|
A60 and RS12
Display & GPS
Installation Manual
Document number: 87081-1
Date: December 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Contents
Trademarks and registered trademarks ............................................ 2
Important Information .........................................................................................5
Suppression Ferrites.......................................................................... 7
Connections to Other Equipment ..................................................... 8
Chapter 1: Introduction .......................................................................................9
1.1 Selecting the Display Unit Location ........................................................ 9
1.2 What Comes in the Box ........................................................................ 10
1.3 Optional Equipment ............................................................................. 11
1.4 Unit Size ............................................................................................... 12
Chapter 2: Installing the Display Unit ..............................................................13
2.1 Mounting ............................................................................................. 13
Mounting Bracket Method.................................................................... 13
Flush Mounting..................................................................................... 14
2.2 Cable Runs............................................................................................ 15
Making the Cable Connections............................................................. 16
Power Input Cable (R08003)................................................................. 16
Power Supply.................................................................................. 17
NMEA Cable (R08004).......................................................................... 18
GPS Cable ............................................................................................ 18
Chapter 3: Installing the GPS Antenna.............................................................19
3.1 Selecting the Mounting Location ......................................................... 19
Receiver Location ................................................................................. 19
Cabling Route ...................................................................................... 20
3.2 Mounting the Receiver ......................................................................... 20
Pole Mounting ...................................................................................... 20
Surface Mounting ................................................................................ 21
Making the Cable Connections ............................................................ 22
Chapter 4: Maintenance ....................................................................................23
4.1 Introduction ......................................................................................... 23
Servicing and Safety.............................................................................. 23
Routine Checks .................................................................................... 23
Cleaning the Display Window .............................................................. 24
Recommended Cleaning Procedure ............................................... 24
4.2 Resetting the System ............................................................................ 24
Power-on Reset .............................................................................. 24
Settings Reset ................................................................................ 25
Settings and Data Reset ................................................................. 25
4.3 Troubleshooting ................................................................................... 25
Common Problems and How to Solve Them ......................................... 26
Download from Www.Somanuals.com. All Manuals Search And Download.
4
A60 Installation Manual
4.4 Upgrading the Display...........................................................................27
4.5 Technical Support .................................................................................29
Worldwide Web ....................................................................................29
Help us to help you ...............................................................................29
Contacting Raymarine in the US ...........................................................30
Contacting Raymarine in Europe ..........................................................31
Appendix: Specifications................................................................................33
A60 LCD Color Display ..........................................................................33
General ..........................................................................................33
Chartplotter Features .....................................................................34
Interfacing ......................................................................................35
RS12 GPS Antenna ...............................................................................36
Index ......................................................................................................................37
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Important Information
Intended Use
The A60 is a GPS Chartplotter display unit that can be upgraded to include
optional Fishfinder functionality.
This handbook contains important information on the installation of your A60
display and RS12 GPS Antenna. To get the best results in operation and
performance, please take the time tothoroughly read the accompanying Owner’s
Handbook.
Safety Notices
WARNING: Navigation Aid
This product is intended to be used as an aid to navigation. Its
accuracy can be affected by many factors, including equipment
failure or defect, environmental conditions and incorrect
handling or use. It is the user’s responsibility to exercise common
prudence and navigational judgement. This device should not be
relied upon as a substitute for such prudence and judgement.
WARNING: Product Installation
This equipment must be installed in accordance with the
instructions in this manual. Failure to do so could result in poor
product performance, personal injury and/or damage to the
vessel.
WARNING: Electrical Safety
Make sure the power supply is switched off before making any
electrical connections.
CAUTION: Global Positioning System Antenna
Do not connect or disconnect the GPS antenna from the display
unit while power is switched on as this may result in irreparable
damage.
CAUTION: Water Ingress
To prevent the ingress of water and consequent damage to the
display, ensure that the chart card door is firmly closed. This can
be confirmed by an audible click.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
A60 Installation Manual
CAUTION: CompactFlash Card Installation
When installing CompactFlash cards ensure that the card is
inserted in the correct orientation. DO NOT try to force the card
into position as this may result in irreparable damage to the card.
CAUTION: CompactFlash Card Damage
DO NOT use a metallic instrument such as a screwdriver or pliers
to help you remove a card, as this can cause irreparable damage.
TFT LCD Displays
The colors of the display may seem to vary when viewed against a colored
background or in colored light. This is a perfectly normal effect that will be seen
with all color LCD displays.
In common with all Thin Film Transistor (TFT) LCD displays, the screen may exhibit
afew (less than5)wrongly illuminated pixels. These may appearas black pixelsin
a light portion of the screen or as colored pixels in black areas.
CAUTION: To provide protection against the damaging effects of
UV light, Raymarine advises that you replace the sun cover
provided when the color LCD display is not in use.
Protective Dust Covers
Protective covers have been attached on the SONAR, AUX and NMEA connectors
on the rear of the A60. If you are not using one or more of these ports, please keep
the cover attached to the connector to protect it from the elements.
Dust Cover
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
7
EMC Conformance
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
Their design and manufacture conforms to the appropriate Electromagnetic
Compatibility (EMC) standards, but correct installation is required to ensure that
performance is not compromised. Although every effort has been taken to ensure
that they will perform under all conditions, it is important to understand what
factors could affect the operation of the product.
Theguidelinesgivenheredescribethe conditionsforoptimumEMCperformance,
but it is recognized that it may not be possible to meet all of these conditions in all
situations. ToensurethebestpossibleconditionsforEMCperformancewithinthe
constraints imposed by any location, always ensure the maximum separation
possible between different items of electrical equipment.
For optimum EMC performance, it is recommended that wherever possible
Raymarine equipment and cables connected to it are:
At least 3 ft. (1 m) from any equipment transmitting or cables carrying radio
signals e.g. VHF radios, cables and antennas. In the case of SSB radios, the
distance should be increased to 7 ft. (2 m).
More than 7 ft. (2 m) from the path of a radar beam. A radar beam can nor-
mally be assumed to spread 20 degrees above and below the radiating ele-
ment.
Ensure that the equipment is supplied from a separate battery from that used for
engine start. Voltage drops below 10 V, and starter motor transients, can cause
the equipment to reset. This will not damage the equipment, but may cause the
loss of some information and may change the operating mode.
Ensure that Raymarine specified cables are used. Cutting and rejoining these
cablescancompromiseEMCperformanceandmustbeavoidedunless doingsois
detailed in the installation manual.
Suppression Ferrites
If a suppression ferrite is attached to a cable, this ferrite should not be removed. If
the ferrite needs to be removed during installation it must be reassembled in the
same position. If a ferrite is packed separately in the carton, it must be installed as
soon as the cables are run.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
A60 Installation Manual
The following illustration shows typical cable suppression ferrites sometimes
used with Raymarine equipment. To ensure EMC compliance, always use these
ferrites, if supplied by Raymarine for use with this equipment. If not supplied by
Raymarine, a ferrite is not required for use with this equipment.
