Owners &
Installation Manual
G36D Zero Clearance Direct Vent Gas Fireplace
MODELS: G36D-NG1 Natural Gas G36D-LP1 Propane
WARNING: Iftheinformationintheseinstructionsarenotfollowedexactly,
a fire or explosion may result causing property damage, personal injury
or loss of life.
FOR YOUR SAFETY
What to do if you smell gas:
FOR YOUR SAFETY: Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other appliance. Installation
and service must be performed by a qualified installer, service agency or
the gas supplier.
Do not try to light any appliance.
Do not touch any electrical switch:
do not use any phone in your building
Immediately call your gas supplier
from a neighbour's phone. Follow the
gas supplier's instructions.
This appliance may be installed in an aftermarket, permanently located,
manufactured home (USA only) or mobile home, where not prohibited by
local codes. This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with other gases,
unless a certified kit is used.
If you cannot reach your gas supplier,
call the fire department.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-515
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
12/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Safety Label
4
Operating
Instructions
Lighting Procedure
Shutdown Procedure
34
34
34
34
34
34
35
35
35
First Fire
Important Message
5
5
5
5
6
Aeration Adjustment
Before You Start
Normal Operating Sounds Of Gas Appliances
Copy Of The Lighting Plate Instructions
Maintenance Instructions
General Safety Information
Installation Checklist
G36D Unit Dimensions
Manufactured Mobile Home
Additional Requirements
Locating Your Gas Stove
Clearances
Mantel Leg Clearances
Framing And Finishing
Combustible Mantels
Unit Assembly Prior To Installation
Venting Introduction
Exterior Vent Termination Locations
Venting
Rigid Pipe Venting Components List
Rigid Pipe Venting Systems
Horizontal or Vertical Terminations
Rigid Pipe Venting Arrangements
- Horizontal Terminations
Rigid Pipe Venting Arrangements
- Vertical Terminations
MAINTENANCE
6
6
7
7
7
8
9
9
10
11
12
13
13
Gold-Plated or Brass Trim
Log Replacement
Thermopile / Thermocouple
Glass Gasket
36
36
36
36
36
37
37
38
39
40
Door Glass
Removing Valve
Installing Valve
G36D Main Assembly
G36D Burner Assembly & Log Set
G36D Flush Front Assembly
WARRANTY
14
The Warranty: Limited Lifetime
43
16
18
19
20
21
22
23
23
23
23
24
Vertical Termination
Venting Arrangements - Vertical Terminations
Unit Installation with Horizontal Termination
Unit Installation with Vertical Termination
Installation Procedures
High Elevation
Gas Line Installation
Pilot Adjustment
Gas Pipe Pressure Testing
Conversion Kit #773-969 From NG To LPG
Log Set Installation
27
30
31
31
31
32
33
Standard Flush Door
Option 1: Remote Control
Option 2: Wall Switch
Option 3: Wall Thermostat
Wiring Diagram
Installing The Optional Fan
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
3
Download from Www.Somanuals.com. All Manuals Search And Download.
This is a copy of the label that accompanies
each G36D Zero Clearance Direct Vent Gas
Fireplace. We have printed a copy of the
contents here for your review. The safety label
is located on the front inside base of the unit,
visible when the bottom louver is open.
NOTE: UltraGlow® units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
Wall
l l a W
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the
appliances individual manual shut-off must
be a t-handle type valve.
Model/Modele:
G36D-NG1
Model/Modele:
G36D-LP1
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
4
14) Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
CLOTHING OR OTHER FLAMMABLE
MATERIALSHOULDNOTBEPLACED
ON OR NEAR THE APPLIANCE.
15) The appliance area must be kept clear and
free of combustible materials, (gases and
other flammable vapours and liquids).
The G36D-NG1 or G36D-LP1 Direct Vent
Fireplace must be installed in accordance
with these instructions. Carefully read all the
instructions in this manual first. Consult the
"authority having jurisdiction" to determine the
needforapermitpriortostartingtheinstallation.
It is the responsibility of the installer to ensure
this fireplace is installed in compliance with
manufacturer's instructions and all applicable
codes.
INFORMATION
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
1) The appliance installation must conform
with local codes or, in the absence of local
codes,withthecurrentCanadianorNational
Gas Codes, CAN1-B149 or ANSI Z223.1
Installation Codes.
INSTALLATION
2) The appliance when installed, must be
electrically grounded in accordance with
localcodes, orintheabsenceoflocalcodes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
1) Checkallclearancestocombustibles. Refer
to the following sections:
a) Locating Your Gas Stove
b) Clearances
c) Mantel Leg Clearances
d) Combustible Mantels
e) Framing and Finishing
f) Hearth Requirement
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
3) See general construction and assembly
instructions.Theapplianceandventshould
be enclosed.
INSTALLATIONANDREPAIRSHOULD
BE DONE BY A QUALIFIED SERVICE
PERSON. THE APPLIANCE SHOULD
BE INSPECTED BEFORE USE
AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THEAPPLIANCE
BE KEPT CLEAN.
4) This appliance must be connected to the
specified vent and termination cap to the
outsideofthebuildingenvelope.Nevervent
to another room or inside a building. Make
sure that the vent is fitted as per Venting
instructions.
2) Assemble Top Standoffs and Top Facing
SupportandSideNailingStrips,Refertothe
"UnitAseemblyPriortoInstallation"section.
(NOTE: must be done before installing unit
into fireplace.)
5) Inspect the venting system annually for
3) Install vent. Refer to the "Venting"
blockage and any signs of deterioration.
section.
6) Venting terminals shall not be recessed into
4) Install standard and optional features.
Refer to the following sections where
applicable:
a wall or siding.
7) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
a. Log Set Installation
b. Standard Flush Door
c. Option 1: Remote Control
d. Option 2: Wall Switch
e. Option 3: Wall Thermostat
f. Installating the Optional Fan
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
9) Wearglovesandsafetyglassesforprotection
WARNING:FAILURETOINSTALLTHIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE
A SERIOUS HOUSE FIRE.
9) Final check.
while doing required maintenance.
Before leaving this unit with the customer,
the installer must ensure that the appliance is
firing correctly and operation fully explained
to customer
10) Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
CHILDREN AND ADULTS SHOULD
BE ALERTED TO THE HAZARDS OF
HIGH SURFACE TEMPERATURES,
ESPECIALLYTHEFIREPLACEGLASS,
AND SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
11) Under no circumstances should this
appliance be modified. Parts that have to
beremovedforservicingshouldbereplaced
prior to operating this appliance.
12) Installationandanyrepairstothisappliance
shouldbedonebyaqualifiedserviceperson.
A professional service person should be
called to inspect this appliance annually.
Make it a practice to have all of your gas
appliances checked annually.
13) Do not slam shut or strike the glass door.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
5
This includes:
5) This appliance is Listed for bedroom
installationswhenusedwithaListedMillivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
ADDITIONAL
1) Clockingtheappliancetoensurethecorrect
firing rate (rate noted on label 26,000 Btu/h)
after burning appliance for 15 minutes.
REQUIREMENTS
2) Ifrequired,adjustingtheprimaryairtoensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
6) The G36D Direct Vent Gas Fireplace is
approved for alcove installations, which
meet the clearances listed on this page.
1) Ensure that structural members are not cut
or weakened during installation.
CAUTION:Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
7) Werecommendthatyouplanyourinstallation
on paper using exact measurements for
clearances and floor protection before
actually installing this appliance. Have a
qualifiedinspector,dealer,orinstallerreview
your plans before installation.
2) Ensure proper grounding using the #8
ground lug provided. Refer to the "Wiring
Diagram" section.
Note: For vent terminations see the
"ExteriorVentTerminationLocations"
section.
1) Whenselectingalocationforyourfireplace,
ensure that the clearances outlined on this
page are met.
2) Provide adequate clearances for
servicing.
3) The appliance must be installed on a flat,
solid, continuous surface (e.g. wood, metal,
concrete).Thismaybethefloor,orraisedup
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
other combustible material other than wood
flooring, the appliance must be installed on
a metal or wood panel extending the full
width and depth of the appliance.
4) TheG36DDirectVentGasFireplacecanbe
installedinarecessedpositionorframedout
into the room as inA, B, C, D. See Diagram
1.
