Roberts Radio Cassette Player TCR 200 User Guide

43-473.fm Page 1 Friday, August 13, 1999 9:21 AM  
Cat. No. 43-473  
OWNER’S MANUAL  
Please read before using this equipment.  
TCR-200  
Telephone Cassette Recorder  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 3 Friday, August 13, 1999 9:21 AM  
READ THIS BEFORE  
INSTALLATION  
Warning: To reduce the risk of  
fire or shock hazard, do not ex-  
pose this product to rain or mois-  
ture.  
Each device that you connect to the  
phone line draws power from the phone  
line. We refer to this power draw as the  
device’s ringer equivalence number, or  
REN. The REN is on the bottom of your  
telephone cassette recorder.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVIC-  
ING TO QUALIFIED PERSONNEL.  
If you are using more than one device  
on the line, add up all the RENs. If the  
total is more than five, your phone might  
not ring and your telephone cassette re-  
corder might not record. In rural areas, a  
total REN of three might impair ringer  
operation. If ringer operation is impaired,  
disconnect one of the devices from the  
line.  
This symbol is intended to alert you to  
the presence of uninsulated danger-  
ous voltage within the product’s enclo-  
sure that might be of sufficient  
magnitude to constitute a risk of elec-  
tric shock. Do not open the product’s  
case.  
This symbol is intended to inform you  
that important operating and mainte-  
nance instructions are included in the  
literature accompanying this product.  
FCC STATEMENT  
!
Your telephone cassette recorder com-  
plies with Part 68 of FCC Rules. You  
must, upon request, provide the FCC  
registration number and the REN to your  
phone company. Both numbers are on  
the bottom of your telephone cassette  
recorder.  
Note: You must not connect your tele-  
phone cassette recorder to:  
• coin-operated systems  
• party-line systems  
• most electronic key phone systems  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 4 Friday, August 13, 1999 9:21 AM  
CONTENTS  
Preparation .............................................................................................................. 5  
Connecting Power .............................................................................................. 5  
Using AC Power ........................................................................................... 5  
Using Battery Power .................................................................................... 5  
Installation ............................................................................................................... 6  
Connecting Directly to the Phone Line ............................................................... 6  
Connecting to A Phone ....................................................................................... 6  
Using an Earphone ............................................................................................. 7  
Listening Safely ............................................................................................ 7  
Operation ................................................................................................................. 8  
Setting the Beep ................................................................................................. 8  
Loading a Cassette Tape .................................................................................... 8  
Recording a Phone Conversation ....................................................................... 8  
Setting the Record Mode ............................................................................. 9  
Setting the Sensitivity Level ......................................................................... 9  
Setting the Recording Speed ..................................................................... 10  
Listening While You Record ....................................................................... 10  
Regular Recording ............................................................................................ 10  
Playing a Tape .................................................................................................. 11  
Fast-Forward and Rewind .......................................................................... 11  
Using the Tape Counter ............................................................................. 11  
Care and Maintenance .......................................................................................... 12  
Tape Tips and Techniques ................................................................................ 13  
Preventing Accidental Erasure ................................................................... 13  
Restoring Tape Tension and Sound Quality ............................................... 13  
Cleaning the Tape-Handling Parts ............................................................. 14  
The FCC Wants You to Know ........................................................................... 14  
Lightning ........................................................................................................... 14  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 5 Friday, August 13, 1999 9:21 AM  
PREPARATION  
Using Battery Power  
CONNECTING POWER  
Your telephone cassette recorder can  
use four AA batteries (not supplied) for  
power. For the best performance and  
longest life, we recommend alkaline bat-  
teries, such as Cat. No. 23-552.  
Using AC Power  
You can power your telephone cassette  
recorder from AC power using an op-  
tional AC adapter, such as RadioShack  
Cat. No. 273-1662.  
Follow these steps to install batteries.  
