43-1102.fm Page 1 Tuesday, August 17, 1999 4:37 PM
Cat. No. 43-1102
OWNER’S MANUAL
Please read before using this equipment.
ET-1102
900 MHz Digital Spread Spectrum
Cordless Telephone
with Caller ID/Call Waiting ID
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 3 Tuesday, August 17, 1999 4:37 PM
Flash — sends an electronic switch-
hook signal for use with special phone
services, such as Call Waiting.
Important Caller ID Information
To use the phone’s Caller ID and Caller
ID with Call Waiting features, you must
be in an area where those services are
available and you must subscribe to
those services through your local phone
company.
Tone/Pulse Dialing — lets you use ei-
ther type of service, and you can easily
switch from pulse to tone dialing for
long-distance, bank-by-phone, or other
special services.
Where Caller ID is offered, one or more
options are generally available:
Auto Talk — you can set the phone so
you can answer a call simply by lifting
the handset from the base.
• caller’s number only
• caller’s name only
Any Key Answer — you can set the
phone so you can press any key to an-
swer a call when the handset is away
from the base.
• caller’s name and number
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
Hearing-Aid Compatibility — lets you
use your phone with hearing aids that
have a T (telephone) switch.
CAUTION
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
Serial Number __________________
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 4 Tuesday, August 17, 1999 4:37 PM
Important:
FCC STATEMENT
• Cordless phones such as this one
require AC power to operate. When
the AC power is off, you cannot dial
out or receive incoming calls using
your ET-1102. To be safe, you
should also have a phone that does
not need AC power to operate (not a
cordless phone) so you can still
make and receive calls if there is an
AC power failure.
Your telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your phone company.
These numbers are on the bottom of the
base.
You must not connect your phone to any
of the following:
• coin-operated systems
• When AC power is lost, the ET-1102
loses the security access-protection
code connection between the base
and the handset. When power is re-
stored, put the handset on the base
briefly to restore this connection so
you can use the handset.
• party-line systems
• most electronic key phone systems
This equipment complies with the limits
for a Class B digital device as specified
in Part 15 of FCC Rules. These limits
provide reasonable protection against
radio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly. To elimi-
nate interference, you can try one or
more of the following corrective mea-
sures.
READ THIS BEFORE
INSTALLATION
We have designed your phone to con-
form to federal regulations and you can
connect it to most phone lines. However,
each device that you connect to the tele-
phone line draws power from the line.
We refer to this power draw as the
phone’s ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical cir-
cuits for the equipment and the ra-
dio or TV.
If you use more than one phone or other
device on the line, add up all the RENs.
If the total is more than five, your phones
might not ring. In rural areas, a total
REN of three might impair ringer opera-
tion. If ringer operation is impaired, re-
move one of the devices from the line.
Consult your local Radio Shack store if
the problem still exists.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 5 Tuesday, August 17, 1999 4:37 PM
CONTENTS
Installation ............................................................................................................... 6
Mounting the Phone ........................................................................................... 6
On a Desk .................................................................................................... 6
On a Wall Plate ............................................................................................ 7
Directly on the Wall ...................................................................................... 8
Connecting and Charging the Battery Pack ....................................................... 9
Setting the Dialing Mode .................................................................................. 11
Setting the Ringer’s Volume ............................................................................. 12
Using Auto Talk ................................................................................................ 12
Turning Caller ID/Call Waiting On/Off ............................................................... 12
Storing Your Area Code ................................................................................... 13
Telephone Operation ............................................................................................ 14
Making and Receiving Calls ............................................................................. 14
Adjusting the Handset Volume ......................................................................... 14
Using REDIAL .................................................................................................. 14
Using FLASH .................................................................................................... 15
Using Tone Services on a Pulse Line ............................................................... 15
Paging .............................................................................................................. 15
Memory Dialing ................................................................................................ 16
Storing a Name and Number in Memory ................................................... 16
Editing or Deleting a Number in Memory ................................................... 17
Entering a Pause ....................................................................................... 18
Reviewing Memory Numbers ..................................................................... 18
Dialing a Memory Number ......................................................................... 18
Chain-Dialing Service Numbers ................................................................. 19
Testing Stored Emergency Numbers ......................................................... 19
Using a Headset ............................................................................................... 19
Caller ID Operation ............................................................................................... 20
Reviewing Caller ID Records ........................................................................... 20
Caller ID Messages ................................................................................... 21
Dialing Numbers from a Caller ID Record ........................................................ 21
Storing a Caller ID Record to Memory ............................................................. 21
Deleting Caller ID Records ............................................................................... 22
Troubleshooting .................................................................................................... 23
Care and Maintenance .......................................................................................... 25
Replacing the Battery Pack .............................................................................. 26
The FCC Wants You to Know ........................................................................... 27
Lightning ........................................................................................................... 27
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 6 Tuesday, August 17, 1999 4:37 PM
INSTALLATION
On a Desk
MOUNTING THE PHONE
Follow these steps when you place the
base on a desk or table.
