OWNER’S OPERATING MANUAL
CL-510 / CL-510LT
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe
Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care,
you should enjoy many years of unparalleled video performance. Please read this consumerprotection plan
carefully and retain it with your other important documents.
This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal Trade
Commission Improvement Act.
WHAT IS COVERED UNDER THE TERMS OF THIS WARRANTY:
SERVICE LABOR: Runco will pay for service labor by an approved Runco service center when needed as a
result of manufacturing defect for a period of two (2) years from the effective date of delivery to the end
user.
PARTS (Not including projector lamp): Runco will provide new or rebuilt replacement parts for the parts
that fail due to defects in materials or workmanship for a period of two (2) years from the effective date of
delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion
(if any) of the original warranty period.
LAMP: Six months from the effective date of delivery to the end user.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS WARRANTY:
This warranty only covers failure due to defects in materials and workmanship that occur during normal use
and does not cover normal maintenance. This warranty does not cover cabinets or any appearance item;
failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper
installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage
due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit;
or damage that is attributed to acts of God. In the case of remote control units, damage resulting from
leaking, old, damaged or improper batteries is also excluded from coverage under this warranty.
CAUTION: DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR
SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. IT IS IMPERATIVE
THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED RUNCO
DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO ENSURE THAT
YOU ENJOY THE FINE PERFORMANCE YOUR RUNCO PRODUCT IS CAPABLE OF PROVIDING
WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the
warranty period. There are no express warranties. Runco also excludes any obligation on its part for
incidental or consequential damages related to the failure of this product to function properly. Some states
do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion
or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to
state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user.
For your convenience, keep the original bill of sale as evidence of the purchase date.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you
promptly if we should discover a safety problem or product update for which you must be notified.
TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:
Repairs made under the terms of the Limited Warranty covering your Runco International video product will
be performed at the location of the product, during usual working hours, providing location of product is
within normal operating distance from a Runco Authorized Service Center. If, solely in Runco’s judgement,
location of product to be repaired is beyond normal operating distance of the closest Runco Authorized
Service Center, it is the owner’s responsibility to arrange for shipment of the product for repair. These
arrangements must be made through the selling Runco dealer. If this is not possible, contact Runco directly
for a return authorization number and shipping instructions. Runco will return product transportation
prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be
the responsibility of the owner.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service location, or for additional
information about this warranty, please call, write or visit our website:
CUSTOMER SERVICE DEPARTMENT
RUNCO INTERNATIONAL
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777 / Fax: (510) 324-9300
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Runco CL-510/ CL-510LT Video Projector
User’s Manual
Thank you for your purchase of this quality Runco video projector! It has been designed to provide you with the quality
of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your
guide through the menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
CAUTION
uninsulated " dangerous voltage " within the product's
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this projector near water, outdoors or otherwise exposed to the elements.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the
replacement of the obsolete outlet.
9. Do not connect the RJ-11 RS-232 jack to a telephone line connection.
10. The 12V trigger outputs 12V DC for triggering. Do not connect to any other power input or output. This could
cause damage to this unit.
11. Only use accessories specified by RUNCO International.
12. Keep the packing material in case the projector should ever need to be shipped.
13. Unplug this projector during lightning storms or when it will not be used for an extended period of time.
14. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45
minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life.
Excessive operation of lamps beyond rated life could cause them to explode in rare occasions.
15. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any
way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Table of Contents
1.Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Projector Exterior View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front / Upper Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear / Bottom Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjust the Lens Zoom/Focus ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjust the height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Zoom/ Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Selecting Input Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PIP/ PBP function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Turning off the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2
WARNING
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
1. Overview
Features
■ Runco Engineered, Gen 3 Technology.
TM
■ Native 16x9 Aspect Ratio DMD
12 degree mirrors with dark metal process
■ High Contrast and Picture Quality
9 point white balancing system
■ Dynamic Performance and Rich Gray-scale
6-segment 5x color wheel and precision gray scale tracking
■ TIR (Total Internal Reflection) Prism
Light engine with custom optics featuring an elliptical aperture for highest performance.