CAUTION  
Caution: You must use a 120V AC/6V  
DC adapter that delivers at least 300  
milliamps. Its center tip must be set to  
negative, and its plug must properly fit  
ALWAYS DISCONNEC  
LINES FROM THE WA  
SERVICING OR DISA  
EQUIPMENT, OR REP  
+
+
+
+
DC 6V  
the TCR-200’s  
jack. The recom-  
mended adapter meets these require-  
ments. Using an adapter that does not  
meet these requirements could damage  
the telephone cassette recorder or the  
adapter.  
1. Press the battery compartment  
cover’s tab and lift off the cover.  
2. Insert the batteries into the compart-  
ment, as indicated by the polarity  
symbols (+ and –) marked inside the  
compartment.  
Follow these steps to connect your tele-  
phone cassette recorder to AC power.  
3. Replace the cover.  
MIC  
EAR  
DC 6V 300ma  
TEL  
OFF ON  
VOX NORM  
STD EXT  
SPEED  
MONITOR  
REC MODE  
Caution: Do not mix old and new batter-  
ies, different types of batteries (stan-  
dard, alkaline, or rechargeable), or  
rechargeable batteries of different ca-  
pacities.  
1. Set the AC adapter’s voltage switch  
to 6V.  
2. Insert the 5.5 mm outer diameter/  
2.1 mm inner diameter barrel plug  
into the adapter’s cord to read TIP –.  
Replace the batteries when the record-  
ing indicator dims.  
3. Insert the plug into the telephone  
DC 6V  
cassette recorder’s  
jack.  
4. Plug the adapter into a standard AC  
outlet.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 6 Friday, August 13, 1999 9:21 AM  
INSTALLATION  
You can connect the telephone cassette  
recorder directly to the phone line or a  
single phone. Select a location for your  
telephone cassette recorder that is out  
of the way of normal activities.  
CONNECTING TO  
A PHONE  
You can use the supplied handset  
adapter to connect the telephone cas-  
sette recorder to the same phone you  
plan to talk on. When connected this  
way, the recorder only records the  
phone conversations on that phone.  
CONNECTING DIRECTLY  
TO THE PHONE LINE  
When connected to the phone line, the  
recorder records phone conversations  
on any phone on that line. Follow these  
steps to connect the telephone cassette  
recorder to the phone line.  
Important: The law in some areas re-  
quires that all parties on the phone line  
be able to hear a beep indicating the  
conversation is being recorded. If you  
connect the telephone cassette recorder  
to your phone using the supplied dual-  
prong cord and handset adapter, all par-  
ties on the phone line might not hear a  
beep during recording.  
MIC  
EAR  
DC 6V 300ma  
TEL  
OFF ON  
VOX NORM  
STD EXT  
SPEED  
MONITOR  
REC MODE  
We recommend you check the laws in  
your area. If it is unlawful to record with-  
out a beep sounding, or if you are un-  
sure, connect the telephone cassette  
recorder as described in “Connecting Di-  
rectly to the Phone Line” to ensure the  
beep will sound.  
Dual-Prong Cord  
1. Plug the supplied dual-prong cord  
into the recorder’s TEL jacks.  
2. Insert the dual-prong cord’s modular  
plug into a modular phone line jack.  
Note: The RadioShack Cat. No. 279-  
357 adapter might be required for some  
installations.  
Notes:  
• If the phone line jack is not a  
modular jack, you must update  
the wiring. You can convert the  
wiring yourself, using jacks and  
adapters available at your local  
RadioShack store, or you can let  
the phone company update the  
wiring for you.  
1. Plug the supplied dual-prong cord  
into the recorder’s TEL jacks.  
2. Insert the dual-prong cord’s modular  
plug and the phone’s handset cord  
into the handset adapter.  
• The USOC number of the jack to  
be installed is RJ11C.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 7 Friday, August 13, 1999 9:21 AM  
H
Handset Cord  
MIC  
EAR  
DC 6V 300mA  
TEL  
OFF ON  
VOX NORM  
STD EXT  
SPEED  
MONITOR  
REC MODE  
Handset Adapter  
MIC  
EAR  
DC 6V 300ma  
OFF ON  
VOX NORM  
STD EXT  
SPEED  
MONITOR  
REC MODE  
d  
Dual-Prong Cord  
Note: The speaker automatically dis-  
connects when you plug in an earphone.  
