To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions
Keep safety first in your circuit designs!
1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corporation product best suited to the customer's application; they do not convey any
license under any intellectual property rights, or any other rights, belonging to Renesas Technology
Corporation or a third party.
2. Renesas Technology Corporation assumes no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corporation without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corporation
or an authorized Renesas Technology Corporation product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corporation assumes no responsibility for any damage, liability, or other loss
rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corporation by various
means, including the Renesas Technology Corporation Semiconductor home page
(http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams,
charts, programs, and algorithms, please be sure to evaluate all information as a total system before
making a final decision on the applicability of the information and products. Renesas Technology
Corporation assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device
or system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor
when considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be
exported under a license from the Japanese government and cannot be imported into a country other
than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corporation for further details on these materials or the products
contained therein.
Download from Www.Somanuals.com. All Manuals Search And Download.
H8S/2378F E10A Emulator
User’s Manual
ADE-702-359
Rev. 1.0
10/18/02
Hitachi, Ltd.
HS2378KCM01HE
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s
patent, copyright, trademark, or other intellectual property rights for information contained in
this document. Hitachi bears no responsibility for problems that may arise with third party’s
rights, including intellectual property rights, in connection with use of the information
contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you
have received the latest product standards or specifications before final design, purchase or
use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability.
However, contact Hitachi’s sales office before using the product in an application that
demands especially high quality and reliability or where its failure or malfunction may directly
threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear
power, combustion control, transportation, traffic, safety equipment or medical equipment for
life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi
particularly for maximum rating, operating supply voltage range, heat radiation characteristics,
installation conditions and other characteristics. Hitachi bears no responsibility for failure or
damage when used beyond the guaranteed ranges. Even within the guaranteed ranges,
consider normally foreseeable failure rates or failure modes in semiconductor devices and
employ systemic measures such as fail-safes, so that the equipment incorporating Hitachi
product does not cause bodily injury, fire or other consequential damage due to operation of
the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document
without written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi
semiconductor products.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
Emulator Product:
Throughout this document, the term "emulator product" shall be defined as the following
products produced only by Hitachi, Ltd. excluding all subsidiary products.
•
•
Emulator
User system interface cable
The user system or a host computer is not included in this definition.
Purpose of the Emulator Product:
This emulator product is a software and hardware development tool for systems employing the
Hitachi microcomputer. This emulator product must only be used for the above purpose.
Limited Applications:
This emulator product is not authorized for use in MEDICAL, atomic energy, aeronautical or
space technology applications without consent of the appropriate officer of a Hitachi sales
company. Such use includes, but is not limited to, use in life support systems. Buyers of this
emulator product must notify the relevant Hitachi sales offices before planning to use the product
in such applications.
Improvement Policy:
Hitachi, Ltd. (including its subsidiaries, hereafter collectively referred to as Hitachi) pursues a
policy of continuing improvement in design, performance, and safety of the emulator product.
Hitachi reserves the right to change, wholly or partially, the specifications, design, user's manual,
and other documentation at any time without notice.
Target User of the Emulator Product:
This emulator product should only be used by those who have carefully read and thoroughly
understood the information and restrictions contained in the user's manual. Do not attempt to use
the emulator product until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the emulator product.
I
Download from Www.Somauals Search And Download.
LIMITED WARRANTY
Hitachi warrants its emulator products to be manufactured in
accordance with published specifications and free from defects in
material and/or workmanship. Hitachi, at its option, will replace any
emulator products returned intact to the factory, transportation charges
prepaid, which Hitachi, upon inspection, shall determine to be defective
in material and/or workmanship. The foregoing shall constitute the sole
remedy for any breach of Hitachi's warranty. See the Hitachi warranty
booklet for details on the warranty period. This warranty extends only
to you, the original Purchaser. It is not transferable to anyone who
subsequently purchases the emulator product from you. Hitachi is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
HITACHI MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL HITACHI BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
EMULATOR PRODUCT, THE USE OF ANY EMULATOR
PRODUCT, OR ITS DOCUMENTATION, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS
EXPRESSLY STATED OTHERWISE IN THIS WARRANTY,
THIS EMULATOR PRODUCT IS SOLD "AS IS ", AND YOU
MUST ASSUME ALL RISK FOR THE USE AND RESULTS
OBTAINED FROM THE EMULATOR PRODUCT.
II
Download from Www.Somauals Search And Download.
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Hitachi shall have no liability or legal responsibility for any problems caused by misuse, abuse,
misapplication, neglect, improper handling, installation, repair or modifications of the emulator
product without Hitachi's prior written consent or any problems caused by the user system.
All Rights Reserved:
This user's manual and emulator product are copyrighted and all rights are reserved by Hitachi.
No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-
copy or machine-readable form, by any means available without Hitachi's prior written consent.
Other Important Things to Keep in Mind:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Hitachi's semiconductor products. Hitachi assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Hitachi.
Figures:
Some figures in this user's manual may show items different from your actual system.
MCU names:
This user’s manual uses H8S/xxxx as an example of the MCU names.
Limited Anticipation of Danger:
Hitachi cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the emulator product are therefore not all inclusive.
Therefore, you must use the emulator product safely at your own risk.
III
Download from Www.Somauals Search And Download.
SAFETY PAGE
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
DEFINITION OF SIGNAL WORDS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE emphasizes essential information.
IV
Download from Www.Somauals Search And Download.
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Connect the connectors in the user system and in the
user interface cable by confirming the correct direction.
4. If the E10A emulator PCMCIA and PCI cards are mounted
on the same host computer, the connectors may be
illegally connected.
V
Download from Www.Somauals Search And Download.
Warnings on Emulator Usage
Be sure to read and understand the warnings below before using this emulator. Note that these are
the main warnings, not the complete list.
WARNING
Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or PARTS.
Failure to do so will result in a FIRE HAZARD and will
damage the user system and the emulator product or will
result in PERSONAL INJURY. The USER PROGRAM will be
LOST.
CAUTION
Place the host computer and user system so that no
cable is bent or twisted. A bent or twisted cable will impose
stress on the user interface leading to connection or contact
failure.
Make sure that the host computer and the user system
are placed in a secure position so that they do not move
during use nor impose stress on the user interface.
VI
Download from Www.Somauals Search And Download.
CAUTION
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
VII
Download from Www.Somauals Search And Download.
VIII
Download from Www.Somauals Search And Download.
Preface
Thank you for purchasing the E10A emulator.
CAUTION
READ section 2, Preparation before Use, of this User’s
Manual before using the emulator product. Incorrect
operation will damage the user system and the emulator
product.
This emulator is an efficient development tool for software and hardware of user systems based on
Hitachi’s original microprocessor. The emulator operates using the Hitachi debugging interface
(hereafter referred to as the HDI), which is the interface program that runs on Microsoft
Windows 98, Microsoft Windows Me, Microsoft Windows NT , or Microsoft Windows
2000, operating system.
This manual describes the functions and operating procedures of the E10A emulator. Sections 1 to
5 describe common features of all types of E10A emulators. Section 6 describes supplements to
the E10A emulator.
This manual consists of six sections. The information contained in each section is summarized
below:
Section 1, Overview, gives the emulator overview.
•
•
Section 2, Preparation before Use, gives instructions for first-time users, such as preparation
before use and system connection.
Section 3, Tutorial, describes HDI operating examples.
•
•
•
Section 4, Descriptions of Windows, describes HDI windows for operating the emulator.
Section 5, Command-line Functions describes how to input HDI commands and command
types.
Section 6, H8S/xxxx E10A Emulator Specifications describes the features of the E10A
emulator for each MCU. Section 7 describes the important information of the E10A emulator
according to emulator products. Read these sections before using the E10A emulator.
•
The HDI installation disks are provided by the CD-R. Refer to the descriptions in the manuals of
the host computer or operating system.
i
Download from Www.Somauals Search And Download.
Related Manuals:
•
•
•
•
•
Supplementary Informations
Hitachi Debugging Interface User's Manual (HS6400DIIW5SE)
H8S, H8/300 Series C/C++ Compiler, Assembler, Optimizing Linkage Editor User's Manual
Hardware Manual for each MCU
Programming Manual for each MCU
Notes: 1. IBM PC is a registered trademark of International Business Machines
Corporation.
2. Microsoft®, Windows®, and Windows NT® are registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Microsoft® Windows® 98 operating system is referred to as Windows® 98 in this
user's manual.
Microsoft® Windows® Millennium Edition operating system is referred to as
Windows® Me in this user's manual.
Microsoft® Windows NT® operating system is referred to as Windows NT® in
this user's manual.
Microsoft® Windows® 2000 operating system is referred to as Windows® 2000 in
this user's manual.
ii
Download from Www.Somauals Search And Download.
Contents
Section 1 Overview........................................................................................... 1
1.1 Warnings...........................................................................................................................3
1.2 Environmental Conditions ................................................................................................4
1.3 Components ......................................................................................................................6
Section 2 Preparation before Use....................................................................... 7
2.1 Emulator Preparation ........................................................................................................7
2.2 HDI Installation.................................................................................................................8
2.2.1 Installing under Windows 98 and Windows Me Operating Systems................8
2.2.2 Installing under Windows NT 4.0 Operating System.........................................9
2.2.3 Installing under Windows 2000 Operating System ............................................10
2.3 Connecting the Host Computer with the Card Emulator ..................................................11
2.4 Connecting the Card Emulator with the User System.......................................................12
2.5 System Check....................................................................................................................14
2.5.1 H8S/xxxx E10A Emulator Mode...........................................................................17
2.5.2 Writing H8S/xxxx E10A Flash memory Mode......................................................20
2.6 Ending the HDI.................................................................................................................23
2.7 Uninstalling the HDI.........................................................................................................24
Section 3 Tutorial............................................................................................... 25
3.1 Introduction.......................................................................................................................25
3.2 Running the HDI...............................................................................................................26
3.3 [HDI] Window..................................................................................................................27
3.4 Setting up the Emulator.....................................................................................................28
3.5 Setting the [Configuration] Dialog Box............................................................................28
3.6 Downloading the Tutorial Program ..................................................................................30
3.6.1 Downloading the Tutorial Program .....................................................................30
3.6.2 Displaying the Source Program ...........................................................................31
3.7 Setting the Software Breakpoint .......................................................................................33
3.8 Setting Registers ...............................................................................................................34
3.9 Executing the Program......................................................................................................36
3.10 Reviewing Breakpoints.....................................................................................................39
3.11 Viewing Memory..............................................................................................................40
3.12 Watching Variables...........................................................................................................41
3.13 Stepping Through a Program............................................................................................44
3.13.1 Executing [Step In] Command.............................................................................45
3.13.2 Executing [Step Out] Command..........................................................................46
3.13.3 Executing [Step Over] Command........................................................................48
3.14 Displaying Local Variables...............................................................................................50
iii
Download from Www.Somauals Search And Download.
3.15 Break Function..................................................................................................................51
3.15.1 Software Break Function .....................................................................................51
3.16 Hardware Break Function.................................................................................................57
3.17 Trace Function ..................................................................................................................64
3.18 What Next? .......................................................................................................................65
Section 4 Descriptions of Windows....................................................................67
4.1 HDI Windows...................................................................................................................67
4.2 Descriptions of Each Window ..........................................................................................70
4.2.1 [Configuration] Dialog Box.................................................................................70
4.2.2 [E10A Driver Details] Dialog Box ......................................................................75
4.2.3 [Breakpoints] Window.........................................................................................76
4.2.4 [Break] Dialog Box..............................................................................................78
4.2.5 [Breakpoint] Dialog Box .....................................................................................84
4.2.6 [Break condition] Dialog Box..............................................................................86
4.2.7 [Break condition] Dialog Box Pages ...................................................................88
4.2.8 [Trace] Window...................................................................................................92
4.2.9 [System Status] Window......................................................................................94
Section 5 Command-line Functions....................................................................97
5.1 Table and Symbol Description..........................................................................................97
5.1.1 Format..................................................................................................................97
5.1.2 Parameter Input....................................................................................................97
5.1.3 Examples..............................................................................................................98
5.1.4 Related Items .......................................................................................................98
5.2 Command Descriptions.....................................................................................................99
5.2.1 BREAKCONDITION_CLEAR: BCC.................................................................100
5.2.2 BREAKCONDITION_DISPLAY: BCD.............................................................101
5.2.3 BREAKCONDITION_ENABLE: BCE ..............................................................102
5.2.4 BREAKCONDITION_SET: BCS .......................................................................103
5.2.5 BREAKPOINT: BP .............................................................................................106
5.2.6 BREAKPOINT_CLEAR: BC..............................................................................107
5.2.7 BREAKPOINT_DISPLAY: BD..........................................................................108
5.2.8 BREAKPOINT_ENABLE: BE ...........................................................................109
5.2.9 DEVICE_TYPE: DE ...........................................................................................110
5.2.10 GO_OPTION: GP................................................................................................111
5.2.11 JTAG_CLOCK: JCK...........................................................................................112
5.2.12 REFRESH: RF.....................................................................................................114
5.2.13 RESET: RE..........................................................................................................115
5.2.14 STATUS: STS .....................................................................................................116
5.2.15 STEP_INTERRUPT: SI.......................................................................................117
5.2.16 TRACE_DISPLAY: TD ......................................................................................118
iv
Download from Www.Somauals Search And Download.
Section 6 H8S/2378F E10A Emulator Specifications........................................ 119
6.1 Overview of the Emulator.................................................................................................119
6.2 Pin Arrangement of the Hitachi-UDI Port Connector.......................................................120
6.3 Differences between the MCUs and the Emulator............................................................125
6.4 The H8S/2378F E10A Emulator Functions ......................................................................126
6.4.1 Emulator Driver Selection ...................................................................................126
6.4.2 Hardware Break Functions...................................................................................126
6.4.3 Notes on Setting the [Breakpoint] Dialog Box ....................................................128
6.4.4 Trace Function .....................................................................................................129
6.4.5 Notes on HDI.......................................................................................................140
v
Download from Www.Somauals Search And Download.
Figures
Figure 1.1 System Configuration with the Emulator (PCMCIA Card Emulator Used) ............1
Figure 1.2 System Configuration with the Emulator (PCI Card Emulator Used) .....................2
Figure 2.1 Emulator Preparation Flow Chart.............................................................................7
Figure 2.2 Inserting the PCMCIA Card Emulator into the Host Computer...............................11
Figure 2.3 Inserting the PCI Card Emulator into the Host Computer........................................11
Figure 2.4 Connecting the User System Interface Cable to the User System............................12
Figure 2.5 [Start] Menu .............................................................................................................14
Figure 2.6 [Select Session] Dialog Box.....................................................................................15
Figure 2.7 [E10A Driver Details] Dialog Box...........................................................................16
Figure 2.8 [System Clock] Dialog Box .....................................................................................17
Figure 2.9 [ID Code] Dialog Box..............................................................................................17
Figure 2.10 [HDI] Status Bar.....................................................................................................17
Figure 2.11 [H-UDI Connector Disconnected] Dialog Box ......................................................18
Figure 2.12 [Can not find /RESET signal] Dialog Box.............................................................18
Figure 2.13 [Check the connection] Dialog Box .......................................................................19
Figure 2.14 [COMMUNICATION TIMEOUT ERROR] Dialog Box......................................19
Figure 2.15 [INVALID ASERAM FIRMWARE!] Dialog Box................................................19
Figure 2.16 [Unable to restore the previous driver settings] Dialog Box..................................20
Figure 2.17 [System Clock] Dialog Box ...................................................................................20
Figure 2.18 [Load Program] Dialog Box...................................................................................21
Figure 2.19 Checksum Value after Downloading the Program.................................................21
Figure 2.20 [HDI] Dialog Box...................................................................................................21
Figure 2.21 [Continue?] Window..............................................................................................22
Figure 2.22 [Connector disconnected] Dialog Box ...................................................................22
Figure 2.23 [Flash memory erase error!] Dialog Box ...............................................................22
Figure 2.24 [Exit HDI] Dialog Box...........................................................................................23
Figure 2.25 [Save session] Dialog Box .....................................................................................23
Figure 3.1 [Start] Menu .............................................................................................................26
Figure 3.2 [HDI] Window .........................................................................................................27
Figure 3.3 [Configuration] Dialog Box .....................................................................................28
Figure 3.4 [Load Program] Dialog Box.....................................................................................30
Figure 3.5 [HDI] Dialog Box.....................................................................................................30
Figure 3.6 [Open] Dialog Box...................................................................................................31
Figure 3.7 [Program] Window (Displaying the Source Program).............................................32
Figure 3.8 [Program] Window (Setting a Software Breakpoint)...............................................33
Figure 3.9 [Registers] Window..................................................................................................34
Figure 3.10 [Register] Dialog Box (PC)....................................................................................34
Figure 3.11 [Register] Dialog Box (ER7)..................................................................................35
Figure 3.12 [Go] Button ............................................................................................................36
Figure 3.13 [Reset Go] Button...................................................................................................36
vi
Download from Www.Somauals Search And Download.
