DAB / FM RDS Stereo Digital Radio with built-in battery charger
Please read this manual before use
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
(Top)
11
10
1
2
3
4
5
6
7
8
1
9
1. Speaker x 2
5. Favourite button
6. Info button
7. Preset button
8. On / Off button
9. Tuning / Select control
10. Charge / Low battery indicator
11. Telescopic aerial
2. Volume control
3. DAB / FM button
4. Auto Tune button
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
2
020 8758 0338 (Mon-Fri)
Controls
(Rear)
12. Headphone socket
13. Auxiliary input socket
14. Battery compartment
15. USB socket (for service use only)
16. DC input socket
17. Battery compartment screw
12
13 14 15
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Battery operation using alkaline batteries
(also see page 23)
1. Ensure your radio is disconnected from the mains supply and the
aerial is fully retracted.
2. Open the battery cover on the base of the unit by using a flat bladed
screwdriver to loosen the screw securing the battery cover.
3. Slide the switch inside the battery compartment to the Alkaline
position.
2
4. Insert four LR20 (D size) Alkaline batteries into the spaces in the
compartment. Take care to ensure all batteries are inserted with the
correct polarity as shown inside the battery compartment.
5. Closethebatterycoverandgentlytightenthescrewusingaflatbladed
screwdriver. Do not overtighten.
•
Important: when usingAlkaline batteries the battery switch must
be placed in the Alkaline position. Failure to do so could result
in serious damage to the batteries or radio.
•
When the batteries are exhausted, the charge/low battery indicator
will show red for a short while. The radio will then switch itself off. It
may not be possible to switch the radio back on until the batteries are
replaced, or until the radio is connected to the mains adaptor.
3
•
•
If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
We would recommend for economy that the Expression is used via
theACadaptorwheneverpossiblewithbatteryoperationforoccasional
use only. If extended listening using batteries is anticipated, then the
use of rechargeable batteries is recommended.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
4
020 8758 0338 (Mon-Fri)
Battery operation using rechargeable batteries
(also see page 23)
1. Ensure your radio is disconnected from the mains supply and the
aerial is fully retracted.
2. Open the battery cover on the base of the unit by using a flat bladed
screwdriver to loosen the screw securing the battery cover.
3. Slide the switch inside the battery compartment to the NiMH
position.
2
4. Insert four Rechargeable LR20 (D size) batteries into the spaces in the
compartment. Take care to ensure all batteries are inserted with the
correct polarity as shown inside the battery compartment. The radio is
designed to be used with Nickel Metal Hydride (NiMH) rechargeable
batteries.
5. Closethebatterycoverandgentlytightenthescrewusingaflatbladed
screwdriver. Do not overtighten.
6. Plug the mains adaptor into your radio and then plug the adaptor into
the mains.
7. The Charge light will flash green indicating that the batteries are
charging.Batterieswillbefullychargedinaround3-7hoursdepending
on their capacity. The charge light shows a steady green light when
the battery charging is complete.
3
•
Important: when using rechargeable batteries the battery switch
must be placed in the NiMH position. Batteries will only be
charged when the radio is switched off and connected to the AC
adaptor.
IMPORTANT: The batteries should not be exposed to excessive heat
such as sunshine, fire or the like. After use, disposable batteries should
if possible be taken to a suitable recycling centre. On no account
should batteries be disposed of by incineration.
•
When the batteries are exhausted, the charge/low battery indicator
light will show red for a short while. The radio will then switch itself off.
It may not be possible to switch the radio back on until the batteries
are recharged, or until the radio is connected to the mains adaptor.
•
If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using the AC adaptor
1. Insert the adaptor plug into the DC in socket on the rear of your
radio.
2. Plug the adaptor into a standard 13A mains socket outlet. Whenever
the adaptor is plugged in to the radio and switched on at the mains the
batteriesareautomaticallydisconnected.Iftheadaptorispluggedinto
the radio but not switched on then the radio will run from the batteries
if fitted.
The AC adaptor should be disconnected from the mains supply and
the radio when not in use.
•
IMPORTANT: The mains adaptor is used as the means of connecting
the radio to the mains supply. The mains socket used
for the radio must remain accessible during normal use. In order
to disconnect the radio from the mains completely, the mains
adaptor should be removed from the mains socket outlet
completely.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
6
020 8758 0338 (Mon-Fri)
Operating your radio - DAB
1. Carefully extend the telescopic aerial.
2. Press the On/Off button to switch on your radio. The display will show
"Welcome to DAB".
