Owner’s Manual
RSP-1098
Surround Sound Processor
SURROUND SOUND PROCESSOR RSP-1098
STANDBY
ZONE
2
FUNCTION
VOLUME
PUSH
PATH
SPEAKER
MODE
DISPLAY
MENU
MUTE
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
Important Safety Instructions
WARNING: There are no user serviceable parts inside. Refer
all servicing to qualified service personnel.
The COMPUTER I/Oconnectionshould be handled by authorized person
only.
WARNING: To reduce the risk of fire or electric shock, do not
expose the unit to moisture or water. Do not allow foreign
objects to get into the enclosure. If the unit is exposed to moisture,
or a foreign object gets into the enclosure, immediately dis-
connect the power cord from the wall. Take the unit to a qualified
service person for inspection and necessary repairs.
FCC Information
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used in accordance
with the instruction, may cause harmful interference to radio communica-
tions.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on the
product itself. Follow all operating instructions.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Clean the enclosure only with a dry cloth or a vacuum cleaner.
You must allow 10 cm or 4 inches of unobstructed clearance around the
unit. Do not place the unit on a bed, sofa, rug, or similar surface that could
block the ventilation openings. If the unit is placed in a bookcase or cabi-
net, there must be ventilation of the cabinet to allow proper cooling.
•
•
•
Reorient or relocate the receiving antenna.(TV, radio, etc.)
Increase the separation between the equipment and receiver
Keep the component away from radiators, heat registers, stoves, or any
other appliance that produces heat.
Connect the equipment to an outlet on circuit different from that to which
the receiver is connected.
The unit must be connected to a power supply only of the type and voltage
specified on the rear panel. (USA: 115 V/60Hz, EC: 230V/50Hz)
•
Consult the dealer or an experienced radio/TV technician for additional
help.
Connect the component to the power outlet only with the supplied power
supply cable or an exact equivalent. Do not modify the supplied cable. Do
not defeat grounding and/or polarization provisions. The cable should be
connected to a 2-pin polarized wall outlet, matching the wide blade of the
plug to the wide slot of the receptacle. Do not use extension cords.
Caution
This device complies with part 15 of the FCC Rules operation is subject to
the following to conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Do not route the power cord where it will be crushed, pinched, bent, ex-
posed to heat, or damaged in any way. Pay particular attention to the power
cord at the plug and where it exits the back of the unit.
The power cord should be unplugged from the wall outlet if the unit is to be
left unused for a long period of time.
Immediately stop using the component and have it inspected and/or ser-
viced by a qualified service agency if:
• The power supply cord or plug has been damaged.
• Objects have fallen or liquid has been spilled into the unit.
• The unit has been exposed to rain.
• The unit shows signs of improper operation
• The unit has been dropped or damaged in any way
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
4
1: Front and Rear Panels
1
2
3
4
SURROUND SOUND PROCESSOR RSP-1098
STANDBY
ZONE
2
FUNCTION
VOLUME
PUSH
PATH
SPEAKER
MODE
DISPLAY
MENU
MUTE
5
6
7
8
9
10 11
12
13
14 15
16 17
18 19
20 21 22
23 24
25
26
3
1
ZONE2
2
S-VIDEO
POWER
ON
COMPOSITE
40
OFF
SURROUND SOUND PROCESSOR
MODEL NO: RSP-1098
POWER CONSUMPTION: 70 WATTS
27 28
29
30
31 32
33
34
35
36
37
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5
2: RR-1050 Remote
CLONE REPT TRANSMITTER LOADING RECEIVER
EDIT LEARN
WAITING
CLONE REPT TRANSMITTER LOADING RECEIVER
AUD
V1
CD
TUN
TAPE
EXT
DEVICE / INPUT
A
V2
V3
3
V4
V5
POWER
EDIT LEARN
WAITING
ON
OFF
1
4
2
5
8
0
G
H
I
6
CH
VOL
7
9
MACRO
M
MUTE
MENU
+10
X
GUIDE
FRQ DIRECT
C
M
J
UP
ENT
DWN
CTR
OSD
B
TUNE
PRESET
K
+
-
L
C
FM MONO BAND
SEARCH –
SEARCH +
S
R
SUB
SUR
CD
DISC 1
D
E
F
M
N
DISC 2
DYN
DISC 3
REC
DISC 4
ZONE
DISC 5
SUR+
EQ
2CH
PL C
PL M
5CH
7CH
O
P
PROG
RANDOM REPEAT
DISC-
DISC+
DISPLAY
DISP
AUDIO
TAPE2
ANGLE
PHONO
SBTITLE
TONE
ZOOM
D-SLT
RESUME REPEAT
A -B
P-TUN
GOTO
TP
SLOW
TA
SCAN
PTY
INPUT 1
INPUT 2
INPUT 3
TV/VCR
RECORD
DVD
POWER
/ CLONE
EDIT
LEARN
CLEAR
LANG
PRELOAD RESET
PAGE 1/2
Q
R
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
6
3: On-Screen Display/TFT Screen Menus
SYSTEM STATUS
MAIN MENU
SPEAKER
LISTEN:Tuner
VID INPUT:Video 1
RECORD:Source
INPUT
DELAY
TEST TONE
ZONE 2
MODE:Dolby Digital
INPUT:Coaxial 2
VOLUME:65
SUB SETUP
DISPLAY
OTHER
CONTOUR
DEFAULT
ZONE 2:Off
SPEAKERS:FL CNT SUB FR
SL CB1 CB2 SR
EXIT
CONTOUR SETUP
INPUT SETUP
SPEAKER SETUP
LISTEN:CD
SPEAKER:Front
DEFEAT:On
VID INPUT:Video 1
INPUT LABEL:_______
INPUT:Coaxial 2
CINEMA EQ:Off
12V TRIGGER:1
DEFAULT MODE:Dolby 3 Stereo
GROUP DELAY:200ms
FRONT:Large
CENTER:Large
SURROUND:Large
CENTER BACK:Large1
SUBWOOFER:Yes
HF CONTOUR:+5
LF CONTOUR: 0
ADVANCED:Enter
MAIN MENU
MAIN MENU
MAIN MENU
DISPLAY OPTIONS
INPUT SETUP
ADV SPEAKER SETUP
LISTEN:Multi Input
VID INPUT:Video 1
INPUT LABEL:_______
DISPLAY SOURCE:Off
CONTRAST:+ 5
SPEAKER:Front
CROSSOVER:100Hz
BRIGHTNESS:- 5
DOLBY:Small
DTS:Small
STEREO/MPEG:Large
MUSIC:Small
PROGRESSIVE:No
OSD OUTPUT: SCREEN+MON
12V TRIGGER:1
LFE REDIRECT:On
MAIN MENU
MAIN MENU
SPEAKER SETUP MENU
SUBWOOFER SETUP
INPUT SETUP
LISTEN:CD
OTHER OPTIONS
CROSSOVER:100hZ
DOLBY DIGITAL: 0dB
DOLBY PL II: 0dB
DTS: 0dB
STEREO/MPEG:+ 2dB
MUSIC: Off
VID INPUT:Video 1
INPUT LABEL:_______
INPUT:Coaxial 2
CINEMA EQ:Off
RECORD:Source
TURN ON VOL:Last
MAX VOL:Max
VOL SPEED:Slow
POWER:Direct
LANGUAGE:English
VIDEO:NTSC
MAIN MENU
12V TRIGGER:1
DEFAULT MODE:Dolby PLII Cinema
GROUP DELAY:200mS
MAIN MENU
MULTI INPUT:- 2dB
OPTION
MAIN MENU
DOLBY PRO LOGIC II
MODE:Music
TEST TONE
LEFT:+ 1dB
CENTER:- 1dB
ZONE2SETUP
SOURCE:Off
VOLUME SETUP:Variable
VOLUME:60
TURN ON VOL:Last
MAXVOL:Max
12V TRIGGER:Off
RIGHT:+ 2dB
OPTIONAL PARAMETERS
PANORAMA:Off
DIMENSION:3
R SURROUND:+ 5dB
R CTR BACK:+ 2dB
L CTR BACK:+ 2dB
L SURROUND:+ 4dB
SUBWOOFER:+ 9dB
CENTER WIDTH:0
INPUT SETUP MENU
MAIN MENU
MAIN MENU
DTS Neo:6
DELAY SETUP
DEFAULT SETUP
LEFT: 12ft 3.6m
CENTER: 11ft 3.3m
RIGHT: 11ft 3.3m
MODE:Cinema
FACTORY DEFAULT:No
R SURROUND: 6ft 1.8m
R CTR BACK: 8ft 2.4m
L CTR BACK: 9ft 2.7m
L SURROUND: 5ft 1.5m
SUBWOOFER: 5ft 1.5m
USER DEFAULT:No
SET USER DEFAULT:No
INPUT SETUP MENU
MAIN MENU
MAIN MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7
4: Outputs
SUBWOOFER
AMPLIFIER
FRONT
SURROUND
R
L
CENTER
CENTER
BACK
RSP-1098
3
1
ZONE2
2
S-VIDEO
POWER
ON
COMPOSITE
OFF
SURROUND SOUND PROCESSOR
MODEL NO: RSP-1098
POWER CONSUMPTION: 70 WATTS
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
8
5: Source Connections
DVD
VIDEO
OUTPUTS
Y
L
COMPOSITE
S-VIDEO
CR
CB
COMPONENT
VIDEO
R
DIGITAL
OUTPUT
AUDIO
OUTPUT
RSP-1098
3
1
ZONE2
2
S-VIDEO
POWER
ON
COMPOSITE
OFF
SURROUND SOUND PROCESSOR
MODEL NO: RSP-1098
POWER CONSUMPTION: 70 WATTS
VCR
L
S-VIDEO
R
COMPOSITE
REC
IN
LINE
OUT
REC
IN
LINE
OUT
VIDEO
AUDIO
TAPE
L
R
LINE
OUT
REC
IN
CD
L
R
OPTICAL
DIGITAL OUTPUT
ANALOG
OUTPUT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
9
6: Zone 2 Connections
CD
ROTEL RSP-1098
3
1
ZONE2
2
S-VIDEO
POWER
ON
COMPOSITE
OFF
SURROUND SOUND PROCESSOR
MODEL NO: RSP-1098
POWER CONSUMPTION: 70 WATTS
AMPLIFIER
ZONE 2 IR
RIGHT
LEFT
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
10
Making Connections..............................17
CD Player ........................................................ 17
DVD Player ...................................................... 17
Cable, Satellite, or HDTV Tuner ......................... 17
AM/FM Tuner .................................................. 17
Audio Tape Recorder ........................................ 17
VCR or Digital Video Recorder .......................... 17
DVD-A or SACD Player ..................................... 17
TV Monitor ....................................................... 18
Amplifiers and Powered Subwoofers................. 18
CONNECTIONS
13
Contents
Boxed numbers refer to RSP-1098 illustration.
Boxed letters refer to RR-1050 illustration.
Analog Audio Inputs & Outputs ............13
CD Inputs
.................................................. 13
.............................................. 13
............................................... 13
............................................ 13
Tuner Inputs
TAPE Inputs
TAPE Outputs
Important Safety Instructions ............................. 3
1: Front and Rear Panels ................................... 4
2: RR-1050 Remote ........................................... 5
3: On-Screen Display/TFT Screen Menus ............. 6
4: Outputs ......................................................... 7
5: Source Connections ........................................ 8
6: Zone 2 Connections ....................................... 9
VIDEO 1–5 Audio Inputs
VIDEO 1–3 Audio Outputs
........................... 14
......................... 14
MULTI Inputs
............................................. 14
........................................ 14
Preamp Outputs
ZONE 2 Audio Outputs ............................... 14
OPERATING THE RSP-1098
18
About Rotel .........................................12
Video Inputs & Outputs ........................14
Getting Started ....................................12
Video features ................................................. 12
Audio features ................................................. 12
Surround features ............................................ 12
Other features ................................................. 12
Unpacking ....................................................... 13
Placement ....................................................... 13
Front Panel Overview ..........................18
VIDEO 1–5 Composite Video Inputs
VIDEO 1–3 Composite Video Outputs
........... 15
......... 15
Color TFT Display
MENU button
DISPLAY Button
STANDBY Button
VOLUME Knob
MUTE Button
...................................... 18
...................................... 18
......................................... 18
....................................... 18
........................................... 18
...................................... 19
........................................ 19
.............................................. 19
........................................ 19
............................................ 19
.......................................... 19
.............................................. 19
VIDEO 1–5 S-Video Inputs
VIDEO 1–3 S-Video Outputs
......................... 15
...................... 15
VIDEO 1–4 Component Video Inputs
......... 15
TV Monitor Outputs
...................... 15
ZONE 2 Video Outputs
............................... 15
FUNCTION Knob
PATH Button
Digital Audio Input & Outputs ...............15
Digital Inputs
..................................... 15
................................... 16
SPEAKER Button
MODE Button
Remote Sensor
ZONE 2 LED
Digital Outputs
Other Connections ................................16
AC Input ................................................... 16
Master Power Switch
................................. 16
......................... 16
12V TRIGGER Connections
REM IN Jacks
IR OUT Jacks
Computer I/O
............................................ 16
............................................. 16
........................................... 16
Download from Www.Somanuals.com. All Manuals Search And Download.
English
11
Remote Control Overview ....................19
Overview of Surround Formats .............22
SETUP
29
Using the RR-1050
Dolby Surround
AUDIO Button
........................................... 19
Dolby Pro Logic II ............................................ 22
Menu Basics .........................................29
Navigation Buttons ............... 29
Programming the RR-1050
Dolby Digital ................................................... 22
PRELOAD Button
MENU/OSD button
ENTER Button
....................................... 19
DTS 5.1
System Status .................................................. 29
Main Menu ...................................................... 30
Display Options................................................ 30
............................. 19
............................................ 19
....................................... 19
.......................................... 19
......................................... 20
...................................... 20
DTS 96/24 ...................................................... 22
DTS Neo:6 ....................................................... 23
6.1 and 7.1 Surround ...................................... 23
DSP Music Modes ............................................. 23
2Ch/5Ch/7Ch Stereo Formats .......................... 23
Other Digital Formats ...................................... 24
ON/OFF Buttons
POWER Button
VOLUME Button
MUTE Button
Configuring Inputs ................................30
Input Setup ...................................................... 30
Multi Input Setup ............................................. 31
Dolby Pro Logic II ............................................ 32
DTS Neo:6 ....................................................... 32
DEVICE/INPUT Buttons
.............................. 20
Automatic Surround Modes ...................24
Manually Selecting Surround Modes ......24
REC Button
................................................ 20
............................................. 20
ZONE Button
Configuring Speakers and Audio ............32
Understanding Speaker Configuration .............. 32
Speaker Setup ................................................. 33
Advance Speaker Setup.................................... 34
Subwoofer Setup ............................................. 34
Test Tone ......................................................... 35
Delay Setup ..................................................... 36
Contour Setup .................................................. 36
Dolby Digital 5.1
Dolby Digital Surround EX ............................... 25
UP/DOWN Buttons
+/– Buttons ............................................. 20
Speaker Selection Buttons ......................... 20
.................................... 20
Dolby Digital 2.0 ............................................. 25
DTS 5.1
DTS 96/24
EQ Button
................................................. 20
............................................. 20
DTS-ES 6.1....................................................... 25
TONE Button
MPEG Multichannel .......................................... 26
Surround Mode Buttons
............................. 20
Digital Stereo
(PCM, MP3, and HDCD) ................................... 26
SUR+ Button
DYN Button
............................................. 20
............................................... 20
Analog Stereo .................................................. 26
Miscellaneous Settings .........................36
Other Options .................................................. 36
Zone 2 Setup ................................................... 37
Default Setup .................................................. 37
Basic Operations ..................................20
Other Settings......................................27
Power and Standby On/Off
Volume Adjustments
Muting the Sound
......... 20
........................... 21
............................... 21
Temporary Speaker Level
Temporary Group Delay
Dynamic Range
..... 27
........ 27
........................... 27
........................ 27
Display Options
.................................. 21
MORE INFORMATION
38
Contour/Tone Settings
Selecting Inputs ....................................21
Cinema EQ
................................................ 28
Troubleshooting ....................................38
Selecting a Source Input
from the Front Panel
Zone 2 Operation .................................28
.......................... 21
......................... 22
Specifications .......................................39
Audio .............................................................. 39
Video ............................................................... 39
General ........................................................... 39
Zone 2 Power On/Off Operation
Controlling Zone 2
............... 28
Selecting a Source
from the Remote
from the Front Panel ....................................... 28
Controlling Zone 2
from the Remote Location
........... 28
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
12
Surround features
About Rotel
Getting Started
• Automatic Dolby Digital® decoding for
Dolby Digital® 2.0, Dolby Digital® 5.1, and
Dolby Digital Surround EX® recordings.
A family whose passionate interest in music
led them to manufacture high fidelity compo-
nents of uncompromising quality founded Rotel
40 years ago. Through the years that passion
has remained undiminished and the family goal
of providing exceptional value for audiophiles
and music lovers regardless of their budget,
is shared by all Rotel employees.
Thank you for purchasing the Rotel RSP-1098
Surround Sound Processor. The RSP-1098 is
full-featured audio/video control center for
analog and digital source components. It fea-
tures digital processing for a wide range of
formats including Dolby Surround®, Dolby
Digital®, DTS® and HDCD® source material.
• Dolby® Pro Logic II® decoding for Dolby
Surround® matrix encoded recordings. Can
be optimized for Music or Cinema sources
plus an emulation mode for the original
Dolby Pro Logic decoding.
Video features
• Automatic decoding for DTS® 5.1 channel,
DTS-ES® Matrix 6.1 channel, DTS-ES® Dis-
crete 6.1 channel, and DTS 96/24 digi-
tal recordings.
The engineers work as a close team, listen-
ing to, and fine tuning each new product until
it reaches their exacting musical standards.
They are free to choose components from
around the world in order to make that prod-
uct the best they can. You are likely to find
capacitors from the United Kingdom and
Germany, semi conductors from Japan or the
United States, while toroidal power transformers
are manufactured in Rotel’s own factory.
• Front panel widescreen color TFT screen
for video or operating menus.
• Wideband 100 mHz video processing for
HDTV signals.
• DTS® Neo:6® Surround modes for deriv-
ing surround channels for 5.1, 6.1 or 7.1
channel systems from 2-channel stereo or
matrix surround recordings. Can be opti-
mized for Music or Cinema sources.
• Full complement of composite, S-Video, and
Component Video inputs and outputs
• Conversion of composite and S-Video sig-
nals to Component Video for output to TV
monitor.
• Automatic decoding for MPEG Multichannel
digital recordings.
Rotel’s reputation for excellence has been
earned through hundreds of good reviews and
awards from the most respected reviewers in
the industry, who listen to music every day.
Their comments keep the company true to its
goal - the pursuit of equipment that is musi-
cal, reliable and affordable.
• Rotel XS (eXtra Surround) automatically en-
sures proper decoding and optimum per-
formance from any multichannel digital
signal on 6.1 and 7.1 channel systems.
Always active in any system with center
back speaker(s), Rotel XS even works with
signals that would not otherwise activate
the proper decoding (such as non-flagged
DTS-ES and Dolby Surround EX discs) or
for which there is no extended surround
decoder (such as DTS 5.1, Dolby Digital
5.1, and even Dolby Pro Logic II decoded
Dolby Digital 2.0 recordings).
