Raymarine Fish Finder L265 User Guide

Distributed by

Any reference to Raytheon or

RTN in this manual should be

interpreted as Raymarine.

The names Raytheon and RTN

are owned by the

Raytheon Company.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Echo sounding – How it works (inside front cover)

FishFinder L265 – Features and functions

For information and service ii

Introduction 1

About the FishFinder L265

System Components

Standard Equipment

Standard Transducers

Optional Accessories

Installation 4

About the Transducer

Selecting the Correct Type of Transducer

Assembling the Transducer Bracket

Positioning the Transom-Mount Transducer

Mounting the Transom-Mount Transducer

Mounting the Optional Sidelooker Transducer 10

Installation Notes – Thru-Hull or Low-Profile Transducer 11

Installation Notes – In-Hull Transducer 13

Installation Notes – Trolling Motor Transducer 13

Mounting the Display Unit – Standard Mount 14

Dismounting the Display Unit 15

Mounting the Display Unit – Flush Mount 15

Installing the Transducer Cable 18

Installing the Transducer Cable – Sidelooker Option 20

Making the DC Power Connections 20

Operating Instructions 23

Controls on Display Unit 23

Turning the Power On and Off 24

Setup Memory 24

Lamp/Contrast Menu 25

Selecting Displays 24

Operating Pages 27

FishFinder Page 28

Choosing a Frequency 32

Fish Indications 33

Bottom Indications 35

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance Modes 36

Zoom Page 37

A-Scope (Bottom Coverage) Page 39

Digital Page 41

Sidelooker Page 42

Setup Instructions 46

The Setup Menu 46

Range Setting 47

Sensitivity Setting 48

Chart Speed Setting 49

Zoom Setting 50

Frequency Setting 52

System Setup Display 53

Simulator 54

Deep Alarm 55

Fish Alarm 56

Buzzer 56

Fish Symbol 54

White Line 54

Sidelooker 55

Shallow Alarm 55

Depth Units 57

Setup Instructions for Sidelooker 57

Resetting the Unit to Factory Defaults 59

Default Settings 59

Maintenance andTroubleshooting 60

Cleaning Instructions 60

Troubleshooting Suggestions 60

How to Contact Raymarine 64

Specifications 68

General Information 68

FishFinder Functions 69

Connector Diagrams 70

Glossary of Terms 71

Warranty 73

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Figures

Figure

Page

Unit in Use

Inside front cover

Front Panel

1-1 Typical Installation

2-1 Transducer Types

2-2 Assembling the Transducer Bracket

2-3 Transducer Mounted on Transom

2-4 Transducer Bracket, Side View

2-5 Correct Mounting Position

2-6 Mounting the Transducer

2-7 Installing the Sidelooker Transducer

2-8 Installing the Sidelooker Transducer on a Trolling Motor 14

2-9 Installation on Bracket

2-10 Dimensions

2-11 Flush-Mount Installation

2-12 Disassembling from Bracket

2-13 Installing Cable on Transom

2-14 Cable for Sidelooker Transducer

2-15 DC Power Connections

3-1 Display Panel

3-2 Lamp/Contrast Menu

3-3 Selecting Display Pages

3-4 FishFinder Page

3-5 Fish Indications

3-6 Bottom Conditions

3-7 Zoom Page

3-8 A-Scope Page

3-9 Digital Page

3-10 Sidelooker Feature

3-11 Sidelooker Page

4-1 Moving Through the Setup Menu

4-2 Range Settings

4-3 Sensitivity Setting

4-4 Changing the Chart Speed Setting

4-5 Chart Speed Setting

4-6 Zoom Settings

4-7 Frequency Setting

4-8 Reaching the System Setup Display

4-9 System Setup Display

4-10 Sidelooker Range Settings

4-11 Sidelooker Sensitivity Settings

5-1 Sample Mailing Label

6-1 Connectors

Download from Www.Somanuals.com. All Manuals Search And Download.

1 – Introduction

About the FishFinder L265

The FishFinder L265 is a system that uses sound waves (“sonar”) to

detect fish and show the bottom of a lake or sea. The system includes a

transducer and a display unit, connected by a cable. The transducer

sends high-frequency sound waves down into the water. These sounds

strike fish, the bottom, or other objects in the water, and return as echoes.

The FishFinder then interprets these echoes and presents a display.

The FishFinder L265 can handle many different jobs:

•

detect the presence of fish below the boat

trigger an alarm when fish are found

measure the depth of the water

set alarms for minimum and maximum depth

show the shape of the bottom

determine whether the seabed is hard or soft

We are sure you will find the FishFinder L265 to be one of the most useful

devices on your boat.

Raym arine

PWR

FishFinder 265

Display Unit

AGE

SETUP

CLEAR

L265

Optional Thru Hull

Transducer

Transducer mounted

in quick release

transom bracket

Fig. 1-1

Typical Installation

Introduction

Download from Www.Somanuals.com. All Manuals Search And Download.

System Components

The FishFinder L265 consists of a compact display unit connected to a

transducer. The transducer is attached to the boat and extends into the

water.

Standard Equipment

When you unpack your FishFinder L265, you should find the following

standard equipment in the carton. If any items are missing, please notify

your Raymarine dealer immediately, or contact the Customer Service

Department at Raymarine at 1-800-539-5539, ext. 2333. Please provide

the serial number of the FishFinder when reporting any missing items.

Description

Part No.

FishFinder L265 display unit

(including attached yoke bracket)

E61006

Quick-release swivel-mount bracket

(with mounting hardware)

M78945

M99-146

G627295-2

DC power cable

Instruction manual

10 x 3/4” ss mounting screws (qty. 4)

Standard Transducers

Depending on which model of the L265 you have purchased, the box will

include one of the transducers listed below:

Description

Part No.

Transom-mount transducer (including

mounting bracket and hardware)

M78890

M78922

M78921

Low-profile thru-hull transducer (Valox plastic)

Bronze thru-hull transducer

Optional Accessories

Optional accessories and parts can be purchased directly from

Raymarine. For prices and ordering information, please call the Parts

Department at (800) 539-5539 ext. 2333.

Introduction

Download from Www.Somanuals.com. All Manuals Search And Download.

Description

Part No.

Sidelooker transom-mount transducer

M78930

Sidelooker transducer for trolling motor mounting.

Companion with M78928 downlooker depth

transducer, with 12 ft. (3.6 m) cable

and hardware

M78929

Extension for transducer cable (15 ft, 5 m)

M99-140

M99-139

M99-137

Extension for transducer cable,

for Sidelooker transducer (15 ft, 5 m)

Flush-mounting kit (with hardware and

mounting template)

Fairing block for M78921 thru-hull transducer

(Lexan plastic)

M99-141

In-hull/trolling motor transducer (for installation in

fiberglass hull only, or mounting on trolling motor,

including hardware for either installation)

M78928

M78946

Angled in-hull transducer (for installation in

fiberglass hull only, where deadrise angle is

10° to 22°)

Replacement transom-mount transducer

mounting bracket kit

M99-148

M99-114

Soft storage/carrying case

Transducer switch box (select between two L265

FishFinder displays, using one transducer)

M99-136

Introduction

Download from Www.Somanuals.com. All Manuals Search And Download.

2 – Installation

The installation process has four parts:

•

Mounting the transducer

Mounting the display unit

Connecting the cables for the transducer and power supply

Calibrating the display unit

About the Transducer

Several different kinds of transducers can be used with this unit. The

transom-mount style, used most often, and in-hull types are shown in Fig.

2-1. All of these transducers measure the water depth. An optional

transducer, the Sidelooker, detects objects by looking out to the sides of

the boat.

Since the transducer is very important to the operation of the FishFinder,

it is vital that the transducer be mounted correctly. The transducer will

give the most reliable readings if it looks into water which is smooth and

undisturbed. If you place the transducer so bubbles or turbulence flow

across the face of the unit, the system may give inaccurate readings.

There are three important rules when mounting any type of transducer:

•

The transducer should be continuously covered by water when the

boat is moving. (If the transducer is mounted near the side of the

boat, it may be exposed when the boat is turning.)

The transducer should be placed where turbulence or bubbles will not

pass directly over the face of the unit. Don’t place the transducer

behind any running strakes, intakes, or thru-hull fittings which create

turbulence.

•

The transducer should be mounted where it will not be affected by the

wash from the propeller(s).

Selecting the Correct Type of Transducer

Before you begin the installation, double-check to be sure you have the

correct type of transducer. Each kind of transducer is designed for a

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

M99-141

Fairing for

thru-hull transducer

M78990

Transom-mount

transducer

M78921

Thru-hull

transducer

M78922

Low profile

transducer

M78946

In-hull

transducer

M78930

Sidelooker

transducer

M78928

Sidelooker

transducer for

trolling motor

Fig. 2-1

Transducer

Types

particular type of use. In this manual we will include detailed mounting

instructions for the transom-mount transducer. We will also include some

general information on the other types. For detailed information on these

other transducers, see the instructions which are packaged with the unit.

Use a transom-mount transducer if –

. . . your boat has an outboard or inboard-outboard engine(s), and if you’re

planning to use the Sidelooker option. This type of transducer must be

mounted ahead of or beside the propeller(s). Do not use this type of

transducer for a boat with a straight-shaft inboard engine.

Use a thru-hull transducer if –

. . . your boat has a straight-shaft inboard engine. This type of transducer

is installed in a hole drilled through the hull.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Use a low-profile transducer if –

. . . you want minimum water resistance on a high-performance boat or

sailboat.The bottom of the boat must be flat, or have a deadrise angle of no

more than 10°.

Use an in-hull transducer if –

. . . you have a high-speed boat or if, for some reason, you cannot use a

transom-mount or thru-hull transducer.The hull may be no more than 1" thick.

Use a trolling motor transducer if –

. . . you want to attach the transducer to a trolling motor. (Not recom-

mended for deep-water operations.)

Use a Sidelooker transducer –

. . . for searching for fish or structure on either side of the boat. This type

of transducer is attached to the bracket of the transom-mount transducer,

or to the shaft of the trolling motor.

Assembling the Transducer Bracket

Fit together the two parts of the transducer bracket as shown in Fig. 2-2.

When the installation is complete, the parts snap together as shown.

LIKE THIS!

Attach the

two parts

NOT THIS!

Bracket is installed

upside down

Fig. 2-2

Assembling

the Transducer

Bracket

Lower the transducer

and snap in the

release clip

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 2-3

Transducer

Mounted on

Transom

Allow a clearance

of at least 10

Transducer in

released position

inches (254 mm)

10"

(254 mm)

Fig. 2-4

Transducer

Bracket,

Side View

Positioning the Transom-Mount Transducer

Begin by finding the best location for the mounting bracket. Here are the

rules:

•

If your boat has one propeller (outboard or inboard-outboard), mount

the transducer about 18” (455 mm) to the side of the centerline of the

boat. See Fig. 2-3. Choose the side that is on the downstroke of the

propeller. (This is usually the starboard side of the boat.) This will

reduce any interference caused by air bubbles.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Average transom angle–

no wedge necessary

Vertical transom –

place wedge this way

Sloping transom–

place wedge this way

to 5

For fiberglass hull – 1/8" to 1/4" (3.2 to 6 mm)

For aluminum hull – 1/4" to 3/8" (6 to 9 mm)

No!

