Medium Format Digital SLR Camera
Operating Manual
To ensure the best performance from your camera,
please read the Operating Manual before using the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
FOR USING YOUR CAMERA
SAFELY
• Some portions of the camera heat up during use. There is a risk
of low temperature burns when holding such portions for long
periods.
We have paid close attention to the safety of this camera. When using
this camera, we request your special attention regarding items marked
with the following symbols.
• Should the monitor be damaged, be careful of glass fragments.
Also, be careful not to allow the liquid crystal to get on your skin
or in your eyes or mouth.
• Depending on your individual factors or physical condition, the
use of the camera may cause itching, rashes or blisters. In case
of any abnormality, stop using the camera and get medical
attention immediately.
This symbol indicates that ignoring this item could
Warning
cause serious personal injuries.
This symbol indicates that ignoring this item could
Caution cause minor or medium personal injuries, or loss of
property.
About the Battery Charger and AC Adapter
ABOUT THE CAMERA
Warning
• Always use the battery charger and AC adapter exclusively
developed for this camera, with the specified power and voltage.
Using a battery charger or AC adapter not exclusive to this
camera, or using the exclusive battery charger or AC adapter
with an unspecified power or voltage can cause a fire, electric
shock, or camera breakdown. The specified voltage is 100 - 240V
AC.
Warning
• Do not disassemble or modify the camera. High voltage areas
are present inside the camera, with the risk of electric shock.
• If the camera interior is exposed due to dropping or otherwise
damaging the camera, never touch the exposed portion. There is
a risk of electric shock.
• Do not aim the camera at the sun or other strong light sources
when taking pictures or leave the camera sitting in direct sunlight
with the lens cap off. Doing so may cause the camera to
malfunction or cause a fire.
• Do not disassemble or modify the product. This can cause a fire
or electrical shock.
• If the generation of smoke or strange odor from the product or
other abnormality occurs, immediately discontinue using and
consult your nearest service center. Continued use can cause a
fire or electrical shock.
• Do not look at the sun or other strong light sources through the
lens. Doing so may lead to a loss of eyesight or cause vision to
be impaired.
• If water should happen to get inside the product, consult your
nearest service center. Continued use can cause a fire or
electrical shock.
• If any irregularities occur during use, such as smoke or a strange
odor, stop use immediately, remove the battery or the AC
adapter, and contact your nearest service center. Continued use
can cause a fire or electrical shock.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you see a lightning flash or hear thunder during use of the
battery charger or AC adapter, unplug the power plug and
discontinue using. Continued use can cause damage to the
product, fire or electrical shock.
About the Battery
Warning
• Wipe off the power plug if it should become covered with dust.
Accumulated dust may cause a fire.
• If any leakage from the battery should come in contact with your
eyes, do not rub them. Flush your eyes with clean water and get
medical attention immediately.
• To reduce the risk of hazards, use only CSA/UL certified power
supply cord set, cord is Type SPT-2 or heavier, minimum NO.18
AWG copper, one end with a molded-on male attachment plug
cap (with a specified NEMA configuration), and the other is
provided with a molded-on female connector body (with a
specified IEC nonindustrial type configuration) or the equivalent.
Caution
• Only use the specified battery with this camera. Use of other
batteries may cause an explosion or fire.
• Do not disassemble the battery. Disassembling the battery may
cause an explosion or leakage.
• Remove the battery from the camera immediately if it becomes
hot or begins to smoke. Be careful not to burn yourself during
removal.
Caution
• Do not place or drop heavy objects on or forcefully bend the AC
plug cord. Doing so may damage the cord. Should the AC plug
cord be damaged, consult your nearest service center.
• Do not touch or short-circuit the terminal area of the AC plug cord
while the cord is plugged in.
• Keep wires, hairpins, and other metal objects away from the +
and - contacts of the battery.
• Do not short the battery or dispose of the battery in fire. This can
cause an explosion or fire.
• Do not handle the power plug with wet hands. This can cause an
electric shock.
• If any leakage from the battery should come in contact with skin
or clothing, it may cause irritation to the skin. Wash the affected
areas thoroughly with water.
• Do not drop the product, or subject it to violent impact. This can
cause the product to breakdown.
• Do not use the battery charger D-BC90 to charge batteries other
than the rechargeable lithium-ion battery D-LI90. Attempting to
charge other types of batteries may cause an explosion or
heating, or may damage the battery charger.
• Precautions for D-LI90 Battery Usage:
USE SPECIFIED CHARGER ONLY.
- RISK OF FIRE AND BURNS.
- DO NOT INCINERATE.
- DO NOT DISASSEMBLE.
- DO NOT SHORT CIRCUIT.
- DO NOT EXPOSE TO HIGH TEMP. (140°F / 60°C)
SEE MANUAL.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep the Camera and its Accessories out
of the Reach of Small Children
About the Battery and Charger
• To keep the battery in optimum condition, avoid storing it in a fully
charged state or in high temperatures.
Warning
• If the battery is left inserted and the camera is not used for a long
time, the battery will over-discharge and shorten the battery’s life.
• Charging the battery a day before use or on the day of use is
recommended.
• Do not place the camera and its accessories within the reach of
small children.
1. If the product falls or is operated accidentally, it may cause
serious personal injuries.
• The AC plug cord provided with this camera is developed
exclusively for the battery charger D-BC90. Do not use it with
other devices.
2. Wrapping the strap around a neck may cause suffocation.
3. To avoid the risk of a small accessory such as the battery or
memory cards from being swallowed by mistake, keep them
out of the reach of small children. Seek medical attention
immediately if an accessory is accidentally swallowed.
Precautions on Carrying and Using Your
Camera
• Do not subject the camera to high temperatures or high humidity.
Do not leave the camera in a vehicle, as the temperature can get
very high.
Care to be Taken During Handling
Before Using Your Camera
• Do not subject the camera to strong vibrations, shocks, or
pressure. Use a cushion to protect the camera from vibrations of
motorcycles, automobiles, or ships.
• When traveling, take the Worldwide Service Network listing that
is included in the package. This will be useful if you experience
problems abroad.
• The temperature range for camera use is -10°C to 40°C (14°F to
104°F).
• When the camera has not been used for a long time, confirm that
it is still working properly, particularly prior to taking important
pictures (such as at a wedding or when traveling). Contents of the
recording cannot be guaranteed if recording, playback or
transferring your data to a computer, etc. is not possible due to a
malfunction of your camera or recording media (memory cards),
etc.
• The monitor may appear black at high temperatures, but will
return to normal at normal temperatures.
• The monitor may respond more slowly at low temperatures. This
is due to liquid crystal properties, and is not a malfunction.
• Sudden temperature changes will cause condensation on the
inside and outside of the camera. Place the camera in your bag
or a plastic bag, and remove it after temperatures of the camera
and surroundings are equalized.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Avoid contact with garbage, mud, sand, dust, water, toxic gases,
or salt. These could cause the camera to breakdown. Wipe the
camera to dry off any rain or water drops.
About SD Memory Cards
• The SD Memory Card is equipped
with a write-protect switch. Setting
the switch to LOCK prevents new
data from being recorded on the
card, the stored data from being
deleted, and the card from being
formatted by the camera or
computer.
• Do not press on the monitor with excessive force. This could
cause it to break or malfunction.
• Be careful not to overtighten the screw in the tripod socket when
using a tripod.
Write-protect
switch
Cleaning Your Camera
• The SD Memory Card may be hot when removing the card
immediately after using the camera.
• Do not clean the camera with organic solvents such as thinner,
alcohol, and benzine.
• Do not remove the SD Memory Card or turn off the power while
the card is being accessed. This may cause the data to be lost or
the card to be damaged.
• Use a lens brush to remove dust accumulated on the lens. Never
use a spray blower for cleaning as it may damage the lens.
• Please contact your nearest service center for professional
cleaning of the CMOS sensor. (This will involve a fee.)
• Periodic inspections are recommended every one to two years to
maintain high performance.
• Do not bend the SD Memory Card or subject it to violent impact.
Keep it away from water and store away from high temperatures.
• Do not remove the SD Memory Card while formatting. The card
may be damaged and become unusable.
• Data on the SD Memory Card may be deleted in the following
circumstances. We do not accept any liability for data that is
deleted if
Storing Your Camera
• Do not store the camera with preservatives or chemicals. Storage
in high temperatures and high humidity can cause mold to grow
on the camera. Remove the camera from its case and store it in
a dry and well-ventilated place.
1. the SD Memory Card is mishandled by the user.
2. the SD Memory Card is exposed to static electricity or
electrical interference.
3. the SD Memory Card has not been used for a long time.
• Avoid using or storing the camera where it may be exposed to
static electricity or electrical interference.
4. the SD Memory Card or the battery is removed while the card
is being accessed.
• If the SD Memory Card is not used for a long time, the data on the
card may become unreadable. Be sure to regularly make a
backup of important data on a computer.
• Avoid using or storing the camera in direct sunlight or in locations
where it may be exposed to rapid changes in temperature or to
condensation.
• Format new SD Memory Cards. Also format SD Memory Cards
previously used with other cameras.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Please note that deleting data stored on an SD Memory Card, or
formatting an SD Memory Card does not completely erase the
original data. Deleted data can sometimes be recovered using
commercially available software. If you are going to discard, give
away or sell your SD Memory Card, you should ensure that the
data on the card is completely deleted or the card itself is
destroyed if it contains any personal or sensitive information.
• The data on your SD Memory Card should be managed at your
own risk.
Provided Manuals
This camera comes with two manuals: “Operating Manual” (this
book) and “Menu Reference”. Use these as needed.
Operating Manual
Describes the necessary preparations before use
and the basic operations of your camera. The
About Eye-Fi Cards
Menu Reference
• An SD Memory Card with a built-in wireless LAN (“Eye-Fi card”)
can be used with this camera.
Describes the functions that can be set when F
is pressed and the product specifications. After you
read the “Operating Manual” and become familiar
with the basic operations of your camera, you can
carry the “Menu Reference” with you as a handy
reference guide. The “Menu Reference” contains
pages R1 to R57.
• Use of an access point and an Internet connection are required
for transferring images via wireless LAN. For details, refer to the
Eye-Fi website. (http://www.eye.fi)
• Update your Eye-Fi card to the latest firmware before using it.
• Set [Action Mode] of [Wireless Memory Card] to [OFF], or do not
use an Eye-Fi card in a location where the use of wireless LAN
devices is restricted or prohibited, such as airplanes.
• Eye-Fi cards can be used only in the country in which the card
was purchased. Please observe all local laws governing the
Eye-Fi card usage.
The following symbols indicate reference page numbers with
related information.
y Refer to another location within the same
• This camera features a function to enable/disable the
communication function of the Eye-Fi card, however, we do not
guarantee the operability of all Eye-Fi card functions.
• Refer to the Eye-Fi card manual for details on how to use the
card.
document.
w Refer to a location in the other document.
• Please contact the Eye-Fi card manufacturer regarding any
malfunctions or problems concerning Eye-Fi cards.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Manual Contents
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Playback and Processing
Functions
71
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding User Registration
In order to better serve you, we request that you complete the user registration, which can be found on the CD-ROM supplied with the camera
(p.91) or on our website.
Thank you for your cooperation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Contents of the Package
1
The following accessories are packaged with this camera.
Check that all accessories are included before using your camera.
Hot shoe cover FK
(Installed on camera)
Sync socket 2P cap
(Installed on camera)
Standard eyecup
(Installed on camera)
Large eyecup 645
O-EC107
Body mount cap 645
(Installed on camera)
Triangular ring and protective cover
(Installed on camera)
Strap
O-ST150
Rechargeable Lithium-ion Battery
D-LI90
Battery charger
D-BC90
AC plug cord
Software (CD-ROM)
S-SW150
Operating Manual (this manual)
Menu Reference
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and Functions of Working Parts
1
Hot shoe
Strap lug
Lens information contacts
Card cover
Lens mount index
Sync socket
Self-timer lamp/
Remote control receiver
Tripod socket
Mirror
Terminal cover
AF coupler
Lens unlock button
Image plane
indicator
LCD Panel
Stereo
microphones
Battery cover unlock knob
SD2 slot
SD1 slot
Diopter
adjustment ring
Speaker
Strap lug
Viewfinder
USB 3.0 terminal
(micro B)
Microphone
terminal
Tiltable monitor
Cable switch
terminal
DC input
terminal
Battery
cover
Card access
lamp
HDMI terminal
(Type D)
Self-timer lamp/
Remote control receiver
Tripod socket
* The front and rear views show the camera with the Hot shoe cover FK removed.
Caution
•
Although the angle of the tiltable monitor can be changed (raised or lowered), the monitor cannot be moved in the left/right direction. Do not twist
or apply strong force to the movable section, or hit the viewfinder part with the monitor. Always return to its original position when not in use.
• Be sure to close the terminal cover correctly to keep out dust and moisture.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3 EV Compensation button (J)
Operating Controls
Press to change the exposure compensation value. (p.50)
1
4 Main switch
1 2 3
5 Front e-dial (Q)
7
8
You can change the menu category when a menu screen is
displayed. (p.42)
4
5
9
0
a
In playback mode, use this to select a different image. (p.39)
6 Lens unlock button
Press to detach the lens on the camera. (p.26)
6
7 Metering mode switching dial
b c d
e
8 Lock button (7)
Temporarily disables e-dial and button operations to prevent
misoperation. (w p.R43)
9 AF area button (6)
g
h
f
Press to change the AF point. (p.45)
0 Exposure Bracketing button (5)
i
j
a RAW/Fx button (O)
k
l
m
You can assign a function to this button. (w p.R20)
b Mode dial lock button
n o
1 Shutter release button
p
q
r
Press to allow the mode dial to be turned. (p.49)
c Mode dial
d Stills/Movie switching dial
In playback mode, press halfway to switch to capture mode.
Switches between A (Still capture) mode and C (Movie
2 ISO button (N)
Press to change the ISO sensitivity. (p.47)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
e Rear e-dial (R)
l Four-way controller (ABCD)
You can change the menu tabs when a menu screen is displayed.
Displays the Drive Mode, Flash Mode, White Balance or Custom
1
When a menu or the control panel is displayed, use this to move
the cursor or change the item to set.
You can change the camera settings when the control panel is
Press B in single image display of the playback mode to display
In playback mode, use this to magnify an image or display multiple
When selecting the area of an image to magnify or to use as a
focusing area, you can move the area diagonally by pressing two
keys at the same time.
f AF mode switching dial
m AF point change/Card slot switching button (c / d)
g Mirror Up dial
In playback mode, press this button to switch between the memory
cards for playback that are inserted in the two slots, SD1 and SD2.
Enables shooting with the mirror raised up. (p.63)
h Illumination button (8)
i AE Lock button (H)
n Green button (M)
In playback mode, the JPEG image that was just taken is also
Resets the values being adjusted.
o Live View/REC/Delete button (K/a/L)
Displays the Live View image. (p.39)
j AF button (I)
Available for adjusting focus, instead of pressing the shutter
k OK button (E)
p INFO button (G)
When a menu or the control panel is displayed, press this button to
confirm the selected item.
q MENU button (F)
Displays a menu. Press this button while the menu is displayed to
r Playback button (3)
Switches to playback mode. Press the button again to switch to
capture mode. (p.39)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Hold the bottom of the
Button and Dial Operations
You can operate both a button and e-dial, such as J and R or
5 and Q, to change the settings using either of the following
methods.
monitor and lift upward.
1
Operation
Confirming the Setting
Turn the dial while pressing the
button.
Take your finger off the button.
4 Adjust the angle.
Perform Step 3 and then Step 2 to retract the monitor.
Press the button, take your finger Press the button again or wait
off the button, and then turn the until the exposure metering timer
dial.
goes off.
Caution
Hereafter, this Operating Manual explains by using the “Turn the
dial while pressing the button” operation.
For the 7 and 6 buttons, only the operation of turning R
while pressing the button is available.
• Do not twist or apply strong force to the movable section.
• Be careful not to hit the viewfinder part with the monitor.
Adjusting the Angle of the Monitor
1 Hold the camera grip with
your right hand and hold the
top of the monitor with your
left hand.
2 Slowly lower until it stops.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ISO AUTO Setting
Adjustment Range
12345
12345
Display Indicators
1/
F
250
1600
5.6
100-3200
1
2000
Monitor
1234
1234
05/05/2014 10:30
The various indicators appear on the monitor depending on the
camera settings and shooting conditions.
Standby mode
(Status screen)
Control panel
1/
F
250
5.6
Capture Mode
Status Screen
12800
With this camera, you can take pictures while looking through
the viewfinder or while viewing the image on the monitor.
When using the viewfinder, you can take pictures while
checking the status screen displayed on the monitor and the
viewfinder. When not using the viewfinder, you can take
pictures while viewing the Live View image displayed on the
monitor.