Connections to Other Equipment
If your Raymarine equipment is to be connected to other equipment using a cable
not supplied by Raymarine, the suppression ferrite (if supplied) MUST always be
attached to the cable nearest the Raymarine unit.
Declaration of Conformity
RaymarineplcdeclarethattheA60DualFunctionDisplaysareincompliancewith
the essential requirements of EMC directive 2004/108/EC. The original
Declaration of Conformity certificate can be viewed on the relevant product page
Product Disposal
Waste Electrical and Electronic Equipment (WEEE) Directive
The WEEE Directive requires the recycling of waste electrical and electronic
equipment. While the WEEE Directive does not apply to some of Raymarine’s
products, we support its requirements as part of our environmental policy and we
ask you to be aware of how you should dispose of this product.
The wheelie bin symbol found on our products signifies that it should not be
disposed of in general waste or landfill. Please contact your local dealer, national
distributor or Raymarine Technical Services for information on product disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Chapter 1: Introduction
This manual provides information and instructions for installing your A60 display
and RS12 GPS sensor.
1.1 Selecting the Display Unit Location
Your A60 can be mounted using the mounting bracket supplied, or console
mounted using the optional flush mount kit.
Before you install the display, plan its installation, considering:
•
•
•
Convenience. The mounting location should be easily accessible to allow
operation of the front panel controls.
Access. There must be sufficient space behind the display to allow cable con-
nections to the rear panel connectors, avoiding tight bends in the cable.
Interference. Theselectedlocationshouldbefarenoughawayfromdevices
that may cause interference, such as motors, generators and radio transmit-
ters/receivers (see EMC Guidelines).
•
•
•
Magnetic compass. Mount the display at least 3ft (1m) away from a mag-
netic compass.
Cable runs. The display should be mounted as close as possible to the DC
power source.
Environmental. Thedisplayshouldbeprotectedfromphysicaldamageand
excessivevibration.Althoughthedisplayunitiswaterproof,itisgoodpractice
to mount it in a protected area away from prolonged and direct exposure to
rain and salt spray.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
A60 Installation Manual
1.2 What Comes in the Box
Unpack the display carefully, to prevent damage. Save the carton and packing, in
case the unit has to be returned for service.
Power/Data Cable, 3 pin, 1.5m
Frame Screws,
M3 (x4)
part no. R08003
Mount Frame,
part no. R38109
A60 Dual Function Display,
E33025 (US), E33026 (CE)
NMEA Cable, 5 pin, 1.5m
part no. R08004
Bracket Screws,
No.10 x 3/4 (x3)
Bracket Knobs,
part no. R38107
Mounting Bracket,
part no. R38110
Sun Cover,
part no. R38108
A60
Installation
Manual
RS12 GPS, part no. E33021
Installation Manual,
part no. 87081
GPS Antenna
GPS Gasket
Thumb nuts (x2)
A60
Owner’s
Studs (x2)
Handbook
Pole Mount Bracket
Mount Screws, M4 (x2)
Owner’s Handbook,
part no. 81295
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
11
1.3 Optional Equipment
The following optional items are also available to complete your system:
Part No.
E63070
Description
DSM25, Digital Sounder Module, 200/50KHz, 500W
E36017
R69086
E36015
E36016
E66066
E66070
Flush Mount Kit, A60
Network Cable, A60, 3.5m
Network Cable, A60, 8.5m
Network Cable, A60, 15m
Transducer Adapter, Pathfinder (DSM250) to A Series
Transducer Adapter, Legacy Transducer (L365/L470) to A Series
Download from Www.Somanuals.com. All Manuals Search And Download.
12
A60 Installation Manual
1.4 Unit Size
The dimensions for your A60 display are as follows:
9.61in (244mm)
ENTER
CANCEL
6.81in
RANGE
(173mm)
7.83in
(199mm)
PAGE
ACTIVE
DATA
WPTS
MOB
PWR
MENU
9.88in (251mm)
11.02in (280mm)
2.56in
(65mm)
2.40in (61mm)
.866in (22mm)
3.43in
(87mm)
3.11in
(79mm)
Flush Mount
Bracket Mount
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Chapter 2: Installing the Display Unit
The A60 display unit is waterproof to IPX-7 and can be installed either above or
below deck using either the mounting bracket or by flush mounting into the
console.
2.1 Mounting
Note: The mounting bracket andthe mountframe towhich thebracket attaches must be
removed prior to flush mounting.
Mounting Bracket Method
Themountingbracketcanbeusedtosecurethedisplayunittoadash, charttable,
bulkhead or deckhead.
Mount Frame
Display Unit
Frame Screws (x4)
Mounting Bracket
Bracket Knobs (x2)
D9615-1
You should install the mount bracket as follows:
1. Loosen the knobs and remove the bracket from the unit.
2. Mark the locations of the bracket screw holes on the mounting surface.
3. Drill 9/64” (3mm) pilot holes at the marked locations, taking care that there
are no cables or anything that may be damaged behind the surface.
4. Align the bracket holes with the holes on the mounting surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
A60 Installation Manual
5. Use the screws and nuts supplied to securely attach the bracket to the mount-
ing surface.
1
2
3
x3
x3
D7899-1
6. Attach the display unit to the bracket.
7. Adjust the unit angle for clear vision and tighten the knobs.
Flush Mounting
Flush mounting your display on the console requires the optional E36017 Flush
Mount Kit.
D9616-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installing the Display Unit
CAUTION: Installation
15
Make sure there are no hidden electrical wires or other
items behind the selected location before proceeding.
Make sure there is sufficient rear access for mounting
and cabling.
1. Check the selected location for the unit. A clear, flat area with suitable clear-
ance behind the panel, is required.
2. Attach the template included with the flush mount kit to the selected loca-
tion, using masking or self-adhesive tape, taking care that it is level.
3. Use a hole saw to make a pilot hole in each corner of the cut-out area.
4. Using a suitable saw, cut along the inside edge of the cut-out line.
5. Detachthe mountframefrom theunitbyremovingthefourmounting screws.
Make sure that the unit fits in the area that has been cut out.
6. Drill four 3/16 in (4.5 mm) holes as indicated on the template to accept the
retaining bolts.
7. Place the gasket onto the display unit.
8. Connect the cables to the display, avoiding tight bends.
9. Screw the 4 supplied studs into the rear of the unit.
10. Slide the unit into the console.
11. From the rear, attach the supplied nuts onto the studs and tighten until
secure.
2.2 Cable Runs
When installing system cables consider the following:
•
Allcablesshouldbeadequatelysecured,protectedfromphysicaldamageand
exposure to heat. Avoid running cables through bilges or doorways, or close
to moving or hot objects.