The bow of the transducer

is above the bottom of the

transom, creating

Rivets on the hull are

creating bubbles.

Lower the transducer

a bit.

The rear of the transducer

is too high, creating

cavitation.

Fig. 2-5

Correct Mounting

Position

Insert screws 1 and 3

1/4" from the bottom of

slots, and screw 2

1/4" from the top of the

slot to allow room for

adjustment.

Correct

alignment

If screws are inserted

this way, it won’t be

possible to make the

height adjustment.

Fig. 2-6

Mounting

the Transom-

Mount

Incorrect

alignment

Transducer

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

•

If the propeller can be turned to steer the boat, allow at least 2" (50 mm)

beyond the swing radius of the propeller. This will prevent the

propeller from damaging the transducer when it is turned. After

installation, check the clearance by turning the wheel so the propeller

swings toward the transducer. There should always be a 2” (50 mm)

clearance.

•

If your boat has twin propellers (outboard or inboard-outboard), place

the transducer near the centerline of the boat.

Do not mount the transducer behind any hull fittings, intakes, or other

parts which extend from the hull. These may cause turbulence or air

bubbles.

•

The bracket has a quick-release mechanism. This may reduce

damage by allowing the transducer to flip up if it hits any debris or the

bottom. See Fig. 2-4. Allow enough clearance above the transducer

so that it can swing upward completely. This is about 10" (254 mm)

measured from the bottom of the transom.

•

If considering the Sidelooker option, look for a mounting location

where the Sidelooker array will not be blocked by the engine housing

or other mounted hardware.

If the boat will be carried on a trailer, be sure the transducer will not

hit any rollers, bunks or fittings on the trailer.

Mounting the Transom-Mount Transducer

1. On a boat with a fiberglass hull, the leading edge of the transducer

should extend 1/8" (3.2 mm) to 1/4" (6 mm) below the bottom edge of

the hull. See Fig. 2-5. On an aluminum hull, the transducer should

extend a bit more – 1/4" (6 mm) to 3/8" (9 mm). If the boat will be

operated at high speeds, the transducer may be mounted closer to

the centerline of the hull.

2. The lower surface of the transducer should tilt down toward the rear

at a slight angle (2° to 5°). The mounting bracket includes a wedge.

Depending on the angle of the transom on your boat, you may need

this wedge to get the correct angle for the bottom of the transducer.

3. Looking at the rear of the boat, be sure the bracket is vertical (perpen-

dicular to the water line).

4. Hold the bracket (and the wedge, if used) against the transom and

trace the positions of the screw slots.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Remove the bracket. See Fig. 2-6. The screws in the outer slots

should be placed about 1/4" (6 mm) up from the bottom of each slot.

The screw in the center slot should be placed 1/4” (6 mm) down from

the top. (This will allow you to adjust the bracket up or down a bit.)

Drill pilot holes 3/4" (19.1 mm) deep. Use a 9/64" (3.6 mm) drill bit.

To prevent drilling too deeply, wrap masking tape around the drill bit

about 7/8" (22 mm) from the tip. Drill in only as far as the tape

marker.

If you are attaching the bracket to a fiberglass hull, you can minimize

any surface cracking of the gel coat. Before drilling each pilot hole,

drill a shallow hole (chamfer) at each location about 1/16" (1.5 mm)

deep. Use a 1/4" (6 mm) drill bit.

6. Attach the bracket to the hull using the panhead screws with flat

washers. Before you tighten the screws, apply a good-quality marine

sealant to the pilot holes. This will protect the hull from water penetra-

tion. Do not tighten the screws completely yet.

7. Move the bracket up or down so that the leading edge of the trans-

ducer has the clearance shown in Fig. 2-5.

8. Once the bracket is in the correct position, you can tighten the

screws.

Mounting the Optional Sidelooker Transducer

1. The Sidelooker transducer allows the display unit to check the water

to either side of the boat. This is helpful when you are looking for fish

or structure near river banks, or under docks or piers.

2. The M78930 Sidelooker transducer is attached to the same mounting

bracket used with the transom-mount transducer. See Fig. 2-7.

Begin by installing the transom-mount bracket as described earlier.

3. Remove the two screws and brackets covering the paddlewheel.

4. Attach the Sidelooker transducer to the top of the transom mounting

bracket. Use the four panhead screws supplied. The fit should be

snug, but do not overtighten the screws.

5. Run the Sidelooker cable beside the depth cable for the transom-

mount transducer.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 2-7

Installing the

Sidelooker

Transducer

Installation Notes – Thru-Hull Transducer or

Low-Profile Transducer

The installation process for these two types is almost the same. Detailed

instructions for this installation will be included with the transducer. In this

section, we will note just a few important points.

1. Earlier we listed three general rules for placing transducers. All of

these rules apply when you are mounting a thru-hull or low profile

transducer. Here are some other rules for selecting the best mount-

ing location:

For planing hulls – Install in the flat planing area near the stern.

Always install forward of the propeller(s) and shaft(s).

For small displacement hulls – Install near the centerline of the hull

and 1/3 of the way forward from the stern. Always install forward of

the propeller(s) and shaft(s).

For large displacement hulls – Install near the centerline of the hull

and 1/3 of the way aft from the bow. Always install forward of the

propeller(s) and shaft(s).

For sailboats – Install forward of the leading edge of the keel, to one

side and near the centerline of the hull.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Choose a location where you can easily reach the transducer from

inside the boat. This will allow you to service the unit. Allow at least

6" (152 mm) of headroom above the transducer.

3. When choosing a mounting location, drill a small pilot hole (1/8" or 3.2

mm) from the inside of the hull. Before you drill the hole, be sure you

will be able to reach the large nut on the top of the unit, and that there

will be enough clearance for the cable. If there is a strake or other

feature on the hull, drill from the outside of the hull instead. (This

small hole can be filled easily if the mounting location is not suitable.)

4. The position of the transducer is especially critical on high speed

boats (capable of more than 20 knots). Check the locations of the

transducers on similar boats before installing the transducer in your

own boat. Choose the location which will offer the best performance.

5. If the bottom of the hull at the mounting location is flat, you can mount

the transducer directly through the hull. If the hull rises at an angle

(the “deadrise angle”) of more than 10°, you must include a mounting

block or “fairing.” The transducer must be mounted in a vertical

position. Attach the fairing block to the hull as firmly as possible. This

fairing block must be able to resist the drag of the water against the

hull, and must also be completely waterproof.

6. If the hull of the boat has a core-type hull, you will need to follow

some special mounting procedures. The core material must be

protected from any water which may leak from the inside of the boat.

(If the core material is allowed to remain wet, it may rot and weaken

the hull.)

7. When working with the transducer, support it by holding the body of

the unit. Do not hang the transducer from the cable.

8. It is very important to seal the opening around the transducer using a

high-quality marine sealant suitable for underwater use. After

installation, do not leave your boat in the water for any amount of time

without checking for leaks.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Notes – In-Hull Transducer

Detailed instructions for this installation will be included with the trans-

ducer. In this section, we will note just a few important points.

1. Choose the best mounting location:

For outboard powerboats – Install as far aft as possible

For inboard/outboard powerboats – Install close to the engine(s)

For inboard powerboats – Install forward of the propeller(s) and

shaft(s)

For sailboats – Install near the centerline of the hull and forward of

the leading edge of the keel

2. An in-hull transducer may only be installed in a fiberglass hull which is

no more than 1" (25 mm) thick. The in-hull transducer may not be

installed in wood or aluminum hulls.

3. Use the standard in-hull transducer if it will be installed in a flat part of

the hull, or a section with no more than 10° of deadrise. Use the angled

in-hull transducer if the mounting location has up to a 22° of deadrise.

4. Do not try to compensate for the angle of the hull by fairing the epoxy

adhesive on the face of the transducer.

5. Use the epoxy supplied with the in-hull transducer, or an equivalent

epoxy glue. Do not use any other type of adhesive, including silicone

or RTV adhesive.

Installation Notes – Trolling Motor Transducer

Both Downlooker and Sidelooker transducers may be installed on a

trolling motor. See Fig. 2-8.

Detailed instructions for these installations will be included with the

transducer(s). The Downlooker transducer is mounted on the horizontal

gear case of the motor. The Sidelooker transducer is attached to the

vertical support tube. These installations are simple, but it is important to

keep these points in mind:

1. Keep the Sidelooker transducer fully submerged. The transducer will

only produce an image if it is immersed in water.

2. Keep the Sidelooker transducer clear of weeds or debris.

3. When the position of the trolling motor is changed, the field of view of

the Sidelooker also changes. The Sidelooker can be aimed at interest-

ing echoes, but can also be positioned so that it is looking back at the

hull. Be aware of the position of the Sidelooker transducer.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 2-8

Installing the

Sidelooker

Transducer on a

Trolling Motor

Mounting the Display Unit – Standard Mount

You may mount the display unit on any flat surface using the bracket

supplied. See Fig. 2-9. (There is also an optional kit which allows you to

flush-mount the display in a flat panel or dashboard). Follow these

instructions if you are using the standard mounting bracket:

1. The “LCD” type display used on this unit is easier to see from certain

angles. Before selecting a permanent mounting location, make

temporary power connections and turn on the unit. This will allow you

to test the visibility of the display from several different angles.

2. Remove the display unit from the bracket by pressing on the large

button in the center of the bracket. See Fig. 2-9.

3. Mount the base of the bracket using the supplied screws.

4. Slide the display unit back into the bracket.

5. Adjust the display unit for the best viewing angle. You can turn the

display from side to side, and tilt it up or down.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Raymarine

To release the

display from

the base,

press on the

right and left

sides until you

hear the clicks.

Slide the

The angle of

the display

can be changed.

265 ^E

265

display out of

the bracket.

The display can

be turned from

side to side.

Fig. 2-9

Installation

on Bracket

Dismounting the Display Unit

See Fig. 2-9. To release the display from the bracket, press and hold

down the left and right sides. You will hear an audible “click,” and the

bracket will slide out.

Mounting the Display Unit – Flush Mount

In order to do this installation, you will need the optional flush mounting kit

(part no. M78931). See Fig. 2-11.

1. Select a mounting location on the dashboard or control panel.

Choose a clear, flat area at least 6" x 6" (152 mm x 152 mm). Be sure

you will also have at least 6" (152 mm) of clearance behind the area

where the display unit will be mounted. It is a good idea to drill a

small pilot hole in the center of the mounting area. Be sure there are

no hidden electrical wires or other items behind the point where you

plan to mount the display unit.

2. A mounting template is supplied with the flush mounting kit. Tape this

over the selected location on the panel and trace around the edges.

3. Make the cutout for the display. Drill a series of 1/2" (13 mm) holes at

the points shown around the edges of the cutout area.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Countersink

3/8" (10 mm)

2-25/32"

(70 mm)

Hole 3/16" (5 mm)

2-21/32"

(67 mm)

2-23/32"

(69 mm)

1-13/32"

(36 mm)

5-7/32" (133 mm)

63/64"

(25 mm)

6-3/4"

(172 mm)

5-9/32"

(134 mm)

1-3/4"

(44 mm)

4-9/32"

(109 mm)

3-29/32"(99 mm)

4-7/32"(107 mm)

Fig. 2-10

Dimensions

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Gasket

Mounting hole

cut according to

template

Screw holes

Fasten with

threaded studs

and wing nuts

Fig. 2-11

Flush-mount

Installation

4. Drill the two small holes for the threaded studs as shown on the

mounting template. Use a 7/32" (5.5 mm) drill bit.