Figure 3.14 [Program] Window (Break Status).........................................................................36
Figure 3.15 [System Status] Window........................................................................................37
Figure 3.16 [Breakpoints] Window ...........................................................................................39
Figure 3.17 [Open Memory Window] Dialog Box....................................................................40
Figure 3.18 [Memory] Window.................................................................................................40
Figure 3.19 [Instant Watch] Dialog Box....................................................................................41
Figure 3.20 [Watch] Window (Displaying the Array)...............................................................42
Figure 3.21 [Add Watch] Dialog Box .......................................................................................42
Figure 3.22 [Watch] Window (Displaying the Variable) ..........................................................43
Figure 3.23 [Watch] Window (Displaying Array Elements).....................................................43
Figure 3.24 [Step In] Button......................................................................................................45
Figure 3.25 [Program] Window (Step In)..................................................................................45
Figure 3.26 [Step Out] Button ...................................................................................................46
Figure 3.27 [Program] Window (Step Out)...............................................................................46
Figure 3.28 [Program] Window (Step In −> Step In)................................................................47
Figure 3.29 [Program] Window (Before Step Over Execution) ................................................48
Figure 3.30 [Step Over] Button .................................................................................................48
Figure 3.31 [Program] Window (Step Over).............................................................................49
Figure 3.32 [Locals] Window....................................................................................................50
Figure 3.33 [Breakpoints] Window (Before Software Breakpoint Setting)...............................51
Figure 3.34 [Point] Page ([Break] Dialog Box).........................................................................52
Figure 3.35 [Breakpoint] Dialog Box........................................................................................53
Figure 3.36 [Point] Page ([Break] Dialog Box) (After Software Breakpoint Setting) ..............54
Figure 3.37 [Breakpoints] Window (Software Breakpoint Setting) ..........................................55
Figure 3.38 [Program] Window at Execution Stop (Software Break).......................................55
Figure 3.39 Displayed Contents of the [System Status] Window (Software Break) .................56
Figure 3.40 [Breakpoints] Window (Before Hardware Break Condition Setting) ....................57
Figure 3.41 [Condition] Page ([Break] Dialog Box) .................................................................58
Figure 3.42 [condition] Page ([Break condition 1] Dialog Box)...............................................59
Figure 3.43 [Break] Dialog Box (After Hardware Break Condition Setting)............................60
Figure 3.44 [Breakpoints] Window ([Break condition 1] Setting) ............................................61
Figure 3.45 [Program] Window at Execution Stop (Break condition 1) ...................................62
Figure 3.46 Displayed Contents of the [System Status] Window (Break condition 1)..............63
Figure 3.47 [Trace] Window .....................................................................................................64
Figure 4.1 [Configuration] Dialog Box .....................................................................................70
Figure 4.2 [General] Page ([Configuration] Dialog Box)..........................................................72
Figure 4.3 Warning Message Box .............................................................................................74
Figure 4.4 [E10A Driver Details] Dialog Box...........................................................................75
Figure 4.5 [Breakpoints] Window .............................................................................................76
Figure 4.6 [Break] Dialog Box ..................................................................................................78
Figure 4.7 [Point] Page ([Break] Dialog Box)...........................................................................80
Figure 4.8 [Condition] Page ([Break] Dialog Box) ...................................................................82
Figure 4.9 [Breakpoint] Dialog Box..........................................................................................84
vii
Download from Www.Somauals Search And Download.
Figure 4.10 [Break condition 1] Dialog Box.............................................................................86
Figure 4.11 [condition] Page .....................................................................................................89
Figure 4.12 [Trace] Window .....................................................................................................92
Figure 4.13 [System Status] Window........................................................................................94
Figure 6.1 Pin Arrangement of the Hitachi-UDI Port Connector..............................................120
Figure 6.2 Example of Emulator Connection............................................................................121
Figure 6.3 Connection of Emulator ...........................................................................................122
Figure 6.4 EMLE Pin and Emulator..........................................................................................122
Figure 6.5 Connection of #RES Pin ..........................................................................................123
Figure 6.6 Interface Circuit in the Emulator (Reference Figure)...............................................123
viii
Download from Www.Somauals Search And Download.
Tables
Table 1.1 Environmental Conditions.........................................................................................4
Table 1.2 Operating Environments............................................................................................5
Table 2.1 Recommended Connector..........................................................................................12
Table 3.1 Tutorial Program: Configuration and Parts ...............................................................25
Table 3.2 Setting the [Configuration] Dialog Box.....................................................................29
Table 3.3 Contents of the [System Status] Window ..................................................................38
Table 3.4 Step Option................................................................................................................44
Table 4.1 HDI Window Menus and Related Manual Entries ....................................................67
Table 4.2 [Configuration] Dialog Box Page..............................................................................71
Table 4.3 [General] Page Options..............................................................................................73
Table 4.4 [E10A Driver Details] Dialog Box Option ................................................................75
Table 4.5 [Breakpoints] Window Display Items .......................................................................77
Table 4.6 [Breakpoints] Window Pop-up Menu Operation.......................................................77
Table 4.7 [Break] Dialog Box Pages .........................................................................................79
Table 4.8 [Point] Page Options..................................................................................................81
Table 4.9 [Condition] Page Options ..........................................................................................83
Table 4.10 [Address] Page Options ...........................................................................................85
Table 4.11 Setting Conditions in [Break condition] Dialog Box...............................................88
Table 4.12 [Break condition] Dialog Box Pages .......................................................................88
Table 4.13 [Address] Group Box Options.................................................................................90
Table 4.14 Radio Button Options ..............................................................................................90
Table 4.15 [Data] Group Box Options.......................................................................................90
Table 4.16 [Read/Write] Group Box Options............................................................................91
Table 4.17 [Trace] Window Display Items................................................................................93
Table 4.18 [System Status] Window Display Items ..................................................................95
Table 5.1 E10A HDI Commands...............................................................................................99
Table 5.2 BREAKCONDITION_CLEAR Command Parameter ..............................................100
Table 5.3 BREAKCONDITION_DISPLAY Command Parameter ..........................................101
Table 5.4 BREAKCONDITION_ENABLE Command Parameter ...........................................102
Table 5.5 BREAKCONDITION_SET Command Parameters ..................................................104
Table 5.6 BREAKPOINT Command Parameter .......................................................................106
Table 5.7 BREAKPOINT_CLEAR Command Parameter ........................................................107
Table 5.8 BREAKPOINT_DISPLAY Command Parameter.....................................................108
Table 5.9 BREAKPOINT_ENABLE Command Parameters ....................................................109
Table 5.10 DEVICE_TYPE Command Parameter....................................................................110
Table 5.11 GO_OPTION Command Parameter ........................................................................111
Table 5.12 JTAG_CLOCK Command Parameter .....................................................................112
Table 5.13 REFRESH Command Parameter .............................................................................114
Table 5.14 RESET Command Parameter ..................................................................................115
Table 5.15 STATUS Command Parameter ...............................................................................116
Table 5.16 STEP_INTERRUPT Command Parameter .............................................................117
ix
Download from Www.Somauals Search And Download.
Table 5.17 TRACE_DISPLAY Command Parameter...............................................................118
Table 6.1 Components of the Emulator (HS2378KCM01H or HS2378KCI01H) ....................119
Table 6.2 Unavailable Pin Functions.........................................................................................124
Table 6.3 Register Initial Values at Emulator Power-On ..........................................................125
Table 6.4 Type Name and Driver ..............................................................................................126
Table 6.5 Hardware Break Condition Specification Items ........................................................126
Table 6.6 Conditions Set in [Break condition] Dialog Box.......................................................127
Table 6.7 Conditions Set by BREAKCONDITION_SET Command........................................127
Table 6.8 Setting Trace Acquisition ..........................................................................................129
Table 6.9 Items in the [Trace] Window.....................................................................................130
Table 6.10 Trace Search Function.............................................................................................131
Table 6.11 [Address] Group Box Options.................................................................................131
Table 6.12 [Data] Group Box Options ......................................................................................131
Table 6.13 [Bus status] Group Box Options..............................................................................132
Table 6.14 [Area] Group Box Options ......................................................................................132
Table 6.15 [Read/Write] Group Box Options............................................................................132
Table 6.16 [IRQ] Group Box Options .......................................................................................132
Table 6.17 Commands for the Trace Function ..........................................................................133
Table 6.18 TRACE_DISPLAY Command Parameter...............................................................133
Table 6.19 TRACE_MODE Command Parameter....................................................................135
Table 6.20 TRACE_SEARCH Command Parameter................................................................138
x
Download from Www.Somauals Search And Download.
Section 1 Overview
The E10A emulator (hereafter referred to as the emulator) is a software and hardware
development support tool for application systems using the microprocessor developed by Hitachi,
Ltd.
The PCMCIA card emulator or PCI card emulator (hereafter referred to as the card emulator),
which is the main unit of the emulator, is connected, through the Hitachi-UDI (user debug
*
interface) port , to the user system. The user system can be debugged under the conditions similar
to the actual application conditions. The emulator enables debugging anywhere indoors or out.
The host computer for controlling the emulator must be an IBM PC compatible machine with a
PCMCIA type II or PCI slot.
Figures 1.1 and 1.2 show the system configuration using the emulator.
Note: The Hitachi-UDI is an interface compatible with the Joint Test Action Group
(JTAG) specifications.
Host computer (PC with PCMCIA TYPE II slot)
PCMCIA card emulator
User system interface cable
PC
PC
Card
H8S/xxxx
Insert into the PCMCIA TYPE II slot
Connect to the Hitachi-UDI port connector
User system
Figure 1.1 System Configuration with the Emulator (PCMCIA Card Emulator Used)
1
Download from Www.Somauals Search And Download.
User system interface cable
PCI card emulator
H8S/xxxx
Insert into
the PCI slot
User system
Host computer
(PC with PCI slot)
Figure 1.2 System Configuration with the Emulator (PCI Card Emulator Used)
The emulator provides the following features:
•
•
Excellent cost-performance card emulator
Compactness and low price are implemented using the PCMCIA interface or the PCI interface.
Realtime emulation
Realtime emulation of the user system is enabled at the maximum operating frequency of the
CPU.
•
•
Excellent operability
Using the Hitachi Debugging Interface (HDI) on the Microsoft® Windows® 98, Microsoft®
Windows® Me, Microsoft® Windows NT®, and Microsoft® Windows® 2000 operating systems
enable user program debugging using a pointing device such as a mouse. The HDI enables
high-speed downloading of load module files.
Various debugging functions
Various break and trace functions enable efficient debugging. Breakpoints and break
conditions can be set by the specific window, trace information can be displayed on a window,
and command-line functions can be used.
•
•
•
Memory access during emulation
During emulation, the memory contents can be read and modified.
Debugging of the user system in the final development stage
The user system can be debugged under conditions similar to the actual application conditions.
Compact debugging environment
When the card emulator specific to the PCMCIA interface is used, a laptop computer can be
used as a host computer, creating a debugging environment in any place.
2
Download from Www.Somauals Search And Download.
1.1
Warnings
CAUTION
READ the following warnings before using the emulator
product. Incorrect operation will damage the user system and
the emulator product. The USER PROGRAM will be LOST.
1. Check all components against the component list after unpacking the emulator.
2. Never place heavy objects on the casing.
3. Protect the emulator from excessive impacts and stresses. For details, refer to section 1.2,
Environmental Conditions.
4. Do not insert the emulator into any slot (PCMCIA TYPE II slot or PCI slot) other than the
specified one.
5. When moving the host computer or user system, take care not to vibrate or damage it.
6. After connecting the cable, check that it is connected correctly. For details, refer to section 2,
Preparation before Use.
7. Supply power to the connected equipment after connecting all cables. Cables must not be
connected or removed while the power is on.
3
Download from Www.Somauals Search And Download.
1.2
Environmental Conditions
CAUTION
Observe the conditions listed in tables 1.1 and 1.2 when
using the emulator. Failure to do so will damage the user
system and the emulator product. The USER PROGRAM will
be LOST.
Table 1.1 Environmental Conditions
Item
Specifications
Temperature
Operating: +10°C to +35°C
Storage: –10°C to +50°C
Humidity
Vibration
Operating: 35% RH to 80% RH, no condensation
Storage: 35% RH to 80% RH, no condensation
Operating:
Storage:
2.45 m/s2 max.
4.9 m/s2 max.
Transportation: 14.7 m/s2 max.
Ambient gases There must be no corrosive gases present
Table 1.2 lists the acceptable operating environments.
4
Download from Www.Somauals Search And Download.
Table 1.2 Operating Environments
Item
Description
Host computer
Built-in Pentium or higher-performance CPU (200 MHz or higher
recommended); IBM PC or compatible machine with the PCMCIA
TYPE II slot or the PCI slot.
OS
Windows® 98, Windows® Me, Windows NT®, or Windows® 2000
Minimum memory
capacity
32 Mbytes or more (double of the load module size recommended)
Hard-disk capacity
Installation disk capacity: 10 Mbytes or more. (Prepare an area at
least double the memory capacity (four-times or more recommended)
as the swap area.)
Pointing device such as
mouse
Connectable to the host computer; compatible with Windows® 98,
Windows® Me, Windows NT®, and Windows® 2000.
Power voltage
5.0 ± 0.25 V
Current consumption
HS0005KCM05H: 60 mA (max)
HS0005KCI05H: 55 mA (max)
CD-ROM drive
Required to install the emulator or refer to the emulator user’s manual.
5
Download from Www.Somauals Search And Download.
1.3
Components
Check all the components unpacking. For details on the E10A emulator components, refer to
section 6.1, Components of the Emulator. If the components are not complete, contact a Hitachi
sales agency.
6
Download from Www.Somauals Search And Download.
Section 2 Preparation before Use
2.1
Emulator Preparation
WARNING
READ the reference sections shaded in figure 2.1 before
using the emulator product. Incorrect operation will damage
the user system and the emulator product. The USER
PROGRAM will be LOST.
Unpack the emulator and prepare it for use as follows:
Reference
Unpack the emulator
Component list
Section 2.2
Check the components against the component list
Turn on the host computer
When the emulator
is used first.
Install the HDI
Turn off the host computer
Insert the card emulator into the host computer
and connect the emulator to the user system
Section 2.3
Section 3
Turn on the host computer
When the emulator
is used for second
time or later.
Start the HDI
Turn on the user system
Figure 2.1 Emulator Preparation Flow Chart
7
Download from Www.Somauals Search And Download.
2.2
HDI Installation
When the CD-R is inserted in the host computer’s CD-ROM drive, the HDI installation wizard is
automatically activated (holding the Shift key down while the CD-R is inserted cancels this
automatic activation). To run the installation wizard when it has not been automatically activated,
execute Setup.exe from the root directory of the CD-R.
Follow the cues given by the installation wizard to install the HDI.
Since hardware settings are also made during installation, the installation procedure differs
according to the operating system or interface (PCI or PCMCIA) being used. Follow the
installation steps carefully according to the environment you are using.
2.2.1
Installing under Windows 98 and Windows Me Operating Systems
(1) When the emulator is a PCI card:
1. Install the HDI (when the component type has to be selected during installation, be sure to
select [PCI Card Driver]).
2. Shut the operating system down and turn off the power to the host computer.
3. Insert the PCI-card emulator in a slot on the host computer. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
4. Restart the host computer. The hardware is now recognized and the driver is automatically
installed.*
(2) When the emulator is a PCMCIA card:
1. Install the HDI (when the component type has to be selected during installation, be sure to
select [PC Card Driver (PCMCIA)]).
2. Insert the PCMCIA-card emulator in the host computer’s slot. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
3. The hardware is now recognized and the driver is automatically installed.*
Note: When [Add New Hardware Wizard] is displayed, select the [Search for the best driver for
your device. (Recommended)] radio button and then the [Specify a location] check box to
select the path to be searched for drivers. The location must be specified according to the
emulator type, as indicated below:
When using the PCI-card emulator: <Drive>:\DRIVERS\PCI\95
When using the PCMCIA-card emulator: <Drive>:\DRIVERS\PCMCIA\95
(<Drive> is the CD-ROM drive name.)
8
Download from Www.Somauals Search And Download.
