43-1018.fm Page 1 Tuesday, August 17, 1999 8:53 AM
Cat. No. 43-1018
OWNER’S MANUAL
Please read before using this equipment.
ET-518
Cordless Telephone
with 9-Memory Speed-Dialing
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 3 Tuesday, August 17, 1999 8:53 AM
lar frequencies, within a certain area,
to inadvertently intercept your conver-
sations and/or cause interference on-
your cordless telephone. This lack of
privacy can occur with any cordless
telephone.
READ THIS BEFORE
INSTALLATION
We have designed your phone to con-
form to federal regulations, and you
can connect it to most phone lines.
However, each device that you con-
nect to the phone line draws power
from the line. We refer to this power
draw as the device’s ringer equiva-
lence number, or REN. The REN is
shown on the bottom of your phone.
However, your cordless phone is avail-
able in four different factory-set fre-
quencies. If you have problems with
interference, you can exchange your
phone within 30 days of purchase for
one that uses a different frequency.
If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phone might not ring. In rural ar-
eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.
Warning: To prevent fire or shock haz-
ard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
FCC STATEMENT
This telephone complies with Part 68
of FCC Rules. You must, upon re-
quest, provide the FCC Registration
Number and the REN to your phone
company. These numbers are located
on the bottom of your phone.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
Note: You must not connect your
phone to any of the following.
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
• Coin-operated systems
• Party-line systems
!
• Most electronic key phone sys-
tems
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 4 Tuesday, August 17, 1999 8:53 AM
TABLE OF CONTENTS
Installation ............................................................................................................ 5
Selecting a Mounting Location ........................................................................ 5
Placing the Base on a Desktop ................................................................. 5
Mounting the Base on a Wall Plate ........................................................... 6
Mounting the Base Directly on the Wall .................................................... 8
Preparation ......................................................................................................... 10
Installing the Handset Battery ........................................................................ 10
Charging the Handset Battery ........................................................................10
Setting the Dialing Mode ............................................................................... 11
Operation ............................................................................................................ 12
Making/Answering a Call ............................................................................... 12
Using the Handset at the Base ............................................................... 12
Using the Handset away from the Base .................................................. 12
Using Redial .................................................................................................. 13
Using Flash .................................................................................................... 13
Using Tone Services on a Pulse Line ............................................................ 13
Using Page .................................................................................................... 14
Memory Dialing .............................................................................................. 14
Storing a Number in Memory .................................................................. 14
Entering a Pause in a Memory Number .................................................. 15
Dialing a Stored Number ......................................................................... 16
Storing/Chain Dialing Special Service Numbers ..................................... 16
Testing Stored Emergency Numbers ...................................................... 16
Troubleshooting ................................................................................................. 17
Care And Maintenance ...................................................................................... 19
Replacing the Battery .....................................................................................20
The FCC Wants You to Know ........................................................................ 20
Lightning ........................................................................................................ 21
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 5 Tuesday, August 17, 1999 8:53 AM
INSTALLATION
self, using jacks and adapters avail-
able at your local Radio Shack store.
Or, you can let the phone company up-
date the wiring for you.
SELECTING A
MOUNTING LOCATION
You can mount the base on a wall
plate or directly on a wall. Or, you can
place it on a desk, shelf, or table. Se-
lect a location that is:
• The phone company will charge
you for the installation of the nec-
essary jacks.
• Near an AC outlet
• The USOC number of the jack to
be installed is RJ11C for a base-
board jack and RJ11W for a wall-
plate jack.
• Near a telephone line jack
• Out of the way of normal activities
• Away from computers, remote
control toys, wireless micro-
Placing the Base on a
Desktop
phones,
wireless
intercoms,
alarms and room monitors, fluo-
rescent lights, electrical machin-
ery, electrical appliances, metal
walls, filing cabinets, and other
large metal objects
Follow these steps to place the base
on a desk, shelf, or table.
