49-820.fm Page 1 Thursday, August 19, 1999 10:29 AM
Cat. No. 49-820
OWNER’S MANUAL
RS-2000 Auto Security Alarm System
Please read this entire manual before you begin installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 3 Thursday, August 19, 1999 10:29 AM
Violation Confirmation — beeps
three times when you disarm the sys-
tem after the alert has sounded, to let
you know what happened while you
were away from the vehicle.
FCC INFORMATION
Your alarm system might cause TV or
radio interference even when it is op-
erating properly. To determine wheth-
er your system is causing the
interference, move your vehicle out of
the area. If the interference goes
away, your alarm system was caus-
ing it. Try to eliminate the interference
by:
Programmable Options — let you
customize several of your alarm’s op-
tions, such as shock sensor sensitivi-
ty and the valet mode.
Computer-Controlled Fan Sensor
— can tell the difference between
your vehicle’s dome or trunk light and
an electric cooling fan (which can
make other alarms sound a false
alert) without using additional wiring.
• Keeping your system away from
the receiver
• Contacting
your
local
Ra-
dioShack store for help
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your alarm system.
Toll-Free Help — if you have any
questions about or problems with
your alarm system, just call:
1-800-598-2527
Warning: Your alarm system’s alerts
are painfully loud. Take care during
installation to keep your head away
from the system once you connect
power.
Need Help? Call 1-800-598-2527
3
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 4 Thursday, August 19, 1999 10:29 AM
CONTENTS
Installing the System ..................................................................................... 5
Supplied Items ........................................................................................... 5
Installation Order ....................................................................................... 6
Connecting the System to Power .............................................................. 6
Activating the Remote Controls ................................................................. 6
Mounting the System ................................................................................. 7
Installing the Status Indicator .................................................................... 8
Using the Alarm System ................................................................................ 9
Arming the Alarm ....................................................................................... 9
Temporarily Reducing the Shock Sensor’s Sensitivity ........................ 9
Sounding the Panic Alarm ......................................................................... 9
Alarm Violations ......................................................................................... 9
Disarming the System ............................................................................. 10
Using the Car Finder ............................................................................... 10
Setting the System’s Options .................................................................. 10
Setting the Shock Sensor’s Sensitivity .............................................. 10
Setting the Current Sensor ................................................................ 11
Setting the Valet Mode (Passive Arming/Disarming) ......................... 11
Troubleshooting ........................................................................................... 12
Care and Maintenance ................................................................................. 14
Replacing the Fuse .................................................................................. 15
Replacing a Remote Control’s Battery .................................................... 15
Specifications ............................................................................................... 16
4
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 5 Thursday, August 19, 1999 10:29 AM
INSTALLING THE SYSTEM
SUPPLIED ITEMS
Your alarm system includes these items:
Two Four-Button Remotes
Main System
Mounting Screws
Status Indicator with Bracket and Harness
Double-Sided Tape
Need Help? Call 1-800-598-2527
5
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 6 Thursday, August 19, 1999 10:29 AM
INSTALLATION ORDER
ACTIVATING THE
REMOTE CONTROLS
You can install your system in just
four easy steps:
You must train the system to respond
to the supplied remote controls. To
activate both remote controls, imme-
diately after applying power, press
1. Connect the system to power.
2. Train the remote controls.
3. Mount the system.
DISARM
on one of the remotes. The
system beeps twice.
4. Install the status indicator.
If the system loses power, it stops re-
sponding to both remotes. Simply
CONNECTING THE
SYSTEM TO POWER
DISARM
press
on one of the remotes
after power is restored to reactivate
them.
Warning: We recommend that you
muffle the alarm’s speaker before you
connect the system to power. The
alarm is extremely loud.
Both of the supplied system remotes
share the same remote code, but
your system can learn two remote
codes if you want to add another re-
mote control (RadioShack Cat. No.
49-845). To activate a second remote
control code, be sure the system is
Follow these steps to connect the
system to power.
1. Connect the system’s red lead to
your vehicle battery’s positive (+)
terminal.
ARM
disarmed, then hold down
for 10
seconds. The system beeps three
times. Press any button on the new
remote to activate it.