5. Remove the template and draw straight lines between the 1/2" holes.

Cut along each of the lines with a small saw.

Raymarine

PAGE

FIS

L265

To pry up the cap

insert a small

screwdriver here

Fig. 2-12

Disassembling

from Bracket

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Separate the display unit from the mounting bracket. (See Fig. 2-12.)

Press the large button in the center of the bracket to separate the

bracket arms. The display unit is attached to the arms by two screws.

Each screw is covered by a cap. Locate the small slot beside each

cap and pry upward using a small screwdriver. Remove the caps,

then the two screws and the two wave washers. Save these parts in

case you ever want to use the mounting bracket.

7. Screw the threaded studs into the holes on the rear of the display

unit.

8. Set the display unit into place to be sure that it will fit correctly.

Thread the wing-nuts onto the threaded studs to hold the display unit

in place temporarily.

9. Install the DC power wiring as described later in this section. Finally,

finish the installation. Hold the gasket in place around the opening.

Fit the display unit into the cutout. From the rear, screw the thumb-

screws securely onto the threaded studs to hold the unit in place.

Installing the Transducer Cable

A 20 foot length of cable, with the connector attached, is supplied with the

transducer. During the installation, do not cut the transducer cable or

remove the connector. Do not try to shorten or splice the cable. The

transducer cable includes several wires, along with shielding and

insulation. If the cable is cut, it cannot be repaired. (Cutting the cable

will also void the warranty.) During installation, if you need to drill any

holes for the cable, they must be large enough to accept the connector.

This will allow you to make the installation without cutting the wire.

1. Route the cable up and over the top edge of the transom. See Fig. 2-

13. Secure the cable using cable clamps. (These clamps are

available from your local marine equipment supplier.)

If you do not want to expose the cable on the deck, you may drill a

new hole (3/4" or 19 mm) through the transom for the cable. (Re-

member – this hole must be large enough to accept the cable with the

connector attached. Do not cut the cable!) To seal the opening, use

a feed-thru cap where the cable passes through the transom.

2. Run the cable through the interior of the boat. If the transducer cable

runs near another electrical wire, it may pick up electrical interference

or “noise.” To reduce this, try to keep the transducer cable separated

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

as far as possible from all other wires. This is especially important

with wiring for the boat’s ignition, alternator, or tachometer. Also try to

keep the transducer cable away from the antenna and power cables

for VHF or FM radios. It is also helpful to keep the transducer cable

away from the FishFinder power cable. If it is necessary to run the

transducer cable across any wires, make the crossing at a right angle.

3. Be careful not to tear the cable jacket when passing it through

bulkheads and other parts of your boat. Secure the cables in place

using tywraps or lacing twine. Coil the extra cable and tie it out of the

way.

4. If the 20 foot (6 m) transducer cable is not long enough, a 15 foot

(4.6 m) extension cable is available from your Raymarine dealer (part

no. M99-140). When you attach the extension cable, be sure that the

connections are tight and watertight. Use Dow Corning DC-4 or an

equivalent sealing compound to protect the connector assemblies.

Note: To extend both depth and Sidelooker cables, use the M99-139

extension cable.

5. At the rear of the display unit, plug in the transducer cable using the

keyed connector.

Cable feed-thru

cap

Cable clamp

1" (25 mm)

Hull projections

Fiberglass: 1/4" (6mm)

Aluminum: 1/2" (13 mm)

Fig. 2-13

Installing Cable

on Transom

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the Transducer Cable – Sidelooker Option

1. If the installation includes the optional Sidelooker transducer, there

will be two transducer cables. See Fig. 2-14. The cable from the

Sidelooker includes a “Y” connector.

2. Plug the cable from the depth transducer into the open end of the “Y”

connector.

If extending

this cable only,

use the M99-140

cable.

If adding an

extension here,

use the M99-139

cable.

Sidelooker

Fig. 2-14

Cable for

Sidelooker

transducer

Depth

transducer

Transducer

Making the DC Power Connections

1. The display unit is designed for use on boats with 12V DC power

systems. (The unit can operate as long as the DC voltage is between

11.0 and 16V DC.) The display unit can be wired to a negative-

ground system, or both the negative and positive supply lines may be

“floating” above ground. This unit is not intended for use on boats

with positive ground.

2. The 5-foot power cable (1.5 m) supplied with the display unit should

reach the source of DC power. On a small boat, connect the power

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

leads directly to the main battery isolation switch or breaker. On a

larger boat, route the power leads to the DC power distribution panel.

3. It is very important that you connect the power leads correctly.

See Fig. 2-15. At the power source, connect the red wire to the

positive terminal (+), and the black wire to the negative terminal

(-). The negative terminal may also be called “ground” or “earth.”

(The display unit is internally protected if you accidentally reverse

the polarity of the power wires.)

4. Attach the red or positive wire to a 5 amp circuit breaker. If the unit is

connected directly to the boat’s battery, include a 2 amp in-line fuse.

(In-line fuses are available at most marine supply stores.)

5. To prevent any interference or electrical noise, separate the

FishFinder power wiring as much as possible from other devices.

Avoid running the FishFinder power wires near the power wiring for

any radar, radio, or Loran-C units. If possible, wire the FishFinder

power wires to a separate circuit breaker.

6. If you need to extend the power wiring by more than 10 feet, use a

larger wire size. This will allow the wires to deliver the correct voltage

in spite of the longer wire distance. For runs of 20 to 35 feet, use #14

AWG.

DC 12V

connector

to battery

T/D

connector

to transducer

RED

BLACK

DC 12V

Fig. 2-15

DC Power

Connections

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

If you extend the power wiring, be sure all electrical connections are

solid and durable. Soldering is the best way to make these connec-

tions. Insulate all connections using heat-shrink tubing or electrical

tape. You may also use crimp connectors or a terminal strip, but be

sure to use good-quality marine-grade parts.

7. At the rear of the display unit, plug in the power wires using the keyed

connector.

PWR

8. When you press the

button, the display unit should turn on. If

the unit will not turn on and you suspect that you may have reversed the

power connections, check the DC power lines all the way back to the

battery. If the polarity is not correct, reconnect the leads properly and

try again.

Final note: After you finish the installation, please remember to fill out the

Warranty Card included with this manual.

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

3 – Operating Instructions

In this section of the manual, we will explain how to operate the unit.

(Setup instructions are included in the next section.) Below is a drawing

of the display unit.

Power button

Raymarine

PWR

Display area

Page control

pad

PAGE

Set-up button

SETUP

Clear button

CLEAR

FISHFINDER

L265

Fig. 3-1

Display

Panel

Controls on Display Unit

The FishFinder is designed to be easy to use while the boat is moving.

You can steady your hand by gripping the right side of the display with the

fingers of your right hand. This will allow you to use your right thumb to

press the buttons on the display.

Notice that some of the buttons can be used in two ways. They do one job

during a normal display, and a different job when you are setting up the

SETUP

CLEAR

PWR

unit. In this section, we will use the symbols

indicate the power, setup and clear buttons.

and

PWR

This button turns the power on and off.

To turn on the power – Press once to turn the power on.

PWR

To enter the Lamp/Contrast menu – Press

quickly at

any time to enter the “Lamp/Contrast” menu.

To turn off the power – If you press and hold the button,

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

the display will say “Powering Off.” If you hold the button

for more than 3 seconds, the display unit will switch off.

Page control

pad

Up and down arrows – ( and

)

During setup – Use these controls to call up a choice or

move to the next line on a menu.

If the Zoom display is turned on – If the manual zoom

feature is turned on, these will move the zoom display up or

down.

Left and right arrows – (< and >)

During normal display – Use these buttons to go to the

next display.

During setup – Use these arrows to make a choice within

a line on the menu.

SETUP

To enter the Setup Menu – Press

at any time.

To go to the System Setup display – Press this button

twice.

CLEAR

During normal display – When an alarm is triggered, use

CLR

to turn off the buzzer. (The alarm will continue).

CLEAR

During setup – Once you make a change, press

save the change and go back to the normal display.

Turning the Power On and Off

PWR

Press the

button once to turn on the power. For a few seconds, the

Lamp/Contrast Menu will appear and the panel light will flash on and off.

The light will help you to set up the display in the dark.

PWR

To turn the power off, press and hold the

seconds.

button for more than 3

Setup Memory

When you first turn on the power, the unit will be prepared to operate

using a number of preset values. These “default” values are stored in the

unit at the factory. (The default values are listed in Section 4.)

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

This unit has a memory for some of the settings – range, sensitivity, zoom,

and frequency. (We will explain these in a moment.) When you turn off

the power, any changes you make to these settings will be saved.You can

return all of the settings to the factory default values, and reset the trip log

PWR

CLEAR

to zero. To reset the unit, turn it on by pressing the

at the same time.

and

buttons

Lamp/Contrast Menu

Turn lamp

on or off

Adjust

contrast

Fig. 3-2

Lamp/Contrast

PWR

Press

The Lamp/Contrast Menu appears when you first press

PWR

the

button and turn on the power. (You will be able to

see part of the main FishFinder display behind the Lamp/

Contrast menu.)

PWR

You can press the

button a second time to exit from

the Lamp/Contrast menu and go directly to the FishFinder

mode. (If you do not make any changes to the settings

within 7 seconds, the unit automatically exits from the

Lamp/Contrast menu anyway.)

You can also enter the Lamp/Contrast menu from any of

PWR

the other displays by pressing the

moment.

button for a

Turn on lamp The display unit includes a backlight which allows you to

read it at night. If you want to turn on the lamp, use either

the < or > arrows on the Page control pad.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 3-3

Selecting

Display

Pages

Lamp/Contrast menu

FishFinder page

A-Scope page

Zoom page

Sidelooker page

Note:This will appear

only if the Sidelooker

feature is turned on.

Digital page

Return to

FishFinder

page

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjust contrast You can also adjust the “contrast” of the display. This is a

measure of how light or dark the display appears. Use

the

control to move from the line for “Lamp On/Off” to

the line for “Contrast.” Use the < or > controls to adjust

the contrast. (The FishFinder unit has a feature which

adjusts the contrast automatically to compensate for

changes in air temperature.)

Save settings When the settings on this display are correct, press the

CLEAR

button to save the settings and go to the FishFinder

page.

Operating Pages

This unit has 5 “pages” or normal displays. These can be used to show

different kinds of information. Here is a list of the modes:

Mode

FishFinder page

Function

Standard operating mode, good

general coverage of bottom.

See page

page 28

Zoom page

Magnified view of smaller section

of bottom.

page 37

A-Scope page

Digital page

Detailed view of area under

transducer.

page 39

page 41

Numerical display of depth

Sidelooker page

View of either side of centerline of boat,

(using optional

(used only with Sidelooker transducer) page 42

Sidelooker transducer)

You can step from one of these pages or displays to another using the

< and > arrows on the Page control pad. See Fig. 3-3.