For the best reception, you should be
able to fully extend the base’s antenna
and place it in a vertical position.
1. Plug one end of the supplied mod-
ular cord into the PHONE jack on
the back of the base.
2. Plug the modular cord’s other end
into a modular phone line jack.
The base’s location affects the phone’s
range. If you have a choice of several
locations, try each to see which one
provides the best performance.
3. Insert the supplied AC adapter’s
barrel plug into the 12V DC jack on
the back of the base.
If the phone line jack is not a modular
jack, you must update the wiring your-
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 6 Tuesday, August 17, 1999 8:53 AM
4. Plug the adapter into a standard
AC outlet.
2. Route the short cord downward
through the top left slot on the
base’s bottom and under the clips
as shown.
Caution: You must use a 120V AC/
12V DC adapter that delivers at least
200 milliamps. Its plug must correctly
12V DC
fit the phone’s
jack. The sup-
plied adapter meets these require-
ments. Using an adapter that does not
meet these requirements could dam-
age the phone or the adapter.
Mounting the Base on a Wall
Plate
3. Route the other end of the short
cord through the hole in the
bracket’s center.
You need a short modular cord (such
as Cat. No. 279-390, not supplied) and
a standard wall plate (Cat. No. 279-
382, not supplied), for this mounting
method.
4. To attach the supplied bracket to
the bottom of the base, insert the
tabs on the bracket into the slots
on the base, then slide the bracket
up.
1. Plug one end of the short modular
PHONE
cord into the
back of the base.
jack on the
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 7 Tuesday, August 17, 1999 8:53 AM
I
5. nsert the supplied AC adapter’s
barrel plug into the 12V DC jack on
the back of the base. Then route
the adapter’s cord through the
right slot on the base’s bottom and
under the clips as shown. Plug the
adapter into a standard AC outlet.
8. Press and lift out the handset
holder. Rotate the holder 180 as
°
shown, and then snap it back into
place so it holds the handset.
Note: If you later want to mount the
base on a desktop, press PUSH and
slide the bracket down to remove it
from the base’s bottom.
6. Plug the short modular cord into
the wall plate’s jack.
7. Align the bracket’s keyhole slots
with the wall plate studs and slide
the base downward to secure it.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 8 Tuesday, August 17, 1999 8:53 AM
3. On the bottom of the base, route
the modular cord downward and
under the left slot’s clips as
shown.
Mounting the Base Directly
on the Wall
You need two wood screws (not sup-
plied) for this mounting method.
15
1. Drill two holes 3 /16 inches apart.
Then thread a screw into each
1
hole, letting the heads extend /4
inch from the wall.
4. To attach the supplied bracket to
the bottom of the base, insert the
tabs on the bracket into the slots
on the base, then slide the bracket
up.
2. Plug one end of the supplied mod-
ular cord into the PHONE jack on
the back of the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 9 Tuesday, August 17, 1999 8:53 AM
5. Insert the supplied AC adapter’s
barrel plug into the 12V DC jack on
the back of the base. Then route
the adapter’s cord through the
right slot on the base’s bottom and
under the clips. Plug the adapter
into a standard AC outlet.
8. Press and lift out the handset
holder. Rotate the holder 180 as
°
shown, and then snap it back into
place so it holds the handset.
If you later want to mount the
Note:
base on a desktop, press PUSH and
slide the bracket down to remove it
from the base’s bottom.
6. Plug the modular cord into a mod-
ular phone line jack.
7. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 10 Tuesday, August 17, 1999 8:53 AM
PREPARATION
INSTALLING THE
CHARGING THE
HANDSET BATTERY
HANDSET BATTERY
Your phone comes with a battery
which you must install, connect, and
charge for 15 hours before you use
your phone for the first time.
When you install a new battery, set
POWER to OFF. Then place the hand-
set on the cradle so the IN USE/
CHARGE indicator lights and charge
the battery for about 15 hours.