2.2.2
Installing under Windows NT 4.0 Operating System
(1) When the emulator is a PCI card:
1. Shut the operating system down and turn off the power to the host computer.
2. Insert the PCI-card emulator in a slot on the host computer. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
3. Start the host computer and log-on with an administrator-level user name.
4. Install the HDI. (For a component, be sure to select [PCI Card Driver]. There is a check
box for selecting the type name of the product under the [PCI Card Driver] component.
Select the appropriate type name. If the correct name is not selected, the correct driver will
not be installed, and the emulator will not operate.)
5. Restart the host computer.
(2) When the emulator is a PCMCIA card:
1. Shut the operating system down and turn off the power to the host computer.
2. Insert the PCMCIA-card emulator in the host computer’s slot. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
3. Start the host computer and log-on with an administrator-level user name.
4. During HDI installation, the setting value should be checked beforehand because inquiries
are made about the resource used by the PCMCIA-card emulator.
Start the [Start] menu -> [Programs] -> [Administrative Tools (Common)] -> [Windows
NT Diagnostics], check the status of the IRQ, I/O port, and memory from the resource
panel, and determine the setting values that do not conflict with other devices. (The
following resources are used: IRQ: one channel, I/O port: H’F byte, and memory: H’4000
byte.)
5. Install the HDI. (For a component, be sure to select [PC Card Driver (PCMCIA)]. There is
a check box for selecting the type name of each product under the [PC Card Driver
(PCMCIA)] component. Select the appropriate type name. If the correct name is not
selected, the correct driver will not be installed and the emulator will not operate.)
6. Restart the host computer.
Note: The driver that has been selected in the [Drivers] component starts after the host computer
is initiated. If the host computer is initiated with the card disconnected or with the
incorrect driver installed, the driver cannot initiate and the service control manager
informs the system of an error. This, however, is not a problem.
9
Download from Www.Somauals Search And Download.
2.2.3
Installing under Windows 2000 Operating System
(1) When the emulator is a PCI card:
1. Log-on with an administrator-level user name.
2. Install the HDI. (When a component is selected, be sure to select [PCI Card Driver].)
3. Shut the operating system down and turn off the power to the host computer.
4. Insert the PCI-card emulator in a slot on the host computer. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
5. Restart the host computer and log-on with an administrator-level user name. The hardware
is now recognized and the driver is automatically installed.*
(2) When the emulator is a PCMCIA card:
1. Log-on with an administrator-level user name.
2. Install the HDI. (When a component is selected, be sure to select [PC Card Driver
(PCMCIA)].)
3. Insert the PCMCIA-card emulator in the host computer’s slot. Refer to section 2.3,
Connecting the Host Computer with the Card Emulator.
4. The hardware is now recognized and the driver is automatically installed.*
Note: When [Found New Hardware Wizard] is displayed, select the [Search for a suitable driver
for my device (recommended).] radio button and then the [Specify a location] check box
to select the path to be searched for drivers. The location must be specified according to
the emulator type, as indicated below:
When using the PCI-card emulator: <Drive>:\DRIVERS\PCI\2000
When using the PCMCIA-card emulator: <Drive>:\DRIVERS\PCMCIA\2000
(<Drive> is the CD-ROM drive name.)
10
Download from Www.Somauals Search And Download.
2.3
Connecting the Host Computer with the Card Emulator
Insert the card emulator into the PCMCIA TYPE II slot or the PCI slot of the host computer
(figures 2.2 and 2.3).
Note: Be sure to install the HDI before the card emulator is inserted.
Figure 2.2 Inserting the PCMCIA Card Emulator into the Host Computer
Figure 2.3 Inserting the PCI Card Emulator into the Host Computer
Use the procedure, described in section 2.4, to connect the emulator to the user system with the
user system interface cable, or to disconnect them when moving the emulator or the user system.
11
Download from Www.Somauals Search And Download.
Note: When installing the PCI card emulator, note the following:
1. Turn off the host computer.
2. Insert the emulator into the PCI slot in parallel.
3. Screw in the emulator after confirming the connector and cable positions.
2.4
Connecting the Card Emulator with the User System
(1) The connector must be installed to the user system. Table 2.1 shows the recommended
connector for the emulator.
Table 2.1 Recommended Connector
Type Number
Manufacturer
Specifications
2514-6002
3M Limited
14-pin straight type
Note: When the connector is used, do not install any components within 3 mm of the
connector.
(2) The pin arrangement of the connector is shown in section 6.2, Pin Arrangement of the Hitachi-
UDI Port Connector.
(3) Figure 2.4 shows how to connect the user system interface cable to the user system. Connect
the ground line of the cable to the user system ground. The end of the ground line has a hole
having a diameter of 3 mm, and therefore, when the ground line is screwed to the user system,
the screw diameter must be 3 mm.
Figure 2.4 Connecting the User System Interface Cable to the User System
12
Download from Www.Somauals Search And Download.
Notes: 1. To connect the signals output from the connector, refer to the MCU pin
alignment.
2. To remove the user system interface cable from the user system, pull the tab
on the connector upward.
3. The range of communications that the emulator operates at is different
according to the MCUs used.
4. Connect the signals from the connector as shown in section 6.2, Pin
Arrangement of the Hitachi-UDI Port Connector.
13
Download from Www.Somauals Search And Download.
2.5
System Check
When the HDI program is executed, check that the emulator operates correctly according to the
following procedure:
1. Check that the card emulator is inserted into the host computer.
2. Connect the user system interface cable to the connector of the card emulator.
3. Connect the user system interface cable to the Hitachi-UDI port connector.
4. Power on the host computer and select [HDI for E10A H8Sxxxx] -> [Hitachi Debugging
Interface] from the [Start] menu.
Figure 2.5 [Start] Menu
14
Download from Www.Somauals Search And Download.
5. Power on the user system and select the setting to be used.
Figure 2.6 [Select Session] Dialog Box
15
Download from Www.Somauals Search And Download.
6. The [E10A Driver Details] dialog box is displayed. With the [Driver] combo box, select the
driver to connect the HDI with the emulator. [Interface] displays the interface name of the PC
interface board to be connected, and [Channel] displays the interface to which the board is
connected. Once the driver is selected in the [E10A Driver Details] dialog box, this dialog
box is not displayed when the HDI is run next time. (This procedure will not be executed by
target MCUs.)
Figure 2.7 [E10A Driver Details] Dialog Box
•
•
With the [Driver] combo box, select the driver to connect the HDI with the emulator.
[Interface] displays the interface name of the card emulator to be connected, and [Channel]
displays the interface to which the board is connected.
[Driver] combo box: Select [E10A PC Card Driver 5] to use the PCMCIA card emulator.
Select [E10A PCI Card Driver 5] to use the PCI card emulator. For
details, refer to table 6.3 in section 6.4.1, Emulator Driver Selection.
[Interface] combo box: Select [PC Card] to use the PCMCIA card emulator.
Select [PCI] to use the PCI card emulator. (If the driver is not
installed, the [PC Card] or [PCI] is not displayed.)
•
Click the [Close] button.
16
Download from Www.Somauals Search And Download.
7. Supply power to the user system.
The subsequent procedures depend on the activation mode that was selected in step 5.
2.5.1 H8S/xxxx E10A Emulator Mode
This mode is used for debugging in the emulator.
1. After the [System Clock] window appears, input the system clock frequency. This frequency
value is used when writing and erasing flash memory in the emulator.
Figure 2.8 [System Clock] Dialog Box
2. Set an eight-digit hexadecimal ID code as a security code for the flash memory. Input this ID
code when [H8S/xxxx E10A Emulator] is selected and the [New registration] check box is
unselected on activating the HDI. If the ID code is not matched, the flash memory contents
are erased.
Figure 2.9 [ID Code] Dialog Box
3. When "Link up" appears on the status bar, the user and emulator programs have been
downloaded to the flash memory, and the HDI initialization is complete.
Figure 2.10 [HDI] Status Bar
17
Download from Www.Somauals Search And Download.
Notes: 1. When the HDI is not linked up even if the above procedure has been executed, the
driver will not be set correctly. Install drivers provided with the \SETUP
directory in the CD-R according to the screen instructions.
2. If the user system interface cable is disconnected to the Hitachi-UDI port
connector on the user system during user program execution, the following dialog
box will be displayed.
Figure 2.11 [H-UDI Connector Disconnected] Dialog Box
3. If the emulator is not initiated, the following dialog boxes shown in figures 2.12
through 2.15 will be displayed.
(a) If the following dialog box is displayed, the user system may not be turned on or
the RESET signal may not have been correctly input to the MCU. Check the
power supply and input circuit for the reset pin on the user system.
Figure 2.12 [Can not find /RESET signal] Dialog Box
18
Download from Www.Somauals Search And Download.
(b) If the following dialog box is displayed, check that the Hitachi-UDI port
connector on the user system is correctly connected.
Figure 2.13 [Check the connection] Dialog Box
(c) If the following dialog box is displayed, the MCU may not correctly operate.
Check if there are reasons for illegal MCU operation.
Figure 2.14 [COMMUNICATION TIMEOUT ERROR] Dialog Box
Figure 2.15 [INVALID ASERAM FIRMWARE!] Dialog Box
19
Download from Www.Somauals Search And Download.
4.
If the driver is not correctly connected, the following dialog box will be displayed.
Figure 2.16 [Unable to restore the previous driver settings] Dialog Box
The [E10A Driver Details] dialog box is displayed when the [OK] button is clicked.
Select the correct driver. For details, refer to section 6.4.1, Emulator Driver
Selection.
2.5.2 Writing H8S/xxxx E10A Flash memory Mode
In this mode the emulator is used as a flash memory writer. The following procedures apply when
[Writing H8S/xxxx E10A Flash memory] is selected from the activation modes listed in the
[Select Session] dialog box.
1. After the [System Clock] window appears, input the system clock frequency.
Figure 2.17 [System Clock] Dialog Box
20
Download from Www.Somauals Search And Download.
2. When the [Load Program] window appears, specify a user program to be downloaded. Click
the [Open] button to start downloading.
Figure 2.18 [Load Program] Dialog Box
3. When the program has been downloaded, the memory area that the checksum value and the
program code have been written appears.
Figure 2.19 Checksum Value after Downloading the Program
Figure 2.20 [HDI] Dialog Box
21
Download from Www.Somauals Search And Download.
4. The [Continue] window appears. When the [OK] button is clicked, a message is displayed to
request that power be supplied. Turn off the power, exchange the MCU, and supply power.
Repeat operations 1 to 3 until the [Exit] button is clicked. When the [Exit] button is clicked,
the HDI is terminated.
Figure 2.21 [Continue?] Window
Notes: 1. When the HDI does not link up, and the above procedures have been executed, the
driver setting must be incorrect. Install a driver from the \SETUP directory of
the CD-R according to the screen instructions.
2. If the user system interface cable is disconnected from the connector on the user
system, the following dialog box will appear.
Figure 2.22 [Connector disconnected] Dialog Box
3. If the emulator is not properly initialized, the following dialog box will appear.
If the following dialog box is displayed, the flash memory cannot be erased.
Exchange the MCU since the flash memory has been rewritten to more times than
the guaranteed value.
Figure 2.23 [Flash memory erase error!] Dialog Box
22
Download from Www.Somauals Search And Download.
2.6
Ending the HDI
Power off the emulator by using the following procedure:
1. Select [Exit] from the [File] menu to end the HDI. When the [Exit HDI] dialog box is
displayed, click the [Yes] button.
Figure 2.24 [Exit HDI] Dialog Box
2. Then, the [Save session] dialog box is displayed. If necessary, click the [Yes] button to save
session. After saving session, the HDI ends. If not necessary, click the [No] button to end the
HDI.
Figure 2.25 [Save session] Dialog Box
3. Turn the user system off.
23
Download from Www.Somauals Search And Download.
2.7
Uninstalling the HDI
Follow this procedure to remove the installed HDI from the user’s host computer.
1. Open [Add/Remove Programs Properties] from the control panel. Select the HDI program
from the list and click the [Add/Remove…] button.
2. The setup program is executed again and the installed application can be changed, modified,
or removed. When the application is to be uninstalled, select removal.
CAUTION
A shared file may be detected while the program is being
removed. If another HDI may be using the shared file, do not
remove the file. When Microsoft Windows NT 4.0 operating
system is used, the removal of the registry information on the
driver may be asked. If other HDI may use the target driver,
do not remove the registry information. If another HDI does
not start up after the removal process, re-install that HDI.
24
Download from Www.Somauals Search And Download.
Section 3 Tutorial
3.1
Introduction
The following describes the main functions of the emulator by using a tutorial program.
The tutorial program is based on the C program that sorts ten random data items in ascending or
descending order. The tutorial program performs the following actions:
•
•
•
The mainfunction generates random data to be sorted.
The sortfunction sorts the generated random data in ascending order.
The changefunction then sorts the data in descending order.
The tutorial program is included in the sort.cfile. The compiled load module is provided in
the Sysrof format and is included in the tutorial.absfile.
Table 3.1 lists the tutorial program configuration.
Table 3.1 Tutorial Program: Configuration and Parts
Item
Contents
Workspace for HEW V1.2
Load module
[Installation directory]\tutorial\tutorial.hws
[Installation directory]\tutorial\tutorial\Debug\tutorial.abs
[Installation directory]\tutorial\tutorial\tutorial.c
[Installation directory]\tutorial\tutorial\Debug\tutorial.sni
Main program (source file)
Stack information file
Notes: 1. This section describes general usage examples of the emulator. For each product
specifications, refer to section 6 or on-line help.
2. This program was created by using Hitachi Embedded Workshop (hereafter
referred to as HEW) V1.2. Older versions of HEW will not open the workspace
included with the package, so create a new workspace in such situations.
3. This program was compiled without optimization. If recompiled with different
settings, the addresses may differ from those given in this section.
4. tutorial.abs is a load module in the Dwarf2 format. If a load module is
recreated in the Sysrof format, the amount of information displayed on the HDI
screen during the program’s execution will be reduced.
5. This section describes general usage examples for the emulator. For the
specifications of particular products, refer to section 6 or the online help file.
25
Download from Www.Somauals Search And Download.
3.2
Running the HDI
To run the HDI, select [HDI for E10A H8Sxxxx] -> [Hitachi Debugging Interface] from the
[Start] menu.
Figure 3.1 [Start] Menu
For the procedure of running the HDI, refer to section 2.5, System Check.
26
Download from Www.Somauals Search And Download.
3.3
[HDI] Window
Figure 3.2 [HDI] Window
The key functions of the HDI are described in section 4, Descriptions of Windows. Numbers in
figure 3.2 indicate the following:
1. Menu bar: Gives the user access to the HDI commands for using the HDI debugger.
2. Toolbar: Provides convenient buttons as shortcuts for the most frequently used menu
commands.
3. Program window: Displays the source program being debugged.
4. Status bar: Displays the status of the emulator, and progress information about
downloading.
5. [Help] button: Activates on-line help about any features of the HDI user interface.
27
Download from Www.Somauals Search And Download.
3.4
Setting up the Emulator
The following MCU conditions must be set up on the emulator before downloading the program:
•
•
Device type
Execution mode
The following describes how to set up the emulator for the tutorial programs.
3.5
Setting the [Configuration] Dialog Box
•
Select [Configure Platform...] from the [Setup] menu to set configuration. The
[Configuration] dialog box is displayed.
Figure 3.3 [Configuration] Dialog Box
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
28
Download from Www.Somauals Search And Download.
Set options as follows:
Table 3.2 Setting the [Configuration] Dialog Box
Option
Value
Mode
H8S/xxxx (default)
Normal (normal execution, default)
Emulation mode
Step option (Disables interrupt during single step
execution)
Disables interrupts during single step
execution (default)
JTAG clock
4.125 MHz (default)
Operating Mode
Operating mode determined by setting the
mode pin (default)
Flash memory synchronization
Disable (default)
•
Click the [OK] button to set any changes in the configuration.
29
Download from Www.Somauals Search And Download.
3.6
Downloading the Tutorial Program
3.6.1
Downloading the Tutorial Program
Download the object program to be debugged.
•
Select [Load Program...] from the [File] menu. The [Load Program] dialog box is displayed.
Enter the [Offset] edit box and [File name] list box as shown in figure 3.4 and click the [Open]
button.
Figure 3.4 [Load Program] Dialog Box
When the file has been loaded, the following dialog box displays information about the
memory areas that have been filled with the program code.
Figure 3.5 [HDI] Dialog Box
•
Click the [OK] button to continue.
30
Download from Www.Somauals Search And Download.
3.6.2
Displaying the Source Program
The HDI allows the user to debug a program at the source level.
•
•
Select [Source...] from the [View] menu. The [Open] dialog box is displayed.
Select the C source file that corresponds to the object file the user has loaded.