There are two other kinds of displays you can see here:

•

The system includes several setup displays which can be used to

change some of the controls used by the unit. See Section 4.

When the Simulator Mode is switched on, the unit generates its own

display without receiving signals from the transducer. This mode is

used for sales and training.

•

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

FishFinder Page

Auto

Auto sensitivity on

zoom on

Auto

range on

Auto

features on

Fish symbol

Transducer

frequency

Boat symbol

Water surface

Depth markers

Fish depth

Bottom

indication

Fish symbol

Range

Buzzer symbol

Fish alarm set

Bottom depth

Deep alarm set

Shallow alarm set

Fig. 3-4

FishFinder

Page

A moment after you first turn on the display unit, the Lamp/Contrast menu

disappears. The unit then automatically switches to the FishFinder page.

Figure 3-4 shows a typical display. (The FishFinder page is also called the

“chart” or “bottom graph” display.) As time passes, this display scrolls from

right to left. The scrolling image becomes a record of the echoes and the

bottom seen by the FishFinder as your boat moves.

The images at the right side of the display show the most recent echoes.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Some of these echoes indicate fish, and others show the bottom. As new

echoes are received, the FishFinder “draws” a graph of the bottom. The

bottom graph helps you to tell whether the bottom is rising or falling. It

also allows you to identify the shape or “structure” of the bottom. This

can indicate a reef or shipwreck.

Notice that the scrolling speed of the display does not necessarily match

the speed of the boat. The scrolling speed of the display is called the

“chart speed.” You can adjust this using the “System Setup Display.” (See

Section 4.)

Many of the items on this display appear in the other modes. Since you are

likely to use the FishFinder page most often, we will explain all of these

items here.

Top of display

Auto features on

(AUTO)

If any of the automatic features are turned on, the “Auto”

indication will appear here. (These include the automatic

range, auto sensitivity, and auto zoom features.)

Auto range on (R)

The “range” is the maximum depth the unit is set to

measure. When the auto range feature is on, the

FishFinder chooses the correct range setting automatically.

Transducer frequency

The transducer can use two frequencies - 50 kHz for wide

coverage, or 200 kHz for a detailed view. You can also set

the unit to use both frequencies at the same time (“dual

frequency”). (For more on this, see “Choosing the Fre-

quency.”)

Auto sensitivity on (S)

The “sensitivity” controls the ability of the unit to tell the

difference between echoes of different strengths. A higher

sensitivity setting makes it easier to see smaller fish, but

also may pick up background noise. When auto sensitivity

is on, the FishFinder chooses the correct sensitivity setting

automatically.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto zoom on (Z)

The “zoom” can be used to magnify the image from a small

section of the water below the boat. (This is used with the

Zoom display, which we will describe in a moment.) When

the auto zoom feature is on, the FishFinder automatically

moves the zoom window up or down to track the bottom.

Fish symbol on

When the FishFinder sees a fish, it can show this by

displaying a fish symbol. When the fish symbol feature is

turned off, the FishFinder indicates a fish as an arch-

shaped line on the display. For more information, see the

section on “Fish Indications.”

Boat symbol This symbol is always turned on. It indicates that the new

information appears at the right edge of the display, and the

older information moves toward the left.

Center of display

Water surface This symbol (“0”) shows the depth indicated by the top of

the display. Usually, this is the level of the surface of the

water. (If the Zoom feature is turned on, this will show the

depth of the top of the zoom area.) The depth is shown

using the same units as the rest of the display. This could

be feet (FT), fathoms (FA), or meters (M), depending on the

setting you make in the System Setup display.

Depth markers

These markers show depths between the surface and the

full depth range. In this example, the unit is set for a depth

range of 100 feet. This means that each of the depth

markers shows an interval of 20 feet.

Fish symbol This indicates that the FishFinder sees a fish. Generally,

the larger the fish symbol appears, the larger the fish. (The

size of the fish symbol actually depends on a number of

factors. See the section on “Fish Indications.”)

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

If the fish is detected using the narrow 200 kHz beam, the

display will show a filled-in symbol. If the fish is detected by

the wide 50 kHz beam, the display will use a hollow symbol.

(For more on this, see “Choosing the Frequency.”)

Fish depth

This indicates the depth of the fish shown by the fish

symbol. This number will be shown using the same depth

units (feet, fathoms, or meters) you have selected on the

System Setup display. The fish depth indicator is turned off

when the fish symbol function is off.

Bottom of display

Bottom indication

This shows the bottom of the lake or sea. You can com-

pare this to the range depth shown in the lower right-hand

corner. (In this example, the checkered pattern shows the

unit is getting a strong echo return from the bottom. See

the information on the White Line feature in the Setup

Instructions.)

Range

The “range” is the maximum depth the unit is set to

measure. In this example, this is 100 feet. You can set the

range manually, or the FishFinder can do it automatically.

Bottom depth This is the depth of the bottom shown on the display. You

can select FT (feet), FA (fathoms), or M (meters) using the

System Setup display. If the FishFinder can’t tell how deep

the water is, the last known depth flashes on the display.

This will continue until the unit can see the bottom again.

Buzzer symbol

This symbol shows whether any of the alarms will use the

buzzer. There are three kinds of alarms: shallow, deep, and

fish. If one of these alarms is set, it will always present a

flashing symbol on the display. The Buzzer symbol shows

whether the alarms will also use the buzzer.

If the Buzzer setting in the System Setup display is on

(indicating that the buzzer is enabled for all of the alarms),

this symbol will appear filled.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

If the Buzzer setting is off (indicating that the buzzer is

disabled for all of the alarms), this symbol will be open.

Shallow alarm set

You can set an alarm to go off if the boat moves into water

which is shallower than a certain depth. If you set this type

of alarm, the “S” indicator will appear on the display. If the

alarm is triggered, the “S” symbol will flash. If the buzzer

has been turned on (in the System Setup display), the

CLEAR

buzzer will also sound. To stop the buzzer, press the

button. The “S” symbol will continue to flash until you move

into deeper water.

Deep alarm set

You can set a different alarm to go off if the boat moves into

water which is deeper than a certain depth. When this

alarm is set, the “D” symbol will appear. If the alarm is

triggered, the “D” symbol will flash. If the buzzer has been

turned on (in the System Setup display), the buzzer will

CLEAR

also sound. To stop the buzzer, press the

button. The

“D” symbol will continue to flash until you move into

shallower water.

Fish alarm set

The FishFinder also has an alarm which will sound when-

ever it detects a fish. When this alarm is set, the fish

symbol appears at the bottom of the display. If the alarm is

triggered and the buzzer has been turned on (in the System

Setup display), the buzzer will sound for a moment.

Before we explain the other pages, there are some general things you

should know about the operation of the FishFinder.

Choosing a Frequency

We said that the FishFinder uses sound waves to “see” through the water

under the boat. The “frequency” is a measure of how fast the sound

waves change or “vibrate.” The FishFinder uses sound waves with two

different frequencies – 50 kHz and 200 kHz. Raymarine uses these two

frequencies because each is better for a particular purpose.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

50 kHz frequency

•

Scans a wide area

Penetrates water well, good for deep water

200 kHz frequency

•

Scans a narrower area, but produces a more detailed view

Good for seeing fish near the bottom or fish close together

Better for use in very shallow water

“Dual” frequency (both 50 kHz and 200 kHz at once)

•

Has the advantages of both frequencies

Good depth penetration

Good detail in display

Using the “Dual 50 kHz” setting, the display is produced using the

signal from the 50 kHz beam, with additional information from the 200

kHz beam.

•

Using the “Dual 200 kHz” setting, the display is produced using the

signal from the 200 kHz beam, with additional information from the 50

kHz beam.

If you are using one of the dual frequency settings, you can get some

useful information from the fish symbols. If the fish is spotted by the

narrow 200 kHz beam, the fish symbol will be black or filled-in. If a fish is

detected by the wide 50 kHz beam, the symbol will be hollow.

Fish Indications

Even using advanced sonar technology, it is sometimes hard to detect a

fish in the water. The body of a fish is just a little more dense than the

surrounding water. There is really nothing very solid for the sound waves

to bounce off of. The FishFinder L265 is very good at telling the difference

between a fish and the surrounding water. In fact, Raymarine is the leader

in this technology.

When the FishFinder finds a fish, it can be indicated by a fish symbol on

the display. In general, a larger symbol means a larger fish. This rule is

not always true, though. Let’s say that there are two fish of the same size:

one is close to the surface, and the other is near the bottom. The fish

which is close to the surface will have a larger symbol. This is because

the fish which is closer returns more of the sound waves back to the

FishFinder.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Actually, the sound waves are usually reflected by the air sac near the

center of the fish, and not by the body of the fish. The size of this air sac

is different for different kinds of fish. This can also affect the size of the

fish symbols on the display. A fish with a large air sac will produce a large

fish symbol, while a fish with a small sac will produce a small symbol.

The symbol also indicates which of the two frequencies was used to locate

the fish. If the fish was spotted by the wide 50 kHz beam, the symbol will

appear to be hollow. If the fish was detected by the narrow 200 kHz

beam, the symbol will be solid.

If the fish symbol feature is turned off, the FishFinder indicates fish in a

different way. See Fig. 3-5. An arch-shaped mark on the display usually

indicates a fish. Again, a larger arch usually indicates a larger fish.

Several arches together show a school of fish.

The return from a fish will have a different appearance, depending on the

frequency used. If a fish is spotted by the wide 50 kHZ beam, the arch will

An arch-shaped image indicates a fish.

The same fish appears differently

when shown by the 50 kHz or 200 kHz

transducer beams.

50 kHz

200 kHz

This indicates a group of small fish.

This shows a fish detected in

sidelooker mode.

A shallow arch or horizontal line is

generated when the boat is moving

slowly or stopped.

When the boat is moving very fast,

a fish appears as a single vertical line.

Fig. 3-5

Fish

Indications

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

be broad. When using the narrower 200 kHz beam, the same fish will

produce a narrower arch.

The shape of the arch is also affected by the speed of the boat. If you are

moving slowly, the arches tend to be longer. If the boat is moving more

quickly, the arches are short and peaked. If the boat is moving very fast, a

fish may be indicated by a single vertical line.

Bottom Indications

The bottom usually produces a strong echo, so it is easy for the

FishFinder to see a lot of detail. The FishFinder can indicate many

different kinds of bottom conditions. See Fig. 3-6. A hard bottom appears

as a thin line. A softer bottom or a bottom covered with seaweed will

produce a wide line, as the sound waves reflect from different layers of the

bottom. An uneven bottom which is covered with rocks or coral produces

a complex display like that shown in the last part of the Figure. The

bottom image is irregular, with long “tails” pointing upward. A wreck

produces a similar image.

When the White Line feature is turned on, the unit can display even more

information about the bottom. In Fig. 3-4, the FishFinder is getting a good

Hard

(Sand)

Soft

Rocks

(Mud)

Fig. 3-6

Bottom

Conditions

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

echo from the bottom, so the upper layer of the bottom is shown in a

checkerboard pattern.