Audio features
• Rotel’s Balanced Design Concept combines
advanced circuit board layout, comprehen-
sive parts evaluation, and extensive listening
tests for superior sound and reliability.
All of us at Rotel, thank you for buying this
product and hope it will bring you many years
of enjoyment.
• Individual circuit boards grouped by func-
tion for maximum signal isolation.
• 24-bit/128x oversampling analog-to-digital
converters from AKM and Crystal Semicon-
ductor 24-bit/192 kHz digital-to-analog
converters
• Analog bypass mode for pure 2-speaker
stereo with no digital processing.
• Surround modes for playback of surround
sound material on 2 channel and 3 chan-
nel systems for total compatibility.
• Optical and coax digital inputs and out-
puts.
• Four DSP Music modes.
• MULTI Input for 7.1 channel analog signals
from DVD-A and SACD players. Subwoofer
options include .1 channel pass through
or bass redirect feature with an analog low-
pass filter for a summed subwoofer output
from seven channels.
Other features
• Multi-zone, multi-source capability with
independent input selection and volume.
• User friendly ON-SCREEN DISPLAY (OSD)
menu system with programmable labels for
all inputs. Choice of languages.
“DTS”, “DTS-ES Extended Surround”, “DTS ES® Matrix 6.1”,
and “DTS ES® Discrete 6.1”, and “DTS Neo:6®”are
trademarks of Digital Theater Systems, Inc.
• Automatic HDCD® decoding for signals from
High Definition Compatible Digital® com-
pact discs.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D
symbol are trademarks of Dolby Laboratories.
• Learning remote control to operate the
RSP-1098 and nine other components.
, HDCD®, High Definition Compatible Digital ® and
Pacific Microsonics™ are either registered trademarks or
trademarks of Pacific Microsonics, Inc. in the United States
and/or other countries. HDCD system manufactured under
license from Pacific Microsonics, Inc. This product is covered
by one or more of the following: In the USA: 5,479,168,
5,638,074, 5,640,161, 5,808,574, 5,838,274,
5,854,600, 5,864,311, 5,872,531, and in Australia:
669114. Other patents pending.
• Automatic decoding of digital signals from
MP3 (MPEG-1 Audio Layer 3) players.
• Upgradeable microprocessor software to
accommodate future upgrades.
• Four assignable 12V trigger outputs for
remote turn-on of power amplifiers and other
components.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
13
Unpacking
NOTE: Each source input must be properly
configured using the INPUT SETUP menu of
the OSD menu system. We recommend go-
ing to this menu after connecting each source
to configure it as desired. See Input Setup of
the Setup section for information.
CONNECTIONS
Remove the unit carefully from its packing. Find
the remote control and other accessories. Save
the box as it will protect the RSP-1098 if you
move or need to return it for maintenance.
Although, the RSP-1098’s rear panel looks
daunting, connecting the unit to your system
is straightforward. Each of the source compo-
nents in the system are connected to the
RSP-1098 inputs with a pair of standard RCA
cables for analog audio, a video connection
(composite, S-Video, or Component Video),
and an optional digital audio cable (coax or
optical).
Placement
Place the RSP-1098 on a solid, level surface
away from sunlight, heat, moisture, or vibra-
tion. Make sure that the shelf can support the
weight of the unit.
Analog Audio Inputs &
Outputs
Place the RSP-1098 close to the other com-
ponents in your system and, if possible, on its
own shelf. This will make initial hookup, and
subsequent system changes easier.
The following connections are used for con-
necting analog audio signals to and from the
RSP-1098. See the Making Connections topic
for specific instructions on connecting each type
of component.
NOTE: Surround formats like Dolby Digital and
DTS are digital formats and the RSP-1098
can only decode them when a digital input
signal is available. For this reason, you should
always connect your DVD player’s digital
outputs to the RSP-1098, using either the op-
tical or coax inputs.
The RSP-1098 can generate heat during nor-
mal operation. Do not block ventilation open-
ings. Allow a minimum of 10 cm (4 inches)
of unobstructed space around the unit. If in-
stalled in a cabinet, make sure that there is
adequate ventilation.
NOTE: Normally, the RSP-1098 converts ana-
log inputs to digital signals. All of the digital
processing is available including bass man-
agement, digital crossovers, speaker level and
delay settings and a number surround mode
options including 2-ch stereo, Dolby Pro Logic
II, etc. Alternatively, there is an analog by-
pass surround mode that routes 2-ch analog
inputs directly to the Volume control and
preamp outputs, bypassing the digital pro-
cessing entirely for pure analog stereo.
The outputs of RSP-1098 are sent to the power
amplifier(s) with standard RCA cables from
preamp audio outputs. The video signal from
the RSP-1098 is sent to the TV monitor using
composite video, S-Video, or Component Video
connections.
Don’t stack other components or objects on
top of the RSP-1098. Don’t let any liquid fall
into the unit.
In addition, the RSP-1098 has MULTI input con-
nections for a source component that does its
own surround decoding, remote IR sensor
inputs, and 12V trigger connections for remote
turn-on of other Rotel components.
CD Inputs
A left/right pair of RCA analog audio inputs
for connecting a CD player.
NOTE: Do not plug any system component
into an AC source until all connections have
been properly made.
Tuner Inputs
Video cables should have a 75 ohm imped-
ance. The S/PDIF digital audio interface stan-
dard also specifies a 75 ohm impedance and
all good digital cables adhere to this require-
ment. Do NOT substitute conventional audio
interconnect cables for digital or video signals.
Standard audio interconnects will pass these
signals, but their limited bandwidth reduce per-
formance.
A left/right pair of RCA analog audio inputs
for connecting an AM/FM tuner.
TAPE Inputs
A pair of RCA inputs, labeled TAPE IN, for
connecting the left/right analog audio signals
from an audio tape deck or recording device.
TAPE Outputs
When making signal connections, connect LEFT
channels to LEFT channel jacks and RIGHT chan-
nels to RIGHT channel jacks. All RCA-type
connections on the RSP-1098 follow these stan-
dard color codes:
A pair of RCA inputs, labeled TAPE OUT, for
sending left/right line level analog audio sig-
nals for recording on a tape deck or record-
ing device.
NOTE: These outputs should be connected to
the inputs of the same tape deck connected
to the TAPE IN inputs.
Left channel audio: white RCA jack
Right channel audio: red RCA jack
Composite video: yellow RCA jack
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
14
VIDEO 1–5 Audio Inputs
Preamp Outputs
NOTE: When using a progressive scan or 1080i
video signal from the Component Video in-
puts, the TV monitor cannot display the video
signal and the OSD menus at the same time.
A “progressive” setting in the Display Options
setup menu allows the use of the main OSD
setup menus, even with progressive or HDTV
signals. When the main OSD setup menus are
activated, the progressive scan video input is
interrupted and restored when the OSD menus
are cancelled. The temporary OSD informa-
tion displays (such as volume setting, etc.) are
not displayed.All of the OSD displays are avail-
able on the front-panel TFT screen.
Five pair of RCA inputs, labeled AUDIO IN
(VIDEO IN 1 – 5), provide connections for left/
right analog audio signals from five additional
source components. These inputs have corre-
sponding video inputs and are used for VCRs,
satellite TV tuners, DVD players, etc. However,
they may also be used for additional audio
only components, simply omitting the corre-
sponding video connections.
A group of ten RCA analog audio outputs sends
the RSP-1098’s line level output signals to
external amplifiers and powered subwoofers.
These outputs are variable level, adjusted by
the RSP-1098 volume control. The eight con-
nectors provide output for: FRONT L & R, CEN-
TER 1 & 2, SURROUND L & R, CENTER BACK
CB1 & CB2, and SUBWOOFER 1 & 2.
NOTE: Depending on your system configura-
tion, you may use some or all of these con-
nections. For example, if you only have one
center channel, connect it to the CENTER 1
output. If you only have one center back chan-
nel, connect it to the CB1 output.
VIDEO 1–3 Audio Outputs
Three pair of RCA jacks, labeled AUDIO OUT
(VIDEO OUT 1 – 3), provide connections for
sending line level left/right line level analog
audio signals for recording to a VCR.
Output Conversion: The RSP-1098 con-
verts composite and S-Video signals to Com-
ponent Video signals for output to an NTSC
or PAL standard TV monitor. For maximum con-
venience, connect the RSP-1098 to the TV moni-
tor with Component Video connections. S-Video
signals cannot be converted to composite out-
puts and vice versa.
These connections correspond to the VIDEO
IN 1-3 connections. Make sure that you are
consistent. If you hook up a particular VCR to
the VIDEO 1 inputs, hook up the VIDEO 1 out-
puts to the same VCR.
ZONE 2 Audio Outputs
A pair of RCA inputs, labeled AUDIO OUT/
ZONE 2, sending analog audio signals to an
external amplifier for a remote zone. These
outputs can be configured as either fixed or
variable level using the ZONE 2 SETUP menu.
NOTE: There are no analog audio outputs for
VIDEO 4 & 5. Therefore, in an elaborate sys-
tem, hook up all of the VCRs and recording
devices to VIDEO 1–3 and use VIDEO 4 & 5
for playback only components.
NOTE: When the progressive mode is set to
YES in the DISPLAY OPTIONS setup menu, the
conversion from composite or S-Video to Com-
ponent Video output is only available for the
VIDEO 5 input, not for the VIDEO 1–4 inputs.
NOTE: Only analog input signals are avail-
able at the Zone 2 outputs. Source compo-
nents connected to only the digital inputs are
not available in Zone 2.
NOTE: Video 1–3 can be used for audio-only
tape decks, simply omitting the correspond-
ing video connections.
To configure your system for Zone 2 opera-
tion, connect the left and right Zone 2 outputs
on the RSP-1098 to the left and right channel
inputs of the amplifier powering the remote
speakers, using standard RCA audio cables.
Many digital HDTV monitors adjust scan rates
and other video parameters depending on the
type of input connection. You may wish to make
multiple connections between the RSP-1098
and the TV monitor, switching inputs on the
TV to take advantage of these features.
MULTI Inputs
A set of RCA inputs accept up to 7.1 chan-
nels of analog signals from a DVD-A or SACD
player. There are inputs for FRONT L & R,
CENTER, SUB, REAR L & R, and CENTER BACK
1 & 2.
TFT Display: If you choose to display video
signals on the front panel display, keep in mind
that it can only display signals from sources
connected with composite video connections.
Video Inputs & Outputs
These connections are used for connecting
video signals to and from the RSP-1098. See
the Making Connections section for specific
instructions for each type of component.
These inputs bypass all digital processing in
the RSP-1098 and are routed directly to the
Volume control and preamp outputs
Even if you use Component Video connections,
it is recommended that you also make com-
posite video connections from each source
component to the RSP-1098 so that the sig-
nal from each source component can be dis-
played on the front panel TFT display.
The RSP-1098 provides Composite, S-Video,
and Component Video connections. Composite
video connections simplify system configura-
tion; however, S-Video connections typically
provide better picture quality. Component Video
connections are required for HDTV or progres-
sive scanned DVD video. Be aware of the fol-
lowing implications for the configuration of your
system:
There are two subwoofer options for the MULTI
input. Normally, the .1 channel input is passed
through directly to the subwoofer output. An
optional bass redirect feature duplicates the
7 main channels, sums them, and sends this
mono signal through a 100 Hz analog low
filter to the subwoofer output. This provides
an unaltered analog bypass for the seven main
channels along with a subwoofer signal de-
rived from those channels.
NOTE: The TFT display cannot properly dis-
play progressive scan (480p) signals. When
a DVD player is outputting a progressive scan
signal on Component Video outputs, its com-
posite video outputs may not provide a us-
able signal. In this case, the TFT screen will
not be able to display video from the DVD
player or may display distorted video, even
with a composite video connection.
On Screen Display: The RSP-1098 OSD
system is available on the TV monitor, regardless
of what type of connection is made from the
TV MONITOR outputs to the TV set. The OSD
system is also available in the TFT screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
15
VIDEO 1–5
receivers. Each of these signals is carried by
a separate 75 ohm video cable with RCA
connectors.
ZONE 2 Video Outputs
Composite Video Inputs
The ZONE 2 Video outputs of the RSP-1098
send the video signal to a TV monitor in the
remote zone. Two types of video output con-
nections are provided – RCA composite video
and S-Video.
Five inputs accepts standard composite video
signals from source components using stan-
dard 75 ohm RCA video cables.
NOTE:In progressive scan mode, a DVD player
may not be able to output a usable video
signal on its composite video outputs. In this
case, the TFT screen will not be able to dis-
play video from the DVD player, even with a
composite video input.
VIDEO 1–3
Composite Video Outputs
NOTE: Only composite video input signals are
available at the Zone 2 composite video out-
puts. Only S-Video input signals are avail-
able at the Zone 2 S-Video video outputs.
Three RCA jacks, labeled COMPOSITE VIDEO
OUT 1–3, provide connections for sending
composite video signals for recording on a
VCR or other recording device.
Four sets of inputs, labeled COMPONENT
VIDEO IN 1–4 accept Component video sig-
nals from source components.
These connections correspond to the VIDEO
IN 1-3 connections. Make sure that you are
consistent. If you hook up a particular VCR to
the VIDEO 1 inputs, hook up the VIDEO 1 output
to the same VCR.
Digital Audio
Input & Outputs
The RSP-1098 provides digital connections
which may be used in place of, or in addi-
tion to, the analog audio input and output con-
nections described in the previous sections.
These connections include eight digital inputs
and four digital outputs for recording.
NOTE: When using a progressive scan or
1080i HDTV video signal from the Compo-
nent Video inputs, the TV monitor cannot dis-
play the video signal and the OSD menus at
the same time. A “progressive” setting in the
Display Options setup menu allows the use
of the main OSD setup menus, even with pro-
gressive or HDTV signals. When the main
OSD setup menus are displayed, the progres-
sive video signal is interrupted and restored
when the OSD menus are cancelled. The tem-
porary OSD information displays (such as vol-
ume setting, etc.) are not displayed.
NOTE: The RSP-1098 cannot convert S-Video
or Component Video signals to composite
video. Therefore, only signals received at the
composite video inputs are available at these
outputs.
These digital connections can be used with
any source component that supplies a digital
signal, such as a DVD player, CD player, or
satellite TV tuner.
VIDEO 1–5 S-Video Inputs
Five inputs, labeled S-VIDEO IN 1–5 accept
S-Video signals from source components.
TV Monitor Outputs
NOTE: With a digital connection, the RSP-1098
will be used to decode the signal, rather than
the source component’s internal decoders. In
general, you must use digital connections for
a DVD player or other component that sup-
plies a Dolby Digital or DTS signal; other-
wise the RSP-1098 will not be able to decode
these formats.
VIDEO 1–3 S-Video Outputs
The TV MONITOR outputs of the RSP-1098
send the video signal to your TV monitor. Three
types of video output connections are provided
– RCA composite video, S-Video, and Com-
ponent Video.
Three S-VIDEO jacks, labeled S-VIDEO OUT
1–3, provide connections for sending S-Video
signals for recording on a VCR or other re-
cording device.
The composite video output only sends signals
from composite video inputs to the TV moni-
tor. The S-Video output only sends signals from
S-Video video inputs to the TV. The Compo-
nent Video output converts signals from ANY
type of source input to the TV. If you have
connected all of your source components with
the same type of connection, then you only
need to make one connection from the
RSP-1098 to the TV monitor. If you connect
the RSP-1098 to the TV monitor with Compo-
nent Video connections, you also only need
to make one type of connection because com-
posite and S-Video signals are converted to
Component Video.
These connections correspond to the VIDEO
IN 1-3 connections. Make sure that you are
consistent. If you hook up a particular VCR to
the VIDEO 1 inputs, hook up the VIDEO 1 output
to the same VCR.
Digital Inputs
The RSP-1098 accepts digital inputs from source
components such as CD players, satellite TV
tuners, and DVD players. The built-in digital
processor senses and adjusts to the correct sam-
pling rates.
NOTE: The RSP-1098 cannot convert compos-
ite video or Component Video signals to
S-Video. Only signals received at the S-Video
inputs are available at these outputs.
There are eight digital inputs on the rear panel,
five coaxial and three optical. These digital
inputs can be assigned to any of the input
sources using the INPUT SETUP screen during
the setup process. For example, you can as-
sign the COAXIAL 1 digital input connector
to the VIDEO 1 source and the OPTICAL 2
digital input to the VIDEO 3 source.
VIDEO 1–4
Component Video Inputs
Component Video connections split the video
into three signals – luminance (Y) and sepa-
rate chrominance (CB and CR) signals, allowing
delivery of a reference-quality picture with high
definition signals. Component Video connec-
tions should be used for progressive scan DVD
players and high-definition digital television
NOTE: When the progressive mode is set to
YES in the DISPLAY OPTIONS setup menu, the
conversion from composite or S-Video to Com-
ponent Video output is only available for the
VIDEO 5 input, not for the VIDEO 1–4 inputs.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
12V TRIGGER Connections
NOTE: When using digital connections, you
should also make the analog audio input con-
nections described previously. The analog
connection is necessary to record to an ana-
log recorder in some circumstances or for
ZONE 2 operation
NOTE: The IR signals from the EXT REMOTE
IN jack (as well as those from the ZONE 2/
ZONE 3 REMOTE IN jacks) can be relayed
to source components using external IR emit-
ters or hard-wired connections from the IR
OUT jacks. See the following section for ad-
ditional information.
Many Rotel amplifiers offer the option of turning
them on and off using a 12 volt trigger. These
four connections provide this 12 volt trigger
signal from the RSP-1098. When the RSP-1098
is activated, a 12 volt DC signal is sent to the
amplifiers to turn them on. When the RSP-1098
is put in STANDBY mode, the trigger signal is
interrupted and the amplifiers turn off.
Digital Outputs
IR OUT Jacks
The RSP-1098 has four digital outputs (two
coaxial and two optical) to send the digital
signal from any of the digital inputs to a digi-
tal recorder or outboard digital processor.
When a digital input source signal is selected
for listening, that signal is automatically sent
to both digital outputs for recording.
To use the remote turn on feature, connect one
of the RSP-1098’s 12V TRIG OUT jacks to the
12 volt trigger input of a Rotel amplifier, us-
ing a cable with mono 3.5 mm mini-plugs on
both ends. The +12 V DC signal appears at
the “tip” connector.
The IR OUT 1 & 2 jacks send IR signals re-
ceived at the ZONE REM IN jacks or the EXT
REM IN jack to an infrared blaster or emitter
placed in front of a source component’s IR
sensor. In addition, the IR OUT can be hard-
wired to Rotel CD players, DVD players, or
tuners with a compatible connector.
NOTE: Only digital signals from source com-
ponents are available at these outputs. Ana-
log signals cannot be converted and are not
available at the digital outputs.
NOTE: The 12V Trigger outputs can be config-
ured to turn on only when specific input
sources are activated. See the Input Setup
and Zone 2 Setup menus in the Setup section
of this manual for details.
These outputs are used to allow IR signals from
Zone 2 to be sent to the source components,
or to pass along IR signals from a remote in
the main room when the sensors on the source
components are blocked by installation in a
cabinet.
REM IN Jacks
Other Connections
See your authorized Rotel dealer for information
on IR emitters and repeater systems.
Three 3.5 mm mini-jacks (labeled REM IN,
ZONE 2, and ZONE 3) receive command
codes from an industry-standard infrared re-
ceivers (Xantech, etc.), used when the IR sig-
nals from a hand held remote control cannot
reach the front panel IR sensor.