Figure 3.6 [Open] Dialog Box
31
Download from Www.Somauals Search And Download.
•
Select [Sort.c] and click the [Open] button. The [Program] window is displayed.
Figure 3.7 [Program] Window (Displaying the Source Program)
•
If necessary, select the [Font...] option from the [Customize] submenu on the [Setup] menu to
select a clear font and size.
Initially the [Program] window shows the start of the main program, but the user can use the scroll
bar to scroll through the program to see the other statements.
32
Download from Www.Somauals Search And Download.
3.7
Setting the Software Breakpoint
A breakpoint is one of the easy debugging functions.
The [Program] window provides a very simple way of setting a software breakpoint at any point
in a program. For example, to set a breakpoint at the sortfunction call:
•
Select by double-clicking the [BP] column on the line containing the sortfunction call.
Figure 3.8 [Program] Window (Setting a Software Breakpoint)
The word [• Break]will be displayed on the line containing the sortfunction to show that
a software breakpoint is set.
33
Download from Www.Somauals Search And Download.
3.8
Setting Registers
Set values of the program counter and the stack pointer before executing the program.
•
Select [Registers] from the [View] menu. The [Registers] window is displayed.
Figure 3.9 [Registers] Window
•
To change the value of the program counter (PC), double-click the value area in the
[Registers] window with the mouse. The following dialog box is then displayed, and the value
can be changed.
Figure 3.10 [Register] Dialog Box (PC)
•
•
Set the program counter to H’1000 in this tutorial program, and click the [OK] button.
To change the value of the stack pointer (SP), move the mouse pointer on the value to be
changed in the [ER7] value area in the [Registers] window and enter the new value by the
34
Download from Www.Somauals Search And Download.
keyboard, or double-click the value area with the mouse. The following dialog box is then
displayed.
Figure 3.11 [Register] Dialog Box (ER7)
•
Set the value of the stack pointer to H’FFFC00 in this tutorial program, and click the [OK]
button.
35
Download from Www.Somauals Search And Download.
3.9
Executing the Program
Execute the program as described in the following:
•
To execute the program, select [Go] from the [Run] menu, or click the [Go] button on the
toolbar.
Figure 3.12 [Go] Button
•
Or, select [Reset Go] from the [Run] menu or click the [Reset Go] button on the toolbar.
Figure 3.13 [Reset Go] Button
The program will be executed up to the breakpoint that has been inserted, and a statement will
be highlighted in the [Program] window to show the position that the program has halted, with
the message [Break=BREAKPOINT] in the status bar.
Figure 3.14 [Program] Window (Break Status)
36
Download from Www.Somauals Search And Download.
The user can see the cause of the break that occurred last time in the [System Status] window.
•
Select [Status] from the [View] menu. After the [System Status] window is displayed, open
the [Platform] page, and check the status of Cause of last break.
Figure 3.15 [System Status] Window
Note: The items that can be displayed in this window differ according to the product. For
the items that can be displayed, refer to the on-line help.
37
Download from Www.Somauals Search And Download.
The [System Status] window displays the following items in each page.
Table 3.3 Contents of the [System Status] Window
Page
Item
Description
[Session]
Target System
Session Name
Program Name
Connected To:
Always displays Connected.
Displays the session file name.
Displays the load module file name.
[Platform]
Displays the name of the connected emulator and the
selected driver name.
CPU
Displays the target MCU name.
Run status
Displays the execution status:
RUNNING: Being executed
Break: Stopped
Cause of last break
Run time count
Displays the cause of the emulator stopping at break. In
this example, the cause of the stop is BREAK POINT.
Displays the program execution time. The display format
is h: hours, min: minutes, s: seconds, and ms:
milliseconds. In this example, 0h0min3s110ms is
displayed.
Emulator mode
Displays the emulator operating mode (setting
information for [Emulation Mode] of the [Configuration]
dialog box).
[Memory]
[Events]
Loaded Memory
Areas
Displays the loaded area of the load module.
Resources
Displays the usage states of BREAKPOINT and Break
Condition.
38
Download from Www.Somauals Search And Download.
3.10
Reviewing Breakpoints
The user can see all the breakpoints set in the program in the [Breakpoints] window.
Select [Breakpoints] from the [View] menu.
•
Figure 3.16 [Breakpoints] Window
The pop-up menu, opened by clicking the [Breakpoints] window with the right mouse button,
also allows the user to set or change breakpoints, define new breakpoints, and delete, enable,
or disable breakpoints.
39
Download from Www.Somauals Search And Download.
3.11
Viewing Memory
The user can view the contents of a memory block in the [Memory] window. For example, to
view the memory contents corresponding to the mainin word size:
•
Select [Memory …] from the [View] menu, enter main in the [Address] edit box, and set
Wordin the [Format] combo box.
Figure 3.17 [Open Memory Window] Dialog Box
•
Click the [OK] button. The [Memory] window showing the specified area of memory is
displayed.
Figure 3.18 [Memory] Window
40
Download from Www.Somauals Search And Download.
3.12
Watching Variables
As the user steps through a program, it is possible to watch that the values of variables used in the
user program are changed. For example, set a watch on the long-type array adeclared at the
beginning of the program, by using the following procedure:
•
•
Click the left of displayed array ain the [Program] window to position the cursor.
Click the [Program] window with the right mouse button and select [Instant Watch...] from a
pop-up menu.
The following dialog box will be displayed.
Figure 3.19 [Instant Watch] Dialog Box
41
Download from Www.Somauals Search And Download.
•
Click [Add Watch] button to add a variable to the [Watch] window.
Figure 3.20 [Watch] Window (Displaying the Array)
The user can also add a variable to the [Watch] window by specifying its name.
•
Click the [Watch] window with the right mouse button and select [Add Watch] from the pop-
up menu.
The following dialog box will be displayed.
Figure 3.21 [Add Watch] Dialog Box
•
Input variable max and click the [OK] button.
42
Download from Www.Somauals Search And Download.
The [Watch] window will now also show the long-type variable max.
Figure 3.22 [Watch] Window (Displaying the Variable)
The user can double-click the + symbol to the left of any variable in the [Watch] window to
watch the all elements in array a.
Figure 3.23 [Watch] Window (Displaying Array Elements)
43
Download from Www.Somauals Search And Download.
3.13
Stepping Through a Program
The HDI provides a range of step menu commands that allow efficient program debugging.
Table 3.4 Step Option
Menu
Command
Description
Step In
Executes each statement, including statements within functions.
Executes a function call in a single step.
Step Over
Step Out
Steps out of a function, and stops at the statement following the statement in the
program that called the function.
Step…
Steps the specified times repeatedly at a specified rate.
44
Download from Www.Somauals Search And Download.
3.13.1 Executing [Step In] Command
The [Step In] steps into the called function and stops at the first statement of the called function.
•
To step through the sortfunction, select [Step In] from the [Run] menu, or click the [Step
In] button in the toolbar.
Figure 3.24 [Step In] Button
Figure 3.25 [Program] Window (Step In)
•
The highlighted line moves to the first statement of the sortfunction in the [Program]
window.
45
Download from Www.Somauals Search And Download.
3.13.2 Executing [Step Out] Command
The [Step Out] steps out of the called function and stops at the next statement of the calling
statement in the main function.
•
To step out of the sortfunction, select [Step Out] from the [Run] menu, or click the [Step
Out] button in the toolbar.
Figure 3.26 [Step Out] Button
Figure 3.27 [Program] Window (Step Out)
•
The data of variable adisplayed in the [Watch] window is sorted in ascending order.
46
Download from Www.Somauals Search And Download.
•
To execute two steps, use [Step In] twice.
Figure 3.28 [Program] Window (Step In −> Step In)
•
The value of maxdisplayed in the [Watch] window is changed to the maximum data value.
47
Download from Www.Somauals Search And Download.
3.13.3 Executing [Step Over] Command
The [Step Over] executes a function call as a single step and stops at the next statement of the
main program.
•
Using [Step Over], execute two steps to reach the changefunction statement.
Figure 3.29 [Program] Window (Before Step Over Execution)
•
To step through all statements in the changefunction at a single step, select [Step Over] from
the [Run] menu, or click the [Step Over] button in the toolbar.
Figure 3.30 [Step Over] Button
48
Download from Www.Somauals Search And Download.
Figure 3.31 [Program] Window (Step Over)
When the last statement of the changefunction is executed, the data of variable a, which is
displayed in the [Watch] window, is sorted in descending order.
49
Download from Www.Somauals Search And Download.
3.14
Displaying Local Variables
The user can display local variables in a function using the [Locals] window. For example, we
will examine the local variables in the mainfunction, which declares five local variables: a, j, i,
min, and max.
•
Select [Locals] from the [View] menu. The [Locals] window is displayed.
Initially, the [Locals] window is empty because local variables have not yet been declared.
Select [Step In] from the [Run] menu to execute a single step.
•
The [Locals] window will now show the local variables and their values.
Figure 3.32 [Locals] Window
•
•
Double-click the + symbol in front of array ain the [Locals] window to display the elements
of array a.
Refer to the elements of array abefore and after the execution of the sortfunction, and
confirm that random data is sorted in descending order.
50
Download from Www.Somauals Search And Download.
3.15
Break Function
The emulator has software and hardware break functions. With the HDI, a software breakpoint
can be set using the [Breakpoints] window, and a hardware break condition can be set using the
[Break condition 1] dialog box.
An overview and setting of the break function are described below.
3.15.1 Software Break Function
The emulator can set up to 255 software breakpoints. Setting a software breakpoint is described
below.
•
•
Select [Breakpoints] from the [View] menu. The [Breakpoints] window is displayed.
Click the [Breakpoints] window with the right mouse button and select [Delete All] from the
pop-up menu to cancel all the breakpoints that have been set.
Figure 3.33 [Breakpoints] Window (Before Software Breakpoint Setting)
•
Click the [Breakpoints] window with the right mouse button and select [Add] from the pop-up
menu.
51
Download from Www.Somauals Search And Download.
The [Break] dialog box is displayed. The [Point] page is displayed as a default.
Figure 3.34 [Point] Page ([Break] Dialog Box)
•
Click the [Add...] button to display the [Breakpoint] dialog box.
52
Download from Www.Somauals Search And Download.
•
Enter H'10a4 to the [Value] edit box.
Figure 3.35 [Breakpoint] Dialog Box
•
Click the [OK] button.
53
Download from Www.Somauals Search And Download.
The [Break] dialog box is displayed. The address set in the value field of [Breakpoint] is
displayed.
Figure 3.36 [Point] Page ([Break] Dialog Box) (After Software Breakpoint Setting)
•
Click the [Close] button.
54
Download from Www.Somauals Search And Download.
The software breakpoint that has been set is displayed in the [Breakpoints] window.
Figure 3.37 [Breakpoints] Window (Software Breakpoint Setting)
To stop the tutorial program at the breakpoint, the following procedure must be executed:
•
•
Close the [Breakpoints] window.
Click the [Reset Go] button.
The program runs, and stops at the set breakpoint.
Figure 3.38 [Program] Window at Execution Stop (Software Break)
55
Download from Www.Somauals Search And Download.
The [System Status] window displays the following contents.
Figure 3.39 Displayed Contents of the [System Status] Window (Software Break)
Note: The items that can be displayed in this window differ according to the product. For
the items that can be displayed, refer to the on-line help.
56
Download from Www.Somauals Search And Download.
3.16
Hardware Break Function
A method is given below in which the address bus condition and the read cycles for the state
condition are set under Break condition 1 as hardware break conditions.
•
•
Select [Breakpoint Window] from the [View] menu. The [Breakpoints] window is displayed.
Click the [Breakpoints] window with the right mouse button and select [Delete All] from the
pop-up menu to cancel all breakpoints that have been set.
•
Click the [Breakpoints] window with the right mouse button and select [Add] from the pop-up
menu.
Figure 3.40 [Breakpoints] Window (Before Hardware Break Condition Setting)
57
Download from Www.Somauals Search And Download.
The [Break] dialog box is displayed. To set hardware break conditions, select [Condition] in the
[Break] dialog box to display the [Condition] page.
Figure 3.41 [Condition] Page ([Break] Dialog Box)
Up to two breakpoints can be set independently for the hardware break condition. In this example,
set the hardware break condition for Break condition 1.
Note: Note that the number of hardware break conditions differs according to the product.
For the number that can be specified for each product, refer to the on-line help.
58
Download from Www.Somauals Search And Download.
•
•
•
•
Highlight the first point in the [Break condition] list box.
Click the [Edit...] button. The [Break condition 1] dialog box is displayed.
Clear the [Don't care] check box in the [Address] page.
Select the [Only program fetched address after] radio button and enter H'108C as the value in
the [Address] edit box.
Figure 3.42 [condition] Page ([Break condition 1] Dialog Box)
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
•
•
Click the [OK] button.
The [Break] dialog box is displayed. Check the first point display in the [Break condition] list
box is changed from Emptyto Enable.
59
Download from Www.Somauals Search And Download.
Figure 3.43 [Break] Dialog Box (After Hardware Break Condition Setting)
Note: Note that the number of hardware break conditions differs according to the product.
For the number that can be specified for each product, refer to the on-line help.
•
Click the [Close] button.
60
Download from Www.Somauals Search And Download.
The newly set hardware breakpoint is displayed in the [Breakpoints] window. With this setting,
Break condition 1is displayed in [Type] in the [Breakpoints] window.
This completes the setting of the Break condition 1 hardware break condition. When the program
is executed, a break will occur when address H'108C is accessed in a read cycle.
Figure 3.44 [Breakpoints] Window ([Break condition 1] Setting)
•
•
Close the [Breakpoints] window.
Click the [Reset Go] button.
61
Download from Www.Somauals Search And Download.
The program runs then stops at the condition specified under Break condition 1.
Figure 3.45 [Program] Window at Execution Stop (Break condition 1)
62
Download from Www.Somauals Search And Download.
The [System Status] window displays the following contents.
Figure 3.46 Displayed Contents of the [System Status] Window (Break condition 1)
Note: The items that can be displayed in this window differ according to the product. For
the items that can be displayed, refer to the on-line help.
63
Download from Www.Somauals Search And Download.
3.17
Trace Function
The trace function of the E10A emulator is described.
The branch source addresses, mnemonics, operands, and source lines are displayed. Since this
function uses the trace buffer built into the MCU, a realtime trace can be acquired.
Run the program as shown in the example of section 3.15.1, Software Break Function. The trace
results are displayed in the [Trace] window after the program execution is completed.
Figure 3.47 [Trace] Window
•
If necessary, adjust the column width by dragging the header bar immediately below the title
bar.
Note: The number of branch instructions that can be acquired by a trace differs according
to the product. For the number that can be specified for each product, refer to the
on-line help.
64
Download from Www.Somauals Search And Download.
3.18
What Next?
This tutorial has described the major features of the emulator and the use of the HDI.
Sophisticated debugging can be carried out by using the emulation functions that the emulator
offers. This provides for effective investigation of hardware and software problems by accurately
isolating and identifying the conditions under which such problems arise.
Further details on the use of the HDI can be found in the separately issued Hitachi Debugging
Interface User's Manual.
65
Download from Www.Somauals Search And Download.
66
Download from Www.Somauals Search And Download.
Section 4 Descriptions of Windows
4.1
HDI Windows
HDI window menu bars and the corresponding pull-down menus are listed in table 4.1. Where a
description of a menu is included in the Hitachi Debugging Interface User's Manual or in this
manual, an O mark or the relevant section number is shown. Related commands in the E10A
Emulator User's Manual are also shown.
Table 4.1 HDI Window Menus and Related Manual Entries
Hitachi
Debugging
Interface
This
Menu Bar
Pull-Down Menu
New Session…
Load Session…
Save Session
Save Session As…
Load Program…
Initialize
User's Manual
Manual
File menu
O
O
O
O
O
O
O
O
O
O
O
O
—
—
2.6
—
3.6.1
—
Exit
—
Edit Menu
Cut
—
Copy
—
Paste
—
Find…
—
Evaluate…
—
67
Download from Www.Somauals Search And Download.
Table 4.1 HDI Window Menus and Related Manual Entries (cont)
Hitachi
Debugging
Interface
This
Menu Bar
Pull-Down Menu
User's Manual
Manual
View Menu Breakpoints
Command Line
Disassembly...
I/O Registers
Labels
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
3.10, 3.15.1, 4.2.3, 6.4.3
—
—
—
—
Locals
3.14
Memory...