Note: Plug the dual-prong cord’s  
plug into the larger modular jack and  
the handset cord’s plug into the  
smaller jack.  
Listening Safely  
3. Insert the handset adapter into the  
telephone’s modular handset jack.  
To protect your hearing, follow these  
guidelines when you use an earphone.  
Handset Cord  
• Do not listen at extremely high vol-  
ume levels. Extended high-volume  
listening can lead to permanent  
hearing loss.  
Handset Adapter  
• Set the volume to its lowest level  
before you begin listening. After you  
put on the earphone, adjust the vol-  
ume to a comfortable listening level.  
MIC  
EAR  
DC 6V 300ma  
OFF ON  
VOX NORM  
STD EXT  
SPEED  
MONITOR  
REC MODE  
Dual-Prong Cord  
• Do not increase the volume once  
you have established a comfortable  
listening level. Over time, your ears  
adapt to the volume level, so a vol-  
ume level that does not cause dis-  
comfort might still damage your  
hearing.  
USING AN EARPHONE  
To connect an earphone (not supplied),  
1
insert the earphone’s /8-inch plug into  
EAR  
the  
jack on the back of the tele-  
phone cassette recorder. You can find a  
wide selection of earphones at your lo-  
cal RadioShack store.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 8 Friday, August 13, 1999 9:21 AM  
OPERATION  
2. Press STOP/EJECT to open the cas-  
sette compartment door. Put the  
cassette in the compartment with  
the cassette’s open edge facing you  
and the full reel on the left.  
SETTING THE BEEP  
You can set the telephone cassette re-  
corder to beep every 15 seconds while  
recording.  
Note: You might be legally required to  
set BEEP TONE to ON when recording,  
so all parties know the conversation is  
being recorded. Check the laws in your  
area.  
3. Close the door.  
1. Remove the battery compartment  
cover and remove the batteries, if  
installed.  
Notes:  
• You can buy cassettes of varying  
lengths at your local RadioShack  
store.  
2. Set BEEP TONE to ON. The tele-  
phone cassette recorder beeps ev-  
ery 15 seconds while recording.  
ALWAYS DISCONNECT ALL TELEPHONE  
SERVICING OR DSASSEMBLNG THIS  
EQUIPMENT, OR REPLACING BATTERIES.  
• Replace the tape at least once a  
year, or more often if it is used  
heavily.  
+
- - -  
DC 6V  
---  
(UM/SUM-3) X4  
+
BEEP TONE  
ON  
+
OFF  
---  
+
RECORDING A PHONE  
CONVERSATION  
3. Replace the batteries and the cover.  
You can record both sides of a conver-  
sation on any phone connected to the  
same phone line as the recorder.  
LOADING A CASSETTE  
TAPE  
1. Set REC MODE, the sensitivity level,  
SPEED, and MONITOR to the desired  
settings. (See “Setting the Record  
Mode” on Page 9, “Setting the Sen-  
sitivity Level” on Page 9, “Setting  
the Recording Speed” on Page 10,  
and “Listening While You Record”  
on Page 10.)  
Follow these steps to install a cassette  
tape (not supplied) in the recorder.  
1. Turn the cassette’s hub with a pencil  
to take up any tape slack.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 9 Friday, August 13, 1999 9:21 AM  
2. Press RECORD. Both RECORD and  
PLAY lock down. When RECORD is  
pressed down, every call made or  
received is recorded.  
Setting the Record Mode  
When REC MODE is set to VOX, the re-  
corder begins recording when it receives  
sound through the microphone or phone  
line, and stops recording when it does  
not receive sound for about 5 seconds.  
Notes:  
• If you set REC MODE to VOX,  
when both parties are silent for  
about 5 seconds, the recorder  
stops recording until someone  
starts speaking again.  
