43-1095.fm Page 1 Tuesday, August 17, 1999 3:37 PM
Cat. No. 43-1095
OWNER’S MANUAL
Please read before using this equipment.
ET-925
900 MHz Dual Keypad
Cordless Speakerphone
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 3 Tuesday, August 17, 1999 3:37 PM
Auto Talk — you can answer a call by
just lifting the handset from the base.
Warning: To reduce the risk of fire
or shock hazard, do not expose
this product to rain or moisture.
Hearing-Aid Compatibility — lets
you use your phone with hearing aids
that have a T (telephone) switch.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
Important Note: Cordless phones
such as this one require AC power to
operate. When the AC power is off,
you cannot dial out or receive incoming
calls using your ET-925. To be safe,
you should also have a phone that
does not need AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an
AC power failure.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
!
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
Serial Number __________________
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 4 Tuesday, August 17, 1999 3:37 PM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
This telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC Registration Number
and the REN to your phone company.
These numbers are on the bottom of
the base.
Each device that you connect to the
phone line draws power from the phone
line. We refer to this power draw as the
device’s ringer equivalence number, or
REN. The REN is on the bottom of the
base.
Note: You must not connect your
phone to any of the following:
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five, your
phones might not ring. In rural areas, a
total REN of three might impair ringer
operation. If ringer operation is im-
paired, remove a device from the line.
• coin-operated systems
• party-line systems
• most electronic key phone sys-
tems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 5 Tuesday, August 17, 1999 3:37 PM
CONTENTS
Installation ............................................................................................................... 6
Selecting a Location ........................................................................................... 6
Placing the Base on a Desk Top .................................................................. 6
Mounting the Base on a Wall Plate .............................................................. 7
Mounting the Base Directly on the Wall ....................................................... 8
Connecting and Charging the Battery Pack ..................................................... 10
Setting the Dialing Mode .................................................................................. 11
Setting the Ringer ............................................................................................ 12
On the Handset ......................................................................................... 12
On the Base ............................................................................................... 12
Using a Headset ............................................................................................... 12
Operation ............................................................................................................... 14
Making and Receiving Calls ............................................................................. 14
Using the Handset ..................................................................................... 14
Using the Speakerphone ........................................................................... 14
Switching Between the Handset and Speakerphone ................................ 15
Using Both the Handset and Speakerphone ............................................. 15
Changing the Channel ............................................................................... 15
Using Mute ....................................................................................................... 15
Using Redial ..................................................................................................... 16
Using Flash ...................................................................................................... 16
Using Tone Services on a Pulse Line ............................................................... 16
Paging .............................................................................................................. 17
Memory Dialing ................................................................................................ 17
Storing a Number in Memory ..................................................................... 17
Entering a Pause ....................................................................................... 18
Dialing a Memory Number ......................................................................... 19
Chain-Dialing Service Numbers ................................................................. 19
Testing Stored Emergency Numbers ......................................................... 19
Troubleshooting ................................................................................................... 20
Care and Maintenance ......................................................................................... 22
Replacing the Battery Pack .............................................................................. 23
The FCC Wants You to Know .......................................................................... 24
Lightning ........................................................................................................... 24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 6 Tuesday, August 17, 1999 3:37 PM
INSTALLATION
Placing the Base on a
Desk Top
SELECTING A
LOCATION
Follow these steps when you place the
base on a desk, shelf, or table.
You can place the ET-925’s base on a
desk top or table, or mount it on a wall.
Select a location that is:
1. Plug one end of the supplied long
modular cord into the TEL LINE
jack on the back of the base.
• near an AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls
or filing cabinets, wireless inter-
coms, alarms, and room monitors
• away from other cordless phones
2. Plug the modular cord’s other end
into a modular phone line jack.
The base’s location affects the hand-
set’s range. If you have a choice of
several locations, try each to see
which provides the best performance.
Caution: The supplied RadioShack
AC adapter was designed specifically
for your ET-925. Use only the supplied
adapter.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
Notes:
• Your telephone connects directly
to a modular telephone line jack. If
your phone line jack is not a mod-
ular jack, you can update the wir-
ing yourself, using jacks and
adapters available at your local
RadioShack store. Or, you can let
the phone company update the
wiring for you.