3.11
Performance Analysis
—
Profile-List
Profile-Tree
Registers
—
—
3.8
Source…
3.6.2
Status
3.9, 3.15.1, 4.2.9
Trace
4.2.8, 6.4.4
Watch
3.12
—
Localized Dump Window
Run Menu Reset CPU
—
Go
3.9
—
Reset Go
Go to Cursor
Set PC To Cursor
Run…
—
—
—
Step In
3.13.1
3.13.3
3.13.2
—
Step Over
Step Out
Step…
Halt
—
68
Download from Www.Somauals Search And Download.
Table 4.1 HDI Window Menus and Related Manual Entries (cont)
Hitachi
Debugging
Interface
Menu Bar
Pull-Down Menu
User's Manual
This Manual
Memory Menu Refresh
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
—
Load
Save
Verify
Test
—
—
—
—
Fill
—
Copy
Compare
—
—
Setup Menu
Status bar
Options
—
—
Radix
—
Customise
Configure Platform…
—
3.5, 4.2
—
Window Menu Cascade
Tile
—
Arrange Icons
—
Close All
—
Help Menu
Index
—
Using Help
Search for Help on
About HDI
—
—
—
69
Download from Www.Somauals Search And Download.
4.2
Descriptions of Each Window
This section describes each window. Figures in this section are used as examples. Each E10A
emulator type has explanatory notes. Read section 6, H8S/xxxx E10A Emulator Specifications.
4.2.1
[Configuration] Dialog Box
Function:
This dialog box sets the emulation conditions of the emulator.
Window:
Figure 4.1 [Configuration] Dialog Box
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
70
Download from Www.Somauals Search And Download.
Description:
The [Configuration] dialog box consists of the [General] page listed in table 4.2.
Table 4.2 [Configuration] Dialog Box Page
Page Name
Description
[General]
Sets the emulator operation conditions.
Clicking the [OK] button sets the emulation conditions. If the [Cancel] button is clicked, this
dialog box is closed without setting the emulation conditions.
71
Download from Www.Somauals Search And Download.
(1) [General] Page ([Configuration] Dialog Box)
Function:
This page sets the operational conditions for the emulator. The MCU name is displayed, the
emulation mode and interrupts during step execution are set, the JTAG clock (TCK) is displayed
and set, and the driver is selected.
Window:
Figure 4.2 [General] Page ([Configuration] Dialog Box)
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
72
Download from Www.Somauals Search And Download.
Description:
Table 4.3 [General] Page Options
Option
Description
[Mode] combo box
[Emulation mode] combo box
Displays the MCU name.
Selects the emulation mode at user program execution. Select
Normal to perform normal emulation. Select No Break to disable
breakpoint settings.
[Step option] combo box
Enables or disables interrupts during step execution.
Disables interrupts during single step execution: Interrupts during
step execution are masked.
Enables interrupts during single step execution: Interrupts during
step execution are released.
[JTAG clock] combo box
Sets the JTAG frequency*.
[Operating mode] combo box
Displays the operating mode determined by the MD pin.
[Flash memory synchronization] Synchronization method is set between the host computer and
combo box
the flash memory.
When synchronization is performed from the host computer to
the flash memory, a waiting time will be generated to write the
flash memory during user program halting, but the displayed
contents and the flash memory are always matched.
When synchronization is performed from the flash memory to the
host computer, the rewritten contents in the user program mode
will be reflected since the flash memory is read during user
program halting.
Disable: Synchronization is not performed except when the
E10A emulator is activated and the flash memory area is
modified.
PC to Flash memory: Synchronization is performed from the
host computer t the flash memory.
Flash memory to PC: Synchronization is performed from the
flash memory to the host computer.
PC to Flash memory, Flash memory to PC: Synchronization is
performed between the host computer and the flash memory.
[Driver] group box
The [E10A Driver Details] dialog box is displayed. Changes the
driver currently connected.
Note: The range of frequencies that the JTAG operates at is different according to the devices
used. For details, refer to section 6.5.4, Notes on Using the JTAG Clock (TCK).
73
Download from Www.Somauals Search And Download.
When a driver is to be changed with the [Change…] button, the following message is displayed.
Figure 4.3 Warning Message Box
When the [Yes] button is clicked, the [E10A Driver Details] dialog box is displayed. When the
[No] button is clicked, the display returns to the [Configuration] dialog box.
Related Items:
[Configuration] dialog box
GO_OPTION command
STEP_INTERRUPT command
74
Download from Www.Somauals Search And Download.
4.2.2
[E10A Driver Details] Dialog Box
When the [OK] button is clicked, the [E10A Driver Details] dialog box will appear to select the
driver software used by the interface to the emulator. Since the emulator is reinitialized after this
dialog box is closed, it cannot be cancelled.
Figure 4.4 [E10A Driver Details] Dialog Box
Table 4.4 shows each option.
Table 4.4 [E10A Driver Details] Dialog Box Option
Option
Description
[Driver] combo box
[Interface] combo box
[Channel] combo box
[Configure...] button
Selects the driver to connect the HDI with the emulator.
Selects the interface name of the card emulator to be connected.
Selects the interface that the PC interface board has been connected.
Clicked to display that the driver supports the configuration dialog box.
75
Download from Www.Somauals Search And Download.
When the PCMCIA card emulator is used, [E10A PC Card Driver 5] is selected. When the PCI
card emulator is used, [E10A PCI Card Driver 5] is selected.
Note: When the HDI is not linked up even if the above procedure has been executed, the driver
may not be set correctly. Install drivers provided with the \SETUP directory in the CD-R
according to the screen instructions.
Related Items:
[Configuration] dialog box
[General] page
4.2.3
[Breakpoints] Window
Function:
This window lists all break conditions that have been set.
Window:
Figure 4.5 [Breakpoints] Window
76
Download from Www.Somauals Search And Download.
Description:
The [Breakpoints] window displays breakpoint setting information. The items listed in the
following tables are displayed.
Table 4.5 [Breakpoints] Window Display Items
Item
Description
[Enable]
Indicates whether the break condition is enabled or disabled.
Symbol l or m shows that the break condition is enabled.
Displays the file name and line number where the breakpoint is set.
[File/Line]
[Symbol]
Displays the symbol corresponding to the breakpoint address. If no symbol has
been defined for the address, a blank is displayed.
[Address]
[Type]
Displays the address where the breakpoint is set.
Displays the break condition type as follows:
Breakpoint: Software breakpoint
Break condition n: Hardware break condition (n is a number)
The pop-up menu, which is opened by clicking the right mouse button, can be used to set, change,
and clear breakpoints, and to enable or disable break conditions. The pop-up menu functions are
described in the following table.
Table 4.6 [Breakpoints] Window Pop-up Menu Operation
Menu Name
Description
[Add]
Sets break conditions. Clicking this button will display the [Break] dialog
box, enabling break conditions to be set.
[Edit]
Changes break conditions. Select break conditions to be changed and
click this button. The break condition setting dialog box will be displayed,
enabling the break condition to be changed.
[Disable]
([Enable])
Enables or disables break conditions. Select break conditions to be
enabled or disabled and click this button.
[Delete]
Clears break conditions. Select break conditions to be cleared and click
this button.
[Delete All]
Clears all break conditions.
[Go to Source]
Jumps to the address which sets the break in the [Source] window.
77
Download from Www.Somauals Search And Download.
4.2.4
[Break] Dialog Box
Function:
This dialog box displays the break condition settings.
Window:
Figure 4.6 [Break] Dialog Box
78
Download from Www.Somauals Search And Download.
Description:
The [Break] dialog box consists of the pages listed in table 4.7.
Table 4.7 [Break] Dialog Box Pages
Page Name
[Point]
Description
Displays software breakpoint settings.
Displays Break Condition settings.
[Condition]
The dialog boxes which set or modify break conditions can be displayed from the pages above.
Clicking the [Close] button will close this dialog box. The [Apply] button is not supported.
79
Download from Www.Somauals Search And Download.
(1) [Point] Page ([Break] Dialog Box)
Function:
This page displays software breakpoint settings. In this page, software breakpoints can be set,
changed, and cleared.
Window:
Figure 4.7 [Point] Page ([Break] Dialog Box)
80
Download from Www.Somauals Search And Download.
Description:
Table 4.8 [Point] Page Options
Option
Description
[Breakpoint] list box
Lists the software breakpoints currently being set.
The display contents are as follows:
<breakpoint address>
[Add...] button
[Edit...] button
Sets software breakpoints. Clicking this button displays the
[Breakpoint] dialog box.
Changes the software breakpoint selected in the [Breakpoint] list box.
Clicking this button displays the [Breakpoint] dialog box.
[Reset] button
Clears the software breakpoint selected in the [Breakpoint] list box.
Clears all software breakpoints displayed in the [Breakpoint] list box.
[Reset all] button
Related Items:
[Breakpoint] dialog box
BREAKPOINT command
BREAKPOINT_CLEAR command
BREAKPOINT_DISPLAY command
BREAKPOINT_ENABLE command
81
Download from Www.Somauals Search And Download.
(2) [Condition] Page ([Break] Dialog Box)
Function:
This page displays the Break Condition settings. These conditions can also be set or cleared in
this page.
Window:
Figure 4.8 [Condition] Page ([Break] Dialog Box)
Note: Note that the number of hardware break conditions differs according to the product.
For the number that can be specified for each product, refer to the on-line help.
82
Download from Www.Somauals Search And Download.
Description:
Table 4.9 [Condition] Page Options
Option
[Break condition] list box Displays the Break condition settings.
The display at system initiation is as follows: When conditions are set,
Description
Enable is displayed. When no conditions are set, Empty is displayed.
1 Empty (setting of Break condition 1)
2 Empty (setting of Break condition 2)
:
[Edit...] button
[Reset] button
[Reset all] button
Changes the Break condition settings selected in the [Break condition] list
box. Clicking this button displays the [Break condition] dialog boxes.
Clears the Break condition settings selected in the [Break condition] list
box.
Clears all Break condition settings in the [Break condition] list box.
Related Items:
[condition] page
BREAKCONDITION_CLEAR command
BREAKCONDITION_DISPLAY command
BREAKCONDITION_ENABLE command
BREAKCONDITION_SET command
83
Download from Www.Somauals Search And Download.
4.2.5
[Breakpoint] Dialog Box
Function:
This dialog box sets software breakpoints.
Window:
Figure 4.9 [Breakpoint] Dialog Box
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
84
Download from Www.Somauals Search And Download.
Description:
The [Address] page options are as follows:
Table 4.10 [Address] Page Options
Option
Description
[Value] edit box
Sets a breakpoint address with a number or a symbol.
Clicking the [OK] button enables breakpoints to be set. If the [Cancel] button is clicked, this
dialog box is closed without setting breakpoints.
Related Items:
[Point] page
BREAKPOINT command
BREAKPOINT_CLEAR command
BREAKPOINT_DISPLAY command
BREAKPOINT_ENABLE command
85
Download from Www.Somauals Search And Download.
4.2.6
[Break condition] Dialog Box
Function:
This dialog box sets hardware break conditions.
Window:
Figure 4.10 [Break condition 1] Dialog Box
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
86
Download from Www.Somauals Search And Download.
Description:
The [Break condition] dialog box consists of the [condition] page. Sets the conditions for halting
the program.
Contents to be set by this page are described in section 4.2.7, [Break condition] Dialog Box Pages.
Clicking the [OK] button sets the hardware break conditions. If the [Cancel] button is clicked, the
dialog box is closed without setting the hardware break conditions.
Related Items:
[condition] page
BREAKPOINT command
BREAKCONDITION_CLEAR command
BREAKCONDITION_DISPLAY command
BREAKCONDITION_ENABLE command
87
Download from Www.Somauals Search And Download.
4.2.7
[Break condition] Dialog Box Pages
The [Break condition] dialog box page allows a number of hardware break conditions to be set.
Some functions may not be supported by some types of emulators. The setting conditions may
differ from those in table 4.11. For details, refer to section 6.5.2, Hardware Break Functions.
Table 4.11 Setting Conditions in [Break condition] Dialog Box
Type
Address Bus
Dialog Box
Condition
Data Bus Condition
Read/Write Condition
[Break condition 1]
dialog box
O
O
O
O
[Break condition 2]
dialog box
O
O
Note: O: Can be set by checking the radio button in the dialog box.
Table 4.12 shows the [Break condition] dialog box page.
Table 4.12 [Break condition] Dialog Box Pages
Page Name
Function
[condition]
Sets the address bus, data bus, and read/write cycle conditions of Break
condition.
Note: This function differs according to the product. For the specifications of each
product, refer to section 6.5.2, Hardware Break Functions, or to the on-line help.
88
Download from Www.Somauals Search And Download.
(1) [condition] Page
Function:
This page sets the address bus, data bus, and read/write cycle conditions.
Window:
Figure 4.11 [condition] Page
Note: The items that can be set in this window differ according to the product. For the
settings for each product, refer to the on-line help.
89
Download from Www.Somauals Search And Download.
Description:
The [Address] group box sets the address bus conditions.
Table 4.13 [Address] Group Box Options
Option
Description
[Don’t care] check box
[Address] radio button
Does not set address conditions.
Sets use of the normal address bus as break conditions.
Sets a break after prefetched address execution as break conditions.
[Only program fetched
address after] radio button
[Address] edit box
[Mask] list box
Sets the address bus value with a number or a symbol.
Sets the mask bits if [User mask] is selected. For masked bits, the
break condition is satisfied regardless of the address values.
The contents of an option that can be set will change depending on the radio button selected.
Table 4.14 Radio Button Options
Option
Description
[Address] radio button
All conditions can be set.
[Only program fetched address after] radio The [Address] condition can be set.
button
The [Data] group box sets the data bus conditions.
Table 4.15 [Data] Group Box Options
Option
Description
[Don’t care] check box
[Value] edit box
No data conditions are set.
Sets the data bus with a number.
Sets data access size as the lower 8-bit access.
Sets data access size as the upper 8-bit access.
Sets data access size as the word access.
[Low byte] radio button
[High byte] radio button
[Word] radio button
90
Download from Www.Somauals Search And Download.
The [Read/Write] group box sets the read/write cycle conditions.
Table 4.16 [Read/Write] Group Box Options
Option
Description
[Read/Write] radio button
[Read] radio button
[Write] radio button
Sets the read/write cycle conditions as break conditions.
Sets read cycles as break conditions.
Sets write cycles as break conditions.
Related Items:
[Condition] page
BREAKCONDITION_CLEAR command
BREAKCONDITION_DISPLAY command
BREAKCONDITION_ENABLE command
BREAKCONDITION_SET command
91
Download from Www.Somauals Search And Download.
4.2.8
[Trace] Window
Function:
This window displays the trace buffer contents. The contents are displayed in both C and
assembly languages to simplify debugging.
Window:
Figure 4.12 [Trace] Window
Note: This function differs according to the product. For the number that can be specified
for each product, refer to the on-line help.
92
Download from Www.Somauals Search And Download.
Description:
This window displays the trace buffer contents. The items listed in table 4.17 are displayed.
Table 4.17 [Trace] Window Display Items
Item
[IP]
Description
Displays the instruction pointer (signed decimal).
[TYPE]
Displays the branch source.
BRANCH: Branch source
[ADDR]
Displays the branch source address.
[MNEMONIC]
[OPERAND]
[Source]
Displays the execution instruction mnemonic.
Displays the execution instruction operand.
Displays the C-source line of the address that the trace has been acquired.
[Total Records] Displays the total number of instructions displayed as trace information in the
[Trace] window.
The pop-up menu, opened by clicking the right mouse button, can be used to set, change, and
clear trace conditions. For details, refer to the Hitachi Debugging Interface User’s Manual.
Note: The [Halt] menu in the pop-up menu is active only when the [Trace] window is open
during user program execution. Realtime emulation cannot be performed by using the
[Halt] menu.
Related Item:
TRACE_DISPLAY command
93
Download from Www.Somauals Search And Download.
4.2.9
[System Status] Window
Function:
This window lists information, such as conditions that have been set to the emulator and execution
results.
Window:
Figure 4.13 [System Status] Window
Note: The items that can be displayed in this window differ according to the product. For
the items that can be displayed, refer to the on-line help.
94
Download from Www.Somauals Search And Download.
Description:
The items listed in the following table are displayed in the [System Status] window.
Table 4.18 [System Status] Window Display Items
Page
Item
Description
[Session]
Target System
Session Name
Program Name
Connected To
Displays whether the emulator is connected.
Displays the session file name.
Displays the load module file name.
[Platform]
Displays the name of the connected emulator and the
selected driver name.
CPU
Displays the target MCU name.
Run status
Displays the execution status:
Running: Being executed
Break: Stopped
Cause of last break
Run time count
Displays the cause of the emulator stopping at break.
Displays the program execution time. The display format
is h: hours, min: minutes, s: seconds, and ms:
milliseconds. In this example, 0000h00min03s110ms is
displayed.