A) Flat on Wall
B) Flat on Wall Corner
C) Recessed into
Wall/Alcove
D) Corner
Diagram 1
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
6
2) Frame in the enclosure for the unit with
framing material. The framed opening is
37-1/4" high x 36-1/4" wide x 17-3/8" deep
(946mm high x 921mm wide x 441mm
deep).
The clearances listed below are Minimum
distances unless otherwise stated:
Combustible mantel leg clearances as per
diagram below:
A major cause of chimney related fires is
failure to maintain required clearances (air
space) to combustible materials. It is of the
greatest importance that this fireplace and
vent system be installed only in accordance
with these instructions.
Clearance to Combustibles from:
Back
Side
Floor
0"
0"
0"
(0mm)
(0mm)
(0mm)
NOTE: The minimum floor clearance must
be maintained from the top surface of the
carpeting, tile, etc.
Maximum 1-1/2" projection at 2" minimum
clearance.
Minimum Clearance from Top of Unit to:
Mantel* Minimum
7"
(177mm)
Ceiling from top of unit.
32" (1016mm)
Side Wall Clearance
Flush Front
6"
(152mm)
1) Determine the total thickness of facing
material (e.g. drywall plus ceramic tiles) to
allow the finished surface to be flush with
the front of the unit. Total facing thickness
canvaryfrom1/2"(13mm)to1-1/4"(32mm)
thick.
Horizontal Vent Clearances
Top
Side
Bottom
2-1/2" (64mm)
1-1/2" (38mm)
1-1/2" (38mm)
Vertical Vent Clearances
1-1/4" (32mm)
Framing Dimensions
Alcove Clearances**:
Max. Depth
Min. Width
A
B
C
D
36" (914mm)
48" 1219mm)
72" 1829mm)
36-1/4" 37-1/4" 17-3/8" 46-1/2"*
921mm 946mm 441mm 1181mm*
Min. Height
*'D'isMinimumheighttocombustiblematerials
including the Minimum 2-1/2" (64mm) Top
clearance to the Horizontal Vent.
* see mantle clearance instructions in the
"Combustible Mantels" section.
WARNING:
Fire hazard is an extreme risk if
these clearances are not adhered to.
3) For exterior walls, insulate the enclosure to
the same degree as the rest of the house,
apply vapour barrier and drywall, as per
local installation codes. (Do not insulate
the fireplace itself.)
It is of greatest importance that this
fireplace and vent system be
installed only in accordance with
these instructions.
4) The top of the unit must not be closer than
32" (813mm) to the ceiling.
Install Side Nailing Strips, Top Facing
Support, and Top Standoffs before unit
is slipped into position. See the "Unit
Aseembly Prior to Installation" section for
assembly details.
The HeatWave Duct Kit has different clearance and framing
requirements, check the HeatWave manual for details.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Because of the extreme heat this fireplace emits, the mantel clearances are critical.
Combustible mantel clearances from top of unit are shown in the diagram below.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered
with a non-combustible board.
These drawings are to scale at 1:6 (one inch = 6 inches)
Mantel can be installed anywhere in shaded area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Top Header
3) Attach the standoff securely to the top
with 2 screws per standoff (on opposite
corners).
10" dia. hole
through wall
for Flex
1/2"
Drywall
or for DuraVent
"C" Screw Position:
For a facing material depth of 1-1/4"
(32mm), the top facing support must be
reversed.
2"
3-1/2" 4"
Opening for gas
connection
17-1/8"
Note: 40-1/2" (1029mm) is the minimum
height for both flex termination or
Simpson Dura-Vent venting.
Top Facing Support and
Side Nailing Strips
5) The unit does not have to be completely
enclosed in a chase. The clearance on
top of the unit is 0" to the standoffs so
combustible building materials can be
laid directly on top of the standoffs. You
must maintain clearance from the vent to
combustible materials for flex, see section
"Clearances."
Determine the total thickness of facing material
(e.g. drywall plus ceramic tiles) to allow the
finished surface to be flush with the front of the
unit. Total facing thickness can vary from 1/2"
(13mm) to 1-1/4" (32mm) thick.
TheTopFacingSupport&SideNailingStripscan
be mounted in 3 different positions depending
on the thickness of the facing material.
2) Use the same screw hole position for the
Side Nailing Strips as was used for the Top
Facing Support. Attach each side nailing
strip using 3 screws.
6) Use steel studs for framing where the
1-1/2" (38mm) clearance from the vent to
combustiblematerialcannotbemaintained,
e.g. front top header.
Screw
Position
Facing Material
Depth
A
B
C
1/2"
7/8"
1-1/4"
/ 13mm
/ 22mm
/ 32mm
INTRODUCTION
INSTALLATION
The G36D uses the "balanced flue" technology
Co-Axial system. The inner liner vents products
ofcombustiontotheoutsidewhiletheouterliner
drawsoutsidecombustionairintothecombustion
chamber thereby eliminating the need to use
heatedroomairforcombustionandlosingwarm
room air up the chimney.
For "C" screw position the top facing support
is reversed.
TheTop Facing Support, the Side Nailing Strips
and the 2 Top Standoffs must be correctly
positioned and attached to the top before unit
is slipped into position.
1) Mount Top Facing Support using the 3
suppliedscrewsintothethreepre-punched
screw holes on the top front of the unit. Use
hole positionsA, B, or C depending on your
facing depth.
Top Standoff Assembly
Note: These flue pipes must not be
connected to any other appliance.
The top standoffs are shipped in a flat position
and must be folded into shape and attached.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Eachdirectventgasappliancemustuseit'sown
separate vent system. Common vent systems
are prohibited.
1) Remove the standoffs from the fireplace
top.
2) Takeeachstandoffandbendintothecorrect
shape. Bend up at the bend lines until the
screw holes in the standoff and the pre-
punched screw holes on the fireplace top
line up.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
9
EXTERIOR VENT TERMINATION LOCATIONS
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
10
® Direct Vent System (Flex)
Horizontal Terminations Only
These venting systems, in combination with the G36D Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by
Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in the "Exterior Vent
Termination Locations" section.
® Direct Vent Flex Termination Kit (Part # 946-515) includes all the parts
needed to install the G36D with a maximum total run of 4 feet.
1) 6-7/8" dia. flexible liner (4 ft. length)
2) 4" dia. flexible liner (4 ft. length)
3) spring spacers (4)
4) thimble (2)
5) AstroCap termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" Drill Point, Stainless Steel (4)
Notes:
1) Liner sections should be continuous without any joints or seams.
2) Only Flex pipe purchased from Regency® may be used for Flex installations.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
11
All Simpson Dura-Vent components are available directly from FPI.
Description
Simpson Dura-Vent
Direct VentGS®
Selkirk
Amerivent®
Direct Vent
Security
Direct-TempTM
Secure Vent®
6" Pipe Length, Galvanized
6" Pipe Length, Black
7" Pipe Length, Galvanized
7" Pipe Length, Black
9" Pipe Length, Galvanized
9" Pipe Length, Black
12" Pipe Length, Galvanized
12" Pipe Length, Black
18" Pipe Length, Galvanized
18" Pipe Length, Black
24" Pipe Length, Galvanized
24" Pipe Length, Black
36" Pipe Length, Galvanized
36" Pipe Length, Black
48" Pipe Length, Galvanized
48" Pipe Length, Black
908
908B
N/A
N/A
907
907B
906
906B
N/A
N/A
904
4DT-6
4DT-6B
N/A
N/A
4DT-9
4DT-9B
4DT-12
4DT-12B
4DT-18
4DT-18B
4DT-24
4DT-24B
4DT-36
4DT-36B
4DT-48
4DT-48B
N/A
N/A
4D7
4D7B
N/A
SV4L6
SV4LB6
#N/A
#N/A
#N/A
N/A
#N/A
4D12
4D12B
N/A
N/A
4D2
4D2B
4D3
4D3B
4D4
SV4L12
SV4LB12
SV4LA
SV4LA
SV4L24
SV4LB24
SV4L36
SV4LB36
SV4L48
SV4LB48
904B
903
903B
902
902B
4D4B
Adjustable Length, 11"-14", Galv.