AC Input
Your RSP-1098 is configured at the factory for
the proper AC line voltage in the country where
you purchased it (USA: 115 volts/60Hz AC
or CE: 230 volts /50 Hz AC ). The AC line
configuration is noted on a decal on the back
of your unit.
Computer I/O
The RSP-1098 can be operated from a com-
puter with audio system control software from
third-party developers. This control is accom-
plished by sending operating codes from the
computer via a hard-wired RS-232 serial con-
nection. In addition, the RSP-1098 can be up-
dated using special software from Rotel.
EXT: The EXT jack is used with an outboard
IR receiver to duplicate the front panel IR sen-
sor. This feature is useful when the unit is in-
stalled in a cabinet and the front panel sen-
sor is blocked or when IR signals need to be
relayed to other components.
Plug the supplied cord into the AC INPUT
receptacle on the back of the unit.
The COMPUTER I/O input provides the nec-
essary network connections on the rear panel.
It accepts standard RJ-45 8-pin modular plugs,
such as those commonly used in 10-BaseT UTP
Ethernet cabling.
NOTE: Memorized settings and video labels
are preserved indefinitely, even if the
RSP-1098 is disconnected from AC power.
ZONE 2 and ZONE 3: These two jacks are
used with IR repeater systems to receiver sig-
nals from IR control systems in remote loca-
tions. For example, remote control signals sent
to the ZONE 2 REM IN control the ZONE 2
features of the RSP-1098 and can be relayed
to other components. Remote control signals
sent to the ZONE 3 REM IN can be used to
select the RECORDING source (the signal
available at the TAPE OUT connections).
Master Power Switch
For additional information on the connections,
cabling, software, and operating codes for com-
puter control or updating of the RSP-1098, con-
tact your authorized Rotel dealer.
The large rocker switch on the rear panel is a
master power switch. When it is in the OFF
position, power to the unit is completely off.
When it is in the ON position, the front panel
STANDBY and remote control ON/OFF but-
tons can be used to active the unit or put it
standby mode.
Consult your authorized Rotel dealer for in-
formation on external receivers and the proper
wiring of a 3.5 mm mini-plugs to fit the REM
IN jacks.
NOTE: After all connections are completed,
the rear panel master power switch should
be put in the ON position and usually left in
that position.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
17
corresponding OUTPUT connections. If you
choose VIDEO 1, make sure that you use
VIDEO 1 inputs and outputs for all analog audio
and video connections.
VCR or Digital Video Recorder
Making Connections
VCR connections can be made to the VIDEO
1, VIDEO 2, or VIDEO 3 inputs and outputs.
If you choose VIDEO 1, make sure that you
use VIDEO 1 inputs and outputs for all ana-
log audio and video connections.
CD Player
Connect the left and right analog outputs from
the CD player to the AUDIO IN jacks labeled
CD (left and right).
Connect a video cable (Composite Video,
S-Video, and/or Component Video) from the
output of the TV tuner to the appropriate VIDEO
IN 1–5 input. For HDTV signals, you should
use Component Video connections. If you
choose S-Video or Component Video connec-
tions, you should also make a standard Com-
posite Video connection so that the TV signals
can be displayed on the RSP-1098 front panel
display.
Connect video cables (Composite Video,
S-Video, and/or Component Video) from the
output of the VCR to the appropriate VIDEO
IN 1–3 input. If you choose S-Video or Com-
ponent Video connections, you should also
make a standard Composite Video connec-
tion so that the TV signals can be displayed
on the RSP-1098 front panel display.
Optional: Connect the digital output of the CD
player to any of the Optical or Coax digital
inputs on the RSP-1098. Use the INPUT SETUP
screen to assign that digital input to the CD
source.
There are no video connections for a CD Player.
Connect the left and right analog outputs from
the TV tuner to the left and right AUDIO IN
jacks corresponding to the VIDEO IN input se-
lected above.
DVD Player
Connect a video cables (Composite Video,
S-Video, and/or Component Video) from the
VIDEO OUT jacks to the VCR inputs.
DVD connections can be made to the VIDEO
1, 2, 3, 4, or 5 inputs. In elaborate systems,
you may wish to use VIDEO 4 or VIDEO 5
for DVD players, since these inputs do not have
corresponding OUTPUT connections. If you
choose VIDEO 1, make sure that you use
VIDEO 1 inputs and outputs for all analog audio
and video connections.
Connect the left and right analog outputs from
VCR to one pair of the AUDIO IN jacks la-
beled VIDEO 1–3.
OPTIONAL: Connect the digital output of the
TV tuner to any one of the OPTICAL IN or
COAXIAL IN digital inputs on the RSP-1098.
Use the INPUT SETUP screen to assign that
digital input to the same video input source
used above. For example, if you use the Video
4 inputs above, assign the digital input to the
VIDEO 4 input.
Connect the left and right AUDIO OUT jacks
for VIDEO 1–3 to the analog inputs on the VCR.
Optional: For a digital recording device, con-
nect the digital output of the recorder to one
of the OPTICAL IN or COAXIAL IN digital inputs
on the RSP-1098. Use the INPUT SETUP screen
to assign that digital input to the VIDEO source
(VIDEO 1, 2, or 3) used for the previous con-
nections. If the recording device accepts a
digital recording input, connect one of the
OPTICAL OUT or COAXIAL OUT connections
to the digital input of the recorder.
Connect a video cable (Composite Video,
S-Video, and/or Component Video from the
output of the DVD player to the appropriate
VIDEO IN 1–5 input. If you intend to use the
progressive scan feature with an HDTV moni-
tor, you should use Component Video connec-
tions. If you choose S-Video or Component
Video connections, you should also make a
standard Composite Video connection so that
the DVD menus can be displayed on the
RSP-1098 front panel display.
AM/FM Tuner
Connect the left and right analog outputs from
the tuner to the AUDIO IN jacks labeled TUNER
(left and right).
There are no digital connections or video
connections for an AM/FM tuner.
DVD-A or SACD Player
Audio Tape Recorder
Connect the digital output of the DVD player
to any one of the OPTICAL IN or COAXIAL
IN digital inputs on the RSP-1098. Use the
INPUT SETUP screen to assign that digital in-
put to the same video input source used above.
For example, if you use the Video 4 inputs
above, assign the digital input to the VIDEO
4 input.
To hook up a DVD-A, an SACD player (or any
external surround decoder), use audio RCA
cables to connect the outputs of the player to
the RCA jacks labeled MULTI INPUT, making
sure that you observe proper channel consis-
tency, i.e. connect the right front channel to
the R FRONT input, etc. Depending on your
system configuration, make six connections
(FRONT L & R, SURROUND L & R, CENTER,
and SUBWOOFER), seven connections (adding
a CENTER BACK connection), or eight con-
nections (adding two CENTER BACK connec-
tions).
Connect the left and right analog outputs from
an audio tape deck to the AUDIO IN jacks
labeled TAPE IN (left and right).
Connect the left/right AUDIO OUT/TAPE OUT
jacks to the inputs on the audio tape deck.
Optional: For a digital recording device, con-
nect the digital output of the recorder to one
of the OPTICAL IN or COAXIAL IN digital inputs
on the RSP-1098. Use the INPUT SETUP screen
to assign that digital input to the TAPE source.
If the recording device accepts a digital re-
cording input, connect one of the OPTICAL
OUT or COAXIAL OUT connections to the
digital input of the recorder.
If you want to record the audio signal from
the DVD player, connect the left and right
analog outputs from the DVD player to the left
and right AUDIO IN jacks corresponding to
the VIDEO IN input selected above.
The MULTI inputs are analog bypass inputs,
passing signals directly through to the Volume
Control and preamp outputs, bypassing all of
the digital processing. The RSP-1098 provides
an optional bass redirect feature that dupli-
cates the seven main channels and passes them
Cable, Satellite, or HDTV Tuner
TV tuner connections can be made to the VIDEO
1, 2, 3, 4, or 5 inputs. In elaborate systems,
you may wish to use VIDEO 4 or VIDEO 5
for TV tuners, since these inputs do not have
No video connections are required for an audio
recording device.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
18
through an analog 100 Hz low pass filter,
creating a summed mono subwoofer output
derived from the main channels. See the IN-
PUT SETUP menu in the Setup section of this
manual for details on bass redirect feature.
Front Panel Overview
The following is a brief overview of the con-
trol and features on the front panel of the
RSP-1098. Details concerning the use of these
controls are provided in subsequent sections
of this manual describing various tasks.
OPERATING
THE RSP-1098
Considering its large number of features, set-
tings, and options, the RSP-1098 is remark-
ably easy to operate. The key to the operat-
ing the RSP-1098 is its system of On-Screen
Displays (OSD) which guide you through
various choices. These OSD menus can ap-
pear on the television monitor and/or on the
front panel TFT color LCD screen.
TV Monitor
Connect the TV MONITOR output to the cor-
responding input on your television monitor,
using composite video, S-Video, and/or Com-
ponent Video cables.
Color TFT Display
In the center of the front panel is a large
widescreen format TFT color LCD display. The
display is used for two purposes: displaying
OSD menus and as a built-in TV monitor for
any composite video signal coming into the
RSP-1098, making it ideal for navigating DVD
menus, monitoring a remote camera, or just
watching TV.
NOTE: The RCA composite video output only
sends signals from RCA composite video
source inputs to the TV monitor. The S-Video
output only sends signals from S-Video video
source inputs to the TV. The RSP-1098
upconverts composite and S-Video signals to
Component Video signals. Therefore, the
Component Video output sends signals from
any source input to the TV.
The RSP-1098 can be operated from the front
panel or the remote control. Front panel con-
trols are unusually simple to use, with just a
few knobs and buttons to guide you through
OSD menu options. The remote control pro-
vides more complete control options.
MENU button
To guide you through the operation of the
RSP-1098, this section of the manual starts with
explaining the basic layout and function of the
front panel and the remote control. Then, we
explain the basic operations such as turning
the unit on and off, adjusting volume, select-
ing a source for listening, etc. Following that
is a detailed explanation of surround sound
modes and how to configure the RSP-1098
for various types of recordings. Finally, there
are instructions for additional features and Zone
2 operations. All of these are features that may
be used in normal use. The last section of the
manual (Configuration) details options that may
be selected during initial setup and configu-
ration of the unit, many of which will be set
once and left untouched.
The MENU button toggles on or off the SYS-
TEM STATUS menu showing the current set-
tings of the RSP-1098. Pressing the ENTER
button on the remote (or the FUNCTION knob
on the front panel) from the SYSTEM STATUS
menu takes you to additional menus for con-
figuring the RSP-1098’s many options. See the
Setup section of the manual for more detail
on the OSD menus.
When configuring the unit, you must specify
either an NTSC or a PAL standard TV moni-
tor. See the Other Options menu in the Setup
section of this manual.
Amplifiers and Powered
Subwoofers
To hook up a powered subwoofer,
connect a standard RCA audio cable from
either the two PREOUT jacks labeled SUB to
the input on the subwoofer’s power amp. Both
SUB outputs provide the same signal.
NOTE: Turn off power to the front panel display
by pressing and holding the MENU button.
DISPLAY Button
To hook up amplifiers, connect an audio
cable from each PREOUT jack to the input of
the amplifier channel that will power the cor-
responding speaker. In a full home theater
system, you will need to make five different
connections in addition to the subwoofer . These
connections are labeled FRONT L &R, CEN-
TER, and REAR L & R. There are two CENTER
jacks, use either jack for a single center channel
or both if you have two center channels
The DISPLAY button provides access to two set-
tings for the front panel TFT screen and OSD
menu displays: selecting a video source for
display on the TFT screen and selecting whether
OSD menus are displayed on the front panel
TFT, the TV monitor, or both.
Throughout this manual, numbers in gray boxes
refer to the RSP-1098 illustration at the front
of this manual. Letters refer to the RR-1050 re-
mote illustration. When both appear, the func-
tion is found on both the RSP-1098 and the
remote. When only one appears, that func-
tion is found only on the RSP-1098 or the re-
mote.
STANDBY Button
The front panel STANDBY button activates or
deactivates the unit. The rear panel master
STANDBY button must be in the ON position
for the remote standby function to operate.
In six or seven channel systems, you will make
one or two additional connections for center
back speaker(s). These jacks are labeled CB1
and CB2. Use CB1 for a single center back
channel.
VOLUME Knob
The large knob at the right side of the front
panel is the master VOLUME control, adjust-
ing the output level of all channels simulta-
neously. In addition, it can be used to adjust
the ZONE 2 volume.
Make sure that you have each output connected
to the correct amplifier channel (front right, left
rear, etc.).
Download from Www.Somanuals.com. All Manuals Search And Download.
English
19
MUTE Button
MODE Button
Programming the RR-1050
PRELOAD Button
Push the MUTE button once to turn the sound
off. An indication appears in the front panel
and on-screen displays. Press the button again
to restore previous volume levels.
Although surround mode selection is gener-
ally automatic, the MODE button on the front
panel can be used (with the FUNCTION knob)
to temporarily override the default surround
mode for a particular input. The available op-
tions depend on the type of source input (digital
or analog) and the type of recording (Dolby
Digital, DTS, PCM stereo, etc.)
The RR-1050 is programmed at the factory to
operate the RSP-1098. Should the AUDIO
command set on your RR-1050 not operate
the RSP-1098, the programming may have
been inadvertently changed. To restore the
RSP-1098 programming, press the recessed
PRELOAD button on the remote with the tip of
a ballpoint pen.
NOTE: Rotating the volume knob also cancels
the muting function.
FUNCTION Knob
Remote Sensor
The large knob at the left side of the front panel
is dual action control for navigating OSD
menus. Rotate the control to the left or right to
change settings on the menus. Push the knob
to enter the new setting.
NOTE: Pushing the PRELOAD button will erase
all custom programming and learned com-
mands, restoring the RR-1050 to its factory
condition.
This sensor receives IR signals from the remote
control. Do not block this sensor.
ZONE 2 LED
A small LED in the upper left portion of the front
panel lights when the remote ZONE 2 feature
of the RSP-1098 is in use.
MENU/OSD button
PATH Button
Push this button on the remote to turn on the
OSD menu system. If the menu system is al-
ready visible, push this button to cancel the
display.
The RSP-1098 can independently select sources
for listening, recording, and use in a remote
Zone 2 location. The PATH button toggles
among listening, recording, and Zone 2 se-
lection modes. In listening mode, input selec-
tion and volume adjustments change the main
listening room. In Zone 2 mode, these adjust-
ments change the remote zone. In recording
(or Zone 3) mode, a source is selected for output
to VCRs or other recorders.
Remote Control Overview
The RSP-1098 includes a full-function learning
remote control that can operate the RSP-1098
plus nine other audio/video components.
The front panel TFT display can be turned off
by pressing and holding the MENU/OSD
button on the remote for three seconds. Briefly
press the MENU/OSD button again to turn
the display back on. The display also turns back
on whenever the STANDBY button on the front
panel or remote is pressed.
A separate manual gives detailed instructions
on programming and using the RR-1050 to
replace all of the remote controls in your sys-
tem. The RR-1050 manual covers many extra
features (such as custom labeling of remote
buttons that appear in its LCD display). To avoid
duplication, we provide only basic informa-
tion about using the RR-1050 to operate the
RSP-1098 in this manual.
SPEAKER Button
ENTER Button
During the setup of the RSP-1098, precise
volume levels adjustments for each speaker
are memorized for the proper playback of
Dolby Digital and other surround sound for-
mats. These default settings will be used each
time you turn on the RSP-1098. The SPEAKER
button on the front panel selects a speaker for
temporary adjustments that remain in effect
only until you change to a different input source
or turn the RSP-1098 off. The actual adjust-
ment is made with the FUNCTION knob.
The ENTER button is used to confirm and
memorize various settings in the setup and
operation of the RSP-1098. Its use is described
in detail in the relevant sections.
Many of the RR-1050 functions duplicate the
front panel controls. For that reason, we cover
the controls on the remote under appropriate
topics throughout this manual. Letters in gray
boxes next to the name of a function refers to
the labeled illustration of the remote at the
front of this manual.
ON/OFF Buttons
The power ON and OFF buttons on the re-
mote provide discrete ON and OFF commands
to activate the unit or put it in standby mode.
The rear panel master POWER switch must
be in the ON position for the remote standby
function to operate.
The SPEAKER button can also be used to make
a temporary adjustment to the group delay
or “lip-synch” delay. Like the speaker settings,
this is a temporary adjustment that overrides
the permanent default setting for a video source
until a different input source is selected or the
unit is turned off.
Using the RR-1050
AUDIO Button
POWER Button
The POWER button on the remote provides
the same basic function as the ON/OFF but-
tons, except in a conventional toggle format.
Press the button once to activate the unit; press
again to put the unit into standby mode.
To operate the RSP-1098 with the remote, make
sure that the AUDIO mode is active by press-
ing the AUD button on the remote before you
start. If one of the other buttons (CD, TAPE,
etc.) is pressed, the remote will control another
component, not the RSP-1098. The AUDIO
mode will stay active until another DEVICE/
INPUT button is pressed.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
20
VOLUME Button
+/– Buttons
Basic Operations
This section covers the basic operating con-
trols of the RSP-1098 and the remote.
The large rocker button is the master VOLUME
control, adjusting the output level of all chan-
nels simultaneously.
This pair of buttons is used to change settings
on a selected line in the OSD menus. Also used
for selecting options in some surround modes.
MUTE Button
Speaker Selection Buttons
Power and Standby On/Off
Push the MUTE button once to turn the sound
off. An indication appears in the front panel
and on-screen displays. Press the button again
to restore previous volume levels.
These three buttons are used to select a speaker
or group of speakers for temporary level ad-
justments.
The rear panel POWER switch on the RSP-1098
is a master power switch. The button must be
pressed IN for the unit to operate. When it is
in the OUT position, the unit is fully off and
cannot be activated from the front panel or
remote control.
EQ Button
NOTE: Pressing the volume buttons on the re-
mote also cancels the muting function.
This button is used to turn on and off the Cin-
ema EQ feature, a high-cut filter useful for older
movie soundtracks.
The STANDBY button on the front panel, the
discrete ON/OFF buttons on the remote, and
the POWER button on the remote function as
a standby switches, activating or deactivating
the unit. In standby mode, minimal power is
supplied to the microprocessor. When the unit
has AC power applied and the rear panel
POWER switch is on, the front panel STANDBY
LED lights, regardless of whether the unit is in
standby mode or activated in the main room.
DEVICE/INPUT Buttons
The ten buttons at the top of the remote have
two functions:
TONE Button
This button is used in setting the Contour ad-
justments. It toggles between high frequency
(HF) and low frequency (LF) modes. Once a
mode is selected, the UP/DOWN buttons are
used to make the adjustments.
Short press: A short press of any button
changes the device that the remote operates,
but does not change the RSP-1098’s input
selection.
Long press: A longer press changes the re-
mote control device and changes the RSP-1098
source input for listening/viewing in the main
room.
Surround Mode Buttons
In normal operation, the rear panel POWER
switch is always left in the ON position and
the RSP-1098 is activated and deactivated using
the front panel STANDBY button or the remote
ON/OFF buttons or the remote POWER but-
ton. The ON/OFF buttons and the POWER
button on the remote provide essentially the
same function with the ON/OFF buttons pro-
viding discrete ON and OFF commands while
the POWER button provides a standard toggle
on/off function.