To install the battery:
Recharge the battery when LOW
BATT on the handset lights.
1. Slide off the battery compartment
cover.
Caution: To avoid damage to the bat-
tery, always recharge the handset bat-
tery as soon as LOW BATT lights.
2. Insert the battery into the compart-
ment so its connector can reach
the pins inside the compartment,
and secure it with the plastic
strap.
Notes:
• You can set POWER to ON while
the battery charges, but it charges
more quickly if you set POWER to
OFF.
3. Slide the battery’s connector onto
the pins.
Caution: The connector only fits
one way; do not force it. If you
have difficulty sliding the connec-
tor onto the pins, turn it over and
try again.
• If the IN USE/CHARGE indicator
does not light when you place the
handset on the cradle, be sure the
battery is connected to the pins
inside the battery compartment,
and the AC adapter is securely
connected to the base. Also,
check the charging contacts on
4. Replace the cover, then follow the
instructions under “Charging the
Handset Battery’’ before you use
the phone.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 11 Tuesday, August 17, 1999 8:53 AM
the handset and base. If the con-
nects are dirty or tarnished, gently
clean them with a pencil eraser.
SETTING THE DIALING
MODE
Set TONE/PULSE on the back of the
base for the type of service you have.
If you are not sure which type you
have, do this test.
1. Set TONE/PULSE to TONE.
• About once a month, fully dis-
charge the battery by keeping the
handset off the cradle until LOW
BATT lights, then return the hand-
set to the cradle and fully
recharge the battery. If you do not
fully discharge and recharge the
battery periodically, it loses its
ability to fully recharge.
2. Lift the handset and listen for a
dial tone.
3. Press any number other than 0.
• The first time you use your phone
after installing a new battery, the
handset might not work and might
sound an error tone when you
press TALK. This might also occur
when you recharge a battery that
has been completely discharged.
If this happens, be sure the hand-
set is turned on. Then return the
handset to the cradle for 5 sec-
onds. This resets the security
access code.
If the dial tone stops, you have
touch-tone service. Leave TONE/
PULSE set to TONE.
If the dial tone continues, you
have pulse service. Set TONE/
PULSE to PULSE.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 12 Tuesday, August 17, 1999 8:53 AM
OPERATION
Using the Handset Away from
the Base
MAKING/ANSWERING A
CALL
To use the handset away from the
base, set POWER to ON, then press
TALK to make or answer a call. The
TALK indicator lights.
You can use your cordless telephone
in two ways: at the base or away from
the base.
Using the Handset at the
Base
You can use the handset at the base
like a regular corded telephone. Just
set the handset’s POWER to ON and
place the handset in the cradle.
To disconnect a call, press TALK so
the TALK indicator turns off.
Notes:
• To conserve battery power, you
can turn off the handset’s power
when you are not making or
answering a call. The cordless
phone does not ring when it
receives an incoming call with the
handset’s power turned off. How-
ever, other phones on the same
line still ring. Set POWER to ON to
answer the call using the cordless
phone.
To answer a call, just lift the handset
from the base.
To make a call, lift the handset from
the base and press TALK so the TALK
indicator lights.
• You can make or answer a call on
a phone on the same line as the
cordless phone, even if the hand-
set is away from the base.
To disconnect a call, replace the hand-
set on the base.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 13 Tuesday, August 17, 1999 8:53 AM
• When dialing a number, if you
press a number and 3 short beeps
sound, you are out of the base’s
range, the battery is too low, or
there is too much interference on
the line. Move the handset closer
to the base or recharge the bat-
tery, if necessary.
USING FLASH
FLASH
Use
on the handset to send the
electronic equivalent of a switchhook
press for special services, such as call
waiting.
USING REDIAL
To quickly redial the last number di-
aled, simply lift the handset from the
TALK
base or press
so the TALK indi-
REDIAL
For example, if you have call waiting,
cator lights. Then press
.
FLASH
press
to take an incoming call
without disconnecting the current call.
