®
TitaniumPR
O
Shaving System
Use and
Care Guide
MS-700
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd
1
11/1/06 10:40:37 AM
■ Always store this appliance and
cord in a moisture-free area.
Do not store it in temperatures
exceeding 140°F (60°C).
■ Do not use this appliance with
a damaged or broken head or
cutters, as facial injury may occur.
■ Shavers, including the trimmer,
are for use on facial hair only.
Should not be used for shaving
the hair on your head or any
other part of your body.
IMPORTANT SAFETY
INSTRUCTIONS
■
Do not plug or unplug this appliance
when your hands are wet.
■ Do not wrap the cord around the
appliance.
When using an electrical appliance,
■ The power unit is intended to be
correctly oriented in a vertical or
floor mount position.
■ Do not use an extension cord
or a voltage converter with this
appliance.
■ Always attach the plug to the
appliance, then to the outlet. To
disconnect, turn all controls to
OFF, then remove plug from outlet.
Detach removable power cords
from appliances for storage.
basic precautions should always be
observed, including the following.
WARNING
To reduce the risk of burns, fire,
electric shock or injury to persons:
■ This appliance is for household
use only.
■ An appliance should never be left
unattended when it’s plugged
in, except when charging a
READ ALL
INSTRUCTIONS
BEFORE USING.
rechargeable appliance.
DANGER
■ Close supervision is necessary
when this appliance is used by,
on, or near children or invalids.
■ Use this appliance only for its
intended use as is described in
this manual. Do not use
To reduce the risk of electric shock:
■ Do not reach for an appliance that
has fallen into water. Unplug it
immediately.
■ Do not place or store this appliance
where it can fall or be pulled into a
tub or sink while it is plugged in.
attachments not recommended by
manufacturer.
■ Keep the cord away from heated
surfaces.
■ Except when charging, always
unplug this appliance from the
■ Never operate this appliance if it
has a damaged cord or plug, if it is
not working properly, if it has been
dropped or damaged, or if it has
been dropped into water.
■ Never drop or insert any object into
any of the appliance’s openings.
■ Do not use outdoors or operate
where aerosol (spray) products
are being used, or where oxygen is
being administered.
■ Electrical outlet immediately
after using.
■ Unplug this appliance before
cleaning it.
■ Use only when the shaver is in
dry condition.
■ Detach the appliance from the power
supply cord before cleaning.
SAVE THESE INSTRUCTIONS
Contents
■ Do not submerge shaver in water.
English ......................1
Spanish ...................17
French .....................33
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd 2-3
11/1/06 10:40:38 AM
Product Features
(A)
Shaver Parts
TitaniumPRO Shaving System
Congratulations on your purchase of a premium
(A) Screen & cutter assembly
(B) 3-position trimmer
(C) Trimmer push tab
(D) On/off button
®
Remington TitaniumPRO Shaving System with Revolutionary
(B)
Titanium Shaving Technology.
(E)
(E) Head release button
(E)
(C)
(one on each side)
Run
Time
Power system
Washable
(F) Charging/Low Battery LED
(G) Headguard
(H) Cleaning brush
(I) Storage pouch
(J) Charger
MS700
Cordless only
X
60 min
(D)
(F)
Power System
■ Cordless shavers can only be used
without the cord.
Indicator Lights
Charging
The charging indicator is a green light that
glows when the shaver is charging or fully
charged.
Low-charge
The low-charge indicator is a red light that
glows when the shaver needs recharging.
You have approximately 5 minutes of
shaving time left when the red indicator
first comes on.
(G)
(J)
(I)
(H)
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd 4-5
11/1/06 10:40:40 AM
How To Use
Usage Tips
Adjusting to your new shaver
To shave
Removing the Headguard
To Charge Your Shaver
As with every shaver, your shave will
improve over time. Allow about three
weeks to develop an effective shav-
ing style and for your beard to adjust
to the new shaver. The adaptation
period may take a little longer if your
skin is sensitive, or if you alternate
between shaving methods.
Push the ON/OFF
Before operating your shaver, remove
the headguard, which protects the
screen and cutter assembly. Simply
push up from the front or the back
until it pops off.
Prior to using your shaver for the first
time, put it on charge for 24 hours.
button. Hold the
shaver so all screens
touch your face at
the same time. This
■ Use only the charging adapter
supplied with the shaver.
■ Make sure your shaver is
turned off.
allows the shaver to
work the way it was designed for the
closest shave and minimum wear.
