16. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
OWNER'S MANUAL
All warranty claims must be filed through the authorized Royal Sovereign dealer or
reseller through which the equipment was originally purchased. Model, serial number
and date of delivery are required for all claims.
RSC-1400L Laminators
The warranty made herein is in lieu of all other warranties, expressed or implied,
including any warranty or merchantability or fitness for a particular purpose. Royal
Sovereign will not be liable for personal damage or personal injury (unless primarily
caused by its negligence), loss of profit, or other incidental or consequential damages
arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting or improper use of the machine. Warranty repair or
replacement by Royal Sovereign or its authorized Reseller(s) does not extend the
warranty beyond the initial one year period from the date of installation. Unauthorized
customer alterations will void this warranty.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1) 800-397-1025
FAX : +1) 201-750-1022
E-mail : [email protected]
Royal Sovereign Inc. <Oversea Sales Office>
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830
E-mail : [email protected]
RS Holland B.V.
Planetenweg 75 2132HM Hoofddorp, The Netherlands.
TEL : +31) 23-5626620, +31) 23-5654451
FAX : +31) 23-5654565
Read all instructions carefully before use.
For any Customer Support needs please choose the
E-mail : [email protected]
RS International Australia PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : +61) 2-9674-2127
FAX : +61) 2-9674-2027
E-mail : [email protected]
RS Canada Inc.
164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
Royal Sovereign International Inc.
TEL : +1
)
416-741-8400 FAX : +1 416-741-8185
)
E-mail : [email protected]
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
3. INSTALLATION
Note: The laminator should be installed by a trained service technician.
4. INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
The laminator comes fully assembled, except for the feed table, paper guide. Upon arrival,
thoroughly inspect the unit. It is imperative that any shipping damage is reported and a
claim is filed with the delivering carrier immediately upon receipt.
Quantity
1
Picture
Part Name
Laminator
The laminator should be located in an area with adequate work space for feeding graphics
and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Owner's Manual
1
Once the laminator is in place, lock the casters into position(“ON” position). Always unlock
the casters (“OFF” position) when moving to a different location.
3´´(76mm) / 2" (57mm) Auto Grip
6/4
L-wrench (2.5)
Dust Cover
1
ELECTRICAL REQUIREMENTS
1
1
1
Royal Sovereign recommends that a licensed electrician ensuresproper power installation
to your laminator in accordance with electrical codes in your area.
Spare Motor Fuse - FUSE(50T)
(6.3A)
The laminator should have a dedicated power line.
Spare Main Power Fuse - FUSE(65TS)
(5A)
MODEL
RSC-1400L
single phase
8 - 1/4"Hexa head Bolt (M6 20mm)
8 - Spring Washer( 6.1)
220-240V
50/60HZ
120V
50/60HZ
10/10
12/12
Power Supply
(Included with option only)
12 - 3/16"screw (M5 10mm).
12 - Spring Washer( 5.1)
(Included with option only)
Front Feeder and Rear Rewinder Kit
(Included with option only)
2/2
4
4 - 1/3"Hexa head Bolt (M8 70mm)
4 - Spring Washer( 8.5)
120V UL
230V UL
240V UK
(Included with option only)
4 - 1/3"screw (M8 60mm).
4 - Spring Washer( 8.5)
(Included with option only)
4
4
NUT M8)
220V EU
220V AU
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC -1400L
5. PRODUCT IDENTIFICATION
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed.
12
2
1
3
4
11
10
9
5
6
8
13
7
RSC-1400L
NO.
1
PART NAME
RSC-1400L
SAFETY COVER
O
O
O
O
O
O
O
O
O
O
O
O
O
Control Buttons
2
EMERGENCY SWITCH
FRAME-PAPER GUIDE
TABLE-FRONT
3
1. SPEED DISPLAY: Display’s current Speed.
4
2. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers,
5
MAIN ROLLER
press the up or down arrow button.
6
ASSEMBLY STAND
FOOT PEDAL
3. RUN: To start the rollers.
7
4. STOP: To stop the rollers.
8
TENSION CONTROL KNOBS
PRESSURE LEVER
CONTROL PANEL
UPPER IDLE BAR
RELEASE LINER TAKE UP
REMOTE CONTROL
5. REV: To reverse the rollers, press and hold the REVERSE button.
9
10
11
12
13
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
7. ROLLER NIP SETTING
8. USING FOOT PEDAL AND REMOTE CONTROL
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
USING FOOT PEDAL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
“Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat
to stop the rollers.
Metric
NO.
Inches
(mm)
Lamination
1
1
2
3
4
5
Lamination
1/ 25"
3/16"~1/4"
3/ 8"~1/2"
3/5"
5-7
10-13
15
NOTE: If you don't want to
laminate,please place the
pressure lever to the "Open
position(NO.5)".
USING REMOTE CONTROL
1
2
3
Located on the rear left side of the laminator.
1. PRESS RUN – To activate the rollers.
2. PRESS STOP – To stop the rollers from turning.
3. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
9. USING CROSS CUTTER
10. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll
The cross cutter is located in the rear exit table of the machine.
(adhesive in).
Loading films to upper and lower film shafts:
(See page 5 for assistance with parts identification.)
1. After lamination, move the cutter approximately to
the center of the completed application at the
desired point of detachment (Figure 1).
1. Adjust the auto grip to fit to the film and tighten the
auto grip screw (Figure 1).
Figures 1
Figures 2
Figures 3
Figure 1
2. Remove the upper and lower film shafts from the
machine and load the films (Center the upper and
lower films on the shaft). Note the direction of the
adhesives on the lower and upper films
(Figure 2).