FLASH
Press
call.
again to return to the first
Notes:
• If you do not have any special
FLASH
phone services, pressing
might disconnect the current call.
The redial memory holds up to 80 dig-
its, so you can redial long distance as
well as local numbers.
• The redial memory does not store
FLASH
a
entry or any digits
FLASH
entered after you press
.
Notes:
• We recommend you not use
USING TONE SERVICES
ON A PULSE LINE
REDIAL
to dial numbers that
TONE
include a
entry (see “Using
Tone Services on a Pulse Line”).
Some special services, such as bank
by phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow-
ing these steps.
• The redial memory does not store
FLASH
a
entry or any digits
FLASH
entered after you press
.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 14 Tuesday, August 17, 1999 8:53 AM
1. Be sure TONE/PULSE on the base
MEMORY DIALING
is set to PULSE.
You can store nine telephone numbers
in memory and then dial them by
pressing the corresponding memory
location number. Each stored number
can be up to 16 digits long.
2. Dial the service’s main number.
3. When the service answers, press
TONE. Then dial the additional
numbers. The phone sends these
numbers as tone signals.
Notes:
• When using special tone service
numbers, we recommend that you
manually press TONE, rather than
storing the entry in memory. How-
ever, you can store the service’s
main number in one location and
numbers for additional information
in other locations. See “Storing/
Chain Dialing Special Service
Numbers.”
4. When you complete the call, place
the handset on the cradle or press
TALK to disconnect the call. The
phone automatically resets to the
pulse mode.
• To keep your accounts secure, we
recommend you NOT store your
personal access code for services
such as bank-by-phone in a mem-
ory location.
We recommend you not use RE-
DIAL to dial numbers that include a
TONE entry.
Note:
USING PAGE
Storing a Number in Memory
PAGE allows someone at the base to
page you at the handset or helps you
find the handset if you misplace it. With
the handset’s POWER set to ON and its
TALK indicator off, the handset sounds
four sets of four beeps when someone
presses PAGE on the base.
1. Make sure the handset’s POWER
is set to ON and TALK is not lit.
2. Press MEMO.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 15 Tuesday, August 17, 1999 8:53 AM
Note: While you are storing a
number in memory, if you do not
press any button on the keypad
within about 10 seconds, the
handset beeps three times and
Notes:
• If you receive a call while you are
storing a number in memory,
TALK
press
to answer the call.
After the call, begin again at Step
1 to store the number.
MEMO
you must press
again to
store the telephone number.
• To change the phone numbers
stored in memory, repeat Steps 1-
6. The new phone number
replaces the previously stored
phone number in that memory
location.
3. Dial the number.
MEMO
4. Press
again.
1 9
5. Press the number ( - ) for the
memory location where you want
to store the number. The phone
beeps twice. The phone number is
now stored in memory.
• To clear a memory location so no
number is stored there, press
MEMO PAUSE MEMO
, and then
,
,
TALK
6. Press
mode.
twice to exit the store
the location number. The phone
beeps twice and the phone num-
ber is now cleared from the mem-
ory.
7. Repeat Steps 2-6 for other tele-
phone numbers.
8. Remove the plastic covering from
the base’s index sheet with a
small pointed object, such as the
end of a straightened paper clip.
Write the person’s or company’s
name and memory location num-
ber on the sheet in pencil (in case
you want to store a different num-
ber later).
• If AC power fails, the phone beeps
three times and keeps stored
numbers in memory.
Entering a Pause in a Memory
Number
In some telephone systems, you must
9
dial an access code ( , for example)
and wait for a second dial tone before
you can dial an outside number. If your
phone is connected to one of these
systems, you might want to enter a
pause at the appropriate point when
you store a phone number in memory.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 16 Tuesday, August 17, 1999 8:53 AM
At the appropriate place in the number,
press REDIAL to enter a 2-second
pause. For a longer pause, press RE-
DIAL again (each press enters a 2-sec-
ond pause).
