Radio Shack Portable Radio 21 1679 User Guide

21-1679  
Weather Alert  
Handheld CB RADIO  
Thank you for purchasing your  
Weather Alert Handheld CB  
Radio from RadioShack.  
What’s Included  
CB Radio  
Ni-MH Battery Pack  
AA Battery Case  
AC Charger  
Antenna  
Hand Strap  
Belt Clip  
Users Guide  
FCC Rules  
Please read this users guide before installing, setting up  
and using your new CB radio.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A Look at Your CB Radio  
A Look at Your CB Radio  
Antenna  
SQUELCH  
OFF/VOLUME  
Channel  
Selection  
"UTTONS Ÿ/ź  
CH9/19 SCAN  
CB/WX  
H/L BEEP  
Internal Microphone  
LOCK/ALERT OFF  
LIGHT  
PTT  
ꢀ0USHŸTOŸ4ALK  
Internal  
Speaker  
Attaching the Belt Clip  
To attach the belt clip,  
slide it up until it locks  
into place.  
To remove the belt  
clip, pull the tab gently  
and slide the belt clip  
down.  
Hand Strap Hole  
Tab  
Belt  
Clip  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering Your CB Radio  
Powering Your CB Radio  
You can power your CB radio from one of these four sources:  
• The supplied rechargeable Ni-MH battery pack  
• Eight AA batteries (not included) using the supplied battery  
case  
• AC power using an AC-to-DC power supply (not included)  
• Vehicle power using a DC power cord (not included)  
Using the Ni-MH Battery Pack  
Charge the Ni-MH battery pack (using the supplied AC charger)  
FORꢀABOUTꢀꢁꢂꢀHOURSꢀPRIORꢀTOꢀUSINGꢀITꢀFORꢀTHEꢀÞRSTꢀTIMEꢃꢀØFTERWARDꢄꢀ  
it takes 14-16 hours to charge the battery pack when it is fully  
discharged.  
You can charge the battery pack while it is installed or removed.  
But the CB radio does not work during charging.  
To charge the battery pack:  
Connect the AC Charger to the  
CHG Jack, then plug it into an AC  
outlet. The CHARGE Indicator  
lights red and charging starts.  
Note: The supplied AC charger  
is for charging only, not for  
directly powering the CB.  
Latch  
4OŸINSTALLŸTHEŸBATTERYŸPACKꢁ  
CHG Jack  
Slide the battery pack onto the  
CB radio until it clicks. The battery  
CHARGE  
PACKꢀÞTSꢀONTOꢀTHEꢀ#"ꢀRADIOꢀONLYꢀ  
Indicator  
one way. Do not force it.  
To remove the battery pack, slide  
the battery pack in the arrow  
direction while holding up the  
latch.  
Slide to remove  
battery pack  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering Your CB Radio  
#AUTIONSꢁ  
To avoid injury, do not connect the AC charger to a ceiling  
outlet. After charging, disconnect the AC charger.  
You must use a Class 2 power supply that provides 16V DC  
and delivers at least 200mA. The barrel plugs center must  
BEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"mSCHG jack.  
4HEꢀSUPPLIEDꢀØ#ꢀCHARGERꢀMEETSꢀTHESEꢀSPECIÞCATIONSꢃꢀ5SINGꢀ  
ANꢀADAPTERꢀTHATꢀDOESꢀNOTꢀMEETꢀTHESEꢀSPECIÞCATIONSꢀCOULDꢀ  
damage the CB radio or adapter.  
• Always connect the AC charger to the battery pack before  
you connect it to an AC outlet, and disconnect the AC  
charger from the AC outlet before you disconnect it from the  
battery pack.  
• Overcharging your battery pack could shorten its life.  
• Do not charge your battery pack at temperatures below 14°F  
(–10°C) or above 131°F (55°C).  
You cannot recharge the Ni-MH battery pack using DC  
power.  