Adjustable Length, 11"-14", Black
Adjustable Length, 17"-24", Black
Adjustable Length, 7" Galvinized
Adjustable Length, 7" Black
911
4DT-AJ
4DT-AJB
N/A
N/A
N/A
N/A
N/A
N/A
4D7A
4D7AB
4D12A
4D12AB
#N/A
#N/A
SV4LBA24
#N/A
#N/A
911B
917B
N/A
N/A
N/A
Adjustable Length, 12" Galvinized
Adjustable Length, 12" Black
N/A
N/A
SV4LA12
SV4LBA12
N/A
45O Elbow, Galvinized
45O Elbow, Black
945
4DT-EL45
4DT-EL45B
N/A
4D45L
4D45LB
N/A
#N/A
#N/A
945B
945G
945BG
990
990B
990G
990BG
45O Elbow, Swivel, Galvinized
45O Elbow, Swivel, Black
90O Elbow, Galvinized
90O Elbow, Black
SV4E45
SV4EB45
#N/A
SV4EBR90-1
SV4E90-1
SV4EB90-1
N/A
N/A
4DT-EL90S
4DT-EL90SB
N/A
4D90LS
4D90LBS
N/A
90O Elbow, Swivel, Galvinized
90O Elbow, Swivel, Black
N/A
N/A
Ceiling Support
Cathedral Support Box
Wall Support/Band
Offset Support
Wall Thimble, Black
Wall Thimble Support Box/Ceiling Support
Firestop Spacer
Trim Plate, Black
949 - n/a from FPI
941
988
4DT-CS
4DT-CSS
4DT-WS/B
4DT-OS
4DT-WT
N/A
4DT-FS
4DT-TP
N/A
4DFSP
4DRSB
4DWS
N/A
4DWT
N/A
4DFSP
4DFPB
N/A
SV4SD
SV4CSB
SV4BM
SV4SU
SV4RSM
SV4PF
SV4BF
SV4LA
#N/A
989 - n/a from FPI
942
940
963
N/A
3951
Brass Trim for Wall Thimble/Ceiling Support
Attic Insulation Shield 12"
Attic Insulation Shield - Cold Climates 36"
N/A
N/A
N/A
N/A
4DAIS12
4DAIS36
SV4RSA
#N/A
Basic Horizontal Termination Kit (A)
Horizontal Termination Kit (B)
Vertical Termination Kit
970
971
978
4DT-HKA
4DT-HKB
4DT-VKC
4DHTK2
4DHTK1
4DVTK
SV - SHK
SV - HK
SV - FK
High Wind Vertical Cap
High Wind Horizontal Cap
Horizontal Square Termination Cap
Verical Termination Cap
Storm Collar
991
985
984
980
953
N/A
N/A
4DT-HHC
4DT-HVC
4DT-SC
N/A
N/A
4DHC
4DVC
4DSC
#N/A
#N/A
SV4CHC-1
SV4CGV-1
SV4FC
Adjustable Flashing, 0/12-6/12
Adjustable Flashing, 6/12-12/12
943
943S
4DT-AF6
4DT-AF12
4DF
4DF12
SV4FA
SV4FB
Vinyl Siding Standoff
Vinyl Siding Shield Plate
950
N/A
4DT-VS
4DT-VSP
N/A
N/A
SV4VS
SV4VS
Snorkel Termination 14"
Snorkel Termination 36"
982
981
4DT-ST14
4DT-ST36
4D12S
4D36S
SV4STC14
SV4STC36
FPI
946-506/P
510-994
946-205
Vinyl Siding Shield for Riser Vent Terminal
Vent Guard (Optional) - Riser Vent Terminal
AstroCap Horizontal Cap
Vent Guard (Optional)
Rigid Pipe Adaptor (Must use with all Rigid Piping)
Riser Vent Terminal
946-208/P
946-523/P
946-206
640-530/P
Vinyl Siding Standoff - AstroCap
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Horizontal or Vertical Terminations
The minimum components required for a basic horizontal termination
Flat Wall Installation
are:
Wall Thickness
Vent Length Required
(inches)
(inches)
4" - 5-1/2"
7" - 8-1/2"
10" - 1-1/2"
9" - 14-1/2"
15" - 23-1/2"
1
1
1
1
1
Horizontal Termination Cap
90o Elbow
Rigid Pipe Adaptor
Wall Thimble
Length of pipe to suit wall thickness (see chart)
6"
9"
12"
11" - 14-5/8" Adj. Pipe
17" - 24" Adj.
Wallthickness ismeasuredfromthebackstandoffstotheinsidemounting
surface of termination cap. For siding other than vinyl furring strips may
be used, instead of the vinyl siding standoff, to create a level surface to
mount the vent terminal. The Terminal must not be recessed into siding.
Measure the wall thickness including furring strips.
Corner Installation
Wall Thickness
(inches)
Vent Length Required
(inches)
If a Vinyl Siding Standoff is required (it must be used with vinyl siding),
measure to outside surface of wall without siding and add 2 inches.
3-1/4" - 6-3/4"
7-3/4" - 16-1/4"
7-1/4" - 8-3/4"
11" - 14-5/8" Adj. Pipe
17" - 24" Adj. Pipe
6" + 12"
9" + 9"
Vertical
Terminal
4-1/4" - 5-3/4"
6" + 9"
Storm Collar
(Part # 953)
Vinyl Siding
Standoff (Optional)
(Part #950)
Alternate
Flashing
Horizontal Ter-
mination Caps
943 or 943S
Ceiling Firestop
(Part # 963)
Horizontal
Termination Cap
(Part# 946-523/P)
Wall Thimble
(Part # 942)
Pipe Length
Adj.Pipe Length
11" - 14-5/8"
90o Elbow
WARNING:
Do not combine venting components from
different venting systems.
24" Pipe
Length
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.
Rigid Pipe Adaptor
(Part# 510-994)
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Dura-Vent Direct Vent GS, Selkirk Direct-
Temp, Ameri Vent Direct venting and Security
SecureVentsystems.Useofthesesystemswith
the Rigid Pipe adaptor is deemed acceptable
and does not affect the Intertek WHI listing of
components.
When using Rigid Vent piping other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent GS,
American Metal Products Ameri Vent Direct Vent and Selkirk Direct-Temp. AstroCapTM is the proprietary trademark of FPI Fireplace Products International
Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
13
® DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o elbow (two 45o elbows equal one 90o
elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid vent systems.
All Rigid Pipe Systems
4" inner diameter
6-5/8" outer diameter
® Flex Vent
4" inner diameter
6-7/8" inner diameter
A vent guard should be used
whenever the termination is lower
than the specified minimum or as
per local codes.
Note: UltraGlow® Direct Vent System
(Flex) is only approved for
horizontal terminations.
•
Maintain clearances to combustibles as listed in the "Clearances," "Mantel Leg Clearances," "Framing and Finishing," & "Combustible
Mantels" sections.
•
•
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
14
Download from Www.Somanuals.com. All Manuals Search And Download.
UltraGlow® DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
The diagram below shows examples of horizontal termination arrangements using two 90o elbows (two 45o elbows equal one 90o elbow).
Note:
1) A maximum of two 90o elbows are permitted.
2) A minimum of 6 ft. (1.8m) vertical from base of unit is required if two 90o elbows are used.
3) Minimum distance between elbows is 2 ft. (0.6m).
4) Determine the permitted range of horizontal termination arrangements by using chart in the "Rigid Pepi Venting
Arrangements - Vertical Termination" section and deducting 3 ft. (0.9m) from the maximum horizontal distance for the
second 90o elbow.
Iflength"B"isincreased,length"A"mustbe
decreased by a corresponding amount.
All Rigid Pipe Systems
4" inner diameter
6-5/8" outer diameter
® Flex Vent
4" inner diameter
6-7/8" inner diameter
A vent guard should be used whenever the
terminationislowerthanthespecifiedminimum
or as per local codes.
•
•
Maintain clearances to combustibles as listed in the "Clearances," "Locating Your Gas Stoves," "Combustible Mantels," "Framing
and Finishing," & "Hearth Requirement" sections.
Horizontal vent must be supported every 3 feet.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
15
RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
(Propane & Natural Gas)
The G36D is approved for a maximum 23 ft. (7.0m) vertical, with a maximum 12 ft. (3.7m) horizontal offset
using two 90o elbows (two 45o elbows equal one 90o elbow) with Rigid Pipe vent systems for Propane and
Natural Gas, as per diagram 1.