2. Connect the system’s black lead
to a metal part of the vehicle’s
body that is not insulated from the
main chassis by any plastic part
or to the battery’s negative (–)
terminal. The system beeps three
times.
6
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 7 Thursday, August 19, 1999 10:29 AM
Once you select a location, follow
these steps to mount the system.
MOUNTING THE
SYSTEM
Select a location for your alarm sys-
tem in the engine compartment. For
the best results, the location should
meet the following conditions.
• All wires should reach their con-
nections without going near mov-
ing or hot engine parts.
Note: If necessary, you can
extend the wires using hook-up
wire and butt connectors. Use at
least 18-gauge wire and an insu-
lated wire connector to extend a
wire.
1. Hold the system against the
selected location and mark the
locations of the three mounting
holes.
• The mounting location should be
solid and have no mechanisms or
moving parts behind it.
1
2. Drill /8-inch holes at the marked
locations, taking care not to drill
into anything behind the mount-
ing surface.
• For the best remote range, the
mounting location should allow
the system’s yellow antenna wire
to hang straight down. Do not cut
or extend the wire — its length is
optimized for best operation.
3. Secure the system to the surface
using the supplied screws.
Note: For the best shock-sensor
operation, use all three screws.
• For the loudest siren, the siren
horn should point down toward
the pavement.
• The alarm should not point
straight up, as moisture could col-
lect in the siren horn and damage
the system.
• To prevent water damage, the
system should not be mounted in
a wheel well, directly behind the
radiator grill, or close to the
ground.
Need Help? Call 1-800-598-2527
7
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 8 Thursday, August 19, 1999 10:29 AM
bottom of the bracket. Then peel
off the adhesive backing from the
other side of the tape and press
the bracket onto the dash.
INSTALLING THE
STATUS INDICATOR
The alert indicator goes inside your
vehicle’s passenger compartment. Ei-
ther drill a mounting hole in a dash
panel or use the supplied mounting
bracket to hold the indicator. Follow
these steps to install the indicator.
If you are mounting the indica-
5
tor in the dash, drill a /16-inch
hole at the desired location.
3. Press the supplied grommet into
the mounting hole from the front
of the surface.
1. Locate an existing wire harness
that goes through your vehicle’s
firewall, and push the indicator
into the passenger compartment
through the existing hole.
Grommet
Indicator
If you cannot find an existing wire
harness, drill
a
1/4-inch hole
through the firewall into the pas-
senger compartment. Then push
the indicator through the hole.
4. Press the indicator into the grom-
met from the back of the surface.
Cautions:
• Before drilling, be sure you can
reach the other side of the
hole.
5. Plug the indicator’s harness into
the matching harness on the sys-
tem.
• Be sure you do not drill into
any mechanism on the other
side of the firewall.
6. Use the supplied wire tie to
secure the wire out of the way.
7. If you drilled a hole in the firewall,
use silicon sealant (not supplied)
to waterproof the hole.
• Protect the wire by placing a
rubber grommet (not supplied)
in the hole, and thread the wire
through the grommet.
2. If you are using the supplied
mounting bracket, use dena-
tured alcohol to clean the mount-
ing surface and let the surface
dry completely. Peel the backing
off of one side of the double-
sided tape and press it onto the
8
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 9 Thursday, August 19, 1999 10:29 AM
USING THE ALARM SYSTEM
When you disarm and re-arm the sys-
tem, the shock sensor returns to its
previous sensitivity setting.
ARMING THE ALARM
To arm the alarm, press ARM. The
alarm chirps once.
Notes:
SOUNDING THE PANIC
ALARM
• The status indicator turns on
when the system is armed.
To sound a panic alarm, press and
release PANIC. The alarm sounds
loud tones for 30 seconds. Press any
button to stop the panic alarm sooner.
• The system ignores current-
sensing violations for 40 sec-
onds after it arms.
• The system ignores shock-sen-
sor violations for 8 seconds after
you it arms.
ALARM VIOLATIONS
• If the valet mode is turned off, the
system arms 60 seconds after
you turn off your vehicle.