2
3. If this is the first time the radio is used a quick scan of the Band III
DAB channels will be carried out. If the radio has been used before
the last used station will be selected.
4. During the scanning process, the lower line of the display shows a
bar-graph indicating progress of the scan.
5. When the scanning is completed the first station (in numeric-alpha
order 0...9...A....Z) will be selected.
6. If the station list is still empty after the scan your radio will display
"Service not available".
7. If no signals are found it may be necessary to relocate your radio to
a position giving better reception. Then, either switch your radio off
and on again, or press the Auto Tune button to repeat the scan.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Selecting a station - DAB
1. The top line of the display shows the name of the station currently
selected.
2. Rotate the Tuning control to scroll through the list of available stations
on the lower line of the display. Stop rotating the Tuning control when
you find the station that you wish to hear.
3. Press and release the Tuning control to select the station. The display
may show "Now tuning..." while your radio finds the new station.
2,3
4. Adjust the Volume control to the required setting.
Note: If after selecting a station the display shows "Service not available"
it may be necessary to relocate your radio to a position giving better
reception.
The use of radio station presets for selecting your preferred radio stations
is described on page 17.
4
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
8
020 8758 0338 (Mon-Fri)
Display modes - DAB
Your radio has a range of display modes:-
1. Press the Info button to cycle through the various modes.
a
b
1
a. Scrolling text
b. Program Type
c. Multiplex Name
Displays scrolling text messages such as
artist/track name, phone in number etc.
Displays the type of station being listened
to e.g. Pop, Classic, News etc.
c
Displays the name of DAB multiplex to
which the current station belongs.
d
e
d. Time and date
e. Frequency
Displays the current time and date.
Displays the frequency of the DAB
multiplex for the station listened to.
f
f. Bit rate & audio type
Displays the digital bit rate & audio type
for the station being listened to.
g
g. Signal Strength
Displays a graph showing the signal
strength for the station being received.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Finding new radio stations - DAB
As time passes new stations may become available. To find new stations
proceed as follows:-
1
1. Press and release the Auto Tune button. The display will show
"Scanning..." and your radio will perform a scan of the Band III DAB
channels. As new radio stations are found the station counter on the
right-hand side of the display will increase and the radio stations will
be added to the list stored in the radio.
Secondary services - DAB
1. Certainradiostationshaveoneormoresecondaryservicesassociated
with them. If a radio station has a secondary service associated with it
the display will show ">>" next to the station name on the station list.
The secondary service will then appear immediately after the primary
service as you rotate the tuning control clockwise.
1,2
2. Press and release the Tuning control to select the station.
3. When the secondary service shuts down, your radio will automatically
switch back to the main radio station (or primary service) if it is
available.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
10
020 8758 0338 (Mon-Fri)
Manual Tuning - DAB
Manual tuning allows you to tune directly to the various DAB Band III
channels. UK DAB stations are currently located in the range 11B to
12D.
1
1. Press and hold in the Info button until the display shows "Manual
tune". Press and release the Tuning control to select this function.
2. Rotate the Tuning control to select the required DAB channel.
3. Press and release the Tuning control. The open block in the signal
strength graph shows you the minimum signal strength needed for
good DAB reception. The signal blocks will go up and down showing
the changing signal strength as you adjust the telescopic aerial or
the radio position. Any new radio stations found on the tuned DAB
multiplex will be added to the list stored in the radio.
1-4
4. Press and release the Tuning control to return to the normal tuning
mode.
Signal strength display - DAB
1. Repeatedly press and release the Info button until the lower line of
1
the display shows signal strength.
2. Position your radio and try adjusting the aerial so as to give maximum
number of black rectangles on signal strength display. Normally, the
best reception will be found with the aerial fully extended.
3. The clear unfilled rectangle indicates minimum signal level required
for satisfactory reception.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Dynamic Range Control settings - DAB
Dynamic Range Control (also known as DRC) can make quieter sounds
easier to hear when your radio is used in a noisy environment.
1
2
1. Press the On/Off button to switch on your radio.
2. Press and hold in the Info button. The display will show “Manual
tune.”
3. Rotate the Tuning control until the display shows "DRC".
4. Press and release the Tuning control to enter the adjustment
mode.
5. Rotate the Tuning control to select the required DRC setting (the
default is 0).
DRC 0 - DRC is switched off, Broadcast DRC will be ignored.
DRC 1/2 - DRC level is set to 1/2 that sent by broadcaster.