Recycle Rechargeable Batteries  
Placing rechargeable batteries in the trash can be  
harmful to the environment. Instead, recycle old  
rechargeable batteries at your local RadioShack store free of  
charge. RadioShack participates in the RBRC© battery recycling  
program, and is committed to preserving the environment and  
conserving natural resources. Call 1-800-THE-SHACK (1-800-  
843-7422) for more information.  
Using the AA Battery Case  
1. Turn off the CB radio if it is on.  
2. Pull the halves of the case apart to  
open it. Insert eight AA batteries,  
matching the polarity marks (+ and –).  
Snap the halves of the case together  
to close it.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering Your CB Radio  
3. Slide the battery case onto the CB radio until it clicks. The  
BATTERYꢀCASEꢀÞTSꢀONTOꢀTHEꢀ#"ꢀRADIOꢀONLYꢀONEꢀWAYꢀ$OꢀNOTꢀ  
force it.  
Replace the batteries when the sound becomes weak or  
distorted,  
appears, or the CB radio stops working.  
;
"ATTERYŸ.OTESꢁ  
• Dispose of old batteries promptly and properly. Do not burn  
or bury batteries.  
• Use only fresh batteries of the required size and type.  
• Do not mix old and new batteries, different types of batteries  
(standard, alkaline, or rechargeable), or rechargeable  
batteries of different capacities.  
• If you do not plan to use the CB radio with batteries for two  
weeks or longer, remove the batteries. Batteries can leak  
chemicals that can destroy electronic parts.  
Using AC Power  
To power your CB radio from your home,  
you will need a 12V DC power supply  
that provides a minimum of 2.5A at 12V  
and a DC power cord (neither included).  
1. Turn off the CB radio if it is on.  
2. Use the DC power cord to connect  
the CBs 12V DC PWR Jack and the  
DC power supply.  
3. Connect the DC power supply to an  
AC outlet.  
12V DC PWR Jack  
4. Turn on the CB radio to use.  
#AUTIONSꢁ  
You must use a Class 2 power supply that provides regulated  
13.8V DC and delivers at least 2.5A. The barrel plugs center  
MUSTꢀBEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"mS12V  
DC PWR jack. Using an adapter that does not meet these  
SPECIÞCATIONSꢀCOULDꢀDAMAGEꢀTHEꢀ#"ꢀRADIOꢀORꢀADAPTERꢃ  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Powering Your CB Radio  
• Always connect the power supply to the CB radio before you  
connect it to an AC outlet, and disconnect the power supply  
from the AC outlet before you disconnect it from the CB  
radio.  
Using Vehicle Power  
To power your CB radio from your vehicle, you will need a DC  
power cord (not included). You may also need a roof-mounted  
antenna to improve transmission quality and increase the  
transmission range.  
1. Turn off the CB radio if it is on.  
2. Use the DC power cord to connect the CBs 12V DC  
PWR jack and the vehicles 12V power source, such as the  
cigarette-lighter socket.  
3. Turn on the CB radio to use.  
#AUTIONSꢁ  
You must use a Class 2 power supply that provides regulated  
12V DC and delivers at least 2.5A. The barrel plugs center  
MUSTꢀBEꢀPOSITIVEꢀANDꢀTHEꢀBARRELꢀPLUGꢀMUSTꢀÞTꢀTHEꢀ#"ꢀRADIOmSꢀ  
12V DC PWR jack. Using an adapter that does not meet  
THESEꢀSPECIÞCATIONSꢀCOULDꢀDAMAGEꢀTHEꢀ#"ꢀRADIOꢀORꢀADAPTERꢃ  
• Always connect the power supply to the CB radio before you  
connect it to the vehicle outlet, and disconnect the power  
supply from the outlet before you disconnect it from the CB  
radio.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Your CB Radio  
Connecting Your CB Radio  
Installing the Antenna  
To install the supplied antenna, align the  
two slots on the antenna connector with  
the tabs on the BNC connector of the  
CB radio. Push the antenna connector  
to the CB radio and rotate the antenna  
connector clockwise until it locks into  
place.  
Installing an Optional Antenna  
The CBs BNC connector allows you  
to use a variety of optional antennas,  
including external mobile antennas and  
outdoor base station antennas.  