Your alarm senses violations by mon-
itoring your vehicle’s electrical system
(current sensing) and by detecting im-
pacts (shock sensing).
Temporarily Reducing the
Shock Sensor’s Sensitivity
An alert sounds immediately if the
current sensor detects an electrical
drain such as occurs when a dome or
trunk light turns on.
If you are parking in a severe weather
situation, near a construction zone, or
near heavy traffic, you can temporari-
ly reduce the system’s shock sensor
sensitivity to help prevent false alerts.
To reduce the sensitivity to half its
normal level, first press ARM to arm
the system. The alarm chirps once.
Then, within 2 seconds, press ARM
again. The alarm chirps once in a
lower tone.
The first time the alarm senses an im-
pact that exceeds its sensitivity level,
it chirps three times. If it senses an-
other impact within 30 seconds, the
system sounds a full alert.
If an impact is severe, a single
Note:
impact can cause a full alert to sound,
without giving a warning.
To completely turn off the shock sen-
sor, press ARM twice within 2 sec-
onds of arming. The alarm chirps in a
lower tone each time you press ARM.
When your alarm senses a violation,
it sounds extremely loud tones for 30
seconds and then re-arms. To silence
the alert sooner, press any button.
Need Help? Call 1-800-598-2527
9
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 10 Thursday, August 19, 1999 10:29 AM
Setting the Shock Sensor’s
Sensitivity
DISARMING THE
SYSTEM
The shock sensor’s initial setting is
fine for most situations. To test the
shock sensor, strike your vehicle on
the hood directly over the alarm.
To disarm the system, press DIS-
ARM. The system beeps twice to
confirm that it is disarmed.
Notes:
If the shock sensor is too sensitive or
not sensitive enough, follow these
steps to set it to a different level.
• The status indicator is off when
the system is disarmed.
• If the valet mode is turned off, the
system chirps and re-arms after
60 seconds if you have not
started the vehicle.
1. With the alarm disarmed, hold
FINDER
down
until the alarm
sounds four tones.
2. Within 2 seconds, strike your
vehicle with as much force as you
want the alarm to respond to. The
alarm sounds three tones. Any
shock equal to or greater than the
setting triggers the alert.
• If the system detected a violation
while you were away, it beeps
three times when you disarm it.
USING THE CAR FINDER
Notes:
The car finder helps you find your ve-
hicle in a dark or crowded parking lot.
To use the car finder, with the system
• If you do not strike your vehicle
within 2 seconds, the alarm is set
to its highest sensitivity. This
could cause frequent false alerts.
FINDER
armed, press
beeps 8 times.
. The alarm
• The shock sensor does not oper-
ate for 8 seconds after the sys-
tem arms.
SETTING THE SYSTEM’S
OPTIONS
You can adjust the following options:
• Shock Sensor Sensitivity
• Current Sensor (On/Off)
• Valet Mode (On/Off)
10
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 11 Thursday, August 19, 1999 10:29 AM
Setting the Current Sensor
Setting the Valet Mode
(Passive Arming/Disarming)
If your vehicle has electronic acces-
sories that turn on and off automati-
cally while you are away from the
vehicle, the alarm might sound false
alerts. (The system can detect an
electric engine fan, and does not
sound a false alert when the fan
comes on.)
The valet mode lets you leave your
vehicle for service or with a valet and
have it arm 60 seconds after you
not
turn off the engine. The default is for
the valet mode to be on (passive arm-
ing is off).
To have your system automatically
arm 60 seconds after you turn off the
To disable the current sensor so ac-
cessories will not trigger an alert, dis-
arm the system. Then hold down
PANIC for about 4 seconds. The sys-
tem beeps twice.
engine (this is called
),
passive arming
hold down DISARM for about 10 sec-
onds. The system beeps twice.
To turn on the valet mode (so the sys-
tem does not passively arm), hold
down DISARM again for about 10 sec-
onds. The system beeps three times.
To re-enable the current sensor, with
the system disarmed, hold down PAN-
IC for about 4 seconds. The system
beeps once.
Notes:
• The current sensor does not
operate for 40 seconds after the
system arms.