DC 6V 300mA  
STD EXT  
VOX NORM  
OFF ON  
MONITOR  
REC MODE  
SPEED  
• The VOLUME setting does not  
affect the recording level.  
Set REC MODE to NORM to record con-  
tinuously until the tape reaches the end  
or you press STOP/EJECT.  
• VU/LEVEL flashes during record-  
ing.  
Setting the Sensitivity Level  
VU  
LEVEL  
0 0 0  
MIC  
When you set REC MODE to VOX, you  
must set the sensitivity level located on  
the bottom of the recorder. H (high) is  
the most sensitive setting and requires  
only a soft sound to begin recording. L  
(low) is the least sensitive setting and  
requires a louder sound to begin record-  
ing. If the tape does not stop after about  
5 seconds of silence, set SENSITIVITY to  
TCR-200 VOICE ACTIVATED  
TELEPHONE CASSETTE RECORDER  
To temporarily stop recording,  
press PAUSE. To resume record-  
ing, press PAUSE again.  
REVIEW  
CUE  
PLAY  
REWIND  
FAST-F  
STOP/EJECT  
PAUSE  
RECORD  
M (medium) or L (low).  
SENSITIVITY  
L
M
H
CAUTION  
• If the tape reaches the end during  
recording, it automatically  
a
releases RECORD and PLAY, and  
stops.  
ALWAYS DISCONNECT ALL TELEPHONE  
LINES FROM THE WALL OUTLETS BEFORE  
SERVICING OR DISASSEMBLING THIS  
EQUIPMENT, OR REPLACING BATTERIES.  
3. To stop recording, press STOP/  
EJECT.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 10 Friday, August 13, 1999 9:21 AM  
Setting the Recording Speed  
REGULAR RECORDING  
Set SPEED to EXT (extended) to record  
at a slower speed and a lower quality  
than regular speed, but extend the re-  
cording time. Tapes recorded with  
SPEED set to EXT must be played back  
with the recorder set to EXT.  
You can use your telephone cassette re-  
corder as a regular cassette recorder for  
recording dictation or conversations. For  
regular recording, be sure the dual-  
prong cord is not plugged in.  
Set REC MODE to NORM for continuous  
recording, then press RECORD. Both  
RECORD and PLAY lock down. Then  
speak into the built-in microphone from  
a distance of about 12 inches.  
Set SPEED to STD (standard) to record  
at regular speed. When you record with  
SPEED set to STD, you can play back  
the tape on this recorder (with SPEED  
set to STD) or any other cassette tape  
player.  
REVIEW  
CUE  
PLAY  
REWIND  
FAST-F  
STOP/EJECT  
PAUSE  
RECORD  
DC 6V 300mA  
STD EXT  
SPEED  
VOX NORM  
OFF ON  
MONITOR  
REC MODE  
Note: To temporarily stop recording,  
press PAUSE. To resume recording,  
press PAUSE again.  
Listening While You Record  
Set MONITOR to ON to listen to a conver-  
sation through the telephone cassette  
recorder’s speaker as it is being record-  
ed. Slide VOLUME to a comfortable lis-  
tening level.  
To stop recording, press STOP/EJECT.  
DC 6V 300mA  
STD EXT  
SPEED  
VOX NORM  
OFF ON  
MONITOR  
REC MODE  
Note: While you record your own phone  
conversation, set MONITOR to OFF. Oth-  
erwise, it might cause a high-pitched  
tone to sound through your telephone  
handset or through the telephone cas-  
sette recorder’s speaker.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 11 Friday, August 13, 1999 9:21 AM  
Note: The recorder automatically stops  
when it reaches the end of the tape.  
PLAYING A TAPE  
SPEED  
1. Set  
to the desired tape  
speed (see “Setting the Recording  
Speed” on Page 10).  
Using the Tape Counter  
PLAY  
. Playback begins.  
2. Press  
Note: Press  
stop the tape while you play it. Press  
You can use the tape counter to mark  
positions on a cassette tape during re-  
cording or playback. Before you play a  
cassette tape, rewind the cassette tape  
and press the button to the right of the  
tape counter to set it to 000. As the cas-  
sette tape moves, the counter advanc-  
es. Note the tape counter reading at the  
position you want to return to later.  