If you use pulse dialing to
Note:
dial the service, after the service
answers, press TONE before pro-
ceeding with the next step.
3. Press MEMO and the memory-
location numbers for the addi-
tional information.
Dialing a Stored Number
4. To disconnect the call, press TALK
Follow these steps to dial a number
stored in memory.
so the TALK indicator turns off.
1. Lift the handset from the cradle or
press TALK so the TALK indicator
lights.
Testing Stored Emergency
Numbers
2. When you hear a dial tone, press
MEMO, then press the correct
memory location button. The
phone dials the stored number.
If you store an emergency service’s
number (police department, fire de-
partment, ambulance) and you choose
to test the stored number, remain on
the line to explain the reason for your
call. Make the test call during the late
evening or early morning hours to
avoid peak demand periods.
Storing/Chain Dialing Special
Service Numbers
When storing numbers for special ser-
vices (such as alternate long distance
or bank by phone services), store the
service’s main phone number in one
memory location and numbers for ad-
ditional information in other locations.
Follow these steps to chain-dial mem-
ory numbers.
1. With the handset’s POWER set to
ON and TALK lit, press MEMO and
the memory-location number for
the service’s main number.
2. Wait for the service to answer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 17 Tuesday, August 17, 1999 8:53 AM
TROUBLESHOOTING
We do not expect you to have any problems with your telephone, but if you do, the
following suggestions might help. If you still have problems, check other phones on
the same line to see if they work properly. If they do and the problem does not seem
to be with your phone service, take your phone to your local Radio Shack store for
assistance.
Problem
Solution
• Be sure POWER is ON.
The handset does not
work.
• Move the handset closer to the base.
• Be sure the phone line cord and AC adapter are
correctly and securely connected.
• Be sure the battery is charged.
• Fully extend the base’s antenna vertically.
• Return the handset to the cradle for 5 seconds,
then try again.
• Your phone has a special circuit that protects it
from static discharge. The circuit turns off the
handset if it receives a static discharge. Turn the
handset off for a few seconds to reset this circuit.
Volume drops or you
hear unusual sounds.
• Someone has picked up another phone on the
same line. Hang up the other phone.
Call is noisy.
• Do not mount the base near electrical appliances
or large metal objects.
• Hang up and redial the number.
• Keep the handset away from interference
sources such as computers, remote control toys,
wireless microphones, wireless alarm systems,
wireless intercoms and room monitors, and fluo-
rescent lights. If the interference is severe, turn
off the interfering device.
• Exchange your phone for one with a different
operating frequency (within 30 days of the date
of purchase).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 18 Tuesday, August 17, 1999 8:53 AM
Problem
Solution
The handset’s range
decreases.
• Fully extend the base’s antenna in a vertical posi-
tion
• Return the handset to the cradle, and recharge
the battery
• Be sure the antenna is not touching a metal sur-
face.
Receiver sound flutters
or fades.
• Be sure the battery is charged.
Can make calls, but
telephone does not
ring.
• Handset’s POWER must be set to ON to ring.
Can receive calls, but
cannot make calls.
• Set TONE/PULSE on the base correctly for your
type of service.
You cannot answer/
make a call and the
handset sounds an
error tone when you lift
it from the base or
press TALK.
• The phone might be receiving interference from
another RF signal; or, if the handset is away from
the base during a long period of AC power failure,
the phone might lose its access protection code.
Return the handset to the base for a few sec-
onds.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 19 Tuesday, August 17, 1999 8:53 AM
CARE AND MAINTENANCE
Your ET-518 Cordless Telephone with 9-Memory Speed-Dialing is an example of
superior design and craftsmanship. The following suggestions will help you care for
your phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Handle the phone gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the phone to work improperly.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature
wear of parts.