• You can also try unplugging or
disconnecting electronic acces-
sories such as radar detectors or
cellular phones when you leave
your vehicle, instead of disabling
the current sensor, to prevent the
false alerts.
Need Help? Call 1-800-598-2527
11
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 12 Thursday, August 19, 1999 10:29 AM
TROUBLESHOOTING
This section describes some problems you might encounter, and gives possible
solutions.
Problem
Possible Solution
Frequent false alerts
• Another accessory is triggering the alarm. Try
turning off current sensing to see if this solves the
problem. If it does, try turning it back on, then
removing other accessories, one by one, until
you find which accessory is triggering the false
alert. If possible, turn off that accessory when you
leave your vehicle. Common problem accesso-
ries are cellular phones, radar detectors, and
vehicle self-test systems. If you cannot turn off
the accessory, leave current sensing disabled.
Your alarm can tell the difference between
Note:
the vehicle’s electric fan and other accessories,
so the fan does not trigger a false alert if the fan
turns on while the system is armed.
• Your alarm’s electrical connections are not mak-
ing good contact. Check the connections and, if
necessary, connect the power and ground leads
to the vehicle’s battery terminals.
• The shock sensor is too sensitive. See “Setting
the Shock Sensor’s Sensitivity” on Page 10 to
change the sensor’s setting.
• Loud thunderclaps and heavy machinery can
trigger a false alarm. If you know a thunderstorm
is approaching or that heavy machinery will be
used nearby you can temporarily reduce the
shock sensor’s sensitivity or turn it off entirely.
See “Temporarily Reducing the Shock Sensor’s
Sensitivity” on Page 9.
The alarm is not loud
enough
• The siren is being muffled by the engine or hood.
Try repositioning the siren so it points to the
pavement.
12
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 13 Thursday, August 19, 1999 10:29 AM
Problem
Possible Solution
Alarm does not operate • Check all power connections.
• Check the system’s fuse. If it has blown, see
“Replacing the Fuse” on Page 15.
• Check the remote control’s battery. See “Replac-
ing a Remote Control’s Battery” on Page 15.
Alarm does not sound
when it should
• The shock sensor is not sensitive enough. See
“Setting the Shock Sensor’s Sensitivity” on
Page 10. If you set the shock sensor to its maxi-
mum sensitivity and the alarm still does not
sound, confirm that you mounted the alarm on a
solid, metal vehicle part (not on the frame or on
rubber or plastic parts). If necessary, reposition
the alarm for better performance.
• If you have a large vehicle, the shock sensor
might not detect impacts on parts of the vehicle
far from the system. Remember that most thieves
break into your vehicle through one of the front
doors or windows. If you set the system sensitive
enough to detect all impacts, you might experi-
ence frequent and annoying false alarms.
• Confirm that you have not accidently disabled
current sensing. See “Setting the Current Sen-
sor” on Page 11.
The remote control’s
range is poor
• The antenna wire is too close to metal. If possi-
ble, position the yellow antenna wire away from
metal.
• The antenna wire has been cut or extended. The
antenna wire is factory tuned for the best perfor-
mance (a longer antenna will actually not work as
well as the short included antenna wire). If the
wire has been cut, take the system to your local
RadioShack store for repair service.
Need Help? Call 1-800-598-2527
13
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 14 Thursday, August 19, 1999 10:29 AM
CARE AND MAINTENANCE
Your RadioShack RS-2000 Auto Security Alarm System is an example of supe-
rior design and craftsmanship. The following suggestions will help you care for
the alarm so you can enjoy its protection for years.
Keep the remote controls dry. If they get wet, wipe them dry im-
mediately. Liquids can contain minerals that might corrode the
electronic circuits.
Handle the alarm and remotes gently and carefully. Dropping
them can damage circuit boards and cases and might make the
remotes work improperly.
Use and store the remote controls only in normal temperature en-
vironments. Temperature extremes can shorten the life of elec-
tronic devices, damage batteries, and distort or melt plastic parts.
Keep the remote controls away from dust and dirt, which can
cause premature wear of parts.
Do not use harsh chemicals, cleaning solvents, or strong deter-
CLEANER
gents to clean the alarm.