Five buttons on the remote (2CH, PLC, PLM,
5CH, 7CH) allow direct selection of certain
surround modes: 2-channel stereo, Pro Logic
II Cinema, Pro Logic II Music, 5-channel ste-
reo, or 7-channel stereo. The function of these
buttons varies depending on the type of re-
cording being played. See the Manually Se-
lecting Surround Modes section for detailed
information.
NOTE: A long press of the EXT button changes
the input to the 7.1 channel analog MULTI
INPUT. Pressing theAUD button only changes
the remote device; there is no input source
associated with this button.
REC Button
SUR+ Button
Press this button before a long press of an DE-
VICE/INPUT button to select a source for re-
cording. The signal from the selected source
appears the TAPE OUT connectors.
When using the Zone 2 capability of the
RSP-1098, the standby activation is com-
pletely independent for the main room and
Zone 2. ON/OFF commands sent from the
remote in the main room will not effect Zone
2. Pressing the ON/OFF buttons on a remote
located in Zone 2 will only effect that zone
and not the main room. When the unit is ac-
tivated in ZONE 2, the ZONE 2 LED on the
front panel is lit.
This button is used in conjunction with the +/–
buttons for manual selection of surround modes
and features. See the Manually Selecting Sur-
round Modes section for information.
ZONE Button
DYN Button
Press this button before a long press of an DE-
VICE/INPUT button to select a source for ZONE
2.
Used for selecting the dynamic range control
setting in Dolby Digital surround mode.
UP/DOWN Buttons
There are three available power mode options,
which may be useful in configuring the
RSP-1098 for special system configurations.
See the Other Options menu in the Setupsection
of this manual for additional details on changing
the default standby behavior.
This pair of buttons is used to move the cur-
sor up or down to select lines in the OSD menus.
These buttons are also used in conjunction with
the TONE button to make CONTOUR/TONE
adjustments.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
21
Volume Adjustments
Display Options
input is assigned, the unit will not access a
digital signal, even though one may be avail-
able at the digital input.
The listening volume of the RSP-1098 can be
adjust from the front panel or the remote.
The front panel DISPLAY button provides ac-
cess to two settings of the front panel TFT screen
and OSD menu displays: selecting a video
source for display on the TFT screen and se-
lecting whether OSD menus are displayed on
the front panel TFT screen, the TV monitor, or
both.
By default, the source DEVICE/INPUT buttons
are factory configured to select the following
inputs:
Front Panel: Rotate the front panel VOLUME
knob clockwise to increase the volume, coun-
terclockwise to decrease.
CD:
Analog input
Remote: Press the VOL UP button to increase
the volume; press the VOL DOWN button to
decrease.
Tuner:
Analog input
• To view a video source on the TFT
screen: press the DISPLAY button once.
Then, rotate the FUNCTION knob to se-
lect a source. Available display options are
VIDEO 1–5, SOURCE (the same source se-
lected for listening), or no video display.
Tape:
Analog input
Video 1:
Video 2:
Video 3:
Video 4:
Video 5:
Digital Coaxial 1
Digital Coaxial 2
Digital Coaxial 3
Digital Optical 1
Digital Optical 2
When you adjust the volume, the setting is
shown on the TV monitor and/or the front panel
TFT display. The current volume setting is also
shown on the SYSTEM STATUS OSD screen.
• To change the OSD setting: press the
DISPLAY button two times. Then, rotate the
FUNCTION knob to select an OSD option.
Available options are to view OSD menus
on the TFT/LCD screen, the TV monitor, or
both.
Each source input should be configured us-
ing the INPUT SETUP menu system to use the
desired input type (analog or digital auto-sens-
ing).
NOTE: The front panel VOLUME control can
be used to change the volume in Zone 2.
Press the front panel PATH button three times
to change from the LISTENING to the ZONE
2 control mode as shown by the OSD and/
or TFT display. Turning the VOLUME knob
will then adjust the volume setting for ZONE
2. After 5 seconds, the PATH setting and
VOLUME control revert to normal LISTENING
mode operation.
NOTE: In addition to selecting analog or digital
signals, the configuration options also permit
custom labeling and selection of a default sur-
round mode for each of the eight inputs.
• To shut off power to the TFT screen:
press and hold the MENU/OSD button on
the remote or the MENU button on the front
panel for 3 seconds.
Selecting a Source Input from
the Front Panel
Muting the Sound
Selecting a source input from the front panel
is a two-step process. First choose whether you
are changing the source for LISTENING in the
main room, for RECORDING, or for ZONE
2. Then, select the desired source.
Selecting Inputs
The volume of the RSP-1098 can be turned
off or muted. Push the MUTE button on the front
panel or the remote once to turn the sound
off. A MUTE indication appears in the OSD
and/or TFT displays. Press the MUTE button
again to restore previous volume levels.
Up to three audio sources and five audio/video
sources (Tuner, CD, DVD, VCR, etc.) can be
connected to the RSP-1098. Any of these
sources can be independently selected for lis-
tening/viewing in the main room, for record-
ing, or for listening/viewing in a remote Zone
2 location.
To select a source for LISTENING:
1. Press the PATH button one time for LISTEN-
ING selection.
NOTE: If the TFT screen and TV monitor are
turned off, muting the sound gives no visual
indication, creating a false impression that
the RSP-1098 is not working correctly.
The OSD and/or TFT displays show the name
of the current source selection as it is made.
The labels for all input sources can be custom-
ized to match your components.
2. Rotate the FUNCTION knob to cycle
through the list of sources until you reach
the desired source.
To select a source for RECORDING:
All of the source inputs can be customized using
the OSD configuration menus to accept either
analog signals or digital signals from one of
the eight assignable digital inputs. When a
digital input is assigned, the RSP-1098 checks
for the presence of a digital signal at that in-
put. If a digital signal is present when the source
is selected, it is automatically activated and
the proper surround mode enabled. If no digital
signal is present, the analog inputs for that
source are selected. This auto-sensing is the
preferred configuration for digital source in-
puts such as DVD players. When an ANALOG
1. Press the PATH button two times for RECORD-
ING selection.
2. Rotate the FUNCTION knob to cycle
through the list of sources until you reach
the desired source.
Selecting the “SOURCE” option links the lis-
tening source to the record outputs, record-
ing whatever listening source is selected now
or in the future for recording.
NOTE: See the section on Zone 2 operations
for details of selecting a source for the re-
mote zone.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
22
Selecting a Source from the
Remote
Dolby Surround
The most common use of Dolby Digital in newer
films, in both the film industry and in home
theater, is Dolby Digital 5.1. Instead of encoding
multiple surround channels on a two-channel
recording, Dolby Digital 5.1 records six dis-
crete channels: front left, front center, front right,
surround left, surround right, and a Low Fre-
quency Effects (LFE) channel containing ultra-
low bass signals intended for a subwoofer.
A Dolby Digital decoder extracts the channels
from the digital bitstream, converts them to
analog signals and routes them to the appro-
priate amplifiers and speakers. All channels
provide full frequency response with total sepa-
ration between all channels and large dynamic
range capability. A Dolby Digital 5.1
soundtrack can provide more impressive sur-
round sound than matrix Dolby Surround.
Dolby Pro Logic II
To select a source for LISTENING in the
main room: press and hold one of the DE-
VICE/INPUT buttons for more than one sec-
ond. To select the MULTI INPUT, press the EXT
button.
The most widely available surround sound
format for consumer audio/video is Dolby
Surround®, available on nearly all commer-
cial VHS tapes, many television broadcasts,
and most DVDs. Dolby Surround is the con-
sumer version of the analog Dolby Stereo system
first introduced in the film industry in 1972. It
is a matrix-encoding system that records front
left, front center, front right, and a mono sur-
round channel into a 2-channel stereo record-
ing. During playback, a Dolby Pro Logic® or
Pro Logic II decoder extracts each channel and
distributes it to the appropriate speakers.
NOTE: A short press of a DEVICE/INPUT but-
ton changes the remote control device only,
but does not change the source input.
To select a source for RECORDING: Press
the REC button and then press one of the DE-
VICE/INPUT buttons within 5 seconds.
Alternatively, you can press the REC button and
then use the +/– buttons to scroll through the
available source options. Select any input (CD,
TUNER, TAPE, or VIDEO 1–5). Selecting the
SOURCE option links the recording source to
the input selected for main room listening.
Whatever input is selected for listening is also
sent to the record outputs.
The original Dolby Pro Logic decoder deliv-
ered a mono signal with reduced high-fre-
quency content to the surround speakers. A
more advanced decoder in the RSP-1098,
Dolby Pro Logic II, increases the separation
and frequency response of the surround chan-
nels for significantly improved performance
with Dolby Surround encoded recordings.
Decoding of Dolby Digital 5.1 soundtracks is
automatic. When the RSP-1098 detects a Dolby
5.1 signal on one of its digital inputs, it acti-
vates the proper processing. Keep in mind that
Dolby Digital is only available from digital
sources (a DVD, a LaserDisc, or a Digital TV/
Cable/SAT tuner). Also, you must connect the
source with a digital cable (coax or optical)
to an active digital input on the RSP-1098.
To select a source for Zone 2: Press the
ZONE button and then press one of the DE-
VICE/INPUT buttons within 5 seconds.
Dolby Pro Logic II decoding should used for
any analog recording labeled “Dolby Sur-
round” or any Dolby Digital 2.0 soundtrack.
Dolby Pro Logic II does a superb job deriving
surround sound from conventional 2-channel
stereo recordings, using phase relationships
to extract front, right, center, and surround chan-
nels. A “music mode” makes Pro Logic II an
excellent choice for audio CDs.
Alternatively, you can press the ZONE button
and then use the +/– buttons to scroll through
the available source options. Select any input
(CD, TUNER, TAPE, or VIDEO 1–5). Select-
ing the SOURCE option links the Zone 2 source
to the input selected for main room listening.
Whatever input is selected for the main room
is also sent to the Zone 2 outputs.
NOTE: Many DVDs have a Dolby Digital 2.0
matrix soundtrack as the default, which should
be decoded with Pro Logic II. The Dolby Digi-
tal 5.1 soundtrack may have to be selected
as an option from the setup menus at the be-
ginning of the DVD. Look for a Dolby Digital
5.1 selection under “Audio” or “Languages”
or “Setup Options” when you insert the disc.
Dolby Digital
In 1992, an digital recording system, called
Dolby Digital, was first used in the film indus-
try. Dolby Digital is a recording/playback sys-
tem that uses compression techniques to store
large amounts of audio data efficiently, much
like the JPEG format stores large photographs
in small files on a computer. Because it is
capable of performance beyond that of au-
dio CDs and can tailor its output for a wide
ranges of system configurations, Dolby Digi-
tal is the standard audio format for DVDs and
for digital television broadcasting in the United
States.
DTS5.1
Overview of
Surround Formats
To get the best performance from your
RSP-1098, it helps to understand the many
surround sound formats available today, to
know which decoding process to use for a
particular recording, and how to select it. This
section provides basic background informa-
tion about surround sound formats. The follow-
ing sections provide detailed operating instruc-
tions for automatic and manual selection of
surround modes.
DTS 96/24
DTS® (Digital Theater Systems) is an alterna-
tive digital format competing with Dolby Digital
in both movie theaters and home theater
markets. The basic functions of the DTS sys-
tem are similar to those of Dolby Digital (for
example, 5.1 discrete channels), however the
technical details of the compression and de-
coding processes differ somewhat and a DTS
decoder is required.
The Dolby Digital system can be used to record
up to six discrete audio channels, but can also
be used for fewer. For example, a Dolby Digital
2.0 soundtrack is a digital 2-channel record-
ing of a matrix encoded Dolby Surround
soundtrack.. To play a Dolby Digital 2.0 re-
cording, use Dolby Pro Logic II decoding as
previously described.
A recent extension of the DTS encoding sys-
tem is DTS 96/24. These recordings provide
the performance of a 96kHz sampling rate
while still using actual 48kHz sampling rate
of standard DTS discs.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
23
Like Dolby Digital, DTS can only be used on
a digital recording and, therefore, is only
available for home use on LaserDiscs, DVDs,
or other digital formats. To use the RSP-1098’s
DTS decoder, you must connect your DVD
player to the RSP-1098’s digital inputs.
DTS has added a similar capability for record-
ing this extended surround information called
DTS-ES® 6.1 Matrix. They have also taken it
one step further and developed the capabil-
ity to record this extended surround informa-
tion as a discrete channel in a system called
DTS-ES® 6.1 Discrete.
DSP Music Modes
Unlike all of the formats mentioned above, the
RSP-1098 offers four surround modes that not
part of a specific recording/playback system.
These modes (MUSIC 1–4) use digital signal
processing that adds special acoustic effects
to any signal. DSP processing can be used
with Dolby Surround recordings, Dolby Digi-
tal recordings, CDs, radio broadcasts, or any
other source material; however, typically DSP
settings would be used with source material
for which there is no specific surround decoder.
As with Dolby Digital 5.1, detection and proper
decoding of DTS 5.1 signals is automatic.
All of these systems are extensions of the ex-
isting Dolby Digital 5.1 and DTS 5.1 digital
surround sound formats. Users with one cen-
ter back speaker (a 6.1 configuration) or two
center back speakers (a 7.1 configuration) can
take advantage of this extended surround in-
formation. On traditional 5.1 channel systems,
Dolby Digital Surround EX or DTS-ES 6.1 discs
sound exactly the same as 5.1 channel discs
in each respective format.
NOTE: DVDs with a DTS soundtrack almost
always have it configured as an option to the
standard matrix Dolby Surround format. To
use DTS, you may have to go to the setup
menus at the beginning of the DVD and se-
lect “DTS 5.1” instead of “Dolby Surround”
or “Dolby Digital 5.1”. In addition, many DVD
players have the DTS digital bitstream turned
off by default and cannot output a DTS
soundtrack (even if selected on the disc’s
menu) until you activate the player’s DTS out-
put. If you hear no sound the first time you
attempt to play a DTS disc, go to the DVD
player’s configuration menus and turn on the
DTS bitstream. This is a one-time setting and
need only be done once.
The four MUSIC MODES in the RSP-1098 use
digital delay and reverberation effects to simu-
late progressively larger acoustic environments
with MUSIC 1 being the smallest type of venue
(such as a jazz club) and MUSIC 4 being a
large venue (such as a stadium). Typically used
to add ambience and a sense of space when
listening to music sources or other sources that
lack surround sound encoding.
If you have configured your system with one
or two center back speakers, decoding of
DTS-ES discs is automatic, just as it is with stan-
dard DTS soundtracks. Likewise, decoding of
Dolby Digital Surround EX discs is automatic
with one exception. Some Surround EX titles
do not have the detection “flag” encoded on
the disc. To activate the Dolby Digital Surround
EX features for these discs (or for standard 5.1
channel Dolby Digital discs), you must manu-
ally activate Dolby Surround EX processing.
2Ch/5Ch/7Ch Stereo Formats
The RSP-1098 also provides four modes that
disable all surround processing and deliver
stereo signals to amplifiers and speakers. There
are three options:
DTS Neo:6
The RSP-1098 features a second type of DTS
surround sound decoding: DTS Neo:6. This
decoding system is similar to Dolby Pro Logic
II and is designed for playback of any 2-channel
stereo recording, either matrix-encoded or not.
The Neo:6 decoder can by used with any
conventional 2-channel source such a stereo
TV or FM broadcast or a CD. It can also be
used as an alternative method of decoding
matrix-encoded Dolby Surround recordings or
TV broadcasts. Activate the DTS Neo:6 de-
coding with the DTS Neo:6 button as detailed
later in this section. DTS Neo:6 is not used
with DTS 5.1 digital sources and the button
need not be pressed for those recordings.
2CH Stereo:Turns off the center channel and
all surround channels in the system and deliv-
ers a conventional 2-channel signal to the front
speakers. If the system is configured to route
bass signals from the front speakers to the
subwoofer, this capability remains in effect.
The RSP-1098 also features Rotel XS (eXtra
Surround) processing that automatically ensures
optimum extended surround performance on
6.1 and 7.1 channel systems. The key ben-
efit of Rotel XS is that it works at all times with
all multichannel digital signals, even those that
might not otherwise activate Dolby Digital EX
or DTS-ES surround decoding for the center
back channel(s). Always available when center
back speaker(s) are configured in the system
setup, Rotel XS decodes the surround chan-
nels and distributes the extended surround chan-
nels to the center back speaker(s) in a way
that tends to create a diffuse surround effect.
Rotel XS works with matrix-encoded surround
signals (such as non-flagged DTS-ES and Dolby
Surround EX discs) as well as digital source
material that is not Dolby Surround EX encoded
(such as DTS 5.1, Dolby Digital 5.1, and even
Dolby Pro Logic II decoded Dolby Digital 2.0
recordings).
Analog Bypass: For 2-channel analog in-
puts, there is a special stereo mode that by-
passes ALL of the RSP-1098’s digital process-
ing. The two front speaker receive pure ana-
log stereo full-range signals with no subwoofer
crossover, no delay, no level adjustments, and
no contour adjustment.
5CH Stereo: Distributes a stereo signal to
5.1 channel systems. The left channel signal
is sent, unchanged, the front left and surround
left speakers. The right channel is sent to the
front right and surround right speakers. A mono
sum of the two channels is sent to the center
channel speaker.
6.1 and 7.1 Surround
In 1999, the first Dolby Digital soundtrack was
released to theaters with an additional cen-
ter back surround channel, intended to increase
the directional effects from behind the audi-
ence. This additional surround channel is en-
coded into the two existing surround channels
in Dolby Digital 5.1, using a matrix encod-
ing process similar to that used previously in
Dolby Surround. This new extended surround
capability is called Dolby Digital Surround EX.
7CH Stereo: This mode is the same as 5CH
Stereo described above except that it also
distributes stereo signals to center back
speaker(s) installed in the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
RSP-1098 Surround Sound Processor
Other Digital Formats
MP3: The RSP-1098 also features a decoder
for the digital MP3 (MPEG1- Audio Layer 3)
compression format. MP3 format recordings
are available on the Internet and can be played
on portable MP3 players or some disc play-
ers that can read CD-ROM discs connected
to the RSP-1098’s digital inputs.
NOTE: A digital signal coming into the
RSP-1098 will be recognized and properly
decoded. However, on a DVD with multiple
soundtracks, you must tell the DVD player
which one to send to the RSP-1098. For ex-
ample, you may need to use the DVD’s menu
system to select the Dolby Digital 5.1 or DTS
5.1 soundtrack rather than the default Dolby
Digital 2.0 Dolby Surround soundtrack.
Several other digital formats are not surround
sound formats at all, but rather systems for digital
2-channel recordings.
PCM 2-channel: This is an uncompressed
2-channel digital signal such as that used for
standard CD recordings and some DVD re-
cordings, particularly of older films.
MPEG Multichannel: The RSP-1098 can
decode MPEG Multichannel digital recordings.
Widely used in Europe, this format uses MPEG
data compression to record up to 5.1 chan-
nels of discrete digital audio, similar in func-
tion to the Dolby Digital and DTS formats.
HDCD®: This system uses higher bit rates a
variety of enhancements to improve the sonic
performance compared to standard audio CDs.
These discs, labeled HDCD, can be played
on standard CD players. However, when the
digital signal is decoded using an HDCD
decoder like that in the RSP-1098, they will
provide exceptional musical reproduction.