Emulator mode
Displays the emulator operating mode (setting
information for [Emulation Mode] of the [Configuration]
dialog box).
[Memory]
[Events]
Loaded Memory
Areas
Displays the loaded area of the load module.
Resources
Displays the usage states of software breakpoint and
Break condition.
Related Items:
[Configuration] dialog box
STATUS command
95
Download from Www.Somauals Search And Download.
96
Download from Www.Somauals Search And Download.
Section 5 Command-line Functions
5.1
Table and Symbol Description
This section describes the format used in section 5.2, Command Descriptions. The descriptions of
some commands are given over two or more pages.
5.1.1
Format
The input format for each command is as follows. Characters shown in bold-italics are to be
input.
[ ] : Parameters enclosed by [ ] can be omitted.
< > : Contents shown in < > are set.
< >=: The parameter to the left of the "=" sign is input in the format shown to the right.
|
: This represents a non-exclusive selection.
: This represents an exclusive selection.
| |
The command parameter details are described in the parameter table.
5.1.2 Parameter Input
Numerical Parameters:
A binary, octal, decimal, or hexadecimal value, a symbol, or a formula can be input. A symbol
can contain up to 32 characters. Terms in a formula are separated with operators (such as + or –).
Keyword Parameters:
One of the bold characters given in the description column of the table can be input. If a character
string not shown in the description is input, an error will occur.
Character-String Parameters:
Character-string parameters are used to input mask data or a file name. In the mask data, set a
radix (H’: hexadecimal or B’: binary) at the top of a character string and set * at the digit to be
masked.
97
Download from Www.Somauals Search And Download.
5.1.3
Examples
These are actual input examples. For commands whose execution results in a specific display
output, an example of the display is given.
5.1.4
Related Items
Related E10A HDI commands (abbreviations) and dialog boxes are shown. (Refer to section 4,
Descriptions of Windows.)
98
Download from Www.Somauals Search And Download.
5.2
Command Descriptions
The command list of the E10A emulator is shown below.
Table 5.1 E10A HDI Commands
No Command
Abb. Function
1
2
3
4
BREAKCONDITION_
CLEAR
BCC Clears hardware breakpoints that have been set.
BREAKCONDITION_
DISPLAY
BCD Displays hardware breakpoints that have been set.
BREAKCONDITION_
ENABLE
BCE Enables or disables hardware breakpoints that have
been set.
BREAKCONDITION_
SET
BCS Sets hardware breakpoints.
5
6
7
8
BREAKPOINT
BP
BC
BD
BE
Sets software breakpoints.
BREAKPOINT_CLEAR
BREAKPOINT_DISPLAY
BREAKPOINT_ENABLE
Clears software breakpoints that have been set.
Displays software breakpoints that have been set.
Enables or disables software breakpoints that have
been set.
9
DEVICE_TYPE
DE
GP
Displays MCU type currently selected.
10 GO_OPTION
Sets or displays the emulation mode during user
program execution.
11 JTAG_CLOCK
12 REFRESH
JCK Displays or sets a JTAG clock (TCK) frequency.
RF
Updates the HDI memory information to the latest
contents.
13 RESET
RE
Resets the H8S/xxxx.
14 STATUS
STS Displays emulator status information.
15 STEP_INTERRUPT
SI
Sets or displays the enable or disable status of
interrupts during step execution.
16 TRACE_DISPLAY
TD
Displays acquired trace information.
Note: Support for these commands varies with the product. For the specifications of each
product, refer to the on-line help.
99
Download from Www.Somauals Search And Download.
5.2.1
BREAKCONDITION_CLEAR: BCC
Description:
Clears hardware breakpoints that have been set.
Format:
bcc [<channel>]
<channel> = channel <channel_number>
Table 5.2 BREAKCONDITION_CLEAR Command Parameter
Parameter
Type
Description
None
Examples:
To clear all hardware breakpoints:
>bcc (RET)
To clear all hardware breakpoints set at channel 2:
>bcc channel 2 (RET)
100
Download from Www.Somauals Search And Download.
5.2.2
BREAKCONDITION_DISPLAY: BCD
Description:
Displays hardware breakpoints that have been set. The display contents include enable or disable
of the setting, and setting conditions.
Format:
bcd [<channel>]
<channel> = channel <channel_number>
Table 5.3 BREAKCONDITION_DISPLAY Command Parameter
Parameter
Type
Description
None
Examples:
To display all hardware breakpoint settings:
>bcd (RET)
Break Condition 1:Enable data 20 long
Break Condition 2:Disable address 126
To display the hardware breakpoint set at channel 1:
>bcd channel 1 (RET)
Break Condition 1:Enable data 20 long
Note: The items displayed with this command vary with the product. For the display
specifications of each product, refer to the on-line help.
101
Download from Www.Somauals Search And Download.
5.2.3
BREAKCONDITION_ENABLE: BCE
Description:
Enables or disables hardware breakpoints that have been set.
Format:
bce [<channel>] <mode>
<channel> = channel <channel_number>
Table 5.4 BREAKCONDITION_ENABLE Command Parameter
Parameter
Type
Description
<mode>
Keyword
Enables or disables hardware breakpoint settings.
Set either of the following:
enable: Enables hardware break settings.
disable: Disables hardware break settings.
Examples:
To enable all hardware breakpoints:
>bce enable (RET)
To disable the hardware breakpoints set at channel 1:
>bce channel 1 disable (RET)
102
Download from Www.Somauals Search And Download.
5.2.4
BREAKCONDITION_SET: BCS
Description:
Sets hardware breakpoints.
Note: The function will be different according to the MCUs used. For functions of each
emulator product, refer to section 6.4.2, Hardware Break Functions.
Format:
bcs <channel> <option> [<option> ... ]
<channel>
<option>
<addropt>
=
=
=
channel <channel_number>
[<addropt> | <dataopt> | <asidopt> | <r/wopt>]
address <address> [<addrcycle>] || address mask <maskdata>
<addrcycle>
<dataopt>
<r/wopt>
=
=
data <data> <size>
direction <direction>
103
Download from Www.Somauals Search And Download.
Table 5.5 BREAKCONDITION_SET Command Parameters
Parameter
Type
Description
<address>
Numerical value,
character string
Numerical value or symbol representing an address
bus value
<addrcycle>
Keyword
Address bus access conditions
pcafter: The address bus is targeted during instruction
fetch cycles. Breaks after the instruction at the
address set by the <address> parameter is executed.
When <addrcycle> is omitted, the address in the
program fetch cycles, and the address bus during data
access cycles are targeted.
<maskdata>
Keyword
Address bus mask conditions
Conditions are satisfied regardless of the values of
masked bits. Set a radix H' or B' and set * in the bit to
be masked.
<data>
<size>
Numerical value
Keyword
Data bus value
Sets the access conditions of the data bus. When
<size> is omitted, a byte size is specified.
Specify either of the following:
lbyte: lower 8 bits
hbyte: upper 8 bits
word: word size
<direction>
Keyword
Read/write conditions
Set either of the following keywords:
read: read cycles
write: write cycles
Note: The parameters for this command vary with the product. For the specifications of
each product, refer to the on-line help.
104
Download from Www.Somauals Search And Download.
Examples:
To set the following conditions as a hardware breakpoint:
Address condition: An address bus value of H'1000,
Data condition: A data bus value of H'55 and lower 8-bit byte access,
Read/write cycle condition: Read cycle.
>bcs address 1000 data 55 lbyte direction read (RET)
To set the following conditions as a hardware breakpoint:
Address condition: An address bus value of H'2000 and instruction fetch cycle.
>bcs address 2000 pcafter (RET)
To set the following conditions as a hardware breakpoint:
Address condition: The lower 4 bits of H'1000 are masked,
Data condition: A data bus value of H'aa and upper 8-bit byte access.
>bcs address mask 100* data aa hbyte (RET)
105
Download from Www.Somauals Search And Download.
5.2.5
BREAKPOINT: BP
Description:
Sets software breakpoints.
Note: The function will be different according to the MCUs used.
Format:
bp <address>
Table 5.6 BREAKPOINT Command Parameter
Parameter
Type
Description
<address>
Numerical value,
character string
Breakpoint value set by numerical value or symbol
When an odd address is set, the address is rounded down to
an even address.
Note: The parameters for this command vary with the product. For the specifications of
each product, refer to the on-line help.
Examples:
To set a software breakpoint at address H'12c8:
>bp H'12c8 (RET)
106
Download from Www.Somauals Search And Download.
5.2.6
BREAKPOINT_CLEAR: BC
Description:
Clears software breakpoints that have been set.
Format:
bc [<address>]
Table 5.7 BREAKPOINT_CLEAR Command Parameter
Parameter
Type
Description
<address>
Numerical value,
character string
Breakpoint value set by numerical value or symbol
Note: When no parameters are set, all software breakpoints are cleared.
Note: The parameters for this command vary with the product. For the specifications of
each product, refer to the on-line help.
Examples:
To clear all software breakpoints:
>bc (RET)
To clear all software breakpoints whose address value is H'1000:
>bc H'1000 (RET)
107
Download from Www.Somauals Search And Download.
5.2.7
BREAKPOINT_DISPLAY: BD
Description:
Displays software breakpoints that have been set.
Format:
bd
Table 5.8 BREAKPOINT_DISPLAY Command Parameter
Parameter
Type
Description
None
Example:
To display the software breakpoints that have been set:
>bd (RET)
The display format is as follows:
>bd
H'00000110 Enable
H'0000011c Disable
H'00000250 Enable
Note: The items displayed with this command vary with the product. For the display
specifications of each product, refer to the on-line help.
108
Download from Www.Somauals Search And Download.
5.2.8
BREAKPOINT_ENABLE: BE
Description:
Enables or disables software breakpoints that have been set.
Format:
be <address> <mode>
Table 5.9 BREAKPOINT_ENABLE Command Parameters
Parameter
Type
Description
<address>
Numerical value,
character string
Breakpoint value set by numerical value or symbol
<mode>
Keyword
Enables or disables breakpoints.
Set either of the following:
enable: Enables breakpoints.
disable: Disables breakpoints.
Examples:
To enable software breakpoints that have been set:
>be H'1002 enable (RET)
To disable software breakpoints that have been set:
>be H'1002 disable (RET)
Notes: 1. The parameters for this command vary with the product. For the specifications
of each product, refer to the on-line help.
2. The items displayed with this command vary with the product. For the display
specifications of each product, refer to the on-line help.
109
Download from Www.Somauals Search And Download.
5.2.9
DEVICE_TYPE: DE
Description:
Displays MCU type currently selected.
Format:
de
Table 5.10 DEVICE_TYPE Command Parameter
Parameter
Type
Description
None
Example:
To display the currently selected MCU:
>de (RET)
The display format is as follows:
>de
Current device = H8S/xxxx
110
Download from Www.Somauals Search And Download.
5.2.10 GO_OPTION: GP
Description:
Sets or displays the emulation mode during user program execution.
Format:
gp
Displays emulation mode for user program execution.
gp <eml_opt>
<eml_opt> = eml_mode <eml_mode>
Sets emulation mode for user program execution.
Table 5.11 GO_OPTION Command Parameter
Parameter
Type
Description
<eml_mode>
Keyword
Specifies the emulation mode.
Set either of the following:
normal: Normal execution
no_break: Makes software breakpoints and
hardware breakpoints temporarily invalid and
executes the user program.
Note: The parameters for this command vary with the product. For the specifications of each
product, refer to the on-line help.
Examples:
To display the currently set emulation mode for user program execution:
>gp (RET)
The display format is as follows:
>gp
Emulator execution mode = Normal
To set the normal emulation mode for user program execution:
>gp eml_mode normal (RET)
Note: The items displayed with this command vary with the product. For the display
specifications of each product, refer to the on-line help.
111
Download from Www.Somauals Search And Download.
5.2.11 JTAG_CLOCK: JCK
Description:
Displays or sets the JTAG clock (TCK) frequency.
Format:
JCK
Displays the JTAG clock (TCK).
JCK <jck_opt>
Sets the JTAG clock (TCK).
Table 5.12 JTAG_CLOCK Command Parameter
Parameter
Type
Description
<jck_opt>
Numerical value
Sets one of the JTAG clock (TCK) frequency.
(PCMCIA used: 0.937 MHz, 1.875 MHz, 3.75 MHz,
7.5 MHz, or 15 MHz)
1: 15 MHz
2: 7.5 MHz
3: 3.75 MHz
4: 1.875 MHz
5: 0.937 MHz
(PCI used: 1.031 MHz, 2.062 MHz, 4.125 MHz,
8.25 MHz, or 16.5 MHz)
1: 16.5 MHz
2: 8.25 MHz
3: 4.125 MHz
4: 2.062 MHz
5: 1.031 MHz
Note: The range of the frequency that the Hitachi-UDI operates at differs according to the MCU to
be supported.
112
Download from Www.Somauals Search And Download.
Examples:
(when PCMCIA used):
To set the JTAG clock (TCK) frequency:
>JCK 1 (RET)
JTAG Clock
15MHz
To display the JTAG clock (TCK) frequency:
>JCK (RET)
JTAG Clock
(when PCI used):
15MHz
To set the JTAG clock (TCK) frequency:
>JCK 1 (RET)
JTAG Clock
16.5MHz
To display the JTAG clock (TCK) frequency:
>JCK (RET)
JTAG Clock
16.5MHz
113
Download from Www.Somauals Search And Download.
5.2.12 REFRESH: RF
Description:
Updates the HDI memory information to the latest contents.
Format:
rf
Table 5.13 REFRESH Command Parameter
Parameter
Type
Description
None
Example:
To update the HDI memory information:
>rf (RET)
114
Download from Www.Somauals Search And Download.
5.2.13 RESET: RE
Description:
Resets the H8S/xxxx. The breakpoint settings are retained. After the reset, the registers will be in
the same state as when power is supplied.
Format:
re
Table 5.14 RESET Command Parameter
Parameter
Type
Description
None
Example:
To reset the H8S/xxxx:
>re (RET)
115
Download from Www.Somauals Search And Download.
5.2.14 STATUS: STS
Description:
Displays emulator status information.
Format:
sts
Table 5.15 STATUS Command Parameter
Parameter
Type
Description
None
Example:
To display status information of the emulator:
>sts (RET)
The display format is as follows:
>sts
Emulator Status
Connected to:
CPU
H8S/xxxx E10A Emulator (E10A PC Card Driver 5)
H8S/xxxx
Run status
Break
Cause of last break
Run time count
Emulator mode
Big endian
BREAK KEY
0000h00min03s110ms
Normal
Note: The items displayed with this command vary with the product. For the display
specifications of each product, refer to the on-line help.
116
Download from Www.Somauals Search And Download.
5.2.15 STEP_INTERRUPT: SI
Description:
Sets or displays the enable or disable status of interrupts during step execution. When interrupts
occur when they are disabled, execution stops at the top address of the interrupt routine.
Format:
si
Displays the enable or disable status of interrupts during step execution.
si <mode>
Sets the enable or disable status of interrupts during step execution.
Table 5.16 STEP_INTERRUPT Command Parameter
Parameter
Type
Description
<mode>
Keyword
Enables or disables interrupts during step execution.
Set either of the following:
enable: Enables interrupts.
disable: Disables interrupts.
Example:
To enable interrupts during step execution:
>si enable (RET)
To display interrupt status during step execution:
>si (RET)
Emulator step interrupt mode = ENABLE
117
Download from Www.Somauals Search And Download.
5.2.16 TRACE_DISPLAY: TD
Description:
Displays acquired trace information.
Format:
td
Table 5.17 TRACE_DISPLAY Command Parameter
Parameter
Type
Description
None
Example:
To display acquired trace information:
>td (RET)
The display format is as follows:
>td
IP
TYPE
BRANCH
BRANCH
ADDR
00001010
00001200
MNEMONIC
JSR
JMP
OPERAND
@ER0
@ER1
-D’xxxx
-D’xxxx
(a)
(b)
(c)
(d)
(e)
(a) Instruction pointer (signed decimal)
(b) Type of branch source
BRANCH: Branch source
(c) Address of instruction word
(d) Instruction mnemonic
(e) Instruction operand
118
Download from Www.Somauals Search And Download.
Section 6 H8S/2378F E10A Emulator Specifications
6.1
Overview of the Emulator
The H8S/2378F E10A emulator supports the H8S/2377F and H8S/2367F. The MCU operating
modes 4 and 7 are supported and realtime emulation can be performed. Table 6.1 lists the
components of the emulator.