Wipe the phone with a damp cloth occasionally to keep it looking
CLEANER
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate your phone’s warranty. If your phone is not performing as
it should, take it to your local Radio Shack store for assistance.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 20 Tuesday, August 17, 1999 8:53 AM
4. Replace the battery compartment
cover.
REPLACING THE
BATTERY
Important: Your telephone contains a
rechargeable nickel cadmium battery.
At the end of the battery’s useful life, it
must be recycled or disposed of prop-
erly. Contact your local, county, or
state hazardous waste management
authorities for information on recycling
or disposal programs in your area.
Some options that might be available
are: municipal curb-side collection,
drop off boxes at retailers, recycling
collection centers, and mail back pro-
grams.
If you follow the instructions in “Charg-
ing the Battery,’’ the supplied battery
should last for over 1 year. When the
battery loses its ability to fully charge,
order a 3.6 volt, 300 milliamp battery
with a connector that fits the connector
in the battery compartment. You can
order a replacement battery through
your local Radio Shack store.
Install the new battery as described
below, then charge the battery (see
“Charging the Battery’’).
1. Slide off the battery compartment
cover and loosen the plastic strap
securing the battery. Then discon-
nect and remove the old battery.
THE FCC WANTS YOU
TO KNOW
2. Insert the new battery in the com-
partment and secure it with the
plastic strap.
In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this hap-
pens, the phone company attempts to
notify you in advance. If advance no-
tice is not practical, the phone compa-
ny notifies you as soon as possible and
advises you of your right to file a com-
plaint with the FCC.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect
the operation of the phone. The phone
company notifies you of these changes
in advance, so that you can take the
necessary steps to prevent interrup-
tion of your phone service.
3. Slide the battery’s connector onto
the pins inside the compartment.
Caution: The connector only fits
one way; do not force it. If you
have difficulty sliding the connec-
tor onto the pins, turn it over and
try again.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 21 Tuesday, August 17, 1999 8:53 AM
Your phone might cause TV or radio
interference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing the inter-
ference. Try to eliminate interference
by:
LIGHTNING
Your phone has built-in protection cir-
cuits to reduce the risk of damage from
surges in phone line current. These
protection circuits meet or exceed the
FCC requirements. However, lightning
striking the phone lines can damage
your phone.
• Moving your phone away from the
receiver
Lightning damage is not common.
Nevertheless, if you live in an area that
has severe electrical storms, we sug-
gest that you unplug your phone during
storms to reduce the possibility of
damage.
• Connecting your phone to an AC
outlet that is on a different electri-
cal circuit from the receiver
• Contacting your local Radio
Shack store for help
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your phone.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 22 Tuesday, August 17, 1999 8:53 AM
NOTES
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 23 Tuesday, August 17, 1999 8:53 AM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1018.fm Page 24 Tuesday, August 17, 1999 8:53 AM
RADIO SHACK LIMITED WARRANTY
This telephone product is warranted against manufacturing defects in material and
workmanship for one (1) year from the date of purchase from Radio Shack company
owned stores and authorized Radio Shack franchisees and dealers. Within this period
bring your Radio Shack sales slip as proof-of-purchase date to any Radio Shack
store.
This warranty does not cover damage or failure caused by or attributable to Acts of
God, abuse, misuse, improper or abnormal usage, faulty installation, improper mainte-
nance, lightning or other incidence of excess voltage, or any repairs other than those
provided by a Radio Shack Authorized Service Facility, or transportation costs. Radio
Shack is not responsible or liable for indirect, special, or consequential damages
arising out of or in connection with the use or performance of the product or
other damages with respect to loss of property, loss of revenue or profit, or costs
of removal, installation or reinstallation.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRAN-
TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states
do not allow the limitation or exclusion of incidental or consequential damages and
some states do not allow limitation or exclusion of implied warranties; therefore, the
aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. There will be
charges rendered for repairs to the product made after the expiration of the aforesaid
one (1) year warranty period.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
We Service What We Sell
9/94
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
7A5
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|