• The USOC number of the jack to
be installed is RJ11C (RJ11W if
you want to mount it on a wall
plate).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 7 Tuesday, August 17, 1999 3:37 PM
4. Route the adapter’s cord through
the strain relief slot on the base.
2. Route the modular cord through
the upper groove on the bottom of
the base.
Strain Relief
Slot
Upper
Groove
5. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
6. Lift the base’s antenna to a verti-
cal position.
Mounting the Base on a
Wall Plate
1. Plug one end of the supplied short
modular cord into the TEL LINE
jack on the back of the base.
4. Route the adapter’s cord through
the right side of the strain relief
slot on top of the base and
through both the upper and lower
grooves on the bottom of the
base.
Strain Relief
Slot
Upper
Groove
Lower
Groove
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 8 Tuesday, August 17, 1999 3:37 PM
5. Plug the short modular cord into
the wall plate jack, press the ex-
cess cord into the slot in the cen-
ter of the base, then align the
base’s keyhole slots with the wall
plate studs and slide the base
downward to secure it.
Mounting the Base Directly
on the Wall
For this mounting method, you need
two flat-head wood screws (not sup-
plied) with heads that fit into the key-
hole slots on the bottom of the base.
1. Drill two holes 35/16
inches apart. Then
thread a screw into
each hole, letting the
heads extend about
3/16 inch from the
wall.
3/16
Slot for
Excess
Cord
5
16
3 /
6. Press and lift out the handset
holder, turn it over and rotate it
180°, then snap it back into place
so it holds the handset.
2. Plug one end of the supplied long
modular cord into the TEL LINE
jack on the back of the base.
3. Route the modular cord through
the upper and lower grooves on
the bottom of the base.
7. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
Upper
Groove
Lower
Groove
8. Lift the base’s antenna to a verti-
cal position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 9 Tuesday, August 17, 1999 3:37 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
7. Plug the modular cord into a mod-
ular phone line jack.
8. Press and lift out the handset
holder, rotate it 180°, then snap it
back into place so it holds the
handset.
5. Route the adapter’s cord through
the right side of the strain relief
slot on top of the base and
through both the upper and lower
grooves on the bottom of the
base.
Strain Relief
Slot
Upper
Groove
Lower
Groove
6. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.
9. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
10. Lift the base’s antenna to a verti-
cal position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 10 Tuesday, August 17, 1999 3:37 PM
CONNECTING AND
CHARGING THE
BATTERY PACK
The ET-925 comes with a recharge-
able nickel-cadmium battery pack in
the handset. Before using your phone,
you must connect the battery pack and
then charge it for about 14 hours.
CHARGE Indicator
1. Remove the screw on the battery
compartment cover, then press
down and slide the cover in the di-
rection of the arrow to remove it.
Recharge the battery pack when the
handset beeps and the TALK/BATT
LOW indicator flashes during a call.
Notes:
• If the CHARGE indicator does not
light when you place the handset
on the base, be sure the battery
pack and AC adapter are correctly
and securely connected. Be sure
the charging contacts on the
handset and the base are making
contact.
2. Plug the battery pack’s connector
into the socket in the compart-
ment. The connector fits only one
way.
Also, check the charging contacts
on the handset and the base. If
the contacts are dirty or tarnished,
clean them with a pencil eraser.
3. Replace the cover, then reinsert
and tighten the screw.
To charge the battery pack, simply
place the handset on the base.
The CHARGE indicator on the base
lights.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 11 Tuesday, August 17, 1999 3:37 PM
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work
and you might hear an error tone.
If this happens, return the handset
to the base for a few seconds.
SETTING THE DIALING
MODE
DIAL MODE
Set
on the back of the base
for the type of service you have. If you
are not sure which type you have, do
this test.
• If the battery pack loses its charge
completely or the base loses pow-
er while the handset is away from
it, the security access-protection
code needs to be reset. To reset
the security code, place the hand-
set on the base. If it was the hand-
set that lost power, leave the
handset on the base to charge the
battery pack.