•
•
Avoid acute bends.
Where a cable passes through an exposed bulkhead or deckhead, a water-
tight feed-through should be used.
•
•
Secure cables in place using tie-wraps or lacing twine. Coil any extra cable
and tie it out of the way.
Do not pull cables through a bulkhead or deckhead using a cord attached to
the connector. This could damage the connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
A60 Installation Manual
.
12V Power Supply
RS12
Display Unit
DSM25 Sounder
Fluxgate Compass
GPS
SONAR
AUX
NMEA
POWER
GPS
Power
Power
NMEA
Fishfinder
Transducer
Making the Cable Connections
The cable connections are located on the back of the display unit as shown below:
GPS
SONAR
AUX
NMEA
POWER
D7719-1
Power Input Cable (R08003)
This 1.5m (5 ft) cable is supplied for connecting to your boat’s DC power supply.
DC power is connected at the 3-pin POWER connector on the unit’s connector
panel. The connector (viewed from the outside) and pin functions are shown in
the following diagram and table.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installing the Display Unit
17
1
2
3
D7734-1
Power Connector
Pin No. Function
Color
Red
1
2
3
Battery positive (12 VDC systems)
Battery negative
Black
Shield (drain wire)
No insulation
Power Supply
The A60 is intended for use on boat’s DC power systems rated from 10.7 to
18 VDC. The power connection to the unit should be made at either the output of
the battery isolator switch or at a DC power distribution panel. Power should be
fed directly to the A60 via its own dedicated cable system and protected by a
thermal circuit breaker or fuse on the red (positive) wire that is installed close to
the power connection.
CAUTION: Dedicated Power Connection
The A60 also supplies power for the GPS and sounder units (if so
equipped). To minimize succeptibility to display flickering due to
power fluctuations, provide the display unit with its own
dedicated connection to boat’s power.
TheREDwiremustbeconnectedtothe feedfromthepositive(+)batteryterminal
and the BLACK wire to the feed from the negative (–) battery terminal. The shield
wire (drain) should be connected to the boat’s RF ground.
CAUTION: Fuse Protection
Install a fast blow 4 amp fuse on the red (positive) wire.
Ifalongerpower cablerunisrequired, usethesuppliedpowercableto connectto
thedisplayunit. Thenuseasuitableconnectorblocktoconnectthefreeendtothe
extension cable, taking particular care to ensure the correct polarity.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
A60 Installation Manual
Use commonly practiced methods to determine proper wire gauge based on wire
length, current, and wire tables. You may also trim the power cable supplied with
theA60toreduceoverallwire length. Only use enoughwiretoconnecttheunitto
the power source, including a service loop.
Note: When the A60 has been powered off using the PWR key but is still electrically con-
nected to the power supply, the GPS continues to draw current.
The supplied power cable has a cross section of 10 mm.
CAUTION: Correct Polarity
If the power connections are accidentally reversed the system
will not work. Use a multimeter to ensure that the input power
leads are connected for correct polarity.
NMEA Cable (R08004)
The 5-pin, 1.5m (5 ft) NMEA input cable is supplied with exposed wire connecting
tails. These should be connected to your existing NMEA instruments using
suitable connector blocks as follows:
Function
Color
Green
White
Yellow
Brown
Screen
Pin no.
NMEA Input (-ve) common
NMEA Input (+ve)
NMEA Output (+ve)
NMEA Output (-ve) common
Not connected
1
2
3
4
5
2
3
4
1
D7735-1
5
GPS Cable
Connect the 6-pin RS12 cable to the left-most connector, labeled GPS.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Chapter 3: Installing the GPS Antenna
The RS12 package contains the following items:
1. Low profile GPS Receiver, with 10 m (33 ft) cable
2. Flush mount gasket
3. Mounting studs (x2) and thumb nuts (x2)
4. Pole mount kit *
Note: * If you intend to mount the receiver on a pole, you will need to obtain a suitable
pole with 1 inch 14 TPI thread.
3.1 Selecting the Mounting Location
The RS12 can be mounted on a pole or flush mounted on a suitable horizontal
surface.
Receiver Location
The RS12 receiver is designed to receive the signals emitted from satellites in a
direct path. It should be mounted:
•
•
On a horizontal surface.
In a location that is open and clear of any obstructions (such as masts, search
lights, or other structures) that could block line-of-sight reception of signals.
•
As low as possible: the height of the receiver is not as important as it having a
clear view horizon to horizon for optimum signal reception. In fact, the lower
the unit can be mounted and have a clear view to satellites, the better. The
more stable the unit, the more effectively it will track satellites low tothe hori-
zon.
Note: Do NOT mount the receiver up a mast, as the receiver will swing with the boat,
leading to significant COG/SOG errors.
•
As far as possible from any sources of interference: the receivershould be sep-
arated by at least 1 m (3 ft) from other antennas and electronic equipment. It
should not be mounted in the direct path of a radar’s beam.
When mounting the receiver flush to a surface:
•
•
select an area that allows access to the underside of the mounting surface
avoid areas where the receiver might be stepped on or tripped over
Download from Www.Somanuals.com. All Manuals Search And Download.
20
A60 Installation Manual
Cabling Route
When planning the location for the unit, consider the best route for running the
cable between the receiver and GPS display unit or to the rest of an integrated
system. Ideally, you should try to route the cable so it is:
•
•
hidden from view
separated as far as possible from other cables (to prevent interference)
When running cable, always observe the following guidelines:
•
•
•
•
if a cable has to be fed through the deck, use a good quality deck grommet
where cables are fed through holes, use grommets to prevent chafing
secure long cable runs so they do not present a hazard
wherever possible, route cables away from fluorescent lights, engines and
radio transmitting equipment, as these may cause interference
3.2 Mounting the Receiver
When you have selected a suitable location, follow the installation instructions
for Pole Mounting or Surface Mounting.
Pole Mounting
Note: You will need to obtain a suitable pole with 1 inch 14 TPI thread.
1. Securely attach the pole mount base to a suitable pole or rail mount bracket.
2. Pass the cable through either:
A: the center hole of the pole mount base, or
B: the side exit channel
Note: If you intend to use the side exit channel, remove the two plastic tabs obstructing
the channel. If you do not remove these tabs before using the cable channel, you could
damage the cable.
3. Check the cable is positioned correctly, then secure the receiver to the pole
mount base using the two M4 screws provided.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installing the GPS Antenna
21
.
B
A
D8689-1
Surface Mounting
1. Use the template supplied in this handbook to mark the two 6 mm (0.25 in)
mounting holes.
2. OPTION A:
If the cable is going to pass through the mounting surface drill a 19 mm (0.75
in) center hole.
OPTION B:
If the cable is to exit from the side of the receiver above the mounting sur-
face, remove the two plastic tabs (1) obstructing the cable channel. If you do
not remove these tabs before using the cable channel, you could damage the
cable.