Notice that the lower layer of the bottom is shown as a solid display. This

indicates a weaker echo. Sometimes this means that the upper layer of

the bottom is soft. Some of the sound waves may reach through this

layer, and may be reflected by a more solid layer below. It is also possible

that the sound waves are making two complete trips - hitting the bottom,

bouncing off of the bottom of the boat, then reflecting off the bottom again.

This can happen if the water is shallow, the bottom is hard, or the sensitiv-

ity is set to a high value.

Performance Modes

This unit has two “performance” modes which can be used to add to

the standard FishFinder Page. These are the Zoom and the A-Scope

Modes. Each presents the raw information from the transducers in a

special way. To display one of these modes, press the Page key on

the unit. See Fig. 3-3.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Zoom Page

Press

Zoom display

(magnified)

Normal

display

Top of zoom

area

Line indicates

zoom area

Bottom of

zoom area

Zoom

magnification

Fig. 3-7

Zoom Page

The Zoom page gives you a way of enlarging or magnifying a part of the

display area. See Fig. 3-7. (The “zoomed” display is actually larger only

in the vertical direction.) The right side of the display shows the same

information as the FishFinder page. The left side shows the magnified

view. In each case, the new information appears at the right edge of the

display, and moves to the left.

Many of the items on the Zoom page are the same as those on the

FishFinder page. There are a few new items.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Zoom magnification

This indicates the amount of “zoom” or magnification. You

always set the amount of zoom manually, using one of the

functions on the Setup display. You can choose an x2 view

(double the normal display size), x4, x6 or x8 in the series

of setup screens. See Section 4. You must also select the

area or “window” of the water you want to zoom. See the

next item.

Zoom area

When you turn on the zoom feature, it can only enlarge a

part of the FishFinder display. You must decide which part

you want to enlarge. As we said, the right side of the

display shows the normal FishFinder display. The vertical

line at the right edge of this display shows the area or

“window” of the water being enlarged.

When the FishFinder is set for auto zoom, it will choose the

zoom area automatically. The unit always chooses an area

of the water which includes the bottom. The unit then

moves this area up or down to keep the bottom in the

picture. The auto zoom feature is great for bottom fishing.

You may also set the zoom area manually. In the series of

setup screens, select manual zoom. (See Section 4.)

Once you are back to the zoom display, you can move the

zoom area up or down (using the and

arrows on the

Page control pad) to enlarge any selected “window.”

To move to the next display, press the > arrow on the Page control pad.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

A-Scope (Bottom Coverage) Page

Press

A-Scope

display

Normal

display

A-Scope image

(real time image)

Fish

indication

Bottom

coverage

Fig. 3-8

A-Scope

Page

On the FishFinder display the bottom graph is “drawn” after the FishFinder

receives several echoes. This has the effect of showing a record of the

bottom contour. The A-scope displays raw sonar data directly from the

transducer beam. This gives you a “real time” image of fish and bottom

structure directly below the transducer. This function is very useful in

showing the strength of the echo returned from a fish. Stronger fish

echoes on the A-scope display will appear wider; weaker echoes appear

as narrow bands closer to the horizontal center of the A-scope image.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

The left section of the A-Scope display shows a section of the normal

FishFinder display. All of the features are the same. The right section

shows the A-Scope image.

A-Scope image

This shows the beam of sound waves extending down from

the boat, and spreading as it moves through the water. Any

fish or objects which are positioned under the boat will

appear on the display. This is a “real time” display, so you

can see the fish symbols moving as the fish swim under the

boat.

Bottom coverage

This shows the diameter of the beam of sound waves

where it meets the bottom. This dimension will be shown

using the same units as the rest of the display – feet (FT),

fathoms (FA), or meters (M). If the unit is set at 200kHz

single frequency, the bottom coverage display will reflect

the narrow (16°) beam of the 200kHz frequency setting. All

other frequency selections (200kHz dual, 50kHz dual, and

50kHz single) use the wider (65°) beam for the bottom

coverage display.

To move to the next page, press the > arrow on the Page control pad.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Page

Press

Depth

Fig. 3-9

Digital

Page

Alarms

The Digital page presents the depth in large numbers on the display. See

Fig. 3-9. This display is useful when you are traveling, but not looking for

fish or checking the appearance of the bottom.

Depth

The Digital display reports the depth of the bottom.

Alarms

Notice that the alarm indications still appear at the bottom

of the display.

To move to the next display, press the > arrow on the Page control pad.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Sidelooker Page

Press

This feature will only work if an optional Sidelooker transducer has

been installed, and if the Sidelooker feature has been turned on in the

System Setup Menu. The Sidelooker feature is very helpful for certain

kinds of fishing. It allows you to check for underwater structure along

the sides of a stream or river, under the edge of a bank or pier, or into

stumps or weed beds.

Transducer mounted

on trolling motor

Rock

31° beam

Fish

Boat

Rock

Fish

Sidelooker

transducer

Fig. 3-10

Sidelooker

Feature

11° beam aimed

down at 4° angle

The optional Sidelooker transducer transmits two acoustic beams—one to

the port side of the boat, and one to the starboard. These are displayed

on the left and right halves of the Sidelooker Page. See Fig. 3-10.

Once the Sidelooker feature has been turned on, you can reach the

Sidelooker page easily. Press the < or > buttons on the Page Control

Pad until the Sidelooker Page appears. The unit will present a display

similar to Fig. 3-11.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Boat symbol

Side range

Fish echo mark

Bottom/shore

indication

Centerline

Speed

Log/distance

Water temperature

Depth below boat

Fig. 3-11

Sidelooker

Page

The Sidelooker Page, like the FishFinder Page, displays a graph or chart.

The scrolling vertical dashed line represents the centerline of the boat. As

new Sidelooker echoes are received, the new information appears at the

top of the display, and older information moves towards the bottom. There

is no relationship between the chart speed of the FishFinder and the

speed of the boat. (The speed at which the display moves is set by the

entry for “chart speed” in the Setup Menu.)

When the Fish Symbol feature is turned off, any fish detected will appear

as vertical marks. These may be slightly arched towards the center of the

display. The unit can also be set to display fish symbols, but the normal

fish marks are usually more helpful. The Sidelooker transducer transmits

at the 200 kHz frequency. If the unit spots any fish while the Fish Symbol

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

feature is on, they will be indicated by solid fish symbols. (You can turn the

Fish Symbol feature on or off from the System Setup Menu. See Section 4.)

Underwater objects such as submerged tree stumps or rocks can also be

detected by the Sidelooker transducer. These objects usually appear as

thicker vertical targets. The Sidelooker sounding beam is transmitted very

close to the surface of the water. In rough or choppy water this turbulence

may appear on the Sidelooker display as “noise” or “clutter.” The Side-

looker will also display noise or clutter when your boat travels at high

speeds or in very shallow water. For best results, use the Sidelooker at

idle or slow trolling speeds.

Here are the special items on this display:

Boat symbol This is pointing forward on the screen to indicate that, on

the Sidelooker Page, the view is from above, as seen from

a bird’s-eye. The boat symbol appears at the top center of

the Sidelooker View.

Dashed

vertical line The scrolling vertical line is drawn under, or behind, the

boat symbol to indicate the division between the information

produced by the left and the right sidelooker transducer

elements.

Side range

This is the maximum distance the unit will be able to see

using the current range setting. Remember that the sound

waves move out at a shallow angle, so this distance is

measured sideways. See Fig. 3-10. The units used here

are chosen using the entry for Depth Units in the System

Setup Menu. If you have selected feet (FT) or fathoms

(FA), the distance shown here will be measured in feet. If

you have selected meters (M), the distance shown here will

be in meters.

Fish echo mark

A line or arch-shaped mark shows that the unit has detected

a fish. In general, a larger mark indicates a larger fish. If the

fish symbols are turned on, the unit will indicate fish using

symbols instead. A number beside each symbol shows the

distance from the boat to the fish. Remember that this

distance is measured sideways. See Fig. 3-10.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

The units used here are chosen using the entry for Depth

Units in the System Setup Menu. If you have selected feet

(FT) or fathoms (FA), the distance shown here will be

measured in feet. If you have selected meters (M), the

distance shown here will be in meters.

Bottom/Shore

Indication

This indicates the area where the transducer beam is start-

ing to see the bottom, shore, or some other object. Again,

remember that the beam is looking sideways, so this could

really represent the bank of a stream or structure under a

dock or pier.

Depth

This is the depth directly below the boat. Even when the

Sidelooker feature is turned on, the downward-looking

transducer is still used to measure the depth.

The Sidelooker feature has settings for Range and Sensitivity which are

separate from the Range and Sensitivity settings used for the standard

FishFinder Page. See Section 4 for details.

Operating Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – Setup Instructions

Press

The Setup Menu

Press the Setup button to enter the Setup Menu. To move from one

display to another, press the and arrows on the Page control pad. To

CLEAR

return to the normal display, press

. See Fig. 4-1. This means that

you can reach these displays quickly, make a change, then return to the

normal display quickly.

Fig. 4-1

Moving

Through

the Setup

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Range Setting

Fig. 4-2

Range

Settings

SETUP

If you press

once, the first menu item allows you to set the range.

See Fig. 4-2. The range sets the maximum depth the unit will be able to

see. Use the < and > arrows on the Page control pad to select Auto or

SETUP

Manual range. (If you press

while you are looking at the Sidelooker

display, the unit will allow you to set the range for the Sidelooker feature.

See the end of this section.)

Auto range

The FishFinder can be set to select the range by itself,

automatically. The unit chooses the shallowest range which

will still include the bottom in the display. If the bottom rises

or falls, the FishFinder will adjust the range to keep the

bottom in the display.

Manual range You can also set the range yourself. (However, if the

bottom rises or falls, the FishFinder will not adjust for this.)

As soon as you select Manual, the cursor will jump down a

line so you can choose the range you want. Use the < and

> arrows on the Page control pad to make a selection.

Here are the choices:

Possible Range Settings (Auto or Manual)

In feet: 5, 10, 20, 30, 50, 80, 100, 150, 250, 400, 600, 1000, 1500, 2000

In fathoms: 2, 3, 5, 10, 15, 20, 25, 30, 50, 80, 100, 150, 200, 350

In meters: 2, 5, 10, 15, 20, 25, 30, 50, 80, 120, 200, 300, 500, 650

CLEAR

If you are done with your setup changes, press the

button to go back

to the normal display. To select the next menu item, press the arrow on

the Page control pad.

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Sensitivity Setting

Fig. 4-3

Sensitivity

Setting

The sensitivity adjusts the ability of the unit to tell the differences between

echoes of different strengths. In general, the sensitivity should be as high

as possible, to detect the fish and show the detail on the bottom. How-

ever, if the sensitivity is too high, the unit will begin to see bubbles in the

water, debris, and other “background noise.” Use a higher sensitivity

setting for deeper water, and a lower setting for shallower water.

If you adjust the sensitivity while you are looking at the Sidelooker display,

this will affect the sensitivity for the Sidelooker feature only.

From the menu item for the range setting, press the

arrow on the Page

control pad. The next menu item will allow you to set the sensitivity. See

Fig. 4-3. Use the < and > arrows on the Page control pad to select Auto or

Manual sensitivity.