■ Wide Variety of Inputs
This unit can support various video formats, including Composite, S-Video, Component, DTV Y/PB/PR, DTV RGB
and Computer signals. The HDTV input (DTV Y/PB/PR and DTV RGB) is input through RGB BNC connectors,
providing the least amount of signal degradation caused by longer cable runs.
■ HDTV Ready
480P, 1080i and 720P (576P PAL Version) formats are all compatible with this unit (via an external DTV decoder, not
provided).
■ De-interlacing with 3:2 Pull-down
Using Runco's proprietary De-interlacing technology, this projector provides exceptional scaling and film to video
(3:2 pulldown) conversion for the most artifact-free images possible.
■ PIP/ PBP function
Picture in picture/ Picture by picture functions allow you to display two inputs on the screen at the same time.
■ Video Memory
This projector allows the user to store up to three different settings per input.
1. Overview
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Projector Exterior View
■ Front / Upper Side
1. Front Lamp Cover
6. Focus Ring and Zoom Ring Access
Adjusts the focus and zoom of image.
Remove this cover when replacing the lamp. (See
7. Power LED and Lamp LED
2. Projection Lens
Show the status of power and lamp.
For more details, see "Control Panel" on page 5.
3. Front IR Sensor
8. Top IR Sensor
4. Ventilation Holes (intake)
5. Ventilation Holes (exhaust)
■ Rear / Bottom Side
1. Connector Panel
6. Front Adjusters
Adjust the height or projection angle
7. Ceiling Mount Holes
2. AC Power IN Socket
The connecting holes for ceiling mounting
device.
3. AC Power Switch
AC main power switch
8. Ventilation Holes (exhaust)
9. Cable Access Cover
4. Ventilation Holes (intake)
5. Rear Adjusters
Adjust the height or projection angle
4
1. Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Controls and Functions
■ Control Panel
1.
POWER LED
Indicate power status
■ Orange when the AC power cord is plugged into the wall outlet (standby mode). Once in the
standby mode, you can turn on the projector by pressing the ON key on the remote control for
ONE second.
■ Green when the power is turned on (operational mode).
■ Flashing Orange for the first 45 seconds after power-up indicating that the lamp is warming up.
■ Flashing Green for 90 seconds after the projector is powered off indicating that the lamp is cooling
down.
2.
LAMP LED
Indicates the status of lamp
■ Red when the lamp has developed a problem. Please contact your Runco Dealer for assistance.
3.
4.
ZOOM RING
Adjust the size of the image
■ Rotate right to enlarge the image, and rotate left to make the image smaller.
FOCUS RING
Adjust the focus of the image
■ Rotate the focus ring right or left to focus the image.
1. Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
■ Connector Panel
1. Video (RCA Jack)
Composite video signal input.
2. S-Video (mini DIN 4-pin)
Y/C (S-video) signal input
3. Component (RCA Jacks)
480i Component (Y/CB/CR) video signal input
4. RGB/ HDTV (BNC) or Progressive Scan DVD players
DTV Y/PB/PR or DTV RGB video signal input.
5. DVI/ HDCP
Digital/ Analog signal input.
6. RS-232C (RJ-11 Jack)
RS-232C control signal input.
7. 12v Trigger (mini jack with the diameter of 5.5 mm outside and 2.5 mm inside)
+12V output, active when the projector is turned on.
6
1. Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
■ Remote Control
ON
Hold down this button for ONE
second to turn on the unit.
OFF
Press this button to turn off the
unit.
Anamorphic
For 16: 9 DVDs.
M1, M2, M3, Default
Recall video memory sequentially
4 X 3
The input signal will be scaled to
fit 4: 3 display mode in the center
of screen.
LPos+, LPos-
Letterbox position
Color
Adjust color intensity
Letterbox
Letterbox mode. Image in letter-
box format is enlarged to fit 16:9
full screen display and the upper/
lower portion are “blanked off”.