DRC 1 - DRC level is used as sent by broadcaster.
3-6
6. Press and release the Tuning control to confirm the setting. The
display will return to normal tuning mode.
Note: Not all DAB broadcasts are able to use the DRC function. If the
broadcast does not support DRC, then the DRC setting in the radio will
have no effect.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
12
020 8758 0338 (Mon-Fri)
Operating your radio - Search tuning - FM
1. Carefully extend the telescopic aerial fully.
2
2. Press the On/Off button to switch on your radio.
3. Press the DAB/FM button to select the FM band.
4. Press and immediately release the Auto tune button, your radio will
scan in an upwards direction (low frequency to high frequency) and
stop automatically when it finds a station of sufficient strength.
3
5. After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RDS data present then the radio will display the station name.
4-7
6. To find other stations, press and release the Auto tune button as
before.
7. To scan the FM band in a downwards direction (high frequency to low
frequency) press and hold down the Auto tune button for 2 seconds
and then release.
8. Whenthewavebandendisreachedyourradiowillrecommencetuning
from the opposite waveband end.
9
9. Adjust the Volume control to the required setting.
If you find that an FM broadcast has a lot of background hiss, this may
often be reduced by setting the radio into Mono reception mode for the
current FM station. Please refer to the section "Stereo / Mono setting - FM"
on page 18 for further details.
The use of radio station presets for selecting your preferred radio stations
is described on page 17.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Manual tuning - FM
1. Press the On/Off button to switch on your radio.
1,6
2. Press the DAB/FM button to select the FM band. Carefully extend the
telescopic aerial fully for FM reception.
3. Rotate the Tuning control to tune to a station. With each click of the
control the frequency will change up or down by 50 kHz.
2
4. When the waveband end is reached the radio will recommence tuning
from the opposite waveband end.
5. Set the Volume control to the desired settings.
6. To switch off your radio press the On/Off button.
If you find that an FM broadcast has a lot of background hiss, this may
often be reduced by setting the radio into Mono reception mode for the
current FM station. Please refer to the section "Stereo / Mono setting - FM"
on page 18 for further details.
3
5
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
14
020 8758 0338 (Mon-Fri)
Display modes - FM
The Radio Data System (RDS) is a system in which inaudible digital
information is transmitted in addition to the normal FM radio programme.
RDS offers several useful features. In FM mode the bottom line of the
display can be set to any of the following display options:-
1
a
b
1. Press the Info button to cycle through each of the options.
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number
etc.
b. Program type
Displays type of station being listened to
e.g. Pop, Classic, News, etc.
c
c. Time and date
d. Frequency
Displays the current time and date.
d
e
Displays frequency of the station being
listened to.
e. Audio mode
Display shows Auto (stereo) or Mono.
Note: Your radio will display "No Radio Text" on the lower line of the
display if there is no scrolling text available and "No PTY" if there is no
programme type information.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Favourite button
Your radio is fitted with a button which when pressed will automatically
select the required waveband and tune to your Favourite radio station.
With this button you can store one favourite station from either the DAB
or FM wavebands.
To set up your favourite station, follow these steps:
1. Carefully extend the telescopic aerial and switch on your radio.
2. Select the desired waveband (DAB or FM) and tune into the required
radio station as described on the preceding pages.
3. Press and hold down the Favourite button (for 5 seconds) until the
3
display shows "My Fav. Saved".
Recalling your favourite station
1. Carefully extend the telescopic aerial and switch on your radio.
If your radio is inAuxiliary Input mode, press and release the DAB/FM
button to select normal radio operation.
2. Momentarily press the Favourite button, your radio will automatically
select the DAB or FM waveband as needed and then tune to the radio
station stored in the favourite memory.
2
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
16
020 8758 0338 (Mon-Fri)
Preset stations - DAB and FM
To make it easier for you to tune your radio to the stations that you prefer,
you may store selected radio stations as presets. Your radio holds presets
separately for DAB and FM radio modes.
You may set as many or as few presets as you like in each mode.
You can easily switch between displaying all DAB stations (or all FM
frequencies) and displaying only those that you have set as presets.
Any station or frequency which has been marked as a preset can easily
have the mark cancelled should your preferences or needs change.
Presets are retained when your radio is switched off.
1. To setup your preset stations, tune into the required station.
2. Press and hold down the Preset button until the displays shows a tick
symbol next to the radio station name or frequency. This indicates that
the radio station is marked as a preset. To cancel the preset mark,
press and hold the Preset button again.