You can place the ET-1102’s base on a
desk or table, mount it on a standard
wall plate, or mount it directly on a wall.
Choose a location that is:
1. Insert the bracket’s tabs into the
base’s upper tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
• near an AC outlet
• near a telephone line jack
• out of the way of normal activities
Clip Slots
Clips
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
Upper Tab Slots
The base’s location affects the hand-
set’s range. If you have a choice of sev-
eral locations, try each to see which
provides the best performance.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
Caution: The supplied RadioShack
adapter was designed specifically for
your ET-1102. Use only the supplied
adapter.
Notes:
• Your telephone connects directly to
a modular phone line jack. If your
phone line jack is not a modular
jack, you can update the wiring
yourself, using jacks and adapters
available from your local Ra-
dioShack store. Or, you can let the
telephone company update the wir-
ing for you.
3. Plug the modular cord’s other end
into a modular phone line jack.
• The USOC number of the jack to be
installed is RJ11C, or RJ11W for a
wall plate jack.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 7 Tuesday, August 17, 1999 4:37 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
Lower
Tab
Slots
Tabs
Clip Slots
5. Route the adapter’s cord through
the strain relief slot on the bracket.
2. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base.
Strain
Relief Slot
6. Plug the adapter into a standard AC
outlet.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
7. Lift the base’s antenna to a vertical
position.
4. Route the adapter’s cord through
the narrow groove on the bottom of
the bracket.
On a Wall Plate
1. Insert the bracket’s tabs into the
base’s lower tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
Narrow
Groove
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 8 Tuesday, August 17, 1999 4:37 PM
5. Plug the modular cord into the wall
plate jack, then align the bracket’s
keyhole slots with the wall plate
studs and slide the base downward
to secure it.
Directly on the Wall
For this mounting method, you need two
screws (not supplied) with heads that fit
into the keyhole slots on the bottom of
the base.
5/16"
1. Drill two holes 315/16
inches (100 mm)
apart. Then thread a
15/16"
screw into each hole,
letting the heads ex-
tend about /16 inch (8
3
5
mm) from the wall.
6. Plug the adapter into a standard AC
outlet.
2. Insert the bracket’s tabs into the
base’s lower tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
Lower
Tab
Slots
7. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place.
Tabs
Clip Slots
3. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
8. Lift the base’s antenna to a vertical
position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 9 Tuesday, August 17, 1999 4:37 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
8. Plug the adapter into a standard AC
outlet.
5. Route the modular and adapter
cords through the grooves on the
bottom of the bracket.
9. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place so it holds the handset.
Grooves
6. Align the keyhole slots with the
mounting screws, and slide the base
downward to secure it.
10. Lift the base’s antenna to a vertical
position.
CONNECTING AND
CHARGING THE BATTERY
PACK
The ET-1102 comes with a recharge-
able nickel-cadmium battery pack in the
handset but not connected. Before using
your phone, you must connect the bat-
tery pack, then charge it for about 24
hours.
7. Plug the modular cord into a modu-
lar phone line jack.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 10 Tuesday, August 17, 1999 4:37 PM
1. Press down and slide off the battery
pack compartment cover as shown.