TheG36Disapprovedfora maximum37ft. (11.3m)straightvertical, includingamaximum20"(0.5m)horizontal
offset using two 90o elbow (two 45o elbows equal one 90o elbow) with Rigid Pipe vent systems for Propane
and Natural Gas, as per diagram 2.
•
•
•
Vent must be supported at offsets
Maintain clearances as listed in the"Clearances" section.
Firestops are required at each floor level and whenever passing through a wall.
Note: Must use optional rigid pipe adaptor when using rigid vent systems (Part # 510-994).
® Direct Vent System (Flex) is only approved for horizontal terminations.
Diagram 2
Diagram 1
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TheG36Disapprovedforamaximum37ft.(11.3m)straightvertical,withRigid
Pipe vent systems for Propane and Natural Gas, as per the diagram 3.
The shaded area in the diagram 3 shows all allowable combinations of straight
vertical and offset to vertical terminations with Rigid Pipe vent systems for
Propane and Natural Gas. Maximum two 45o elbows allowed.
•
•
Vent must be supported at offsets
Firestops are required at each floor level and whenever passing
through a wall.
•
Maintain clearances to combustibles as listed in the "Clearances"
section.
Diagram 3
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
17
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements on next page for minimum and
maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
Required Parts:
A maximum
of two certified
joiner kits
may be used
per length.
#948-305 (35 ft)
Part #
Description
946-529
Co-linear DV Vertical
Termination Cap
948-305
946-563
Kit
3" Flex - 35 ft.
Co-Axial to Co-Linear Adapter
Flex Liner
which contains the following:
Co-linear Flex Adapter
Outer Pipe
Inner Pipe Adapter
Rigid Pipe Adaptor
510-994
Alternate Approved Caps
Exhaust
Flue
980
991
Vertical Termination Cap
High Wind Cap
923GK 3" Co-linear Adapter with flashing
Outer
Pipe
with Kit#
946-563
FPI Cabinet and/or Flat Wall Mantles
may be used in these applications
ensuring that clearances to
Air Intake
combustibles are maintained.
Pipe Length
Co-Linear
Flex
Adapter
with Kit#
946-563
Rigid Pipe Adaptor
# 510-994
90 Degree
Elbow
Inner Pipe
Adapter
with Kit#
946-563
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
18
VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagrams show the
allowable vertical terminations.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
19
UNIT INSTALLATION
b) Horizontal runs of vent must be
supported every three feet. Wall straps
are available for this purpose.
5) Mark the wall for a 10" x 10" square hole.
The center of the square hole should line
upwiththecenterline ofthehorizontal pipe.
Cut and frame the 10 inch square hole in
the exterior wall where the vent will be
terminated. If the wall being penetrated is
constructedofnon-combustiblematerial,i.e.
masonry block or concrete, a 7"(178mm)
dia. (7-1/2"(191mm) dia. for flex) hole is
acceptable.
Install the vent system according to the
manufacturer's instructions included with
the components.
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
Note: Riser Vent
is only for use
in above grade
terminations.
Note: With Dura-Vent,
the minimum
h e i g h t i s
achieved by
i n s t a l l i n g
a 90o elbow
directly to
the rigid pipe
adaptor.
Diagram 3a
2) DirectVentpipeandfittingsaredesignedwith
specialtwist-lockconnectionstoconnectthe
ventingsystemtotheapplianceflueoutlet.A
twist-lock appliance adaptor is an available
option that must be used in conjunction
with the Simpson Dura-Vent Direct Vent GS
system.
*Diagrams 3 & 4: As specified in CGA B149
InstallationCode.Localcodesorregulations
may require different clearances.
3) Putabeadofsiliconeinsidetheoutersection
of the adapter and a bead of Mill Pac on the
innercollar.Sliptheadapterovertheexisting
inner and outer flue collar and fasten to the
outer collar only with the 3 supplied screws
(drilling pilot holes will make this easier).
Levelthefireplaceandfastenittotheframing
using nails or screws through the nailing
strips.
Diagram 2
Note:
a) The horizontal run of vent must be
level, or have a 1/4 inch rise for every
1 foot of run towards the termination.
Never allow the vent to run downward.
Thiscouldcausehightemperaturesand
may present the possibility of a fire.
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
b) The location of the horizontal vent
terminationonanexteriorwallmustmeet
alllocalandnationalbuildingcodes,and
must not be blocked or obstructed. For
External Vent Terminal Locations, see
diagraminthe"ExteriorVentTermination
Locations" section.
Note:
a) Twist-lockprocedure:Fourindentations,
located on the female ends of pipes and
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends,Diagram1.Pushthepipesections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
c) Snorkel Terminations:
For installations requiring a vertical
rise on the exterior
of the building, 14-
inch and 36-inch tall
Snorkel Terminations
are available,
as well as the
standard Riser
Vent. Follow
the same
installation
procedures
NOTE: For Snorkel terminations in ABOVE
grade installations, follow national
or local code requirements.
as used for
s t a n d a r d
Horizontal
Termination.
NEVER install
the snorkel
upsidedown.
6) The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials
are maintained (Diagram 4). Install the
termination cap.
Diagram 1
Note: Apply sealant "Mill-Pac" to inner
pipe and high temperature silicone
sealant to outer pipe on every twist-
lock joint.
Diagram 3
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
20
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
TERMINATION
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/2". Slip the flashing
under the shingles (shingles should overlap
half the flashing) as per Diagram 4.
1) Maintain the 1-1/2" clearances
(air spaces) to combustibles
when passing through ceilings,
walls, roofs, enclosures,
attic rafter, or other nearby
combustible surfaces. Do not
pack air spaces with insulation.
Check the "Venting" section for
the maximum vertical rise of
the venting system and
Diagram 5
the maximum horizontal
offset limitations.
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
2) Setthegasapplianceinits
desired location. Drop a
plumb bob down from the
ceiling to the position of
theapplianceflueexit,andmarkthelocation
wheretheventwillpenetratetheceiling.Drill
a small hole at his point. Next, drop a plumb
bobfromtherooftotheholepreviouslydrilled
in the ceiling, and mark the spot where the
vent will penetrate the roof.
Determine if ceilingjoists,
roof rafters or
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
Diagram 4: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed. This
allows for small adjustments.
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble (Part # 942) over the vent pipe.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic
to avoid obstructions, it is important
to support the vent pipe every 3 feet,
to avoid excessive stress on the
elbows, and possible separation.
Wall straps are available for this
purpose (Diagram 2).
other framing
will obstruct
the venting
system. You
may wish to
relocate the
a p p l i a n c e
or to offset,
as shown in
Diagram 2 to
avoid cutting
load bearing
8) Slide the appliance and vent assembly
towards the wall carefully inserting the
vent pipe into the vent cap assembly. It is
important that the vent pipe extends into
the vent cap sufficient distance so as to
result in a minimum pipe overlap of 1-1/4
inches. Secure the connection between the
vent pipe and the vent cap by attaching the
two sheet metal strips extending from the
vent cap assembly into the outer wall of the
vent pipe. Use the two sheet metal screws
provided to connect the strips to the pipe
section. See Diagram 6.
Galvanized pipe is desirable above the
rooflineduetoitshighercorrosionresistance.
Continue to add pipe sections through the
flashinguntiltheheightoftheventcapmeets
the minimum height requirements specified
in Diagram 5 or local codes. Note that for
Diagram 2
members.
Note: Applysealant"Mill-Pac"toinnerpipe
and high temperature silicone seal-
ant to outer pipe on every twist-lock
joint.
Diagram 5
Roof Pitch
Minimum Vent Height
Feet
2
Meters
0.61
0.61
0.61
0.76
0.99
1.22
1.52
1.83
2.13
2.29
2.44
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut a
10inchsquarehole.Frametheholeasshown
in Diagram 3 and install the firestop.
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
2
2
Diagram 6
2.5
3.25
4
9) Install wall thimble in
the center of the 10"
square and attach
with wood screws
(Diagram 7).
5
6
7
7.5
8
Diagram 3
Diagram 7
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
21
4) Separatethe2halvesofthewallthimbleand
securely fasten the one with the tabs to the
outside wall making sure that the tabs are
on top and bottom. Fasten the other thimble
half to the inside wall. The thimble halves
slip inside each other and can be adjusted
for 2 x 4 or 2 x 6 walls. The liners must slip
over the collars a minimum of 1-3/8".
steep roof pitches, the vertical height must
be increased. A poor draft, or down drafting
can result from high wind conditions near big
trees or adjoining roof lines, in these cases,
increasing the vent height may solve the
problem.
