TM
O w n e r ’ s M a n u a l
Download from Www.Somanuals.com. All Manuals Search And Download.
time of sale were selected on the basis of their compatibility with the
frame, fork and all other parts. Certain after-market products may or
may not be compatible with your Razor Electric Scream Machine.
Consult your retailer or call Razor prior to modifying or replacing any
component with a non-factory specified product.
TOOLS REQUIRED FOR ASSEMBLY ONLY
Razor recommends assembly by an adult with
experience in bicycle mechanics. Some tools
may be supplied, however we recommend the
use of mechanic’s grade tools and use the
supplied tools only as a last resort.
4, 5 and 6 mm hex (Allen) keys
17mm open end wrench
Bicycle-style pump (to inflate the tire)
1. Parts of the Electric Scream Machine
J
I
H
E
F
G
Q
K
N
D
M
P
L
C
A
B
O
A. Front wheel
B. Pedal
I. Handlebar grip
J. Handlebar
Q. Motor cover
C. Crank arm
K. Headset
D. Wheel cover
E. Fork
F. Brake
G. Fork crown
H. Brake lever
L. Head tube
M. Main frame
N. Seat/battery pack
O. Rear wheels
P. Rear axle
Additional components not
shown in this view will be
detailed in the assembly
section.
NOTE: For safety reasons, the Electric Scream Machine must be
moving at least 3mph before the motor will start. Pedal or push to
3mph, then pull the trigger to start the motor!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Proper Fit and Size Adjustments
2. Fit. When properly adjusted, the rider should be able to pedal
comfortably and steer with both feet remaining on the pedals at all
times. If the rider has to stretch to reach the pedals or is too cramped,
the seat should be adjusted fore or aft accordingly.
WARNING: The age recommendation is only an estimate. If you
are too small or too large to comfortably reach the pedals or
handlebars, do not ride the Electric Scream Machine.
WARNING: Failing to properly adjust and tighten the screws, bolts
and clamps that affix the handlebars, seat and rear wheels can cause
you to lose control and fall. When properly tightened, you cannot twist
the front wheel out of line with the handlebars or move the saddle out of
adjustment. If you can twist or force these components to move or
come off by hand, readjust and properly retighten the screws and bolts.
3. Brake
Your Razor Electric Scream Machine is fitted with a hand-operated
brake. The brake lever may be positioned on the handlebar where it is
most comfortable for the rider. To change the position, loosen the
clamping screw and slide the brake lever to the new position and
retighten securely.
Figure 1. Brake lever adjustment.
WARNING: The brake, when properly adjusted, is capable of
skidding the tire and throwing an unsuspecting rider. Practice in an
open area free from obstacles until you are familiar with the brake
function.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Cable operated brakes are very effective but must be
adjusted and maintained on a regular basis. Check or have them
checked and adjusted by a qualified mechanic. Worn brake parts,
stretched or frayed inner wires or a kinked housing indicate brake
service or parts replacement may be necessary for proper function.
4. Safety
4A. Helmets. Although not every state or municipality requires the user
to wear a helmet, Razor strongly recommends you wear a properly
approved helmet, such as ANSI or SNELL, even if the law does not
mandate the use of a helmet.
Suitable helmets are available in a variety of styles. The most popular
for kids is the skateboard-style “stunt” helmet. There are many brands
available and they come in various sizes to fit any child or adult.
WARNING: Helmets must be properly fitted and the straps
adjusted properly to be effective. Ask your dealer to help you with the
selection, fit and adjustment of your helmet.
4B. Night riding and low-light conditions. Razor strongly
recommends against riding at night or when lighting or visibility
conditions are less than optimal (such as dawn and dusk).
WARNING: Lighting for night riding or low light conditions are not
required and are not standard equipment on the Electric Scream
Machine. We do not recommend riding at night or in low-light
conditions.
4C. Bare feet. Do not ride with bare feet. Wear enclosed shoes when
riding.
Keep feet on the pedals at all times while riding in the seated position.
Do not ride more than one person at a time. Never use near steps or
swimming pools.
4D. Wet weather riding. Do not ride in wet conditions.
WARNING: Wet weather impairs traction, braking, control and
visibility. The risk of accident is increased dramatically in wet weather.