Brightness
Adjust picture brightness
Contrast
Adjust picture contrast
VirtualWide
4:3 image is enlarged nonlinearly
in horizontal direction to fit 16: 9
full screen display.
Tint
Adjust color tones
1. Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Arrow (c,e,d,f)
Use to select the menu or to
make various adjustments.
Enter
Enter the setting of items in the
menu.
Picture
Access the Picture Setting menu
Info
Access the projector information
Exit
Exit and save the setting(s) of
items in the menu.
Menu
Turns on/off the on-screen display
menu.
Video
Composite video signal input
S-Video
S-Video signal input
Comp
Component Y/CB/CR input
PBP (Picture by Picture)
Enable the PIP function.
Comp HD
ACTIVE
DTV Y/PB/PR signal input
Switch to the active window in PIP
display mode.
RGB HD
DTV RGBHV signal input
PIP (Picture in Picture)
Enable the PIP function. Use
ARROW keys to adjust the
position of the PIP window (see
DVI
Digital/ Analog signal input
PIP+
Enlarge the size of PIP window.
PIP-
Shrink the size of PIP window.
8
1. Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
2. Installation
Remote Control
Push forward on the tap and lift to open the cover.
Install the two AAA batteries with the correct
polarity, then close the cover.
Notes on Batteries
■ Make sure that the battery polarities are correct when installing the batteries.
■ Do not mix an old battery with a new one or different types of batteries.
■ If you will not use the remote control for a long time, remove the batteries to avoid damage from battery
leakage.
Notes on Remote Control Operation
■ Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver
on the projector.
■ The useable range is between 3m/ 9.8 feet (from the front of the projector) and 4m/ 13.1 feet (from the top of
the projector) within a 30 degree horizontal angle and 15 degree vertical angle.
Projector
■ Connect the Power Cord
Plug the supplied power cord into the AC inlet in the
rear of this unit. (AC 100V ~ 240V)
Turn on the main power switch on the rear of this unit
(next to the AC inlet). The POWER LED will light up
in orange. Press ON key on the remote control for
ONE second to turn on the unit.
2. Installation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
■ Adjust the Lens Zoom/Focus ring
Adjust the projected image size you need with the
zoom ring on the lens. To focus the image, rotate the
focus ring on the lens.
Focus
Zoom in
Zoom out
■ Adjust the height
There are 4 screw adjusters on the bottom of this
unit. You can adjust the height or projection angle of
this unit by using these adjusters.
10
2. Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Installation For CL-510 (With 1.75 - 2.00 Lens)
Ceiling
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
CL-510 16 x 9 Screens:
Minimum: (screen width x 1.75) = __________ inches
Maximum: (screen width x 2.00) = __________ inches
C) VERTICAL OFFSET:
Screen width x 0.12 = _________ inches from the center of the lens.
Floor
2. Installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Throw Distance Chart For CL-510 (With 1.75 - 2.00 Lens)
CL-510 @ 1024 x 576
Min Throw
Distance
Max Throw
Distance
Vertical Offset
Position
Screen Height
Screen Width
40.5
43
72
77
126.00
134.75
140.00
146.41
152.25
155.75
161.00
162.75
168.00
175.00
180.25
182.00
187.25
190.75
196.00
203.00
210.00
224.00
248.50
255.50
280.00
144.00
154.00
160.00
167.32
174.00
178.00
184.00
186.00
192.00
200.00
206.00
208.00
214.00
218.00
224.00
232.00
240.00
256.00
284.00
292.00
320.00
8.64
9.24
45
80
9.60
47
84
10.04
10.44
10.68
11.04
11.16
11.52
12.00
12.36
12.48
12.84
13.08
13.44
13.92
14.40
15.36
17.04
17.52
19.20
49
87
50
89
51.5
52
92
93
54
96
56
100
103
104
107
109
112
116
120
128
142
146
160
58
58.5
60
61
63
65
67.5
72
80
82
90
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx1.75)
(SWx2.00)
Screen Width x 0.12
12
2. Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Installation For CL-510LT (With 2.30 - 3.00 Lens)
Ceiling
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
CL-510LT 16 x 9 Screens:
Minimum: (screen width x 2.30) = __________ inches
Maximum: (screen width x 3.00) = __________ inches
C) VERTICAL OFFSET:
Screen width x 0.10 = _________ inches from the center of the lens.
