M38D29T2-RLFS
Emulator MCU Board for 38D2 Group
User’s Manual
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
Jan. 10, 2008
(1/4)
REJ10J1789-0100
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Connection Procedure
(1) For M38D29T2-RLFS-FP
1 Mount the NQPACK064SA160 to the foot pattern of the user system.
2 Attach the included M3T-F160-64NSA to the M38D29T2-RLFS.
3 Mount the YQPACK064SA on the NQPACK064SA160.
4 Attach the tip of the probe of the emulator to the M38D29T2-RLFS, and connect the M38D29T2-RLFS and YQPACK064SA.
(2) For M38D29T2-RLFS-HP
1 Mount the NQPACK064SD-ND to the foot pattern of the user system.
2 Attach the included M3T-F160-64NSD to the M38D29T2-RLFS.
3 Mount the YQPACK064SD on the NQPACK064SD-ND.
4 Attach the tip of the probe of the emulator to the M38D29T2-RLFS, and connect the M38D29T2-RLFS and YQPACK064SD.
Emulator
Emulator
(4)
(4)
M38D29T2 - RLFS
M38D29T2 - RLFS
(2)
(2)
M3T-F160-64NSD
M3T-F160- 64 NSA
(4)
(4)
YQ- GUIDE (x4)
YQPACK064SD
YQ - GUIDE(x4)
YQPACK064 SA
(3)
(3)
NQPACK 064SD - ND
NQPACK 064SA160
(1)
(1)
PLQP 0064 KB - A ( 64P6Q-A)
64-pin 0.5mm pitch
foot pattern
PLQP0064GA- A (64P6U-A)
64-pin 0.8mm pitch
foot pattern
●: No. 1 pin
●: No. 1 pin
Be sure to align the pins.
Be sure to align the pins.
Figure 3 Connection procedure of M38D29T2-RLFS-FP
Figure 4 Connection procedure of M38D29T2-RLFS-HP
6. External Dimensions
64.0
R1
RESET GND
VCC
+
C5
R6 R5
C6
Figure 5 External dimensions
(3/4)
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Oscillator Circuit
This product has two oscillator circuit patterns for the main clock XIN and sub-clock XCIN. Figures 6 and 7 show the oscillator
circuit diagram and oscillator circuit pattern, respectively. Select one of them according to the oscillator circuitry of the user system.
(1) When using the internal oscillator circuit of the MCU:
The oscillator circuit on the user system may not oscillate because a converter board is used between the emulator MCU and the
user system. In this case, set the jumper switch to INT and mount an oscillator circuit on the M38D29T2-RLFS’s oscillator
circuit pattern. When using the oscillator circuit on the user system, be sure to set the jumper switch to EXT.
(2) When using an oscillator module IC etc. (self-oscillation):
It is not necessary to mount an oscillator circuit on the M38D29T2-RLFS’s oscillator circuit pattern.
TP 2
TP3
TP1
GND
VCC RESET
+
C5
IC1
CN1,CN2
VCC
CN2 -5b (VCC)
R 1
RESET*
Vref
CN2 -2b (RESET*)
CN1 - 12a ( Vref )
C6
AVss
CN1 - 12b ( AVss)
XCIN
XCOUT
XIN
XOUT
CN2 -3b (P61/ Xcin )
CN2 -3a (P62/ Xcout)
CN2 -4b ( Xin )
CN2 -5a ( Xout)
JP3
JP4
JP1
JP2
EXT
EXT
EXT
INT
EXT
CN2 -4a ( Vss)
INT
INT
INT
R3
R4
C4
R2
X2
X1
C3
C1
C 2
Figure 6 Oscillator circuit diagram
JP1 XIN
INT
JP2 XOUT
INT
JP3 XCIN
INT
JP4 XCOUT
EXT
EXT
R2
EXT
C3
INT
EXT
X1
For 2-terminal oscillator
For 3-terminal oscillator
X2
R3
R4
C1
C2
C4
Figure 7 Oscillator circuit pattern
8. Precautions
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
z When using the oscillator circuit on the M38D29T2-RLFS, check the output waveform of pins Xout and Xcout by
an oscilloscope.
z When mounting an oscillator circuit on the M38D29T2-RLFS, make sure that 2 mm or more of a DIP pin does not
appear on the rear face (solder side). It may be short-circuited with the DIP pin of the converter board.
z For inquiries about the product or the contents of this manual, contact your local distributor.
Renesas Tools Homepage
(4/4)
Download from Www.Somanuals.com. All Manuals Search And Download.
|