1234
1234
Shooting Info Display
selection screen
The camera is in “standby mode” when it is ready to shoot, such
as when the status screen or Live View image is displayed.
Press G in standby mode to display the “control panel” and
displayed in standby mode by pressing G while the control
panel is displayed. (p.18)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Screen
Live View
1
1
2
3
13
4
5
6
7
8
9
10 11
14
20
1 2 3 4 5 6 7 8 9 1011
1/
F
4000
5.6
12
12
15
16
16
102400
12
12
12
12
13
14
21 22 23
2000
17
18
19
20
17
18 19
24
30
9999
+1.0
2526 27
28
2526 27
29
9999
G1A1
EV
+1.7
15
0EV
1/2000 F2.8
1600
9999
1
2
3
4
Exposure Mode (p.48)
AE Lock (p.50)
Mirror Up (p.63)
Copyright Information
embedded (w p.R33)
HDR Capture (w p.R16)
Metering mode (p.47)
Focus Method (p.44)
17 Enable/Disable Controls
(w p.R43)
18 Number of shots during Multi-
exposure, Interval Shooting
or Interval Composite
19 180° Rotation Info (
25 Card slot number
26 File Format (w p.R15)
27 Image storage capacity
28 Flash Exposure
Compensation (p.65)
29 White Balance fine tuning
1/2000 F2.8
1600
9999
21 22 23 24 25 26 27 28
29
1
2
3
4
5
6
7
17 Electronic Level (vertical tilt)
w
p.R15)
5
6
7
8
9
19 180° Rotation Info (
w
p.R15)
White Balance (p.53)
HDR Capture (w p.R16)
Copyright Information
embedded (w p.R33)
Metering mode (p.47)
GPS positioning status
(w p.R18)
20 Operation guide
Number of shots during Multi-
exposure, Interval Shooting
or Interval Composite
Wireless LAN status (
GPS positioning status
(w p.R18)
w
p.R34)
22 Shutter speed
23 Aperture value
8
9
12 E-dial guide
13 Shutter speed
14 Aperture value
Movie SR (w p.R25)
25 EV bar scale
26 File Format (w p.R15)
27 Card slot number in use
28 Image storage capacity
29 Face detection frame (when
[Contrast AF] is set to [Face
Detection]) (p.46)
12 Wireless LAN status (
w
p.R34)
30 Operation guide
13 Temperature warning
14 Enable/Disable Controls
(w p.R43)
15 Histogram
16 Electronic Level (horizontal
Memo
• In [Live View] of the A3 menu, you can change the settings of the
items displayed on the monitor during Live View. (w p.R19)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
1
2
3
4
Function name
Setting
13 Memory Card Options
(w p.R15)
14 File Format (w p.R15)
15 JPEG Recorded Pixels and
Quality Level (w p.R15)/
movie recorded pixels
1
A mode
Card slot number
Number of recordable still
pictures/movie recordable
time
ISO AUTO Setting
(w p.R17)
Highlight Correction
(w p.R16)
Shadow Correction
(w p.R16)
ISO AUTO Setting
Adjustment Range
12345
12345
1
2
3
3
4
4
5
9
14
6
11
16
7
12
17
100-3200
(w p.R24)
8
13
18
10
15
5
16 High-ISO NR (w p.R17)
17 Slow Shutter Speed NR
(w p.R17)
Contrast AF (w p.R18)
19 Exposure Setting (w p.R24)
20 Focus Peaking (w p.R18)
21 Framerate (w p.R24)
22 Recording Sound Level
(w p.R24)
05/05/2014 10:30
24
25
6
7
8
9
When shooting with Live View
ISO AUTO Setting
Adjustment Range
12345
12345
1
2
3
3
4
4
Distortion Correction
(w p.R16)
Lateral Chromatic Aberration
Adjustment (w p.R16)
5
9
14
20
6
11
16
7
12
17
100-3200
8
13
18
10
15
05/05/2014 10:30
24
25
10 Peripheral Illumination
Correction (w p.R16)
11 Diffraction Correction
(w p.R16)
23 Movie SR (w p.R25)
24 Current date and time
25 Destination (w p.R28)
C mode
Exposure Setting
Program AE
1:23'45"
1:23'45"
1
2
3
3
4
4
12 HDR Capture (w p.R16)
19
13
23
6
15
7
21
18
22
20
12
Memo
• Items that can be selected vary depending on the current camera
setup.
05/05/2014 10:30
24
25
• If no operations are made within 1 minute while the control panel is
displayed, the camera will return to standby mode.
• You can change the display color of the status screen, control
panel and menu cursor in [Display Color] of [LCD Display] in the
D1 menu. (w p.R30)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting Info Display
Vertical Display
1
When the camera is held vertically, the status
screen and control panel are displayed in the
vertical position. To not display images in the
vertical position, set [Auto Screen Rotation] to
off in [LCD Display] of the D1 menu.
(w p.R30)
You can change the type of information displayed in standby
mode by pressing G while the control panel is displayed. Use
CD to select the type and press E.
1/
F
250
5.6
1600
When shooting with the viewfinder
Status
Screen
Displays the settings for shooting with the viewfinder. (p.16)
Displays the camera angle.
A bar scale indicating the
1234
1234
camera angle in the horizontal
direction appears at the bottom
of the screen, and a bar scale
Electronic indicating the camera angle in
Level
the vertical direction appears on
the right side. If the camera
angle cannot be detected, both
ends and the center of the bar
scales flash red.
Example:
Tilted 1.5° to the left (yellow)
No vertical tilt (green)
Disappears if no operations are made within 1 minute.
Display Off Nothing is displayed on the monitor.
The current latitude, longitude, altitude, direction, and
Coordinated Universal Time (UTC) are displayed. Turn the
camera off and on again to return to the status screen.
Available only when the optional GPS unit is attached to the
Electronic
Compass
When shooting with Live View
Standard Information The Live View image and the settings for
Display
Certain icons, such as those for the Exposure
Mode and Drive Mode, are not displayed.
No Information Display
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Playback Mode
• Press d to switch between the memory cards inserted in the two
slots, SD1 and SD2.
1
The captured image and shooting information are displayed in
single image display of the playback mode.
• The display selected in the Playback Info Display selection screen
appears in playback mode when the camera is turned off and on
again. If [Playback Info Display] is set to off in [Memory] of the A4
menu, the [Standard Information Display] always appears first
when the camera is turned on. (w p.R22)
Press G to change the type of information displayed in single
image display. Use CD to select the type and press E.
100-0001
100-0001
•
•
You can display the grid with [Grid Display] of the
You can set the camera so that the bright (overexposed) areas in the
image blink red with [Highlight Alert] of the 1 menu. ( p.R26)
B
1 menu. (
w
p.R26)
Standard Information Display
B
w
1/2000 F2.8
200
+0.3
1/2000 F2.8
200
+0.3
Single image display
(Standard Information Display)
Playback Info Display
selection screen
Captured image, file format, exposure
parameters, and operation guide indicators are
displayed.
Standard Information
Display
Detailed Information
Display
Detailed information on how and when the image
was taken is displayed (p.20).
Captured image and brightness histogram are
Histogram Display
Not available during movie playback.
Captured image and RGB histogram are
Not available during movie playback.
RGB Histogram
Display
No Information Display Only the captured image is displayed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Captured image
Rotation Information
(w p.R41)
26 Diffraction Correction
(w p.R16)
Detailed Information Display
28 File Format (w p.R15)
29 JPEG Recorded Pixels
(w p.R15)/movie recorded
pixels (w p.R24)
30 JPEG Quality (w p.R15)
31 Highlight Correction
(w p.R16)
32 Shadow Correction
(w p.R16)
Movie SR (w p.R25)
1
Still pictures
3
4
Digital Filter (p.79)/
HDR Capture (w p.R16)
Transferred via Wireless LAN
(w p.R34)
Card slot number in use
Folder number-File number
(w p.R31, w p.R33)
2
4
5
6
7
8
100-0001
3
9
1
37
38
10
15
11
12
+1.0
0
1/2000 F2.8
102400
13
14
18
19
0
0
0
0
0
0
5
20
16
17
+1.5
23 24 25 26 27
28 29 30 31 32 33
34
35 36
21
22
5000K
G1A1
6
7
8
55mm
05/05/2014 10:30
Movies
9
4
5
6
7
8
100-0001
3
9
1
37
38
11 Flash Exposure
39
10'10"
0
0
0
0
0
0
0
1/125 F8.0
1600
13
16
21
14
40
19
34 Lens focal length
17
0.0
35 Color Space (w p.R41)
36 Shooting date and time
38 Custom Image parameters
39 Length of time of the recorded
movie
Compensation (p.65)
22
5000K
G1A1
13 Shutter speed
14 Aperture value
22 White Balance fine tuning
23 Distortion Correction
(w p.R16)
55mm
05/05/2014 10:30
28 29 41 31 32 33
36
34
AB
Page 2
40 Volume
2
5
6
7
8
100-0001
123°
3
1
41 Framerate (w p.R24)
42 Altitude (w p.R18)
43 Lens direction (w p.R18)
44 Latitude (w p.R18)
45 Longitude (w p.R18)
46 Universal Coordinated Time
47 Information tampering
warning
42
43
0m
N
44
45
05/05/2014
10:00:00
36°45.410'
46
48
49
W140°02.000'
ABCDEFGGHIJKLMMNNOPQRSTTUVWXYZ
47
47
123456
ABCDEFGGHIJKLMMNNOPQRSTTUVWXYZ
123456
48 Photographer (w p.R33)
49 Copyright Holder (w p.R33)
24 Lateral Chromatic Aberration
Adjustment (w p.R16)
25 Peripheral Illumination
Correction (w p.R16)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Histogram Display/RGB Histogram Display
1
Use AB to switch between the Histogram Display and RGB
Histogram Display.
1
2
3 4
5
6
2
3 4
5
100-0001
100-0001
AB
6
12
13
14
1
1/2000 F2.8
200
1/2000 F2.8
200
+0.3
+0.3
7
8
9
10
11
7
8
9
10
11
Brightness histogram
RGB histogram
1
2
Histogram (Brightness)
Switch RGB histogram/
Brightness histogram
Protect setting
8
9
Shutter speed
Aperture value
10 Sensitivity
3
4
5
6
7
11 EV Compensation
12 Histogram (R)
13 Histogram (G)
14 Histogram (B)
Card slot number in use
Folder number-File number
File Format
21
Download from Www.Somanuals.com. All Manuals Search And Download.
12 SD1 slot
13 SD2 file format (w p.R15)
14 SD2 slot
18 Enable/Disable Controls
(w p.R43)
Viewfinder
1
21 ISO/ISO AUTO
2 3
16 Tethered shooting
EV bar scale
Shows the difference between the
1
1
proper and current exposure values in
L or N mode. If the value exceeds the range of the EV bar
scale, the “+” or “–” blinks.
1
1
Exposure Warning
When the proper exposure cannot be
obtained with the values set in G, H,
I, J, or K mode, the values
beyond the range of automatic adjustment blink.
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
21
Memo
1
2
3
4
AF frame
Spot metering frame (p.47)
AF point (p.45)
8
• The AF point appears in red (Superimpose AF Area) when the
shutter release button is pressed halfway. To turn off the red light
of the superimposed AF point, set [14. Superimpose AF Area] to
off in the E2 menu. (w p.R40)
• The item 16 appears when the camera is connected to a computer
using optional tethered shooting software.
Displays the difference
between the proper and
current exposure values in L
or N mode when [Electronic
Level] is set to on.
Flash:
EV bar scale:
Displays the exposure
compensation value or the
differencebetweenthe proper
and current exposure values
in L or N mode.
9
Appears when the flash is
available.
Blinks when the flash is
recommended or is being
charged.
Displays the camera angle
when [Electronic Level] is set
to on.
10 Flash Exposure
Compensation (p.65)
11 SD1 file format (w p.R15)
5
6
7
Focus indicator
Shutter speed
Aperture value
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
LCD Panel
• Press 8 to illuminate the LCD panel. (w p.R20)
• The item 13 appears when the camera is connected to a computer
using optional tethered shooting software.
1
1
2 3
4
5
6
7
8
9
10
11
12
Electronic Level
You can check whether the camera is tilted horizontally by
displaying the electronic level. The electronic level can be
displayed on the EV bar scale in the viewfinder and LCD panel,
and/or on the Live View screen.
13 14 15 16 17 18 19 20 21
Select whether to display the electronic level in [Electronic
Level] of the A3 menu. (w p.R19)
1
2
White Balance (p.53)
Enable/Disable Controls
(w p.R43)
Multi-exposure (p.58)
HDR Capture (w p.R16)
Drive Mode (p.56)
Shutter speed/Focusing area
Aperture value
15 Wireless LAN connection
(w p.R34)
16 GPS positioning status
(w p.R18)
18 JPEG Recorded Pixels/JPEG
Quality (w p.R15)
3
4
5
6
When level (at 0°)
20 SD1 file format (w p.R15)/
Remaining image storage
capacity (up to [1999])
21 SD2 file format (w p.R15)/
Remaining image storage
capacity (up to [1999])/USB
Connection mode
7
8
9
E-dials
EV bar scale/Electronic Level/
EV Compensation (p.50)
11 Copyright Information
embedded (w p.R33)
12 Flash Exposure
When tilted 4.5° to the left
(w p.R30)/Sensor Cleaning
(w p.R37)
PcS: MSC mode
PcP: PTP mode
Cln: During sensor cleaning
Compensation (p.65)
13 Tethered shooting
compensation value (p.50)
When held vertically and tilted 3° to the right
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Strap
Attaching a Lens
1 Pass the end of the strap
1 Make sure that the camera is turned off.
through the triangular ring.
2
2 Remove the body mount cap
(1) and lens mount cap (2).
Hold down the lens unlock button (3)
and remove the body mount cap.
3 Align the lens mount index
(red dots; 4) on the camera
and the lens, and turn the
lens clockwise.
2 Secure the end of the strap
on the inside of the clasp.
Do not press the lens unlock button at
this time.
To remove the lens
Turn the lens counterclockwise while
holding down the lens unlock button.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Remove the front lens cap
by pushing the top and
bottom portions as indicated
in the illustration.
2
Caution
• When attaching or removing the lens, choose an environment that
is relatively free of dirt and dust.
• Keep the body mount cap attached on the camera when a lens is
not attached.
• Be sure to attach the lens mount cap and lens cap to the lens after
removing it from the camera.
• Do not insert your fingers inside the lens mount of the camera or
touch the mirror.
• The camera body and lens mount incorporate lens information
contacts. Dirt, dust, or corrosion may damage the electrical
system. Please contact your nearest service center for
professional cleaning.
• We assume no responsibility nor liability for accidents, damages
and malfunctions resulting from the use of lenses made by other
manufacturers.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens Compatibility Chart
When using the D FA645 lens (for digital cameras), all of the functions of this camera are available. Lenses for our medium format
film cameras can also be used with this camera; however, the following restrictions apply. (x: Available #: Restricted ×: Not available)
Lens
A645
FA645
A645/FA645
A645/FA645
67
2
Accessories
With Rear converter A
and Auto extension tube A
With Helicoid
extension tube
With Adapter 645
for 67 lens
Lens only
Function
G/H/I/K mode
J/L mode
x
x
x
x
x
x
x
x
x
x
x
x
×
×
x
×
x
Program P-TTL auto flash
P-TTL auto flash
×
x
x
Automatic change of lighting angle when using
AF540FGZ, AF540FGZ II, AF500FTZ,
AF360FGZ, AF360FGZ II, or AF330FTZ
×
x
x
×
×
×
Display of aperture value in viewfinder at aperture position
9
#
x
×
×
×
×
v
×
x
x
x
x
×
x
x
×
Display of focus indicator in viewfinder in w mode
x
x
x
Metering mode switching
x
#
#
[Lens Correction] of the A1 menu
×
×
×
*1 This includes all types of helicoid extension tubes and accessories without information contacts.
*2 Stop-down metering
*3 Depending on the lens, the aperture ring value and the value displayed in the viewfinder may not match.
*4 The lens aperture value is displayed when using Auto extension tube A or Rear converter A645 2×.
The display varies when using Rear converter A645 1.4× with a lens other than Ak645 300mm F4 or FAk645 300mm F4.
[Displaying the lens aperture value as is indicated on the lens]
FA645 300mm F5.6, FA645 400mm F5.6, Ak645 600mm F5.6
[Displaying the maximum effective aperture value when combined with a lens]
A645 200mm F4, FA645 200mm F4, Ak645 300mm F4, FAk645 300mm F4, A645 macro 120mm F4, FA645 macro 120mm F4
[Displaying the aperture value with the aperture stopped down by two stops]
FA645 150mm F2.8
*5 Available only when the lens aperture value without accessories is F5.6 or wider, or when the maximum effective aperture value combined with accessories is F5.6
or wider.