PAUSE  
to temporarily  
PAUSE  
again to resume play.  
VOLUME  
3. Adjust  
to a comfortable lis-  
tening level.  
STOP/EJECT  
4. Press  
to stop play. If  
the cassette tape plays to the end,  
the cassette deck automatically  
PLAY  
releases  
and stops.  
VU  
LEVEL  
0 0 0  
MIC  
Fast-Forward and Rewind  
REVIEW  
CUE  
PLAY  
REWIND  
FAST-F  
STOP/EJECT  
PAUSE  
RECORD  
TCR-200 VOICE ACTIVATED  
TELEPHONE CASSETTE RECORDER  
CUE/  
When the tape is stopped, press  
FAST-F  
to wind the tape rapidly forward  
REVIEW/REWIND  
or  
to wind the tape rap-  
STOP/EJECT  
idly backward. Press  
stop the tape.  
to  
CUE/FAST-F  
During play, hold down  
or  
REVIEW/REWIND  
to hear playback as  
the tape fast-forwards or rewinds to find  
desired locations on a tape quickly.  
When you release the button, the tele-  
phone cassette recorder returns to nor-  
mal speed.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 12 Friday, August 13, 1999 9:21 AM  
CARE AND MAINTENANCE  
Your TCR-200 Telephone Cassette Recorder is an example of superior design and  
craftsmanship. The following suggestions will help you care for your telephone cas-  
sette recorder so you can enjoy it for years.  
Keep the telephone cassette recorder dry. If it gets wet, wipe it dry im-  
mediately. Liquids might contain minerals that can corrode the electron-  
ic circuits.  
Use and store the telephone cassette recorder only in normal temper-  
ature environments. Temperature extremes can shorten the life of elec-  
tronic devices, damage batteries, and distort or melt plastic parts.  
Keep the telephone cassette recorder away from dust and dirt, which  
can cause premature wear of parts.  
Handle the telephone cassette recorder gently and carefully. Dropping  
it can damage circuit boards and cases and can cause the telephone  
cassette recorder to work improperly.  
Use only fresh batteries of the required size and recommended type.  
Batteries can leak chemicals that damage your telephone cassette re-  
corder’s electronic parts.  
Wipe the telephone cassette recorder with a damp cloth occasionally to  
keep it looking new. Do not use harsh chemicals, cleaning solvents, or  
strong detergents to clean the telephone cassette recorder.  
Modifying or tampering with the telephone cassette recorder’s internal components  
can cause a malfunction and might invalidate its warranty and void your FCC authori-  
zation to operate it. If your telephone cassette recorder is not performing as it should,  
take it to your local RadioShack store for assistance. If the trouble is affecting the  
telephone lines, the phone company can ask you to disconnect your cassette record-  
er until you have resolved the problem.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 13 Friday, August 13, 1999 9:21 AM  
If you later decide to erase or record  
over the tape, you can place a piece of  
tape over the holes.  
TAPE TIPS AND  
TECHNIQUES  
The following tips can help you get the  
best performance and the longest life  
from your telephone cassette recorder.  
Tape Over Side A Tab  
Note: Do not use endless or C-120 cas-  
sette tapes. C-120 tape is very thin and  
can tangle easily.  
Note: When covering the holes, cover  
only the portions that were originally pro-  
tected by the plastic tabs.  
Preventing Accidental Erasure  
Most cassette tapes have two erase-  
protection tabs — one for each side of  
the tape. When a tab is in place, you can  
erase or record on that tape side. When  
the tab is not in place, you cannot erase  
or record on that side.  
Restoring Tape Tension and  
Sound Quality  
After you play a cassette tape several  
times, the tape might become tightly  
wound on the cassette reels. This can  
cause playback sound quality to deterio-  
rate.  
To prevent your recordings from being  
accidentally erased or recorded over,  
carefully break off the erase-protection  
tabs using a screwdriver or similar tool.  
