Table of Contents
PAGE
Chapter 1 Specifications ........…..............................................
Chapter 2 Installation .......…..................................................
Installing the Radio.................................................................
Ignition Noise Interference ......................................................
Antenna …..............................................................................
External Speaker .....................................................................
Public Address .......................................................................
Chapter 3 Operation ....…........................................................
Controls and Indicators ..........................................................
Front Panel .............................................................................
Rear Panel .............................................................................
Operation …...........................................................................
Microphone ............................................................................
2
3
3
4
4
4
4
5
5
5
8
9
9
RCI-6300F25/150
AM/FM Amateur Transceiver
With Built-in Frequency Counter
Procedure to Receive .............................................................. 10
Procedure to Transmit ............................................................. 10
Memo …................................................................................... 11
LIMITED WARRANTY …............................................ Inside Back Cover
Owner's Manual
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
Chapter 3 Operation
Controls and Indicators
Front Panel
4. Mount the microphone bracket near the radio in an easily accessible
spot using the two screws provided.
11
12
13 14 15 16 17 18 19 20
Ignition Noise Interference
With weak signals, you may experience interference of the signal by
background noise. This radio has NB and ANL controls which will help
reduce background noise from sources such as your ignition system.
However, background electrical noise may come from several sources
and all noise may not be eliminated. With extremely weak signals, you
can operate this radio with the engine turned off, which should improve
reception. If the ignition noise level is too high to allow proper operation
under most conditions, you should have your installation of the radio
checked by a qualified technician.
Ranger
10
1
2
3
4
5
6
7
8
9
Antenna
This radio has a jack in the rear for a standard PL-259 antenna plug. If
you are looking for the most range for your transmission, use a vertically
polarized, quarter-wave length antenna. If antenna height is a problem,
you may use a shorter, loaded-type whip antenna although you can
expect some lost of transmission range.
1. SQUELCH CONTROL: This control is used to control or eliminate
receiver background noise in the absence of an incoming signal. For
maximum receiver sensitivity, it is necessary that the control be
adjusted only to the point where the receiver background noise is
eliminated. Turn fully counterclockwise and then slowly clockwise
until the receiver noise just disappears. Any signal to be received
must now be slightly stronger than the average received noise.
Further clockwise rotation will increase the threshold level that a
signal must overcome in order to be heard. Only strong signals will
be heard at a maximum clockwise squelch setting.
To improve performance, your antenna should be matched to your radio.
Your antenna can be adjusted so that it matches your radio.
External Speaker
The external speaker jack (EXT. SPK) on the rear panel is used for remote
receiver monitoring. The external speaker should have 8 ohms impedance
and be able to handle at least 4watts. When the external speaker is
plugged in, the internal speaker is disconnected.
2. ON/OFF VOLUME CONTROL: Turn clockwise to apply power to the
radio and to set the desired listening level.
Public Address
3. RF GAIN CONTROL: This control is used to reduce the gain of the RF
To use the Public Address (PA) function, first connect an external speaker
to the PA. SP. Jack on the rear of the radio. See the above specifications
for a proper external speaker. Keep the speaker away from the
microphone to avoid acoustic feedback.
amplifier under strong signal conditions.
4. MIC GAIN CONTROL: Adjust the microphone gain in the transmit
mode. This control is used to set the audio level of the microphone for
maximum performance and clarity.
- 4 -
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Continued)
Operation (Continued)
5. MODE SWITCH: This switch allows you to select one of three
position, the Standing Wave Ratio (SWR) of your antenna. There are no
adjustments because the SWR circuit this radio calibrates itself
automatically.
following operating modes: PA/FM/AM.
6. Fr. POOL: The Frequency Pool allow the user to select the desired
17. NB/ANL SWITCH: In the NB/ANL position, the RF Noise Blanker and
the automatic Noise Limiter in the audio circuits are also activated. The
Noise Blanker is very effective in eliminating repetitive impulse noise
such as ignition interference.
segments of frequencies.
7. ECHO/TIME CONTROL: The ECHO control is used for echo effect. The
TIME control is used to control the intervals of the echo sound.
8. RF POWER CONTROL: This control enables adjustment of RF power
18. ROGER BEEP SWITCH: When this switch is placed in the ROGER
BEEP position, the radio automatically transmits an audio tone at the
end of your transmission. This indicates the end of your transmission
so that people who are having trouble hearing you will know that you
are done speaking. As a courtesy to others, use the Roger Beep only
when necessary.
output continuously up to the rated output power.
9. TALKBACK/OFF CONTROL: Adjust this knob for desired volume of
Talkback. This is used to monitor your own voice. Or example, you
could use this feature to compare different microphones.
10. CHANNEL SELECTOR: This control is used to select a desired
transmit and receive channel.
19. + 10KHz SWITCH: In the + 10KHz position, the transmit and receive
frequency is shifted 10KHz up.
11. FRONT PANEL METER: The front panel meter allows the user to
monitor signal strength and RF power out level.
20. CHANNEL DISPLAY: The channel display indicates the current
12. TX/RX LED: The red LED indicates the radio is in the transmit mode.
selected channel.
The green indicates the radio is in the receive mode.
13. FREQUENCY COUNTER: This frequency counter indicates the
transmit frequency digitally.
14. DIM/BRT SWITCH: This switch is used to adjust the brightness of the
meter and LED display for optimum intensity for day or nighttime
driving.