Table 6.1 Components of the Emulator (HS2378KCM01H or HS2378KCI01H)
Classi-
fication Component
Quan-
tity
Appearance
Remarks
Hard-
ware
Card emulator
1
HS2378KCM01H
(PCMCIA: 14-pin type):
Depth: 85.6 mm,
Width: 54.0 mm,
Height: 5.0 mm,
Mass: 30.0 g
PC
PC
Card
HS2378KCM01H
(Model: HS0005KCM05H),
HS2378KCI01H
or
(Model: HS0005KCI05H)
HS2378KCI01H
(PCI: 14-pin type):
Depth: 122.0 mm,
Width: 96.0 mm,
Mass: 80.0 g
User system interface
cable
1
HS2378KCM01H
(PCMCIA: 14-pin type):
Length: 80.0 cm,
Mass: 46.0 g
HS2378KCI01H
(PCI: 14-pin type):
Length: 150.0 cm,
Mass: 90.0 g
Soft-
ware
H8S/2378F E10A emulator
setup program,
H8S/2378F E10A Emulator
User’s Manual, and
1
HS2378KCM01SR,
HS2378KCM01HJ,
HS2378KCM01HE,
HS6400DIIW5SJ, and
HS6400DIIW5SE
Hitachi Debugging
Interface User’s Manual
(provided on a CD-R)
119
Download from Www.Somauals Search And Download.
6.2
Pin Arrangement of the Hitachi-UDI Port Connector
Figure 6.1 shows the pin arrangement of the Hitachi-UDI port connector.
CAUTION
Note that the pin number assignment of the Hitachi-UDI port
connector differs from that of the connector manufacturer.
Signal
Input/Output *1
Input
H8S/2377F, H8S/2367F
Pin No.
1
PG4
Pin 1 mark
Input
2
P53
Hitachi-UDI port connector
Output
Input
3
#WDTOVF
#RES*2
PG5
4
Input
5
Input
6
PG6
Output
7
#RES*2
GND*3
8 to 10
12 to 14
11
14 pin
7 pin
8 pin
1 pin
Input
Vcc*4
Top view
Note: 1. Input or output from the user system.
2. The symbol (#) means that the signal is active-low.
3. By detecting GND on the user system side, connection or
disconnection with the user system can be determined.
4. Connect Vcc with the Vcc of the MCU.
Pin 1 mark
Figure 6.1 Pin Arrangement of the Hitachi-UDI Port Connector
120
Download from Www.Somauals Search And Download.
Figure 6.2 shows an example of connecting the user system to the emulator.
14-pin connector with
a 2.54-mm pitch
(3M Limited: 2514-6002)
Vcc
Pulls-up at 4.7 k
H8S/2377F, H8S/2367F
11
1
EMLE
PG4
P53
2
3
5
#WDTOVF
PG5
PG6
6
4
User logic
7
#RES
8 to 10
12 to 14
E10A pin No.
User system
· #RES of pin 4 of the Hitachi-UDI port connector is a signal line in which the emulator outputs signals to the MCU.
An AND operation must be performed between #RES (pin 4) and the user system reset circuit for the signal
line connected to the MCU.
· #RES of pin 7 of the Hitachi-UDI port connector is a signal line in which the emulator monitors the #RES signal of
the MCU. The #RES must be pulled up before it is connected to pin 7 of the Hitachi-UDI port connector.
Figure 6.2 Example of Emulator Connection
121
Download from Www.Somauals Search And Download.
Notes: 1. The emulator uses #WDTOVF, P53, and PG4 to PG6 in the H8S/2377F and
H8S/2367F. Pull up the emulator and MCU pins and connect them to the user
system. Peripheral functions that are shared by these pins cannot be used.
H8S/2377F, H8S/2367F
Hitachi-UDI
port connector
Vcc
4.7 k
Pins 1, 2, 3, 5, and 6
Figure 6.3 Connection of Emulator
2. The EMLE pin in the H8S/2377F and H8S/2367F must be pulled up when
connecting with the emulator, and connected to GND when not connecting with
the emulator.
H8S/2377F, H8S/2367F
Vcc
The emulator is connected
to the user system.
4.7 k
EMLE
H8S/2377F, H8S/2367F
The emulator is not connected
to the user system.
EMLE
Figure 6.4 EMLE Pin and Emulator
122
Download from Www.Somauals Search And Download.
3. #RES of pin 4 of the Hitachi-UDI port connector is a signal line in which the
emulator outputs signals to the MCU.
#RES of pin 7 of the Hitachi-UDI port connector is a signal line in which the
emulator monitors the #RES signal of the MCU.
The #RES must be pulled up before it is connected to pin 7 of the Hitachi-UDI
port connector.
Vcc
User
logic
4.7 k
H8S/2377F, H8S/2367F
Hitachi-UDI
port connector
Vcc
Pin 4
Pin 7
4.7 k
Figure 6.5 Connection of #RES Pin
4. Connect GND of pins 8 to 10 and 12 to 14 in the Hitachi-UDI port connector to
GND in the user system.
5. Connect Vcc, pin 11 in the Hitachi-UDI port connector, to the power supply
(Vcc) in the user system. The amount of voltage permitted to input to the
Hitachi-UDI port connector must be within the guaranteed range of the
microcomputer.
6. Figure 6.6 shows the interface circuit in the emulator. Use this figure as a
reference when determining the pull-up resistance value.
Hitachi-UDI
port connector
on the user
sytem
H8S/2377F,
H8S/2367F
Emulator control circuit
Vcc
11
Vcc
4.7 k x 7
22 k x 5
HD74LV125A
Vcc
1
2
4
5
6
PG4
P53
#RES
PG5
PG6
3.3V
HD74LVTH244
Vcc
22 k x 2
3
7
#WDTOVF
#RES
Figure 6.6 Interface Circuit in the Emulator (Reference Figure)
123
Download from Www.Somauals Search And Download.
7. When H8S/2377F and H8S/2367F are connected to the emulator, the following
pin functions cannot be used.
Table 6.2 Unavailable Pin Functions
H8S/2377F
H8S/2367F
P53 and PG4 to PG6
P53 and PG4 to PG6
#WDTOVF
#WDTOVF
#IRQ3
#IRQ3
#ADTRG
#ADTRG
#BREQ, #BACK, and #BREQ0
#BREQ, #BACK, and #BREQ0
#CS4
−
Note: The symbol “#” means that the signal is active-low.
124
Download from Www.Somauals Search And Download.
6.3
Differences between the MCUs and the Emulator
1. When the emulator system is initiated, it initializes the general registers and part of the control
registers as shown in table 6.3.
Table 6.3 Register Initial Values at Emulator Power-On
Register
PC
When Using H8S/2377F and H8S/2367F
Reset vector value in the vector address table
ER0 to ER6
ER7 (SP)
CCR
Undefined
H'FFC000
1 for I mask, and others undefined
H’07
EXR
2. System Control Register
In the emulator, the internal I/O registers can be accessed from the [I/O registers] window.
However, be careful when accessing the system control register. The emulator saves the
register value of the system control register at a break and returns the value when the user
program is executed. Since this is done during a break, do not rewrite the system control
register in the [I/O Registers] window.
3. Memory Access during Emulation
If the memory contents are referenced or modified during emulation, realtime emulation
cannot be performed because the user program is temporarily halted.
4. The emulator communicates with the MCU by using the pins shown in figure 6.1 (section 6.2).
These pins cannot be used.
5. The power consumed by the MCU can reach several mA. This is because the user power
supply drives one HD74LV125A to make the communication signal level match the user-
system power-supply voltage.
125
Download from Www.Somauals Search And Download.
6.4
The H8S/2378F E10A Emulator Functions
Notes: 1. Do not use an MCU that has been used for debugging.
2. If the flash memory is rewritten many times, and the emulator is left for a few days,
data may be lost due to retention problems.
3. If the flash memory is rewritten many times, the data will not be erased. If an error
message is displayed, exchange the MCU for a new one.
6.4.1
Emulator Driver Selection
Table 6.4 shows drivers which can be selected in the [E10A Driver Details] dialog box.
Table 6.4 Type Name and Driver
Type Name
Driver
HS2378KCM01H
HS2378KCI01H
E10A PC Card Driver 5
E10A PCI Card Driver 5
6.4.2
Hardware Break Functions
Hardware Break Conditions: In the H8S/2378F E10A emulator, two break conditions can be
set (Break Condition 1,2). Table 6.5 lists the items that can be specified.
Table 6.5 Hardware Break Condition Specification Items
Items
Description
Address bus condition
Breaks when the MCU address bus value matches the
specified value.
Data bus condition
Breaks when the MCU data bus value matches the specified
value. Bit or word can be specified as the access data size.
Read or write condition
Breaks in the read or write cycle.
Table 6.6 lists the combinations of conditions that can be set in the [Break condition] dialog box.
126
Download from Www.Somauals Search And Download.
Table 6.6 Conditions Set in [Break condition] Dialog Box
Condition
Address Bus
Condition
Data
Condition
Read or write
condition
Dialog Box
[Break condition 1]
[Break condition 2]
O
O
O
O
O
O
Note: O: Can be set by checking the radio button in the dialog box.
Table 6.7 lists the combinations of conditions that can be set by the BREAKCONDITION_SET
command.
Table 6.7 Conditions Set by BREAKCONDITION_SET Command
Condition
Address Bus
Condition
Data
Condition
Read or write
condition
Channel
(<addropt> option)
(<dataopt> option)
(<r/wopt> option)
Break condition 1
Break condition 2
O
O
O
O
O
O
Note: O: Can be set by the BREAKCONDITION_SET command.
Notes on Setting the Break Condition:
1. When [Go to cursor], [Step In], [Step Over], or [Step Out] is selected, the settings of Break
Condition are disabled.
2. The settings of Break Condition is disabled when an instruction to which a software
breakpoint has been set is executed.
3. When step over function is used, the settings of software breakpoint and Break Condition are
disabled.
127
Download from Www.Somauals Search And Download.
6.4.3
Notes on Setting the [Breakpoint] Dialog Box
1. When an odd address is set, the address is rounded down to an even address.
2. A software break is accomplished by replacing instructions. Accordingly, it can be set only to
the flash memory or the RAM area. However, a software break cannot be set to the following
addresses:
• An area other than flash memory or RAM
• An instruction in which Break Condition is satisfied
3. During step execution, a software breakpoint is disabled.
4. A condition set at Break Condition is disabled immediately after starting execution when an
instruction at a software breakpoint is executed. A break does not occur even if a condition of
Break Condition is satisfied immediately after starting the execution.
5. When execution resumes from the breakpoint address after the program execution stops at the
software breakpoint, single-step execution is performed at the address before execution
resumes. Therefore, realtime operation cannot be performed.
6. Settings of software breakpoint and Break Condition are invalid while the STEP OVER
function is being used.
128
Download from Www.Somauals Search And Download.
6.4.4
Trace Function
The emulator uses the branch-instruction trace and bus trace functions in the MCU, and
acquires a trace by operating the user program in realtime. The branch-instruction trace
function displays the branch-source address, the mnemonic, and the operand. The bus trace
function displays and searches the information on the address bus, data bus, memory access,
interrupt, and bus cycle, the mnemonic, and the operand. The acquisition conditions can also
be set.
(1) Setting the Trace Acquisition
The acquisition condition on the trace information is set.
Table 6.8 Setting Trace Acquisition
Acquisition Condition
Description
Trace type
Sets the trace information for acquisition and display.
Branch trace: Acquires and displays the branch-instruction trace
information.
Bus trace: Acquires and displays the bus trace information.
Bus trace mode
Sets the trace acquisition condition when Bus trace is selected as
Trace type. This is not set when Branch trace is selected.
•
[Full Trace] check box
Indicates that all cycles are acquired.
[Suppress] group box
•
Sets a cycle to suppress acquisition.
DMAC Cycles: Suppresses acquiring the DMAC cycle.
DTC Cycles: Suppresses acquiring the DTC cycle.
CPU Instruction fetch Cycles: Suppresses acquiring the CPU-
instruction fetch cycle.
CPU Data access Cycles: Suppresses acquiring the CPU-data
access cycle.
•
[Address] group box
Sets the address condition to be acquired. Only A23 to A12 of the
address value can be set. Mask the lower 12 bits (A11 to A0).
129
Download from Www.Somauals Search And Download.
(2) Displaying a Trace in the Bus Trace Function
The contents of the trace buffer in table 6.9 are displayed in the [Trace] window.
Table 6.9 Items in the [Trace] Window
Item
Description
[IP/Cycle]
[Address]
[Label]
Instruction pointer or bus cycle pointer (signed decimal)
The value of the address bus
Label name
[Mnemonic]
[Operand]
[Data]
Mnemonic of the execution instruction
Operand of the execution instruction
The value of the data bus
[R/W]
Type of the read/write signal
RD: read cycle
WT: write cycle
[Area]
Type of the access area
ROM: ROM area
RAM: RAM area
IO-8: 8-bit I/O
IO-16: 16-bit I/O
EXT-8: 8-bit external area
EXT16: 16-bit external area
DTC: DTC area
[Status]
Type of the access cycle
PROG: CPU-instruction fetch cycle
DATA: CPU-data access cycle
DMAC: DMAC bus cycle
DTC: DTC bus cycle
REFRESH: Refresh cycle
[Clock]
[IRQ]
The number of clocks of the bus cycle
Ored states of pins IRQ15 to IRQ0
0: Low
1: High
[Source]
The C-source line of the address in which the trace is acquired
130
Download from Www.Somauals Search And Download.
(3) Searching a Trace in the Bus Trace Function
The emulator supports two types of trace search function listed in table 6.10.
Table 6.10 Trace Search Function
Function
Description
Trace Filter
Displays all the information that matches the conditions specified by all the trace
data.
Trace Find
Jumps to the information that matches the conditions specified by all the trace
data.
(i) Trace Filter Function
The emulator displays all the information that matches the specified conditions for all the trace
data. The search function is set in the [Trace Filter] dialog box.
Table 6.11 [Address] Group Box Options
Option
Description
[Don’t care] check box
[Address] radio button
[Range] radio button
[Start] edit box
Indicates that no address condition is set.
Sets an address as a display condition.
Sets an address range as a display condition.
Sets the start value of the address range as a numeric or a
symbol.
[End] edit box
Sets the end value of the address range as a numeric or a
symbol.
[Outside range] check box
Sets outside the specified address range as a display condition.
Table 6.12 [Data] Group Box Options
Option
Description
[Don’t care] check box
[Data] edit box
Indicates that no data condition is set.
Sets the data value as a numeric or a symbol.
Sets the byte access as a display condition.
Sets the word access as a display condition.
[Byte] radio button
[Word] radio button
131
Download from Www.Somauals Search And Download.
Table 6.13 [Bus status] Group Box Options
Option
Description
[Don’t care] check box
[DMAC] check box
[DTC] check box
[PROG] check box
[DATA] check box
[REFRESH] check box
Indicates that no bus condition is set.
Sets a DMAC bus cycle as a display condition.
Sets a DTC bus cycle as a display condition.
Sets a CPU instruction fetch cycle as a display condition.
Sets a CPU data access cycle as a display condition.
Sets a refresh cycle as a display condition.
Table 6.14 [Area] Group Box Options
Option
Description
[Don’t care] check box
[ROM] check box
[RAM] check box
[IO-8] check box
[IO-16] check box
[EXT-8] check box
[EXT-16] check box
[DTC] check box
Indicates that no area condition is set.
Sets a ROM area as a display condition.
Sets a RAM area as a display condition.
Sets an 8-bit I/O area as a display condition.
Sets a 16-bit I/O area as a display condition.
Sets an 8-bit external area as a display condition.
Sets a 16-bit external area as a display condition.
Sets a DTC area as a display condition.
Table 6.15 [Read/Write] Group Box Options
Option
Description
[Don’t care] check box
[Read] radio button
[Write] radio button
Indicates that no read/write condition is set.
Sets a read cycle as a display condition.
Sets a write cycle as a display condition.
Table 6.16 [IRQ] Group Box Options
Option
Description
[Don’t care] check box
[High] radio button
[Low] radio button
Indicates that no IRQ condition is set.
Sets the high level of IRQ as a display condition.
Sets the low level of IRQ as a display condition.
132
Download from Www.Somauals Search And Download.
(ii) Trace Find Function
The emulator jumps to the information that matches the conditions specified by all the trace
data on the [Trace] window. The search function is set in the [Trace Filter] dialog box. The
conditions to be set are the same as those of the Trace Filter function.
(4) Commands for the Trace Function
The emulator supports the commands for the trace function listed in table 6.17. The contents
of the trace buffer are displayed in the [Trace] window.
Table 6.17 Commands for the Trace Function
Command Name
TRACE_DISPLAY
TRACE_MODE
Description
Displays the acquired trace information.