2,4
3. Repeat steps 1 and 2 as needed for any other stations that you want
as presets.
4. To view only the preset stations for the currently selected waveband
when tuning, press and release the Preset button so that the heart
symbol shows in the display.
5
5. To listen to one of the preset radio stations, rotate the Tuning control
until the required radio station is displayed. Press and release the
Tuning control to select and tune to that station.
6
6. Tocancelthepresetstationsview,pressandreleasethePresetbutton
so that the heart symbol disappears from the display. Your radio will
then be able to access the full station list using the Tuning control.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Stereo / Mono setting - FM
Your radio will play stereo FM broadcasts in stereo provided that the
received signal is of adequate strength. However, as a stereo signal
becomes weaker the audio signal will become poorer. It may be preferable
to force the radio to play the station in mono in order to reduce the level
of background hiss.
1. Press the On/Off button to switch on your radio.
1
2. Tune to the required FM radio station as previously described (see
pages 13, 14).
3. PressandreleasetheTuningcontrolsothatthedisplayshows"Switch
to Mono". The radio will play the current station in mono.
TheMonooverrideisatemporarysettingandisappliedtothecurrently
tuned station only. It is cancelled automatically by tuning to another
station.
3-4
4. If you wish to cancel the Mono override while listening to the currently
tuned radio station, press and release the Tuning so that the display
shows "Switch toAuto". The radio will play the current station in stereo
if the signal is sufficiently strong.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
18
020 8758 0338 (Mon-Fri)
Scan sensitivity setting - FM
Your radio will normally scan for FM broadcasts which are strong enough
to give good reception. However, you may wish the Auto-scan function
to also be able to find weaker signals, possibly from more distant radio
transmitters. Your radio includes a local / distant option for the Auto-scan
function.
1
1. Press the On/Off button to switch on your radio.
2
2. If needed, press the DAB/FM button to select the FM band.
3. Press and hold the Info button until the display shows "FM Scan
Zone" then press the Tuning control to enter the scan zone selection
menu.
3
4. RotatetheTuningcontroltoswitchbetweenLocalandDistantoptions
on the lower line of the display. The Distant option will allow the radio
to find weaker signals when scanning.
The currently stored setting will be shown with an asterisk on the
display.
5. Press and release the Tuning control to confirm your selection. The
radio will then revert to the normal information display. The Local or
Distant setting is stored in the radio and remains in force until changed
or until a System Reset.
3-5
Note: The initial setting (out of the box, or after a System Reset) causes
the radio to ignore weaker (or more distant) signals.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Software version
The software display cannot be altered and is just for your reference.
1,3
1. To view the software version on the display, ensure your radio is in
DAB mode and press and hold the Info button for 2 seconds.
2. Rotate the Tuning control until the display shows “SW version”. Press
the Tuning control the software version will appear on the display.
3. Press the Info button to revert to the normal display mode.
2
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
20
020 8758 0338 (Mon-Fri)
System reset
If your radio fails to operate correctly, or some digits on the display are
missing or incomplete, it may be possible to restore normal operation by
carrying out a System Reset operation on your radio. This will restore the
radio's settings to their factory defaults. No presets will be stored, and the
list of DAB radio stations will be empty.
If you have moved to a different part of the country and you wish to erase
local DAB radio stations that are no longer available from the stored list,
thenyoumaycarryoutthisprocedure.Yourradiowillautomaticallyre-scan
for the DAB stations available at your current location when it restarts.
1. Ensure your radio is in DAB or FM mode. Press and hold down the
Info button for 2 seconds.
1
2. Rotate the Tuning control until the display shows "Factory Reset",
then press and release the Tuning control.
3. Ifyouwishtoperformtheresetoperation,pressandreleasetheTuning
control one more time. A full reset of your radio will be performed. All
presets and station lists will be erased.
2-3
4. After a system reset a scan of the DAB band will be performed.
In case of malfunction due to electrostatic discharge, reset the product
(temporary disconnection of the power adaptor and removal of batteries
may be required) to resume normal operation.
If a problem persists our technical staff would be pleased to offer
anyassistanceonoperatingtheradio. Ourtechnicalhelplinenumber
is 020 8758 0338.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Headphone socket
A3.5mm Headphone Socket located on the rear of your radio is provided
forusewitheitherheadphonesoranearpiece.Insertingaplugautomatically
mutes the internal loudspeaker.