*6 When using A645 macro 120mm F4, the function may become unreliable when the magnification ratio on the lens is set to between “1” (1:1) and “2” (1:2).
D (Spot) is always selected as the focusing area selection mode.
*7 The camera uses C (Center-weighted metering) even when A (Multi-segment metering) is selected.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
• Interval Shooting, Exposure Bracketing, and HDR Capture are
not available.
• Setting the shutter speed ring to LS when Exposure
Bracketing or HDR Capture is set cancels the setting.
• Setting the shutter speed ring to LS when Interval Shooting is
set exits Interval Shooting.
• In Multi-exposure mode, the shutter of the lens must be charged
manually for each shot.
• An external flash cannot be used even when connected to the
hot shoe. Be sure to use the sync terminal on the lens.
• An external flash cannot be synchronized even when connected
to the sync socket on the camera.
Using the Lens Shutter of the LS Lens
The PENTAX 645LS lenses have a built-in leaf shutter which
allows for high speed flash synchronization.
When using a leaf shutter lens, set the shutter speed ring on the
lens to LS.
Note that the following restrictions apply when using a leaf shutter
lens.
• The shutter of the lens cannot be used during Live View.
• The camera operates in L mode regardless of the exposure
mode setting on the camera.
• The difference from the proper exposure is not displayed.
• [LS] is displayed for the shutter speed.
2
• The flash mode setting is not applied to LS shooting.
• The proper exposure is not obtained even when M is pressed.
• EV Compensation is not available.
• Setting the shutter speed ring to LS when EV Compensation
is set cancels EV Compensation.
• AE Lock is not available.
• Setting the shutter speed ring to LS when AE Lock is set
cancels AE Lock.
• Continuous Shooting, Self-timer (2 sec.), Remote Control (3
sec. delay), and Remote Continuous Shooting of the drive
modes are not available.
• Setting the shutter speed ring to LS when Self-timer (2 sec.)
is set switches the shooting mode to Self-timer (12 sec.).
• Setting the shutter speed ring to LS when Remote Control (3
sec. delay) or Remote Continuous Shooting is set switches
the shooting mode to Remote Control (immediate release).
• Mirror Lock-Up Shooting is not available.
• Setting the shutter speed ring to LS when the mirror is raised
lowers the mirror.
• Optical Preview is not available.
• If the shutter of the lens is charged in advance, Digital Preview
can be used. (The same applies when using the Digital
Preview to preview the image with White Balance or Custom
Image.)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Using the Battery and
Charger
•
Do not use the battery charger D-BC90 to charge batteries other than
D-LI90. Charging other batteries may cause damage or heating.
• Replace the battery with a new one in the following cases:
• If the indicator lamp blinks or does not light after the battery is
inserted correctly
Use the battery D-LI90 and battery charger D-BC90 exclusively
developed for this camera.
2
•
If the battery starts to run down more quickly even after being
charged (the battery may have reached the end of its service life)
Charging the Battery
Memo
• The maximum charging time is approximately 390 minutes (it
depends on temperature and remaining battery power). Charge in
a location where the temperature is between 0°C and 40°C.
Indicator lamp
Lithium-ion battery
Inserting/Removing the Battery
Caution
Battery charger
AC plug cord
• Insert the battery correctly. If the battery is inserted incorrectly, it
may not be removed.
•
Wipe the electrodes of the battery with a soft dry cloth before inserting.
• Do not open the battery cover or remove the battery while the
power is on.
• Be careful as the camera or battery may become hot after the
camera is used continuously for a long period of time.
• Remove the battery when you will not use the camera for a long
time. The battery may leak and damage the camera if left installed
during prolonged periods of non-use. If the removed battery will not
be used for six months or longer, charge the battery for about 30
minutes before storing it, and after that, recharge the battery every
six to twelve months.
1 Connect the AC plug cord to the battery charger.
2 Plug the AC plug cord into the power outlet.
3 Face the A mark on the battery up, and insert it
into the battery charger.
The indicator lamp is lit while charging and turns off when the
battery is fully charged.
•
Store the battery in a location where the temperature will remain at
or below room temperature. Avoid locations with high temperatures.
• The date and time may be reset if you leave the battery out of the
camera for long periods of time. If this happens, set the current
date and time again. (w p.R28)
4 Remove the battery from the battery charger.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Level Indicator
1 Open the battery cover.
You can check the remaining battery level with the battery level
indicator on the monitor (when the monitor is in standby mode)
or on the LCD panel.
Lift the battery cover unlock knob, turn
it towards OPEN to unlock, and then
pull the cover open.
Monitor
I (Green)
LCD Panel
1
Battery Level
Battery is full.
2
J (Green)
K (Yellow)
L (Red)
2
Battery is one-third empty.
Battery is two-thirds empty.
Battery is almost empty.
The camera turns off after
Battery lock lever
2 Face the A mark on the
battery towards outside of
the camera, and insert the
battery until it locks into
place.
3
4 lit
M [Battery depleted] 4 blinks displaying the message. (The LCD
panel indicator continues to blink.)
To remove the battery
Push the battery lock lever in the
direction of 3.
Memo
• The battery level may not be displayed properly if the camera is
used at low temperatures or when performing Continuous
Shooting for a long time.
3 Close the battery cover.
• Battery performance temporarily decreases as the temperature
decreases. When using the camera in cold climates, have extra
batteries at hand and keep them warm in your pocket. Battery
performance will return to normal at room temperature.
• Have extra batteries ready when traveling overseas, or taking a lot
of pictures.
Turn the battery cover unlock knob
towards CLOSE to lock.
• Use the optional AC adapter kit when using the camera for a
• The battery level is not displayed when using the AC adapter.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AC Adapter
We recommend using the optional AC adapter kit K-AC132
when using the monitor for a long time or when connecting to
the camera to a computer or AV device.
2
1 Make sure that the camera is turned off, and open
the terminal cover.
2 Align the A marks on the DC
terminal of the AC adapter
and DC input terminal of the
camera, and connect.
3 Connect the AC adapter to the AC plug cord, and
plug the cord into the power outlet.
Caution
• Make sure that the camera is turned off before connecting or
disconnecting the AC adapter.
• Make sure that connections are secure between the terminals. The
memory card or data may be corrupted if the connection to the
power supply is lost while the card is being accessed.
• The battery in the camera does not charge when connected to the
AC adapter.
• Be sure to read the manual of the AC adapter kit before using the
AC adapter.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Insert the card all the way
into the memory card slot
with the memory card label
facing toward the monitor.
Inserting a Memory Card
The following memory cards can be used with this camera.
• SD Memory Card, SDHC Memory Card, and SDXC Memory
Card
H
S
U
P
O
T
T
C
E
J
E
Insert a memory card into one or both
of the SD1 and SD2 slots.
2
• Eye-Fi card
To use an Eye-Fi card or a Flucard,
insert the card in the SD2 slot.
• Flucard compatible with this camera
In this manual, these cards are referred to as memory cards.
Ideally you should use a high-speed, large-capacity memory
card.
To remove the memory card
Push the card in again.
H
S
U
P
O
T
T
Caution
C
E
J
E
•
A memory card must be formatted with this camera before use.
1 Make sure that the camera is turned off.
4 Close the card cover, and slide it in the opposite
2 Slide the card cover in the
direction of 1.
direction of 1.
Caution
• Be sure to fully close the card cover. The camera will not turn on if
the card cover is open.
• Do not turn off the power or remove the memory card while the
card access lamp is lit.
1
2
• Use a high-speed memory card when recording movies. If the write
speed cannot keep up with the recording speed, the writing may
stop during recording.
Memo
• For details on how the data is recorded when two memory cards
are inserted, refer to “Memory Card Options” (w p.R15).
• When using an Eye-Fi card or a Flucard, refer to “Wireless Memory
Card” (w p.R34).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
Initial Settings
1 Turn the main switch to
Language Setting
[ON].
2
The first time the camera is turned on after purchase, the
[Language/W] screen appears on the monitor. Follow the
procedure below to set the display language and the current
date and time.
The first time the camera is turned on
after purchase, the [Language/W]
screen appears.
1 Use ABCD to select the desired language and
Memo
press E.
• Always turn the camera off when not in use.
The [Initial Setting] screen appears in
the selected language.
Initial Setting
• The power will automatically turn off when you do not perform any
operations within a set period of time (Auto Power Off). To
reactivate the camera after it turns off automatically, turn it on
again, or press the shutter release button or 3.
English
New York
Text Size
Standard
Settings complete
• By default, the camera is set to power off automatically after 1
minute of inactivity. You can change the setting in [Auto Power Off]
of the D3 menu. (w p.R34)
Cancel
2 Press B.
The cursor moves to F (Hometown).
3 Press D.
The [F Hometown] screen appears.
Hometown
4 Use CD to select a city.
Use R to change the region.
New York
DST
Cancel
OK
5 Press B.
The cursor moves to [DST] (daylight saving time).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Use CD to select T or S and press E.
Date Adjustment
The camera returns to the [Initial Setting] screen.
Date Adjustment
Date Format
1 On the [Date Adjustment]
screen, press D and use
AB to select the date
format.
7 Press B.
mm/dd/yy
24h
The cursor moves to [Text Size].
Date
Time
01/01/2014
00:00
2
Initial Setting
8 Press D, use AB to select
Settings complete
English
[Standard] or [Large], and
Select [mm/dd/yy], [dd/mm/yy] or [yy/
mm/dd].
New York
MENU Cancel
OK OK
press E.
Selecting [Large] increases the text
size of the selected menu items.
Text Size
Standard
Large
Settings complete
2 Press D, and use AB to select 24h or 12h.
Cancel
OK
3 Press D.
Initial Setting
9 Press B to select [Settings
The frame returns to [Date Format].
English
complete] and press E.
New York
Text Size
4 Press B and then D.
The [Date Adjustment] screen
appears.
Standard
The frame moves to the month if the date format is set to [mm/dd/
yy].
Settings complete
Cancel
OK
5 Use AB to set the month,
Date Adjustment
Date Format
mm/dd/yy
24h
day and year.
Memo
Date
Time
01/01/2014
00:00
• You can select from 75 cities for the hometown and destination.
(w p.R28)
Settings complete
• In this manual, the menu screens hereafter are shown with [Text
Size] set to [Standard].
MENU Cancel
OK OK
• To change the Language, Hometown or Text Size settings, use the
D1 menu. (w p.R28)
6 Set the time in the same manner.
If you select [12h] in Step 2, the camera switches between am and
pm depending on the time.
7 Select [Settings complete]
Date Adjustment
Date Format
mm/dd/yy
24h
and press E.
Date
Time
05/05/2014
10:00
The status screen is displayed and the
camera switches to standby mode.
The seconds value is set to 0 seconds
when E is pressed.
Settings complete
Cancel
OK
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Formatting a Memory Card
D4
• Pressing F while setting the date and time cancels the settings
and switches the camera to standby mode. The [Initial Setting]
screen or the [Date Adjustment] screen will appear again the next
time the power is turned on.
A memory card must be formatted with this camera before use.
1 Press F.
1 2 3 4
Memory Card Options
Image Capture Settings
HDR Capture
2
• To change the date and time, use the D1 menu. (w p.R28)
The A1 menu appears.
Lens Correction
Exit
2 Turn Q or R to display D4 menu.
3 Use AB to select [Format]
1 2 3 4
Pixel Mapping
and press D.
Dust Alert
Dust Removal
Sensor Cleaning
Format
The [Format] screen appears.
Firmware Info/Options
Exit
4 Use AB to select the
memory card slot to format
and press D.
Format
SD1
SD2
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
5 Press A to select [Format]
Diopter Adjustment
All data on SD1 memory
and press E.
card will be deleted
-1
Formatting starts.
You can adjust the diopter from approximately -3.5 to +2.0 m .
Format
Cancel
When formatting is completed, the D4
menu reappears.
1 Turn the diopter adjustment
ring until the focusing
brackets on the focusing
screen are in focus while
looking through the
2
OK
6 Press F.
The camera returns to standby mode.
Caution
viewfinder.
• Do not remove the memory card while formatting. The card may be
damaged.
Turn the diopter adjustment ring
clockwise for a negative value and counterclockwise for a positive
value.
• Formatting deletes all data, both protected and unprotected.
Memo
Attaching the Large Eyecup
• When a memory card is formatted, the volume label “645Z” is
assigned to the card. When this camera is connected to a
computer, the memory card is recognized as a removable disk with
the name “645Z”.
Attach the Large Eyecup 645 O-EC107 as needed.
1 Slightly stretch the rim of the
large eyecup and attach it on
the camera, covering over
the standard eyecup.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The selected exposure mode is
displayed on the monitor (Guide
Display).
Testing Your Camera
Program
Automatic Exposure
yGuide Display settings (w p.R30)
Shooting
2
Take some test pictures to ensure that the camera is functioning
properly.
4 View the subject through the viewfinder and
press the shutter release button.
1 Turn the camera on.
The captured image appears on the monitor (Instant Review).
Available operations during Instant Review
2 Turn the Stills/Movie
L
Deletes the image.
switching dial to A.
R
H
Magnifies the image.
Saves the RAW image (only when a JPEG image
was taken and the data remains in the buffer).
Memo
• You can display the preview image on the monitor and check the
depth of field before shooting. (p.67)
• You can set the operation and display settings during Instant
Review in [Instant Review] of the A4 menu. (w p.R19)
• You can change the settings for the in-focus beep in [Sound
Effects] of the D1 menu. (w p.R29)
3 Turn the mode dial while
pressing the mode dial lock
button.
Mode dial
lock button
Dial indicator
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting with Live View
Reviewing Images
You can play back captured images.
1 Press 3.
The Live View image is displayed on
the monitor.
2
The camera enters playback mode
and the most recently captured image
(image with the highest file number) is
displayed on the monitor (single image
display).
2 Position the subject inside
the AF frame on the monitor
and press the shutter release
button halfway.
2 Review the captured image.
100-0001
1/2000 F2.8
1600
1234
AF frame
1/2000 F2.8
200
0.0
Available operations
Available operations during Live View
C/Q to the left
Displays the previous image.
E
Magnifies the image.
Use R to change the magnification (up to 16×).
Use ABCD to change the area to magnify.
Press M to return the display area to the center.
Press E to return to 1× image display.
D/Q to the right Displays the next image.
L
R to the right
Magnifies the image (up to 16×). (p.73)
Use ABCD to change the area to magnify.
Press M to return the display area to the center.
Press E to return to the entire image display.
K
Exits the Live View shooting.
Subsequent steps are the same as shooting with the viewfinder.
R to the left
d
Switches to the thumbnail display (p.74).
Switches between the SD1 card and SD2 card.
H
Saves the RAW image (only when a JPEG
image was taken and the data remains in the
buffer).
G
Changes the type of information displayed
(p.19).
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
How to Change Function
Settings
•
When Hv is displayed on the monitor, the JPEG image that
was just taken can also be saved in RAW format (Save RAW Data).
playback functions.
The camera functions and their settings can be selected and
changed by using the following ways.
2
• Use the provided software “Digital Camera Utility 5” to play back
Direct keys
Control panel
Menus
Press ABCD in standby mode.
Press G in standby mode.
(indicated with the v icon in this manual)
Press F.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Direct Keys
Using the Control Panel
G
WXYZ
You can use the direct keys in standby mode to directly set
functions.
You can set frequently used shooting functions.
The following explains how to set [Slow Shutter Speed NR] as
an example.
2
A
B
C
D
Drive Mode
Flash Mode
1 Press G in standby mode.
White Balance
Custom Image
The control panel appears.
The following explains how to set the flash mode as an
example.
2 Use ABCD to select the
ISO AUTO Setting
Adjustment Range
12345
12345
1 Press B in standby mode.
item you want to change the
setting for.
100-3200
The Flash Mode setting screen
appears.
Only items which can be set can be
selected.
05/05/2014 10:30
3 Use Q or R to change
Slow Shutter Speed NR
Auto
12345
12345
settings.
100-3200
2 Use CD to select a flash
Flash On
Press E to display the detailed setting
screen for the selected item, and press
E again to confirm the setting change.
mode.
0.0
05/05/2014 10:30
Cancel
OK
4 Press F.
The camera returns to standby mode.
3 Press E.
The camera returns to standby mode.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use AB to select an item
1 2 3 4
Using the Menus
F
D-Range Settings
ISO AUTO Setting
High-ISO NR
and press E.
This section explains how to use the menus: [A Rec. Mode],
[C Movie], [B Playback], [D Set-up] and [E Custom Setting].
The following explains how to set [Slow Shutter Speed NR] in
the A2 menu as an example.
Slow Shutter Speed NR
Program Line
GPS
Next, set other items.