Important: Be sure the battery pack is
properly connected before you try to
charge it. The CHARGE indicator lights
when the handset is on the base, even if
the battery pack is not connected.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone when
you press TALK. If this happens, re-
turn the handset to the base for
about 5 seconds. This resets the se-
curity access-protection code.
2. Unfasten the plastic retainer strap
and lift the battery pack out of the
compartment.
• If the base loses power for 30 min-
utes while the handset is away from
it, the security access-protection
code might be lost. To reset the
code, return the handset to the base
for about 5 seconds.
3. Plug the battery pack’s connector in-
to the socket in the compartment
(the connector fits only one way),
then replace the battery pack and
fasten the retainer strap.
The handset does not lose its secu-
rity access-protection code even if
the battery pack is completely dis-
charged.
4. Replace the cover.
To charge the battery pack, place the
handset either faceup or facedown on
the base. The CHARGE indicator on the
base lights and Total:00appears on
the handset display.
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month.
CHARGE Indicator
Recharge the battery pack when Low
Batteryflashes on the display.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 11 Tuesday, August 17, 1999 4:37 PM
• If the battery pack becomes weak
during a call, the handset beeps ev-
ery 3 seconds and Low Battery
flashes. When this happens, you
cannot make another call on the
phone until you recharge the battery
pack.
SETTING THE DIALING
MODE
DIAL MODE
Set
on the back of the base
for the type of service you have. If you
are not sure which type you have, once
the battery pack is fully charged, do this
test.
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until Low
Battery flashes. Otherwise, the
battery pack loses its ability to fully
recharge.
DIAL MODE
T
1. Be sure
(tone).
is set to
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be
too low to light the display.)
TALK
2. Lift the handset, press
listen for a dial tone.
, and
• If you are not going to use your
phone for an extended period of
time, disconnect the battery pack.
This increases the battery pack’s
usable life.
• The supplied battery pack should
last for about a year. When it loses
its ability to fully recharge, order a
replacement battery pack from your
local RadioShack store (see “Re-
placing the Battery Pack” on
Page 26).
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not dial the access code
either.
If the dial tone stops, you have
DIAL
touch-tone service. Leave
MODE
T
set to .
If the dial tone continues, you have
DIAL MODE
P
pulse service. Set
(pulse).
to
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 12 Tuesday, August 17, 1999 4:37 PM
SELECT
2. Press
to change the auto
SETTING THE RINGER’S
VOLUME
talk setting. Onor Offappears indi-
cating the selected setting.
At any time except during a call, press
VOL
s or t to set the ringer volume. The
phone rings at the selected volume and
the display shows Ringer High or
RingerLow.
3. To clear the display when you finish,
FUNCTION
press
set to the base.
or return the hand-
TURNING CALLER ID/
CALL WAITING ON/OFF
USING AUTO TALK
If you have Call Waiting with Caller ID
service, you can set the ET-1102 to
show Caller ID information for an incom-
ing call even while you are already on
the phone.
Your phone is preset so you must press
TALK
to answer a call. With auto talk
turned on, you can answer a call by just
lifting the handset from the base, or, if
the handset is away from the base, by
pressing any key.
Follow these steps to turn the Caller ID/
Call Waiting feature on or off.
Follow these steps to turn auto talk on or
off.
FUNC-
1. Lift the handset and press
TION
.
FUNC-
1. Lift the handset and press
TION
Talkselected.
. A menu appears with Auto
2
2. Press or t to select CIDCW(Caller
ID/Call Waiting).
SELECT
3. Press
to change the Caller
ID/Call Waiting setting. On or Off
appears indicating the selected set-
ting.
4. Return the handset to the base to
store the new setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 13 Tuesday, August 17, 1999 4:37 PM
SELECT
3. Press
to store the area
FUNCTION
STORING YOUR AREA
CODE
code, then press
turn the handset to the base to clear
the display.
or re-
To quickly dial a number from a Caller
ID record (see “Dialing Numbers from a
Caller ID Record” on Page 21) or to cor-
rectly store a number from a record into
a memory dialing location (see “Storing
a Caller ID Record to Memory” on
Page 21), you must store your local area
code in the ET-1102’s memory. Then,
when you dial from a Caller ID record,
the ET-1102 skips the area code if it
matches the one you stored.