WARNING: Keep your fingers and other body parts away from the
crank, steering system, wheels, motor, belt and all other moving
5
Download from Www.Somanuals.com. All Manuals Search And Download.
components. Riders with longer hair may risk entanglement in the rear
wheels or drive system. Do not allow long hair to get near the wheels or
drive system.
5. Safety Check (before each ride)
5A. Loose parts. While straddling the Electric Scream Machine, lift the
front wheel off the ground two or three inches and let go so it can
bounce on the ground. Does everything sound tight? There should not
be any unusual rattles or sounds from loose parts or broken
components. If you are not sure, ask an experienced mechanic to
check.
5B. Brake. Check the brake for proper function. When you pull the lever
the brake should act against the rim and provide positive braking action.
The cable should have the proper slack so the brakes do not drag, yet
the lever should not touch the handlebars when pulled except under the
hardest braking action.
5C. Frame, fork and handlebars. Check for cracks or broken
connections. Although broken frames are unlikely and rare, it is possible
for an aggressive rider to bash into a curb or wall and wreck and bend
or break a frame, fork or handlebar. Get in the habit of inspecting yours
regularly.
5D. Bar ends. Your Razor is equipped with plugs in the end of the
handlebars designed to provide protection from exposed handlebar
ends, which can act like a cookie-cutter. If your bar plugs are worn out
or missing and the handlebar end is exposed, replace them or cover the
exposed end(s) with after-market bar-end protectors.
5F. Tire inflation. The front tire on the Electric Scream Machine
requires 35~45 psi inflation pressure. Periodically and regularly check
the tire pressure and reinflate as necessary. If you get a flat tire the
inner tube is available at any retailer that sells bicycle parts and
accessories. The correct size is embossed on the side of the tire (16 x
1.75).
NOTE: For safety reasons, the Electric Scream Machine must be
moving at least 3mph before the motor will start. Pedal or push to
3mph, then pull the trigger to start the motor!
6. Assembly
NOTE: The color of the product in certain photos may appear to
6
Download from Www.Somanuals.com. All Manuals Search And Download.
be different than the color of the product you purchased. The colors
were altered to make the assembly photos easier to follow.
WARNING: Razor highly recommends that you have your Electric
Scream Machine assembled by an experienced, adult mechanic. Many
retailers provide assembly but some charge extra. If your retailer can’t
do the assembly, you can have your Electric Scream Machine
assembled at a bicycle shop for a fee. Although you may have to pay
up to $30 or even more for assembly, it will assure the Electric Scream
Machine is properly put together and adjusted.
ASSEMBLY NOTE: Refer to the list of tools required for assembly
on page three of this manual. If you do not have the proper tools or
understanding of the instructions in this manual, take your bike to a
qualified mechanic for assembly, service or adjustments.
6A. Unbox. Remove contents from box. Remove the foam, bubble-
wrap, cardboard and/or plastic separators that protect the various
components from damage during shipping. Inspect the contents of the
box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Your Electric Scream Machine was partially
assembled and packed at the factory to prevent shipping damage and
there should not be any problems, even if the box has a few scars or
dents. But if there are, contact Razor at 866-467-2967 to resolve any of
these issues.
6B. Install the fork.
Insert the steering tube into the frame as shown in 2a and 2b. The
steering bushings are preinstalled.
Figure 2a.
Figure 2b.
Carefully unwind the handlebar/upper crown assembly so the wires are
7
Download from Www.Somanuals.com. All Manuals Search And Download.
not tangled or twisted and so the brake cable and trigger wire are
routed as shown in 2c.
Insert the handlebar and upper fork crown assembly into the fork legs
as shown in Figure 2d. Press both the spring buttons (arrows, 2d)
and continue to slide the handlebar assembly into the fork until the
spring buttons engage the holes (A) as shown in Figure 2e, and the
steering tube extends through the upper fork crown (B). The fork stop
must be positioned in the slot in the upper crown. The fit between the
tubes is a close tolerance and may require a firm hand or taps with a
rubber mallet to nudge the handlebar all the way into the fork.
Figure 2c.
Figure 2d.
Figure 2e.
Install the tensioning cap and adjusting screw as shown in Figure 2f.