3. Screw the two mounting studs (2) into the underside of the receiver.
4. Stick the supplied gasket (3) to the mounting surface, ensuring that the holes
on the gasket correspond with the drilled holes.
5. Passthecabledownthroughthecenterhole(OptionA)orrouteitthroughthe
cable exit channel (Option B).
6. Carefully position the receiver so the mounting studs pass through the holes
in the mounting surface.
7. Secure the receiver to the surface using the two thumb nuts (4).
Download from Www.Somanuals.com. All Manuals Search And Download.
22
A60 Installation Manual
A
B
1
3
2
2
3
4
Underside view
4
Top view
D8690-1
Making the Cable Connections
Connect the cable to the connector LabeledGPS on the back of the display unit as
shown below:
.
Display Unit
RS12
GPS
SONAR
AUX
NMEA
POWER
GPS
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Chapter 4: Maintenance
4.1 Introduction
This chapter provides information on maintaining and troubleshooting your A60
GPS Chartplotter and on how to get assistance from Raymarine.
At regular intervals, carry out the following servicing procedures:
•
Routine checks.
•
Cleaning the Display.
Do not attempt any other servicing procedures.
Servicing and Safety
•
Raymarine equipment should be serviced only by authorized Raymarine ser-
vice technicians. They will ensure that service procedures and any replace-
ment parts used will not affect performance. There are no user serviceable
parts in any Raymarine product.
•
•
Some products generate high voltages, so never handle the cables or connec-
tors when power is being supplied to the equipment.
When powered on, all electrical equipment produces electromagnetic fields.
These can cause adjacent pieces of electrical equipment to interact with one
another, with a consequent adverse effect on operation. In order to minimize
these effects and enable you to get the best possible performance from your
Raymarine equipment, guidelines are given in the installations manual, to
enable you to ensure minimum interaction between different items of equip-
ment, i.e. ensure optimum Electromagnetic Compatibility (EMC).
•
•
Always report any EMC-related problem to your nearest Raymarine dealer.
We use such information to improve our quality standards.
In some installations, it may not be possible to prevent the equipment from
being affected by external influences. In general this will not damage the
equipment, but it can lead to spurious re-setting action, or momentarily may
result in faulty operation.
Routine Checks
Carry out the following tasks on a regular basis:
•
Examine all cables for signs of damage, such as chafing, cuts or nicks.
•
Check that all cables are securely connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
A60 Installation Manual
Cleaning the Display Window
A coating is applied to the plastic window of your display. This makes it water
repellent and prevents glare. To avoid damaging this coating, the recommended
cleaning procedure must be followed.
CAUTION:
Please read these instructions carefully. Failure to follow the
correctcleaningproceduremaydamageyourdisplaywindowand
invalidate your warranty.
Recommended Cleaning Procedure
1. Power off the display.
2. Rinse the window with fresh water, to remove all dirty particles and salt
deposits.
•
•
•
Do not use any abrasive materials, including a dry cloth.
Do not use any cleaning solutions, polishes or sprays.
Do not use a jet wash.
3. Allow the window to dry naturally.
4. If any smears remain, very gently wipe the window with a clean microfiber
cleaning cloth (not supplied).
4.2 Resetting the System
You can reset the A60 display in one of three ways:
Power-on Reset
Settings Reset
Settings and Data Reset
•
•
•
Power-on Reset
When you reset the system, at power-on the last used values are retained for all
the options, except for those listed in the following table which are reset to the
factory default each time:
Item
Power-on setting
Relative
Relative Motion mode
Brightness
ON at 100%
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Maintenance
25
Settings Reset
The factory reset will set all values back to their original factory settings. The
Waypoint and Route List databases are not reset. There are two ways to carry out
a Settings Reset: using hardware keys or via the System Setup Menu.
To carry out a Settings Reset using the hardware keys:
1. With the A60 powered OFF, press and hold the left hand soft key.
2. Press and release the POWER key to power ON the display, but continue to
hold in the soft key. A countdown message appears. Continue to depress the
soft key until the RESETTING DATABASE message appears.
The reset will take place during this operation.
To carry out a Settings Reset using the System Setup Menu:
1. With the A60 powered ON, press the MENU key.
2. Use the trackpad to navigate to the System Setup menu.
3. Select Settings Reset. A confirmation message appears.
4. Press ENTER to accept the reset or CANCEL to quit without resetting.
Settings and Data Reset
This option returns all settings to their original factory values and deletes all
waypoints and route lists.
To carry out a Settings and Data Reset:
1. With the A60 powered ON, press the MENU key.
2. Use the trackpad to navigate to the System Setup menu.
3. Select Settings and Data Reset. A confirmation message appears.
4. Press ENTER to accept the reset or CANCEL to quit without resetting.
4.3 Troubleshooting
All Raymarine products are, prior to packing and shipping, subjected to
comprehensivetestandqualityassuranceprograms. However, ifyourA60should
develop a fault, this section will help you to identify the most likely cause and
show the corrective action required to restore normal operation.
If, after referring to this section, you are still having problems with your Display,
contact your local dealer, national distributor or Raymarine Technical Services
Department for further advice.
Always quote the product serial numbers, which are printed on the back of the
unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
A60 Installation Manual
Common Problems and How to Solve Them
Problem
Solution
Display is blank
1. Make sure that the power supply cable is sound and
that all connections are tight and free from corrosion.
2. Check relevant fuses.
3. Make sure that Brightness level is not set too low.
“NO DATA SOURCE”
message
The boat’s power system must be capable of delivering at
least 10.8 VDC at 4 amps. Check for:
•
•
Inadequate wire gauge or excessive wire length
Too many other electronics devices connected on the
same circuit
•
•
•
Loose connections
Corroded fuse blocks and fuses
Low battery charge
“Invalid software: Version Incorrect software version installed. Contact your local
xx.x, Version xx.x required” Raymarine dealer or visit the Customer Support section of
raymarine.com.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Maintenance
27
4.4 Upgrading the Display
Raymarine occasionally issues software updates for adding new features and
improving product performance. The A60 includes a Software Upgrade Utility for
installing these updates when they become available.
Product updates are generally available on the Raymarine website, under
Customer Service/Software and Firmware upgrades. The update process requires:
•
•
•
A CompactFlash (CF) memory card. Any card of 8 MB capacity or larger will
usually work. Do not use the Navionics chart card for this procedure.
A CompactFlash reader/writer, which allows you to move files between your
CF card and personal computer.
A personal computer, Windows or Mac compatible.
To upgrade your A60:
1. Connect the CompactFlash reader/writer to your computer and load the
CompactFlash memory card into it.
2. Download the update files from the Raymarine web site to your computer,
according to the instructions on the web site.