Floor
2. Installation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Throw Distance Chart For CL-510LT (With 2.30 - 3.00 Lens)
CL-510LT @ 1280 x 720
Min Throw
Distance
Max Throw
Distance
Vertical Offset
Position
Screen Height
Screen Width
40.5
43
72
77
165.60
177.10
184.00
192.24
200.10
204.70
211.60
213.90
220.80
230.00
236.90
239.20
246.10
250.70
257.60
266.80
276.00
294.40
326.60
335.80
368.00
216.00
231.00
240.00
250.98
261.00
267.00
276.00
279.00
288.00
300.00
309.00
312.00
321.00
327.00
336.00
348.00
360.00
384.00
426.00
438.00
480.00
7.20
7.70
45
80
8.00
47
84
8.37
49
87
8.70
50
89
8.90
51.5
52
92
9.20
93
9.30
54
96
9.60
56
100
103
104
107
109
112
116
120
128
142
146
160
10.00
10.30
10.40
10.70
10.90
11.20
11.60
12.00
12.80
14.20
14.60
16.00
58
58.5
60
61
63
65
67.5
72
80
82
90
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx2.30)
(SWx3.00)
SWx0.10
14
2. Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
3. Connecting
When connecting, make sure to:
1. Turn off all equipment before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly connected.
4. Connect all audio signals to external speakers. This projector is not equipped with speakers.
Connecting Video Inputs
■ Video / S-Video / Component (Interlaced Video)
DVD Player
3. Connecting
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
■ Progressive Component (DTV Y/PB/PR)
DTV Source
■ RGBHV (DTV RGB)
DTV Source
The RGB BNC input supports two kinds of HDTV formats: Progressive component (DTV Y/PB/PR) and DTV RGB. The
unit will detect the resolution automatically.
16
3. Connecting
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
4. Basic Operation
Turning on the Power
■ The Power LED lights orange when power is applied
and the power switch is turned on.
■ Press and hold the ON key on the remote control
for ONE second to turn on the unit. The POWER
LED will blink orange during warm up period, then
light solid green.
■ " Searching…." will be displayed on the screen before
the projector identifies the input signal. This message
will remain on the screen until a valid signal is
detected.
■ If an incompatible input signal exceeds the range of
the projector a "Not supportive timing" message will
be displayed on the screen. This message will remain
on the screen until you change the input signal.
Zoom/ Focusing
■ Adjust the projection image size you need with the
zoom ring on the lens. To focus the image, rotate the
focus ring on the lens.
Focus
Zoom in
Zoom out
Selecting Video Memory
■ Press M1, M2, M3 buttons to recall settings in the
memory.
■ Press Default to select the default setting.
18
4. Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Selecting "ASPECT RATIO"
■ Select the proper aspect ratio according to the
content being used. There are four aspect ratios:
■ Anamorphic: 4:3 image is stretched horizontally
to fit a 16: 9 screen. This is for 16:9 DVDs.
■ 4 X 3: The input signal will be scaled to fit 4 : 3
display mode in the center screen.
■ Letterbox: Image in letterbox format is enlarged
to fit 16:9 full screen display and the upper/lower
portion are cropped.
■ VirtualWide: This transforms a 4x3 image to a
16x9 image.
■ LPos+, LPos-: Adjust Letterbox image vertical
position.
Direct Picture Adjust (Menu Bypass)
■ Press Color to adjust color intensity.