DIAL MODE
T
to .
1. Set
SPEAKER
2. Press
and listen for a
dial tone from the speakerphone.
The IN USE indicator turns on.
• About once a month, fully dis-
charge the battery pack by keep-
ing the handset off the base until
the TALK/BATT LOW indicator
flashes. Otherwise, the battery
pack loses its ability to fully re-
charge.
0
3. Press any number other than .
Note: If your phone system re-
quires that you dial an access
code ( , for example) before you
dial an outside number, do not
press the access code either.
9
• If the TALK/BATT LOW indicator
does not light and the phone does
not work, recharge the battery
pack. (The battery power might be
too low to light the indicator.)
If the dial tone stops, you have
DIAL
touch-tone service. Leave
MODE
T
set to .
If the dial tone continues, you
DIAL
have pulse service. Set
• The supplied battery pack should
last for about a year. When the
battery pack loses its ability to ful-
ly recharge, order a replacement
battery pack from your local Ra-
dioShack store (see “Replacing
the Battery Pack” on Page 23).
MODE
P
to .
SPEAKER
4. Press
again. The IN
USE indicator turns off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 12 Tuesday, August 17, 1999 3:37 PM
On the Base
SETTING THE RINGER
RINGER
The
ringer on the base. To turn off the ring-
RINGER
setting affects only the
On the Handset
er on the base, set
OFF
on the back
The ringer on the handset is turned on
whenever the handset is off the base.
You can select one of four different
ringer tone/volume settings on the
handset while the phone is not in use.
of the base to
.
VOLUME
Press
to hear the current
ringer setting.
To turn on the ringer on the base, set
RINGER LO HI
to either
or as desired.
When you place the handset on the
RINGER OFF
base and set
to
, the ET-
925 does not ring when it receives a
call. However, other phones connect-
ed to the same phone line still ring.
VOLUME
Repeatedly press
until you
USING A HEADSET
hear the desired ringer setting. Each
VOLUME
time you press
changes in this order:
, the ringer
You can make or answer calls with
hands-free convenience using an op-
tional headset that has a 3/32-inch (2.5
mm) plug. We recommend Ra-
dioShack Cat. No. 43-194, which is
specially designed for use with the ET-
925.
High-volume, high-pitch
Low-volume, high-pitch
High-volume, low-pitch
Low-volume, low-pitch
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 13 Tuesday, August 17, 1999 3:37 PM
To connect the headset, pull open the
rubber cover marked
on the side of
the handset, then insert the headset’s
3/32-inch (2.5 mm) plug into the jack.
Notes:
• Connecting a headset discon-
nects the handset’s earpiece and
microphone.
• You can still use the speaker-
phone after connecting a headset.
VOLUME
•
on the handset also con-
trols the connected headset’s vol-
ume.
• If you place the handset on the
base to recharge it while the
headset is connected, be sure the
handset seats properly.
With a headset connected, you can
make or answer calls as usual using
the keys on the handset.
When you finish using the headset,
disconnect it from the handset and
close the rubber cover to protect the
jack.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 14 Tuesday, August 17, 1999 3:37 PM
OPERATION
Note: To use the speakerphone, you
must use the base keypad; to use the
handset, you must use the handset
keypad.
Using the Speakerphone
To make or answer a call using the
speakerphone, simply press SPEAK-
ER. The IN USE indicator lights on the
base. Use the base’s keypad to dial
the desired number.
MAKING AND
RECEIVING CALLS
Using the Handset
To make or answer a call, simply lift
the handset. Or, if the handset is not
on the base, press TALK. The TALK/
BATT LOW indicator on the handset
and the IN USE indicator on the base
light. Use the handset keypad to dial
the desired number.
IN USE Indicator
SPEAKER
Slide VOLUME on the right side of the
base to adjust the speakerphone’s vol-
ume.
Repeatedly press VOLUME on the
handset to adjust the volume of the call
as you like.
To end a speakerphone call, simply
press SPEAKER again. The IN USE in-
dicator turns off.