Note: To make
the installation
more aesthetically
p l e a s i n g ,
w e
recommend framing
outasquaretomount
the terminal to.
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
5) Slip the assembled liner and termination
assembly through the thimble making sure
the termination cap faces up (there are
markings on the cap that show which way
is up). This will position the termination cap
with proper down slope for draining water.
Fasten the cap to the outer wall with the 4
supplied screws.
8) Install the vertical termination cap by twist-
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination
is not recessed into the siding.
locking it.
Note: Anyclosetsorstoragespaces,which
the vent passes through must be
enclosed.
2) Levelthefireplaceandfastenittotheframing
using nails or screws through the nailing
strips.
6) Pull the centre 4"(100mm) liner and outer
6-7/8"(175mm) liner out enough to slip over
the flue collars of the fireplace. (You may
wish to cut the liner shorter to make it more
workable.) Do not bend liner more than
90o
Offset Chart
3) Assemble the vent assembly by applying
Mill Pac to the 4"(100mm) inner collar of the
terminationand slippingthe4"(100mm)liner
over it at least 1-3/8" (35mm). Fasten with
the3screws(drillingpilotholeswillmakethis
easier). Apply Mill Pac or high temperature
silicone to the 6-7/8"(175mm) flex pipe and
slip it over the 6-7/8" outer collar of the vent
terminal at least 1-3/8"(35mm) and fasten
with the 3 screws.
7) Apply Mill Pac over the fireplace inner collar
and slip the 4"(100mm) liner down over it
and attach with 3 supplied screws.
8) Do the same with the 6-7/8"(175mm) liner.
9) Applyabeadofsiliconebetweenthethimble
and termination and around the outer edge
of the terminal at the wall in order to keep
the water out.
NOTE: Horizontal sections must be
supported at intervals not exceeding
3 feet (0.9 meter). (Flame picture and
performance will be affected by sags
in the liner).
IMPORTANT: Do not locate termination
hood where excessive snow or ice
buildup may occur. Be sure to check vent
terminationareaaftersnowfalls, andclear
to prevent accidental blockage of venting
system. When using snow blowers, make
sure snow is not directed towards vent
termination area.
INSTALLATION
® Direct Vent
System (Flex)
1) Locate the unit in the framing, rough in the
gas (preferably on the right side of the unit)
and the electrical (Junction block is on the
left side) on the left. Locate the centerline of
the termination and mark wall accordingly.
Cut a 10"(254mm) hole in the wall (inside
dimension).
Note: A 1-1/2"(38mm) clearance around
the liner must be maintained except
that only a 1" (25mm) clearance is
needed at the termination end. We
recommend framing a 10"(254mm)
x 10"(254mm) (inside dimensions)
hole to give structural rigidity for
mounting the termination.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
22
The manifold pressure is controlled by a
regulator built into the gas control, and should
be checked at the pressure test point.
alwaysbesttoconsultwithyourlocalauthorities
and the CAN/CGA B149 installation code.
G36D-NG1 System Data
For 0 to 4500 feet altitude
For USA installations follow local codes and/or
the current National Fuel Gas Code, ANSI
Z223.1.
Burner Inlet Orifice Sizes:
#42
Note:Toproperlycheckgaspressure,both
inletandmanifoldpressuresshould
becheckedusingthevalvepressure
ports on the valve.
Max. Input Rating 26,000 Btu/h
Min. Input Rating 13,100 Btu/h
When using copper or flex connectors use only
approved fittings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and flex
connectors are usually considered to meet this
requirement.
Supply Pressure
min.5.0" w.c.
1) Make sure the valve is in the "OFF"
position.
Manifold Pressure
(High)
3.8"+/- 0.2"w.c.
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a
1/8" wide flat screwdriver.
Log Set: Ceramic fibre, 7 per set.
Vent System: Simpson Dura-Vent Direct
Vent System or UltraGlow® Direct
Vent System (Flex)
Important:Alwayscheckforgasleakswitha
soapandwatersolutionorgasleakdetector.
Do not use open flame for leak testing.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
G36D-LP1 System Data
Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile, 1 around
the thermocouple and 1 flowing across the
burner (it does not have to be touching the
burner).
5) The pressure check should be carried out
withtheunitburningandthesettingshould
be within the limits specified on the safety
label.
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#53
Max. Input Rating 26,000 Btu/h
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Note: Screw should be
snug, but do not over tighten.
Min. Input Rating 13,800 Btu/h
Note: Ifyouhaveanincorrectflamepattern,
contact your Regency® dealer for
further instructions.
Supply Pressure
min.12.0" w.c.
11"+/- 0.2" w.c.
Manifold Pressure
(High)
S.I.T. VALVE DESCRIPTION
Log Set: Ceramic fibre, 7 per set.
Vent System: Simpson Dura-Vent Direct
Vent System or UltraGlow® Direct
Vent System (Flex)
1) Gas on/off knob
2) Manual high/low adjustment
3) Pilot Adjustment
4) Thermocouple Connection - option
5) Outlet Pressure Tap
6) Inlet Pressure Tap
7) Pilot Outlet
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or
thermopile or thermocouple.
8) Main Gas Outlet
9)
ve TC Connection
This unit is approved in Canada for altitude 0
to 4500 ft. (CAN1 2.17-M91) with the orifice
supplied.
GAS LINE
The gas line can be brought through either the
right or the left side of the appliance. The gas
valve is situated on the right hand side of the
unit and the gas inlet is on the right hand side
of the valve.
Note: If the gas line is being installed from
the left side, be sure to leave room to
accommodate servicing of the fan.
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnectpipingfromvalveatpressures
over 1/2 psig.
The gas line connection may be made of rigid
pipe,copperpipeoranapprovedflexconnector.
(Ifyouareusingrigidpipe,ensurethatthevalve
can be removed for servicing.) Since some
municipalities have additional local codes it is
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
23
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!
11) Remove the black protection cap by
hand from the high-low knob (Fig.1).
Each Kit contains one LPG
Conversion Kit and one DC
Sparker Kit.
LPG Conversion Kit Contains:
Qty. Part #
Description
Remove the 2 screws, push Burner
Assembly to the left and lift out.
1
1
1
904-345
908-528
908-255
Burner Orifice #53
Red "LPG" label
Label "Converted to
LPG
1
1
1
908-529
910-037
918-476
5/32" Allen Key
LP Injector (Pilot Orifice)
Instruction Sheet
6) Pull off the pilot cap to expose the pilot
orifice
DC Sparker Kit Contains:
Qty. Part # Description
12) Insert a 5/32 or 4mm Allen wrench into
the hexagonal key-way of the screw
(Fig. 2), rotate it counter-clockwise until
it is free and extract it
1
1
1
1
1
820-475
Bracket DC Sparker
Bracket DC Sparker
Washer #8 External Star
Nut 8-32 Hex
820-476
904-153
904-330
904-438
Plug Nylon 0.750 Hole,
Black
2
1
2
1
1
1
904-531
904-543
904-553
910-073
910-074
910-078
Bushing Split Plastic
0.500 in
Screw 8-32 x 3/4 Pan
Head
7) Unscrew the pilot orifice with the allen
key and replace with the LP pilot orifice
in the kit and replace pilot cap.
Screw #8 x 1/2 Type "B",
Black Oxide
Spark Generator Battery
Holder
Spark Generator Switch
C/W Wire
Battery Size AA
Energizer En91
1
1
910-199
910-903
Clip Wire Holder
Wire Fan To Power Cord
Ground 30 in
1
910-480
904-781
904-782
Instruction Sheet
Velcro Hook, Black
Velcro Hook, Black
13) Check that the screw is clean and if
necessary remove dirt.
8) Remove burner orifice with a 1/2"
wrench and discard. Use another wrench
to hold on to the elbow behind the
orifice
Installation of LPG
Conversion Kit:
14) Flip the screw (Fig. 3).