■ Press Brightness to adjust picture brightness.
■ Press Contrast to adjust picture contrast.
■ Press Tint to adjust color tones.
Setting Menu
■ Press the Menu button to turn on /off the on-screen
menu.
■ Use the ARROW buttons (c,e,d,f) to select the
menu or to make various adjustments.
■ Press the Enter or f button to enter the setting of
items in the menu, or press the Exit button to leave
and save the setting of items in the menu.
■ For more detailed settings, see Chapter 5 Menu on
■ Press Picture to access the picture setting menu.
■ Press Info to access projector information.
4. Basic Operation
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Selecting Input Source
■ When this unit is turned on, it will search for the
input source you last selected.
■ You may select the input source directly on the
remote control.
PIP/ PBP function
■ Press the PIP button to enable the PIP function
■ For PIP purposes, there are two groups of inputs
separated by their display modes:
Video Group: Video, S-Video and Component Y/CB/
CR inputs
Graphic Group: HDTV input and Computer input.
■ The PIP can show one input from the Graphic Group
within one input from the Video Group, or show one
input from Video Group within one input from the
Graphic Group.
■ Press the PIP button to switch to the main window
or turn off PIP function.
■ Select the input source of the main window by
pressing the INPUT button.
■ Press the ACTIVE button to switch to the active
window. You can change the input signal setting in
the active window.
■ Press PIP+ or PIP- to adjust the size of PIP window.
■ Adjust the position of the PIP window with the
ARROW keys (c,e,d,f).
■ Press PBP to enable the PBP function.
20
4. Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Turning off the Power
■ Press the OFF key on the remote control to turn
off the unit.
■ The POWER LED will blink green and the fans will
speed up for a quick cool down. The projector
will not respond to any command for 90 seconds.
■ The POWER LED will light solid orange once the
cooling down cycle has completed.
■ Fans will run for three minutes to cool.
■ You may turn the projector back on after the first
90 seconds.
4. Basic Operation
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
5. Menu
Using the Menu
This unit is equipped with an on-screen display (OSD) menu for making various adjustments and settings.
■ Press the Menu button to turn on /off the on-screen display menu.
■ Use the ARROW buttons (c,e,d,f) to select the menu or to make various adjustments.
■ Press the Enter or f button to enter the setting of items in the menu, or press the Exit button to leave and save
the setting of items in the menu.
Main Menu
Runco CL-510
> Video
S-Video
Component
Source selection and picture quality adjustments
Component HD
RGB HD
DVI-I
-----------------------
Aspect Ratio
Options
Setup
Aspect ratio selection
Option selection
Setup selection
When the Menu button is pressed on the remote control, the main menu will appear on-screen. An example of the
main menu is shown above. Use c or d button to move the item you want to choose and then press the Enter or f
button.
The active source is indicated by an arrow ( > ) to the left of the source; note that in the example above, Video is the
current source.
22
5. Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Picture Quality Adjustments
Runco CL-510
> Video
Adjustment
Brightness
S-Video
Contrast
Color
Tint
Sharpness
Filter
Component
Component HD
RGB HD
DVI-I
-----------------------
Aspect Ratio
Temperature
Store
Options
Set Up
Recall
To access the picture quality adjustments, press Menu, highlight the active source (indicated by the arrow) and press
Enter or f. The picture quality sub-menu will then appear (see above).
To make an adjustment to a particular function, highlight the function with the c or d arrow button and press Enter
or fto activate a scroll bar for that adjustment.
To enter into the memory selection menus, use Store and Recall menus to save and load up to three different
memories. There are three memories: Memory 1, Memory 2 and Memory 3.
Aspect Ratio
Runco CL-510
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
-----------------------
Aspect Ratio
Options
Set Up
Adjustment
> Anamorphic (16:9)
Standard (4:3)
Letterbox
Virtual Wide
There are four aspect ratios available that can be selected for video signal inputs.