Auto sensitivity

The FishFinder can be set to select the sensitivity by itself,

automatically. The unit chooses the sensitivity setting

which will detect fish, but will also show a minimum of

background noise. If the amount of background noise

changes (due to changing depth or water conditions), the

FishFinder will change the sensitivity to adjust. (You can

adjust the sensitivity of the unit while it is using Auto

sensitivity. Once Auto sensitivity is selected, use

the arrow on the Page control pad to go to the next line,

then use the < and > arrows on the Page control pad to

fine-tune the setting. When the FishFinder is turned off,

then on again, the Auto sensitivity setting will return to the

normal or default setting.)

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual sensitivity

You can also set the sensitivity manually. If the amount of

background noise changes, the FishFinder will not adjust

for this. If you choose Manual sensitivity, press the arrow

on the Page control pad to go to the next line. Use the < and

> arrows on the Page control pad to move the dark bar on

the display. Making the bar longer increases the sensitivity.

CLEAR

If you are done with your setup changes, press the

button to go back

arrow on

to the normal display. To select the next menu item, press the

the Page control pad.

Chart Speed Setting

Most of the displays on the FishFinder show a record of the signals the

unit has received. The new information appears at the right (or top) edge

of the display. The older information moves toward the left (or bottom) of

the display. The chart speed adjustment sets the speed at which the

display moves. (Notice that the scrolling speed of the display is not

related to the speed of the boat over the bottom. The speed of the display

is controlled only by the chart speed setting.)

Figure 4-4 shows how the chart speed setting affects the display. In both

cases, the unit is showing the same section of the bottom. Using a faster

chart speed, the display has more space on the display to show this

section, so it can include more detail. Using a slower chart speed, this

Section of bottom shown

at higher chart speed -

Display shows

more detail

Same section shown at

slower chart speed -

Fig. 4-4

Changing the

Chart Speed

Setting

Display shows

longer "history"

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

same information is displayed in a smaller horizontal space.

A faster chart speed setting shows more detail on the bottom. You will

probably want to use a faster setting when you are looking for fish.

A slower chart speed setting shows a longer record of the bottom you

pass over. Any fish detected will stay on the display longer.

From the display for the sensitivity setting, press the

arrow on the Page

control pad. The next menu item will allow you to set the chart speed.

See Fig. 4-5.

Chart speed This adjusts the speed at which the information moves

across the display. Use the < and > arrows on the Page

control pad to change the chart speed. Making the bar

longer increases the chart speed. If you move the bar all of

the way to the left, the FishFinder will “freeze” and hold the

current display. (The depth indicator will continue to

update.)

CLEAR

If you are done with your setup changes, press the

button to go back

arrow on

to the normal display. To select the next menu item, press the

the Page control pad.

Fig. 4-5

Chart Speed

Setting

Zoom Setting

The “Zoom” feature allows you to enlarge or magnify a section of the

normal display. This lets you see a “window” of the echo sounder view in

detail. The Zoom window may be set for four different levels of magnifica-

tion.You can choose settings for x2, x4, x6 or x8 magnification.

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 4-6

Zoom Settings

Zoom

magnification Press the > arrow on the Page control pad to select x2, x4,

x6, or x8 Zoom magnification. At this point you may press

CLR

to return to the normal display or you may press

the arrow on the Page control pad to select Auto or

Manual Zoom.

Auto zoom

Once you have set the zoom magnification, you may select

either auto or manual zoom control. Select auto zoom, and

the FishFinder will automatically control the position of the

Zoom window. The auto zoom control constantly tracks the

bottom contour, and adjusts the position of the Zoom

window accordingly with changes in depth. This feature is

particularly useful when fishing for species of fish which

stay close to the bottom. Use the < and > arrows on the

Page control pad to select auto zoom. Press the

arrow

on the Page control pad to leave this display, and store the

auto zoom setting.

Manual zoom If you select manual zoom, you can choose the position of

the zoom area yourself. Use the < and > arrows on the

Page control pad to select manual zoom.

Once you make this choice, you can set the zoom area

yourself. You do this after you exit the Zoom Settings

display, and you are looking at the Zoom display itself. You

can manually move the Zoom area up or down by pressing

the

and

arrows on the Page control page. The

location of the zoom area is shown by the dark vertical line

at the very right-hand edge of the display.

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

CLEAR

If you are done with your setup changes, press the

button to go back

arrow on

to the normal display. To select the next menu item, press the

the Page control pad.

Frequency Setting

“Frequency” is a measure of how fast the sound waves change or

“vibrate.” This unit uses sound waves with two different frequencies – 50

kHz and 200 kHz. For an explanation on the uses of these two frequen-

cies, see the section on “Choosing a Frequency.”

From the area of the display for the zoom settings, press the

arrow on

the Page control pad. The next menu item will allow you to make the

frequency setting. See Fig. 4-7.

Fig. 4-7

Frequency

Setting

Frequency

Use the < and > arrows on the Page control pad to make

your choice.

You have four choices here:

•

200 kHz, single frequency – The unit will use the narrow 200 kHz

beam. The fish symbols will be solid.

50 kHz, single frequency – The unit will use the wider 50 kHz beam.

The fish symbols will be hollow.

200 kHz, dual frequency – The unit will use both frequencies, but the

image on the display will be generated using the information from the

narrow 200 kHz beam.

•

50 kHz dual frequency – The unit will use both frequencies, but the

image on the display will be generated using the information from the

wider 50 kHz beam.

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

If you are using one of the dual frequency choices, some of the fish may

be revealed by one beam, but not the other. If a fish is detected by the

narrow 200 kHz beam, the symbol for that fish will appear solid. Any fish

which are detected by the wider 50 kHz beam will have fish symbols

which are hollow.

CLEAR

If you are done with your setup changes, press the

button to go back

arrow on

to the normal display. To select the next menu item, press the

the control pad.

System Setup Display

Fig. 4-8

Reaching the

System Setup

Display

You can reach the System Setup display at any time by pressing the

Setup button twice. This means that you can reach this display, make a

change, then return to the normal display quickly. See Fig. 4-8. Figure

4-9 shows the items in this display.

To change one of the items, use the and arrows on the Page control

pad to move up or down in the display. This will highlight an area on the

display where the unit is ready to make a change. (This is like the “cursor”

on a computer.)

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 4-9

System Setup

Display

Once you have moved to the correct line, press the < or > arrows on the

Page control pad to change the entry. When you leave the display, the

unit will store any changes you have made.

Simulator

This unit has a built-in simulator. When the simulator is

enabled, it presents a realistic display. You can use this

display to learn about the features of the unit without

operating your boat. The information on this display is

generated by the unit itself, and does not come from a

transducer. When this mode is turned on, you will see the

word “Simulation” flashing on the display.

Fish symbol When the unit detects a fish, it can show this using a fish

symbol. A number above the symbol shows the depth of the

fish. The size of the symbol is related to the size of the fish.

In general, the larger the symbol, the larger the fish. (For

more information, see the section on “Fish Indications.”)

When the fish symbol is turned off, the unit indicates a fish

by showing an arch-shaped line. See Fig. 3-5. This kind of

display does not include the depth readings for the fish.

White line

This feature controls the way the unit displays strong and

weak echoes. When the white line feature is turned off, all

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

of the echoes are displayed in black. When the feature is

turned on, strong echoes are displayed using a crosshatch

(or “checkerboard”) pattern. A weaker return is shown

using a solid area of black or gray.

This feature helps to show the difference between the

strong echo from the bottom and the weaker echoes from

fish or weeds near the bottom.

Sidelooker

This item is used with the optional “Sidelooker” transducer.

This type of transducer sends sound waves out to the sides

of the boat. See Fig. 3-10. If you have installed this

transducer, use this line of the display to turn on the

Sidelooker mode.

Shallow Alarm You can set an alarm to trigger whenever the boat moves into

water which is shallower than a limit you set. Use the and

controls to move to the line for Shallow Alarm and use the

> arrow on the Page control pad to turn this item on. Once

you do this, the display will ask which depth you want to use

as a limit. Use the < and > controls to set the limit you want.

To turn this feature off, press the < control until the display

indicates zero feet, fathoms or meters.

When the shallow alarm is set, the letter “S” will appear in

the lower left-hand corner of the normal displays. If you

move into shallow water and trigger the alarm, the letter “S”

will begin to flash, and the buzzer will sound. Press the

CLEAR

button to silence the buzzer. The letter “S” will

continue to flash until you move into deeper water.

Deep Alarm An alarm can be set to trigger whenever the boat moves

into water which is deeper than a preset limit. Use the

and

controls to move to the line for Deep Alarm and use

the > control to turn this item on. Once you do this, the

display will ask which depth you want to use as a limit. Use

the < and > controls to set the limit you want. To turn this

feature off, press the < control until the display indicates

zero feet, fathoms or meters.

When the deep alarm is set, the letter “D” will appear in the

lower left-hand corner of the normal displays. If you move

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

into deep water and trigger the alarm, the letter “D” will

CLEAR

begin to flash, and the buzzer will sound. Press the

button to silence the buzzer. The letter “D” will continue to

flash until you move into shallower water.

Note:You may want to use both the Shallow Alarm and

Deep Alarm features when you are anchored. Set the limits

just a bit to either side of your anchor depth. When set this

way, the unit will trigger an alarm if the anchor drags and

the boat moves into shallower or deeper water.

Fish Alarm

This unit has an alarm which will trigger when the unit

detects a fish. Use the < and > controls to turn this item on

or off. The fish alarm feature will work even if the fish

symbols are turned off.

When the fish alarm is set, the fish symbol will appear in the

lower left-hand corner of the normal displays.

Buzzer

A buzzer can be set to sound when any of the alarm

conditions occurs (shallow, deep, or fish alarm). For the

shallow or deep alarms, the “S” or “D” symbol at the bottom

CLEAR

of the screen flashes. By pressing the

button, you can

silence the buzzer for the current alarm condition. The

“S” or “D” symbol will continue to flash as long as the alarm

condition is still present.

If the alarm condition occurs again, the buzzer will sound

again. (For example, this would happen if, after a shallow

alarm you move into deep water, then return to shallow

water.) You can silence the buzzer again by pressing the

CLEAR

button.

The Buzzer entry in the System Setup display allows you to

permanently silence the buzzer for all of the alarms. Use

the < and > controls to turn this item on or off. The buzzer

symbol at the bottom of the screen will appear hollow.

Once you do this, if a shallow alarm or deep alarm occurs,

the “S” or “D” symbol will flash, but the buzzer will not

sound. You can enable the buzzer again at any time by

calling up the System Setup display, going to the line for

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Buzzer, and turning the item on again. The buzzer symbol

at the bottom of the screen will appear solid.

Each time you press one of the buttons on the display

panel, the buzzer will “beep.” The buzzer will continue to

do this, regardless of the setting of the Buzzer option in the

System Setup display.

Depth Units This item sets the units used by the depth display. You can

choose feet (FT), fathoms (FA), or meters (M). Use the <

and > controls to make your choice.

CLEAR

If you are done with your setup changes, press the

to the normal display.

button to go back

Setup Instructions for Sidelooker

Some installations include the optional Sidelooker transducer. We

described the operation of this transducer in Section 3. If your boat has

this transducer, there are some extra setup steps required.

The Sidelooker feature must be turned on using the System Setup display.