Using an Allen key, snug the adjusting screw as shown in Figure 2g
until the fork crown is firmly seated against the steering bushings. This
is called “preloading.”
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2f.
Figure 2g.
Once the fork crown is firmly seated, loosen the adjusting screw
approximately 1/4 to 1/2 turn. This relaxes the preloading and allows the
steering to rotate without binding. Test by turning the handlebars to full
lock left and right. It should steer with slight friction and no binding or
tight spots.
NOTE: The steering bushings are designed for long life and
should require no maintenance. They do not require oil or any type of
“wet” lubrication. If the steering becomes rough, disassemble, inspect
and clean the bearing surfaces (soap and water is fine). Dry thoroughly
and reassemble. Although the bushings and thrust washers are self-
lubricating, a light application of a dry-lube can be used to facilitate the
anti-friction properties of the steering head bushings.
WARNING: Failure to properly install the handlebar to the fork
legs can result in the handlebars falling off and causing risk of injury.
Periodically check to make certain the adjusting screw is properly
tensioned and that the handlebars are securely attached to the forks.
Refer to the safety information in chapter 5 for additional details.
6C. Install the rear wheels. Flip the Electric Scream Machine upside
down. Locate both rear wheels and examine the protruding axle
threads. Notice there are two styles of wheels:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3a. The wheel on the right is the wheel with the power coupler.
Notice the blue residue on the axle threads. This is a non-hardening
thread-locking “glue” designed to prevent the axle from vibrating loose.
You will install the wheel with the power coupler on to the drive-side of
the Electric Scream Machine. The coupler is shown in Figure 3b.
Figure 3b. The power coupler.
Using a 6mm Allen key, thread the axle into the frame and tighten until
the power coupling is about to engage with the mating part of the wheel
(Figure 3c).
Figure 3c.
Figure 3d.
Make sure the coupling is full engaged
as shown.
Align the power coupling
and tighten until the axle is tight
against the frame.
Carefully align the coupling as shown and, while holding the wheel to
maintain this alignment, tighten completely and firmly until the axle is
tight against the frame and so the coupling is completely engaged as
shown in Figure 3d.
Flip the Electric Scream Machine right-side up to prepare to install the
10
Download from Www.Somanuals.com. All Manuals Search And Download.
left-side (non-drive) wheel.
NOTE: The left side (non-drive) axle and locking nuts have
backwards threading. This axle is special and is not compatible with
the drive-side of the Electric Scream Machine. This axle is also not
compatible with previous versions of the Scream Machine.
Using a 6mm Allen key, carefully thread the axle into the frame by
turning counter clockwise as shown in Figure 3e.
Figure 3e. Tightening the backwards threaded axle.
When the locking nuts come in contact with the frame, check the wheel
to see if it spins freely or if there is excess side-to-side play. If it spins
free and there is just a slight end play, tighten the axle securely and,
using the 17mm wrench, tighten both locknuts against the frame. If the
wheel will not spin freely, loosen the locknuts and unthread the axle
about 1/4 turn and adjust the locking nuts in or out as shown in figure 3f
until the wheel spins free with little or no side play. The correct
adjustment is where the wheel spins free, has the least amount of end-
play as possible, and both lock nuts are tightened securely against the
frame.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3f.
Tightening the locknuts against the frame as shown in figure 3f.
Repeat the adjustment procedure in 6C as many time as necessary
to obtain the proper adjustment.
other procedures.
NOTE: Although we make every effort to keep our manual up-to-
date, if your Electric Scream Machine does not look like this, then we’ve
made product improvements since this document was printed. Check
latest service and adjustment procedures.
6D. Connect the motor.
The motor must be connected to the battery pack prior to installing the
seat. To connect, push the 4-pin coupling into the socket in the corner of
the battery pack as shown in Figures 4a and 4b
Figure 4a.
Figure 4b.
6E. Attach the seat.
Flip the Electric Scream Machine on it’s side and, using the screws
shown in Figure 5a and the 4mm Allen key, fasten the seat to the frame
as shown in Figure 5b using one of the two positions: forward or aft,
depending on the rider’s size.
NOTE: The screws visible from the top of the seat attach the
mounting bracket to the plastic seat. Do not remove these screws.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5a.
Figure 5b.
