™
ApneaLink
Your link to better sleep health
ApneaLink is a simple, cost-effective
sleep-screening tool that objectively
identifies patients at risk for obstructive
sleep apnea (OSA).
Download from Www.Somanuals.com. All Manuals Search And Download.
ApneaLink with oximetry
ResMed’s ApneaLink with oximetry is the premium choice in
screening for OSA. In addition to the features and benefits of
the basic ApneaLink device, the pulse oximeter provides two
additional channels of information—pulse and pulse oximetry,
all three channels in a simple “little blue box.” A simple nasal
cannula is used for sensing patient breathing. Oximetry and
pulse are detected using a choice of either reusable or single-
use patient sensors. The original ApneaLink software has been
enhanced to show a two-page patient report with pulse and
oximetry signals, detailed SpO2 information and waveform data.
The ApneaLink with oximetry is perfect for those who want
more information and are expanding their screening capabilities
to other non-traditional patient areas, such as home oxygen
patients.
Download from Www.Somanuals.com. All Manuals Search And Download.
Electromagnetic Compatibility
TECHNICAL SPECIFICATIONS
APNEALINK AND PULSE OXIMETER
Product complies with all applicable electromagnetic compatibility requirements (EMC) according to IEC60601-
1-2, for residential, commercial and light industry environments. For further details, see “Guidance and
Manufacturer’s Declaration – Electromagnetic Emissions and Immunity” as follows.
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions and Immunity
The ApneaLink is intended for use in the electromagnetic environment specified below. The customer or user
of the ApneaLink should ensure that the system is used only in such an environment.
Signal Recording
Breathing sounds
Respiratory flow
Blood oxygen saturation
Pulse
Battery voltage
Sampling Rates for the Channels
Respiratory flow/breathing sounds: 100 Hz
Saturation: 1 Hz
Emissions test
Compliance Electromagnetic environment—guidance
RF emissions CISPR11
Group 1
The ApneaLink uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are unlikely to cause
any interference in nearby electronic equipment
Pulse: 1 Hz
Battery: 1 Hz
RF emissions CISPR11
Class B
—
The ApneaLink is suitable for use in all establishments, including
domestic establishments and those directly connected to the
public low-voltage network that supplies buildings used for
domestic purposes.
Harmonic Emissions
IEC 61000-3-2
Signal Processing
Signal recording: 20 Bit
Signal storage: 16 Bit
Internal Memory
Storage capacity: 15 MB
Recording period: 8 hours minimum
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
—
Medical Electrical Equipment needs special precautions with respect to EMC and needs to be installed and
put into service according to EMC information provided in this document.
Power Supply to Recorder
Warnings: The ApneaLink should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary, the ApneaLink should be observed to verify normal, operation in the configuration
in which it will be used. The use of accessories other than those specified in this manual is not
recommended. They may result in increased emissions or decreased immunity of the ApneaLink.
2 NiMH rechargeable batteries: Mignon/AA/1.2V/
at least 2.1 Ah or
2 batteries: LR 6/Mignon/AA/1.5V/at least 2.1 Ah
Weight
Recorder (without rechargeable batteries or batteries):
Approximately 50 g (1.8 oz)
Pulse Oximeter: Approximately 30 g (1.1 oz)
Operating Conditions
Temperature: 20°C to 40°C (68°F to 104°F)
Humidity: 10% to 90% RH (non condensing)
Shipment/Storage Conditions*
Temperature: -20°C to +50°C (-4°F to +122°F)
Humidity: 10% to 90% RH
*Recorder without rechargeable batteries or batteries
Operating/Storage Air Pressure
800 hPa to 1060 hPa
Effective Range
Flow sensor: -10 hPa to +10 hPa
SpO2: +/- 2 digits
Pulse: +/- 3 digits
Interfaces
Nasal pressure cannula: Luer connection
Pulse oximeter: 3-pin Binder plug
Computer: Fullspeed USB 1.1
Dimensions
Recorder (length x width x height): 125 x 60 x 30 mm
(4.9" x 2.4" x 1.2")
ORDERING INFORMATION & PRODUCT CODES
ApneaLink
Optional Accessories and Disposables
(US, Latin America and Canada)
US and Latin America
22302
22303
Nasal Cannulas (25/pk)
Nasal/Oxygen Cannula (25/pk)
Belt, reusable
70388
70319
629052
70406
70412
Canada
1 Apnealink device
3 Nasal Cannulas
1 Reusable Belt
1 Program CD
2 AA Batteries
1 Carrying Case
Belt, Single Use (24/pk)
Sensor, Oximeter-Single Use
1 Quick Software Setup Guide
1 USB download cable
Sensor, Oximeter (Flex Wrap)-Reusable 1431002
Tape, Sensor (for Flex Wrap Sensor), (25/pk) 70276
Sensor, Oximeter (Soft Sensor)-Reusable 70413
ApneaLink Oximetry Accessories Kit
US and Latin America
22304
22308
Canada
1 Nonin XPOD oximeter
1 Sensor clip
3 Disposable Sensors
Pulse oximeter: (length x width x height): 53 x 20 x 15 mm
(2.1" x 0.8" x 0.6")
ResMed Corp Poway, CA, USA +1 858 746 2400 or 1 800 424 0737 (toll free), ResMed Ltd Bella Vista, NSW, Australia +61 (2) 8884 1000 or 1 800 658 189 (toll free). Offices in Austria, Brazil, Finland, France, Germany, Hong Kong, Japan,
Malaysia, Netherlands, New Zealand, Singapore, Spain, Sweden, Switzerland, United Kingdom (see website for details).
ApneaLink is a trademark of ResMed Ltd. and is registered in U.S. Patent and Trademark Office. ©2006 ResMed. 1011262/1 06 10
Global leaders in sleep and respiratory medicine
Download from Www.Somanuals.com. All Manuals Search And Download.
|