16:9 Screens:
■ ANAMORPHIC: The image is compressed vertically, but anamorphic software will appear properly
proportioned. This is best suited for use with 16:9 DVD's.
Active Image Area
5. Menu
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
■ 4 x 3: The input signal will be scaled to fit in the center of the 16:9 screen.
Active
Image Area
■ LETTERBOX: The image in the Letterbox mode will be stretched vertically, and the top and bottom portion
'blanked off'. This ratio is best suited for LaserDisc movies or non-anamorphic DVD's.
Active Image Area
■ VIRTUAL WIDE: A 4:3 image is transformed into a 16x9 image.
Options
Runco CL-510
> Video
S-Video
Component
Component HD
RGB HD
Options
> Reset Adjustments
Language
Picture Orientation
DVI-I
Logo Light
-----------------------
Sleep Timer
Aspect Ratio
Lamp Hours
Options
Set Up
OSD Position
PC & HD Adj.
Press Enter on selected feature to open the adjustment menu.
Reset Adjustments: Use this function to reset all values of the current source back to factory default.
Language: There are 4 different menu languages available: English, Spanish, French and German.
Picture Orientation: The projector can be installed on a ceiling or in a rear screen configuration with one or more
mirrors. There are four settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.
Logo Light: To turn on or off projector logo light.
Sleep Timer: To setup auto off timer. The setting timer is from 10 minutes to 3 hours.
24
5. Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Lamp Hours: To check for total time of lamp usage.
OSD Position: To adjust horizontal and vertical positions of OSD.
PC & HD Adj.: The following settings are only available with a PC or DTV RGB signal. There is no position adjustment
when using DVI-D signal.
■ AUTO: Adjusts the phase, frequency and position automatically.
■ FREQ.: Adjusts the frequency of the signal.
■ PHASE: Adjusts the phase of the input signal.
■ H. POS.: Adjusts the horizontal position of the image.
■ V. POS.: Adjusts the vertical position of the image.
Setup
Runco CL-510
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
-----------------------
Setup
> Keystone
Blue Image
White Balance
Aspect Ratio
Options
Reset Lamp Timer
Setup
Background Color
The Setup menu is passcode protected and for use by Runco personnel only. Many of the adjustments available in this
section are intended for use by trained service personnel only. If you are having difficulty with one of these items, please
contact your Runco Dealer for service.
All items below which are printed in italic are intended for service personnel only. Non-italic items can be modified by
the projector owner.
The CL-510 has four memory settings for color temperature. Three of these settings are factory set to default as
follows:
Te m p 1 -- 5400 kelvin
Te m p 2 -- 6500 kelvin
Te m p 3 -- 7500 kelvin
The Temp 4 memory is installer adjustable and can be used to create custom settings. A passcode must be entered in
order to change this setting. There are nine adjustable "white balance" parameters available for the Temp 4 setting.
Once the desired adjustments have been entered, selecting "store" will save these custom settings into the "Temp 4"
memory position.
Keystone: Corrects the trapezoidal distortion as a result of the angle of projection (-12° ~ +12°). This can correct for up to +/-
12 degrees of offset.
Blue Image: This mutes the red and green.
5. Menu
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
White Balance: To adjust grey scale.
White Balance
Red Gamma
Adjust the Gamma Curve
Green Gamma
Blue Gamma
Red Gain
Adjust High End
Adjust Low End
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Store
Reset Lamp Timer: Use this function to reset lamp usage counter. Reset only if you replace the lamp.
Background Color: To adjust background color to blue or white.
26
5. Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
6. Additional Information
Warning Message
■ It is normal for lamp to be darker when this unit
has been used for a period of time.
■ " Lamp life is expired ! Please install new lamp. And
reset the lamp timer" message will be displayed for
30 seconds on the screen if the lamp has operated
for 950 hours.
Lamp life is expired !
Please install new lamp
And reset the lamp timer
■ " Please change the lamp, Lamp will exceed its
lifetime after (hours):" message will be displayed
on the screen for 30 seconds for each time turning
on, if the lamp has operated for 980 hours. And
the number will count down continuously.