3. Copy the files from your computer to the root directory of your CompactFlash
memory card. For example, if your CompactFlash card reader is identified by
the computer as drive ‘E:’, open this drive and paste the files there.
4. Remove the CompactFlash card from the reader/writer.
5. Make sure the A60 and DSM25 (if one is installed) are fully connected but
powered OFF. (The DSM25 must be connected for it to be updated.)
6. Insert the CF update card into the A60 chart card reader.
7. Power ON the A60. The following screen appears.
The Upgrade Package Available field displays the contents of the card. Local
Unit Details displays the file versions currently installed in your A60.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
A60 Installation Manual
Raymarine Software Upgrade Utility
Upgrade Packages Available
Upgrade Package Details
Title: A60_BTLD_UPD
Version: 2.02
Created: 27 Oct 2006 19:07
Label: Build
A60_BTLD_UPD
A60_APP_UPD
2.02
2.28
Contents
of CF card
DSM25_BTLD_UPD 2.02
DSM25_APP_UPD 2.02
Details of the
Machine: LOCAL
Product: D675 A60 Display
highlighted file
File:
A60BTLD.PKG
Local Unit Details
NAME A60 Display
FAMILY A Series
PRODUCT: D675
Version status
of your A60
SERIAL# 25525532767
BOOT:
APP:
FPGA:
V1.28
V1.44
V01.00.018
Use Navigation Keys to Select Upgrade
Then Press Upgrade or Enter Key
After Upgrade Remove Card and Reboot
Upgrade
Reboot
8. Compare the upgrades that are available in the Upgrade Packages Available
field with the version displayed in Local Unit Details. If a newer version is
available under Upgrade Packages Available, use the trackpad to highlight
that file.
Note: If installing multiple files, upgrade one at a time and reboot only after all upgrades
have been installed.
9. Press the Upgrade soft key. An upgrade progress bar replaces the two soft
keys. You are prompted to confirm the upgrade.
10. Press Continue to confirm. When complete, the following message appears:
“Upgrade Completed. Press ANY KEY to Continue”.
11. Press a key on the A60. The Upgrade and Reboot soft keys now replace the
text.
12. Highlight and install any other updates as needed, one file at a time, by
repeating steps 9–11.
13. When finished installing the updated files, remove the Compact Flash card
from the A60 card reader and replace it with your Navionics chart card.
14. Press Reboot. The following message appears: “Press ENTER to Continue or
ANY KEY to Abort”.
15. Press ENTER. The unit restarts. The upgrade is complete.
You can verify the version numbers by viewing Unit Information in the Diag-
nostics Menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Maintenance
29
4.5 Technical Support
Raymarine provides a comprehensive customer support service, on the world
wide web, through our worldwide dealer network and by telephone help line. If
you are unable to resolve a problem, please use any of these facilities to obtain
additional help.
Worldwide Web
As well as providing a comprehensive Frequently Asked Questions section and
servicing information, the website also gives e-mail access to the Raymarine
TechnicalSupportDepartmentandadetailsofthe locations ofRaymarineagents,
worldwide.
Navigate to the Customer Support page for links to:
•
•
•
•
•
Finding Factory Service locations and Authorized Dealers near you
Registering your Raymarine products
Accessing handbooks in Adobe Acrobat format
Downloading RayTech software updates
Accessing the Raymarine solution database
Clicking the Find Answers link routes you to our solution database. Search
questions and answers by product, category, keywords, or phrases. If the answer
you are seeking is not available, click the Ask Raymarine tab to submit your own
question to our technical support staff, who will reply to you by e-mail.
If you don’t have access to the world wide web, contact Technical Support where
specialists are available to answer questions about installing, operating and
trouble-shooting all Raymarine products.
Help us to help you
When requesting service, please quote the following product information:
•
•
•
•
Equipment type
Model number
Serial number
Software issue number
Download from Www.Somanuals.com. All Manuals Search And Download.
30
A60 Installation Manual
Contacting Raymarine in the US
You can contact Raymarine in the US either using the Raymarine world wide web
as detailed above or by calling one of the telephone numbers below.
Accessories and Parts
You can obtain many Raymarine accessories and parts directly from your
authorized Raymarine dealer. However, if your dealer does not have the item you
want, contact Raymarine Technical Services at:
603-881-5200 extension 2333.
You can use these numbers Monday to Friday 8:00 AM to 6:00 PM Eastern
Standard Time or Eastern Daylight Savings Time.
If you are not sure which item is appropriate for your unit, you should first contact
the Technical Support Department at:
603-881-5200 extension 2444.
to verify your requirements.
Product Repair and Service
In the unlikely event that your Raymarine unit should develop a problem, contact
your authorized Raymarine dealer for assistance. The dealer is best equipped to
handle your service requirements and can offer timesaving help in getting your
equipment back into normal operation.
If repairs cannot be obtained conveniently, obtain product service by returning
the unit to:
Raymarine Product Repair Center
21 Manchester Street
Merrimack, NH 03054
The Product Repair Center is open Monday to Friday 8:15 AM to 5:00 PM Eastern
Standard Time or Eastern Daylight Savings Time.
All products returned to the Repair Center are registered upon receipt and a
confirmation letter is sent to acknowledge the repair status and the reference
number of the product.
We will make every effort to carry out the repair and return your unit as quickly as
possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Maintenance
31
If you wish to enquire about the repair status of your unit, contact the Repair
Center at:
603-881-5200 extension 2118.
Contacting Raymarine in Europe
You can obtain Technical Support, service and accessories from your authorized
Raymarine dealer, or by contacting:
Raymarine plc
Robinson Way
Anchorage Park
Portsmouth PO3 5TD
United Kingdom
Tel +44 (0)23 9271 4713
Fax +44 (0)23 9269 4642
Download from Www.Somanuals.com. All Manuals Search And Download.
32
A60 Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Appendix: Specifications
A60 LCD Color Display
General
Approvals
CE - conforms to
2004/108/EC (EMC), EN60945:2002
Mounting
Bracket with dash (flush) mount option
Size (H x W x D)
7.8 x 11.0 x 3.1 in (199 x 280x 79 mm), bracket mounted
6.8 x 9.6 x 2.4 in (173 x 244 x 61 mm), dash mounted
Weight
Power
3.09 lbs (1.40 kg), bracket mounted
2.25 lbs (1.02 kg), dash mounted
External 10.7–18.0 VDC required, 13.8 VDC nominal
Floating earth/ fully isolated
Consumption with full brightness: 9 W
Environmental:
Waterproof to IPX7; suitable for external mounting
Op/Storage Temp. Range 14° F to 122° F (–10° C to + 50° C)
Humidity limit
up to 95% at 35° C non-condensing
9 defined keys, 5 soft keys, trackpad and rotary control
Color TFT LCD
Controls
Display type
Resolution
320 x 240 pixels (¼ VGA)
Display size
Display Windows
Brightness
5.7 in
Chart, Fishfinder and Data
Screen and keypad illumination: 0 to 100% in 20 steps
UK English, US English, Danish, Dutch, Finnish, French,
Languages
German, Icelandic, Italian, Norwegian, Portuguese, Spanish,
Swedish
Alarms
Anchor, Arrival, Battery, Deep Depth, MOB, Off Track, Fish,
Shallow Depth, Temperature
Connectors
3 pin POWER
5 pin NMEA
8 pin AUX
8 pin SONAR
6 pin GPS
Download from Www.Somanuals.com. All Manuals Search And Download.