Always use the 50-ohm, RG-58, or RG-8 coaxial cable to connect  
an outdoor antenna. If the antenna is over 50 feet from the CB  
radio, use the RG-8 low-loss dielectric coaxial cable.  
Safety Precaution:  
If an outside antenna is installed, be sure the antenna system is  
grounded so as to provide protection against voltage surges and  
built-up static charges. When installing the antenna, be careful not  
to touch overhead power lines as contact with them might be fatal.  
Connecting an External Speaker or Microphone  
Connect an external speaker (not  
included) to the SPK jack of your  
CB radio. This mutes the CBs  
internal speaker.  
SPK  
Connect an external microphone  
(not included) to the MIC jack of  
your CB radio. This disables the  
CBs internal microphone.  
MIC  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your CB Radio  
Operating Your CB Radio  
Receiving  
1. Turn SQUELCH fully anticlockwise.  
2. Turn on the CB radio. A channel number and the signal  
meter appear. If necessary, press CB/WX so that a channel  
number and the signal meter appear.  
3. Press Ÿ or ź to select the desired channel.  
4. Adjust OFF/VOLUME to the desired volume level.  
5. Slowly turn SQUELCH back clockwise just until the noise stops.  
Note: Do not turn SQUELCH too far clockwise because you  
might cut out weak signals.  
RX below the signal meter indicates the CB radio is ready to  
receive transmissions.  
Transmitting  
Test receiving transmissions on  
Channel Number  
your CB Radio before trying to  
transmit a message.  
Signal Meter  
4OŸTRANSMITŸAŸMESSAGEꢁ  
1. Press and hold PTT. TX  
appears below the signal  
meter and the signal meter  
shows the output level. Hold  
the CB radio 2–3 inches from  
your mouth and speak in a  
normal voice to the internal microphone.  
ꢅꢃꢀ 7HENꢀYOUꢀÞNISHꢀSPEAKINGꢄꢀRELEASEꢀPTT.  
.OTESꢁ  
• If you transmit a message while the CB radio is displaying a  
weather alert (see Understanding Digital Weather Alert), the alert  
tone stops and WX displays steadily. To stop the alert tone  
without transmitting a message, press LOCK/ALERT OFF.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your CB Radio  
To avoid overheating the internal circuit, do not press and  
hold PTT nonstop for over two minutes.  
Safety Precaution  
Your wireless hand-held portable transceiver contains a low power  
transmitter. When the Push-to-Talk (PTT) button is pushed it sends  
out radio frequency (RF) signals. The device is authorized to  
operate at a duty factor not to exceed 50%. In August 1996, the  
Federal Communications Commissions (FCC) adopted RF exposure  
guidelines with safety levels for hand-held wireless devices.  
To maintain compliance with the FCCs RF exposure guidelines  
hold the transmitter and antenna at least 1 inch (2.5 centimeters)  
from your face and speak in a normal voice, with the antenna  
pointed up and away from the face. If you wear the handset  
on your body while using the headset accessory, use only the  
supplied belt clip for this product and when transmitting, take it  
out of the belt to ensure that the antenna is at least 1 inch (2.5  
centimeters) from your body.  
Settings  
High/Low Power Level  
Press H/L BEEP to switch  
between low power level (LOW  
appears) and high power level.  
Note: Low power level reduces the range of the CB radio.  
Backlight  
Press LIGHT to turn on the backlight; press again to turn off. The  
backlight turns off automatically after 10 seconds.  
Key Tone  
To activate the key tone, press and hold H/L BEEP for 2  
seconds. ͈Gappears. The CB radio sounds a beep when you  
press any key except PTT.  
To disable the key tone, press and hold H/L BEEP for 2 seconds  
again so that ͈Gdisappears.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your CB Radio  
Key Lock  
To activate key lock, press and hold LOCK for 2 seconds.  
6
appears. This locks all keys except PTT and LIGHT. To  
unlock key control, press and hold LOCK for 2 seconds again.  