Press F to exit the menu and return
to the screen that was displayed before
selecting a menu item.
2
Cancel
OK
1 Press F in standby mode.
Caution
The A1 menu appears on the monitor.
• Your settings may not be saved if the camera is turned off
improperly (such as by removing the battery while the camera is
on).
Memo
• Press F to display the first tab of the proper menu for the
camera conditions at that time. To display the menu tab last
selected first, set in [23. Save Menu Location] of the E4 menu.
(w p.R41)
• Settings are returned to their default values with [Reset] of the D3
menu. (w p.R35) To reset all the settings of the Custom Setting
menu (E1-5) to the defaults, use [Reset Custom Functions] of the
E5 menu. (w p.R43)
2 Press D or turn R to the
1 2 3 4
Memory Card Options
Image Capture Settings
HDR Capture
right.
Lens Correction
Each time D is pressed, the menu will
change in the following sequence: A2,
A3, A4, C1 ...A1.
When Q is turned to the right, the
category will change in the following sequence: A1, C1, B1,
Exit
• Refer to “Menu Reference” for details on each menu.
D1, E1.
•
•
•
•
•
A Rec. Mode Menu w p.R15
C Movie Menu w p.R24
B Playback Menu w p.R26
D Set-up Menu w p.R28
3 Use AB to select an item
1 2 3 4
D-Range Settings
ISO AUTO Setting
High-ISO NR
and press D.
Slow Shutter Speed NR
Program Line
GPS
Available settings are displayed.
Any detailed settings are displayed in
the submenu.
E Custom Setting Menu w p.R39
Exit
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Focusing
Setting the AF Mode when Shooting with
the Viewfinder
Selecting the Focus Mode
1 Use the AF mode switching
dial on the camera to select
either x or E.
1 Switch the focus modes
between AF and MF on the
lens.
3
The autofocus method for shooting with the viewfinder differ
from that for shooting with Live View.
TTL phase-matching autofocus:
Select from x or y.
Shooting with the
Set the focusing area using the AF points. (p.45)
viewfinder
Faster autofocus performance than contrast detection
x
Locks the focus at the position where the subject
AF is possible.
Autofocus/
is in focus.
Single mode
ShootingwithLive Contrast detection AF:
View
Face Detection and Tracking are available. (p.46)
Continuously adjusts the focus to keep the subject
in focus. The shutter can be released even if the
subject is not in focus.
E (y)
Autofocus/
Memo
The camera automatically tracks the subject if the
Continuous mode
• You can use the I button to focus on
the subject. The I button operation
can be set in [Button Customization] of
the A4 menu. (w p.R20)
• You can adjust the AF focus position
with [24. AF Fine Adjustment] in the
E4 menu. (w p.R42)
subject is determined to be a moving object during
focusing.
Memo
• The settings for AF operations can be set in the E3 menu.
(w p.R40)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Sets the focusing area to the user selected point from
27 points. When the subject happens to move out of
the selected focusing area after being focused, 26
peripheral points are used as back-up points.
Not available in x mode.
Selecting the Focusing Area (AF Point)
Expanded
Area AF (L)
H
1 Turn R while pressing
6.
Sets the focusing area to the center of the 27
points.
D Spot
Proceed to Step 2 when a mode other than J or D is selected.
3
2 Select the desired AF point.
1/
F
250
5.6
The AF point appears in the viewfinder.
3200
1234
1234
The AF area appears on the status
1/
screen and LCD panel.
F
250
5.6
Available operations
3200
ABCD
Changes the AF point.
Returns the AF point to the center.
E
c
1234
1234
Switches the function of the arrow keys (ABCD) to
that for Change AF Point or the direct key operation.
Auto (27 AF Out of the 27 AF points, the camera automatically
J
Points)
selects the optimum focusing area. (Default setting)
Memo
Out of the selected 9 AF points, the camera
• When the AF point can be changed, Q appears in the viewfinder.
• You can also set the AF point with [AF Active Area] on the control
panel.
I Zone Select
automatically selects the optimum focusing area.
Sets the focusing area to the user selected point
from 27 points.
E Select
• You will hear a beep when the function of ABCD is switched by
pressing c. You can change the setting with [Sound Effects] in the
D1 menu. (w p.R29)
• To enable changing the AF point (disable the direct key operation)
any time the focusing area selection mode is set to I, E, F,
G, or H, set in [26. 4-way Controller Options] of the E4 menu.
(w p.R42)
Sets the focusing area to the user selected point from
27 points. When the subject happens to move out of
the selected focusing area after being focused, 8
peripheral points are used as back-up points.
Not available in x mode.
Expanded
F
Area AF (S)
Sets the focusing area to the user selected point from
27 points. When the subject happens to move out of
the selected focusing area after being focused, 24
peripheral points are used as back-up points.
Not available in x mode.
Expanded
G
• Some AF points cannot be selected depending on the lens or
Area AF (M)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press c.
Setting the AF Mode during Live View
The screen to set the AF area is displayed.
You can select an autofocus mode when shooting with Live View.
3 Select the AF area.
1 Turn R while pressing
Use the frame that appears on the
monitor to change the position and size
of the AF area.
6.
OK
3
Available operations
ABCD
R
Changes the position of the AF area.
Increases/reduces the size of the AF area (when g
is selected).
M
Returns the AF area to the center.
The screen for selecting an autofocus
mode appears.
4 Press E.
Face Detection
The AF area is set.
Caution
1/2000 F2.8
1600
1234
• When f is selected, the focus lock operation (composition
adjustment with the half press of the shutter release button) does
not work.
Detects and tracks faces of people. (Default setting)
The main face detection frame for AF and AE is
displayed in yellow.
Face
Detection
e
f
Tracks the subject in focus.
Tracking The shutter can be released even if the subject is not
Memo
• You can also select an autofocus mode for Live View in [Contrast
AF] of [Live View] in the A3 menu or [Contrast AF] in the control
panel. (w p.R18)
• When [Focus Peaking] of [Live View] in the A3 menu or [Focus
Peaking] in the control panel is set to on, the outline of the subject
in focus is emphasized and makes it easier to check the focus.
(w p.R18)
in focus.
Sets the focusing area to the desired area.
The sensor is divided into 35 areas (7 horizontal by 5
AF Points vertical), and you can select a wider or narrower focusing
Multiple
g
area by using 1, 9, 15, or 21 of those 35 available areas.
h
i
Select
Spot
Sets the focusing area by the number of pixels.
Sets the focusing area to a limited area at the center.
Proceed to Step 2 if g or h is selected.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Exposure Setting
Setting the Sensitivity
You can set the sensitivity to [AUTO] or a value in the range
equivalent to ISO 100 to 204800 (ISO 100 to 3200 for C
mode).
Selecting the Metering Mode
1 Turn the metering mode
1 Turn R while pressing
switching dial.
N.
3
The set metering mode is displayed on
the status screen, Live View screen
and in the viewfinder.
Press M while pressing N to switch
to [AUTO].
Meters the brightness in multiple different zones of
Multi-
the sensor.
A
segment In backlit locations, this mode automatically adjusts
exposure.
Meters the brightness with an emphasis on the
center of the sensor.
Memo
Center-
• Set the range of automatic sensitivity adjustment with [ISO AUTO
Setting] in the A2 menu or on the control panel. (w p.R17)
• You can set the sensitivity in increments of 1 EV or in accordance
with the EV Steps setting for exposure. Set from [2. Sensitivity
Steps] of the E1 menu. (w p.R39)
B
C
The sensitivity increases at the center and no
weighted
automatic adjustment is performed even in backlit
conditions.
Meters the brightness only within a limited area at the
center of the sensor.
Spot
Useful when the subject is small.
• You can reduce noise at high sensitivity with [High-ISO NR] in the
A2 menu or on the control panel. (w p.R17)
• The framerate for Continuous Shooting may slow down when the
sensitivity is high.
Memo
• You can link the metering point and the AF point. Set in [5. Link AE
and AF Point] of the E1 menu. (w p.R39)
Exposure Metering Timer
Set the exposure metering time with [3. Meter Operating Time] of
the E1 menu. (w p.R39)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Exposure Mode
The following are the available exposure modes.
(x: Available ×: Not available)
EV
ChangeShutter
Speed
Change
Aperture Value
Change
Sensitivity
Exposure Mode
Function
Compensation
Automatically sets the shutter speed and aperture value
according to the program line.
You can use Q or R to switch between shutter priority and
aperture priority.
G
Program Automatic
Exposure
x
x
x
x
3
H
Other than
AUTO
Sensitivity Priority
Automatic Exposure
You can set the desired sensitivity.
You can set the desired shutter speed.
You can set the desired aperture value.
x
x
x
×
x
×
×
×
I
Shutter Priority
Automatic Exposure
x
x
J
Aperture Priority
x
Automatic Exposure
K
Shutter & Aperture
Priority Automatic
Exposure
Automatically sets the sensitivity according to the set shutter
speed and aperture value.
x
x
x
AUTO only
L
Other than
AUTO
You can set exposure parameters.
x
×
x
×
x
x
x
–
Manual Exposure
M
Other than
AUTO
Bulb shooting
Bulb Exposure
N
The shutter speed is locked at 1/125 seconds. Use this when
Other than
AUTO
x
–
×
Flash X-sync Speed using a flash that does not automatically set the sync speed.
O/P/Q
User settings
Lets you capture images with the previously-saved exposure
mode and settings.
–
–
Memo
• Set the program line in [Program Line] of the A2 menu. (w p.R18)
• The sync speed of N can be changed in [25. Flash Sync Speed] of the E4 menu. (w p.R42)
• Save the settings to O, P, or Q in [Save USER Mode] of the A4 menu. (w p.R22)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
During Live View, D appears for the
value that can be changed.
1 Turn the mode dial while
pressing the mode dial lock
button.
1/30
F4.5
100
1234
Memo
• The settings for exposure can be specified in increments of 1/3 EV
steps. In [1. EV Steps] of the E1 menu, you can change the
adjustment steps to 1/2 EV steps. (w p.R39)
• A proper exposure may not be obtained with the selected shutter
speed and aperture value when the sensitivity is set to a certain
sensitivity value.
3
2 Use Q or R to change
settings.
• In L or N mode, the difference from the proper exposure is
displayed on the EV bar scale while the exposure is adjusted.
• In M mode, the drive mode cannot be set to Continuous Shooting,
Multi-exposure+Continuous, Interval Shooting, Interval
Composite, or Exposure Bracketing.
• For each exposure mode, you can set the camera operation for
when Q or R is turned or M is pressed. Set in [E-Dial
Programming] of the A4 menu. (w p.R20)
Q and/or R appear on the status
screen next to the setting that is being
changed.
1/
F
30
4.5
100
1234
1234
The value that can be changed is
underlined in the viewfinder.
Q and/or R appear on the LCD
panel for the value that can be
changed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
EV Compensation
AE Lock
The compensation value can be set between -5 and +5 EV (-2
and +2 EV in C mode).
AE Lock is the function that locks the exposure prior to taking
the picture.
1 Turn R while pressing J.
1 Press H.
e is displayed on the status screen,
Live View screen, LCD panel and in
the viewfinder during compensation.
Press M while pressing J to return to
0.0.
O is displayed on the status screen,
Live View screen, LCD panel and in
the viewfinder when AE Lock is set.
3
Memo
• The exposure remains in memory for twice the amount of the
exposure metering timer, even after you take your finger off H.
• You will hear a beep when H is pressed. You can change the
setting with [Sound Effects] in the D1 menu. (w p.R29)
• When AE Lock is set in L mode, you can change the shutter
speed and aperture value while maintaining the exposure value.
• AE Lock is not available in M or N mode.
• When any of the following operations are performed, AE Lock is
canceled.
• When H is pressed again
• When 3, F, or G is pressed
• When the mode dial is turned
• When the lens is changed
• When the aperture ring of the lens with an aperture 9 position
is set to 9 or is switched to a position other than 9
• When using a zoom lens whose maximum aperture varies
depending on the focal length, the shutter speed and aperture
value change depending on the zooming position while AE Lock is
engaged. However, the exposure value does not change and a
picture is taken at the brightness level when AE Lock is set.
• Exposure can be locked when focus is locked. Set in [4. AE-L with
AF Locked] of the E1 menu. (w p.R39)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press a.
Movie Recording
Movie recording starts.
In the upper left area of the monitor,
“REC” blinks and the size of the file
being recorded is displayed.
1 Turn the Stills/Movie
switching dial to C.
4 Press a again.
3
Movie recording stops.
Caution
• When recording a movie with sound, the camera operation sounds
are also recorded.
• If the internal temperature of the camera becomes high during
recording, the recording may be terminated.
Memo
Live View is displayed.
Sound
• Recording can also be started or stopped by pressing the shutter
release button fully.
• You can change the movie settings in the C1 menu or from the
control panel. (w p.R24) When [Exposure Setting] is set to n,
p or o, you can set the exposure before shooting.
• You can record a movie continuously up to 4 GB or 25 minutes.
When the memory card is full, recording stops.
10'30"
Recordable Time
2 Focus on the subject.
In v mode, press the shutter release button halfway.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back Movies
Microphone terminal
Using an External
Microphone
1 Display the movie to play
back in single image display
of the playback mode.
You can connect a commercially
available stereo microphone to the
microphone terminal on the camera.
Using an external microphone can
also help to reduce the possibility of
recording camera operation sounds.
The following specifications are
100-0001
10'00"
3
Available operations
recommended for external microphones.
A
Plays back/pauses a movie.
Plug
Stereo mini plug (ϕ3.5 mm)
D
Forwards a frame (when paused).
Fast-forwards playback.
Format
Stereo electret condenser
Press and hold D
Plug-in Power Method (operating voltage of 2.0 V or
lower)
Power
C
Reverses a frame (when paused).
Fast-reverses playback.
Press and hold C
Impedance 2.2 kΩ
B
Stops playback.
If the external microphone is disconnected during recording, no
sound will be recorded.
R
Adjusts the volume (21 levels).
Saves the displayed frame as a JPEG file (when
paused).
H
Memo
• In [Movie Edit] of the playback mode palette, movies can be
divided or selected frames can be deleted. (p.81)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Press C in standby mode.
White Balance
The White Balance setting screen
appears.
The following settings are available.
Setting
Color Temperature
g
Auto White Balance (default
setting)
Multi Auto White Balance
Approx. 4,000 to
8,000K
g
u
2 Select the White Balance.
Auto White Balance
3
h
i
j
Daylight
Shade
Cloudy
Approx. 5,000K
Approx. 8,000K
Approx. 6,000K
For g, k, o and p, press B and
then use CD to select the White
Balance.
q
r
s
t
Fluorescent - Daylight Color
Fluorescent - Daylight White
Fluorescent - Cool White
Fluorescent - Warm White
Approx. 5,700K
Approx. 4,700K
Approx. 4,200K
Approx. 3,500K
Check
Cancel
OK
WB
k
Available operations when shooting with the viewfinder
Main switch to U
Uses Digital Preview to preview the background
image with the white balance setting applied.
l
m
Tungsten
Approx. 2,850K
Flash
Approx. 5,400K
H
Saves the preview image (only when the image
can be saved).
n
o
Color Temperature Enhancement
Manual White Balance 1 to 3
–
–
Proceed to Step 5 if you do not need to fine-tune the white balance.
Approx. 2,500 to
10,000K
p
Color Temperature 1 to 3
3 Press G.
The fine-tuning setting screen appears.
Memo
G3
A2
• When u is set, even if various light sources are present at the
shooting location, the camera automatically adjusts the white
balance according to the light source of each area. (Not available
in C mode.)
Check
Cancel
OK
0
Available operations
AB
CD
M
Adjust: Green-Magenta
Adjust: Blue-Amber
Resets the adjustment value to the default setting.
4 Press E.
The screen of Step 2 reappears.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press E.
Saving the White Balance Settings of a
Captured Image
The camera returns to standby mode.
You can copy the white balance settings of an image captured
with this camera and save them as Manual White Balance.
Memo
• The settings for the white balance can be set in the E2 menu.
(w p.R40)
1
In single image display of the playback mode,
display the image with the white balance settings
3
you want to copy and then press
The playback mode palette appears.
B.
Manual White Balance
You can save up to three manual white balance settings.
2 Select o (Save as Manual WB) and press E.
The save confirmation screen appears.
2 Select from o1 to o3.
Manual White Balance
3 Select the “Manual” number
100-0001
Saves this image's White Balance
1, 2 or 3 to save the settings.
settings as a custom selection
Use Q to select a different image.
Save as Manual
Save as Manual
Save as Manual
1
2
3
Adjust
Check
Cancel
OK
WB
Cancel
OK
3 Under the light you wish to measure the white
4 Press E.
balance of, select a white area as the subject, and
press the shutter release button fully.