Follow these steps to store your area
code.
FUNC-
1. Lift the handset and press
TION
.
3
1. Press (or t twice) to select Area
Code.
SELECT
, then enter your 3-
2. Press
digit area code. If you make a mis-
take, repeatedly press or to
move the cursor over the incorrect
digit, then enter the correct number.
Note: If an area code is already
stored, it appears on the display
SELECT
. To delete
when you press
the area code, press
times. Then enter your area code.
DELETE
three
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 14 Tuesday, August 17, 1999 4:37 PM
TELEPHONE OPERATION
MAKING AND RECEIVING
CALLS
ADJUSTING THE
HANDSET VOLUME
To make a call, lift the handset and
press TALK (the IN USE indicator on the
base lights), then dial the number. You
see the number as you dial, then (after a
few seconds) the call’s elapsed time.
To adjust the volume of the sound you
hear through the handset, during a call,
press VOL t for normal volume or VOL s
for high volume. The display shows
VolumeNormalor VolumeHigh.
Note: You can also dial the number be-
fore you press TALK. If you make a mis-
USING REDIAL
take, repeatedly press
or
until the
cursor is over the incorrect digit, then
enter the correct number.
You can quickly dial the last number di-
aled. Lift the handset and press TALK,
then press REDIAL.
To answer a call, lift the handset from
the base and press TALK. If auto talk is
on, just lift the handset from the base,
or, if the handset is away from the base,
press any key.
To end a call, place the handset on the
base or press TALK.
Notes:
• You can also press REDIAL (so you
see the stored number) first, then
press TALK.
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 18.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 15 Tuesday, August 17, 1999 4:37 PM
3. When the service answers, press
TONE
USING FLASH
(
). Any additional numbers
you dial are sent as tone signals.
FLASH
performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
4. To reset the phone to pulse dialing,
FLASH
simply hang up or press
“Using FLASH” on Page 15).
(see
For example, if you have Call Waiting,
FLASH
press
to answer an incoming call
without disconnecting the current call.
FLASH
Press
call.
again to return to the first
PAGING
Note: If you do not have any special
To page the person who has the hand-
set or to locate the handset when the
FLASH
phone services, pressing
disconnect the current call.
might
PAGE/FIND
phone is not in use, press
The handset beeps for 2 seconds.
.
To have the handset beep for a full
PAGE/FIND
USING TONE SERVICES
ON A PULSE LINE
minute, hold down
onds. To stop the beeping sooner, press
TALK
for 2 sec-
twice.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse dialing, you can still use
these special tone services by following
these steps.
DIAL MODE
P
1. Be sure
is set to .
2. Dial the service’s main number.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 16 Tuesday, August 17, 1999 4:37 PM
SELECT
4. To store a name, press
.
MEMORY DIALING
StoreNameappears.
You can store up to ten phone numbers
and names in memory, then dial a stored
number by entering its memory location
number.
Each stored number can be up to 20
digits, and each name can be up to 14
characters.
If you do not want to enter a name,
skip to Step 6. <Memoryn> will be
stored as the name (nis the location
number you selected).
Storing a Name and Number in
Memory
5. To enter a name, use t or s to select
the characters and
the cursor.
or
to move
Notes:
• An error tone sounds and the phone
exits the storing process if you wait
more than 20 seconds between
each key press.
• If you receive a call during memory
entry, the phone exits the storing
process.
Repeatedly press t to see the char-
acters in alphabetical order. (The
display shows uppercase letters
first, then lowercase letters, num-
bers, and special characters.)
1. Lift the handset.
MEM
2. Hold down
until Memory
Store and a list of memory loca-
tion numbers appears.
Notes:
• Press s to see the characters in
reverse alphabetical order.
• You can hold down s or t to scroll
rapidly through the characters.
3. Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing s or t.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 17 Tuesday, August 17, 1999 4:37 PM
• If you make a mistake, move the
cursor over the error, then enter
the correct character, or press
DELETE to delete a character. To
delete all the characters, hold
down DELETE for at least 1 sec-
ond.
For each stored number, write the per-
son’s or company’s name next to the ap-
propriate location number on the
supplied memory directory sticker. (Use
a pencil in case you need to change the
number later.) Peel the backing from the
sticker and attach it to the phone as
shown.
6. Press SELECT. StoreNumberap-
pears.
7. Enter the phone number and any
tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 15 and “Entering a Pause” on
Page 18).
To replace a stored number, simply store
a new one in its place.
Editing or Deleting a Number in
Memory
Instead of using the lower keypad
keys, you can use t or s to enter the
number and other entries and
or
Follow these steps to edit or delete a
memory number.
to move the cursor. Repeatedly
press t to see the numbers first, then
special characters, including hy-
phens, pause entries (P), and tone
entries ( ). Press s to see them in
reverse order.
1. Lift the handset.
2. Hold down MEM until Memory
Store and a list of memory loca-
tion numbers appear on the display.
8. Press SELECT. The phone beeps
and Memory n Stored appears.
After 2 seconds, Memory Store
appears, and you can repeat Steps
3–8 to store more numbers.
3. Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing s or t.
9. When you finish, press MEM to exit
the MemoryStoredisplay.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 18 Tuesday, August 17, 1999 4:37 PM
4. Press SELECT. A menu appears
with the three options listed below.
Press s or t to choose an option, fol-
low the instructions listed, then
press SELECT.
Reviewing Memory Numbers
To review your memory numbers, press
MEM. The list of memory location num-
bers (0–9) appears with the name stored
with each number (or <Memory n>if
you did not store a name).
EditMemoryn. Edit the record as
described in Steps 5 through 8 of
“Storing a Name and Number in
Memory” on Page 16.
To see the stored phone numbers, press
. An arrow to the right of the number
means it is longer than 14 digits. Press
again to see the rest of the number.
Delete Memory n. The display
prompts you to confirm the deletion.
Move the cursor to Yesor No, then
press SELECT or DELETE. The
phone beeps, and Memory n De-
letedappears.
Repeatedly press
name display.
to return to the
To exit the memory number list, press
MEM.
GoBack. Returns you to the list of
memory numbers.
To see a stored name and phone num-
ber at the same time, press SELECT
when the cursor is by a memory location
number. To exit this display without stor-
ing any changes, hold down DELETE un-
til the display clears.
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. To en-
ter a 2-second pause, press PAUSE or
use s or t to select Pon the display. You
can add more pause entries for a longer
pause.
Dialing a Memory Number
To dial a number stored in memory, lift
the handset and press MEM. The list of
memory location numbers appears.
Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing s or t, then press TALK.
You can also dial a memory number by
pressing TALK first, then pressing MEM
and entering a memory location number.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 19 Tuesday, August 17, 1999 4:37 PM
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as bank by phone), store
each group of numbers in its own mem-
ory location.
Dial the service’s main number first.
Then, at the appropriate place in the
call, press MEM and enter the number
for the location where the additional in-
formation is stored.
Notes:
• Connecting a headset disconnects
Testing Stored Emergency
Numbers
the handset’s earpiece and micro-
phone.
• VOL s or t on the handset also con-
trols the headset’s volume.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
• If you place the handset on the base
to recharge it while the headset is
connected, be sure the handset
seats properly.
With a headset connected, you can
make or answer calls as usual using the
keys on the handset.
USING A HEADSET
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for greater
convenience.
You can make or answer calls with
hands-free convenience using an op-
3
tional headset that has a /32-inch (2.5-
mm) plug. Contact your local Ra-
dioShack store for a suitable headset.
When you finish using the headset, dis-
connect it from the handset and close
the rubber cover to protect the jack.
To connect the headset, pull open the
rubber cover marked
on the side of
the handset, then insert the headset’s
plug into the jack.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 20 Tuesday, August 17, 1999 4:37 PM
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone compa-
ny sends information about the call, as
well as the time and date, between the
first and second rings of every call you
receive.