Power Save  
If you do not press any key or if the CB radio does not receive  
any signal for about 10 seconds, the CB radio automatically  
enters power save mode. P. SAVE ßASHESꢃ  
Scanning Channels  
1. Press CB/WX to select the CB or weather mode.  
2. Press and hold CH9/19 SCAN for 2 seconds. SCAN appears,  
and the CB radio scans through all channels in the selected  
band. When it receives a strong signal, scanning stops.  
3. To deactivate scanning, press and hold CH9/19 SCAN for 2  
seconds or press the Ÿ or źꢀkey.  
.OTESꢁŸ  
pꢀ 7HENꢀYOUꢀTURNꢀONꢀTHEꢀ#"ꢀRADIOꢀFORꢀTHEꢀÞRSTꢀTIMEꢄꢀTHEꢀSCANꢀ  
feature is automatically set to ON in the weather band.  
To change weather channels manually, press the Ÿ or ź key.  
Using Channels 9 and 19  
Channel 9 is reserved for motorist assistance and for reporting  
emergency information about accidents, hazardous road  
conditions, etc. Channel 19 is used by truck drivers for general  
communication purposes.  
Press CH9/19 SCAN once to select channel 9, press again  
to select channel 19, press again to return to the previously  
selected channel.  
.OTESꢁŸ  
• When you select channel 9 or 19, you cannot press Ÿ or ź to  
change channels.  
• Always give priority to emergency messages on channel 9.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your CB Radio  
Listening to the Weather Band  
The FCC has allocated channels for use by National Oceanic  
and Atmospheric Administration (NOAA). Regulatory agencies  
in other countries have also allocated channels for use by their  
weather reporting authorities.  
NOAA and your local weather reporting authority broadcast  
your local forecast and regional weather information on one or  
more of these channels.  
Listening to a Weather Channel  
Weather Channel  
Press CB/WX to select weather  
mode. WX appears. The CB  
radio scans through the weather  
channels and then stops on the  
strongest channel. Press CB/WX  
again to return to CB mode.  
Note: You cannot adjust the  
power level or switch to  
channel 9 or 19 while listening to a weather channel.  
Turning Digital Weather Alert On and Off  
• Digital weather alert automatically scans in the background  
when you select the CB mode, unless you turn it off.  
• Press LOCK/ALERT OFF to turn digital weather alert on and off.  
In CB mode, WX displays as described below.  
WX Appearance  
WX not present  
WX flashes  
Weather Alert  
Weather Signal  
Not scanning for  
signal  
Not on  
On  
No signal found  
Signal found and  
locked in  
WX displays steadily  
On  
WX displays steadily for 2  
seconds and then flashes  
twice  
Signal found;  
scanning for signal  
On  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Your CB Radio  
Understanding Digital Weather Alert  
The weather service precedes each weather alert with a digitally-  
ENCODEDꢀ3Ø-%ꢀ 3PECIÞCꢀØREAꢀ-ESSAGEꢀ%NCODINGꢆꢀSIGNALꢄꢀTHENꢀ  
a 1050 Hz tone. When your local weather station broadcasts  
a weather alert signal, the CB radio sounds an alert tone and  
displays a message showing the alert level.  
SAME Event Code  
Alert Tone  
-ESSAGE  
Watch alert  
10 seconds  
A (Watch)  
WCH (Watch)  
W (Warning)  
TOR (Tornado)  
SVR (Severe)  
Warning alert  
10 seconds  
WRN (Warning)  
ADV (Advisory)  
S (Statement)  
RWT (Test)  
Statement alert  
10 seconds  
.OTESꢁ  
• The CB radio does not display the actual location referenced  
by SAME messages. It uses only the message portion of the  
SAME signal.  
• If severe weather threatens, do not wait for an alert tone;  
tune to the weather broadcast and monitor the weather  
information.  