Please change the lamp !
Lamp will exceed its
lifetime after (hours):
■ "Please change the lamp !" message will display on
the screen all the time and the POWER LED will
blink in orange and green sequentially if the lamp
has operated for more than (1,000) hours.
■ The power will turn off automatically after 10
minutes.
Please change the lamp !
Replace the Lamp (Contact your Runco Dealer)
1. Loosen the screw of
front lamp cover
2. Take off the front lamp
cover.
2
1
3. Loosen the two
screws of lamp
module.
4. Pull out the lamp
module horizontally.
5. Insert the new lamp
module into this
projector
6. Tighten the two screws
of lamp module.
horizontally until it
is securely in place.
6. Additional Information
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
7. Put on the front
lamp cover.
8. Tighten the screw of
front lamp cover.
9. Turn on the power and
go into the Set Up menu
to reset the "Lamp
Timer" item.
Troubleshooting
Problem
Possible Cause
Remedy
This unit does not
turn on.
There is no power from power cable.
Plug the power cord into the AC inlet on the
rear of this unit, and plug the power cord into
to the power inlet.
The power switch is not turned on.
Turn on the power switch.
Turn on this unit again within the
cooling down procedure.
Wait until this unit completes the cooling down
procedure.
Front lamp cover is not attached well.
Correctly attach the front lamp cover.
Correctly attach the front lamp cover.
No picture
The front lamp cover is not correctly
attached.
This unit is not correctly connected to Check the connection.
the input source device.
The input signal has not been correctly Select the correct input signal with the input
selected.
keys: Video, S-Video, Component, Component
HD, RGB HD and DVI-I on the remote control.
POWER LED or LAMP LED blinking.
Please contact your Runco dealer for
assistance.
Image is unstable
Picture is blurred
The connection cables are not
connected to this unit.
Correctly connect the cables to the
appropriate terminals.
The projection lens is not correctly
focused.
Adjust the focus of projection lens with the
focus ring.
This unit and the screen are not
aligned squarely.
Adjust the projection angle and direction, and
the height of this unit.
Remote control does
not work correctly
The batteries are exhausted.
Replace both batteries with new ones.
LAMP LED blinks in
red
The front lamp cover is not correctly
attached.
Correctly attach the front lamp cover.
The cooling fan does not work well.
Please contact your Runco dealer for
assistance.
The temperature inside this unit is
extremely high.
Check that the ventilation holes are not
blocked.
POWER LED blinks in The lamp has exceed its specified
Replace the lamp with a new one.
orange and green
sequentially
usage hours.
The lamp has burned out.
Replace the lamp with a new one.
28
6. Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
Specifications
CL-510/ CL-510LT Specifications
Projector Type:
Digital Light Processing™ (DLP™), Single Matterhorn DMD™ Chip
Native Resolution:
Aspect Ratios:
1024 x 576, (16:9)
4:3, Letterbox, 16:9, Anamorphic, Virtual Wide
NTSC, PAL
Video Standards:
DTV Compatibility:
Scan Frequency:
480p, 720p, 1080i
Horizontal: 15-80 kHz
Vertical: 50-100 Hz
Picture Size (16:9 Screen):
Recommended Width: 72-96 in.
Maximum Width: 200 in.