SETUP

Press the

button twice to reach this display. Press the

arrow on

the Page control pad three times to reach the line labeled “Sidelook.”

Press the > arrow on the control to turn the feature on.

The System Setup display includes a line which allows you to set the

Chart Speed. This setting for Chart Speed affects the standard displays,

and also the Sidelooker display.

CLEAR

Once the settings on the System Setup display are correct, press the

button to go back to the normal display.

Next, press the > arrow on the Page control pad until you see the

Sidelooker page.

The next job is to set up the range, sensitivity, and chart speed for the

Sidelooker feature. While the unit is displaying the Sidelooker page, press

SETUP

the

button once. The setup menu for the Sidelooker range will

appear.

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 4-10

Sidelooker

Range Settings

Once the Sidelooker feature is turned on, the FishFinder uses two range

settings: one for the standard displays, and a second for just the

Sidelooker feature. The menu item shown here sets the range for just the

Sidelooker. (This will not change the range setting for the other display

pages.)

The range for the Sidelooker uses the Manual setting only. Select the

range you want to use. The maximum range of the Sidelooker transducer

is 150 ft or 45 meters.

Press the

arrow on the Page control pad to move to the next menu item.

Fig. 4-11

Sidelooker

Sensitivity Settings

This menu item allows you to set the sensitivity for the Sidelooker feature

only. (This will not change the sensitivity setting for the other display

pages.) Choose Auto or Manual sensitivity. If you choose Manual

sensitivity, use the < and > arrows on the Page control pad to adjust the

sensitivity.

CLR

At this point, you can press the

display.

button to go back to the Sidelooker

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

If you press the

arrow on the Page control pad, the unit will move to

the remaining menu items – zoom, frequency, and log reset. The zoom

and frequency settings are for the normal displays – they will not change

the Sidelooker feature. The log reset menu will operate normally.

Resetting the Unit to Factory Defaults

It is easy to reset all of the settings on the FishFinder at the same time.

PWR

CLEAR

When the unit is off, press the

and

buttons at the same time.

(Release the buttons as soon as the FishFinder begins to operate.) All of

the settings will be reset to the values listed below, and the trip log will be

reset to zero.

Default Settings

When the FishFinder is new, it uses a number of preset “default” settings.

Here is a list:

Function

model

Default - US model

Default - Europe

Range

Auto

3 (fast)

Auto/x4

Dual 200 kHz

Off

Auto

Sensitivity

Chart Speed

Zoom

Auto

3 (fast)

Auto/x4

Dual 200 kHz

Off

Frequency

Simulator

Fish symbols

White line

Sidelooker

Depth units

Shallow alarm

Fish alarm

Deep alarm

Buzzer

Off

FT (feet)

Off

M (meters)

Off

Setup Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

5 – Maintenance and Troubleshooting

Periodically check the display unit, cable, and transducer. Be sure all

components are free of corrosion and are securely mounted. Check all

cables for signs of chafing or abrasion. Be sure all of the connections to

the boat’s DC power and ground system are clean and tight.

Cleaning Instructions

Always keep the display unit clean. Use a soft, clean cloth to wipe off the

display panel. Do not use abrasive cleansers, chemical cleaners or

solvents. Use a glass cleaner or a suitable general-purpose detergent.

If you operate your boat in salt water, you will have to protect the hull with

antifouling paint. Use caution when sanding or cleaning the outside of the

hull near the transducer. Harsh cleaning solvents such as acetone may

damage the transducer.

Sea growth can collect quickly on the bottom of the transducer. This can

reduce the performance in just a few weeks. To prevent this, coat the

bottom of the transducer with a thin layer of paint. Use only a water-based

antifouling paint, or a water-based paint specifically designed for transduc-

ers. Apply it with a brush.

If your transducer becomes fouled or stops working because of sand or

sea growth, use a stiff brush to clean it. You may sand the surface with a

fine-grit wet or dry sandpaper (#320 grade or finer), but this will affect the

performance of the unit when the boat is moving at higher speeds.

Troubleshooting Suggestions

If the unit is not working correctly, there may be a simple cause. Before

you call for service help, please check these points:

The FishFinder display unit will not turn on –

1. The unit may actually be operating, but the contrast may have been

set to the “full light” or “full dark” setting. Turn on the unit by pressing

PWR

CLEAR

the

and

buttons at the same time to change all settings to

the factory defaults. See the default settings on page 59.

2. If the power wiring includes a fuse, it may be blown. Also check the

circuit breaker or main battery switch.

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

3. You may have reversed the power connections. Follow the DC power

lines all the way back to the battery. The red wire should connect to

the positive terminal (+) on the battery or power source, and the black

wire should connect to the negative terminal (-) (also called “ground”

or “earth”). If the polarity is not correct, reconnect the leads properly

and check again.

4. The battery or DC power source may not be producing the correct

voltage. The FishFinder needs at least 11 volts to operate. If the

voltage is lower, check for loose or corroded connections, or a

problem with the power source.

The display unit “freezes” (temporarily or permanently) –

1. Check that the display has not been stopped using the Chart Speed

setting. (If the adjustment bar is moved all of the way to the left, the

display will freeze.)

2. A source of electrical “noise” may be interfering with the unit’s

operation. Both the transducer cable and the power cable for the

FishFinder should be routed as far as possible from all other wiring on

the boat.

To locate the source of the noise, turn on the FishFinder. Next, turn

on each electrical device on the boat, but just supply power to one

device at a time. This may reveal the cause of the problem. Move

the FishFinder, the other unit, or the wiring. A movement of just a few

inches can make a big difference. If it is necessary to cross any

wires, make the crossing at a right angle.

Start the motor in neutral and increase the RPM speed. This can

reveal a problem with the wiring for the boat’s ignition, alternator, or

tachometer. It may help to use resistor-type spark plugs or spark plug

cables on the boat’s motor. You can also try a noise-suppression filter

on the alternator.

3. One of the wiring connections may be loose. All of the connections

should be clean, tight, and insulated. Soldering is the best way of

making these connections. Protect each connection with a piece of

shrink-wrap tubing.

4. The transducer cable may be damaged. Check for any point where

the wiring may be pinched or bent. Look for signs that water has

gotten into the cable. If the transducer cable is damaged, the

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

transducer and cable should be replaced as a unit. Contact

Raymarine for instructions.

The display unit does not see the bottom or fish –

1. Be sure the display unit is not using the Simulation mode. (If this is

the case, the word “Simulation” will flash on the display.)

2. On a unit with the transom-mount transducer, the transducer may

have “kicked up” because it hit an obstruction. See Fig. 2-4. Move

the transducer down into the working position.

3. The unit may be set for Manual sensitivity, and be using a very low

sensitivity setting. To reset all of the values to the factory defaults, turn

PWR

CLEAR

on the unit by pressing the

and

buttons at the same time.

See the default settings on page 59.

4. The transducer may not be vertical. Be sure that the transducer is

aiming straight down, or within 10° of vertical.

5. If the transducer is an in-hull type, be sure that it is installed correctly.

The transducer should be “looking” through just one layer of fiber-

glass hull material, no more than 1" (25 mm) thick. The transducer

should be firmly attached to the hull using the correct type of adhe-

sive/sealant.

6. The face of the transducer may be covered or fouled. Use a stiff

brush to clean it. You may also sand the surface with a fine-grit wet

or dry sandpaper (#320 grade or finer), but this will affect the perfor-

mance of the unit when the boat is moving at higher speeds.

7. If the FishFinder is using the Auto Sensitivity setting, it may be

reacting to an increase in electrical “noise.” As the level of noise

increases, the sensitivity automatically adjusts, and the unit can lose

its ability to see the bottom or fish. Check for problems with the wiring

as described in the section on “Display unit freezes.”

8. The voltage from the power source may be low. This affects the

transmitting power of the FishFinder. Check the connections as

described in the section on “The display unit freezes.”

The FishFinder does not display fish arches –

1. Be sure the Fish Symbol feature is turned off. See the instructions for

the System Setup display.

2. The FishFinder will not display arches unless the boat is moving. If

the boat is stopped, fish will appear on the display as straight lines.

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

3. The transducer may not be aimed straight down. In order to display

complete arches, the transducer must be vertical.

4. The sensitivity setting may not be high enough. Go to the Setup

Menu, choose Manual Sensitivity, and increase the sensitivity.

The display disappears or is unreliable when the boat is moving at

high speeds –

1. Increased turbulence around the transducer may be “confusing” the

unit. Move the transducer to a location where there is less turbulence

when the boat is moving.

2. If the FishFinder is using the Auto Sensitivity setting, it may be

reacting to an increase in electrical “noise.” As the level of noise

increases, the sensitivity automatically adjusts, and the unit can lose

its ability to see the bottom or fish. Check for problems with the wiring

as described in the section on “The display unit freezes.”

The display unit shows lots of background “noise” –

1. The unit may be set to use the manual sensitivity adjustment, and the

sensitivity may be set too high. See the information on “Setup

Instructions.”

2. The transducer may be mounted incorrectly, or may be fouled. Check

the mounting as described in Section 2. Clean the transducer as

described earlier in this section.

The depth setting flashes often –

Note: Normally, this indicates that the bottom has moved out of range.

1. The transducer may not be installed correctly, or the signal may not

be reaching the display unit. Recheck the instructions in “Mounting

the Transducer” in Section 2. Check the transducer cable for signs of

damage. If the cable is damaged, the transducer and cable should be

replaced as a unit.

2. The voltage reaching the unit may be low, and this may be affecting

the transmitting power. Check for problems with the wiring as

described in the section on “The display unit freezes.”

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Contact Raymarine

For marine product and services information

Visit the Raymarine World Wide Web site for the latest information on the

newest Raymarine electronic equipment and systems:

www.raymarine.com

For accessories and parts

Many Raymarine accessory items and parts can be obtained directly

from your authorized Raymarine dealer. However, if you are in need

of an item not available from the retailer, please contact Raymarine

Customer Service at 1-800-539-5539, extension 2333 or (603) 881-

5200, extension 2333. Customer Service is available Monday through

Friday, 8:15 a.m. to 5:00 p.m. Eastern Standard Time or Eastern

Daylight Savings Time.

If placing an order, please have the Raymarine item or part number

ready when calling. (See the Optional Accessory List on page 2 in this

manual.) If you are not sure which item is appropriate for your unit,

you should first contact the Technical Support Department at 1-800-

539-5539, extension 2444 to verify your requirements.

For technical support

Please call 1-800-539-5539, extension 2444 or (603) 881-5200, extension

2444. The Raymarine Fax number is 1-603-634-4756.

Our Technical Support Specialists are available to answer questions about

installing, operating, and troubleshooting all Raymarine products. Ques-

tions may be addressed directly to our Technical Support Department via

the Internet at:

[email protected]

For product repair service

In the unlikely event your Raymarine unit should develop a problem, please

contact your authorized Raymarine dealer for assistance. The dealer is

best equipped to handle your service requirements, and can offer timesav-

ing help in getting the equipment back into normal operation.