The white balance settings of the selected image is saved as
Manual White Balance and the camera switches to standby mode.
The captured image is displayed.
Caution
[The operation could not be completed correctly] appears when
measuring is unsuccessful. Press E to remeasure the white
balance.
• The fine-tuned white balance value used when shooting is not
saved.
4 Use ABCD to specify the measuring range.
5 Press E.
The White Balance setting screen reappears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Temperature
You can save up to three color temperature settings. (The
default setting is [5000K].)
2 Select from p1 to p3.
3
3 Press G.
4 Adjust the color
temperature.
Set the color temperature value within
0
0
the range from 2500K to 10000K.
Check
Cancel
OK
0
Available operations
Q
100 Kelvin units
1000 Kelvin units
R
ABCD
Fine-tunes the color temperature.
5 Press E.
The White Balance setting screen reappears.
Memo
• Select [Mired] in [13. Color Temperature Steps] of the E2 menu to
set the color temperature in mired units. The color temperature can
be changed in 20 mired units with Q, and 100 mired units with
R. However, figures are converted to and displayed in Kelvin.
(w p.R40)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Drive Mode
• There are restrictions on some drive modes when used in
combination with some other functions. (w p.R44)
You can choose from the following drive modes.
Single Frame Shooting
Normal capture mode
(L)
W
Continuous Shooting
Continuously takes pictures while the shutter
Continuous Shooting release button is kept pressed.
1 Press A in standby mode.
(Z/b)
The number of pictures that can be taken
3
continuously varies according to the shutter speed.
The Drive Mode setting screen
appears.
Self-timer
Releases the shutter about 12 seconds or 2
(O/P)
seconds after the shutter release button is pressed.
Enables shooting with remote control.
Select from [Remote Control], [Remote Control (3
sec. delay)] or [Remote Continuous Shooting].
Remote Control
(Q/R/S)
Creates a composite picture by taking multiple
images and merging them into a single image.
Select from [Multi-exposure], [Multi-exposure
+Continuous], [Self-timer+Multi-exposure] or
[Remote Control+Multi-exposure].
2 Select Z and press B.
Continuous Shooting (H)
Multi-exposure
(V/2/W/X)
Interval Shooting
(Y)
Takes pictures at a set interval from a set time.
Cancel
OK
Takes still images at a set interval and merges
them into a single image.
Star and moon trails can be captured in one image.
3 Select Z or b and press E.
Interval Composite
(3)
The camera returns to standby mode.
Interval Movie
Record
(Y)
Takes still images at a set interval from a set time
and saves them as a single movie file.
Available only in C mode.
Memo
• When the AF mode is set to x, the focus position is locked in
the first frame.
Memo
• The framerate may slow down when the sensitivity is high.
•
Only
4
(Remote Control Off),
Q
or
Y
can be selected in
C
mode.
• The Drive Mode setting is saved even after the power is turned off.
If [Drive Mode] is set to off in [Memory] of the A4 menu, the setting
returns to Single Frame Shooting when the power is turned off.
(w p.R22)
• When the drive mode that employs the self-timer or remote control
is selected, exposure may be affected by the light entering through
56
Download from Www.Somanuals.com. All Manuals Search And Download.
W
W
Self-timer
Remote Control
1 Press A in standby mode.
1 Press A in standby mode.
The Drive Mode setting screen
appears.
The Drive Mode setting screen
appears.
3
2 Select O and press B.
2 Select Q and press B.
Self-timer (12 sec.)
Remote Control
Cancel
OK
Cancel
OK
3 Select O or P and press E.
3 Select Q, R, or S and press E.
The camera returns to standby mode.
The self-timer lamp blinks.
The camera returns to standby mode.
4 Press the shutter release button halfway, then
4 Press the shutter release button halfway.
5 Point the remote control unit towards the remote
control receiver on the front or back of the
camera, and press the shutter release button on
the remote control unit.
fully.
The self-timer lamp blinks.
The shutter will be released about 12 seconds or 2 seconds.
Memo
• The maximum operating distance of the remote control unit is
approx. 4 m from the front of the camera and approx. 2 m from the
back of the camera.
• To adjust focus with remote control, set in [19. AF with Remote
Control] of the E3 menu. (w p.R41)
• When using the Remote Control Waterproof O-RC1, the autofocus
system can be operated with the q button. The r button cannot
be used.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press the shutter release button to start shooting.
W
Multi-exposure
Instant Review is displayed.
Available operations during Instant Review
1 Press A in standby mode.
L
Discards pictures taken up to that point and takes
pictures again from the first picture.
The Drive Mode setting screen
appears.
F
Saves pictures taken up to that point and displays
the A menu.
3
After the set number of pictures are taken, the camera returns to
normal capture mode.
2 Select V and press B.
Caution
3 Select V, 2, W or X, and
Multi-expposure
• Multi-exposure cannot be used with [HDR Capture] in the A1
menu at the same time. The mode set last is used.
• [Lens Correction] in the A1 menu is not available when Multi-
exposure is set.
press B.
Composite Mode
Number of Shots
0002times
Cancel
OK
4 Select [Composite Mode].
Creates a composite image with the average
exposure.
5
6
7
Average
Additive
Bright
Creates a composite image with the cumulatively
added exposure.
Creates a composite image that combines only bright
parts.
5 Specify [Number of Shots].
Select from 2 to 2000 shots.
6 Press E.
The camera returns to standby mode.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
W
Interval Shooting
• A new folder is created when Interval Shooting is performed, and
the captured images are saved there. When shooting in a different
drive mode after performing Interval Shooting, a new folder will be
created again.
1 Press A in standby mode.
The Drive Mode setting screen
appears.
• The shortest interval time that can be set for [Interval] is 30
seconds when [HDR Capture] is set in the A1 menu.
3
2 Select Y and press B.
3 Set the shooting conditions.
Interval Shooting
Interval
00:00'02"
N00ow02times
Number of Shots
Start Interval
Cancel
OK
Interval
Select from 2 seconds to 24 hours.
Number of Shots Select from 2 to 2000 shots.
Select whether to take the first picture now or at a
set time.
When [Set Time] is selected, set the time at which
to start shooting in [Start Time].
Start Interval
4 Press E to finish setting.
The camera returns to standby mode.
5 Press the shutter release button to start shooting.
When [Start Interval] is set to [Now], the first picture is taken. When
set to [Set Time], shooting starts at the set time.
To cancel shooting, press F in standby mode.
After the set number of pictures are taken, the camera returns to
normal capture mode.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press the shutter release button to start shooting.
W
Interval Composite
When [Start Interval] is set to [Now], the first picture is taken. When
set to [Set Time], shooting starts at the set time.
To cancel shooting, press F in standby mode.
After the set number of pictures are taken, the camera returns to
normal capture mode.
1 Press A in standby mode.
The Drive Mode setting screen
appears.
Memo
3
• When [Save Process] is set to T, a new folder is created and the
composite image is saved there. When shooting in a different drive
mode after performing Interval Composite, a new folder will be
created again.
2 Select 3 and press B.
3 Set the shooting conditions.
Interval Composite
• Mount the camera on a tripod during Interval Composite.
Composite Mode
Save Process
Interval
00:00'02"
N00ow02 times
Number of Shots
Start Interval
Cancel
OK
Select from [Average], [Additive] or [Bright].
Composite Mode
Select T to save the image in the process of
composition.
Save Process
Interval
Select from 2 seconds to 24 hours.
Number of Shots Select from 2 to 2000 shots.
Select whether to take the first picture now or at a
set time.
When [Set Time] is selected, set the time at which
to start shooting in [Start Time].
Start Interval
4 Press E to finish setting.
The camera returns to standby mode.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Set the shooting conditions.
Interval Movie Record
W
Interval Movie Record
Recorded Pixels
In C mode, you can use [Interval Movie Record] to take still
pictures at a set interval from a set time and save them as a
single movie file (Motion JPEG, file extension: .AVI).
Interval
2sec.
Recording Time
Start Interval
N00ow:000'14"
Cancel
OK
1 Turn the Stills/Movie
switching dial to C and
press A.
Recorded Pixels Select from z, u, or t.
Select from 2 sec., 5 sec., 10 sec., 20 sec., 30
sec., 1min., 5 min., 10 min., 30 min., or 1hr.
3
Interval
Set the time from the start to the end of recording.
Select from 14 seconds to 99 hours. The time that
can be set varies depending on the [Interval]
setting.
The Drive Mode setting screen
appears.
Recording Time
Select whether to take the first picture now or at a
set time.
When [Set Time] is selected, set the time at which
to start shooting in [Start Time].
Start Interval
4 Press E to finish setting.
The camera returns to standby mode.
5 Press the shutter release button to start shooting.
When [Start Interval] is set to [Now], the first picture is taken. When
set to [Set Time], shooting starts at the set time.
Instant Review is displayed, and then the monitor turns off.
After the set number of pictures are taken, the camera returns to
standby mode.
2 Select Y and press B.
Memo
• The shortest interval time that can be set for [Interval] is 30
seconds when [HDR Capture] is set in the A1 menu.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Exposure Bracketing
You can use Exposure Bracketing to take 2 (standard exposure
and underexposure, or standard exposure and overexposure),
3 or 5 images with different exposure levels.
2 images (underexposed) at 0.3 EV
5 images at 1.0 EV
This function can be used with Continuous Shooting, Self-timer,
or Remote Control set by pressing A.
3 Press the shutter release button fully.
Select [OFF] in Step 1 to finish shooting with Exposure Bracketing.
3
1 Turn Q while pressing 5
to set the number of shots.
Check the setting on the LCD panel.
Memo
• Set the auto bracketing order with [8. Bracketing Order] in the E2
menu. (w p.R40)
• Set the EV step interval with [1. EV Steps] in the E1 menu.
(w p.R39)
• Set [9. One-Push Bracketing] in the E2 menu to shoot all frames
with one press of the shutter release button. (w p.R40)
• If you take your finger off the shutter release button before shooting
of the set number of images is completed, the next bracket setting
will remain effective for twice the amount of the exposure metering
time.
Right (clockwise)
Left (counterclockwise) OFF→-2→2→5→3→OFF
OFF→3→5→2→-2→OFF
• You can combine Exposure Bracketing with the P-TTL auto flash
to change the flash output continuously. Confirm that the flash unit
is fully charged before shooting each frame.
2 Turn R while pressing 5 to set the bracket
value.
Caution
• This function is not available in M mode.
• This function cannot be used with Multi-exposure, Interval
Shooting, or Interval Composite. The function set last is used.
EV Steps
1/3 EV
Compensation Value
±0.3, ±0.7, ±1.0, ±1.3, ±1.7, ±2.0
±0.5, ±1.0, ±1.5, ±2.0
1/2 EV
Press M while pressing 5 to return to [OFF] and [--].
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Mirror Lock-up Shooting
• Mirror Lock-up Shooting is not available when shooting with Live
View. When the mirror is raised, the Live View image is not
displayed even if K is pressed.
• Turning the mode dial or adjusting the lens aperture ring when the
mirror is raised lowers the mirror.
This raises the mirror.
This function can be used with another drive mode set by
pressing A.
• The image preview is not available when the mirror is raised.
• The mirror is not raised during Interval Shooting or Interval
Composite even when the Mirror Up dial is set to the “UP” position.
1 Turn the Mirror Up dial.
The camera is ready to raise the
mirror.
3
Shake Reduction
The Shake Reduction function is available when a lens with the SR
system is used in A mode. Refer to the SR-supported lens
manual for details on using the function. The Shake Reduction
function is automatically turned off when Self-timer, Remote
Control, Interval Movie Record, or Mirror Lock-up Shooting is set.
In C mode, the Shake Reduction function can be activated from
[Movie SR] of the C1 menu. (w p.R25)
M
.U
P
2 Press the shutter release button fully.
The mirror is raised.
3 Press the shutter release button fully again.
The mirror returns to its original position after an image is taken.
To exit Mirror Lock-up Shooting, return the Mirror Up dial to its
original position.
Memo
• The mirror automatically returns to its original position if 5 minutes
elapse after the mirror is raised or the Auto Power Off function is
activated. Depending on the shooting conditions, the mirror may
return to its original position before 5 minutes elapse.
• To disable the Mirror Up dial operation, set in [27. Mirror Up
Operation] of the E4 menu. (w p.R42)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash Mode
Using a Sync Cord
Sync socket
You can connect a sync cord to the
sync socket on the camera.
Attaching a Flash
1 Remove the hot shoe cover
of the camera.
3
Sync socket 2P cap
Memo
2 Attach the flash and turn on the camera.
• The flash connected to the sync socket can be discharged in
Modeling Flash or Test Flash mode by pressing 8. The setting can
be changed with [Illumination Button] in [Button Customization] of
the A4 menu. (w p.R20)
Caution
• Do not use high-voltage or high-current external flashes. They may
cause the camera to malfunction.
• A flash with reversed polarity (the center of the hot shoe or sync
plug has a negative symbol) cannot be used, as this may damage
the camera or flash.
Caution
• The contact of the sync socket is not dust-proof or water-resistant.
Attach the provided Sync socket 2P cap when not in use.
• Linked functions do not work.
• To prevent vignetting caused by Trailing Curtain Sync from
occurring, it is recommended to take a test shot using a shutter
speed one stop slower than the flash sync speed.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
The compensation value varies depending on the setting of [1. EV
X
Steps] (w p.R39) in the E1 menu.
Setting the Flash Mode
EV Steps
1/3 EV
Compensation Value
The following flash modes are available. The flash modes that
can be set vary depending on the exposure mode.
-2.0, -1.7, -1.3, -1.0, -0.7, -0.3, 0.0, +0.3, +0.7,
+1.0
Flash Mode
Flash On
Available Exposure Modes
1/2 EV
-2.0, -1.5, -1.0, -0.5, 0.0, +0.5, +1.0
C
Press M to reset the value to 0.0.
G, H, I, J, K, L, M, N
Flash On+Red-eye
Reduction
D
3
4 Press E.
E
F
Slow-speed Sync
The camera returns to standby mode.
G, H, J
Slow-speed Sync+Red-eye
1 Press B in standby mode.
The screen to set a flash mode
appears.
2 Select a flash mode.
Flash On
0.0
Cancel
OK
3 To compensate the flash
output, press B and then
use R to adjust the value.
Flash On
+0.7
Cancel
OK
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash Compatibility Chart
The following functions are available when using this camera with our flashes.
(x: Available ×: Not available)
AF400T
AF280T
AF200T
AF200S
AF160
AF140
Flash AF540FGZ II AF540FGZ AF200FG
AF360FGZ II AF360FGZ AF160FC
AF500FTZ
AF330FTZ
AF400FTZ
AF240FT
AF140C
AF080C
AF200SA
Function
P-TTL auto flash
External auto flash
Red-eye reduction
x
x
x
×
×
×
×
×
×
×
x
×
×
×
×
×
x
×
×
x
×
×
x
×
3
x
x
x
Automatic switch of the shutter
speed to the flash sync speed
after the flash is charged
x
x
x
x
x
x
x
x
x
Setting the aperture value in G or
I mode
x
x
×
×
×
x
x
×
x
Slow-speed Sync flash
x
x
x
x
x
x
x
x
x
x
x
x
x
×
x
x
x
x
x
×
x
Trailing Curtain Sync flash
x
x
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Contrast-control-sync flash
Slave flash
×
×
×
×
×
×
x
×
Flash Exposure Compensation
AF Assist Light
x
×
×
×
×
x
x
×
Discharging a flash multiple
times
x
x
×
×
×
×
x
×
×
×
×
×
×
×
×
×
×
High-speed sync flash
×
Wireless flash
*1 There is a limit to the available shutter speeds.
*2 Two or more compatible flash units are required.
*3 Available only when using A645, Ak645, FA645, FAk645, or D FA645
lenses.
*5 When the flash setting is MS or M, the aperture value changes automatically
in I mode.
*6 The aperture value changes automatically.
*7 The flash fully discharges.
*4 When the flash setting is MS or M, the aperture value changes automatically.
*8 Unavailable for AF330FTZ.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Preview
• Optical Preview is always used when Multi-exposure, Interval
Shooting, Interval Composite or Mirror Lock-up Shooting is used.
• The display settings and camera operation during Digital Preview
can be changed in [Digital Preview] of the A4 menu. (w p.R19)
• The preview function can also be assigned to O. (w p.R20)
You can easily switch between Optical Preview and Digital Preview
after assigning different kinds of preview methods to the two
controls, U of the main switch and O.
Turn the main switch to U to use the
preview function.
There are two preview methods.
3
For checking the depth of field with the viewfinder.
(Default setting)
Optical Preview
For checking the composition, exposure and focus on
Digital Preview the monitor. (The maximum display time: 60 seconds)
You can magnify or save the preview image.
A4
Setting the Preview Method
1 Select [Button Customization] in A4 menu and
press D.