1) Shut off the gas supply
2) Remove the louvers (and bay door if it is
installed)
3) Open the flush door and remove the
door
4) Remove the logs and embers
5) Remove the 2 screws holding the Burner
Assembly to the firebox base. Push the
Burner Assembly to the left and lift out
9) Reinstall new burner orifice LP stamped
#53 and tighten
10) Turn control knob to the OFF position
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
24
15) Using the Allen wrench as shown in
Fig.4, rotate the screw clockwise until
snug, do not overtighten.
24) Install the 3/4" nylon plug to cover up the
hole on the mounting bracket.
WARNING!
Also check that the pilot
and main burner injectors are
appropriate for the gas type.
18) Reverse steps 5) to 2)
19) Attach the label "This unit has been
converted to LPG" near or on top of the
serial # decal.
20) Replace yellow "Natural Gas" label with
red "Propane" label.
Fig.4
25) Connect the DC spark generator wires
to the SIT Valve with the screw which is
provided in the kit.
WARNING!
Do not overtighten the screw
Recommended to
21) Locate the Piezo Ignitor situated at the
side of valve.
grip the wrench by
the short side.
Piezo
Ignitor
16) Verify that if the conversion is from
NG to LPG, the screw
assembled with the red o-ring visible
(Fig. 5)
22) Remove the Piezo Ignitor by unscrewing
the nut at the back of the mounting
bracket.
26) Locate the ground lug at the receptical
box, left of the unit.
Ignitor
Wire
17) Re-assemble the black protection cap
(Fig. 6)
Piezo
Ignitor
23) Disconnect the ignitor wire from the
Piezo Ignitor and connect it to the D.C.
Sparker
27) Connect one end of the supplied green
ground wire to the lug with the nut and
washer from the kit.
DC
Sparker
Ground
wire from
kit
Ignitor
Wire
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
25
28) Install the 1/2" bushing to the heat 32) Mount the heat shield to the DC Sparker
shield.
Secure into place with the velcro, which
is provided in the kit.
29) Run the other end of the ground wire
and DC spark generator wires through
the bushing on the heat shield.
33) Find a location which is not too hot and
is easy to reach for changing the battery.
Note: It should be kept away from the
chain.
Heat Shield
Chain
30) Plug the DC spark generator wires to the
DC Sparker
34) Tie up the loose wire with the wire clip.
31) Connect the ground wire to the DC
Sparker mounting bracket.
35) Check for gas leaks.
36) Check inlet and outlet pressures.
37) Check operation of flame control.
38) Check for proper flame appearance and
glow on logs.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken
logs can interfere with the pilot operation.
The gas log kit (Part # 780-930) contains the following pieces:
a) 02-75 Rear Log
b) 02-55 Middle Left Log
02-75
02-51
c) 02-50 Front Left Log
d) 02-53 Center Left Log
e) 02-51 Front Bottom Log
f) 02-54 Center Right Log
g) 02-52 Middle Right Log
h)
i)
Embers
Vermiculite
902-156
902-179
02-55
02-52
02-75
Bracket
Bracket
02-51
Notch
02-50
02-53
02-54
02-51
5) Position Log 02-53 across the cutouts in Logs 02-75 and 02-51 with
The "02" refer numbers (i.e. 02-75) are
molded into the rear of each log.
the notch on the left side of the log fitting into the 2nd grate tab.
1) Carefully remove the logs from the box and unwrap them. The logs
are fragile, handle with care - do not force into position.
02-53
2) Sprinkle the vermiculite all over the top of the base brick panel.
3) Place Log 02-75 on the rear log support pins with the flat side to the
02-75
02-51
back.
2nd Grate Tab
Cutouts
02-75
02-51
Support Pins
4) Place Log 02-51 on the front right side of the burner. Push the back
of the log against the 2 brackets with the notch on the bottom right
side of the log fitting into the right side of the grate.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
27
Download from Www.Somanuals.com. All Manuals Search And Download.
8) PlaceLog02-52betweenLogs02-51and02-75andontheindentation
6) Position Log 02-54 across the cutouts in Logs 02-51 and 02-53. The
on Log 02-54. The bottom right end sits behind the rear grate tab.
notch in the bottom right end fitting against the 5th grate tab.
02-75
02-52
02-54
02-51
02-51
02-54
Log indentation
Photo shows rear grate tab. Log
02-51 was removed to show the
positioning of Log 02-52.
02-54
Rear
Grate Tab
5th Grate Tab
9) Sit Log 02-50 on the front left side of the burner. Push the back of
the log against the 2 front brackets with the notch on the bottom of
the log fitting into the first grate tab.
7) Place the bottom left front edge of Log 02-55 against the rear bracket
on the burner tray and rest the log on the cutout on Log 02-53.
02-75
02-55
02-51
Front Brackets
02-55
Rear Bracket
Cutouts
02-50
Notch
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
28
Download from Www.Somanuals.com. All Manuals Search And Download.
10) Place the embers on the front of the burner tray in the places shown
11) Test fire to ensure proper light off (make sure flame flows smoothly
from one end of burner to the other). If there is any flame hesitation,
check that area for any blockage of the burner ports.
on the photos below.
12) Install flush glass as per instructions in manual.
Place embers in these 3 locations
on the burner tray.
02-51
02-54
Do not block the burner holes in this area
adjacent to the Log 02-54
02-75
02-55
02-51
02-50
02-54
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the hook to pull the spring out until you
can put the hook into the slot on the bottom
door bracket. Repeat for 2nd spring. See
diagram 3.
Flush Louvers
DOOR
1) Install each top by clipping the louver lip
onto the top louver brackets ensuring that
each individual louver is centered from side
to side.
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, diagram 1.
2) The bottom louver has a hinge that is
attached (2 screws per hinge) to the lip on
bottom of the unit.
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace and position the slots in the
bracket over the 2 screws on the left side
of the bottom louver. Push down to lock into
place. Tighten the screws.
Diagram 3
To remove the flush door, reverse the above
steps.
Optional Flush Trim
Attach the round magnets to the back of the
top trim piece and to the bottom trim piece,
then attach trim to the top and bottom of Flush
door.
Diagram 1
Note: Top and bottom louvers are
different.
Be careful that the glass gasket does not roll up;
there must be a gap between the gasket and
the door lip to ensure that the door sits securely
on the unit. Diagram 2.
Diagram 2
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
30
REMOTE CONTROL
Option 2:
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram.
Use the table below to determine the maximum
wire length.
UsetheU® RemoteControlKit approved
for this unit. Use of other systems may void
your warranty.
1) Runthewirethroughtherightorleftsideinlet
opening. Be careful not to damage wire.
Note: We recommend a maximum of 15'
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
Note:Preferableifthethermostatisinstalled
on an interior wall.
The remote control kit comes with a hand held
transmitter, a receiver and a wall mounting
plate.
UltraGlow® offers an optional programmable
thermostat or basic wall thermostat but any
250-750 millivolt rated non-anticipator type
thermostat that is CSA, ULC or UL approved
may be used.
2) Connectthewiretothewallswitchandinstall
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace
to that location. Use the Thermostat Wire
Table.
into the receptacle box.
CAUTION
Do not connect millivolt
to a 120V wire.
2) Connect the two wires to the gas valve. See
diagram below.
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
Do not connect millivolt remote
control wires to a 120V wire.
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
3) Install3AAAalkalinebatteriesintransmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
31
This heater does not require a 120VA.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat
will continue to operate.
(Do not cut the ground terminal off under any circumstances.)
Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.
CAUTION: Label all wires prior
to disconnection when servicing
controls. Wiring errors can
cause improper and dangerous
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
32
120 Volt AC power is needed for the fan switch
and blower. Athree wire power cord is provided
to be plugged into the receptacle.
Note: A 120 Volt AC power cord can be
installed at rough-in stage so that
the power is available. A three wire
power cord can be used.
To Remove the Fan
1) Shut the power off.
2) Reverse the above instructions.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
5) If the left spring was unhooked in step 3),
hook it back into the bracket. Take care not
toclipanywires.Attachtheadhesivebacked
wire holder clip (Part #910-199) onto the
stove base.
Note: The bearings are lubricated for life.
Do not lubricate them. Make sure
you vacuum the fan area on a regular
basis.
1) Shut the power off.
2) Open the bottom louver door.
3) Slide the fan in towards the rear of the unit
and slip it over the two mounting studs.
Ensure that the fan blades do not rub
against the valve tubing.