Avoid holding the shaver at an angle
so only one screen touches the skin
at a time. This will distort the screen
and could cause skin irritation.
CAUTION: Always keep the protective
headguard on the shaver head and
keep the trimmer in the OFF position
when the shaver is not in use.
■ Connect the cord to the shaver,
then plug the charging adapter into
the electrical outlet. A charging
indicator light will come on.
■ Your shaver cannot be
overcharged, so you can leave it
plugged in and charging between
shaves.
■ To preserve the life of the batteries,
let them fully run out every six
months, then recharge them for a
full 24 hours.
■ The MS-700 is designed for
cordless operation only. Plugging in
the cord will not power the shaver.
To help smooth the transition to your
new shaver, Remington has applied
a special lubricant to the shaver’s
screens and cutters. The lubricant
looks like fine, white or gray powder,
and disappears with use.
Operating the Trimmer
Your shaver is equipped with a 3-
position trimmer.
Use the trimmer
button to extend or
retract the trimmer.
1. Completely
retracted (down),
the trimmer is out of the way and
off, for when you want to use the
screens alone. Slide the trimmer
button down with your thumb to
get it into this position.
2. In the middle position, the trimmer
works with the screens, cutting
the longer, hard-to-shave hairs so
the screens can get in extra close.
Slide the trimmer button into the
position level with the foils.
Shave with short,
circular strokes. Use
your free hand to
stretch your skin.
This encourages
your whiskers to
stand out, making it easier for them
to enter the cutting chamber.
Before you begin
■ Wait at least 15
12
minutes after getting
up before shaving, to
ensure your face is
free of puffiness that
may be present from
sleeping.
9
3
6
Never press hard. Pressing only flat-
tens your whiskers,
making it harder for
them to enter the
cutting chamber. It
will also wear out
■ Make sure your face is
clean and dry before
starting.
■ Always use a clean,
dry shaver.
the cutting surface
more quickly.
3. Fully extended (up), the trimmer
can be used to trim your sideburns
and mustache. Slide the trimmer
into the top position, above the
foils.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd 6-7
11/1/06 10:40:57 AM
User Maintenance
®
®
apply Remington Shaver Saver
The replacement part for this shaver
is model SP-100 (screens) and SP-
101 (screens and cutters).
U.S. residents:
To order shaver accessories call
800-231-8793, visit
or visit your local retailer.
Canadian residents:
To order shaver accessories, please
call 800-268-0425 or visit
The hand-held unit shall be detached
4. Do not separate the cutter’s blades
from the plastic pieces they are
attached to, as this may damage
the assembly.
Lubricant (SP-4). The lubricant
from the power supply cord before
cleaning. The shaver shall not be
used until it has dried.
helps remove hair clippings while
reducing wear. A quick spray after
each shave keeps your shaver
operating at peak performance.
Caution: Do not remove or replace
the head assembly while shaver is
running as it may cause damage to
the unit's foils or cutters.
When is it time to replace your
screens and cutters?
The shaver is
a washable
shaver, the
hand-held part
of which may
be cleaned
Because they are subject to daily
use, the cutters and screens of your
shaver will wear and eventually
require replacement to maintain a
close, comfortable shave. It is very
important to replace your screens
and cutters when necessary to
ensure a close, comfortable shave
without irritation.
Depending on your shaving tech-
nique and habits, the screens will
usually last 6 months; the cutters,
12 months. If you are replacing the
cutters, it’s a good idea to replace
the screens at the same time.
■ Worn or damaged parts should
be replaced with Remington
replacement parts only.
under water.
®
Replacing Cutters and Screens
To prevent inadvertent damage to the
cutters and screens, do not attempt
to remove them from the head
assembly unless you are replac-
ing them. Removal instructions are
included with the cutter and screen
replacement packages.
To replace a cutter assembly that is
removed unintentionally:
1. Hold the cutter in the middle. The
blades will not cut your fingers, so
no special handling
Cleaning your shaver:
Trimmer Care
TO ASSURE SMOOTH, EFFICIENT
PERFORMANCE, IT IS IMPORTANT TO
CLEAN YOUR SHAVER. Cleaning your
shaver is easy.
The trimmer on your shaver is easy
to maintain.
■ To clean the trimmer, you must first
turn the shaver off, and extend the
trimmer to its maximum height
(trimmer setting #3). Then, just
brush off any clippings that may
accumulate around the trimmer
assembly. Using the supplied brush
will enable you to get into the
area between the trimmer and the
shaver.
■ Every six months, lubricate the
trimmer by applying a drop of light
machine oil one-third and two-
thirds of the way along the blade.