To end a call, place the handset on the
base or press the handset’s TALK but-
ton. The TALK/BATT LOW and IN
USE indicators turn off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 15 Tuesday, August 17, 1999 3:37 PM
Switching Between the
Changing the Channel
Handset and Speakerphone
If you notice interference, static, or
noise during a call, you can press CH
(channel) to find a clearer channel.
To switch to the speakerphone while
you are using the handset, press
SPEAKER on the base. When you
hear the conversation or the dial tone
on the speakerphone, press TALK on
the handset or place the handset on
the base.
To switch to the handset while you are
using the speakerphone, simply lift the
handset off the base or press TALK,
then press SPEAKER.
The ET-925 changes to a different
channel each time you press CH.
Using Both the Handset and
Speakerphone
Note: If the handset is too far from the
base, the channel might not change.
Move closer to the base and try again.
If you are using the speakerphone,
someone else can press TALK on the
handset and join the conversation.
If you are using the handset, one or
more people can join the conversation
by pressing SPEAKER on the base.
USING MUTE
While talking on the speakerphone,
you can temporarily mute the ET-
925’s microphone by pressing MUTE
so the other party cannot hear you. To
return to the call, press MUTE again,
or press SPEAKER.
During the call, one of you can hang
up and let the call continue at the oth-
er keypad. Or, you can both hang up
at the same time to end the call.
Note: If you hear a high-pitched noise
from the base’s speaker, the handset
and the base are too close together.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 16 Tuesday, August 17, 1999 3:37 PM
USING REDIAL
USING FLASH
FLASH
You can quickly dial the last number di-
aled. When you hear the dial tone, sim-
performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
REDIAL
ply press
on the base (or
REDIAL/P
on the handset).
For example, if you have Call Waiting,
FLASH
press
to answer an incoming
Notes:
call without disconnecting the current
• The redial memory is separate for
each keypad. You cannot redial a
number you dialed on the handset
FLASH
call. Press
first call.
again to return to the
REDIAL
keypad using
on the base
Note: If you do not have any special
FLASH
keypad, and vice versa.
phone services, pressing
disconnect the current call.
might
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
USING TONE SERVICES
ON A PULSE LINE
• The redial memory also holds
pause entries. See “Entering a
Pause” on Page 18.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow-
ing these steps.
• The redial memory does not store
a flash entry or any digits you
FLASH
press after
Flash”).
(see “Using
DIAL MODE
P
1. Be sure
is set to .
2. Dial the service’s main number.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 17 Tuesday, August 17, 1999 3:37 PM
3. When the service answers, press
TONE/ . Any additional numbers
you dial are sent as tone signals.
Notes:
• Make sure you press TALK or
SPEAKER twice to stop the hand-
set from beeping. If you press
TALK or SPEAKER only once, you
get a dial tone.
• If you press PAGE for less than 2
seconds, the handset beeps for
only 2 seconds.
4. After you complete the call, return
the handset to the base, press
TALK, or press SPEAKER. The
phone automatically resets to the
pulse mode.
• If you receive a call while the page
is sounding, the handset stops
beeping and the handset and base
start ringing.
PAGING
MEMORY DIALING
To page the person who has the hand-
set or to locate the handset when the
phone is not in use, hold down PAGE on
the base for at least 2 seconds. The
handset beeps for 1 minute. To stop it
from beeping before it automatically
stops, press TALK on the handset (or
SPEAKER on the base) twice.
You can store up to 20 numbers in the
ET-925’s memory (10 in the handset’s
memory and another 10 in the base’s
memory), then dial a stored number by
pressing MEM then a one-digit memory
location number.
Storing a Number in Memory
Notes:
• The phone beeps 5 times and exits
the programming mode if you wait
more than 20 seconds between
key presses.
• You cannot dial the number stored
in one memory (base or handset)
using the keypad on the other.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 18 Tuesday, August 17, 1999 3:37 PM
1. Press MEM on the handset or the
base. The TALK/BATT LOW or IN
USE indicator blinks.
later.) Then attach the sticker to
the phone.
If you hear a dial tone when
Note:
you pick up the handset, press
TALK to turn it off before pressing
MEM.
