49-118
Thank you for purchasing your Door/Window
Alarm from RadioShack. Please read this user’s
guide before installing, setting up and using
your new door/window alarm.
Wireless · Key-Lock
DOOR/WINDOW ALARM
Using Your Alarm
What’s Included
Instant Activation
LED
Alarm
Magnet
1. Slide INSTANT/DELAY switch to INSTANT.
Key (2)
Screw (4)
Drilling Template
Actual product may vary from the images
found in this document.
Adhesive Strip (3)
Anchor (4)
User’s Guide
2. Insert key and rotate to ON.
Alarm
3. If you move the magnet away from the alarm, it sounds for
about 90 seconds. Then, the alarm turns off and the LED
flashes green. Turn the key to OFF if you want to silence the alarm immediately.
Adhesive Strip (3)
Magnet
Delay Activation
Battery Notes:
1. Slide INSTANT/DELAY switch to DELAY.
•
•
•
Dispose of old batteries promptly and
properly. Do not burn or bury them.
2. Insert key and rotate to ON. The LED lights green and you have 15 seconds to
leave and close the door. After 15 seconds, the alarm arms and the LED turns off.
Use only fresh batteries of the required
size and recommended type.
Deactivation
Do not mix old and new batteries,
different types of batteries (standard,
alkaline, or rechargeable), or rechargeable
batteries of different capacities.
1. When you return home and open the door, the LED lights red and you have 10 - 15
seconds to turn off the alarm.
2. Turn the key to OFF to disarm. If you do not disarm it, the alarm sounds for 90
seconds.
•
If you do not plan to use the alarm for
a month or more, remove the batteries.
Batteries can leak chemicals that can
destroy electronic parts.
Anchor (4)
Screw (4)
3. If the alarm was triggered while you were away, the LED alternately flashes green
and red after the alarm has sounded for 90 seconds.
Keys
Setting Up Your Alarm
Choosing a Location
Mounting Your Alarm Using Screws
Mounting the Magnet
Installing Batteries
1. Align the triangle on the magnet with the
engraved line on the left or right side of the
alarm.
1. Use the supplied drilling template to mark
the mounting screw location.
2. Drill two 1/16 - inch (2 mm) holes.
3. Insert the top screw, leaving about 1/8 - inch
(3 mm) to engage the keyhole on the alarm.
1. Use a small, flat bladed screwdriver to
remove the mounting plate from the magnet.
1. Remove the screw on the bottom of your
alarm and lift the battery compartment cover.
2. Use the supplied screws or adhesive strips
to secure the mounting plate to the selected
surface. Do not use both strip and screws.
2. Insert two AAA
batteries (not
2. Place the magnet edge no more than
5
/
16 - inch (8 mm) from the alarm.
supplied), as indicated
by the polarity
symbols (+ and -)
marked inside.
3. Mount the alarm to a door or window and
the magnet to the door or window frame
using the supplied adhesive strips or screws.
3. Connect magnet to mounting plate.
4. Install the alarm over the top screw.
5. Slide off the battery cover.
Magnet (Rear View)
3. Replace the cover.
6. Insert the lower screw through the hole inside
the battery compartment.
Mounting
Plate
4. Replace the batteries if the alarm sound
weakens or the LED flashes red. If the alarm
does not work after you replace the batteries,
remove and reinstall them.
Battery
Cover
Drilling
Template
Apply to frame
5
/16 “ max
©2007. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
09A07
49-118
Printed in China
|