2. Grasp film with one hand, press the cutter
downward into the application and slide it first to
one end of the application, then to the other end to
complete the cut (Figure 2 & 3).
Figure 2
3. Load the upper and lower film shafts on the
machine (Figure 3).
Figure 3
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
11. THREADING FILM
8. Cut and separate the release liner and the film.(Figure
3)
Figure 3
9. Thread the craft paper behind the Lower Idle Bar to
the top film that is resting on the main roller (do not
use the Lower Idle Bar for Mounting). (Figure 4)
11.1. Decaling
10. Reinstall the Feed Table and the Frame-Paper
Guide,and close the Safety Cover.
Figure 4
Figure 5
Figure 6
1. Turn the power switch on (“I” position). The Power
switch is located on the rear left side of the unit.
11. Adjust the nip setting to appropriate gap.
2. Complete the steps as in the “LOADING FILM”
section (see page 10).
12. Insert and push the leader board until they reach the
front nip point.
3. Take off the Frame-Paper Guide and the Feed Table.
13. Push the Run button.
4. Pull the top film down over the Safety Cover to the
bottom of the craft paper / Mounting film.
14. Push the leader board into the rollers. (Figure 5)
Figure 1
5. Align and center the craft paper / Mounting film to the
top film and tighten the two lower core screws (Figure
1).
15. Adjust the top and bottom tension knob by rotating it
clockwise or counterclockwise. Turn it until the top
and bottom roll films have some resistance varies
(the tension depending on the film thickness; the
thicker the film the more tension is required).
(Figure 6)
6. Thread the top film underneath the Upper Idle
Bar.(Figure 2)
7. Tape the top film on to the Release Liner Take-
Up.(Figure 2)
Figure 2
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
16. Press the Stop button when the leader board has completely exited from the rollers.
17. Use the Cross Cutter to cut the leader board from the web (see page 9).
4. Flip the image over the top roller and hold on to the
release liner (Figure 4).
18. Set the nip setting to the appropriate position for the Over-lamination / Decaling
application.
Figure 4
11.2. Mounting
1. Lay the decaled image face down on a flat surface.
Carefully peel back and put a crease along the
edge of the release liner ( Approximately 1 in or
25mm, Figure 1).
5. Press the foot pedal once, and then let it go while
slowly pulling the release liner as the board enters
the main roller nip (Figure 5)
Figure 5
6. Press the foot pedal once again when the board has
completely exited from the rear of the unit. Trim the
board if necessary.
Figure 1
2. With the image facing up, align the image onto the
board. Press firmly from the center out (Figure 2).
Figure 2
3. Adjust the pressure lever to ensure the proper
opening (Figure 3).
Figure 3
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC-1400L
12. INSTALLATION OF FRONT FEEDER and REAR
REWINDER OPTIONS
4. Disassemble the power switch bracket and place the left
rewinder outside of the frame; fasten with round head
3/16"(M5) screws (included in the option kit). Then,
reinstall the power switch bracket (Figure 7).
Note: Below options are to be installed by an authorized RS reseller.
Installation of the Front Feeder Option (Includes 2 brackets,
one spindle, and mounting hardware).
Figure 7
Figure 8
Figure 9
5. Install the right rewinder on the outside of the frame and
connect the motor wire connector to the rear wire
(Figures 8 & 9).
1. Install the Front Feeder to the inside of the front frames
using four 1/4"(M6) hexagon bolts on each side (Figure 1)
Figure 1
Installing the Rear Rewinder Option (Includes motorized
winder, bracket, one spindle, and mounting hardware).
6. Reinstall the rear cover.
1. Remove the left and right covers by using a Phillips
screwdriver (four screws on each side cover) (Figures 2 &
7. Reinstall the side covers.
Figure 2
Figure 3
3).
8. Reinstall the lever knob and screw.
2. Remove the lever knob screw and lever (Figure 4).
Figure 4
3. Remove the rear cover by removing all
10 screws (4 top, 4 bottom, and 1 on
each side) (Figure 5 & 6).
Figure 5
Figure 6
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
RSC -1400L
13. MAINTENANCE
15. SPECIFICATIONS
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
Description
Power supply
RSC-1400L
AC 100, 200, 220~240V 50/60Hz 120V 60Hz
1. Remove the film from the laminator.
Power consumption
Max laminating width
Film thickness
100W
1400mm / 55"
60~500 mic / 1~15mil
5m/min / 16.4ft/min
Not applicable
None
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Max laminating speed
Ready time
Heating method
Lubrication
Driving motor
DC geared
Max Temperature contro
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
l
Not applicable
Speed control
Transport type
Film core size
Cross cutter
9 settings
2 Roller
Auto grip (2",3")
Yes
Hot lamination
Cold lamination
Mounting thickness
Take up system
Reverse
No
14. TROUBLESHOOTING
Yes
Symptom
Cause
Possible Solution
15mm / 0.6"
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
Chain link to main motor
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
Machine will not turn
on:
Yes
Yes
Yes
Remote control
Foot pedal
d. Blown main power fuse.
c. Reset the circuit breaker.
d. Replace the fuse.
Unit dimensions
(w x d x h)
1710 650 1210 (mm)
67.5" 21.5" 47.5"
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
the micro switch is activated.
Unit weight
210kg / 462.9bs
d. Replace the motor fuse.
c. Blown motor fuse.
Carton dimensions
(w x d x h)
1960
900 850(mm)
77" 35.5" 33.5"
The unit is not heating
up:
a. Did not raise the temperature.
a. Raise the temperature.
Gross Weight
292kg / 643.7lbs
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
Curled lamination:
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|