Note: If the handset is faceup on the
base, it shows the number of Caller ID
records, so you can see if you have new
records to review.
Repeatedly press t to scroll through the
Caller ID records from the newest to the
oldest, or s to scroll back through the
records. To scroll quickly through the
records, hold down t or s.
The ET-1102 displays this information
when it receives a call, and it stores up
to 50 Caller ID records for later review. It
also shows if caller information is un-
available or if the name and number
When you scroll past the last record,
were blocked by the caller (see “Caller Endappears. When you scroll past the
ID Messages” on Page 21).
first record, the record totals appear.
If you subscribe to Call Waiting with Call-
er ID, you will hear a tone through the
handset when a call comes in, then the
Caller ID record appears. If you want to
answer the incoming call, press FLASH.
To resume the previous phone conver-
sation, press FLASH again.
The top line of each record shows the
date, time and the number of calls from
that number. The second line shows the
caller’s name, and the third line shows
the caller’s phone number.
If the ET-1102’s Caller ID memory be-
comes full, any new call replaces the
oldest call’s record.
REVIEWING CALLER ID
RECORDS
To review the Caller ID records, lift the
handset and press CALL ID. The number
of new Caller ID records, if any, and the
total number of records appears.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 21 Tuesday, August 17, 1999 4:37 PM
Caller ID Messages
DIALING NUMBERS FROM
A CALLER ID RECORD
Display
Description
To dial a local number stored in a Caller
ID record, recall the record, then press
TALK. If it is a long distance call, press 1
(1 appears before the displayed num-
ber) before you press TALK.
Shows the number of
new Caller ID
records (records you
have not reviewed)
and the total number
of records.
New :XX
Total:XX
Note: If a Caller ID record does not con-
tain a phone number (if it was blocked
by the caller, for example) you cannot
dial from that record.
Private
Name
The caller has
blocked the Caller ID
information from
being sent.
or
Private
Number
STORING A CALLER ID
RECORD TO MEMORY
Unknown
Name
The caller is not
within a Caller ID ser-
vice area.
or
Follow these steps to store the name
and number from a Caller ID record into
a memory location.
Unknown
Number
Appears if there was
an error during the
transmission of
Error
1. Recall the record you want to store,
then press MEM. Select Loca-
tionappears.
Caller ID informa-
tion. Minor electrical
disturbances can
affect Caller ID infor-
mation. Occasional
errors are normal. If
the phone frequently
displays Error,
contact your local
telephone company
or RadioShack store
for assistance.
Appears when you
scroll past the oldest
Caller ID record.
End
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 22 Tuesday, August 17, 1999 4:37 PM
2. Choose a memory location (0–9) by
pressing a number or by repeatedly
pressing s or t, then press SELECT.
DELETING CALLER ID
RECORDS
You can delete Caller ID records individ-
ually or all at once.
To delete a single record, recall it, then
press DELETE. Delete Message?
appears, prompting you to confirm the
deletion. Move the cursor to Yesor No,
then press SELECT or DELETE.
If the selected location is empty, the
phone beeps to confirm that it
stored the number, then the Caller
ID record appears.
If a record exists in the selected lo-
cation, Replace Memory? ap-
pears, prompting you to confirm the
replacement. Move the cursor to
Yesor No, then press SELECT.
To delete all the records at once, recall
any record, then hold down s until the
record totals appear, then press DE-
LETE. DeleteAll?appears, prompt-
ing you to confirm the deletion. Move the
cursor to Yesor No, then press SELECT
or DELETE.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 23 Tuesday, August 17, 1999 4:37 PM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the follow-
ing suggestions might help.
Problem
Suggestion
The phone does not work or works
poorly.
Be sure the base’s phone line cord and
AC adapter are correctly and securely
connected.
Be sure the battery pack in the handset
is connected and charged.
Return the handset to the base for a few
seconds to reset the security access-
protection code.
The display flashes slowly when the
handset is faceup on the base.