Please be aware that sensitivity of headphones can vary widely. We
therefore recommend setting volume to a low level before connecting
headphones in the radio.
IMPORTANT:Excessivesoundpressurefromearphonesandheadphones
can cause hearing loss.
Auxiliary input socket
1. Connect a stereo or mono audio source (i.e. CD player, MP3 player,
etc.) to the Auxiliary input socket.
2. Press the On/Off button to switch on the radio. Press and release the
DAB/FM button until the display shows "AUX IN".
Note that the Auxiliary Input mode can only be selected when a
plug is inserted in the socket.
3. Adjust the Volume control on your player and on the radio for
comfortable listening.
4. Remove the cable from the Auxiliary input socket or press and
release the DAB/FM button to cancel Auxiliary Input mode.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
22
020 8758 0338 (Mon-Fri)
A Few Words about Batteries…
Rechargeable batteries
Your Roberts Expression radio has been designed to use a choice of
power sources. You may plug it into the mains using the supplied high-
efficiency adaptor, or for listening away from the mains you may use
either alkaline or rechargeable batteries. We do not recommend the use
of carbon-zinc or zinc-chloride batteries.
Your Expression radio uses a range of methods to ensure correct and
safe charging of Rechargeable Nickel-Metal-Hydride batteries. These
work to protect your batteries from excessive charge and discharge.
These protections can only work properly if the advice above is followed.
In particular, the radio will not be able to correctly charge batteries if
they are a mixture of different brands, or different ages, or different
capacities.
It is very important that you read the advice and warnings given
below.
We recommend that all the rechargeable batteries used in your radio
are bought together as a set. They should always be charged together
and discharged together and not “borrowed” from time to time for other
applications. This will ensure that they give their optimum performance
in your radio.
1) Whichever type of batteries you choose to use, it is very important
that the battery selection switch under the cover is set to the correct
type.
a. If no batteries are fitted, then set the switch to the Alkaline position.
This position minimises the power consumption when the radio is
powered from the mains.
b. If Alkaline batteries are fitted, then set the switch to the Alkaline
position.
c. If Rechargeable batteries are fitted, then set the switch to the
NiMH position. Your radio is designed to use Nickel-Metal-Hydride
rechargeable batteries. No other type of rechargeable battery should
be used in the radio.
We recommend that the rechargeable batteries that you use should
be from a quality brand, and should be of at least 2500mAh capacity.
Batteries of this capacity should power your radio for between 10 and
15 hours depending upon the volume of the radio, whether DAB or FM
mode is used (DAB mode uses slightly less power than FM), and also
depending on the condition of the batteries. Higher capacity batteries are
available and will give longer life, but will generally be more expensive.
2) NEVER mix old and new Alkaline batteries. The old batteries may
suffer damage and leak which will damage your radio and whatever
the radio is standing on.
Before you first install a new set of rechargeable batteries into your
radio you should first make sure that the battery type switch beneath the
battery cover is in the NiMH position. Install the batteries arranging them
as shown inside the battery compartment. Plug the mains adaptor into the
radio and then into the mains socket. While the batteries are charging the
charge indicator should show a flashing green light. When the batteries
are fully charged the indicator will stop flashing and will show a steady
green light. The time taken to charge the batteries will depend on how
much charging they require. New batteries may be partly charged when
first fitted, but it is normal for a set of batteries to take several hours to
charge fully (this can be between 3 and 7 hours depending on the battery
capacity and their initial state of charge).
3) NEVER mix old and new Rechargeable batteries. This may
result in unreliable charging and shortened battery life. Never mix
Rechargeable batteries of different types or capacities even if they
are new.
4) NEVER mix Alkaline and Rechargeable batteries. The recharging of
Alkaline batteries can be very dangerous.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
If you use the radio powered from the batteries, the charge/low battery
indicator light will be off until the batteries are exhausted. The charge/
low battery indicator light will then show red for a short while before the
radio switches itself off. It does this in order that the batteries are not
excessively discharged. This would otherwise damage the batteries and
shorten their life.
To avoid danger and risk of injury, please follow
these guide lines
Improper use of batteries may result in leakage of fluid, overheating
or explosion. Battery fluid is corrosive and may also be toxic. Battery
fluid can cause skin burns, can damage the eyes, and can be harmful if
swallowed.
If you use the radio powered from the mains with rechargeable batteries
fitted, the charging process is suspended until you switch off the radio.
When you switch off the radio using its On/Off button charging will
then resume. If the batteries have already been charged then they will
only charge for a few more minutes before the charge indicator stops
flashing.