2. Enter the number (up to 16 digits)
To clear a stored number, simply store
a new number in its place. Or, press
MEM twice. Then press the memory lo-
cation number (0–9) you want to clear.
A tone sounds.
and any TONE/
mode changes
or pause entries (see “Using Tone
Services on a Pulse Line” on
Page 16 or “Entering a Pause”).
Notes:
If you hear a dial tone when you
pick up the handset, press TALK to turn
it off before pressing MEM twice.
Note:
• Each TONE/
or pause entry
uses one digit of memory.
• If you try to enter more than 16
digits, the phone beeps 5 times
and exits the programming
mode. Start over at Step 1.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example)
and wait for a second dial tone before
you can dial an outside number. You
can store the access code with the
phone number. However, you must
also store a pause after the access
code to allow the outside line time to
connect. To enter a 2-second pause,
press REDIAL/P (or REDIAL on the
base). For a longer pause, press REDI-
AL/P (or REDIAL on the base) addition-
al times.
3. Press MEM again, then enter the
memory location number (0–9)
where you want to store the num-
ber. A tone sounds to indicate that
the number is stored.
4. For each stored number, write the
person’s or company’s name next
to the appropriate location number
on the supplied MEMORY directo-
ry sticker. (Use a pencil in case
you need to change the number
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 19 Tuesday, August 17, 1999 3:37 PM
Dialing a Memory Number
Testing Stored Emergency
Numbers
To dial a number stored in the handset’s
memory, lift the handset from the base
or press TALK. When you hear the dial
tone, simply press MEM and enter the
memory location number for the number
you want to dial.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
To dial a number stored in the base’s
memory, press SPEAKER. When you
hear a dial tone, simply press MEM and
enter the memory location number for
the number you want to dial.
Note: If you select an empty memory lo-
cation, the phone beeps 5 times. Try
again.
Chain-Dialing Service
Numbers
For quick recall of numbers for special
services (such as alternate long dis-
tance or bank by phone), store each
group of numbers in its own memory lo-
cation.
Dial the service’s main number first.
Then, at the appropriate place in the
call, press MEM and the number for the
location where the additional informa-
tion is stored.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 20 Tuesday, August 17, 1999 3:37 PM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the follow-
ing suggestions might help.
Problem
Suggestion
Low volume or unusual sounds.
Someone has picked up another phone on
the same line. Hang up the other phone.
If you are using the headset, ensure the
headset plug is properly connected to the
jack.
Severe noise interference.
Press CH to change the channel.
Keep the handset away from computers,
remote control toys, wireless microphones,
alarm systems, intercoms, room monitors,
fluorescent lights, and electrical applianc-
es.
Move to another location or turn off the
source of interference.
Hang up and redial the number.
The phone cannot be operated at a
useful distance from the base
because the signal becomes weak
or noisy (handset’s range has
decreased).
Lift the base’s antenna to a fully vertical po-
sition.
Be sure neither the handset or base anten-
na is touching a metal surface.
Return the handset to the base to recharge
the battery pack.
The phone does not work or works
poorly.
Be sure the base’s phone line cord and
AC adapter are correctly and securely
connected, and the battery pack is
charged.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 21 Tuesday, August 17, 1999 3:37 PM
Problem
Suggestion
The handset battery pack does not
charge.
Check the charging contacts on the hand-
set and base. If they are dirty, clean them
with a pencil eraser.
Be sure the battery pack is properly con-
nected.
Be sure the handset is properly seated on
the base.
Handset does not ring or receive a
page when it is off the base.
Lift the base’s antenna to a fully vertical po-
sition.
Move the handset closer to the base.
Move the base away from other electrical
devices.
Return the handset to the base to recharge
the battery pack.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical po-
sition.
If the base lost power while the handset
was removed, the security access-protec-
tion code might have changed. With the
handset removed from the base, restore
power to the base, then place the handset
back on the base. The CHARGE indicator
lights, indicating that the code is set again.
Be sure the handset’s battery pack is
charged. (If the battery pack power is too
low, it does not have enough power to light
the TALK/BATT LOW indicator.)