Displays or sets the acquisition mode of the trace information.
Searches and displays the trace information with the specified condition.
TRACE_SEARCH
(i) TRACE_DISPLAY: TD
Description:
Displays the acquired trace information.
Format:
td [<option1> [<option2>]]
<option1> = start <start>
<option2> = end <end>
Table 6.18 TRACE_DISPLAY Command Parameter
Parameter
<start>
Type
Description
Numerical value (-n)
A start pointer for the trace display.
<end>
Numerical value (-m) An end pointer for the trace display.
133
Download from Www.Somauals Search And Download.
Example:
To display the acquired trace information:
td (RET)
The display format of the branch trace information is as follows:
>td
IP
TYPE
BRANCH
BRANCH
ADDR
00100100
00100200
MNEMONIC
JSR
JMP
OPERAND
@ER0
@ER1
-D’xxxx
-D’xxxx
(a)
(b)
(c)
(d)
(e)
(a) Instruction pointer (signed decimal)
(b) Type of branch source
BRANCH: Branch source
(c) Address of instruction word
(d) Instruction mnemonic
(e) Instruction operand
The display format of the bus trace information is as follows:
>td start -10 end –5
CYCLE
ADDRESS
00FF600C
00FF600E
00FF6100
00FF6010
00FF6104
00FF6012
(b)
LABEL
MNEMONIC
MOV.B
OPERAND
@ER1,R4L
@ER2,E4
DATA
681C
692C
11
R/W
RD
RD
RD
RD
RD
RD
(g)
AREA
RAM
RAM
RAM
RAM
RAM
RAM
(h)
STATUS
PROG
PROG
DATA
PROG
DATA
PROG
(i)
CLOCK
IRQ
0
-D'0010
-D'0009
-D'0008
-D'0007
-D'0006
-D'0005
(a)
1
MOV.W
1
0
1
0
MOV.L
@ER3,ER5
0100
5566
6935
(f)
1
0
1
0
1
0
(c)
(d)
(e)
(j)
(k)
(a) Cycle (signed decimal)
(b) Address
(c) Label
(d) Instruction mnemonic
(e) Instruction operand
(f) Data
(g) Read/write
(h) Access area
(i) Bus cycle status
(j) Bus cycle count
(k) IRQ pin
134
Download from Www.Somauals Search And Download.
(ii) TRACE_MODE: TM
Description:
Displays or sets the acquisition mode of the trace information.
Format:
tm
Displays the acquisition mode of the trace information.
tm <option1> [<option2>] [<option3>] [<option4>]
Sets the acquisition mode of the trace information.
<option1> = type <type>
<option2> = bus mode <mode>
<option3> = cycle <cycle>
<option4> = address <address>
Table 6.19 TRACE_MODE Command Parameter
Parameter
Type
Description
<type>
Keyword
Sets a type of traces to be acquired.
branch: Acquires the branch trace.
bus: Acquires the bus trace.
<mode>
<cycle>
Keyword
Keyword
full: Acquires the bus trace without conditions.
Sets a cycle to disable acquiring the trace.
dmac: Disables acquiring the DMAC bus cycle.
dtc: Disables acquiring the DTC bus cycle.
prog: Disables acquiring the CPU-instruction
fetch cycle.
data: Disables acquiring the CPU data access
cycle.
<address>
Numerical value,
character string
Sets the address condition.
135
Download from Www.Somauals Search And Download.
Example:
To disable acquiring the DMAC cycle in the bus trace:
tm type bus cycle dmac (RET)
The display format of the setting state of the trace acquisition mode is as follows:
>tm (RET)
type = bus cycle dmac
136
Download from Www.Somauals Search And Download.
(iii) TRACE_SEARCH: TS
Description:
Searches and displays the trace information with the specified condition.
Format:
ts [<addropt>] [<dataopt>] [<statusopt>] [<areaopt>] [<rwopt>] [<irqopt>]
[<fromopt>]
<addropt> = address <address>
<dataopt> = data <data> <size>
<statusopt> = status <status>
<areaopt> = area <area>
<rwopt> = rw <rw>
<irqopt> = irq <irq>
<fromopt> = from <from>
137
Download from Www.Somauals Search And Download.
Table 6.20 TRACE_SEARCH Command Parameter
Parameter
Type
Description
<address>
Numerical value,
character string
Sets the address value as a numeric or a
symbol.
<data>
<size>
Numerical value
Keyword
Sets a value of the data bus.
Sets the access condition of the data bus.
byte: Byte access
word: Word access
<status>
Keyword
Sets the bus condition.
dmac: The DMAC bus cycle is the search
condition.
dtc: The DTC bus cycle is the search condition.
prog: The CPU-instruction fetch cycle is the
search condition.
data: The CPU-data access cycle is the search
condition.
refresh: The refresh cycle is the search
condition.
<area>
Keyword
Sets the area condition.
rom: The ROM area is the search condition.
ram: The RAM area is the search condition.
io-8: The IO-8 area is the search condition.
io-16: The IO-16 area is the search condition.
ext-8: The EXT-8 area is the search condition.
ext-16: The EXT-16 area is the search condition.
dtc: The DTC area is the search condition.
<rw>
<irq>
Keyword
Keyword
Sets the read/write condition.
read: The read cycle is the search condition.
write: The write cycle is the search condition.
Sets the IRQ condition.
high: The high level of IRQ is the search
condition.
low: The low level of IRQ is the search condition.
<from>
Numerical value (-n)
Specifies the number of cycles for starting
search.
138
Download from Www.Somauals Search And Download.
Example:
To search and display the trace data of address H’00FF8000:
ts address H’ff8000 (RET)
When the data exists in the –70 cycle, the display format is as follows:
>ts address H’ff8000
CYCLE
ADDRESS
LABEL
xxx
xxx
xxx
xxx
xxx
xxx
xxx
xxx
xxx
xxx
MNEMONIC
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
OPERAND
xxx
DATA
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
R/W
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
AREA
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
STATUS
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
CLOCK
IRQ
x
*-D'0075
*-D'0074
*-D'0073
*-D'0072
*-D'0071
>-D'0070
*-D'0069
*-D'0068
*-D'0067
*-D'0066
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
00ff8000
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
x
x
x
x
x
x
x
x
x
x
xxx
x
xxx
x
xxx
x
xxx
x
xxx
x
xxx
x
xxx
x
xxx
x
xxx
x
139
Download from Www.Somauals Search And Download.
6.4.5
Notes on HDI
1. Note on Moving Source File Position after Creating Load Module
When the source file is moved after creating the load module, the [Open] dialog box may be
displayed to specify the source file during the debugging of the created load module. Select
the corresponding source file and click the [Open] button.
2. Source-Level Execution
Source file
Do not display source files that do not correspond to the load module in the program
window. For a file having the same name as the source file that corresponds to the load
module, only its addresses are displayed in the program window. The file cannot be
operated in the program window.
Step
Even standard C libraries are executed. To return to a higher-level function, enter Step
Out. In a for statement or a while statement, executing a single step does not move
execution to the next line. To move to the next line, execute two steps.
3. Operation During Accessing Files
Do not perform other operations during saving in the [Load Program], [Verify Memory],
[Save Memory], or [Trace] window because this will not allow correct saving to be performed.
4. Source Window at Program Change
When a program being displayed in the source window is changed and the source file and load
module are reloaded, close and reopen the source window once. If the window is not closed
and reopened, the display will be illegal.
5. Watch
Local variables at optimization
Depending on the generated object code, local variables in a C source file that is compiled
with the optimization option enabled will not be displayed correctly. Check the generated
object code by displaying the [Disassembly] window.
If the allocation area of the specified local variable does not exist, displays as follows.
Example:
The variable name is asc.
asc = ? - target error 2010 (xxxx)
Variable name specification
When a name other than a variable name, such as a symbol name or function name, is
specified, no data is displayed.
140
Download from Www.Somauals Search And Download.
Example:
The function name is main.
main =
Array display
When array elements exceed 1000, elements from after 1000 will not be displayed.
6. Memory Load Function
When [Load...] is selected from the [Memory] menu, the Memory Load function can be used
although it takes time to download. It is recommended that the File Load function ([Load
Program...] selected from the [File] menu) is used to load the S-type file.
Note: The File Load function deletes the debugging information of the previously loaded
program. When other load modules are loaded after the program to be debugged has been
loaded, use the following sequence: Link the program to be debugged with the Sdebug
option and save the debugging information in another file. Load the debugging
information file after all the load modules have been loaded.
7. Line Assembly
Input radix
Regardless of the Radix setting, the default for line assembly input is decimal. Specify H’
or 0x as the radix for a hexadecimal input.
8. Command Line Interface
Batch file
To display the message “Not currently available” while executing a batch file, enter the
sleep command. Adjust the sleep time length which differs according to the operating
environment.
Example:
To display “Not currently available” during memory_fill
execution:
sleep d’3000
memory_fill 0 ffff 0
Overwrite file
In Command Line Interface, a file having the same name as the output file is overwritten
without asking the user.
File specification by commands
The current directory may be altered by file specifications in commands. Absolute paths
should be used to specify the files in a command file so that the current directory alteration
is not affected.
141
Download from Www.Somauals Search And Download.
Example:
FILE_LOAD C:\\HEW\\HDI5\\E10A\\2378F\\TUTORIAL
\\TUTORIAL.ABS
9. Note on Initiating HDI
When the emulator is initiated by using another card emulator after it has been initiated by
using the PCI card emulator, delete the [TARGET] line from the C:\windows\HDI.INI file.
10. Usage with Another HDI
Automatic load of session files
Since the emulator cannot use another HDI, re-install this HDI whenever another HDI has
been previously installed is used.
If another HDI has been used, initiate this HDI with “Run” as follows without using the
session files.
<Directory path name in which HDI is installed>\hdi /n (RET)
/n initiates the HDI without loading the recently used session files.
If there is another session file in the different debug platform, the following error message
is displayed:
invalid target system: <recently used debug platform name>
11. [Select Function] dialog box
This HDI does not support software breakpoint setting in the [Select Function] dialog box
(described in section 10, Selecting Functions, in the Hitachi Debugging Interface User's
Manual).
12. Memory Save During User Program Execution
Do not execute memory save verifying during user program execution.
13. Loading Motorola S-type files
This HDI does not support Motorola S-type files with only the CR code (H'0D) at the end of
each record. Load Motorola S-type files with the CR and LF codes (H'0D0A) at the end of
each record.
14. [Memory] window
If the following memory contents are displayed, they will be incorrect.
Word access from address 2n + 1
Longword access from address 4n + 1, 4n + 2, or 4n + 3
15. Scrolling Window During User Program Execution
Do not scroll the [Memory] and [Disassembly] windows by dragging the scroll box during
user program execution. This generates many memory reads causing the user program to stop
execution until the memory reads have been completed.
142
Download from Www.Somauals Search And Download.
16. [I/O Registers] window
Display and modification
Do not change values in the [I/O Registers] window because the emulator uses the address
break controller.
Note that the E10A emulator does not support the display of the invalid module or bit
information in the [I/O Registers] window (described in section 8, Displaying Variables, in
the Hitachi Debugging Interface User's Manual).
Verify
In the [I/O Registers] window, the verify function of the input value is invalid.
17. Note on [Registers] Window Operation During Program Execution
Although a dialog box is displayed in which the register contents can be changed by double-
clicking the [Registers] window, do not change the register contents during program
execution.
18. Note on Radix in the [Register] Dialog Box
The default input radix in the [Register] dialog box is hexadecimal irrespective of the Radix
display. When a radix other than a hexadecimal is input, specify the prefix code such as B'.
After the value has been input in the [Register] dialog box, the Radix setting is changed to
hexadecimal. When the radix other than a hexadecimal is used as a default, reset the Radix
display.
19. Software Break
Session file
If the address set as the breakpoint is wrong, the error message is not output. The
breakpoint is registered as DISABLE in the [Breakpoints] window.
[Breakpoints] window
During user program execution, it is impossible to jump from the breakpoint to the source
or address line in the [Source] or [Disassembly] window by using [Go to Source] in the
popup menu displayed in the [Breakpoints] window.
When the software breakpoint is set in the flash memory area, the program is written to the
flash memory each time the user program is executed. At this time, note that the number
of rewritable times will be decreased.
Breakpoint cancellation
When the contents of the software breakpoint address is modified during user program
execution, the following message is displayed when the user program stops.
BREAKPOINT IS DELETED A=xxxxxxxx
If the above message is displayed, cancel all software breakpoint settings with the [Delete
All] or [Disable] button in the [Breakpoints] window.
143
Download from Www.Somauals Search And Download.
20. Number of Software Breakpoint and [Stop At] Settings in the [Run...] Menu
The maximum number of software breakpoints and [Stop At] settings allowed in the [Run...]
menu is 255. Therefore, when 255 software breakpoints are set, specification by [Stop At] in
the [Run...] menu becomes invalid. Use the software breakpoints and [Stop At] in the [Run...]
menu with 255 or less total settings.
21. Note on RUN-TIME Display
The execution time of the user program displayed in the [Status] window is not a correct value
since the timer in the host computer has been used.
22. Note on Displaying COMMUNICATION TIMEOUT ERROR
If COMMUNICATION TIMEOUT ERROR is displayed, the emulator cannot communicate
with the MCU. Select [Initialize] from the [File] menu to initialize the emulator.
23. Note on Downloading Program
In the [Load Program] dialog box, which is opened when [Load Program…] is selected, the
verify function is invalid. After downloading the program, perform verify in the [Verify S-
Record File with Memory] dialog box, which is opened when [Verify] is selected from the
[Memory] menu.
24. Support of Double Float Format
In the following memory operations, the double float format is not supported:
[Fill Memory] dialog box
[Search Memory] dialog box
MEMORY_FILL command
The [Format] specification in the [Copy Memory] dialog box is ignored. Memory is
copied in a byte unit.
25. Note on Continuous Step Execution
When the step is continuously executed by selecting [Step...] from the [Run] menu, do not use
the software breakpoint because this will cause the HDI to abnormally operate.
26. Note on Using the [Run program] Dialog Box
When [Run...] is selected from the [Run] menu to specify the stop address, there is the
following note:
When the breakpoint that has been set as Disable is specified as the stop address, note that
the breakpoint becomes Enable when the user program stops.
27. Note on Transition to Low-Power Consumption Mode
The hardware standby function must not be used. If it is not used, the emulator will not operate
normally.
144
Download from Www.Somauals Search And Download.
28. Note on Starting or Halting User Program
When the user program execution is started or halted, the program for the H8S/2378F E10A
emulator will write or read the flash memory. The write or read processing will take about a
maximum of 40 seconds.
29. Processing Time for Updating the Flash Memory Contents
When the contents of the flash memory area is modified by the program loading, memory
window, or memory command, or when a software break is set, a waiting time will be
generated to write or read the flash memory before executing the user program.
The processing time for updating the flash memory contents will be about a maximum of 40
seconds under the following environments (reference values):
Host computer: 500 MHz (Pentium® III)
H8S/2377F: 25 MHz (system clock frequency)
30. Functions not Supported by the HDI
The following menu options and popup menu options are not supported:
[Memory -> Test], [Memory -> Compare], [View -> Performance Analysis], [Memory ->
Configure Map], [Memory -> Configure Overlay], and [Trace] popup menu options (Halt,
Restart, and Snapshot)
31. Memory Access during Emulation
When a memory is accessed from the memory window, etc. during user program execution,
the user program is resumed after it has stopped in the E10A emulator to access the memory.
Therefore, realtime emulation cannot be performed.
The stopping time of the user program is as follows:
Environment:
Host computer: 500 MHz (Pentium® III)
H8S/2377F: 25 MHz (system clock frequency)
When a one-byte memory is read from the command-line window, the stopping time will be
about 47 ms.
32. Internal Flash Memory
The actual MCUs H8S/2377F and H8S/2367F, which have been used by connecting to the
emulator, have been written by the flash memory at emulation and stressed. Do not use the
H8S/2377F and H8S/2367F that have been used for debugging for the mass products.
The emulator is used for debugging and does not support writing the flash memory for mass
products of the user system. Do not use the emulator in the mass production process.
145
Download from Www.Somauals Search And Download.
33. Watchdog Timer
When the emulator is connected to operate the watchdog timer (WDT) during using the
H8S/2377F and H8S/2367F, the WDT continues operation during a break.
•
When a counter value overflows during a break in the watchdog timer mode:
An internal reset signal is generated when the internal LSI is reset.
When a counter value overflows during a break in the interval timer mode:
An interrupt request is generated, but it is suspended during a break.
•
146
Download from Www.Somauals Search And Download.
|