Using your finger tip, spread the
oil along the teeth, and run the
trimmer for a few seconds.
■ After each shave, remove the
shaver head by squeezing on both
release buttons and pulling up
from the body of the shaver. Blow
out the stubble thoroughly.
Important: Never clean the foil with
the enclosed brush because damage
may occur to the holes in the foil.
■ At least once a week, the cutters
and the trimmer should be cleaned
with the cleaning brush.
Attention: Never put the shaver
completely into water. Do not use an
aggressive cleansing agent as this
may destroy the shaver coatings.
Here are some signs that your
screens and cutters need replacing:
Irritation: As screens get worn, you
may notice that your skin feels more
sensitive after a shave, particularly
when you apply aftershave.
techniques are
necessary.
2. Align the cutter so
the bar on the bottom
Pulling: As cutters wear, your shave
may not feel as close and you may
feel your shaver is pulling at your
whiskers.
meets the opening in the clip.
3. Press down on the center of the
cutter until it snaps into place. Do
not push down on the ends of the
cutter, as you may bend the cutter,
reducing its ability to cut cleanly.
■ Daily cleaning of the cutting
system is recommended to ensure
optimum shaving performance. To
clean and lubricate your shaver's
cutters and head assembly,
Wear-through: You may notice that
thecutters have worn through the
screens.
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd 8-9
11/1/06 10:40:59 AM
Disposal
Performance Guarantee
This warranty does not cover prod-
ucts damaged by the following:
■ Accident, misuse, abuse or
alteration of the product
■ Servicing by unauthorized persons
■ Use with unauthorized accessories
■ Connecting it to incorrect current
and voltage
■ Any other conditions beyond our
control
No responsibility, obligation, or liabil-
ity is assumed for the installation or
maintenance of this product.
5. Pry both of the
Full Two-Year Warranty
Battery Removal
batteries loose from
the foam adhesive
tape on the PCB.
Spectrum Brands, Inc. is a global
consumer products company with
a diverse portfolio of world-class
brands, including Remington -
When your rechargeable shaver
reaches the end of its useful life, the
batteries must be removed from the
shaver and be recycled or disposed
of properly in accordance with your
state and local requirements. If this
is not required by law, you may elect
to dispose of the shaver without
removing the batteries.
5
6. Cut or break the
wires connecting
the batteries to the PC board.
branded electric shavers. Spectrum
Brands, Inc. warrants this product
against any defects that are due to
faulty material or workmanship for
a two-year period from the original
date of consumer purchase. This
warranty does not include damage to
the product resulting from accident
or misuse.
If the product should become defec-
tive within the warranty period, we
will repair it or elect to replace it
free of charge. Return your product
and sales receipt with your name,
address and day time phone number
to: Spectrum Brands, Inc., Attention:
Consumer Services, 601 Rayovac
Drive, Madison, WI 53711. For more
information call 800-736-4648 in the
US or 800-268-0425 in Canada.
CAUTION: DO NOT PUT IN FIRE OR
MUTILATE YOUR BATTERIES WHEN
DISPOSING AS THEY MAY BURST
OR RELEASE TOXIC MATERIALS.
DO NOT SHORT CIRCUIT AS IT MAY
CAUSE BURNS. DISPOSE PROPERLY
IN ACCORDANCE WITH YOUR LOCAL
AND STATE REQUIREMENTS.
THE FOLLOWING PROCEDURE
SHOULD BE FOLLOWED FOR
BATTERY REMOVAL:
CAUTION: Make sure shaver is
unplugged before you begin, to avoid
a possible electric shock hazard.
1. Press the two side
buttons and pull
off the shaver head
assembly.
2. Remove the 2
outer screws from
inside the shaver
head. Loosen the
top assembly from
the body.
3. Pry off the back
cover of the
shaver, starting at the gap below
the shaver socket.
SPECTRUM BRANDS, INC. SHALL NOT
BE RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF FITNESS
AND MERCHANTABILITY, ARE LIMITED
IN DURATION TO TWO YEARS FROM
DATE OF ORIGINAL PURCHASE.
1
2
This warranty gives you specific
legal rights and you may also have
other rights which vary from state to
state or province to province. Some
states do not allow the exclusion or
limitation of incidental, special or
consequential damages.
KEEP ORIGINAL SALES RECEIPT AS
PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
4. Remove screws holding circut
board in place. Remove circut
board.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
32389_ms-700_IB.indd 10-11
11/1/06 10:41:02 AM
|