Additionally, you can configure a default sur-
round mode for each input using the INPUT
SETUP menu (see the Setup section of this
manual). Combined with the auto-detection of
Dolby Digital 5.1 and DTS, this default sur-
round setting makes operation of the RSP-1098
surround modes totally automatic. For example,
if you set Dolby Pro Logic II movie mode as
the default for all of your video inputs, the
RSP-1098 will automatically decode Dolby Digi-
tal 5.1 and DTS soundtracks when they are
played and use Pro Logic II matrix decoding
for all other recordings. For stereo inputs such
as CD and Tuner, you could select STEREO
mode as the default for 2-channel playback
or Dolby Pro Logic II music mode if you pre-
fer to hear music sources in surround sound.
Automatic Surround
Modes
Decoding of digital sources connected to the
digital inputs is generally automatic, with
detection triggered by a “flag” embedded in
the digital recording telling the RSP-1098 what
decoding format is required. For example,
when Dolby Digital 5.1 or DTS 5.1 channel
surround is detected, the RSP-1098 activates
the proper decoding.
DTS Music 5.1 Discs: These discs are a
variation of audio CDs that include a DTS 5.1
channel recording. The RSP-1098 decodes
these discs just like a DTS movie soundtrack
when played on a CD player or DVD player
with a digital output connection.
DVD-A music discs: Taking advantage of
the increased storage capacity of the DVD disc,
new high bit rate multichannel audio record-
ings are available on DVD-A discs. DVD-A discs
may include multiple versions of the record-
ing including standard PCM stereo, Dolby
Digital 5.1, DTS 5.1, and 96kHz/24 bit (or
higher) multichannel recordings using MLP
compression. Several of these formats (stan-
dard PCM, Dolby Digital, and DTS 5.1 can
be decoded by the RSP-1098 when the DVD
player is connected with a digital cable. How-
ever, the existing optical and coax digital
connection standard does not provide suffi-
cient bandwidth for multichannel high sampling
rate MLP recordings. Therefore, DVD-A discs
with these high-resolution audio soundtracks
must be decoded by a the DVD player and
the resulting analog signals sent to the
RSP-1098’s MULTI INPUT.
The unit will also detect DTS-ES Matrix 6.1 or
DTS-ES Discrete 6.1 discs and activate DTS-ES®
Extended Surround decoding. Dolby Digital
Surround EX recordings also trigger automatic
decoding (although not all Surround EX DVDs
have the necessary flag and may require manu-
ally activating Surround EX decoding). Like-
wise, a digital input from an HDCD® encoded
compact disc, a standard CD, a DTS 96/24
disc, or MP3 player will be auto-detected and
properly decoded to 2CH stereo operation.
Manually Selecting
Surround Modes
As described in the previous section, the com-
bination of auto-detection of Dolby Digital and
DTS recordings and setting default surround
modes for each input during the setup of the
RSP-1098 makes operation of surround modes
totally automatic. For many users, this auto-
matic surround mode selection will meet all
of their listening needs.
Rotel XS processing is automatically active in
all systems configured with center back
speaker(s) and will ensure proper extended
surround decoding of all multichannel digital
signals, even those that might not otherwise
trigger the proper extended surround mode.
For users who prefer a more active role in setting
surround modes, buttons on the remote and
the front panel provide manual selection of
surround mode that are not automatically de-
tected or, in some cases, to override an auto-
matic setting.
SACD®: This is a proprietary high-resolution
audio standard for use on SACD compatible
discplayers. Aswithhigh-resolutionDVD-Adiscs,
the bandwidth is too high for today’s digital
connection. Thus, these discs must be decoded
by SACD compatible player, with the output
sent to the RPS-1098’s MULTI INPUTS.
In many cases, the RSP-1098 will also recog-
nizeadigitalsignalwithDolbySurroundencoding
(such as the default soundtrack on many DVDs)
and activate Dolby® Pro Logic II® decoding.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
25
Manual settings available from the front panel
and/or the remote might be used when you
want to play:
Dolby Digital 5.1
Dolby Digital 2.0
Dolby Digital Surround EX
Dolby Digital decoding is auto-detected and
cannot be overridden. You may, however, select
a 2-channel playback, Pro Logic II matrix sur-
round, or Dolby 3-Stereo playback.
Dolby Digital decoding is auto-detected and
cannot be overridden. You may, however, select
a 2 channel downmix of 5.1 channel record-
ings. If the system is configured with center
back speaker(s), you can also force Dolby Sur-
round EX processing on or off.
• Standard 2-channel stereo (left/right speak-
ers only) with no surround processing
• Downmixed 2-channel playback of Dolby
Digital 5.1 or DTS recordings
• To select 2-channel stereo, Pro Logic
II, or 3-Stereo. Repeatedly press the
SUR+ button on the remote until the desired
mode is displayed. On the front panel, press
the MODE button once, then rotate the
FUNCTION knob to select the desired
mode.
• Dolby 3-channel stereo (left/right/center)
of 2-channel recordings.
NOTE: In addition to the options that follow,
you can press the 2CH button on the remote
to toggle between 2-channel downmix and
multichannel playback.
• 5-channel or 7-channel stereo from 2-chan-
nel recordings
• One of four MUSIC modes for DSP con-
cert hall simulation from 2-channel record-
ings
NOTE: You can also direct select 2-channel
stereo or Pro Logic II Cinema modes by press-
ing the 2CH or PLC buttons on the remote.
• On a 5.1 system. Press the SUR+ but-
ton on the remote, then press the +/– but-
tons to change between DD 5.1 channel
or DD 2.0 channel downmix playback. On
the front panel, press the MODE button
once, then rotate the FUNCTION knob to
select 2.0 or 5.1 channel playback.
• Dolby Pro Logic II cinema or music mode
matrix decoding of 2-channel recordings
• To select Cinema, Music, or Emula-
tion option in Pro Logic II mode. Press
the +/– buttons on the remote to select the
desired option. On the front panel, press
the MODE button twice while in Pro Logic
II mode. Then, rotate the FUNCTION knob
to select the option.
• DTS Neo:6 cinema or music mode matrix
decoding of 2-channel recordings
• On a 6.1/7.1 system with a Dolby
Digital 5.1 disc. Press the SUR+ button
on the remote, then use the +/– buttons to
step through four options: DD 5.1 chan-
nel, DD 2.0 channel downmix, DD Surround
EX center back processing, or DD with Rotel
XS center back processing. On the front
panel, press the MODE button while playing
a Dolby Digital source. Then, rotate the
FUNCTION knob to step through the same
options. You should force Surround EX on
for non-flagged discs that are labeled Dolby
Digital Surround EX. Rotel XS processing
of standard 5.1 channel discs will provide
a more diffuse surround effect than the more
highly localized Dolby EX decoding and
will probably be the best 6.1 channel option
for non-Surround EX discs.
• Dolby Digital Surround EX decoding of
Dolby Digital 5.1 channel recordings or
Dolby Digital Surround EX discs that do not
trigger automatic decoding.
NOTE: When playing any Dolby Digital source,
you can select one of three dynamic range
control settings. See the Dynamic Range topic
in the Other Settings section of this manual.
NOTE: DTS, DTS-ES Matrix 6.1, DTS-ES Dis-
crete 6.1, DTS 96/24, Dolby Digital, MP3,
MPEG Multichannel, HDCD (96kHz), and
PCM 2-channel (96kHz) digital signals are
auto-detected and cannot be overridden.
However, you can choose to use Dolby Digi-
tal Surround EX decoding for any Dolby Digi-
tal 5.1 source material. You can also downmix
Dolby Digital 5.1 or DTS 5.1 recordings for
2-channel playback.
DTS 5.1
DTS 96/24
DTS-ES 6.1
DTS decoding is auto-detected and cannot be
overridden. You may, however, select a 2
channel downmix of 5.1 channel recordings
or add Rotel XS center back processing for
5.1 channel discs.
• HDCD (non 96kHZ) and PCM 2-channel
(non 96kHZ) digital signals can be over-
ridden to Dolby Pro Logic II, Dolby 3-Ste-
reo, DTS Neo:6, Music 1 – 4, 5CH Ste-
reo, 7CH Stereo, and Stereo.
NOTE: In addition to the options that follow,
you can press the 2CH button on the remote
to toggle between 2-channel downmix and
multichannel playback.
• On a 6.1/7.1 system with a Dolby
Digital Surround EX disc. Press the
SUR+ button on the remote, then use the
+/– buttons to step through three options:
DD 5.1 channel, DD 2.0 channel down-
mix, or Surround EX center back process-
ing. On the front panel, press the MODE
button while playing a Dolby Digital source.
Then, rotate the FUNCTION knob to step
through the same options. Select the Sur-
round EX option for 6.1 channel playback.
Select the DD 5.1 option to force Surround
EX off for standard 5.1 channel playback.
• Dolby Digital 2-channel Stereo can be over-
ridden to Dolby Pro Logic II, Dolby 3-Ste-
reo, and Stereo.
• On a 5.1 system. Press the SUR+ but-
ton on the remote, then press the +/– but-
tons to change between DTS 5.1 channel
or DTS 2.0 channel downmix playback.
On the front panel, press the MODE but-
ton once, then rotate the FUNCTION knob
to select 2.0 or 5.1 channel playback.
The following topics describe in detail the
manual surround mode options available for
each type of recording
• On a 6.1/7.1 system with a DTS 5.1
or DTS 96/24 disc. Press the SUR+ button
on the remote, then use the +/– buttons to
step through three options: DTS 5.1 chan-
nel, DTS 2.0 channel downmix, or DTS with
NOTE: When playing any Dolby Digital source,
you can select one of three dynamic range
control settings. See the Dynamic Range topic
in the Other Settings section of this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
26
Rotel XS center back processing. On the
front panel, press the MODE button while
playing a DTS or DTS 96/24 source. Then,
rotate the FUNCTION knob to step through
the same options.
Digital Stereo
routed directly to the volume control and the
outputs. It is pure 2-channel stereo, bypass-
ing all of the digital circuitry. None of the bass
management features, speaker level settings,
contour settings, or delay settings are active.
There is no subwoofer output. A full-range signal
is sent directly to two speakers.
(PCM, MP3, and HDCD)
This group of recordings includes any non-Dolby
Digital 2-channel signal from the RSP-1098’s
digital inputs. You can play these recordings
in 2-CH Stereo, Dolby 3-Stereo, 5-CH Stereo,
7-CH Stereo modes. You can also use Dolby
Pro Logic II surround, DTS Neo:6 surround,
or one of the MUSIC 1-4 DSP modes.
• On a 6.1/7.1 system with a DTS-
ES disc. Press the SUR+ button on the re-
mote, then use the +/– buttons to step
through two options: DTS 2.0 channel
downmix or DTS-ES 6.1ch/7.1ch playback.
On the front panel, press the MODE but-
ton while playing a DTS source. Then, ro-
tate the FUNCTION knob to step through
the same options.
The other option converts the analog inputs
to digital signals, passing them through the
digital processors in the RSP-1098. This op-
tion allows all of the features to be active in-
cluding bass management settings, crossovers,
subwoofer outputs, contour settings, etc. In this
mode, you can select several surround modes
including 2-CH Stereo, Dolby 3-Stereo, 5-CH
Stereo, 7-CH Stereo modes. You can also use
Dolby Pro Logic II surround, DTS Neo:6 sur-
round, or one of the MUSIC 1-4 DSP modes.
All of the bass management settings (speaker
size, subwoofer, and crossover) are in effect
with digital stereo inputs.
NOTE: In addition to the options that follow,
you can select 2-channel, Pro Logic II Cin-
ema, Pro Logic II Music, 5-channel stereo, or
7-channel stereo by pressing one of the sur-
round mode buttons on the remote (2CH, PLC,
PLM, 5CH, 7CH).
MPEG Multichannel
MPEG decoding is auto-detected and cannot
be overridden. You may, however, select a 2
channel downmix of 5.1 channel recordings.
If the system is configured with center back
speaker(s), you can also force Rotel XS pro-
cessing on or off.
NOTE: In addition to the options that follow,
you can select Pro Logic II Cinema, Pro Logic
II Music, 5-channel stereo, or 7-channel ste-
reo by pressing one of the surround mode
buttons on the remote (PLC, PLM, 5CH, 7CH).
• To select STEREO mode for 2-chan-
nel digital recordings. Press the 2CH
button on the remote.
NOTE: In addition to the options that follow,
you can press the 2CH button on the remote
to toggle between 2-channel downmix and
multichannel playback.
• To select any other mode for 2-chan-
nel digital recordings. Repeatedly press
SUR+ button on the remote until the desired
mode is displayed. On the front panel, press
the MODE button once, then rotate the
FUNCTION knob to select the desired mode
(including STEREO).
• To select Stereo or Analog bypass
mode for 2-channel analog record-
ings. Press the 2CH button on the remote
to toggle between Stereo (with digital pro-
cessing) or Analog Bypass (no digital pro-
cessing) modes.
• On a 5.1 system. Press the SUR+ but-
ton on the remote, then press the +/– but-
tons to change between MPEG 5.1 chan-
nel or MPEG 2.0 channel downmix play-
back. On the front panel, press the MODE
button once, then rotate the FUNCTION
knob to select 2.0 or 5.1 channel playback.
• Select the Cinema, Music, or Emu-
lation option in Pro Logic II mode.
Press the +/– buttons on the remote to toggle
select the desired option. On the front panel,
press the MODE button twice while in Pro
Logic II mode. Then, rotate the FUNCTION
knob to select the option.
• To select other modes for 2-chan-
nel analog recordings. Repeatedly
press SUR+ button on the remote until the
desired mode is displayed. On the front
panel, press the MODE button once, then
rotate the FUNCTION knob to select the
desired mode (including Stereo and Ana-
log Bypass).
• On a 6.1/7.1 system with an MPEG
5.1 disc. Press the SUR+ button on the
remote, then use the +/– buttons to step
through three options: MPEG 5.1 channel,
MPEG 2.0 channel downmix, or MPEG
with Rotel XS center back processing. On
the front panel, press the MODE button
while playing an MPEG Multichannel
source. Then, rotate the FUNCTION knob
to step through the same options.
• Select the Cinema or Music option
in Neo:6 mode. Press the +/– buttons
on the remote to toggle select the desired
option. On the front panel, press the MODE
button twice while in Neo:6 mode. Then,
rotate the FUNCTION knob to select the
option.
• Select the Cinema, Music, or Emu-
lation option in Pro Logic II mode.
Press the +/– buttons on the remote to toggle
select the desired option. On the front panel,
press the MODE button twice while in Pro
Logic II mode. Then, rotate the FUNCTION
knob to select the option.
Analog Stereo
• Select the Cinema or Music option
in Neo:6 mode: Press the +/– buttons
on the remote to toggle select the desired
option. On the front panel, press the MODE
button twice while in Neo:6 mode. Then,
rotate the FUNCTION knob to select the
option.
This type of recording includes any conven-
tional stereo signal from the RSP-1098’s ana-
log inputs, including analog audio from CD
players, FM tuners, VCRs, tape decks, etc.
Analog stereo inputs require a fundamental
choice about how the signal is routed through
the RSP-1098. One option is the analog by-
pass mode. In this mode, the stereo signal is
Download from Www.Somanuals.com. All Manuals Search And Download.
English
27
Temporary Group Delay
There are three dynamic range settings avail-
able for Dolby Digital recordings:
Other Settings
The SPEAKER adjustments (described above)
can also be used to make a temporary ad-
justment to the group delay or “lip-synch” delay.
Group delay delays the overall audio signal
(to all speakers) by a specified amount to correct
for situations where the video and audio sig-
nals are out of synch. This can occur with
upconverted digital TV signals or when trying
to match a radio broadcast with the video from
a sports event. The settings range from 0 to
500 milliseconds in 5 ms increments.
MAX: full dynamic range
Temporary Speaker Level
MID: slightly reduced dynamic range, roughly
comparable to the signal from a compact disc
The levels of all channels should be calibrated
using the TEST TONE procedure during the
initial setup of the RSP-1098. You can make
a temporary change in the relative volume of
the center, surround, center back, or subwoofer
channels using buttons on the remote control
or the front panel controls. These temporary
adjustments only remain in effect until a dif-
ferent input is selected or until the RSP-1098
is turned off.
MIN: more heavily reduced dynamic range,
but still comparable to the signal from a typi-
cal VHS Hi-Fi recording.
To adjust dynamic range using the
remote:
Press the DYN button repeatedly until the
desired setting appears in the OSD/TFT screen.
This setting remains in effect for all Dolby Digital
program material until it is changed.
Like the speaker settings, this is a temporary
adjustment that overrides the permanent de-
fault setting for a video source until a differ-
ent input source is selected or the unit is turned
off.
To adjust speaker levels using the
remote:
To adjust dynamic range from the front
panel:
1. Pressaselectionbuttonontheremotetoselect
a channel (or pair of channels) for adjust-
ment. Press the C button to adjust the CEN-
TER channel. Press the S button to adjust the
SUBWOOFER channel. Press the R button
to adjust the rear SURROUND or CENTER
BACK channels (each press of the R button
toggles between the SURROUND channels
and the CENTER BACK channels). The se-
lected speaker and its current setting appear
briefly in the display.
To adjust group delay using the re-
mote:
1. While playing a Dolby Digital source, press
the MODE button twice
1. Press the C button on the remote twice.
2. Rotate the FUNCTION control to select the
dynamic range setting.
2. Use the UP or DOWN buttons on the re-
mote to adjust the amount of delay applied
to all channels.
NOTE: The dynamic range compensation fea-
ture is only available in Dolby Digital mode.
The setting is ignored with all other types of
recordings.
To adjust the group delay from the
front panel:
1. Press the SPEAKER button repeatedly un-
til you reach the GROUP DELAY option.
2. Use the UP or DOWN buttons on the re-
mote to adjust the output level of the se-
lected channel(s).
Contour/Tone Settings
The contour adjustment (available only the
remote control) changes the high or low fre-
quency content at the frequency extremes. The
settings can be adjusted up or down by a
maximum of 6dB. Adjustments to the contour
settings are permanent; they remain in effect
until they are readjusted.
2. Rotate the FUNCTION control to adjust the
amount of delay applied to all channels.
To adjust speaker levels from the front
panel.
Dynamic Range
1. Press the SPEAKER button repeatedly until
the desired speaker or group of speakers
is displayed.
Dolby Digital recordings are capable of wide
dynamic range (the difference between the soft-
est and loudest sounds). In some cases, this
may tax amplifiers and/or speakers. In other
cases, you may want to reduce the dynamic
range when listening at low volume levels. This
is particularly useful in order to keep dialog
loud enough to be intelligible while avoiding
excessively loud sound effects. Dolby Digital
dynamic compensation is a sophisticated fea-
ture that allows you to adjust the dynamic range
while still preserving fidelity. The actual amount
of compression relies on instructions embed-
ded in the Dolby Digital recording and var-
ies to best suit the specific program content.
Changing the high frequency contour (HF) in-
creases or decreases the treble. Changing the
low frequency contour (LF) increases or de-
creases the bass content. The settings are shown
on the OSD and/or TFT displays as you ad-
just them.
2. Rotate the FUNCTION knob to change the
level of the selected speaker.
NOTE: If no level adjustment is made for 5
seconds, the levels revert to the default cali-
brated settings.
To adjust the contour settings:
As you select a speaker in the above adjust-
ments, you may notice an addition choice,
“group delay”. See the following for an ex-
planation of this feature.