34
A60 Installation Manual
General
Interfaces
RS12 GPS Antenna
DSM25 Sounder
NMEA0183, receive and transmit
CompactFlash card slot
Man Overboard (MOB
Mode)
Markplacedwithcourse line;readoutshowsrange, bearing,
and lat/long of MOB
Screen functions
Full and half screens available dependent on function.
Chartplotter Features
Cartography
Navionics Charts on CompactFlash cards
Chart of the world built in
Chart scaling
1/32nm minimum range
Presentation Modes
Head up, Course up or North up
(selectable True or Magnetic, Relative or True Motion)
Waypoints
1000 waypoints entered via cursor, lat/lon or at boat’s
position.
16 character name can be assigned.
6 different waypoint symbols available
Additional storage available on CompactFlash cards
Waypoint Transfer
Routes
Waypoints database via NMEA or CompactFlash card
Up to 495 routes can be stored in the unit’s internal
memory. A route plan may contain up to 50 waypoints.
Same waypoint can be used in multiple routes.
Additional storage available on CompactFlash cards.
Feature to create a route from track history; up to 50
waypoints created to form new route.
Navigation information
Track History
Status Bar at top of screen displays chart range, orientation,
relative motion mode, and position data.
16 tracks with up to 1000 points in each can be stored in the
units internal memory.
Track optimization reduces number of points used.
Additional storage available on CompactFlash cards
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: Specifications
35
Interfacing
DSM connection
For communication with DSM25
NMEA Input - NMEA 0183
APB Auto Pilot sentence “B”
BWC Bearing & distance to waypoint, great circle
BWR Bearing & distance to waypoint, rhumb line
DBT Depth Below Transducer
DPT Depth of water
GLL
Geographic position, Latitude/Longitude
GGA Global positioning system fix data
HDG Heading, deviation & variation
HDM Heading, magnetic
HDT Heading, true
RMA Recommended minimum data for LORAN-C
RMB Recommended minimum navigation data
RMC Recommended minimum data for GPS
RTE
Routes
VHW Water speed & heading
VLW Distance traveled through the water
VTG Vector Track and Ground speed
WPL Waypoint location
XTE
Cross Track Error, measured
ZDA Time & date
NMEA Output - User
selectable
APB Auto Pilot sentence “B”
BWC Bearing & distance to waypoint, great circle
BWR Bearing & distance to waypoint, rhumb line
DBT Depth Below Transducer
DPT Depth of water
GLL
Geographic position, Latitude/Longitude
MTW Water Temperature
RMB Recommended minimum navigation data
RMC Recommended minimum data for GPS
RTE
Routes
VHW Water speed and heading
VLW Distance traveled through the water
VTG Vector Track & Ground speed
ZDA Time & date
Download from Www.Somanuals.com. All Manuals Search And Download.
36
A60 Installation Manual
RS12 GPS Antenna
Approvals
CE - conforms to
2004/108/EC (EMC)
Dimensions:
diameter: 3.7 in (95 mm)
height:1.2in(30mm);2.4in(62mm)withpolemount
kit
Weight:
15.3 oz (0.435 kg)
33 ft (10 m)
Cable length:
Receiver type:
SD-GPS, WAAS/EGNOS/MSAS ready, 12 parallel
channels
Operating conditions:
temperature range: 14°F to 158°F (–10°C to 70°C)
water protection: waterproof to CFR46
Storage conditions
Frequency
temperature range: 14°F to 158°F (–10°C to 70°C)
1575.42 MHz 1 MHz (C/A code), L1
Sensitivity
Tracking: –152 dBm
Acquisition: –139 dBm
Signal acquisition:
Automatic
Time to first fix (TTTF):
Hot start < 6 seconds (typical);
Warm start < 40 seconds (typical);
Cold start < 60 seconds (typical)
Position accuracy:
Speed accuracy:
Geodetic datum:
2 DRMS ~ 2 m 95%
0.1 kts RMS
WGS-84
Download from Www.Somanuals.com. All Manuals Search And Download.
37
M
Index
Mounting
A60 13, 14
RS12 20, 21
A
A60
N
Bracket mounting 13
Cable connections 16
Cable runs 15
Dimensions 12
Flush mounting 14
Installation 13
NMEA cable 18
Power 17
NMEA Cable 18
O
Optional equipment 11
P
Phone numbers 30
Pole mounting, RS12 20
Power
Specifications 33
Connections 16
Supply 17
B
Problem solving 26
Bracket mounting, A60 13
R
C
Reset 24
Cable
RS12
Connections, A60 16
Connections, RS12 22
Installation requirements 20
NMEA 18
Cable connections 22
Pole mounting 20
Specifications 36
Surface mounting 21
Power 16
Running, A60 15
Cleaning 24
S
Safety notices 5
Size 12
D
Specifications 33
A60 33
Dimensions 12
E
RS12 36
EMC conformance 7
Equipment
Optional 11
Standard 10
Standard equipment 10
Surface mounting, RS12 21
System reset 24
T
F
Technical support 29
Troubleshooting 26
Ferrites 7
Flush mounting, A60 14
Fuse 17
U
Upgrade Utility 27
I
Installation
A60 13
RS12 19
Download from Www.Somanuals.com. All Manuals Search And Download.
38
A60 Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
19mm (0.75") dia.
for cable and plug
36mm (1.4in)
18mm
(0.7in)
6mm (0.25") dia.
2 positions
6mm (0.25") dia.
pilot hole
Cable Exit Channel
D4194-2
GPS Antenna Mounting Template
Note: Be sure to leave sufficient spacing beneath the mounting surface for the mounting
nuts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
Raymarine World Wide Warranty
Raymarine Inc.
APPLICABLE TO PRODUCTS SOLD THROUGH OFFICIAL RAYMARINE INC. DEALERS, DISTRIBUTORS AND BOAT
BUILDERS WITHIN THE AMERICAS AND CARIBBEAN.
Limited warranty
Subject to the terms, conditions and limitations set forth in this U.S. Limited Warranty (hereinafter the ‘Warranty’),
Raymarine warrants that its products, when properly installed and used, will be free from defects in material and
workmanship for a period of twenty-four (24) months (with respect to VHF radios, a period of thirty-six (36) months),
from the date of first purchase (the ‘Warranty Period’).