15. HI/LOW TONE SWITCH: This switch changes tone quality in receive
only. In LO position, bass is increased and in HI position, treble is
increased.
16. S-RF/SWR SWITCH: In the S-RF position, the meter swings
proportionally to the strength of the received signal. When transmitting,
the meter indicates relative RF output power. When in the SWR
- 6 -
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Continued)
Operation (Continued)
Rear Panel
Operation
A. Microphone
3
4
The receiver and transmitter are controlled by the push-to-talk switch on
the microphone. Press the switch and the transmitter is activated, release
switch to receive. When transmitting hold the microphone two inches
from the mouth and speak clearly in a normal “voice”. The transceiver
comes complete with low-impedance dynamic microphone.
ANT.
PA.SP.
EXT.SP.
_
+
POWER
For best results, the user should select a low-impedance dynamic type
microphone or a transistorized microphone.
1
2
The microphone should provide the functions shown in schematic below.
4 WIRE MIC CABLE
1. ANTENNA: This jack accepts a 50 ohms coaxial cable with a PL-259
Pin Number
Mic Cable Lead
Audio Shield
Audio Lead
Transmit Control
Receive Control
style plug.
1
2
3
4
2. POWER: This accepts 13.8 VDC power cable with built-in fuse. The
power cord provided with the radio has a black and red wire. The
black goes to negative and the red goes to positive.
3. PA. SP.: This jack is for PA operation. Before operating, you must
first connect a PA speaker (8 ohms, 4W) to this jack.
4. EXTERNAL SPEAKER: This jack accepts a 4 - 8 ohm, 5watt external
speaker. When the external speaker is connected to this jack, the built-
in speaker will be disabled.
1
4
2
3
TX
MIC
Transceiver Microphone Schematic Diagram
- 9 -
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Continued)
Memo
B. Procedure to Receive
1. Be sure that power source, microphone and antenna are connected to
the proper connectors before going to the next step.
2. Turn unit on by turning VOL knob clockwise.
3. Set the VOL for a comfortable listening level.
4. Set MODE switch to the desired operation mode.
5. Listen to the background noise from the speaker. Turn the SQ knob
slowly clockwise until the noise just disappear. This SQ is now
properly adjusted. The receiver will remain quit until a signal is
actually received. Do not advance the control too far, or some of
weaker signals will not be heard.
6. Set the CHANNEL switch to the desired channel.
7. Set the RF gain control fully clockwise for maximum RF gain.
C. Procedure to Transmit
1. Select the desired channel of transmission.
2. Set the MIC GAIN to the level that will best suit your individual use.
3. If the channel is clear, depress the push-to-talk switch on the
microphone and speak in a normal voice.
- 10 -
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Ranger Communications Limited Warranty
Ranger Communication, Inc. (Ranger) warrants to the original purchaser only this
product against defects in material or workmanship, as noted below.
Effective December 1, 2001, the following Ranger Communications, Inc.'s products
are covered by a two (2) year limited warranty:
1. Amateur Radio Products: RCI-2950DX, RCI-2970DX, RCI-2980WX, RCI-
2985DX, RCI-2990DX, RCI-2995DX, RCI-6300FHP, RCI-6300FTB, RCI-
6900FHP, RCI-6900FTB.
2. Citizens Band Products: TR-100 Series, TR-296 (all models), TR-396F, TR-696F,
TR-696F SSB, TR-900 Series (all models).
The above products are warranted for the specified time period from the original date
of purchase as shown on the original purchaser’s bill of sale, receipted invoice, or
other proof of purchase. After this period, the original purchaser must pay for any
labor at the prevailing rate either at an authorized Ranger warranty repair facility or at
the factory.
In the event of a defect during the warranty period, Ranger shall, at its option, repair or
replace the defective product. Such action shall constitute the purchaser’s exclusive
remedy under this warranty.
401 W. 35th Street, Suite B
National City, CA 91950
(800) 446-5778 • FAX (619) 426-3788
A Return Authorization Number must be obtained from the Ranger Customer Service
Department before any returns for warranty repair will be accepted. Send the defective
product postage-paid, along with proof of the date of purchase (photocopy of the
original invoice or receipt), to:
Ranger Communications, Inc.
401 W. 35th Street, Suite B
National City, Ca 91950-7909
TEL: (800) 446-5778, (619) 426-6440
FAX: (619) 426-3788
E-mail: [email protected]
This warranty does not cover cosmetic damage or damage due to acts of God, accident,
misuse,
abuse,
negligence,
improper
installation,
UNAUTHORIZED
MODIFICATION, or any action in violation of the product’s instruction manual. This
warranty is valid only in the U. S. A.
1. "Limited" means that we will repair problems that are caused by factory defects,
only for the above mentioned products and time limit, at no charge. Work performed
by qualified technicians which did not cause any damage to the radio will not void the
warranty. Problems or damage caused by unqualified or misinformed technicians,
operator abuse or other miscellaneous actions may be able to be repaired, but there will
be a charge. This warranty is limited to the radio only.
2. Generally, if the warranty sticker is removed or cut, the radio is considered to be
"Void of Warranty". However, our policy is to be as lenient as we can, and to take this
into consideration. We will usually repair the radio - under warranty - if no abuse or
misuse is found. Radios that have parts removed cut or clipped; or the PCB has been
damaged, will not be repaired under warranty.
PRINTED IN TAIWAN
AT9000063K
Download from Www.Somanuals.com. All Manuals Search And Download.
|