1. Press the TONE button on the remote. Ei-
ther LF or HF appears in the OSD/TFT
displays, depending on which adjustment
is currently active. Press the TONE button
again to toggle to the other adjustment.
2. Press the UP/DOWN buttons on the remote
to increase or decrease the setting. The
display will revert to normal operation fol-
lowing several seconds of inactivity.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
28
More extensive contour adjustments for all
speakers or for any group of speakers (front,
center, surround, etc.) can also be made from
the Contour Settings OSD menu in the Setup
section of this manual.
This might be useful for sending a line level
signal to a preamp or integrated amp with
its own volume control or to a distribution
amplifier with multiple volume controls.
mode. When the Zone 2 status is displayed,
the OSD and/or TFT screens show the current
source selection and volume in Zone 2 for five
seconds, during which time you can use the
front panel VOLUME control and FUNCTION
knob to change the ZONE 2 settings.
• The RR-1050 remote control supplied with
the RSP-1098 will operate Zone 2 if used
with a repeater system from the remote
zone. It can also be programmed to op-
erate Rotel source components via the
RSP-1098's IR OUT jack.
NOTE: The tone adjustments are available for
all surround modes and inputs, except the
MULTI input and analog bypass mode.
To change the Zone 2 input source:
1. Press the front panel PATH button repeat-
edly until the Zone 2 status appears in the
OSD and/or TFT screen.
Cinema EQ
• Any source component connected to the
RSP-1098's analog inputs can be sent to
the Zone 2 outputs. ZONE 2 operates in-
dependently of the main room. You can
select a different source or adjust Zone 2
volume without affecting the MAIN outputs
in any way.
The EQ button (remote only) activates or de-
activates a special CINEMA EQ setting. This
equalization may be desirable for playback
of movie source material to compensate for
the acoustic differences between a commer-
cial cinema and a home theater environment
by reducing the high-frequency content.
2. Within 5 seconds, rotate the FUNCTION
knob to select a new source for Zone 2.
The name of the selected source appears
in the display. Selecting OFF instead of a
an input deactivates Zone 2.
3. Following 5 seconds with no commands,
the RSP-1098 reverts to normal operation.
• Avoid sending the same infrared command
to the RSP-1098 front panel sensor and a
Zone 2 repeater at the same time. This
means that Zone 2 must be in a different
room from the RSP-1098.
The EQ setting is independent for each source
input. Using the button only changes the set-
ting for the currently active source input.
To change the Zone 2 volume:
1. Press the front panel PATH button repeat-
edly until the Zone 2 status appears in the
OSD and/or TFT screen. Make sure that
Zone 2 is ON.
Zone 2 Operation
Zone 2 Power On/Off
Operation
2. Within 5 seconds, adjust the volume con-
trol to change the Zone 2 output level. The
new setting appears in the display.
The RSP-1098 provides Zone 2 multi-room
capability, allowing you to enjoy music and
operate the system from a second room. From
the remote location, you can select a source
component (independent from the source play-
ing in the main room), adjust the volume level
in the remote zone, and operate the source
components.
Once master power is applied to the unit by
pressing the rear panel POWER switch but-
ton, the RSP-1098 provides independent power
on/off operation for both zones. Pressing the
remote control ON/OFF buttons in the main
room activates or deactivates the RSP-1098
in the main room only and has no effect on
Zone 2. Conversely, activating or deactivat-
ing Zone 2 has no effect on the main listen-
ing room. However, placing the rear panel
master POWER switch in the OFF position com-
pletely shuts off the unit, for both zones.
3. Following 5 seconds with no commands,
the RSP-1098 reverts to normal operation.
Controlling Zone 2 from the
Remote Location
To use the Zone 2 capability, you need addi-
tional components: a pair of speakers installed
in the remote zone, an amplifier to drive them,
an optional TV monitor for video signals, and
a third-party IR repeater system.
With a properly configured IR repeater sys-
tem, you have full control of Zone 2 using an
RR-1050 remote from the Zone 2 location. You
can select and operate a source, adjust the
volume, and turn Zone 2 on or off. Whatever
commands you send from the RR-1050 will
change Zone 2 and only Zone 2, just as if
you were controlling a totally independent
audio system in that room. These changes will
have no effect on the main listening room.
NOTE: For proper power on and off opera-
tion with Zone 2, the RSP-1098’s power mode
should be set to the factory default DIRECT
setting or to the STANDBY setting using the
Other Options menu described in the Setup
section of this manual.
Zone 2 can be controlled from the main room
using RSP-1098’s front panel PATH button. Op-
eration from the remote zone requires the in-
stallation of an infrared repeater system
(Xantech, Niles, etc.) which relays infrared
remote control commands from Zone 2 to the
ZONE REM IN connector on the back of the
RSP-1098.
To turn Zone 2 on or off, press the ON/OFF
buttons on the remote. To adjust the volume
in Zone 2, press the VOLUME buttons on the
remote. To select a different analog input source,
press one of the DEVICE/INPUT buttons on
the remote.
Controlling Zone 2
from the Front Panel
Several points to keep in mind about the Zone
2 function:
You can control Zone 2 from the front panel
of the RSP-1098 – activate or deactivate Zone
2, change input sources, and adjust the vol-
ume. Controlling Zone 2 from the front panel
is accomplished by pressing the PATH repeat-
edly until ZONE 2 status information is dis-
played on the OSD and/or TFT screens. This
temporarily puts the RSP-1098 in Zone 2 control
• There are two options for the Zone 2 out-
put level, selectable from the OSD configu-
ration menu. VARIABLE output provides full
adjustment of the volume level. FIXED out-
put disables the Zone 2 volume control with
theoutputpermanentlysettoaspecifiedlevel.
NOTE: The volume adjustment is only avail-
able if the Zone 2 outputs are configured to
use VARIABLE levels. With FIXED levels, the
volume control for Zone 2 is disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
29
System Status
Menu Basics
SETUP
SYSTEM STATUS
LISTEN:Tuner
VID INPUT:Video 1
RECORD:Source
MODE:Dolby Digital
INPUT:Coaxial 2
VOLUME:65
ZONE 2:Off
SPEAKERS:FR CNT SUB FL
SR CB1 CB2 SL
The RSP-1098 features two types of informa-
tion displays to help operate the system. The
first consists of simple status displays that appear
on the TV screen and/or front panel TFT screen
whenever primary settings (Volume, Input, etc.)
are changed. These status displays are self-
explanatory.
Navigation Buttons
The following remote control buttons are used
to navigate the OSD menu system:
L
GUIDE
MENU
M
The SYSTEM STATUS menu provides a snap-
shot of the current system settings and a start-
ing point for reaching all other screens and
menus. This screen appears when you press
the remote MENU/OSD or front panel MENU
button and displays the following information:
A more comprehensive ON-SCREEN DISPLAY
(OSD) menu system is available at any time
by pressing the MENU/OSD button on the
remote or the front panel MENU button. These
OSD menus guide you through the configu-
ration and setup of the RSP-1098. In general,
the settings made in the configuration process
are memorized as default settings and need
not be made again for normal operation of
the unit.
C
J
UP
OSD
K
C
-
ENT
DWN
+
C
PREV CH
S
R
SEARCH –
SEARCH +
LISTEN: the input source selected for listen-
ing.
L
VID INPUT: the video source selected for
viewing. Can be VIDEO 1–5 or OFF (no video)
as selected on the INPUT SETUP menu. Typi-
cally, the video source matches the audio from
listening source; however a different video input
can be selected.
MENU/OSD button
: Press to display
The OSD menus can be displayed on the TV
monitor, the front panel TFT screen, or both.
This selection can be changed using the DIS-
PLAY OPTIONS menu later in this section.
the SYSTEM STATUS screen. From the SYSTEM
STATUS screen, press the ENTER button to dis-
play the MAIN MENU screen which has links
to all other menus. If a menu is already vis-
ible, push this button to cancel the display. The
MENU button on the front panel provides the
same function.
NOTE: We recommend displaying the OSD
menus on the TFT screen for system setup.
The OSD menus will be available for display
on the TFT screen, regardless of source input
and video output connections and whether
or not a source is actually playing.
RECORD: the source selected for recording
from the VIDEO and AUDIO outputs.
MODE: the current surround sound mode.
DOWN/UP Buttons
and down in the lists of menu items that ap-
pear on the OSD screens.
:Press to move up
INPUT:the input selected for the current source:
Optical Digital, Coaxial Digital, Analog, etc.
The OSD menus can be configured to display
several different languages. The default English
version of all the menus is shown at the front
of this manual. If your language is available,
those menus will be shown in the following
instructions. If you would like to change from
the default English language before proceed-
ing, go to the instructions for the OTHER OP-
TIONS menu later in this manual. From this
menu, you can change the language display.
+/– Buttons
rent settings for a selected menu item on OSD
screens.
: Press to change the cur-
VOLUME: the current volume setting.
ZONE: the current status of ZONE 2, ON or
OFF.
ENTER Button
: From the SYSTEM STA-
SPEAKERS: highlights the speakers that are
currently configured for the system (front right,
center, subwoofer, front left, surround left, center
back 1, center back 2, and surround right)
TUS screen, press ENTER to display the MAIN
MENU screen. From any other OSD screen,
press ENTER to confirm a setting and return
to the MAIN menu.
No changes can be made using this screen;
it only provides information. To go to the rest
of the menus, press the ENTER button to go
to the MAIN menu. Press the MENU/OSD
button on the remote to cancel the display and
return to normal operation.
NOTE: The SYSTEM STATUS screen appears
for five seconds when the unit is turned on
and automatically turns off.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
30
Main Menu
on the TV monitor by interrupting the progressive
scan video signal and restoring it after the OSD
menus are cancelled. Choose the YES option
for progressive scan or HDTV video signals
(480p, 720p, 1080i) at the component video
inputs. Choose the NO option if you are us-
ing standard interlaced video signals (480i).
ing source; however a different video input
can be selected. For audio only sources (such
as a CD player), you would typically specify
OFF so that no video is displayed.
MAIN MENU
INPUT
DELAY
SUB SETUP
DISPLAY
OTHER
SPEAKER
TEST TONE
ZONE 2
CONTOUR
DEFAULT
INPUT LABEL: The seven-character labels for
the all eight inputs can customized. Place the
highlight on this line to begin labelling. The
first character in the label will be flashing.
EXIT
NOTE: When the progressive mode is set to
YES, the conversion from composite or S-
Video to Component Video output is only
available for the VIDEO 5 input, not for the
VIDEO 1–4 inputs.
1. Press the +/– buttons on the remote or rotate
the FUNCTION knob on the front panel
to change the first letter, scrolling through
the list of available characters.
The MAIN MENU provides access to ten OSD
screens for various configuration options. MAIN
MENU is reached by pressing the ENTER button
from the SYSTEM STATUS menu described
above or from most other menus. To go to the
desired menu, move the highlight using the
UP/DOWN and +/– buttons on the remote
and press the ENTER button. Press the MENU/
OSD button on the remote to cancel the dis-
play and return to normal operation.
OSD OUTPUT: Select where the OSD menus
are displayed: on the TFT screen only, the TV
monitor only, or both. Available options are
SCREEN+MON, SCREEN, and MONITOR.
2. Press the ENT button on the remote or press
the FUNCTION knob on the front panel
to confirm that letter and move to the next
position.
3. Repeat steps 1 and 2 until all seven char-
acters (including blank spaces) have been
completed. The final press of the ENT button
saves the new label.
Configuring Inputs
Display Options
A key step in setting up the RSP-1098 is to
configure each source input using the INPUT
SETUP screens. Configuring the inputs allows
you to set defaults for a number of settings
including the type of input connector, the desired
surround mode, custom labels that appear in
the displays when a source is selected, and
many more. The following OSD menus are used
to configure the inputs.
INPUT: assigns a physical input connection
to use as the default for the source displayed
in the first line of the menu. The options are
ANALOG input, three OPTICAL digital inputs
(OPTICAL 1–3), and five COAXIAL digital in-
puts (COAXIAL 1–5).
DISPLAY OPTIONS
DISPLAY SOURCE:Off
CONTRAST:+ 5
BRIGHTNESS:- 5
PROGRESSIVE:No
OSD OUTPUT: SCREEN+MON
When a digital input is the default, the unit
will check for a digital signal when the INPUT
SOURCE is selected. If no digital signal is
present, the unit will automatically revert to the
analog input.
MAIN MENU
Input Setup
The DISPLAY OPTIONS menu provides access
to settings for the front panel TFT screen: se-
lecting a video source for display, picture quality
adjustments, setting the progressive scan mode,
and selecting whether OSD menus are dis-
played on the front panel TFT, the TV moni-
tor, or both.
INPUT SETUP
LISTEN:CD
VID INPUT:Video 1
INPUT LABEL:_______
INPUT:Coaxial 2
When an ANALOG input is the default, the
unit will not access a digital signal, even though
one may be present at the digital input; thus,
the ANALOG setting forces the unit to use an
analog signal. Assigning a digital input (with
its auto-sensing) is generally the preferred con-
figuration for any source with a digital output.
CINEMA EQ:Off
12V TRIGGER:1
DEFAULT MODE:Dolby 3 Stereo
GROUP DELAY:200ms
DISPLAY SOURCE: Select a video source
(composite video only) for display on the TFT
screen. Available display options are VIDEO
1–5, SOURCE (the same source selected for
listening), or OFF no video display.
MAIN MENU
The INPUT SETUP menu configures the source
inputs and is reached from the MAIN menu.
The screen provides the following options, se-
lected by placing the highlight on the desired
line using the UP/DOWN buttons:
NOTE: If a source connected to a digital input
is selected, that signal will automatically be
sent to both digital outputs for recording.
CONTRAST: Adjust the contrast (white level)
of the TFT screen up or down.
CINEMA EQ: The RSP-1098 includes a CIN-
EMA EQ feature which reduces the high-fre-
quency content of movie soundtracks to simulate
the frequency response of a large movie the-
ater and/or eliminate sibilance. You can turn
the CINEMA EQ on or off as the default set-
ting for the selected input using this menu
choice. In general, this setting should be OFF
for most source inputs, unless you are consis-
tently bothered by excessively bright sound from
movie soundtracks.
BRIGHTNESS: Adjust the brightness (black
level) of the TFT screen up or down.
LISTEN: changes the current listening input
source (CD, TUNER, TAPE, VIDEO1–5, & EXT).
Changing this input also allows you to select
a specific input for configuring.
PROGRESSIVE: The OSD menus cannot be
displayed on the TV monitor when progres-
sive scan or 1080i HDTV video signals are
being used at the Component Video inputs.
This setting enables a feature that allows the
display of the main OSD setup menus (but not
the information displays such as volume, etc)
VID INPUT: select the video source to be
displayed on the TV monitor with the listen-
ing source specified on the first line. Can be
VIDEO 1–5 or OFF (no video). Typically, the
video source matches the audio from listen-
Download from Www.Somanuals.com. All Manuals Search And Download.
English
31
12V TRIGGER: The RSP-1098 has four 12V
trigger outputs (labeled 1, 2, 3, and ZONE2)
that supply a 12V DC signal to turn on Rotel
components and other components as needed.
This menu item turns on specific 12V trigger
outputs whenever the indicated source is se-
lected. For example, you set up the VIDEO 1
input to turn on the 12V trigger for your DVD
player. The options for this menu item are:
1/2/3/1+2/1+3/2+3/ALL/NO.
In some cases, the default setting can be manu-
ally overridden by the front panel MODE button
or the SUR+ button on the remote. See the
Manually Selecting Surround Modes section
of this manual for more information on which
settings can be overridden.
Multi Input Setup
INPUT SETUP
LISTEN:Multi Input
VID INPUT:Video 1
INPUT LABEL:_______
12V TRIGGER:1
LFE REDIRECT:On
Two of the default surround mode settings
available on this menu offer additional choices.
Dolby Pro Logic II decoding offers a choice
of CINEMA, MUSIC, or EMULATION settings.
DTS Neo:6 decoding offers a choice of CIN-
EMA or MUSIC settings. When either Dolby
Pro Logic II or DTS Neo:6 is selected with this
menu item, the current setting choice will also
be displayed. In addition, the function of the
ENTER button changes, taking you to a sub-
menu where you can change the settings and/
or additional parameters for Dolby Pro Logic
II or DTS Neo:6 decoding. See the following
section for details.
MAIN MENU
When the MULTI INPUT source is selected on
the INPUT SETUP menu, the available options
change to reflect the fact that these inputs are
direct analog inputs and bypass the RSP-1098’s
digital processing. The INPUT, CINEMA EQ,
and DEFAULT MODE options are not available
since these are all digitally implemented fea-
tures.
DEFAULT MODE: The DEFAULT MODE set-
ting allows you to set a default surround sound
mode for each source input. The default set-
ting will be used unless the source material
triggers automatic decoding of a particular type
or unless the default setting is temporarily over-
ridden by the front panel or remote surround
mode buttons.
The VID INPUT, INPUT LABEL, and 12V TRIG-
GER options are still available and work as
described on the previous menu.
NOTE: Default surround modes are stored in-
dependently for the analog and digital inputs
for each source.
GROUP DELAY: Also known as “lip-sync”
delay, this setting delays the audio signal for
an input by the specified amount to match the
video input. This feature can be useful when
the video signal is delayed more than the audio
signal as sometimes happens with upconverted
digital TV processors or when trying to match
a radio broadcast with the video from a sports
event.
One additional option, LFE REDIRECT, provides
an alternative bass management configura-
tion. Typically, the eight channels of the MULTI
INPUT are configured as pure analog bypass
signals, going straight from the inputs to the
volume control and the preamp outputs, by-
passing all of the digital processing. There are
no crossovers and no bass management; there-
fore, whatever signal goes into the subwoofer
channel will be sent to the subwoofer preamp
output.
Options for the default surround modes are:
Dolby Pro Logic II, Dolby 3 Stereo, Music 1,
Music 2, Music 3, Music 4, 5ch Stereo, 7ch
Stereo, PCM 2 Channel, DTS Neo:6, Bypass
(for analog input only), and Stereo.
NOTE: The following types of digital discs or
source material are generally detected auto-
matically and the proper decoding activated
with no action or setting required: DTS, DTS-ES
Matrix 6.1, DTS-ES Discrete 6.1, Dolby Digi-
tal, Dolby Digital Surround EX, Dolby Digital
2-channel, MPEG Multichannel, PCM 2-Chan-
nel, PCM 96kHz, MP3, HDCD, and HDCD
96kHz.
The range of available settings is from 0ms
to 500ms, in 5ms increments. The setting is
individually stored for each input and is the
default group delay each time that input is se-
lected. The setting can be temporarily over-
ridden from the front panel or the remote.
This configuration may not be ideal for multi-
channel systems configured with high-pass
speakers, redirecting bass to a powered sub-
woofer. An option, called LFE REDIRECT, sends
the seven main channels directly to the out-
puts as usual. In addition, it takes a duplicate
copy of these seven channels, combines them
into mono, and routes them through a 100
Hz analog low-pass crossover to the subwoofer
preamp output. This creates a summed mono
subwoofer signal, derived from the seven main
channels of the MULTI INPUT.
OPTIONS: This selection is only visible when
Pro Logic II or Neo:6 surround mode is selected.
Highlight this line and press ENTER to go to
submenus with additional options for these
surround modes. See below.