For the purposes of this warranty, ‘date of first purchase’ means the date that the product was purchased by the first
retail customer; or in the case of a product installed on a new vessel by a certified Raymarine original equipment
manufacturer (a ‘Raymarine OEM’), the date that such vessel was purchased by the first retail customer.
Raymarine will, at its sole option, repair or replace any defective products or components returned during the
Warranty Period in accordance with the terms, conditions and limitations set forth below. Such repairs or
replacement will be the sole remedy of the customer under this Warranty.
Obtaining Warranty Service
Standard Warranty Service
To qualify for standard warranty service the product must be returned to a Raymarine-certified service agent, or
directly to Raymarine in person, orby mail (i) within the Warranty Period, and (ii) within thirty (30)days ofthe alleged
product failure.Any products returned by mail must be securely packaged and sent pre-paid and insured to
Raymarine or to a Raymarine-certified service agent. All products, whether returned in person or by mail, must be
accompanied by a copy of the original sales receipt, to be eligible for standard warranty service.
A list of Raymarine-certified service agents is available from Raymarine Technical Support or at
‘On Board’ Warranty Service
For any Raymarine product or system that (i) has been installed on your vessel by a Raymarine-certified service agent
or by a Raymarine OEM, and (ii) hasa MSRP equal to orgreater than USD $2,500, you areeligible to receivewarranty
service by a Raymarine certified service agent on-board your vessel (‘On Board Warranty Service’) for a period of 12
months from the date of first purchase of such product or system, or the date of first purchase of the vessel on which
such product or system has been installed (the ‘On Board Warranty Period’). In order to obtain On Board Warranty
Service eligible customers MUST:
•
(i) within the On Board Warranty Period, and (ii) within thirty (30) days from the date of the
alleged failure giving rise to the warranty claim for which you are requesting On Board Warranty
Service, contact a local Raymarine-certified service agent and request On Board Warranty Ser-
vice.
•
Present to the Raymarine-certified service agent a copy of the original sales receipt for the prod-
uct, together with proof of the date of installation of the product by a Raymarine-certified service
agent. The service agent may at its sole option, accept or deny such proof of purchase and proof
of installation as sufficient to qualify you for On Board Warranty Service.
Costs associated with travel, mileage, taxi fares, launch or docking fees, aircraft or vehicle rental, meals, customs,
shipping, communication charges, and service agent travel costs are specifically excluded from coverage under this
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
Warranty and are your responsibility. In addition, this Warranty does not cover fees associated with hauling,
shipping or towing your vessel to a Raymarine-certified agent.
UpontheexpirationoftheOn BoardWarrantyPeriod, youarestilleligibleto receivestandardwarranty serviceforthe
remaining term of the Warranty Period, but will not be eligible for continued On Board Warranty Service.
Limitations and Exclusions
In addition to any other limitations and exclusions set forth herein, Raymarine is not responsible for, and this
Warranty does not cover:
•
•
•
failures due to abuse, misuse, accident, unauthorized alteration or repair, improper installation
(whether or not by a Raymarine-certified service agent), shipping damage or corrosion;
Costs associated with routine system checkouts, alignment/calibration, seatrials or commission-
ing;
repair or replacement of consumable items, including, without limitation, fuses, batteries, drive
belts, radar mixer diodes, snap-in impeller carriers, impellers, impeller bearings and impeller
shafts;
•
•
costs associated with overtime or premium labor costs;
differences in material, coloring or size that may exist between actual products and the pictures
or descriptions of such products in our advertising, advertising literature or on the Internet;
products purchased by a customer from a United States dealer via the Internet if such products
were not delivered and installed within the United States; or
the replacement of missing components from the package of any product purchased through an
online auction site.
•
•
Other conditions
ThisWarranty isfullytransferableprovidedthatyou furnishtheoriginalproofofpurchasetoRaymarineor, in thecase
of On Board Warranty Service, to a Raymarine-certified service agent. This Warranty is void if the label bearing the
serial number has been removed or defaced.
TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW, THE FOREGOING WARRANTY IS
RAYMARINE’S SOLE WARRANTY AND IS APPLICABLE ONLY TO NEW PRODUCTS PURCHASED IN THE
UNITED STATES OF AMERICA. THE PROVISIONS OF THIS WARRANTY ARE IN LIEU OF ANY OTHER WRITTEN
WARRANTY, WHETHER EXPRESSED OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THE LIABILITY OF RAYMARINE TO A CUSTOMER UNDER THIS WARRANTY, WHETHER FOR BREACH OF CONTRACT,
TORT, BREACHOFSTATUTORY DUTY OR OTHERWISE SHALLIN NO EVENTEXCEED AN AMOUNT EQUALTO TEN (10)
TIMES THE MANUFACTURER’S SUGGESTED RETAIL PRICE OF THE PRODUCT GIVING RISE TO SUCH LIABILITY AND
IN NO EVENT SHALL RAYMARINE BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM JURISDICTION TO
JURISDICTION.
This Warranty supersedes and replaces all previous Warranties.
January 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
Raymarine UK Ltd.
APPLICABLE TO PRODUCT SOLD THROUGH OFFICIAL RAYMARINE UK LTD. DEALERS, DISTRIBUTORS AND BOAT
BUILDERS WITHIN EUROPE, THE MIDDLE AND FAR EAST, AFRICA AND AUSTRALASIA.
Limited Warranty
The Raymarine warranty terms and conditions as described below do not affect the customers legal rights and
complies with EU Directive 1999/44/EC.
In order to ensurethat the productcontinues to operate efficiently and reliably, we recommend that, beforeusingthe
product, the customer carefully reads the Owner’s Handbook and follows the advice on the safe and correct
operation and use of the product. We recommend that the Raymarine product is installed by a Raymarine certified
installer. Installation by persons other than a Raymarine certified installer may invalidate the warranty.
1. Product warranty
1.1 Raymarine warrants each new product to be of good materials and workmanship. Raymarine, or its approved
agents, will repair or exchange under warranty any parts or product proven to be defective in material or
workmanship under normal use, for a period of2 years (24 months) from dateof sale to end user, subject to the limits
contained in this warranty document.
1.2 The Raymarine warranty covers the parts and labour associated with any warranty repair as described above,
provided that the product is returned to Raymarine or one of its approved agents.
1.3 Raymarine reserve the right to replace under warranty, not repair, certain Raymarine products subject to the
limitations below, provided that they are returned to the nearest Raymarine National Distributor. For details of such
products refer to the internet at www.raymarine.com or contact your nearest Raymarine National Distributor.
2. Onboard warranty
2.1Inadditionto theProductwarrantycoverasdescribedabove, Raymarinewill, authorizeonboardwarrantyservice
by the nearest Raymarine approved service agent, subject to the maximum mileage and other limits referred to in
paragraph 4.12 below, on products, where proof of installation, or commission by Raymarine certified installers, can
be shown.