Optional: If you require extra space to slide the fan to the back, the left spring can be unhooked
from the bracket.
4) Plug the fan to the receptacle as shown in
the wiring diagram below.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Turn gas control knob so indicator points
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
OPERATING
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
1) Read and understand these instructions
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depressthegascontrolknobfully.Depress
the igniter button several times until the
pilotlights.Afterapproximatelyoneminute,
releasethegascontrolknob.Thepilotflame
should continue to burn. If the pilot does
not remain lit, repeat operation allowing a
longer period before releasing gas control
knob.
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
ADJUSTMENT
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON"
position.
5) Verify that the venting and cap are
unobstructed.
The air shutter can be adjusted by moving the
adjustingwireupordown.Thewireisaccessed
throughthebottomlouveropening.Opentheair
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but
may need adjusting due to either the local gas
supply or altitude.
6) Ensure that the brick panels are installed.
5) Use the wall switch, thermostat or remote
control to turn on the unit.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
6) Rotate the flame height regulator to adjust
the flame height higher or lower.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
Minimum Air Shutter Opening:
3/16"
1/2"
Natural Gas
Propane
PROCEDURE
CAUTION:Carbonwillbeproducedifairshutter
is closed too much.
1) Use the wall switch, thermostat or remote
control to turn off the main burner.
Note: Any damage due to carboning
resulting from improperly setting
theaerationcontrolsisNOTcovered
under warranty.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
Note: Aeration Adjustment should only
be performed by an authorized
Regency® Installer at the time of
installation or service.
service is to be performed.
FIRST FIRE
PROCEDURE
The first fire in your fireplace is part of the
paint curing process. To ensure that the paint
is properly cured, it is recommended that you
burn your fireplace for at least four (4) hours
the first time before you use it with the fan on.
IMPORTANT
To ignite or reignite the pilot,
you must first release the ten-
sion springs below the door.
When first operated, the unit will release
an odour caused by the curing of the paint,
the burning off of any oils remaining from
manufacturing. Smoke detectors in the house
may go off at this time. Open a few windows to
ventilate the room for a couple of hours.
Adjustment Wire: push to close or
pull to open aeration cap.
Only when the pilot holds, without pressure
being applied to the control knob, reapply the
tension springs to the door. The unit must
not be operated with the tension springs
unattached.
Closed - Tall yellow
Open - Short Blue
The glass panel may require cleaning after the
unithascooleddown. DONOTATTEMPT
TO CLEAN THE GLASS WHILE IT
IS HOT.
IMPORTANTGascockknobcannotbeturned
from "PILOT" to "OFF" unless it is partially
depressed.
Note: When the glass is cold and the
appliance is lit, it may cause
condensation and fog the glass.
This condensation is normal and
will disappear in a few minutes as
the glass heats up.
1) Turn burner OFF using "ON/OFF" switch.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
34
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any; if none, follow the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes,
CSA B149.1. (Australia: AG601, New Zealand: NZS 5261)
It is possible that you will hear some sounds
fromyourgasappliance.Thisisperfectlynormal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listedbelowaresomeexamples.Allarenormal
operatingsoundsandshouldnotbeconsidered
as defects in your appliance.
WARNING: If you do not follow these instructions exactly a fire or explosion
may result causing property damage, personal injury or loss of life. Improper
installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Refer to the owner’s information manual provided with
this appliance. For assistance or additional information consult a qualified
installer, service agency or gas supplier
A) This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these
instructions exactly
B) BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor
Burner Tray:
because some gas is heavier than air and will settle on the floor
The burner tray is positioned directly under the
burnertube(s)andlogsandismadeofadifferent
gauge material from the rest of the firebox and
body.Therefore,thevaryingthicknessesofsteel
will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electric switch, do not use any phone in your building.
Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the fire department.
C) Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted
repair may result in a fire or explosion.
D) Do not use this appliance if any part has been under water Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
E) This appliance needs fresh air for safe operation and must be installed so there are provisions for
adequate combustion and ventilation air
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due
to high surface temperatures keep children, clothing and furniture, gasoline and
otherliquidshavingflammablevaporsaway Keepburnerandcontrolcompartment
clean. See installation and operating instructions accompanying appliance.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dullclickingsoundmaybeaudible,thisisnormal
operation of a gas regulator or valve.
LIGHTING INSTRUCTIONS
STOP! Read the safety information above on this label.
Unit Body/Firebox:
FOR UNITS NOT EQUIPPED WITH ELECTRIC SPARK BOXES:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
1) Push in gas control knob slightly and turn clockwise
to “OFF”. Knobcannot be turned from
“PILOT” to “OFF” unless knob is pushed in slightly. Do not force.
PILOT BURNER
VEILLEUSE
OFF
THERMOPILE
Gas Inlet
ELEMENT
THERMO-
ELECTRIQUE
2) Wait five (5) minutes to clear out any gas. If you then smell gas STOP! Follow step “B” in the Safety
Information above on this label. If you don’t smell gas, go to the next step.
MAINTENANCE
3) Turn knob on gas control counterclockwise
to“PILOT”.
4) Push in control knob all the way and hold in. Continually push and release the black button on spark
igniter until pilot lights. Continue to hold the control knob in for about 1/2 minute after the pilot is lit.
Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 1) to 4).
If knob does not pop up when released, stop and immediately call your service technician or gas
supplier If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your
service technician or gas supplier
1) Alwaysturnoffthegasvalvebeforecleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
5) Turn gas control knob counterclock-wise
6) Use rocker switch to operate main burner
to “ON”.
FOR ALL PROPANE UNITS AND UNITS EQUIPPED WITH ELECTRIC SPARK BOXES:
1) Push in gas control knob slightly and turn to “PILOT” position.
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
2) Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control
knob in for about 20 seconds after the pilot is lit. Release knob.
3) Push in gas control knob slightly and turn to "ON" position.
Gas Inlet
4) Turn ON the flame switch.
TO TURN OFF GAS APPLIANCE
3) The heater is finished in a heat resistant
paintandshouldonlyberefinishedwithheat
resistantpaint.UltraGlow® usesStoveBright
Paint - Metallic Black #6309.
1) Turn off the flame switch.
2) Push in the gas control knob slightly and turn clockwise
to “OFF”. Do not force.
3) Turn off all electric power to the appliance if service is to be performed.
You may shut off the pilot during prolonged non use periods to conserve fuel.
918-473
DO NOT REMOVE THIS INSTRUCTION PLATE
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flameoftheburnerperiodically,makingsure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
Your UltraGlow® fireplace is supplied with high
temperature, 5 mm tempered glass that will
withstand the highest heat that your unit will
produce. If your glass requires cleaning, we
recommend using an approved glass cleaner
available at all authorized dealers. Do not use
abrasive materials. Do not clean the glass
when hot.
The 24 carat gold plated or brass finish on the
trim requires little maintenance, and need only
be cleaned with a damp cloth. DO NOT use
abrasivematerialsorchemicalcleaners,asthey
may harm the finish and void the warranty.
5) The appliance and venting system must be
inspected before use, and at least annually,
byaqualifiedfieldserviceperson,toensure
that the flow of combustion and ventilation
air is not obstructed.
Clean any fingerprints off before turning the
unit on. If the top louvers start to discolour,
check the door gasket seal and replace if
necessary.
Intheeventthatyoubreakyourglassbyimpact,
purchase your replacement from an authorized
UltraGlow® dealer only, and follow our step-by-
step instructions for replacement.
Note: Never operate the appliance without
the glass properly secured in
place.
6) Donotusethisapplianceifanyparthasbeen
under water. Immediately call a qualified
service technician to inspect the appliance
andtoreplaceanypartofthecontrolsystem
and any gas control which has been under
water.
WARNING:Donotoperatetheappliance
withtheglasspanelsremoved,cracked
or broken. Replacement of the glass
panels should be done by a licensed
or qualified service person.
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
7) Verify operation after servicing.
Caution: Wear gloves when removing
damaged or broken glass.
General Vent Maintenance
Flush Glass Replacement
Conduct an inspection of the venting system
semi-annually.Recommendedareastoinspect
as follows:
Note: Improperpositioningoflogsmaycreate
carbonbuild-upandwillseverelyalter
the unit's performance which is not
covered under warranty.