Side A  
To restore the sound quality, fast-for-  
ward the tape from the beginning to the  
end of one side, then completely rewind  
it. Then loosen the tape reels by gently  
tapping each side of the cassette’s outer  
shell on a flat surface.  
Side A Tab  
Side B Tab  
Caution: Be careful not to damage the  
cassette when tapping it. Do not touch  
the exposed tape or allow any sharp ob-  
jects near the cassette.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 14 Friday, August 13, 1999 9:21 AM  
Cleaning the Tape-Handling  
Parts  
THE FCC WANTS YOU TO  
KNOW  
Dirt, dust, or particles of the tape’s coat-  
ing can accumulate on the tape heads  
and other parts that the tape touches.  
This can greatly reduce the telephone  
cassette recorder’s performance. Use  
the following cleaning procedure after  
about every 20 hours of operation.  
In the unlikely event that your telephone  
cassette recorder causes problems on  
the phone line, the phone company can  
disconnect your service. The phone  
company attempts to notify you in ad-  
vance. If advance notice is not practical,  
the phone company notifies you of your  
right to file a complaint with the FCC.  
1. Remove the batteries and discon-  
nect the AC adapter.  
Also, the phone company can make  
changes to its lines, equipment, opera-  
tions, or procedures that could affect the  
operation of your telephone cassette re-  
corder. The phone company notifies you  
of these changes in advance, so you  
can take steps to prevent interruption of  
your phone service.  
2. Open the cassette compartment  
door.  
3. Hold down the protection tab sensor  
in the tape compartment while you  
press RECORD to expose the tape-  
handling parts.  
4. Use a swab dipped in tape head  
cleaning solution or denatured alco-  
hol to gently clean the record/play  
head, pinch roller, capstan, erase  
head, and tape guides.  
LIGHTNING  
Your telephone cassette recorder has  
built-in protection circuits to reduce the  
risk of damage from surges in phone  
and power line current. These protection  
circuits meet or exceed FCC require-  
ments. However, lightning striking the  
phone line or power lines can damage  
your telephone cassette recorder.  
Tape Guides  
Rubber  
Pinch Roller  
r  
Capstan  
Recordand  
CottonSwab  
Erase Heads  
r
s  
5. When you finish cleaning, press  
STOP/EJECT and close the compart-  
ment.  
Lightning damage is not common. Nev-  
ertheless, if you live in an area that has  
frequent electrical storms, we suggest  
that you unplug your telephone cassette  
recorder during storms to reduce the  
possibility of damage.  
Your local RadioShack store carries a  
complete line of tape head-cleaning ac-  
cessories.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 15 Friday, August 13, 1999 9:21 AM  
NOTES  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43-473.fm Page 16 Friday, August 13, 1999 9:21 AM  
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workman-  
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned  
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING  
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED  
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-  
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY  
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-  
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-  
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS  
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-  
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-  
cidental or consequential damages, so the above limitations or exclusions may not apply to you.  
In the event of a product defect during the warranty period, take the product and the RadioShack  
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-  
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and  
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase  
price. All replaced parts and products, and products on which a refund is made, become the prop-  
erty of RadioShack. New or reconditioned parts and products may be used in the performance of  
warranty service. Repaired or replaced parts and products are warranted for the remainder of the  
original warranty period. You will be charged for repair or replacement of the product made after the  
expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,  
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or  
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs  
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs  
of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102  
We Service What We Sell  
3/97  
RadioShack  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
7A8  
Printed in Hong Kong  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q Logic Automobile Accessories APS 610 User Guide
QSC Audio Speaker SC 2150 User Guide
Radica Games Games 74007 User Guide
Radio Shack Mouse 26 592 User Guide
Raymarine GPS Receiver Ray54E User Guide
Raymarine Portable Radio Ray230 User Guide
Samsung Bluetooth Headset GH68 18475A User Guide
Samsung Digital Camera VP MS10BL User Guide
Samsung Speaker System HW F550 User Guide
Sanyo Battery Charger UF103450P User Guide