2.2 The warranty provides for onboard repair or exchange of the product, by Raymarine or its approved service
agents, for a period of 2 years (24 months), subject to the limits contained in this warranty document. In the case of a
productinstalled, bya Raymarine certifiedOEMinstaller, on anewboatpriorto thesaleoftheboat toa customer, the
2-year period will begin on the date of the sale of the boat to the customer. In the case of a product installed, by a
Raymarine certified installer, on a boat already in the possession of the customer, the 2-year period will begin on the
date of the commissioning of the installed product.
2.3 Certain Raymarine products are not covered by onboard warranty unless the products are pre-registered and on
board warranty is purchased from theRaymarinecertified installer. For details ofsuch productsreferto the internetat
2.4 The Purchaseable onboard warranty is subject to the limitations below.
3.Obtaining warranty service
3.1 In the event of warranty service being required, the customer should contact Raymarine Technical Support or the
nearest Raymarine approved service agent - the contact details of Raymarine Technical Support and a full list of the
names and details of worldwide service agents are available on the internet at www.raymarine.com and in the
Owner’s Handbook.
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
3.2 In cases where the customer is requesting a warranty service and a Raymarine certified installer has not installed
theproduct;i.e. Productwarranty, theaffected productmustbereturnedto thecustomer’slocal Raymarineapproved
service agent or direct to Raymarine with:
3.2.1 proof of purchase showing the date of purchase and the name of the supplier of the prod-
uct; and
3.2.2 the serial number of the affected product; or
3.2.3 a warranty card completed by the product supplier (which will contain the information
required by paragraphs 3.2.1 and 3.2.2).
Subject to the limitations below, the product will be repaired or replaced (at the discretion of Raymarine or a
Raymarine Service Agent) at no further cost and promptly returned to the customer.
3.3 In cases where the customer is making a warranty claim and the product has been installed by a Raymarine
certified installer, (boat builder, installer, dealer etc.) i.e. Onboard warranty, the nearest Raymarine approved service
agent should becontacted and onboard servicerequested(which willbesubjectto thelimitsreferredtoin paragraph
4.12 below). Before the onboard warranty service is performed, the customer must have available:
3.3.1 proof of purchase showing the date of purchase and the name of the supplier of the prod-
uct; and
3.3.2 the serial number of the affected product; or
3.3.3 proof of installation of the product by a Raymarine certified installer; or
3.3.4 a warranty card completed by the product supplier (which will contain the information
required by paragraphs 3.3.1 and 3.3.3).
3.4 In cases where onboard warranty has been purchased - as described in 2.3; the nearest Raymarine approved
serviceagentshouldbecontactedandonboard servicerequested, informationdetailedin3.3.1 and 3.3.2 isrequired.
Onboard warranty service will only be performed if the product serial number confirms that the onboard warranty
service has been purchased and is valid.
4. Warranty limitations
4.1 Raymarine warranty policy does not apply to any product that has been subjected to accident, abuse or misuse,
shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or products on which the serial
number has been altered, mutilated or removed.
4.2 Certain productsdo not carry the onboardwarranty, as described insection 2 above, unless theonboard warranty
cover is purchased at the time of installation. The purchaseable onboard warranty is only available on products
purchased in specific territories, for further details refer to the internet at www.raymarine.com or contact your
nearest Raymarine National Distributor.
4.3 Products purchased outside the country of installation will not be covered by onboard warranty.
4.4 Raymarine assumes no responsibility for damage incurred during installation or as a result of improper
installation.
4.5 Thiswarranty does notcover routine system checkouts, alignment/calibration, seatrialsorcommissioning, unless
required by replacement of part(s) in the area being aligned.
4.6 Raymarine assumes no responsibility for damage caused by or to other equipment, systems or components
occasioned by improper or unauthorized connection, or use, of the product.
4.7 Consumable items, including, but not limited to: fuses, batteries, drive belts, radar mixer diodes, snap-in impeller
carriers, impellers, impeller bearings, and impeller shafts are specifically excluded from this warranty. A complete list
of the consumable items relating to each product can be found in the Owner’s Handbook and/or on the internet at
4.8 All costs associated with transducer replacement, other than the cost of the transducer itself, are specifically
excluded from this warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
4.9 Overtime/premium labour portion of services outside of normal working hours is not covered by this warranty.
4.10 If repairs are necessary under the warranty, the affected product must be forwarded to a Raymarine facility or a
Raymarine approved service agent, at the owner’s expense.
4.11 The Raymarine warranty does not cover any differences in material, coloring or size between those alluded to in
corporate advertising, literature or published on the internet, which are not specifically objected to at the time of
delivery.
4.12 Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded from the
warranty on all products. Costs, which areexcluded from thecoverageofthiswarranty, include butare notlimited to;
taxi fares, launch fees, aircraft rental, subsistence, customs, shipping, and communications charges etc.
4.13 Neither Raymarine nor a Raymarine service agent shall be liable for any incidental, indirect, consequential or
special (including punitive or multiple) damages, nor shall Raymarine or a Raymarine service agent be liable for any
lossofprofit, business, contracts, opportunity, goodwillorothersimilarloss. TheliabilityofRaymarineoraRaymarine
service agent to a customer under this warranty, whether for breach of contract, tort, breach of statutory duty or
otherwise, shall not exceed US$1,000,000. Nothing in this paragraph 4.13 shall limit the liability of Raymarine or a
Raymarine service agent in respect of death or personal injury caused by its negligence, fraud or any other liability
which by law, cannot be excluded or limited.
4.14 All Raymarine products sold or provided hereunder are merely aids to navigation. It is the responsibility of the
user to exercise discretion and proper navigational skill independent of any Raymarine product.
Document Number 80009_1
January 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Raymarine World Wide Warranty
Raymarine Service Centers....
United States
Europe, Middle and Far East,
Africa and Australasia
Technical Support
Services
Accessories
Raymarine Technical Support
1-800-539-5539 extension 2444, or
(603) -881-5200
Raymarine plc
Anchorage Park
Portsmouth
PO3 5TD
Product Repair and Service
Raymarine Product Repair Center
21 Manchester Street,
Merrimack, NH 03054 - 4801
1-800-539-5539
England
Tel:
Opening hours:
+44(0)23 9271 4713
Monday through Friday 0815 - 1700
Eastern Standard or Eastern Daylight
Savings Time.
Fax:
+44(0)23 9266 1228
Help us to help you
When requesting service, please quote the following product information:
Equipment type Model number Serial number
Stick barcode label here
Purchased from
Dealer address
Purchase date
Installed by
Installation date
Commissioned by
Commissioning date
Owners name
Mailing address
Download from Www.Somanuals.com. All Manuals Search And Download.
Document number 84065_8
June 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Document number 84065_8
June 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|