• If a weather signal ends, the CB radio beeps three times  
(when the key tone is turned on) and only when the weather  
SIGNALꢀENDSꢀTHEꢀÞRSTꢀTIMEꢄꢀTHENꢀWXꢀßASHESꢀTOꢀINDICATEꢀTHEREꢀISꢀ  
no signal.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional Information  
Additional Information  
Legal Use of Your CB Radio  
The CB Radio service is a private, two-way, short-distance voice  
communications service for personal or business activities. For  
rules regarding legal CB radio use, see Part 95, Subpart D: FCC  
Rules for Operating a Citizens Band (CB) Radio published by the FCC.  
Common Uses for a CB Radio  
pꢀ 7ARNꢀOFꢀTRAFÞCꢀTIEꢇUPSꢀAHEADꢃ  
• Help truck drivers and delivery personnel learn road and  
TRAFÞCꢀCONDITIONSꢀANDꢀGETꢀASSISTANCEꢀINꢀLOCATINGꢀDESTINATIONSꢃ  
• Provide fast help in the event of emergency or breakdown.  
• Help construction crews coordinate the activities of different  
work crews.  
pꢀ ØSSISTꢀCOMMUNICATIONꢀBETWEENꢀSECURITYꢀOFÞCERSꢃ  
• Provide weather and road information.  
• Contact friends or other CB users on trips.  
pꢀ +EEPꢀINꢀTOUCHꢀWITHꢀYOURꢀOFÞCEꢀORꢀHOMEꢃ  
pꢀ "RINGꢀMOREꢀFUNꢀFORꢀCAMPINGꢄꢀÞSHINGꢄꢀANDꢀOTHERꢀSPORTSꢈꢀHELPꢀ  
LOCATEꢀAꢀFRIENDꢀORꢀÞNDꢀOUTꢀWHATmSꢀCOOKINGꢀBACKꢀATꢀCAMPꢃ  
Transmission Courtesy  
• Wait for a pause in someone elses transmission before you  
ask for a break.  
• If you do not receive an answer to your call after a second  
attempt, sign off and wait several seconds before trying again.  
• Do not hold down PTT when you are not talking. (This is  
called dead keying.)  
• Assist callers with directions, information about road  
conditions, and any other reasonable requests.  
Transmission Range  
The maximum range and quality of CB transmissions vary  
depending on the following conditions:  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional Information  
Type and quality of the antenna.  
• Height of the antennas mounting location (the higher the  
antenna, the better the signals range).  
• Surrounding terrain (mountains and tall buildings limit the range).  
• Weather conditions.  
• Number of nearby CBs operating on the same channel.  
Note: Your CB radios transmission range is generally line-of-  
sight. To ensure maximum range, always keep the battery  
pack fully charged or use fresh batteries.  
Common 10-Codes  
Citizens Band radio operators have largely adopted the 10-  
codes for standard questions and answers. These codes permit  
faster communication and better understanding in noisy areas.  
The following table lists some of the more common codes and  
their meanings:  
Code  
Meaning  
Code  
Meaning  
10-1 Receiving poorly  
10-2 Receiving well  
10-3 Stop transmitting  
10-4 OK, message received  
10-5 Relay message  
10-6 Busy, stand by  
10-7 Out of service  
10-8 In service  
10-22 Report in person to____  
10-23 Stand by  
10-25 Can you contact____  
10-26 Disregard last information  
10-27 I am moving to channel  
10-28 Identify your station  
10-32 I will give you a radio check  
10-33 %MERGENCYŸTRAFÚC  
10-9 Repeat message  
10-36 Correct time is____  
Transmission completed,  
standing by  
10-10  
10-37 Wrecker needed at____  
10-11 Talking too rapidly  
10-12 Visitors present  
10-38 Ambulance needed at____  
10-41 Please turn to channel____  
Advise Weather/Road  
conditions  
10-13  
10-42 4RAFÚCŸACCIDENTŸAT????  
10-17 Urgent business  
10-18 Anything for us?  
10-43 4RAFÚCŸTIEꢀUPŸAT????  
10-50 Break channel  
10-19 Nothing for you. Return to base 10-62 Unable to copy; use telephone  
10-20 My location is____  
10-21 Call by telephone  
10-70 Fire at____  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional Information  
Note: Although this table lists the meanings of the 10-codes  
in the form of a statement, they can also be phrased  
as questions (10-6: Are you busy? 10-20: What is your  
location?)  