The [Button Customization] screen appears.
2 Select [Preview Dial] and press D.
The [Preview Dial] screen appears.
3 Select [Optical Preview] or [Digital Preview] and
press E.
4 Press F three times.
The camera returns to standby mode.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Custom Image
• By default, [Custom Image] is set to [Natural].
Select the desired picture style from the following modes and
enjoy taking pictures with a creative finishing tone.
1 Press D in standby mode.
The Custom Image setting screen
appears.
Image Tone
Parameter
Saturation: -4 to +4
Hue: -4 to +4
Bright/Natural/
3
Portrait/Landscape/ High/Low Key Adj: -4 to +4
Vibrant/Radiant
Contrast: -4 to +4
2 Select an image finishing
Bright
Sharpness: -4 to +4
Saturation: -4 to +4
tone.
Toning: Off/Green/Yellow/Orange/Red/Magenta/
Purple/Blue/Cyan
Muted/
Bleach Bypass
Parameter Adj.
Cancel Check
High/Low Key Adj: -4 to +4
Contrast: -4 to +4
OK
Available operations when shooting with the viewfinder
Sharpness: -4 to +4
Sharpness: -4 to +4
Main switch to U
Uses Digital Preview to preview the background
image with the selected effect applied.
Reversal Film
Monochrome
Filter Effect: None/Green/Yellow/Orange/Red/
Magenta/Blue/Cyan/Infrared Filter
H
Saves the preview image (only when the image
can be saved).
Toning: Off/Green/Yellow/Orange/Red/Magenta/
Purple/Blue/Cyan
Proceed to Step 6 if you do not need to change the parameters.
High/Low Key Adj: -4 to +4
Contrast: -4 to +4
3 Press G.
The parameter setting screen appears.
Sharpness: -4 to +4
Cross Processing
Random/Preset 1-3/Favorite 1-3
*1 The settings of a captured image can be saved with [Save Cross Processing]
of the playback mode palette. (p.69)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Set the parameters.
Saturation
Check
Saving the Settings of a Captured
Image
The outcome of Cross Processing varies each time a picture is
taken. If you take a cross processed image that you like, you
can save the Cross Processing settings used in that image so
that you can repeatedly use the same settings.
Cancel
OK
Available operations
AB
CD
Q
Selects a parameter.
Adjusts the value.
3
1 Press B in single image display of playback
mode.
Switches between [Contrast], [Contrast Highlight
Adjustment] and [Contrast Shadow Adjustment].
The playback mode palette appears.
R
M
Switches between [Sharpness], [Fine Sharpness]
and [Extra Sharpness]. (Not available in C mode.)
2 Select a (Save Cross Processing) and press E.
Resets the adjustment value to the default setting.
The camera searches for cross processed images starting from the
most recent image taken.
[No cross processed image] appears if there are no cross
processed images.
5 Press E.
The screen of Step 2 reappears.
3 Use Q to select a cross
100-0001
6 Press E.
Saves this image's Cross
processed image.
Processing settings
The camera returns to standby mode.
Save as Favorite 1
Save as Favorite 2
Save as Favorite 3
Memo
Cancel
OK
• When [Reversal Film] is selected and [White Balance] is set to
[Auto White Balance], images are captured with an effect similar to
using a daylight film.
4 Select the “Favorite” number 1, 2 or 3 to save the
settings and press E.
The settings of the selected image are saved as your “Favorite”
settings.
Memo
• The saved Cross Processing settings can be loaded by selecting
selecting one of the Favorite settings 1 to 3 for the parameter.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Function
Page
Setting the Playback
Functions
Divides a movie or deletes unwanted
segments.
c
Movie Edit
Copies images between memory
cards in SD1 and SD2 slots.
i Image Copy
Playback functions can be set in the
playback mode palette as well as the
B menu.
Image Rotation
Eye-Fi Image
Transfer
Transfers selected images wirelessly
using an optional Eye-Fi card.
e
w p.R34
*1 Not available when a movie is displayed.
Press B in single image display of the
playback mode to display the playback
mode palette.
Rotates captured images.
Useful for image playback on
TV and other display devices
Exit
*2 Not available when a RAW image is displayed.
*3 Available only when a RAW image is saved.
*4 Available only when a movie is displayed.
OK
*5 Available only when an Eye-Fi card is inserted in the SD2 slot.
4
Item
Function
Page
Memo
Image Rotation Changes the rotation information of
• The functions of the playback mode palette can be used only for
the images saved on the memory card that is currently being
played back. To use the functions for the images saved on the
other memory card, switch to the other memory card slot with d
during single image display, then display the playback mode
palette.
S
T
images.
Digital Filter
Color Moiré
Correction
Processes images with digital filters.
h
Reduces color moiré in images.
Changes the number of recorded
pixels of the image.
V
W
Resize
• When saving images that have been
edited with functions such as [Resize],
you can choose whether to save the
Crops out only the desired area of an
image.
Cropping
Saves the image as a new file
images to the memory card in the SD1
or SD2 slot if both cards are available
for recording.
Protects images from being
accidentally erased.
Save to SD1
Y
Z
Protect
Save to SD2
Cancel
Slideshow
Saveas Manual
Plays back images one after another.
OK
• Refer to “Menu Reference” for details
on the B menus. (w p.R26)
Saves the white balance settings of
the captured image as Manual White
Balance.
o
WB
Saves the settings used for an image
captured in Cross Processing mode
of Custom Image as your “Favorite”
settings.
Save Cross
Processing
a
b
RAW
Development
Develops RAW images into JPEG
images and saves them as a new file.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a Single Image
Zoom Display
Images can be magnified up to 16× in playback mode.
Deleting Images One by One
1
Display the image to magnify in single image display.
2 Turn R to the right.
Caution
• Deleted images cannot be restored.
The image magnifies at each click.
100-0001
1 Display the image to delete in single image
display.
4
x2
Available operations
2 Press L.
R to the right
R to the left
ABCD
E
Magnifies the image.
The delete confirmation appears.
Reduces the image.
Changes the area to magnify.
Returns to the entire image display.
Q
Displays the previous or next image without
changing the magnification and the position of
the image to magnify.
3 Select [Delete] and press E.
G
d
Changes the type of information displayed.
Memo
Switches between the memory cards to play
back without changing the magnification and the
position of the image to magnify.
• Select the file format to delete for the images saved in RAW+
format.
• To delete all images, use [Delete All Images] in the B1 menu.
(w p.R27)
Memo
• You can magnify the image by following the same procedure
• You can set the initial magnification with [Quick Zoom] in the B1
menu. (w p.R26)
• When the image is magnified to the actual pixel size, z is
displayed at the bottom right of the screen. If the Q is turned to
view the next or previous image during actual pixel size display, the
next or previous image is displayed in the actual pixel size. The
magnification for the actual pixel size varies depending on the
number of recorded pixels of the image.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Playback
Method
Select & Delete
_
2 Select the images to delete.
001/500
100 0505
Multi-image Display
You can display 6, 12, 20, 35 or 80 thumbnail images at the
same time. (Default setting: 12 Thumbnail Display)
_
1 Turn R to the left in single
100 0505
Available operations
image display.
4
ABCD
E
Moves the selection frame.
The multi-image display screen
appears.
Confirms/cancels the selection of the image to
delete.
J
Selects the range of images to delete.
R
Shows the selected image in single image display.
Use Q to select a different image.
Available operations
ABCD
Q
Moves the selection frame.
In the upper left area of the monitor, the number of selected images
is displayed.
Shows the next/previous page.
d
Switches between the SD1 card and SD2 card.
G
Shows the display
style selection screen.
_
100 0505
3 Press L.
The delete confirmation screen appears.
12 Thumbnail Display
4 Select [Delete] and press E.
Memo
• You can select up to 500 images at a time.
• Protected images cannot be selected.
• You can delete the images selected individually along with the
images selected by specifying the range to delete.
• Use the same steps to select multiple images for the following
functions.
L
Deletes the selected images.
2 Press E.
The selected image appears in single image display.
Memo
• Icons such as U are not displayed on the thumbnail images when
[80 Thumbnail Display] is selected.
• Eye-Fi Image Transfer (w p.R34)
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Folder Display
• Refer to “Menu Reference” for details on folder names. (w p.R31)
Images are grouped and displayed by folder in which they are
saved.
Calendar Filmstrip Display
Images are grouped and displayed by shooting date.
Up to eight folders are displayed at once.
100PENTX
2 Select a folder.
The display style selection screen appears.
100
104
101
105
102
106
103
100–0505
2 Select [Calendar Filmstrip
4
2014.5
THU
SAT
MON
FRI
1
10
19
23
107
Display].
Images are displayed by shooting
date.
2014.6
123
SUN
THU
TUE
1
12
24
Available operations
2/5
ABCD
E
Moves the selection frame.
Shooting date Thumbnail
Displays the images in the folder on the multi-image
display screen.
Available operations
AB
CD
Selects a shooting date.
L
Deletes the folder and all the images in it.
Selects an image taken on the selected shooting
date.
R to the right
Displays the selected image in single image
display.
Deleting a Folder
(R to the left: Returns to displaying images by
shooting date.)
L
Deletes the selected image.
The delete confirmation screen appears.
3 Press E.
2 Select [Delete] and press E.
The selected image appears in single image display.
The selected folder and all the images in it are deleted.
When there are protected images in the folder, select [Delete all]
or [Leave all].
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Slideshow
Image Rotation
You can play back all images saved on a memory card
successively.
Image rotation information is saved according to the orientation
of the camera when the image was shot. When [Auto Image
Rotation] in the B1 menu is set to on (default setting), the
image is automatically rotated based on the rotation information
during playback.
The rotation information of an image can be changed by
following the procedure below.
1 Select Z in the playback mode palette.
The start screen is displayed and
slideshow starts.
Start
1 Display the image to edit in single image display.
4
2 Select S in the playback mode palette.
Available operations
The selected image is rotated in 90° increments and the four
thumbnail images are displayed.
E
Pauses/resumes playback.
CD
B
Displays the next or previous image.
Stops playback.
3 Select the desired rotation
direction and press E.
R
Adjusts the volume of the movie.
The image rotation information is
saved.
After all images are played back, the camera returns to single
image display.
MENU Cancel
OK
Caution
Memo
• When [22. Save Rotation Info] is set to off in the E4 menu, image
rotation information is not saved when shooting. (w p.R41)
• You cannot change the rotation information in the following cases.
• Protected images
• You can change the display settings for slideshow in [Slideshow]
of the B1 menu. Slideshow can also be started from the
Slideshow setting screen. (w p.R26)
• Images without a rotation information tag
• When [Auto Image Rotation] is set to off in the B1 menu
(w p.R26)
• Movie files cannot be rotated.
Memo
• For images captured with [180° Rotation Info] in [Image Capture
Settings] of the A1 menu set to on, the orientation of the camera
when the image was taken is rotated 180° and saved as the
rotation information. (w p.R15)
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing and Processing
Images
Resize/Cropping
Caution
• Only JPEG images captured with this camera can be resized or
cropped. TIFF images and movies cannot be resized or cropped.
RAW images cannot be resized.
Image Copy
• Images already resized or cropped to the minimum file size cannot
be processed.
Copies images between memory cards in SD1 and SD2 slots.
1 Select an image saved on the memory card from
which the images have to be copied, and display
it in single image display.
Resize
4
Changes the number of recorded pixels of the selected image,
and saves it as a new file.
2 Select i in the playback mode palette.
3 Select [Select image(s)] or [Select a folder] and
1 Display the image to edit in single image display.
press E.
2 Select V in the playback mode palette.
4 Select the image(s) or folder to copy.
The screen to select the number of recorded pixels appears.
image(s) or a folder.
3 Use CD to select the
number of recorded pixels.
5 Press G.
You can select an image size smaller
than that of the original image.
The save confirmation screen appears.
Cancel
OK
6 Select the location to save the image(s) or folder
and press E.
4 Press E.
The save confirmation screen appears.
Memo
• A new folder is created at the selected location to save the copied
image(s).
5 Select [Save to SD1] or [Save to SD2] and press
E.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Cropping
Color Moiré Correction
Crops out only the desired area of the selected image and
saves it as a new image.
Reduces color moiré in images.
1 Display the image to edit in single image display.
2 Select h in the playback mode palette.
1 Display the image to edit in single image display.
2 Select W in the playback mode palette.
If the image cannot be edited, [This image cannot be processed]
appears.
The cropping frame to specify the size and position of the area to
crop appears on the screen.
3 Use CD to select the level
and press E.
3 Specify the size and position
of the area to crop by using
the cropping frame.
4
The save confirmation screen appears.
Cancel
OK
4 Select [Save to SD1] or [Save to SD2] and press
Available operations
E.
R
Changes the size of the cropping frame.
Moves the cropping frame.
ABCD
G
Caution
Changes the aspect ratio or Image Rotation setting.
Rotates the cropping frame (only when possible).
• The Color Moiré Correction function can be used only for the JPEG
images captured with this camera. RAW/TIFF images and movies
cannot be corrected.
M
4 Press E.
The save confirmation screen appears.
5 Select [Save to SD1] or [Save to SD2] and press
E.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Filter Name
Tone
Expansion a unique contrast.
Effect
Parameter
Low/Medium/High
Digital Filter
Creates an image with
You can process captured images with digital filters.
The following filters are available.
Creates an image that Contrast: Low/Medium/High
looks as though it was
drawn with a pencil.
Sketch
Scratch Effect: OFF/ON
Filter Name
Effect
Parameter
Brightness: -8 to +8
Creates an image that Intensity: Low/Medium/High
Water Color looks as though it was
Saturation: OFF/Low/Medium/High
painted.
Saturation: -3 to +3
Hue: -3 to +3
Base
Adjusts the parameters
Creates an image that
looks as though it was Low/Medium/High
drawn with a crayon.
Parameter to create the desired
Adj
Pastel
image.
Contrast: -3 to +3
Sharpness: -3 to +3
Lessens the tone of the
image to create an image
that looks as though it was
hand-drawn.
4
Posterization
1 to 5
Extracted Color 1: Red/Magenta/
Blue/Cyan/Green/Yellow
Extracts one or two
specific colors and
makes the rest of the
image black and white.
Extractable Range of Color 1: 1 to 5
Extract
Color
In-Focus Plane: -3 to +3
Extracted Color 2: OFF/Red/
Magenta/Blue/Cyan/Green/Yellow
Blurs a part of the
image to create a
simulated miniature
scene.
In-Focus Width: Narrow/Middle/Wide
Miniature
In-Focus Plane Angle: Horizon/
Vertical/Positive Slope/Negative Slope
Extractable Range of Color 2: 1 to 5
Shading Level: Low/Medium/High
Blur: Low/Medium/High
Creates an image that
looks as though it was Blur: Low/Medium/High
shot with a toy camera.
Toy
Camera
Creates an image with Soft Focus: Low/Medium/High
a soft focus throughout
Soft
Tone Break: Red/Green/Blue/Yellow
Shadow Blur: OFF/ON
the image.
Toning: B3 to A3
Creates an image with
the look of an old photo.
Creates an image with
a special sparkling look
by adding extra glitter
to the highlights of night
scenes or lights
Retro
Effect Density: Small/Medium/Large
Size: Small/Medium/Large
Angle: 0°/30°/45°/60°
Frame Composite: None/Thin/
Medium/Thick
Starburst
High
Contrast
Enhances the contrast
in the image.
1 to 5
reflected on water.
Shading Type: 4 types
Shading Level: -3 to +3
OFF/ON
Creates an image with
darkened edges.
Shading
Creates an image that
looks as though it was Low/Medium/High
shot with a fish-eye lens.
Fish-eye
Slim
Invert Color Inverts image colors.
Changes the horizontal
and vertical ratio of the -8 to +8
image.
Extracts a specific color
Unicolor
Red/Magenta/Blue/Cyan/Green/
Yellow
and makes the rest of the
Bold
image black and white.
Creates a monochrome
image and emphasizes Low/Medium/High
the contrast.
Bold
Monochrome
79
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Display the image to edit in single image display.
Caution
• Only JPEG and RAW images captured with this camera can be
edited with the digital filters. TIFF images cannot be edited.
2 Select T in the playback mode palette.
The screen to select a filter appears.
Memo
3 Select a filter.
100-0001
Base Parameter Adj
• You can apply up to 20 filters to the same image.
Use Q to select a different image.
Proceed to Step 6 if you do not need to
change the parameters.
Recreating Filter Effects
Parameter Adj.
Stop
OK
Retrieves the filter effects of the selected image and applies the
same filter effects to other images.
4
4 Press G.
The parameter setting screen appears.
1 Display a filter-processed image in single image
display.
5 Set the parameters.
Brightness
2 Select T in the playback mode palette.
3 Select [Recreating filter
Cancel
OK
effects] and press E.