Use only fresh batteries of the recommended size and type in
your remote controls. Old or weak batteries can leak chemicals
that can damage your system’s internal circuits.
Modifying or tampering with your alarm’s internal components can cause a mal-
function and might invalidate the alarm’s warranty and void your FCC authoriza-
tion to operate it. If your alarm is not operating as it should, take it to your local
RadioShack store for assistance.
14
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 15 Thursday, August 19, 1999 10:29 AM
REPLACING THE FUSE
REPLACING A REMOTE
CONTROL’S BATTERY
Follow these steps to check the sys-
tem’s fuse and replace it if it has
blown. The system uses a 5-amp 11/4
If either remote control’s range is re-
duced or if the indicator does not light
when you press a button, replace its
battery. The remote controls each
use a 12-volt remote control battery
(Cat. No. 23-144). Follow these steps
to replace the battery.
×
1/4-inch fast-acting fuse (Ra-
dioShack Cat. No. 270-1011).
1. Push together the two halves of
the inline fuse holder (on the red
power wire) and twist them to
separate the halves.
2. Inspect the fuse. If the wire is bro-
ken or missing, replace it.
Caution: Use only a fuse of the
same type and rating. Using a dif-
ferent type of fuse or bypassing
the fuse protection can damage
your alarm or your vehicle’s elec-
trical system.
1. Snap apart the remote control’s
case.
3. Put the new fuse in the holder
and push and twist the holder’s
halves together.
Caution: Take care not to lose
any of the remote control’s
pieces.
2. Replace the battery with a new
one.
3. Put all parts back in place and
snap the case halves back
together.
Need Help? Call 1-800-598-2527
15
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 16 Thursday, August 19, 1999 10:29 AM
SPECIFICATIONS
Siren Sound Level ................................................. More than 115 dB at 1 Meter
Current Drain .......................................................................... 22 mA (Standby)
1 Amp (Siren Sounding)
Power Requirements .................................................................. 9–16 Volts DC
Alarm Weight ........................................................................................ 1 lb, 8 oz
Remote Carrier Frequency ........................................................... 303.875 MHz
RF Output Power ................................................................ 5,580 µV at 1 Meter
Remote Control Power .................................................. 12-Volt Alkaline Battery
Remote Weight ..........................................................................................1.5 oz
Specifications are typical; individual units might vary. Specifications are subject
to change and improvement without notice.
16
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 17 Thursday, August 19, 1999 10:29 AM
NOTES
Need Help? Call 1-800-598-2527
17
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 18 Thursday, August 19, 1999 10:29 AM
18
Need Help? Call 1-800-598-2527
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 19 Thursday, August 19, 1999 10:29 AM
Need Help? Call 1-800-598-2527
19
Download from Www.Somanuals.com. All Manuals Search And Download.
49-820.fm Page 20 Thursday, August 19, 1999 10:29 AM
RadioShack Limited Warranty
This security product is warranted against manufacturing defects in material and work-
manship for ninety (90) days from the date of purchase from RadioShack company
owned stores and authorized RadioShack franchisees and dealers. Within this period
RadioShack will repair the security product without charge for parts and labor. Simply
bring your RadioShack sales slip as proof-of-purchase date to any RadioShack
store.
This warranty does not cover damage or failure caused by or attributable to Acts of
God, abuse, misuse, improper or abnormal usage, faulty installation, improper mainte-
nance, lightning or other incidence of excess voltage, or any repairs other than those
provided by a RadioShack Authorized Service Facility, or transportation costs.
RadioShack is not responsible or liable for indirect, special, or consequential
damages arising out of or in connection with the use or performance of the prod-
uct or other damages with respect to loss of property, loss of revenues or profit,
or costs of removal, installation or reinstallation.
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES
AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION
OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states do
not allow the limitation or exclusion of incidental or consequential damages and some
states do not allow limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser. There will be charges ren-
dered for repairs to the product made after the expiration of the aforesaid ninety (90)
day warranty period.
This warranty gives you specific legal rights and you may have other rights which vary from state to
state.
We Service What We Sell
10/95
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
9/96
Printed in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|