Frequency Range  
Your CB radio receives and transmits on the following 40 CB  
channels:  
Frequency  
ꢀ-(Z  
Frequency  
ꢀ-(Z  
Frequency  
ꢀ-(Z  
Channel  
Channel  
Channel  
1
2
26.965  
26.975  
26.985  
27.005  
27.015  
27.025  
27.035  
27.055  
27.065  
27.075  
27.085  
27.105  
27.115  
27.125  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
27.135  
27.155  
27.165  
27.175  
27.185  
27.205  
27.215  
27.225  
27.255  
27.235  
27.245  
27.265  
27.275  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
27.285  
27.295  
27.305  
27.315  
27.325  
27.335  
27.345  
27.355  
27.365  
27.375  
27.385  
27.395  
27.405  
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
In addition, your CB radio can receive these weather service  
channels:  
Frequency  
ꢀ-(Z  
Frequency  
ꢀ-(Z  
Frequency  
ꢀ-(Z  
Channel  
Channel  
Channel  
1
2
3
162.400  
162.425  
162.450  
4
5
6
162.475  
162.500  
162.525  
7
162.550  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Specifications  
Receiver  
Frequency Coverage........ 26.965~27.405 MHz, 162.400~162.550 MHz  
Sensitivity...........................................................................1 μV for 10 dB  
Adjacent Channel Rejection ((S+N)/N)........................................... 60 dB  
Squelch................................................................Adjustable from 0.5 μV  
Audio Output Power (10% THD)................................................ 400 mW  
Current Drain............................. 80 mA (Standby); 400 mA (Max. Audio)  
Transmitter  
Frequency Coverage............................................... 26.965~27.405 MHz  
Power Output........................................................ 3 W (High); 1 W (Low)  
Conducted Spurious Emission Harmonics ..................................... 60 dB  
Type of Modulation ............................................................................. A3  
Frequency Tolerance ....................................................................0.002%  
Antenna Impedance.........................................................................50 Ÿꢀ  
Current Drain (@ Max. Modulation)...............1.3 A (High); 700 mA (Low)  
Dimensions (H× W× D) .......... 7.4 × 2.6 × 1.8 inch (186 × 65 × 47 mm)  
Weight (including battery pack & antenna)...................... 18.3 oz (520 g)  
3PECIÞCATIONSꢀAREꢀSUBJECTꢀTOꢀCHANGEꢀANDꢀIMPROVEMENTꢀWITHOUTꢀNOTICEꢃꢀ  
Actual product may vary from the images found in this document.  
Care  
Keep the CB radio dry; if it gets wet, wipe it dry immediately.  
Use and store the CB radio only normal temperature  
environments. Handle the CB radio carefully; do not drop it.  
Keep the CB radio away from dust and dirt, and wipe it with a  
damp cloth occasionally to keep it looking new.  
Modifying or tampering with the CB radios internal components  
can cause a malfunction and might invalidate its warranty and  
avoid your FCC authorization to operate it. If your CB radio is  
not performing as it should, take it to your local RadioShack  
store for assistance.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RF Emissions Information  
RF Emissions Information  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that  
to which the receiver is connected.  
Consult your local RadioShack store or an experienced radio/TV  
technician for help. If you cannot eliminate the interference, the FCC  
REQUIRESꢀTHATꢀYOUꢀSTOPꢀUSINGꢀYOURꢀPRODUCTꢃꢀ#HANGESꢀORꢀMODIÞCATIONSꢀ  
not expressly approved by RadioShack may cause interference and  
void the users authority to operate the equipment.  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) this device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
7ARNINGSꢁ  
Any adjustment to this equipment is recommended to be  
performed by or under the immediate supervision and responsibility  
OFꢀAꢀPERSONꢀCERTIÞEDꢀASꢀTECHNICALLYꢀQUALIÞEDꢀTOꢀPERFORMꢀTRANSMITTERꢀ  
maintenance and repair duties in the private land mobile services  
ANDꢀÞXEDꢀSERVICESꢀBYꢀANꢀORGANIZATIONꢀORꢀCOMMITTEEꢀREPRESENTATIVEꢀOFꢀ  
users of those services.  