6F. Install cranks and pedals. The crankarms, pedals and hardware
are supplied in the parts bag and must be installed. The crank marked
L goes on the left side and the crank marked R goes on the right
side (when sitting in the seat).
Figure 6a.
Assemble as shown in the sequence below. Tighten securely.
Figure 6b.
Figure 6c.
Figure 6d.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6F. Charging prior to use. The Electric Scream Machine will probably
not have a fully charged battery pack at the time of purchase. Therefore
it is a good idea to charge the battery prior to use. The charging input is
located at the back of the motor cover next to the switch. The charger
has two small LEDs that illuminate to indicate the charge status. Red
indicates the charger is working and green indicates the battery is fully
charged. The initial charge could take from a few minutes to up to 6
hours, depending on the battery state.
Figure 7a.
6G. Main switch with auto reset. The Electric Scream Machine has a
circuit breaker that will automatically shut off the power to the motor in
the event an overload condition is placed on the motor. An excessive
overload, such as too heavy a rider or too steep a hill, could cause the
motor to overheat. If your Electric Scream Machine abruptly stops
running and it is fully charged, wait a few seconds and then toggle the
switch to reset the breaker. Avoid whatever conditions caused the
breaker to trip and avoid repeatedly tripping the breaker.
NOTE: For safety reasons, the Electric Scream Machine must be
moving at least 3mph before the motor will start. Pedal or push to
3mph, then pull the trigger to start the motor!
7. Maintenance
7A. Tire inflation. The front tire on the Electric Scream Machine
requires 35~45 psi inflation pressure. Periodically and regularly check
the tire pressure and reinflate as necessary. If you get a flat tire the
inner tube is available at any retailer that sells bicycle parts and
accessories. The correct size is embossed on the side of the tire (16 x
1.75).
7B. Brake cable adjustment. The main adjustment on the brake is to
take up the cable slack and bring the lever into adjustment. This is
typically accomplished with the adjusting barrel at the brake lever as
shown in Figure 8a
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8a.
If there is too much slack, the lever will go all the way to the handlebar
without the brake being applied. If there is not enough slack, the brake
will drag even when the lever is not pulled. Ideally, you want 2-3mm of
play in the lever before the brake engages (as shown in figure 8b).
Figure 8b.
To adjust, loosen the lock ring and turn the barrel 1/4 to 1/2 turn to
loose or tighten as required and squeeze the brakes to test. Continue to
adjust until the proper cable slack is attained.
If the proper amount of play cannot be achieved by adjusting the brake
lever, the excess slack must be taken up at the brake by loosening the
pinch bolt as shown in Figure 8c and pulling up the excess cable slack.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8c.
NOTE: The brake system requires a break-in period. You may
have to repeat procedure 6F often during the first several hours of use.
Repeat as necessary thereafter to maintain proper brake function.
The Electric Scream Machine is supplied with a brake lever that adjusts
to accommodate a variety of hand sizes. To adjust the brake lever so it
is easier for shorter hands to operate the brake, turn the screw in the
direction marked “B” in the photo below. Leave enough gap between
the handlebar and lever to assure proper brake function. To readjust for
larger hands, turn the screw in the direction marked “A” as shown in
Figure 13a below.
Figure 13a.
WARNING: Always test the brake function whenever making any
adjustment to the braking system.
WARNING: Brake pads are subject to normal wear and tear.
Although the brake pad alignment is pre-adjusted at the factory and
should not require additional adjustment at the time of assembly, it is
16
Download from Www.Somanuals.com. All Manuals Search And Download.
the responsibility of the user to periodically inspect the brake pads for
excess wear and misalignment. If you do not understand how to adjust
or realign the brake pads, we strongly recommend you seek the help of
a qualified mechanic. If the brakes are not properly adjusted the brakes
may fail and you can be seriously injured.
8. Razor Safety Tips
WARNING TO PARENTS: Kids need to be taught and be
frequently reinforced of the importance of safe riding, the rules of the
road and the dangers and hazards of traffic, especially motor vehicle
traffic. Parents and children are urged to read and understand these
safety tips together.
8A. Rules of the road
Do not play in the road or street.
Do not ride on streets.
Do not ride at night.
Stop for all stop signs.
Use crosswalks to cross streets.
Always walk at crosswalks.
Never use near steps or swimming pools.