Throw Distance
(Factor x Screen Width):
CL-510: 1.75 to 2.00/ CL-510LT: 2.30 to 3.00
Light Output:
900 ANSI Lumens*
CSMS** Specifications:
Home Theater Calibration:
471 ANSI Lumens
17.8 Foot-Lamberts (fL)
Contrast Ratio:
Lamp:
1700:1
CSMS** Contrast Ratio: 149:1
210W
o
Lamp Life:
Inputs:
1000 hours @ 6500 Kelvin
(1) Composite Video, (1) S-Video,
(1) RGB/Component (via BNC),
(1) RCA Component Video,
(1) DVI w/ HDCP, (1) RS-232
Memories:
21 memories
12V Output:
Max .250 Amp, active when the projector is on
100-240V AC, 50/60 Hz, 310 watts
Power Requirements:
Operating Environment:
Dimensions (w/out feet):
41°- 95° F, (5°- 35° C), 20%-80% Humidity (non-condensing)
Width: 16.15 in. (410.16 mm),
Depth: 14.56 in. (369.71 mm),
Height: Without feet 5.3 in. (134.62mm)
with feet 5.8 in. (148.62 mm)
Weight: 22 lbs. (10 kg) (includes lens)
Regulatory Approvals:
Limited Warranty:
UL, CSA, GS-TUV, CCIB, CB,
FCC, CE, VCCI and C-Tick
Projector: (2) Two year parts and
labor from the date of
delivery to the end user
Lamp Warranty: 6 months
6. Additional Information
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
*ANSI Lumen specification:
This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is
included in RUNCO literature to allow for direct comparison with other manufacturer's projectors. These
measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is
used in professional, commercial, and industrial displays.
**CSMS Home Theater Calibration ANSI Lumen Specification:
These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated
to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.
**CSMS Home Theater Calibration foot-Lambert (fL) Specification:
This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion
Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using
an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters using DLP™ technology. The foot-Lambert is dependant on screen size, screen
gain, and projector light output.
All measurements are made at RUNCO to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650
SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech
o
130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500 Kelvin and has a
minimum of 150 hours of usage.
30
6. Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco CL-510/ CL-510LT User’s Manual
PC Out Adapter
RS-232 Setup
1. Connect D-Sub 9-pin female to RJ-11 adapter (not
included) to Com port on PC.
Baud Rate: 115200 or 9600
Parity: None
2. Connect RJ-11 to Projector.
Data Bits: 8 Bits
RJ-11 to D-Sub 9-pin (not included)
Stop Bits: 1 Bit
Flow Control: None
RS-232C Control Codes
Code
X01
X02
X03
X04
X10
X11
X12
X13
X14
X15
X16
X20
X21
X22
X23
X24
X25
X35
X36
X37
X38
X40
X41
X42
X46
X47
X48
X49
X55
X56
X57
X60
X61
X62
X85
X90
X91
X92
X93
X94
X95
Function
Power On
Power Off
Message On
Message Off
Menu (arrow key)
Enter (arrow key)
Exit (arrow key)
RS-232 For D-Sub 9-pin (not included)
5
4
3
1
2
6
9
8
7
D-Sub 9-pin female
Details
TxT
2
D-Sub 9-pin female
3
RxD
Up (arrow key)
Down (arrow key)
Left (arrow key)
5
Ground
NC
1, 4, 6, 7, 8, 9
Right (arrow key)
Switch to Composite input
Switch to S-Video input
Switch to Component input
Switch to D-Sub _PC input
Switch to YPBPR input
Switch to BNC_PC input
Anamorphic
Standard
Letter box
Virtual Wide
Load memory 1 settings
Load memory 2 settings
Load memory 3 settings
Load default of current source
Save memory 1 settings
Save memory 2 settings
Save memory 3 settings
Switch active source
Picture in picture display
Picture in picture display
Switch language - English
Switch language - French
Switch language - Spanish
PC Input - auto
Warning: During initial turn on and turn off of the
projector, this unit will not accept RS-232 codes for 20
seconds.
RS-232 For RJ-11 (not included)
4-pin RJ-11
Details
TxT
2
3
RxD
1, 4
Ground
Yellow
Green
Green
Yellow
1
2
Black
Red
Black
Red
3
4
NOTE:
Image orientation - floor front
Image orientation - ceiling front
Image orientation - floor rear
Image orientation - ceiling rear
Back light on
1. All codes are in the ASCII format.
2. A carriage return is required after each command.
Back light off
32
6. Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
|