Replacement of any transmitter component (crystal, semiconductor,  
etc.) for this equipment could result in violation of FCC rules.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do Stuff  
Do Stuff  
Do more with your CB radio.  
25-watt, 39” Whip,  
Magnetic-mount  
Mobile CB Antenna  
-INIŸ%XTENSIONŸ3PEAKERŸ  
Receive more, and  
Transmit farther in  
your car.  
Clip it to your visor.  
Set it on your dash.  
13.8VDC 3-Amp Power Supply  
Power up in your home.  
DC Power Cord  
Power up in your car.  
ꢂꢃꢄꢅ7ATTŸ!MPLIÚEDŸ-OBILEŸ  
%XTENSIONŸ3PEAKER  
ꢄꢅ7ATTŸ(EAVYꢅDUTYŸ%XTENSIONŸ  
Speaker  
Amplify over loud noises.  
Amplify at home or in the  
car.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Warranty  
This product is warranted by Rad ioShack against manufacturing defects in material  
and workmanship under normal use for one (1) year from the date of purchase  
from Rad ioShack company-owned stores and authorized Rad ioShack franchisees  
and dealers. EXCEPT AS PROVIDED HEREIN, Rad ioShack MAKES NO EXPRESS  
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES  
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Rad ioShack SHALL HAVE  
NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR  
ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY  
OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING  
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO,  
ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA,  
PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR  
CONSEQUENTIAL DAMAGES, EVEN IF Rad ioShack HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or  
the exclusion or limitation of incidental or consequential damages, so the above  
limitations or exclusions may not apply to you.  
In the event of a product defect during the warranty period, take the product  
and the Rad ioShack sales receipt as proof of purchase date to any Rad ioShack  
store. Rad ioShack will, at its option, unless otherwise provided by law: (a) correct  
the defect by product repair without charge for parts and labor; (b) replace the  
product with one of the same or similar design; or (c) refund the purchase price. All  
replaced parts and products, and products on which a refund is made, become the  
property of Rad ioShack. New or reconditioned parts and products may be used in  
the performance of warranty service. Repaired or replaced parts and products are  
warranted for the remainder of the original warranty period. You will be charged for  
repair or replacement of the product made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to  
acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow  
instructions, improper installation or maintenance, alteration, lightning or other  
incidence of excess voltage or current; (b) any repairs other than those provided by a  
Rad ioShack Authorized Service Facility; (c) consumables such as fuses or batteries;  
(d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of  
product removal, installation, set-up service adjustment or reinstallation.  
4HISꢀWARRANTYꢀGIVESꢀYOUꢀSPECIÞCꢀLEGALꢀRIGHTSꢄꢀANDꢀYOUꢀMAYꢀALSOꢀHAVEꢀOTHERꢀRIGHTSꢀWHICHꢀ  
vary from state to state.  
Rad ioShack Customer Relations  
300 RadioShack Circle, Fort Worth, TX 76102  
12/99  
Protect the environment by recycling used electronics.  
Go to www.ecyclingcentral.comŸTOŸÚNDŸAŸRECYCLEŸLOCATIONŸNEARŸYOUꢀ  
04A08  
©2008. RadioShack Corporation.  
21-1679  
AO0300ABA1  
Printed in China  
All rights reserved. RadioShack and RadioShack.com  
are trademarks used by RadioShack Corporation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Telephone Accessories CE 135 User Guide
Ramsey Electronics Satellite Radio RRW1A User Guide
RIDGID Cordless Saw MS 1065LZ User Guide
Roland Musical Instrument GW 7 User Guide
Ryobi Sander RS290 User Guide
Samsung All in One Printer SCX 4720F User Guide
Samsung Flat Panel Television 32LB5600 User Guide
Sapphire Audio Digital Camera Speed camera User Guide
Seagate Computer Drive STBL320100 User Guide
Sears Battery Charger 20071211 User Guide