8B. Your driveway. Driveway accidents are frequent and often fatal.
Realize the danger of your own and all other driveways. There may be
obscured vision caused by trees, bushes or cars. Your driveway is not a
launching pad for fast roll-outs! Observe the following driveway safety
tips:
Look left, right and left again before exiting onto sidewalks or into
playground areas.
8C. Stop signs. Running a stop sign is a sure way to get hit by a car
and killed. Remember, always stop at every stop sign or stop light.
Always stop and walk across only when it is clear. Do not assume that
drivers of motor vehicles can see you. In fact, assume that every driver
cannot see you and that they are not paying attention. Observe the
following safety tips:
Stop at all stop signs and lights, regardless of traffic conditions.
Look in every direction of traffic before proceeding to walk across.
Watch especially for oncoming traffic making left turns.
Watch for cars behind you or next to you making right turns.
Wait for traffic to clear before proceeding.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8D. Turning without warning. Children are often struck from behind
because they made unexpected turns into traffic, or they inadvertently
veered into traffic when looking over their shoulder. Observe the
following safety tips for left turns:
Do not cut across the street, cross only at intersections.
Practice looking over your shoulder to the rear without accidentally
turning (do this only in an open space free from traffic and
obstructions).
8E. Riding at night and in low visibility. Do not ride at night or in low
visibility. See section 4 for more information.
8F. Rules of the Road.
Wear a helmet. Wear shoes.
Learn local bicycle laws and regulations. Most states and
communities have rules regarding helmet use, bicycle licensing,
riding on sidewalks, grinding and so on. It is the responsibility of
parents to make sure their children know and obey all rules and
regulations.
The Electric Scream Machine is intended for sidewalk and
playground use. You must share this space with others including,
pedestrians, skaters and other players. Respect their rights!
Ride defensive. Assume that pedestrians, skaters and other players
are so absorbed in their own world that they are not paying any
attention to you and that they will run you down or step out in front
of you, all without any warning.
Watch for obstacles such as pot holes, sewer grates, expansion
cracks, and road or construction debris (such as nails or other
foreign objects) that could catch your wheel or force you to swerve
into traffic or lose control.
Stop at all stop signs and lights.
Never ride with headphones or use a cell phone when riding.
Never carry a passenger.
Never hitch a ride with another vehicle.
Do not weave into traffic or make sudden turns.
Observe and yield the right-of-way as prescribed by local traffic
rules.
Riding the Electric Scream Machine may be a hazardous activity and
has inherent dangers that no amount of care, caution, instruction or
expertise can eliminate. Certain conditions may cause the equipment to
18
Download from Www.Somanuals.com. All Manuals Search And Download.
fail without fault of the manufacturer. Activities involving the use of
bicycles carry the risk of injury or death.
9. Razor Limited Warranty and Registration
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited
Warranty does not cover normal wear and tear, tires, tubes or cable, nor
any damage, failure or loss caused by improper assembly,
maintenance, storage or use of the Electric Scream Machine.
This Limited Warranty will be void if the product is ever:
used in a manner other than for recreation or transportation;
modified in any way;
rented.
Check local laws and regulations to see where you can ride your
Electric Scream Machine legally.
The manufacturer is not liable for incidental or consequential loss nor
damage due directly or indirectly from the use of this product.
To obtain service under this warranty you must, within the
warranty period, contact Razor USA LLC directly by e-mail at
[email protected]. Razor will provide warranty replacement
at its sole discretion.
Authorized warranty service is ONLY available from Razor USA
LLC.
IMPORTANT!
If your Electric Scream Machine has a problem
call Razor USA Toll Free (866) 467-2967
DO NOT RETURN TO STORE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
QUESTIONS?
Please read the owner’s manual thoroughly. If you still have
questions, check the website for updates and contact information.
Spare rear wheels are available! Keep your Electric Scream
Machine running for years with these and other genuine Razor
spare parts.
Visit our website and e-mail us for more information
on spare part availability.
Specifications subject to change without notice.
Patent Pending
ESM Rev. 5/12/03 ©Copyright 2003, Razor USA.
Cerritos, CA
All rights reserved.
Photos by Arthur Cambridge
Download from Www.Somanuals.com. All Manuals Search And Download.
|