If you still have problems, disconnect the phone. If other phones on the same line work
properly, the fault is in this phone or its installation. If you cannot find the problem, take
your phone to your local RadioShack store for assistance.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 22 Tuesday, August 17, 1999 3:37 PM
CARE AND MAINTENANCE
Your ET-925 900-MHz Dual Keypad Cordless Speakerphone is an example of supe-
rior design and craftsmanship. The following suggestions will help you care for your
cordless telephone so you can enjoy it for years.
Keep the ET-925 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Handle the ET-925 gently and carefully. Dropping it can damage circuit
boards and cases and can cause the ET-925 to work improperly.
Use and store the ET-925 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.
Keep the ET-925 away from dust and dirt, which can cause premature
wear of parts.
Wipe the ET-925 with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the ET-925.
Modifying or tampering with the ET-925’s internal components can cause a malfunc-
tion and might invalidate your ET-925’s warranty and void your FCC authorization to
operate it. If your ET-925 is not performing as it should, take it to your local Ra-
dioShack store for assistance. If the trouble is affecting the phone lines, the phone
company might ask you to disconnect your phone until you have resolved the prob-
lem.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 23 Tuesday, August 17, 1999 3:37 PM
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment and place the battery
pack into the compartment.
REPLACING THE
BATTERY PACK
If you follow the instructions in “Con-
necting and Charging the Battery
Pack” on Page 10, the battery pack
should last about one year. If the bat-
tery pack does not hold a charge for
more than 2 hours after an overnight
charge, replace the battery with a new
3.6-volt, 600 mAH battery with a con-
nector that fits the socket in the battery
compartment. You can order a re-
placement battery pack through your
local RadioShack store.
4. Replace the cover, then reinsert
and tighten the screw.
Cautions:
• You must use a replacement bat-
tery pack of the same size and
type.
• Do not dispose of the battery pack
in a fire because it might explode.
• Do not open or mutilate the battery
pack.
Install the new battery pack as de-
scribed below, then charge it for about
14 hours (see “Connecting and Charg-
ing the Battery Pack” on Page 10).
• Be careful not to short the battery
pack by touching the connector’s
pins with conducting materials,
such as rings, bracelets, and
keys. The battery pack or conduc-
tor might overheat and burn.
Note: To avoid losing phone numbers
stored in memory, try to install and be-
gin charging the new battery pack with-
in 3 minutes.
If you have trouble replacing the bat-
tery pack, take the phone to your local
RadioShack store for assistance.
1. Loosen the screw on the battery
compartment cover on the bottom
of the handset, and slide off the
cover in the direction of the arrow.
Important: This product contains a re-
chargeable nickel-cadmium battery
pack. At the end of the battery pack’s
useful life, it must be recycled or dis-
posed of properly. Contact your local,
county, or state hazardous waste man-
agement authorities for information on
recycling or disposal programs in your
area. Some options that might be
available are: municipal curb-side col-
lection, drop-off boxes at retailers such
as your local RadioShack store, recy-
cling collection centers, and mail-back
programs.
2. Lift the battery pack out of the
compartment, then gently pull on
the battery connector to discon-
nect it.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 24 Tuesday, August 17, 1999 3:37 PM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily dis-
continue your service. If this happens,
the phone company attempts to notify
you in advance. If advance notice is not
practical, the phone company notifies
you as soon as possible and advises
you of your right to file a complaint with
the FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To min-
imize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect
the operation of this telephone. The
telephone company notifies you of
these changes in advance, so you can
take the necessary steps to prevent in-
terruption of your telephone service.
Your telephone has built-in lightning
protection to reduce the risk of damage
from surges in telephone line and pow-
er line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electri-
cal circuit from the receiver
• Contacting your local RadioShack
store for help
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 25 Tuesday, August 17, 1999 3:37 PM
NOTES
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 26 Tuesday, August 17, 1999 3:37 PM
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 27 Tuesday, August 17, 1999 3:37 PM
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1095.fm Page 28 Tuesday, August 17, 1999 3:37 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UDZZ01841BZ
11A7
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|