;
Forced break: error message.
Error messages are displayed when the automatic conver-
gence is not successfully completed.
APX-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
NO PATTERN ERROR
EYE-Q
TOUCH UP
After starting up the automatic convergence, the projector
will start to calculate and locate 5 horizontal and 5 vertical
lines which are used to divide the screen into 25 areas.
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
Select with
then <ENTER>.
<EXIT> to return
or
If the projector does not succeed in finding the pattern, it will
try two time. If the two attempts fail, the projector will quit the
process and display the Error menu.
Error occurred
check :
*lenscap removed
*focus camera
*center camera
*ambient light too high
*hardware problem : press <ENTER>
to start diagnostics
*blanking adjustments are correct
The AUTOCONVERGENCE selection will be followed by the
error window displaying the following possibilities.
Press <ENTER>. to start
EYE-Q diagnostics or <EXIT> to
return
Error occurred, please check:
the lens cap is removed
the lens of the camera is correctly focused;
the camera is correctly centered;
if hardware problems exist, do diagnostics;
the ambient light is too high;
the blanking adjustments are correct;
TM
Press the <ENTER> button to start EYE-Q diagnos-
TM
tics (refer to page for full details on EYE-Q diagnos-
tics, please note that this option may vary in selection
with different projectors).
STATUS REPORTING FORCED BREAK
After starting up the automatic convergence, if unexpected
trouble such as the interruption of source input occurs, the
projector will quit the process and display the AUTOCON-
VERGENCE menu on the screen.
The status line in the AUTOCONVERGENCE menu will dis-
play the following message:
Status: Forced break
The possible causes of such an error:
The source is disconnected during the convergence:
On the screen a message “Source not available” will be
displayed and projector waits until the source is recon-
nected or selected;
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
forced break
Select with
then <ENTER>.
<EXIT> to return
or
Switching sources during the convergence:
After the source is available again, the AUTOCONVER-
GENCE menu will be displayed the status line reporting
“Forced Break.”
APX-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TM
EYE-Q DIAGNOSTICS
EYE-Q
TM
This option allows a check-up of the EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
NOTE: Most errors that occur during the LEARN REFER-
ENCE procedure or the beginning of the AUTOCONVER-
GENCE procedure are caused by one of the following:
EYE-Q DIAGNOSTICS
Lens cap not removed
Lens focus not performed properly
Camera focus not performed properly
Ambient light is too high
TM
EYE-Q
Interferance Test TBD
DIAGNOSTICS
Generic Test TBD
Sync Test
Ram Test
TBD
TBD
Reference not learned properly
Blanking not set properly—must set blanking to each
edge of screen border
Ready and Config Test
If all else fails, run the diagnostics.
TM
To start up the EYE-Q Diagnostics:
TM
Highlight EYE-Q by pushing up or down keys of the
control disc;
Press the <ENTER> button.
TM
After the <ENTER> button is pressed, the EYE-Q DIAG-
NOSTICS menu will be displayed and the Tests start
instantly.
It includes check-ups on four items:
Interface Test;
Generic Test;
Sync Test;
Ram Test.
After completing each test, the status report will give the test
result:
Pass; or
Failed plus the error number.
During the Interface Test, the following messages will dis-
played one after another on the screen:
Ready and Config Test;
Ready and Config OK;
Config Ackn. Test;
Config Ackn. OK;
Full Config Test;
During the Generic Test, the following messages will be dis-
played one after another on the screen:
Config for Generic;
Config for Generic OK;
Chipselects Test;
Full Config OK;
Interface Test OK.
Chipselects OK;
Addressability Test;
Addressability OK;
Crystal and Reset Test;
Crystal and Reset OK;
Generic Test OK
In case of failures, the error message will be shown:
FAILED... Error 01; or
FAILED... Error 02; or
FAILED... Error 03;.
APX-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix 2
TM
In case of failures, the error message will shown:
FAILED... Error 11; or
If all the tests are successful, the EYE-EYE-Q
menu will be as follows:
FAILED... Error 12; or
Press the <EXIT> button to return to the EYE-™
FAILED... Error 13; or
FAILED... Error 14; or
EYE-QTM
Interferance Test PASS
DIAGNOSTICS
FAILED... Error 15.
During the Sync Test, the following messages will displayed
one after another on the screen:
Generic Test PASS
Sync Test
Ram Test
PASS
PASS
Config for Sync;
EYE-QTM
has been given
a clean bill of HEALTH.
Config for sync OK;
Horizontal Sync Test;
Horizontal Sync OK;
Vertical Sync Test;
Vertical Sync OK;
Frame and Field Test;
Frame and Field OK;
Sync Test OK.
In case of failures, the error message will be shown:
FAILED... Error 21; or
FAILED... Error 22; or
FAILED... Error 23; or
FAILED... Error 24; or
FAILED... Error 25; or
FAILED... Error 26; or
Sync Test Error 27
No syncs found
Check Camera & Cabling.
During the Ram Test, the following messages will displayed
one after another on the screen:
Config for Ram;
Config for Ram OK;
Ram Data Line Test;
Ram Data Lines OK;
Ram Address Lines Test;
Ram Address Lines OK;
Ram Full Content Test;
Ram Full Content OK;
Ram Test OK
In case of failures, the error message will be shown:
FAILED... Error 31; or
FAILED... Error 32; or
FAILED... Error 33; or
FAILED... Error 34.
APX-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
RUMA-003700 rev 10-00
2463 Tripaldi Way
Hayward, CA 94545
510-293-9154 Fax: 510-293-0201
Download from Www.Somanuals.com. All Manuals Search And Download.
|