Removetheflushdoorfront(asperinstructions
in the "Standard Flush Door" section). Remove
the 4 glass clips from each corner. Slide in the
new replacement glass. Push the 4 glass clips
back onto the frame. The glass must have
gasketing around it.
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or
streaks, and in extreme cases, holes.
These components should be replaced
immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
1) Open the bottom louvers.
2) Loosenthethermocoupleorthermopilewith
3) Check for evidences of excessive
condensation,suchaswaterdropletsforming
intheinnerliner, andsubsequentlydripping
outthejoints,Continuouscondensationcan
cause corrosion of caps, pipe, and fittings.
It may be caused by having excessive
lateral runs, too many elbows, and exterior
portions of the system being exposed to
cold weather.
a 7/16" wrench.
3) Disconnect thermocouple by loosening
nut from the valve with a 9mm wrench.
Disconnectthermopilebyloosening2screws
marked TP on the valve.
4) Drop the thermocouple or thermopile down
from the bracket and pull it out of the unit.
4) Inspect joints, to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
5) Reinstall the new ones in reverse order.
If the glass gasket requires replacement use
a tadpole glass gasket for the Flush Front (Part
# 936-155).
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
36
11) Removethe12Phillipsheadscrewssecuring
1) Shut off the gas supply.
2) Remove louvers.
the valve tray assembly in place.
1) Attach the valve to the valve bracket with
the 4 (m5x8 metric) screws provided.
2) Reconnect the "gas out" flare fitting with an
3) Open and remove the flush door.
4) Remove logs.
11/16" wrench.
3) Reconnect the "gas out" flare nut with a
13/16" wrench.
5) Remove the burner assembly by removing
the two Phillips head screws.
4) Install piezo ignitor push button assembly
and reconnect wire.
Valve Tray Assembly
screws
5) Reconnectthequickdropoutthermocouple
nut with a 9mm wrench.
12) Lift the entire assembly out.
6) Reconnect the pilot tube nut with a 7/16"
wrench.
7) Scrapeofftheoldgasketfromthefloorofthe
firebox and from the valve tray assembly.
6) Remove the burner assembly by sliding left
8) Install a new gasket and reinstall the valve
and out.
tray assembly.
Note: Failure to install a new gasket
may severely affect the appliance
performance.
9) Reinstall the 12 hold down screws.
10) Hook up the 2 TP and 2 TH wires to the
appropriate connections on the valve.
7) Remove the rear log stand by removing the
11) Reinstall the bottom brick panel and the
2 screws.
front log stand.
Rear Log Stand
Screws
12) Install burner assembly
13) Hook up the gas line and check for gas
leaks with a soap and water solution or a
gas leak detector. (Do not use open flame
for leak testing.)
13) Undo the pilot tube from the valve with a
7/16" wrench.
14) Undo the quick drop out thermocouple nut
on the valve with a 9mm (metric) wrench.
14) Fire up the unit temporarily
15) Remove the Piezo ignitor wire and push
15) Check the manifold pressure.
button assembly.
16) Reinstall the logs and base panels as
16) Undo the "gas out" flare nut with a 13/16"
needed.
8) Lift out the bottom base panel.
wrench.
17) Close the door and replace the louvers.
17) Undo the "gas out" flare fitting with an 11/16"
wrench.
18) Fire up the unit again and check for proper
flame appearance and glow on logs.
18) Remove the 4 Phillips head screws from
the sides of the valve bracket and remove
valve.
Hint:
If you are using black pipe, ensure
that there is a union by the valve,
otherwise removal will be almost
impossible.
9) Disconnect the inlet gas line.
10) Disconnect the 2 TP wires and the 2 TH
wires from the valve.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Part #
Description
Part #
Description
27)
28)
29)
30)
34)
35)
*
*
*
*
*
*
Outer Flue Collar
Inner Flue Collar Assy
Flue Mounting Plate
Gasket for Flue Collar
Firebox Tray
1) 948-253 Door Handle
2) 510-026 Hinge Bracket - Left/Right
3) 948-045 Chain
4) 948-115 Spring
Thermodisc Bracket
910-882 Wire-Harness-Valve to Burner
6) 430-129 Receptacle Box Mount
7) 910-429 Box - Receptacle
8) 910-428 Duplex Receptacle
9) 910-430 Cover - Receptacle
10) 904-687 Clamp Connector
331-917 Fan & Speed Control Assy
(120 Volts) Optional
42) 910-331/P Fan Motor
20) 510-033 Top Nailing Strip
21) 510-064 Side Nailing Strip
50) 510-994 Optional Rigid Pipe Adaptor
101) 690-022 Cover Plate - Outer Box Side
23) 780-011 Standoff - Top
918-515 Manual
24) 780-013 Standoff - Side/Back
290-969 Conversion Kit - NG to LP
*Not available as a replacement part.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
38
G36D BURNER ASSEMBLY & LOG SET
Part #
Description
52) 910-190
Piezo Ignitor & Nut
53) 780-021
786-574/P
786-576/P
Gasket - Valve Access Plate NG/LP
Valve Assy - Natural Gas
Valve Assy - Propane
56) *
Valve Tray - NG/LP
57) 910-378
910-380
58) *
Valve - S.I.T. - Natural Gas
Valve - S.I.T. - Propane
Valve Bracket
65) *
Pilot Bracket
66) 910-038
910-039
Pilot Assy - S.I.T. - 3 Flame NG
Pilot Assy - S.I.T. - 3 Flame LP
Pilot Holder
67)
*
68) W840470
904-430
Pilot Assembly Gasket
Orifice #42 - Natural Gas
Orifice #53 - Propane
Orifice Gasket
904-345
936-170
69) *
Firebox Base
75) *
76) *
Deflector - Left
Deflector - Right
79) 786-525
Burner Assy - NG/LP
83) *
85) 780-930
Rear Log Support Bracket
Log Set
86) * Pilot Deflector
*Not available as a replacement part.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
39
Download from Www.Somanuals.com. All Manuals Search And Download.
G36D FLUSH FRONT ASSEMBLY
Part #
Description
131) 510-934 Flush Glass Trim (Set) - Brass
510-947 Flush Glass Trim (Set) - Steel
510-932 Flush Glass Trim (Set) - Gold
132) 904-196 Magnet (1" Round)
133) 780-069 Flush Louver - Top - Black
134) 786-520 Assembly - Bottom - Black
135) 940-334/P Glass - Tempered
137) 904-691 U-Clip
139) 936-155 Glass Gasket (Tadpole)
140) 948-042 Spring Hinge - Black
*Not available as a replacement part.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
40
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
41
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
42
® products, are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully
inspects each unit thoroughly before it leaves our door. UltraGlow® is pleased to extend this one year warranty to the original purchaser
® product. This warranty is not transferable.
The Warranty: One Year
Covered under the agreement are the following components: Combustion chamber, heat exchanger, burner tubes, logs, embers, glass (thermal
breakage) and all gold plating (against defective manufacture).
The above will be covered for parts and labour for one year. Electrical components such as blowers, fan motor, switches, wiring, thermodiscs,
remote control, thermopiles, thermocouples, pilot assemblies, and gas valves are covered for one year from the date of purchase.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited
distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned
to FPI and evaluated for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your FPI product. FPI will not be liable for results or costs of
workmanship from unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information
including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be
invalid.
Exclusions:
This Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify
any unit once manufactured. ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this
warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse,
improper installation, negligence or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation,
excessive offsets, negative air pressure caused by mechanical systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from
FPI, may nullify your warranty on this product.
Simpson Dura-Vent venting components are covered by Simpson Dura-Vent Inc. warranty.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
UltraGlow® G36D Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
43
®
Installer: Please complete the following information
Dealer Name & Address:
Installer:
Phone #:
Date Installed:
Serial No.:
© Copyright 2005, FPI Fireplace Products International Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
QSC Audio Stereo Amplifier DCA 1222 User Guide
Rangemaster Oven U109720 01 User Guide
Reebok Fitness Home Gym RBCCEL79020 User Guide
Renesas Network Card M16C 6N User Guide
Ricoh Scanner IS100e User Guide
Rosle Cookware 95030 User Guide
Rover Lawn Mower 11029S User Guide
Samson DJ Equipment XP308i User Guide
Samsung Clothes Dryer DV438AE User Guide
Sears Fitness Equipment 831280781 User Guide