Be sure the battery pack in the handset
is properly connected.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical
position.
Be sure the handset’s battery pack is
charged. (If the battery pack power is
too low, it does not have enough power
to light the Low Batteryindication on
the display.)
Low volume or unusual sounds.
Severe noise interference.
Someone has picked up another phone
on the same line. Hang up the other
phone.
Keep the handset away from comput-
ers, remote control toys, wireless micro-
phones, alarm systems, intercoms,
room monitors, fluorescent lights, and
electrical appliances.
Move to another location or turn off the
source of interference.
Hang up and redial the number.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 24 Tuesday, August 17, 1999 4:37 PM
Problem
Suggestion
The phone cannot be operated at a
useful distance from the base
because the signal becomes weak
or noisy (handset’s range has
decreased).
Lift the base’s antenna to a fully vertical
position.
Be sure neither the handset’s nor base’s
antenna is touching a metal surface.
Recharge the battery pack.
The handset battery pack does not
charge.
Check the charging contacts on the
handset and base. If they are dirty, clean
them with a pencil eraser.
Be sure the battery pack is properly con-
nected.
Be sure the handset is properly seated
on the base.
Replace the battery pack (see “Replac-
ing the Battery Pack” on Page 26).
Handset does not ring or receive a
page.
Lift the base’s antenna to a fully vertical
position.
Move the handset closer to the base.
Move the base away from other electri-
cal devices.
Recharge the battery pack.
You have an incoming call, but do
not receive any Caller ID informa-
tion.
Let the phone ring twice before you
answer so the system has time to record
the Caller ID information.
Check that the system is correctly and
securely connected.
Call your phone company to verify that
your Caller ID service is active.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your ET-1102 to your local RadioShack store for assistance.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 25 Tuesday, August 17, 1999 4:37 PM
CARE AND MAINTENANCE
Your RadioShack ET-1102 900 MHz Digital Spread Spectrum Cordless Telephone is
an example of superior design and craftsmanship. The following suggestions will help
you care for your ET-1102 so you can enjoy it for years.
Keep the ET-1102 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the ET-1102 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age battery packs, and distort or melt plastic parts.
Keep the ET-1102 away from dust and dirt, which can cause premature
wear of parts.
Handle the ET-1102 gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the ET-1102 to work improperly.
Use only a battery pack of the required size and recommended type.
Batteries can leak chemicals that damage your ET-1102’s electronic
parts.
Wipe the ET-1102 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the ET-1102.
Modifying or tampering with the ET-1102’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it. If
your ET-1102 is not performing as it should, take it to your local RadioShack store for
assistance. If the trouble is affecting the telephone lines, the phone company can ask
you to disconnect your ET-1102 until you have resolved the problem.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 26 Tuesday, August 17, 1999 4:37 PM
REPLACING THE
BATTERY PACK
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 9, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
4. Replace the cover.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in
a fire because it might explode.
Install the new battery pack as de-
scribed below, then charge it for about
24 hours.
• Do not open or mutilate the battery
pack.
• Be careful not to short the battery
pack by touching the connector’s
pins with conducting materials, such
as rings, bracelets, and keys. The
battery pack or conductor might
overheat and burn.
1. Press down and slide off the battery
pack compartment cover as shown.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
2. Unfasten the plastic retainer strap
and lift the battery pack out of the
compartment, then gently pull on the
battery connector to disconnect it.
Important: This product contains a re-
chargeable nickel-cadmium battery
pack. At the end of the battery pack’s
useful life, it must be recycled or dis-
posed of properly. Contact your local,
county, or state hazardous waste man-
agement authorities for information on
recycling or disposal programs in your
area. Some options that might be avail-
able are: municipal curb-side collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collec-
tion centers, and mail-back programs.
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment, place the battery pack into
the compartment, and refasten the
retainer strap.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 27 Tuesday, August 17, 1999 4:37 PM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To mini-
mize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in telephone line and power
line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1102.fm Page 28 Tuesday, August 17, 1999 4:37 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UCZZ016058Z
9A8
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|