Since Dolby Digital 5.1 and DTS sources are
detected and decoded automatically, the de-
fault setting typically tells the RSP-1098 how
to process a 2-channel stereo signal. For ex-
ample, you might have your CD input default
to 2-channel stereo, DVD and VCR inputs default
to Dolby Pro Logic II processing for matrix-
encoded Dolby surround material, and TUNER
input default to one of the MUSIC modes.
To return to the MAIN menu from the INPUT
SETUP menu (except when Dolby Pro Logic II
or DTS Neo:6 is selected in the SURR MODE
field), press the ENTER button. Press the MENU/
OSD button on the remote to cancel the menu
display and return to normal operation.
Use the LFE REDIRECT off for the pure analog
bypass configuration. Use the LFE REDIRECT
on setting to derive the mono summed sub-
woofer output.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
32
Dolby Pro Logic II
• CENTER WIDTH:The Center Width option
allows you to spread the signal intended for
the center speaker to the left and right front
speakers, wideningtheperceivedsoundfield.
There are eight incremental settings from 0
to 7. With the default setting of 0, there is
nocenterwidthspreadingandallofthecenter
channel information is sent to the center
speaker. The maximum setting of 7 shifts all
of the center channel signal to the left and
right speakers, essentially muting the center
speakerandmaximizingthesoundfieldwidth.
Other settings provide incremental steps be-
tween the two extremes.
Configuring
Speakers and Audio
This section of the setup process covers items
concerning audio reproduction such as the
number of speakers, bass management includ-
ing subwoofer crossovers, establishing equal
output levels for all channels, delay settings,
and tone contour settings.
DOLBY PRO LOGIC II
MODE:Music
OPTIONAL PARAMETERS
PANORAMA:Off
DIMENSION:3
CENTER WIDTH:0
INPUT SETUP MENU
When Dolby Pro Logic II is selected as the
default surround mode on the INPUT SETUP
menu, there are additional settings and pa-
rameters to optimize the surround decoding
for music or movie soundtracks. Dolby Pro Logic
II uses matrix decoding algorithms to derive
a center channel and surround channels from
2-channel source material.
Understanding Speaker
Configuration
Home theater systems vary in the number of
speakers and the bass capabilities of those
speakers. The RSP-1098 offers surround modes
tailored to systems with various numbers of
speakers and bass management features which
send bass information to the speaker(s) best
able to handle it – subwoofers and/or large
speakers. For optimum performance, you must
tell the RSP-1098 the number of speakers in
your system and how bass should be distrib-
uted among them.
When you have completed all the desired
adjustments, highlight the INPUT SETUP MENU
line at the bottom of the screen and press the
ENTER button to return to the INPUT SETUP
menu (or just press the ENTER button).
The first line of the Dolby Pro Logic II sub-menu
selects one of three types of matrix decoding:
CINEMA, MUSIC, or EMULATION modes. Use
the +/– buttons on the remote to select a mode.
DTS Neo:6
DTS Neo:6
Select CINEMAto optimize for Dolby Surround
encoded movie soundtracks including in-
creased surround separation and full-bandwidth
surround channel frequency response.
MODE:Cinema
NOTE: There are two types of bass in a sur-
round system. The first is bass recorded in each
of the main channels (front, center, and sur-
round). This bass is present in all recordings
and soundtracks. In addition, Dolby Digital 5.1
and DTS 5.1 recordings may have a Low Fre-
quency Effects (LFE) channel – the .1 channel.
This LFE channel, typically played by a sub-
woofer, is used for effects such as explosions
or rumble. The use of the LFE channel will vary
from soundtrack to soundtrack. Recordings that
are not encoded in Dolby Digital or DTS do
not have the LFE channel.
Select EMULATION for decoding that emu-
lates the original Dolby Pro Logic system. You
may prefer this option for older soundtracks
that are not of optimum audio quality. EMU-
LATION mode reduces the high-frequency
response and separation of the surround chan-
nels and may increase the delay setting.
INPUT SETUP MENU
When DTS Neo:6 is selected as the default
surround mode on the INPUT SETUP menu,
there are additional option settings and pa-
rameters available to optimize the surround
decoding for various types of recordings, music
or movie soundtracks. DTS Neo:6 uses ma-
trix decoding algorithms to derive a center
channel and surround channels from 2-chan-
nel source material.
Select MUSIC to optimize for musical record-
ings. When the MUSIC mode is selected, three
additional parameters will be available on the
OSD screen. Use the UP/DOWN buttons on
the remote to select a parameter. Use the +/
– buttons to change the selected parameter
as follows:
The following configuration instructions refer to
LARGE and SMALL speakers, referring more
to their desired bass configuration than their
physical size. Specifically, use the LARGE set-
ting for speakers that you want to play deep
bass signals. Use the SMALL designation for
speakers that would benefit from having their
bass sent to more capable speakers. The bass
management system redirects bass information
away from all SMALL speakers and sends it to
the LARGE speakers and/or the SUBWOOFER.
It may be useful to think of LARGE as “full-range”
and SMALL as “high-pass filtered.”
In DTS Neo:6 surround mode, there will only
be one choice available on the sub-menu:
selecting CINEMA or MUSIC modes. Use the
+/– buttons on the remote to change the set-
tings.
• PANORAMA: The Panorama option
extends the front stereo image to include
the surround speakers for a dramatic “wrap-
around” effect. The options are OFF or ON.
• Select CINEMA to optimize the DTS Neo:6
decoding for movie soundtracks.
• DIMENSION: The Dimension option al-
lows you to gradually adjust the soundfield
towards the front or towards the rear. There
are seven incremental settings from 0 to
6. A setting of 0 shifts the soundfield to-
wards the rear for maximum surround ef-
fect. A setting of 6 shifts the soundfield to
the front for minimum surround effect. The
default setting of 3 provides a “neutral”
balance between the two extremes.
• Select MUSIC to optimize the DTS Neo:6
decoding for musical recordings.
When you have completed the setting, high-
light the INPUT SETUP MENU line at the bot-
tom of the screen and press the ENTER but-
ton to return to the INPUT SETUP menu (or just
press the ENTER button).
Four typical examples of the many possible
system configurations illustrate the principles
behind bass management:
Download from Www.Somanuals.com. All Manuals Search And Download.
English
33
• Five LARGE speakers and sub-
woofer: This system requires no bass re-
direction. All five speakers play the nor-
mal bass recorded in their respective chan-
nels. The subwoofer plays only the LFE
channel bass. Depending on the
soundtrack, there may be minimal use of
the LFE channel, so the subwoofer would
be under utilized. Meanwhile the normal
bass places higher demands on the capa-
bilities of the other speakers and the am-
plifiers driving them.
LARGE and SMALL configurations is that
(the surround modes will automatically divide
all center channel information equally between
the two front speakers, creating a phantom
center channel).
the bass response may not be as consis-
tent from channel to channel as it might
be with the all SMALL configuration.
SURROUND SPEAKERS (large/small/
none): Select the LARGE setting (not avail-
able with SMALL front speakers) to have the
surround speakers play low bass (full-range).
If your rear speakers have limited bass capa-
bility or if you would prefer that the bass go
to a subwoofer, use the SMALL setting (high-
pass). If your system has no rear surround speak-
ers, select the NONE setting (surround chan-
nels are added to the front speakers so none
of the recording is lost).
NOTE: As an alternative configuration with a
satellite/subwoofer package as the front
speakers, follow the speaker manufacturer’s
instructions, connecting the high-level inputs
of the powered subwoofer directly to the front
speaker outputs of the RSP-1098 and con-
necting the satellites to the subwoofer’s own
crossover. In this arrangement, the speakers
would be classified as LARGE and the sub-
woofer setting would be OFF for all surround
modes. No information is lost during play-
back because the system redirects bass infor-
mation to the front LARGE speakers. While
this configuration ensures proper satellite
speaker operation by using the speaker’s own
crossovers, it has some disadvantages in terms
of system calibration and would generally not
be the preferred configuration.
• LARGE front, center, surround
speakers, no subwoofer. The normal
bass from the front, center, and surround
channels is played in its respective speak-
ers. With no subwoofer, the LFE bass is re-
directed to all five LARGE speakers. This
places significant demands on these speak-
ers and their amplifiers, as they must play
their own normal bass plus the very demand-
ing LFE bass.
CENTER BACK SPEAKER(S) (large1/
large2/small1/small2/none): Some
systems have one or two additional center back
surround speakers. Select the LARGE settings
(not available with SMALL front speakers) to
have your center back speaker(s) play low bass.
Use LARGE 1 if you have one center back
speaker (6.1) or LARGE 2 (7.1) if you have
two center back speakers (7.1). If your cen-
ter back speakers have limited bass capabil-
ity or if you would prefer that the bass go to
a subwoofer, use the SMALL setting (SMALL1
for one speaker, SMALL2 for two speakers).
If your system has no center back speakers,
select the NONE setting. With center back
speakers, the Rotel XS eXtra surround, Dolby
Digital EX, DTS-ES, Dolby Pro Logic II, DTS
Neo:6 or other decoders will provide center
back signals for any surround mode.
• All SMALL speakers and subwoofer.
The normal bass from all channels is redi-
rected to the subwoofer, which also plays
the LFE channel. The subwoofer handles
ALL of the bass in the system. This configu-
ration provides several benefits: deep bass
is played by the speaker most suited to do
so, the main speakers may play louder with
less distortion, and the need for amplifier
power is reduced. This configuration should
be used with bookshelf-size or smaller main
speakers. It should also be considered in
some cases with floorstanding front speak-
ers. This configuration is advantageous
when driving the system with moderate
power amplifiers.
Speaker Setup
SPEAKER SETUP
FRONT:Large
CENTER:Large
SURROUND:Large
CENTER BACK:Large1
SUBWOOFER:Yes
ADVANCED:Enter
MAIN MENU
The SPEAKER SETUP menu is used to config-
ure the RSP-1098 for use with your specific
loudspeakers and to determine the bass man-
agement configuration as described in the
previous overview. The menu is accessed from
the MAIN menu.
SUBWOOFER (yes/no/max): The YES set-
ting is the standard setting if your system has
a subwoofer. If your system does not have a
subwoofer, select NO. Select the MAX setting
for maximum bass output with normal bass
being duplicated by both the subwoofer and
any LARGE speakers in the system.
• LARGE front speakers, SMALL cen-
ter and surround speakers, and a
subwoofer. The normal bass from the
SMALL center and surround speakers is re-
directed to the LARGE front speakers and
the subwoofer. The LARGE front speakers
play their own normal bass plus the redi-
rected bass from the SMALL speakers and
LFE bass. The subwoofer plays the LFE bass
plus the redirected bass from all of the other
channels. This might be an appropriate con-
figuration with a pair of very capable front
speakers driven by a large power ampli-
fier. A potential disadvantage with mixed
The following speaker options are available:
FRONT SPEAKERS (small/large): Use the
LARGE setting to have the front speakers play
low bass (full-range). Use the SMALL setting
to redirect normal bass away from these speak-
ers to a subwoofer (high-pass filtered).
ADVANCED: Speaker configuration is gener-
ally a global setting for all surround modes
and need only be done once. However, for
special circumstances, the RSP-1098 provides
the option of setting the speaker configuration
independently for each of four surround modes.
Select the ADVANCED line on the menu and
press ENTER to go to the ADVANCED SPEAKER
SETUP menu described in the following sec-
tion.
CENTER SPEAKER(S) (large/small/
none): Use the LARGE position (not available
with SMALL front speakers) to have the cen-
ter speaker play low bass (full-range). Use the
SMALL position if your center channel speaker
has limited low frequency capability, or if you
prefer that the bass be sent to the subwoofer
(high-pass). Select the NONE setting if your
system does not have a center channel speaker
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
34
To change a setting on the SPEAKER SETUP
menu, place the highlight on the desired line
using the UP/DOWN buttons and use the +/
– buttons to toggle through the available set-
tings. To return to the MAIN menu, press the
ENTER button. Press the MENU/OSD button
on the remote to cancel the display and re-
turn to normal operation.
cess the ADVANCED SPEAKER SETUP menu,
the current master crossover point will be shown
on this line. Change the value of this line only
if you want the current speaker to have a dif-
ferent crossover point. For example, if your
master crossover is set to 80Hz, but you want
your front speakers to crossover to the sub-
woofer at 60 Hz, you would select 60Hz for
the front speakers on this line. This setting ONLY
affects redirected bass and does not affect the
LFE channel in any way. The OFF setting (avail-
able only for the subwoofer) sends a full-range
signal to your subwoofer so that you can use
its built-in low-pass filter.
Subwoofer Setup
SUBWOOFER SETUP
CROSSOVER:100hZ
DOLBY DIGITAL: 0dB
DOLBY PL II: 0dB
DTS: 0dB
STEREO/MPEG:+ 2dB
MUSIC: Off
MULTI INPUT:- 2dB
MAIN MENU
Advance Speaker Setup
The SUBWOOFER SETUP menu allows selec-
tion of the master subwoofer crossover fre-
quency and independent adjustment of sub-
woofer level for each surround mode.
ADV SPEAKER SETUP
SPEAKER:Front
CROSSOVER:100Hz
DOLBY:Small
DTS:Small
STEREO/MPEG:Large
MUSIC:Small
NOTE: When a speaker is set to LARGE on
the SPEAKER SETUP menu or on this MENU,
the crossover setting is not available since,
by definition, a LARGE speaker plays full-
range with no bass redirection to the sub-
woofer and no crossover. Likewise, the OFF
setting for the subwoofer crossover is not avail-
able for SMALL speakers, since SMALL means
that the speaker will redirect its bass below a
given crossover point to the subwoofer. In
addition, the CROSSOVER setting is not avail-
able for the MULTI INPUT.
CROSSOVER (40Hz/60Hz/80Hz/
100Hz/120Hz/150Hz/200Hz/OFF):
This setting specifies a master low-pass filter
for the subwoofer and a corresponding high-
pass filter for all SMALL speakers in the sys-
tem at the selected frequency. To adjust the
crossover frequency, highlight the CROSSOVER
line using the UP/DOWN buttons. Then, use
the +/– buttons to chose the master crossover
point. The 80Hz or 100Hz crossover points
are the most common in home theater systems
and should be used unless you have a spe-
cific reason to choose a different crossover
point based on your specific speakers.
SPEAKER SETUP MENU
In most cases, the standard speaker configu-
ration described above is a global setting and
can be used for all surround modes. However,
the RSP-1098 provides the capability to cus-
tomize these settings for four different surround
modes: Dolby, DTS, Stereo, and Music. For
example, you could set up the Dolby and DTS
modes for 5.1 channel sound, while the Ste-
reo mode changes to a 2-speaker setup with
or without a subwoofer. In addition, the AD-
VANCED SPEAKER SETUP allows you to se-
lect a customized high-pass crossover frequency
for the front, center, surround, and surround
back speakers.
DOLBY (large/small/none): Sets the
current speaker (shown in the first line) to
LARGE, SMALL, or NONE, overriding the
master setting from the SPEAKER SETUP menu.
This setting will ONLY take effect with Dolby
Digital or Dolby Pro Logic II decoding.
The OFF setting sends a full-range signal to
your subwoofer so that you can use its built-
in low-pass filter. With the OFF setting, a 100
Hz high-pass filter is activated for all SMALL
speakers in the system.
DTS (large/small/none): The same op-
tions described for Dolby above, except these
settings ONLY take effect with DTS and DTS
Neo:6 decoding.
NOTE: In most systems, the default settings on
this menu will provide the most predictable
results and most users will not need to change
any settings. You should fully understand bass
management and have a specific reason for
needing a custom configuration before chang-
ing these settings. Otherwise, skip to the fol-
lowing topic, SUBWOOFER SETUP.
NOTE: The master crossover point can be over-
ridden with a custom crossover frequency for
the front, center, surround, or surround back
speakers in theADVANCED SPEAKER SETUP
menu; however, in most systems the single
master crossover point should work well
STEREO/MPEG (large/small/none): The
same options described for Dolby above,
except these settings ONLY take effect in STE-
REO surround mode.
DOLBY DIGITAL:
The available settings on the ADVANCED
SPEAKER SETUP menu are as follows:
MUSIC (large/small/none): The same op-
tions described for Dolby above, except these
settings ONLY take effect with any of the DSP
MUSIC surround modes.
DOLBY PLII:
DTS:
STEREO/MPEG:
MUSIC:
SPEAKER (front/center/surround/cen-
ter back/subwoofer): Select the set of
speakers to be configured with custom settings.
MULTI INPUT:
NOTE: When the front speakers are set to use
the master crossover frequency on the AD-
VANCED SPEAKER SETUPmenu, the surround
mode specific “large/small/none” settings
are not available for the other speakers. These
speakers will use the setting determined in
the basic SPEAKER SETUP menu.
These six lines allow you override the master
subwoofer level setting as determined on the
TEST TONE menu (see below) for each spe-
cific surround mode. When going to the SUB-
WOOFER SETUP menu from the MAIN menu,
the current surround mode is automatically
highlighted. Use the +/– buttons to adjust the
subwoofer level for the current surround mode.
The options are OFF (which turns off the sub-
CROSSOVER (40Hz/60Hz/80Hz/
100Hz/120Hz/150Hz/200Hz): Typi-
cally, the RSP-1098 uses a single master set-
ting for the high-pass and low-pass crossover
point between all SMALL speakers and the
subwoofer. This master crossover point is set
on the SUBWOOFER SETUP menu described
in the following section. When you first ac-
Download from Www.Somanuals.com. All Manuals Search And Download.
English
35
woofer for that mode) and a range of adjust-
ments from –9dB to +9dB and MAX (+10dB).
A setting of 0dB means that the specified sur-
round mode will use the master subwoofer level.
Any other setting is an offset to the master
setting. For example, an adjustment of -2db
for a particular surround mode means that the
subwoofer level will be 2 dB quieter than the
master subwoofer level when that surround
mode is selected. Use these subwoofer level
settings to adjust the relative bass output of
various surround modes. Changing the mas-
ter subwoofer level will increase or decrease
the level for all surround modes.
Test Tone
Calibration with an SPL meter:
Calibrating the system with an SPL meter, rather
than by ear, provides more precise results and
improves the system’s performance significantly.
Inexpensive SPL meters are widely available
and the procedure is quick and easy.
TEST TONE
LEFT:+ 1dB
CENTER:- 1dB
RIGHT:+ 2dB
R SURROUND:+ 5dB
R CTR BACK:+ 2dB
L CTR BACK:+ 2dB
L SURROUND:+ 4dB
SUBWOOFER:+ 9dB
Both Dolby and DTS specify a standard cali-
bration level for all theaters to ensure that
soundtracks can be played at the volume level
intended by the director of the film. This ref-
erence level should result in spoken dialog
played at a realistic level for normal speech
with the loudest peaks in any single channel
at about 105 dB. The RSP-1098’s test tones
are generated at a precise level (-30dBFs)
relative to the loudest possible digitally recorded
sound. At the Dolby or DTS reference level,
these test tones should produce a 75dB read-
ing on an SPL meter.
MAIN MENU
This menu uses filtered pink noise test tones
to set equal volume levels for all speakers (left
front, center, right front, right surround, cen-
ter back, left surround, and subwoofer) to en-
sure proper surround sound reproduction.
Setting the output levels using the test proce-
dure provides the most accurate adjustment
so that digital surround sound material will be
reproduced as it was intended and is a criti-
cal step in calibrating the system.
NOTE: Only the current surround mode can
be adjusted on this menu. You will need to
change surround modes using the front panel
or remote buttons to adjust a different mode.