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

In the event that repairs cannot be obtained conveniently, product service

may also be obtained by returning the unit to Raymarine’s Product Repair

Center using the prepaid UPS shipping tag supplied with the unit. Return

the unit to:

Raymarine Product Repair Center

22 Cotton Road, Unit D

Nashua, NH 03063-4219 USA

The Product Repair Center is open Monday through Friday, 8:15 a.m. to

5:00 p.m. Eastern Standard Time or Eastern Daylight Savings Time. All

products returned to the Repair Center are registered when they arrive. A

confirmation letter will be sent to you acknowledging the repair status and

listing the product’s reference number. Should you wish to inquire about

the repair status of your unit, contact the Product Repair Center at 1-800-

539-5539, extension 2118. Please have the product reference number or

unit serial number ready when you call. We will do everything possible to

repair the unit and return it to you as quickly as possible.

Raymarine in Europe

In Europe, support, service, and accessories are available from

Raymarine Limited:

Raymarine Limited

Anchorage Park, Portsmouth

PO3 5TD England

Tel:

Fax:

+44 (0) 23 9269 3611

+44 (0) 23 9269 4642

Technical support is available via the Internet. Questions may be sent

directly to this address:

[email protected]

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

Prepaid Return Service

The return label included with your Raymarine unit provides free ground

shipping to our Product Repair Center for all warranty repairs. This

service is available only to customers within the continental United States.

To return your Raymarine unit for warranty repair, please follow these

steps:

1. Fill out the service information card completely.

2. Pack your FishFinder and the service information card in a suitable

shipping container. It is best to use the original carton, if it is avail-

able.

3. Fill in your name, address and zip code.

4. Attach the label to the outside of the shipping carton. Be sure to

retain the shipping receipt.

5. Give the package to your nearest shipping outlet, or directly to the

driver. Your Raymarine unit will be shipped directly to our Product

Repair Center.

Maintenance andTroubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance and Troubleshooting

Download from Www.Somanuals.com. All Manuals Search And Download.

6 – Specifications

General Information

Display panel

Panel dimensions

No. of dots

FSTN high-contrast LCD

3.6" H (61 mm) x 2.4" W (91 mm)

240 x 64

LCD contrast

Backlight

Adjustable, with temperature compensation

LCD panel, on/off

Operating modes

FishFinder mode (standard mode)

Zoom mode

A-Scope mode

Digital mode

Sidelooker mode

Keys

Silicon rubber

Memory backup

Power source

Power consumption

Non-volatile, no battery required

11.0 to 16.1 V DC

backlight off - approx. 2.0 W

backlight on - approx. 4.5 W

5.3" H (134 mm) x 5.2" W (133 mm)

x 2.7" D (69 mm)

Dimensions (w/o bracket)

Weight

1.1 lbs (0.5 kg)

Waterproofing

EMI resistance

U.S.C.G., CFR 46

IEC 945

Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

FishFinder Functions

Range

Auto or manual

FT (feet)

100 150

250

400 600 1000

1500 2000

FA (fathoms)

M (meters)

100 150

200 350

120 200 300

500 650

Zoom size

x2, x4, x6, x8

Chart speed

White line

Freeze, slow, medium, fast

On/ Off

Alarms

Shallow, deep, fish

5 sizes

Fish symbols

Output power

Frequency

300 W(rms)

50 kHz, 200 kHz or dual operation

200kHz: 16° @ -6db

50kHz: 65° @ -6db

Feet, fathoms, meters

3 digits (under 2.0 ft in ideal conditions)

Auto or manual

Transducer beam angle

Depth units

Numerical display

Sensitivity

Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

Connector Diagrams

DC power connector

Pin 1

Pin 2

Ground (-)

12V DC (+)

(Connectors viewed looking

toward rear of display unit.)

Transducer connector

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

Pin 9

Depth TX+

Depth TX-

L Select

Temp

R Select

Speed signal/voltage +

Shield ground

+12V (sidelooker)

L/R receive

Fig. 6-1

Connectors

Specifications

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary of Terms

Aft: Near or toward the rear part of the boat (nautical term).

Background noise: False or meaningless echo returns produced by

bubbles, water turbulence, or debris

Bow: The front of the boat (nautical term).

Cavitation: Air bubbles in the water which affect the readings of a

transducer. These are normally caused by mounting the transducer

at an incorrect angle or location.

Chart Speed: The rate at which echoes scroll across the display.

Cursor: On a setup display, the place where the unit is ready to make a

change or enter new information. This point is highlighted. You can

move up or down the list or display using the

and

controls.

Deadrise angle: The slope or angle of the underside of the hull, mea-

sured in the side-to-side direction.

Default value: A value or setting which is pre-loaded into the unit at the

factory.

Fairing block: A block used when mounting a thru-hull transducer. The

fairing block shims the transducer to align it on a perfect horizontal

plane versus the rise of the hull.

Fathom: A unit of depth equal to 6 feet.

Frequency: The rate at which a sound source vibrates, or the rate at

which a sound wave changes.

Fore: Near or toward the front part of the boat (nautical term).

Keel: The center of the hull, running from the bow to the stern.

kHz: “Kilo-Hertz” – a measure of frequency (For example, 200 kHz =

200,000 oscillations per second.)

Kick-up bracket: A bracket which is installed on the transom of a boat

and holds the transducer in place. When the transducer strikes an

obstruction, it is designed to release or “kick up” out of the water to

prevent any damage.

Glossary

Download from Www.Somanuals.com. All Manuals Search And Download.

Knot: One nautical mile per hour (1.15 statute miles per hour).

LCD: “Liquid Crystal Display” - A technology used to produce flat-panel

displays.

Nautical mile: 6076 feet

Port: Left side of the boat, when facing the bow (nautical term).

PVDF: “Poly Vinylidene Fluoride” – A unique polymer plastic that has the

ability to convert sound waves into electrical impulses. PVDF is used

in the optional Sidelooker transducer for excellent detection of fish in

the horizontal direction.

Range: The depth scale for the unit. The maximum distance the unit will

be able to see at a particular range setting.

Sensitivity: The ability of a receiver to distinguish between echoes of

different strengths. In general, use a higher sensitivity setting for

deep water, and a lower setting for shallow water.

Starboard: Right side of the boat, when facing the bow (nautical term).

Statute mile: 5280 ft.

Stern: The rear of a boat (nautical term).

Thermocline: A level in the water where two areas of differing water

temperature meet. Sometimes a thermocline can reflect sonar waves

and present a false display.

Transducer: A device which sends and receives high frequency sound

waves through the water.

Transom: The rear-most part of the boat’s hull, often a flat panel.

White Line: A feature used to help display fish near the bottom. This

feature helps to show the difference between weak returns (including

fish near the bottom) and strong returns (including the bottom itself).

Zoom: A way of magnifying or enlarging part of the display to give a

better view of a section of the water.

Glossary

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited Warranty Certificate

Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and

workmanship, and will repair or exchange any parts proven to be defective in material and

workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except

as provided below.

Defects will be corrected by Raymarine or an authorized Raymarine dealer. Raymarine will, except

as provided below, accept labor cost for a period of 2 years/24 months from the date of sale to end user.

During this period, except for certain products, travel costs (auto mileage and tolls) up to 100 round

trip highway miles (160 kilometers) and travel time of 2 hours, will be assumed by Raymarine only

on products where proof of installation or commission by authorized service agents, can be shown.

Warranty Limitations

Raymarine Warranty policy does not apply to equipment which has been subjected to accident, abuse

or misuse, shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or

equipment on which the serial number has been altered, mutilated or removed.

Except where Raymarine or its authorized dealer has performed the installation, it assumes no

responsibility for damage incurred during installation.

This Warranty does not cover routine system checkouts or alignment/calibration, unless required by

replacement of part(s) in the area being aligned.

A suitable proof of purchase, showing date, place, and serial number must be made available to

Raymarine or authorized service agent at the time of request for Warranty service.

Consumable items, (such as: Chart paper, lamps, fuses, batteries, styli, stylus/drive belts, radar mixer

crystals/diodes, snap-in impeller carriers, impellers, impeller bearings, and impeller shaft) are

specifically excluded from this Warranty.

Magnetrons, Cathode Ray Tubes (CRT), TFT Liquid Crystal Displays (LCD) and cold cathode

fluorescentlamps (CCFL),hailer horns,andtransducers are warrantedfor 1year/12 monthsfromdate

of sale. These items must be returned to a Raymarine facility.

All costs associated with transducer replacement, other than the cost of the transducer itself, are

specifically excluded from this Warranty.

Overtime premium labor portion of services outside of normal working hours is not covered by this

Warranty.

Travel cost allowance on certain products with a suggested retail price below $2500.00 is not

authorized. When/orifrepairsarenecessary,theseproductsmustbe forwardedtoaRaymarinefacility

oran authorized dealerat owner’sexpense willbe returned via surfacecarrierat no costto the owner.

Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded on

all products. Travel costs which are excluded from the coverage of this Warranty include but are not

limited to: taxi, launch fees, aircraft rental, subsistence, customs, shipping and communication charges

etc. Travel costs, mileage and time, in excess to that allowed must have prior approval in writing.

TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW:

(1) THIS WARRANTY IS STRICTLY LIMITED TO THE TERMS INDICATED HEREIN, AND

NO OTHER WARRANTIES OR REMEDIES SHALL BE BINDING ON RAYMARINE

INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABLE OR

FITNESS FOR A PARTICULAR PURPOSE.

(2) Raymarine shall not be liable for any incidental, consequential or special (including punitive or

multiple) damages.

All Raymarine products sold or provided hereunder are merely aids to navigation. It is the

responsibility of the user to exercise discretion and proper navigational skill independent of any

Raymarine equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Factory Service Centers

United States of America

Raymarine,Inc.

UK, Europe, Middle East, Far East

Raymarine Ltd

Anchorage park, Portsmouth

PO3 5TD, England

22 Cotton Road, Unit D

Nashua, NH 03063-4219 USA

Telephone: +1 603 881 5200

Telephone: +44 (0)23 9269 3611

Fax: +44 (0)23 9269 4642

www.raymarine.com

Fax:

+1 603 864 4756

www.raymarine.com

Sales & Order Services

Telephone: +1 800 539 5539 Ext. 2333 or

+1 603 881 5200 Ext 2333

Customer Support

Telephone: +44 (0)23 9271 4713

Fax: +44 (0)23 9266 1228

Technical Support

Email: techsupport@raymarine.com

Telephone: +1 800 539 5539 Ext. 2444 or

+1 603 881 5200 Ext 2444

Email: techsupport@raymarine.com

Product Repair Center

Telephone: +1 800 539 5539 Ext. 2118

Stick barcode label here

Purchase date

Purchased from

Dealer address

Installed by

Installation date

Commissioned by

Commissioning date

Owner’s name

Mailing address

This portion should be completed and retained by the owner.

Download from Www.Somanuals.com. All Manuals Search And Download.

PYLE Audio Stereo System PT 649D User Guide
Qualcast Lawn Mower 16 18 User Guide
RCA CRT Television F19420 User Guide
RCA Satellite Radio EZDVD2 User Guide
Remington Blower RM193B User Guide
RocketFish Video Game Controller RF GGC001 User Guide
Sapphire Audio Digital Camera Speed camera User Guide
Schneider Electric Network Router 17S Series User Guide
Sears Washer Dryer 91701 User Guide
Seiko Watch Cal 5M65 User Guide