Applying the digital filter
Recreating filter effects
The filter effects used for the selected
image appear.
Available operations
Searching for the original image
AB
CD
Selects a parameter.
Adjusts the value.
OK
MENU
4 To check the parameter
100-0001
6 Press E.
Reapplies following digital filter
details, press G.
effects from previous image
The save confirmation screen appears.
Press G again to return to the
previous screen.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.--
--
--
--
--
7 Select [Apply additional filter(s)], [Save to SD1] or
2109..--
--
OK
[Save to SD2], and press E.
Details
Select [Apply additional filter(s)] when you want to apply additional
filters to the same image. The screen of Step 3 reappears.
5 Press E.
The image selection screen appears.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Use Q to select an image
for applying the same filter
effects.
100-0001
Movie Edit
Performs digital filter
processing to this image
1 Display the movie to edit in single image display.
You can only select an image saved in
the same memory card that has not
been processed with a filter.
2 Select c in the playback mode palette.
OK
The screen to edit a movie appears.
7 Press E.
3 Select the point where you
The save confirmation screen appears.
want to divide the movie.
00'00"
10'00"
The frame at the dividing point is
displayed at the top of the screen.
8 Select [Save to SD1] or [Save to SD2] and press
E.
4
Up to four points can be selected to divide
Stop
OK
the original movie into five segments.
Memo
Available operations
• If [Searching for the original image] is selected in Step 3, the
original image prior to digital filter application can be retrieved.
A
Plays back/pauses a movie.
Forwards a frame (when paused).
Fast-forwards playback.
D
Press and hold D
C
Reverses a frame (when paused).
Fast-reverses playback.
Press and hold C
R
G
Adjusts the volume.
Confirms/cancels a dividing point.
Proceed to Step 7 if you do not want to delete any segment.
4 Press L.
The screen to select segments to delete is displayed.
5 Use CD to move the
selection frame and press
E.
00'05"
10'00"
The segments to delete are specified.
(Multiple segments can be deleted at
once.)
Select segments for deletion
MENU
OK
Press E again to cancel the selection.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press F.
4 Press G.
The screen of Step 3 reappears.
The screen for selecting the parameter setting method appears.
7 Press E.
_
5 Select the parameter setting
001/500
100 0505
The save confirmation screen appears.
method and press E.
Develop images as shot
8 Select [Save to SD1] or [Save to SD2] and press
Develop images with
modified settings
E.
OK
Memo
•
Select dividing points in chronological order from the beginning of
the movie. When canceling the selected dividing points, cancel each
of them in reverse order (from the end of the movie to the beginning).
In an order other than specified, you can neither select dividing
points nor cancel the selections of the dividing points.
Develop
images as shot Pixels, and JPEG Quality.
Allows you to change Image Capture Settings (File
Allows you to change File Format, JPEG Recorded
4
Format, Aspect Ratio, JPEG Recorded Pixels, JPEG
Quality, Color Space), Lens Correction (Distortion
Correction, Lat-Chromatic-Ab Adj, Peripheral Illumin.
Corr., Diffraction Correction, Color Fringe Correction),
White Balance, Custom Image, Digital Filter, HDR,
Sensitivity, High-ISO NR, and Shadow Correction.
Develop
images with
modified
settings
RAW Development
You can develop RAW images into JPEG or TIFF format.
6 Set the parameters.
100-0001
Image Capture Settings
1 Select b in the playback mode palette.
The screen for selecting a RAW image processing option appears.
2 Select the desired option and press E.
Select single image
Develops an image.
Available operations
Develops up to 500 images with the same
settings.
Select multiple images
AB
CD
Q
Selects a parameter.
Adjusts the value.
Develops up to 500 images in the selected
folder with the same settings.
Select a folder
Selects a different image (when in single image
display).
When [Select single image] is selected, proceed to Step 6.
The image/folder selection screen appears.
For Image Capture Settings and Lens Correction, press D and use
AB to select an item.
For White Balance, Custom Image and Digital Filter, press D to
display the setting screen.
3 Select the image(s) or a folder.
image(s) or a folder.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press E.
Protecting Images
The save confirmation screen appears.
You can protect images from being accidentally deleted.
8 Select [Save to SD1] or [Save to SD2] and press
E.
Caution
When [Select single image] is selected, select [Continue] or [Exit],
and press E.
• Even protected images are deleted if the inserted memory card is
formatted.
Caution
1 Select Y in the playback mode palette.
•
Only RAW images captured with this camera can be developed. Images
captured with other cameras cannot be processed on this camera.
The screen for selecting the unit for processing appears.
4
2 Select [Select image(s)] or
Memo
[Select a folder] and press
• You cannot save the background image or use Digital Preview
while setting the Custom Image or White Balance parameters.
• When the White Balance parameter is set to [Manual White
Balance], press G to display the fine-tuning screen.
• The Digital Filter parameter cannot be applied to RAW images
captured when [HDR Capture] of the A1 menu is set.
• When [Select multiple images] or [Select a folder] is selected in
Step 2, a folder with a new number is created, and the JPEG
images are stored in it.
Select image(s)
E.
Select a folder
OK
3 Select the image(s) or a folder.
image(s) or a folder.
Proceed to Step 5 if [Select a folder] is selected.
• With the provided software “Digital Camera Utility 5”, you can
4 Press G.
The confirmation screen appears.
5 Select [Protect] and press E.
To remove protection from the image, select [Unprotect].
Memo
• To protect all images stored in the memory card, select [Protect All
Images] of the B1 menu. (w p.R26)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Connecting the Camera to
an AV Device
• Check the operating manual of the AV device and select a suitable
input terminal for connecting the camera.
• If you intend to use the camera continuously for a long period, use
of the optional AC adapter kit is recommended.
Connect to an AV device, such as a TV, equipped with an HDMI
terminal to display Live View images while shooting or to play
back images in playback mode.
Make sure to have a commercially available HDMI cable
equipped with an HDMI terminal (type D).
• By default, the maximum resolution supported by both the AV
device and camera is automatically selected. If it fails to play back
images properly, change the setting in [HDMI Out] of the D2
menu. (w p.R30)
1 Turn the AV device and camera off.
4
2 Open the terminal cover of the camera, and
connect the HDMI cable to the HDMI terminal.
3 Connect the HDMI cable to the input terminal on
the AV device.
4 Turn the AV device and camera on.
The camera turns on in HDMI mode, and the camera information
is displayed on the screen of the connected AV device.
Caution
• While the camera is connected to an AV device, nothing is
displayed on the camera monitor. Also, you cannot adjust the
volume on the camera. Adjust the volume on the AV device.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Macintosh
The captured images can be transferred to a computer by
connecting the camera using a USB cable and can be managed
using the provided software.
OS
Mac OS X 10.9 / 10.8 / 10.7 / 10.6
Intel Core 2 Quad or higher
4 GB or more
CPU
RAM
Program installation and start-up: 100 MB or more
Space taken up on HDD (per file):
[JPEG] Approximately 25 MB
System Requirements
HDD
[TIFF] Approximately 150 MB
We recommend the following system requirements to connect
the camera to a computer or to use the provided software
“Digital Camera Utility 5”.
[RAW] Approximately 70 MB
Monitor 1280×1024 pixels, 24 bit full-color or higher
Memo
• QuickTime is required to play back movies transferred to a
computer. You can download it from the following site:
http://www.apple.com/quicktime/download/
Windows
5
Windows 8.1 (32 bit/64 bit) / Windows 8 (32 bit/64 bit) /
OS
Windows 7 (32 bit/64 bit) / Windows Vista (32 bit/64 bit)
CPU
RAM
Intel Core 2 Quad or higher
4 GB or more
Program installation and start-up: 100 MB or more
Space taken up on HDD (per file):
[JPEG] Approximately 25 MB
HDD
[TIFF] Approximately 150 MB
[RAW] Approximately 70 MB
Monitor 1280×1024 pixels, 24 bit full-color or higher
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Connecting the Camera to a Computer
• The camera cannot be operated while it is connected to a
computer. To operate the camera, terminate the USB connection
on the computer, then turn off the camera and remove the USB
cable.
Connect the camera to a computer using an USB cable.
Make sure to have a commercially available USB cable
equipped with a micro B terminal.
1 Turn the computer on.
2 Turn the camera off.
Memo
• When connected to a computer, use of the optional AC adapter kit
is recommended.
• The USB connection mode when connecting the camera to a
computer can be set in [USB Connection] of the D2 menu.
(w p.R30) Normally, you do not need to change the default
setting ([MSC]).
3 Open the terminal cover of the camera, and
connect the USB cable to the USB terminal.
USB 2.0
USB 3.0
• A memory card with a built-in wireless LAN “Eye-Fi card” (Wi-Fi
transmission) or a “Flucard” compatible with this camera can be
used. By using these cards, images can be transferred from the
camera to a computer or other device via wireless LAN.
(w p.R34)
5
USB Terminal
The micro B terminal supports both USB 3.0 cables and USB 2.0
cables. Both types can be used with this camera. If the host
controller of the device to be connected to the camera supports
USB 3.0, the use of a USB 3.0 cable makes the data transfer
process faster.
4 Connect the USB cable to the USB port of the
computer.
5 Turn the camera on.
The camera is recognized as a removable disk.
If the “645Z” dialog appears, select [Open folder to view files].
6 Save the captured images to the computer.
7 Disconnect the camera from the computer.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Provided
Software
For Windows 7
1 Turn the computer on.
Shut down other software running.
“Digital Camera Utility 5” is included on the provided CD-ROM
(S-SW150). Using the Digital Camera Utility 5, you can manage
images saved on a computer, develop RAW images taken with
this camera and adjust the color of them.
2 Place the CD-ROM (S-SW150) into the optical
drive.
The [Software Install] screen appears.
If the [Software Install] screen does not appear:
Compatible file formats
.jpg (JPEG), .tif (TIFF), .pef (RAW files in our original format),
.dng (RAW files in DNG format)
1 Click [Computer] from the Start menu.
2 Double-click the optical drive (S-SW150) icon.
3 Double-click [Setup.exe].
5
3 Click [32bit] or [64bit].
Installing the Software
Select according to the operating
environment.
You can install the software from the provided CD-ROM.
The screen to select a desired
language appears.
Memo
•
When multiple accounts have been setup on the computer, log on with an
account that has administrative rights before installing the software.
• The installation procedure varies depending on your operating
environment. Refer to the following to install the software.
4 Select the desired language and click [OK].
The [InstallShield Wizard] screen appears in the selected
language.
5 Click [Next].
Follow the instructions on the screen to perform subsequent steps.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
For Mac OS
1 Turn the Macintosh on.
Shut down other software running.
2 Place the CD-ROM (S-SW150) into the optical
drive.
The CD-ROM icon appears on the desktop.
If the CD-ROM icon does not appear:
1 Select [Preferences] in the [Finder] menu.
2 Tick the [CDs, DVDs, and iPods] check box on the
[General] tab.
3 Double-click the CD-ROM (S-SW150) icon.
4 Double-click the [Software Installer] icon.
5
5 Click [Digital Camera Utility
5].
Follow the instructions on the screen
to perform subsequent steps.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Laboratory Mode
The control panel for adjusting the image appears here.
Digital Camera Utility 5 Screen
When Digital Camera Utility 5 is launched, the following screen
appears.
1
2
Memo
• The screenshots used in this explanation are for Windows.
Browser Mode
You can perform the file management functions such as
viewing and managing the images.
5
4
4
8
1
2
5
7
3
5
4
4
6
8
90
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Menu Bar
Viewing the Help Menu
You can execute a function and change various settings here.
For Macintosh, the Menu bar appears at the top of the desktop.
Refer to the Help menu for details on using the Digital Camera
Utility 5 program.
2 Tool Bar
Frequently used functions are provided as Tool bar buttons.
1 Click the
button on the Tool bar.
Or, select [Digital Camera Utility 5 Help] from the [Help] menu.
3 Navigation Panel
This panel is only displayed in Browser mode. There are “Folders”,
“Favorites”, “Checkmark 1”, “Checkmark 2”, and “Checkmark 3”
panels.
4 Control Panel
Regarding User Registration
In order to better serve you, we request that you complete the user
registration.
The shooting information and settings of the selected image
appear in this panel.
The control panel display varies depending on the mode.
1 Click [User Registration] on the [Software Install]
5 Image View Page
screen.
5
The image selected from the image list is displayed.
When multiple image display pages are open, the images can be
arranged left to right or up and down by dragging the tab. For
Macintosh, select [Align images vertically] or [Align images
horizontally] in the [Window] menu.
A world map for Internet User
Registration is displayed.
6 List of images in the current folder
The list of images in the selected folder appears here.
7 List of candidate images for editing
2 If your computer is connected to the Internet, click the
displayed country or area and then follow the
instructions to register your software.
The list of images that can be edited appears here.
8 Status Bar
Information on the selected item appears.
Note that you can only register online if your country or area is
shown.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Flash Accessories
Auto Flash AF540FGZ II
Several accessories are provided for use with this camera.
Please contact our service center for details regarding the
accessories.
Auto Flash AF360FGZ II
The AF540FGZ II and
AF360FGZ II are P-TTL auto
flash units with a maximum guide
number of approximately 54 and
36 (both ISO 100/m),
respectively. Their features
include slave-sync flash,
Products marked with an asterisk (*) are the same as those
supplied with the camera.
AF540FGZ II
Power Supply Accessories
contrast-control-sync flash, high-
speed sync flash, wireless flash,
slow-speed sync and trailing
curtain sync flash.
Battery Charger kit K-BC90 (*)
(Kit includes Battery charger D-BC90 and AC plug cord.)
Rechargeable Lithium-ion Battery D-LI90 (*)
AC Adapter Kit K-AC132
(Kit includes AC adapter D-AC120 and AC plug cord.)
Lets you power this camera from an AC outlet.
6
AF360FGZ II
Auto Flash AF200FG
The AF200FG is a P-TTL auto
flash unit with a maximum guide
numberof approximately 20 (ISO
100/m).
It features contrast-control-sync
flash and slow-speed sync flash
when combined with the
AF200FG
AF540FGZ, AF540FGZ II,
AF360FGZ or AF360FGZ II unit.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Macro Flash AF160FC
Interchangeable Focusing Screen
The AF160FC is a flash system
especially designed for macro
photography to take close,
AF Framed Matte DF-80 (*)
shadowless pictures of small
objects. It is compatible with
existing TTL auto flash functions
and can be used with a wide
range of PENTAX cameras by
using the provided adapter rings.
AF160FC
AF Cross-Lined Matte DG-80
Hot Shoe Adapter FG
Extension Cord F5P
AF Golden Section Matte DK-80
Hot Shoe Adapter FG
6
Off-camera Shoe Adapter F
Use the adapters and cords to
use the external flash away from
the camera.
Cable Switch CS-205
Off-camera Shoe Adapter F
Connect to the cable switch
terminal and operate the camera
shutter release button. The cord
length is 0.5 m.
For Viewfinder
Large Eyecup 645 O-EC107 (*)
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
Strap
Camera Strap O-ST150 (*)
Used for remote control shooting.
Operating distance for remote control
From the front of camera: approx. 4 m
From the back of camera: approx. 2 m
Other Accessories
Body Mount Cap 645 (*)
Remote Control F
Hot Shoe Cover FK (*)
Sync Socket 2P Cap (*)
Imagesensor Cleaning Kit O-ICK1
FLUCARD O-FC1
Remote Control Waterproof
O-RC1
This SD memory card has a built-in
wireless LAN (Wi-Fi transmission)
function. Connect with a
6
communication terminal such as a
smartphone or tablet via wireless
LAN and operate the
communication terminal to shoot or
view images. (w p.R34)
GPS Unit O-GPS1
By attaching the O-GPS1 to the hot
shoe, the latitude, longitude,
altitude, direction, and Coordinated
Universal Time (UTC) can be
recorded in the image file.
The Electronic Compass can be
used with this camera. (w p.R18)
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
Description
Error Messages
Not enough battery
power remaining to
activate Pixel Mapping
These messages appear when you try
to perform Pixel Mapping or Sensor
Cleaning, or to update the firmware if
the battery level is insufficient. Install a
fully charged battery.
Error Messages
Description
Not enough battery
power remaining to
clean sensor
The memory card is full and no more
images can be saved. Insert a new
memory card or delete unwanted files.
Memory card full
No image
Not enough battery
power remaining to
update the firmware
There are no images that can be
played back on the memory card.
You are trying to play back an image in
a format not supported by this camera.
You may be able to play it back on a
computer.
Unable to update firmware.
There is a problem with the
firmware update file
Unable to update the firmware. The
update file is damaged. Try
downloading the update file again.
This image cannot be displayed
No card in the camera
The maximum folder number (999) is
being used, and no more images can
be saved. Insert a new memory card or
format the card.