1. Keep batteries out of the reach of children.
2. Do not heat, open, puncture, mutilate or dispose of batteries by
burning.
3. Do not mix different battery types or old and new batteries. Always
replace all the batteries at the same time.
If you only listen to your radio for short periods, you do not need to
connect your radio to the mains to charge the batteries every time that
you use it. However, if the radio is not to be used for a few weeks, then
we recommend that the batteries are fully charged (charge light shows
steady green) before the radio is put to one side.
4. Do not carry or store batteries such that metal objects may contact
the end caps.
5. Remove batteries from the radio if they are worn out or if you are
storing it for a long time.
6. Remove old or worn out batteries promptly, and recycle or dispose of
them according to the regulations applicable to your location.
7. If a battery does leak, remove all batteries from the product, taking
care to avoid directly touching the leaked fluid. If the fluid contacts
skin or clothes wash with water immediately. Before inserting new
batteries, thoroughly clean the battery compartment with a damp
paper towel, or follow the battery manufacturer’s advice for clean
up.
If you intend not to use your radio for some months, then we recommend
that the batteries are removed and put away, keeping them in a cool
place out of reach of children, away from moisture and such that no metal
object can contact the battery terminals.
With care, rechargeable batteries can last a long time and can operate for
many hundreds of charge and discharge cycles. When your rechargeable
batteries can no longer power your radio adequately, please dispose of
them responsibly using a local battery recycling facility.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Display backlight
1. When using the radio powered from batteries, the display backlight
will be switched on for approximately 12 seconds when any button is
pressed.
2. When your radio is powered by theAC mains using the supplied mains
adaptor the display backlight will always be on whenever the radio is
switched on.
USB socket for software upgrade
A USB socket is provided at the rear of your radio for service use only to
permit the possibility of updates to the internal software in the future.
include a valid e-mail address you will receive notification of software
updates.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
•
•
•
Your radio should not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
radio.
It is recommended to operate the product such that there is a minimum
distance (10cm recommended) to adjacent objects in order to ensure
good ventilation.
The ventilation of the product should not be restricted by covering it or
its ventilation openings with items such as newspapers, tablecloths,
curtains etc.
No naked flame sources such as lighted candles should be placed on
the product.
General
Do not allow this radio to be exposed to water, steam or sand. Do not leave
your radio where excessive heat could cause damage such as in a parked
car where the heat from the sun can build up even though the outside
temperature may not seem too high. It is recommended that the DAB band
beusedwhereverpossibleasbetterresultsintermsofqualityandfreedom
from interference will usually be obtained than on the FM band.
The name plate is located on the underside of your radio.
•
•
It is recommended to avoid using or storing the product at extremes
of temperature.Avoid leaving the unit in cars, on window sills, in direct
sunlight etc.
Specifications
Circuit Features
Loudspeaker
Power Requirements
2 x 76mm
2 x 1 watt
Mains
AC 100
240V 50/60Hz (adaptor)
Batteries
Battery Life
4 x LR20 (D size)
Output Power
Up to 100 hours of listening for 4 hours a day
at normal volume using alkaline cells.
Up to 15 hours - 2500 mAh NiMH
Up to 40 hours - 9000 mAh NiMH
Headphone socket
Auxiliary Input socket
3.5mm dia. stereo
3.5mm dia. stereo
Aerial System
FM
DAB
Telescopic aerial
Telescopic aerial
Frequency Coverage
FM
DAB
87.5-108MHz
174.928 - 239.200MHz
The Company reserves the right to amend the specification without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Guarantee
This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component
breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free
of charge.
The guarantee does not cover:
1. Damage resulting from incorrect use.
2. Consequential damage.
3. Receivers with removed or defaced serial numbers.
N.B. Damaged or broken telescopic aerials will not be replaced under guarantee.
Procedure:
Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer
will be able to attend to any defect quickly and efficiently, but should it be necessary the dealer will return the instrument to the company’s service
department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact
Roberts Radio Technical Services at the address shown on the rear of this manual.
These statements do not affect the statutory rights of a consumer.
ROBERTS RADIO TECHNICAL SERVICES
97-99 Worton Road
Isleworth Middlesex
TW7 6EG
Technical Helpline :- 020 8758 0338 (Mon-Fri during office hours)
© 2010 Roberts Radio Limited
Issue 1
Download from Www.Somanuals.com. All Manuals Search And Download.
|