We recommend starting with the settings for
all surround modes at the default 0 dB setting
during the test tone calibration of the system
and for a period of familiarization after that.
As you listen to a variety of source material
over time, you may notice that certain surround
modes consistently produce too much or too
little bass from the subwoofer. If so, then use
these menu settings to customize each surround
mode. In general, if the master subwoofer level
is set properly (i.e. not too loud), individual
settings for each surround mode should not
be necessary.
Set the meter to its 70dB dial setting with SLOW
response and C-weighting, held away from
your body at your listening position (mount-
ing the SPL meter on a camera tripod makes
this easier). You can point the SPL meter at each
speaker as it is being measured; however,
positioning the meter in a fixed position pointing
at the ceiling is easier and probably produces
more consistent results.
NOTE: If you have configured your system to
use two center back speakers, there will be
an additional line in the menu, giving you the
ability to independently adjust the CENTER
BACK 1 and CENTER BACK 2 speakers.
To access this menu and perform the test tone
calibration, you can be in any surround mode
except BYPASS with any input except the MULTI
INPUT. Enter the OSD menu system and select
TEST TONE from the MAIN MENU to reach
this screen.
Increase the master volume control on the
RSP-1098 until the meter reads 75dB (+5dB
on the meter scale) when playing the test tone
through one of the front speakers. Then, use
the individual channel adjustments on the TEST
TONE menu to adjust each of the individual
speakers, including the subwoofer, to the same
75dB on the SPL meter.
NOTE: In Dolby Digital and DTS recordings,
the LFE channel is used to produce spectacu-
lar low bass effects, placing considerable de-
mands on your subwoofer system. If you hear
distortion or other signs of distress from your
subwoofer at loud listening levels, you may
consider reducing the subwoofer level for the
Dolby Digital and/or DTS surround modes.
In other surround modes, there is no LFE chan-
nel and the subwoofer will only reproduce
redirected bass from the other channels,
which is not as likely to tax the subwoofer.
When you enter the TEST TONE menu, you
will hear a test tone coming from the highlighted
speaker. Highlight different speakers by moving
the cursor to the desired line using the UP/
DOWN buttons. The test tone will shift accord-
ingly to the selected speaker.
NOTE: Due to meter weighting curves and
room effects, the actual level of the subwoofer
may be slightly higher than you measure. To
compensate, Dolby suggests setting the sub-
woofer several dB lower when calibrating
with an SPL meter (i.e. set the subwoofer to
read 72 dB on the meter instead of 75 dB).
Avoid setting the subwoofer level too high
(above 75dB). Exaggerated bass effects come
at the expense of proper blending with the
main speakers and place tremendous stress
on the subwoofer and its amplifier. If you can
localize bass from the subwoofer, the sub-
woofer level is almost certainly too high. Music
can be useful for fine-tuning the subwoofer
level as excessive bass is readily apparent.
The proper setting will generally work well
for music and movie soundtracks.
Seated in the normal listening location, shift
the test tone to the various speakers. Using the
one speaker as a reference, listen for any speak-
ers that are noticeably louder or quieter. If so,
adjust that speaker’s levels up or down (in 1dB
increments) using the +/– buttons. Continue
switching among the speakers and adjusting
until all speakers are the same volume.
To return to the MAIN menu, press the EN-
TER button. Press the MENU/OSD button on
the remote to cancel the display and return
to normal operation.
To return to the MAIN menu, press the EN-
TER button. Press the MENU/OSD button on
the remote to cancel the menu display and
return to normal operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
36
Remember the setting of the master volume con-
trol used during this calibration. To play a Dolby
Digital or DTS soundtrack at the reference vol-
ume level, simply return to that volume setting.
Note that most home theater listeners find this
setting to be excessively loud. Let your own
ears be the judge for deciding how loud to
playback movie soundtracks and adjust the
master volume control accordingly. Regard-
less of your listening levels, using an SPL meter
to calibrate equal levels for all speakers in the
system is strongly recommended.
Contour Setup
Miscellaneous Settings
CONTOUR SETUP
Other Options
SPEAKER:Front
DEFEAT:On
OTHER OPTIONS
HF CONTOUR:+5
LF CONTOUR: 0
RECORD:Source
TURN ON VOL:Last
MAX VOL:Max
VOL SPEED:Slow
POWER:Direct
LANGUAGE:English
VIDEO:NTSC
MAIN MENU
MAIN MENU
The CONTOUR SETUP menu allows digital
adjustment of the bass and treble response of
each group of speakers in the system. For
example, if your center channel speaker sounds
too bright, you could roll off the extreme high
frequencies.
Delay Setup
This OTHER OPTIONS menu, accessed from
the MAIN menu, provides access to a several
miscellaneous settings as follows:
DELAY SETUP
LEFT: 12ft 3.6m
CENTER: 11ft 3.3m
RIGHT: 11ft 3.3m
SPEAKER (front/center/surround/cen-
ter back/all): Select which speaker or group
of speakers to adjust. Selecting ALL permits
adjustment of the entire system as a whole.
RECORD: Select which source signal to be
sent to the recording outputs by choosing one
of the input sources. The options are: CD, TAPE,
TUNER, VIDEO 1–5, and SOURCE. You can
either select a specific component or select
SOURCE which will send the signal to the
record outputs from whatever source is selected
for listening.
R SURROUND: 6ft 1.8m
R CTR BACK: 8ft 2.4m
L CTR BACK: 9ft 2.7m
L SURROUND: 5ft 1.5m
SUBWOOFER: 5ft 1.5m
MAIN MENU
DEFEAT (on/off): Selecting the ON setting
defeats the contour adjustment, bypassing the
contour processing entirely for that speaker
or group of speakers.
The DELAY SETUP menu, which is reached from
the MAIN menu, allows you to set the delay
for individual speakers. This ensures that the
sound from each speaker arrives simultaneously
at the listening position, even when the speakers
are not all placed at equal distances from the
listener. Increase the delay to speakers located
closer to the seating area and decrease the
delay to speakers located farther from the
seating area.
TURN ON VOL: Specifies a default volume
level to be used each time the RSP-1098 is
activated. You can select LAST to have the
RSP-1098 power up with the last previously
used volume setting. Or, you specify a volume
from MIN (full mute) to MAX, in 1 dB incre-
ments. Note that this setting cannot exceed
the MAX VOL established in the next line of
the menu.
HF CONTOUR: Adjusts the extreme high fre-
quency slope over a range of -6dB (MIN) to
+6dB (MAX). Negative number settings reduce
the high frequency output; positive number
settings increase it.
LF CONTOUR: Adjusts the extreme low fre-
quency slope over a range of -6dB (MIN) to
+6dB (MAX). Negative number settings reduce
the low frequency output; positive number
settings increase it.
The RSP-1098 makes setting the delay time
for each speaker very easy. Simply measure
the distance (in feet or meters) from your seating
position to each speaker in your system. Set
the measured distance in the line for each
speaker. The menu provides a line for each
speaker configured in your system and pro-
vides a range of settings up to 99 feet (30
meters) in 1 foot (0.3 m) increments with each
increment equivalent to an additional delay
of 1ms.
MAX VOL: Specifies a maximum volume level
for the RSP-1098. The volume cannot be ad-
justed above this level. Settings range from MIN
to MAX, in 1dB increments.
The contour adjustments are designed to work
at the frequency extremes and be relatively
subtle so that they do not have a negative impact
on midrange sounds. We recommend accli-
mating to the sound of the system with the
contour adjustments defeated and then mak-
ing adjustments, if necessary, to address spe-
cific speaker response issues or personal taste.
VOL SPEED: Provides three options for how
rapidly the volume control responds to inputs.
The SLOW setting adjusts the volume 1dB with
each control input. The MID setting adjusts in
2dB increments. The FAST setting adjusts in
3dB increments.
To change a setting, place the highlight on the
desired line using the UP/DOWN buttons and
use the +/– buttons to increase or decrease
the delay setting. To return to the MAIN menu,
press the ENTER button. Press the MENU/OSD
button on the remote to cancel the display and
return to normal operation.
NOTE: You can also make permanent contour
adjustments using the TONE and UP/DOWN
buttons on the remote. These adjustments are
global, changing the contour settings for all
speakers in the system, regardless of the set-
tings on this menu. See the Contour/Tone
Settings section of this manual for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
37
POWER: This setting determines how the
RSP-1098 powers up. With the default DIRECT
setting, the unit is fully activated when AC power
is applied and the rear panel POWER button
is ON; however, it may be put in standby mode
using the front panel STANDBY button or the
remote ON/OFF buttons. This would be the
normal setting for most systems.
Zone 2 Setup
MAX VOL: Specifies a maximum volume level
for Zone 2. The volume cannot be adjusted
above this level. Settings range from MIN to
MAX, in 1dB increments.
ZONE2 SETUP
SOURCE:Off
VOLUME SETUP:Variable
VOLUME:60
TURN ON VOL:Last
MAX VOL:Max
12V TRIGGER:Off
12V TRIGGER: The RSP-1098 has four 12V
trigger outputs that supply a 12V DC signal
to turn on Rotel components and other com-
ponents as needed. The 12V Trigger labeled
ZONE2 is assigned to Zone 2 and can send
a turn-on signal to remote components when-
ever Zone 2 is activated. Select the ON set-
ting to have the ZONE2 trigger output send
the turn-on signal. Select the OFF setting to dis-
able the 12V trigger function for Zone 2.
MAIN MENU
With the STANDBY setting, the unit powers
up in standby mode when AC is applied and
the rear panel POWER button is ON. The unit
must be activated using the front panel
STANDBY button or the remote ON/OFF
buttons.
The ZONE 2 SETUP menu provides settings
and configuration options related to the op-
eration of Zone 2. This menu is reached by
highlighting the ZONE 2 line on the MAIN
menu and pressing ENTER.
In ALWAYS-ON mode, the unit remains fully
active whenever AC is present and the rear
panel POWER button is ON; the front panel
STANDBY button and the remote ON/OFF
buttons are disabled and the unit cannot be
put in standby mode.
Default Setup
SOURCE: Specifies a source for listening in
Zone 2. Options are CD, TUNER, TAPE, VIDEO
1–5, SOURCE, and OFF. Selecting the
SOURCE option links the Zone 2 source to the
source selected for the main zone so that Zone
2 will hear the same source as the main zone.
Selecting the OFF option turns Zone 2 off.
DEFAULT SETUP
FACTORY DEFAULT:No
USER DEFAULT:No
SET USER DEFAULT:No
LANGUAGE: Selects a language for the
OSD/TFT displays.
MAIN MENU
VOLUME SETUP: configures the Zone 2
outputs for VARIABLE or FIXED volume levels.
VARIABLE allows control of the volume settings
in Zone 2 from the RSP-1098 front panel or
from a remote control/IR repeater in Zone 2.
FIXED output disables the Zone 2 volume
control. In this mode, the Zone 2 level can be
fixed at the level specified on the next line,
thus optimizing system performance when send-
ing a fixed level signal to a preamp or ampli-
fier with its own volume adjustment.
VIDEO: Specifies whether an NTSC or PAL
television monitor is connected to the TV
MONITOR outputs of the RSP-1098. This set-
ting must be correct for the upconversion and
OSD menus to work properly.
The DEFAULT SETUP menu provides access to
three functions:
• Restore all features and settings to the origi-
nal FACTORY DEFAULT settings.
Change settings on the OTHER OPTIONS menu
by highlighting the desired line using the UP/
DOWN buttons and using the +/– buttons to
step through the available settings. To return
to the MAIN menu, press the ENTER button.
Press the MENU/OSD button on the remote
to cancel the display and return to normal
operation.
• Memorize a custom group of settings as
a USER DEFAULT.
• Activate the memorized USER DEFAULT set-
tings.
VOLUME: In VARIABLE output mode, this line
shows the current volume setting for Zone 2.
In FIXED output mode, this volume setting es-
tablishes a permanent fixed output level for
Zone 2.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to YES. Press the ENTER button to proceed with
resetting the FACTORY DEFAULT settings. The
unit will power off and then on, with the fac-
tory settings restored. To return to the MAIN
menu without resetting the FACTORY DEFAULT
settings, change the entry to NO and press
the ENTER button.
Move the highlight to the desired line using
the UP/DOWN buttons and use the +/– but-
tons to adjust the volume level. To return to the
MAIN menu, press the ENTER button. Press
the MENU/OSD button on the remote to cancel
the display and return to normal operation.
TURN ON VOL: Specifies a default volume
level to be used each time Zone 2 is activated.
You can select LAST to have Zone 2 activate
with the last previously used volume setting.
Or, you specify a volume from MIN (full mute)
to MAX, in 1 dB increments. Note that this
setting cannot exceed the MAX VOL established
in the next line of the menu.
NOTE: Resetting to factory default settings will
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will loseALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
Download from Www.Somanuals.com. All Manuals Search And Download.
RSP-1098 Surround Sound Processor
38
To memorize USER DEFAULT settings:
Many of the current configuration settings can
be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.
To save the current settings as a USER DEFAULT,
place the highlight on the SET USER DEFAULT
line using the UP/DOWN buttons and use the
+/– buttons to change the setting to YES. Press
the ENTER button to store the new USER DE-
FAULT settings. To return to the MAIN menu
without saving any changes, change all en-
tries on the screen to NO and press the EN-
TER button.
No video output on TV monitor.
MORE INFORMATION
• Make sure that the TV monitor is connected
properly. Component video outputs can
send any type of signal to the TV. Com-
posite video connections can only send
video from composite sources and S-Video
connections can only send video from
S-Video sources.
Troubleshooting
The unit does not turn on.
• Make sure the power cord is plugged into
the rear panel and a live AC wall outlet.
• Make sure the NTSC/PAL switch is set
properly.
• Make sure the rear panel POWER switch
is in the ON position
No video or distorted video on TFT
screen.
No sound from any input.
NOTE: If there is insufficient memory to store a
USER DEFAULT configuration file, the SET
USER DEFAULT option will not be available.
• Make sure that a composite video source
is selected for display on the TFT screen.
The TFT screen cannot display S-Video or
Component Video signals.
• Make sure that MUTING is off and VOL-
UME is turned up. If the TFT screen and
the TV monitor are turned off, the MUTING
can be on with no visual indication.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT configuration file, you can activate those
settings at any time by placing the highlight
on the USER DEFAULT line using the UP/
DOWN buttons. Use the +/– buttons to change
the setting to YES. Press the ENTER button to
proceed with activating the USER DEFAULT
settings. To return to the MAIN menu without
activating the USER DEFAULT settings, change
the entry to NO and press the ENTER button.
• When progressive scan video from a DVD
player is being received at the Component
Video inputs, the composite video signal
from the DVD player may be corrupted.
• Make sure that preamp outputs are con-
nected to a power amplifier and that the
amplifier is turned on.
• Make sure source inputs are connected and
configured correctly.
OSD menus are not displayed on TV
Monitor or TFT screen.
No sound from digital sources.
• Go to Setup menus and configure OSD
menus to be displayed on the TV monitor
and/or the TFT screen.
• Make sure that digital input connector is
assigned to the proper source input and
that the source input is configured to use
the digital input rather than an analog input.
• In some PAL systems, the menus may not
be displayed unless there is an active video
signal. Use the TFT screen for menu opera-
tion.
• Check the configuration of the DVD player
to ensure that the bitstream and/or DTS
digital output is activated.
• When using progressive scan video sig-
nals, make sure that the progressive mode
is set to YES in the Display Options setup
menu. This allows the display of the main
setup OSD menus on the TV monitor by
interrupting the progressive scan video
signal and restoring it after the OSD menus
are cancelled. The temporary information
screens (such as volume, etc.) cannot be
displayed on the TV monitor when progres-
sive scan signals are being used.
No sound from some speakers.
• Check all power amp and speaker con-
nections.
• Check Speaker Configuration settings in
the Setup menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
39
Video and Audio do not match.
Specifications
• Check that the proper video source is se-
lected for each input.
Audio
• Check that the group delay (lip-synch) setting
is not misadjusted.
Total Harmonic Distortion
<0.05%
Intermodulation Distortion (60 Hz:7 kHz)
<0.05%
Clicking or popping sounds when
switching inputs.
Frequency Response
10 Hz – 120 kHz, 3 dB (analog bypass)
10 Hz – 95 kHz, 3 dB (digital input)
• The unit uses relay switching to preserve
maximum sound quality. The mechanical
clicking of the relays is normal.
Signal to Noise Ratio (IHF A-weighted)
95 dB (analog bypass)
92 dB (Dolby Digital, dts) 0dBFs
• During switching, it may take a split sec-
ond for digital signals to be recognized
and properly decoded. Rapid repeated
switching between inputs or settings can
result in clicks or pops from the speakers
as the unit attempts to lock on to the rap-
idly changing signals. This causes no harm.
Input Sensitivity/Impedance
Line Level: 200 mV/100K ohms
Preamp Output Level/Output Impedance
1.0 V / 250 ohms
Contour (LF/HF)
6 dB at 50 Hz/15 kHz
Decodable Digital Input Signals
Dolby Digital, Dolby Digital EX, DTS, DTS-ES,
DTS 96/24, LPCM (up to 192K), HDCD, MP3,
MPEG Multichannel
Controls do not operate.
• Make sure that fresh batteries are installed
in the remote.
Video
Frequency Response
3 Hz – 10 MHz, 3 dB (Composite, S-Video)
3 Hz – 100 MHz, 3 dB (Component Video)
• Make sure that the IR sensor on the front
panel is not blocked. Aim the remote at
the sensor.
note: TFT screen displays Composite Video signals
only.
• Make sure the sensor is not receiving strong
IR light (sunlight, halogen lighting, etc.)
Signal to Noise Ratio
45 dB
• Unplug the unit from the AC outlet, wait
30 seconds, and plug it back in to reset.
Input Impedance
75 ohms
Output Impedance
75 ohms
Output Level
1.0 volt
General
Power Consumption:
70 watts (normal)
60 watts (TFT screen off)
7.5 watts (standby)
Power Requirements (AC)
115 volts, 60Hz (USA version)
230 volts, 50Hz (CE version)
Weight
15.7 Kg/34.6 lb.
Dimensions (W x H x D)
432 x 164 x 435 mm
17.01" x 6.46" x 17.13"
Front Panel Height
(feet removed for rack mount)
150 mm / 5.91"
When sizing openings in custom cabinets, measure
the unit to be installed and/or allow at least 1 mm
clearance on all sides for unit to unit tolerances.
All specifications are accurate at the time of
printing. Rotel reserves the right to make improve-
ments without notice.
Rotel and the Rotel HiFi logo are registered
trademarks of The Rotel Co, Ltd., Tokyo, Japan.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Rotel Co. Ltd.
10-10 Shinsen-Cho
Shibuya-Ku
Tokyo 150-0045
Japan
Phone: +81 3-5458-5325
Fax: +81 3-5458-5310
Rotel of America
54 Concord Street
North Reading, MA 01864-2699
USA
Phone: +1 978-664-3820
Fax: +1 978-664-4109
Rotel Europe
Dale Road
Worthing, West Sussex BN11 2BH
England
Phone: +44 (0)1903 221600
Fax: +44 (0)1903 221525
Rotel Deutschland
Kleine Heide 12
D-33790 Halle/Westf.
Germany
Phone: +49 05201-87170
Fax: +49 05201-73370
www.rotel.com
082 OM-RSP-1098 English 053103
Download from Www.Somanuals.com. All Manuals Search And Download.
|