There is no memory card inserted in
the camera.
Image folder cannot be created
Unable to store image
The memory card has a problem, and
image capture and playback are
impossible. You may be able to play it
back on a computer.
Or, the camera failed to initialize the
Eye-Fi function when using the Eye-Fi
card. Press E.
The image could not be saved
because of a memory card error.
Memory card error
6
The camera was unable to adjust the
manual white balance. Try the
operation again.
The operation could not be
completed correctly
You are trying to select more than the
maximum number of images for Select
& Delete, Protect, RAW Development,
Image Copy, or Eye-Fi Image
Transfer.
The memory card you have inserted is
unformatted or has been previously
used on another device and is not
compatible with this camera. Use the
card after formatting it with this
No more images
can be selected
Card is not formatted
There are no images that can be
processed using the Digital Filter or
RAW Development function.
No image can be processed
The write-protect switch on the
memory card you have inserted is
Card is locked
You are trying to magnify an image
that cannot be magnified.
This image cannot be magnified
The image is protected
You are trying to delete an image that
is protected. Remove protection from
the image. (p.83)
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
Description
Troubleshooting
Appears when you try to perform
Digital Filter, Color Moiré Correction,
Resize, Cropping, Save as Manual
WB, RAW Development, or Movie Edit
for images captured with other
cameras, or when you try to perform
Resize or Cropping for minimum file
size images.
In rare cases, the camera may not operate correctly due to
static electricity. This can be remedied by taking the battery out
and putting it back in again. When the mirror remains in the UP
position, take the battery out and put it back in again. Then, the
mirror will retract when the camera is turned on again. If, after
performing these procedures, the camera operates correctly, it
does not require any repairs.
This image cannot be processed
You are trying to set a function that is
not available for the exposure mode
that is set.
This function is not available
in the current mode
We recommend checking the following items before contacting
a service center.
The camera will turn off because its
internal temperature is too hot. Leave
the camera turned off until it has had
time to cool down before turning on the
camera again.
The camera will turn off
to prevent damage from
overheating
Problem
Cause
Remedy
Battery is not installed Check the orientation of the
The camera
does not turn
on.
properly.
battery.
Images cannot be transferred when
The battery power is
low.
Set the Eye-Fi communication [Action Mode] is not set to [SELECT] in
Charge the battery.
to “SELECT”
Image not found
Cannot be selected
[Wireless Memory Card] of the D3
menu. (w p.R34)
6
There is no available Insert a memory card with
space on the memory available space or delete
The shutter
cannot be
released.
There are no images that can be
transferred when an Eye-Fi card is
used.
card.
unwanted images.
Data is being
processed.
Wait until processing is finished.
This folder cannot be selected
because the number of files exceeds
the maximum number allowed.
v
cannot work well for low-
contrast objects (the sky, white
walls, etc.), dark colors, intricate
designs, rapidly-moving objects or
scenery shot through a window or
a net-like pattern.
Lock focus on another object
located at the same distance as
your subject, then aim at the
target and take a picture.
Caution
The subject is difficult
to focus on.
• Error messages related to a memory card appear for each card slot
being used. If an error message appears, take the appropriate
action for the respective card slot.
Autofocus
does not work.
Alternatively, use
w.
The subject is too
close.
Move away from the subject and
take a picture.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
The focus
cannot be
locked.
AF Mode of Live View Set [Contrast AF] to e, g, h
The camera is
not recognized
when it is
connected to a
computer.
The USB connection Set [USB Connection] to [MSC]
mode is set to [PTP]. in the D2 menu. (w p.R30)
Activate [Dust Removal] from
the D4 menu. The Dust
Removal function can be
Dust or dirt
particles
appear in
images.
The CMOS sensor is
activated every time the camera
dirty or dusty.
is turned on and off. (w p.R37)
Refer to “Sensor Cleaning” if the
problem persists. (w p.R37)
There are
pixels in the
monitor or
captured
images that do sensor.
not light up or
Activate [Pixel Mapping] from
the D4 menu. (w p.R35)
There are defective
It takes about 30 seconds to
pixels in the CMOS
correct the defective pixels, so
6
be sure to install a fully charged
battery.
remain lit.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
AF.S Setting................................... R40
Aperture Priority Automatic Exposure
mode............................................. 48
Auto EV Compensation.................. R39
Auto Image Rotation ...................... R26
AUTO ISO Parameters .................. R17
Auto Power Off............................... R34
Auto Resize.................................... R35
Auto Screen Rotation..................... R30
Auto White Balance (White Balance)
...................................................... 53
AWB in Tungsten Light .................. R40
Bulb (B) Mode Options .................. R39
Button Customization .................... R20
Index
Symbols
A menu .................................. R5, R15
C menu .................................. R8, R24
B menu.................................. R8, R26
D menu ................................... R9, R28
E menu ................................. R11, R39
C
City ................................................ R28
Color Space................................... R41
Color Temperature (White Balance)
...................................................... 55
Color Temperature Steps .............. R40
Contrast AF ................................... R18
Numerics
180° Rotation Info.......................... R15
1st Frame Action in AF.C............... R41
4-way Controller Options ............... R42
A
6
Action in AF.C Continuous............. R41
AdobeRGB..................................... R41
AE-L with AF Locked ..................... R39
AF Button....................................... R20
AF Fine Adjustment ....................... R42
AF with Remote Control................. R41
B
Base Parameter Adj (Digital Filter)
...................................................... 79
Bracketing Order............................ R40
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright Holder............................ R33
Copyright Information .................... R33
Create New Folder......................... R32
Cross Processing (Custom Image)
...................................................... 69
Custom setting menu............. R11, R39
Distortion Correction ...................... R16
DNG ............................................... R15
D-Range Settings........................... R16
DST (daylight saving time)............. R29
Dust Alert ....................................... R36
Dust Removal................................. R37
Dynamic range............................... R16
Eye-Fi Image Transfer................... R34
F
File Format .................................... R15
File Name ...................................... R32
File No. .......................................... R33
Firmware Info/Options ................... R38
Flicker Reduction........................... R34
Fluorescent - Cool White (White
E
D
E-Dial Programming....................... R20
Enable/Disable Controls................. R43
Exif ................................................. R33
Expanded Area AF (AF Active Area)
...................................................... 45
Exposure Mode (USER mode)
Default settings................................ R5
Delete all images ........................... R27
Destination..................................... R29
Diffraction Correction..................... R16
Display Color ................................. R30
6
Balance)........................................ 53
Fluorescent - Daylight Color (White
Balance)........................................ 53
Fluorescent - Daylight White (White
Balance)........................................ 53
Fluorescent - Warm White (White
Balance)........................................ 53
Focus Peaking............................... R18
Folder Name.................................. R31
........................................... R15, R23
Exposure Setting (Movie)............... R24
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Framerate ...................................... R24
Image storage capacity.................. R49
ISO AUTO Setting.......................... R17
Lens Correction ............................. R16
Link AE and AF Point .................... R39
G
GPS ............................................... R18
GPS Time Sync ............................. R18
Green button.................................. R20
Grid Display ........................... R19, R26
M
Memory.......................................... R22
Memory Card Options ........... R15, R24
Meter Operating Time.................... R39
Mirror Up Operation....................... R42
Movie Capture Settings ................. R24
H
HDMI Out....................................... R30
HDR Capture ......................... R16, R24
High-ISO NR.................................. R17
Highlight Alert ........................ R19, R26
Highlight Correction ....................... R16
Hold AF Status............................... R41
J
JPEG.............................................. R15
6
K
L
Lat-Chromatic-Ab Adj..................... R16
LCD Display ................................... R30
LCD Display Settings ..................... R30
LCD Panel Illumination................... R41
I
Illumination Button ......................... R21
Image Capture Settings................. R15
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie menu ............................. R8, R24
Movie SR ....................................... R25
MSC............................................... R30
Multi Auto White Balance (White
Balance)........................................ 53
Playback Info Display selection screen
...................................................... 19
Playback menu........................ R8, R26
Power frequency ............................ R34
Program Automatic Exposure mode
...................................................... 48
Protect All Images.......................... R26
PTP ................................................ R30
Recording Sound Level ................. R24
Reset ..................................... R35, R43
Rotate Display 180°....................... R19
Rotation Direction (E-Dial
Programming)............................ R20
N
Noise Reduction ............................ R17
S
Save Rotation Info......................... R41
Save USER Mode ......................... R22
Sensitivity Priority Automatic Exposure
mode............................................. 48
Sensitivity Steps ............................ R39
Sensor Cleaning............................ R37
6
O
One Push File Format.................... R21
One-Push Bracketing..................... R40
Q
Quality Level .................................. R15
Quick Zoom.................................... R26
P
PEF................................................ R15
Peripheral Illumination Correction.. R16
Photographer................................. R33
Pixel Mapping ................................ R35
Pixels ............................................. R15
R
RAW............................................... R15
RAW/Fx Button .............................. R20
Rec. Mode menu..................... R5, R15
Recorded Pixels.................... R15, R24
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequential Numbering ................... R33
Set-up menu ............................ R9, R28
Shadow Correction ........................ R16
Shake Reduction Options.............. R43
Shutter & Aperture Priority Automatic
Exposure mode............................. 48
Shutter Priority Automatic Exposure
mode............................................. 48
Slow Shutter Speed NR................. R17
Sound Effects ................................ R29
Specifications................................. R45
sRGB ............................................. R41
Switching between the memory cards
...................................................... 39
V
Volume .................................. R24, R29
W
WB Adjustable Range ................... R40
WB When Using Flash .................. R40
Wi-Fi transmission......................... R34
Wireless LAN................................. R34
Wireless Memory Card.................. R34
World Time .................................... R28
T
Time Setting................................... R29
6
X
Z
U
104
Download from Www.Somanuals.com. All Manuals Search And Download.
and warranty policy. In any case, however, shipping charges and
customs clearance fees to be borne by the sender. To prove the date of
your purchase when required, please keep the receipt or bills covering
the purchase of your camera for at least a year. Before sending your
camera for servicing, please make sure that you are sending it to the
manufacturer’s authorized representatives or their approved repair
shops, unless you are sending it directly to the manufacturer. Always
obtain a quotation for the service charge, and only after you accept the
quoted service charge, instruct the service station to proceed with the
servicing.
WARRANTY POLICY
All our cameras purchased through authorized bona fide photographic
distribution channels are guaranteed against defects of material or
workmanship for a period of twelve months from the date of your
purchase. Service will be rendered, and defective parts will be replaced
without cost to you within that period, provided the camera does not
show evidence of impact, sand or liquid damage, mishandling,
tampering, battery or chemical corrosion, operation contrary to
operating instructions, or modification by an unauthorized repair shop.
The manufacturer or its authorized representatives shall not be liable for
any repair or alterations except those made with its written consent and
shall not be liable for damages from delay or loss of use or from other
indirect or consequential damages of any kind, whether caused by
defective material or workmanship or otherwise; and it is expressly
agreed that the liability of the manufacturer or its representatives under
all guarantees or warranties, whether expressed or implied, is strictly
limited to the replacement of parts as hereinbefore provided. No refunds
will be made on repairs by non-authorized service facilities.
• This warranty policy does not affect the customer’s statutory
rights.
• The local warranty policies available from our distributors in
some countries can supersede this warranty policy. Therefore,
we recommend that you review the warranty card supplied with
your product at the time of purchase, or contact our distributor
in your country for more information and to receive a copy of the
warranty policy.
6
Procedure During 12-month Warranty Period
Any camera which proves defective during the 12-month warranty
period should be returned to the dealer from whom you purchased the
camera or to the manufacturer. If there are no representatives of the
manufacturer in your country, send the camera to the manufacturer,
with postage prepaid. In this case, it will take a considerable length of
time before the camera can be returned to you owing to the complicated
customs procedures required. If the camera is covered by warranty,
repairs will be made and parts replaced free of charge, and the camera
will be returned to you upon completion of servicing. If the camera is not
covered by warranty, regular charges of the manufacturer or of its
representatives will apply. Shipping charges are to be borne by the
owner. If your camera was purchased outside of the country where you
wish to have it serviced during the warranty period, regular handling and
servicing fees may be charged by the manufacturer’s representatives in
that country. Notwithstanding this, your camera returned to the
manufacturer will be serviced free of charge according to this procedure
105
Download from Www.Somanuals.com. All Manuals Search And Download.
For customers in USA
STATEMENT OF FCC COMPLIANCE
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Class B Personal Computers and Peripherals
We:
RICOH IMAGING AMERICAS
CORPORATION
th
Located at: 633 17 Street, Suite 2600
Denver, Colorado 80202 U.S.A.
Phone: 800-877-0155
FAX: 303-790-1131
Declare under sole responsibility that the product identified herein
complies with 47CFR Parts 2 and 15 of the FCC rules as a Class B
digital device. Each product marketed is identical to the representative
unit tested and found to be compliant with the standards. Records
maintained continue to reflect the equipment being produced can be
expected to be within the variation accepted, due to quantity production
and testing on the statistical basis as required by 47CFR §2.909.
Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired
operation. The above named party is responsible for ensuring that the
equipment complies with the standards of 47CFR §15.101 to §15.109.
6
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Product Name:
Lens-interchangeable medium-
format digital SLR (Single Lens
Reflex) Camera
* Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Model Number:
PENTAX 645Z
Pour les utilisateurs au Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
Contact person: Customer Service Manager
Date and Place: March, 2014, Colorado
FOR CALIFORNIA, U.S.A. ONLY
Perchlorate Material-special handling may apply.
The lithium battery used in this camera contains perchlorate material,
which may require special handling.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Information for Users on Collection and Disposal of Old
Equipment and Used Batteries
1. In the European Union
These symbols on the products, packaging and/or
accompanying documents mean that used electrical and
electronic equipment and batteries should not be mixed with
general household waste.
Used electrical/electronic equipment and batteries must be
treated separately and in accordance with legislation that
requires proper treatment, recovery and recycling of these
products.
By disposing of these products correctly you will help ensure
that the waste undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on
the environment and human health which could otherwise
arise due to inappropriate waste handling.
If a chemical symbol is added beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy metal
(Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in the battery at
a concentration above an applicable threshold specified in the Battery
Directive.
6
For more information about collection and recycling of used products,
please contact your local authorities, your waste disposal service or the
point of sale where you purchased the products.
2. In other countries outside the EU
These symbols are only valid in the European Union. If you wish to
discard used products, please contact your local authorities or dealer
and ask for the correct method of disposal.
For Switzerland: Used electrical/electronic equipment can be returned
free of charge to the dealer, even when you don't purchase a new
product. Further collection facilities are listed on the home page of
www.swico.ch or www.sens.ch.
The CE Mark is a Directive conformity mark of the European
Union.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
RICOH IMAGING COMPANY, LTD.
RICOH IMAGING EUROPE S.A.S
RICOH IMAGING DEUTSCHLAND GmbH
RICOH IMAGING UK LTD.
2-35-7, Maeno-cho, Itabashi-ku, Tokyo 174-8639, JAPAN
(http://www.ricoh-imaging.co.jp)
112 Quai de Bezons, B.P. 204, 95106 Argenteuil Cedex, FRANCE
(http://www.ricoh-imaging.fr)
Am Kaiserkai 1, 20457 Hamburg, GERMANY
(http://www.ricoh-imaging.de)
PENTAX House, Heron Drive, Langley, Slough, Berks SL3 8PN, U.K.
(http://www.ricoh-imaging.co.uk)
RICOH IMAGING AMERICAS
CORPORATION
633 17th Street, Suite 2600, Denver, Colorado 80202, U.S.A.
(http://www.us.ricoh-imaging.com)
RICOH IMAGING CANADA INC.
1770 Argentia Road Mississauga, Ontario L5N 3S7, CANADA
(http://www.ricoh-imaging.ca)
RICOH IMAGING CHINA CO., LTD.
23D, Jun Yao International Plaza, 789 Zhaojiabang Road, Xu Hui District,
Shanghai, 200032, CHINA
(http://www.ricoh-imaging.com.cn)
http://www.ricoh-imaging.co.jp/english
• Specifications and external dimensions are subject to change without notice.
53071
Copyright © RICOH IMAGING COMPANY, LTD. 2014
R01DTC14 Printed in Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|
PYLE Audio TV Video Accessories PAVS008 User Guide
Radio Shack Cordless Telephone ET 536 User Guide
RCA Cassette Player CDP18S711 User Guide
RCA Clock RC220 User Guide
Renesas Server HEW Target User Guide
ResMed Oxygen Equipment 618143 Quattro FX NV User Guide
RTS Stereo Amplifier MDA 100 User Guide
Samsung Security Camera SPH 20W P User Guide
Sanyo Flat Panel Television DP26648 User Guide
Sanyo Headphones SHS8000 User Guide