43-1101.fm Page 1 Friday, July 9, 1999 9:32 AM
Cat. No. 43-1101
OWNER’S MANUAL
Please read before using this equipment.
ET-1101
900MHz 40-Channel
Headset Cordless Phone
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 3 Friday, July 9, 1999 9:32 AM
Flash — sends an electronic switchhook
signal for use with special phone services
such as Call Waiting.
tion or cause interference. This possible
lack of privacy can occur with any cord-
less phone.
Tone or Pulse (Rotary) Dialing — lets
you use your phone with tone or pulse di-
aling and lets you easily switch from pulse
to tone dialing for long-distance, bank-by-
phone, or other special services.
We recommend you record your phone’s
serial number here. The number is on the
bottom of the base.
Serial Number: __________________
Belt Clip — lets you carry the keypad on
your belt for easy portability.
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
Hearing-Aid Compatibility — lets you
use your phone with hearing aids that
have a T (telephone) switch.
CAUTION
Your ET-1101 is ETL listed to UL stan-
dards and meets all applicable FCC stan-
dards.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
Important Note: Cordless phones such
as this one require AC power to operate.
When the AC power is off, you cannot dial
out or receive incoming calls using your
ET-1101. To be safe, you should also
have a phone that does not need AC
power to operate (not a cordless phone)
so you can still make and receive calls if
there is an AC power failure.
This symbol is intended to alert you to
the presence of uninsulated dangerous
voltage within the product’s enclosure
that might be of sufficient magnitude to
constitute a risk of electric shock. Do not
open the product’s case.
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the lit-
erature accompanying this product.
Note: Your phone operates on standard
radio frequencies as allocated by the
FCC. It is possible for other radio units
operating nearby on similar frequencies
to unintentionally intercept your conversa-
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 4 Friday, July 9, 1999 9:32 AM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
This telephone complies with Part 68 of
FCC Rules. You must, upon request, pro-
vide the FCC registration number and the
REN to your phone company. These
numbers are shown on the bottom of the
base.
We have designed your phone to conform
to federal regulations, and you can con-
nect it to most telephone lines. However,
each device that you connect to the
phone line draws power from the phone
line. We refer to this power draw as the
device’s ringer equivalence number, or
REN. The REN is on the bottom of the
base.
Note: You must not connect your phone
to any of the following:
• coin-operated systems
• party-line systems
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (three
in rural areas), your phones might not
ring. If ringer operation is impaired, re-
move a device from the line.
• most electronic key phone systems
Warning: Changes or modifications to
this unit not expressly approved by Ra-
dioShack could void the user’s authority
to operate the equipment.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 5 Friday, July 9, 1999 9:32 AM
CONTENTS
Preparation ................................................................................................................... 6
Selecting a Location ................................................................................................ 6
Connecting the Phone ............................................................................................. 6
Connecting and Charging the Battery Pack ............................................................ 7
Attaching the Headset Holder ................................................................................. 8
Adjusting the Headset ............................................................................................. 9
Setting the Ringers On or Off .................................................................................. 9
Setting the Keypad’s Ringer Volume ..................................................................... 10
Setting the Dialing Mode ....................................................................................... 10
Operation .................................................................................................................... 11
Making and Receiving Calls .................................................................................. 11
Adjusting the Headset’s Volume ............................................................................ 11
Changing Channels ............................................................................................... 11
Using Redial .......................................................................................................... 12
Using Mute ............................................................................................................ 12
Using Flash ........................................................................................................... 12
Using Tone Services on a Pulse Line .................................................................... 12
Using Page/Intercom ............................................................................................. 13
Paging the Headset/Keypad ........................................................................... 13
Paging the Base .............................................................................................. 13
Memory Dialing ..................................................................................................... 14
Storing a Number in Memory .......................................................................... 14
Entering a Pause in a Memory Number .......................................................... 15
Dialing a Stored Number ................................................................................ 15
Chain Dialing Service Numbers ...................................................................... 15
Testing Stored Emergency Numbers .............................................................. 15
Troubleshooting ......................................................................................................... 16
Care and Maintenance ............................................................................................... 17
Replacing the Battery Pack ................................................................................... 17
The FCC Wants You to Know ................................................................................ 18
Lightning ................................................................................................................ 19
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 6 Friday, July 9, 1999 9:32 AM
PREPARATION
SELECTING A LOCATION
CONNECTING THE PHONE
You can place the phone’s base on a flat
surface such as desk, shelf, or table. Se-
lect a location that is:
After you select a location for the phone’s
base, follow these steps to connect it to
AC power and to the phone line.
• near an easily accessible AC outlet
• near a telephone line jack
Caution: You must use a Class
2 power source that supplies 12
!
volts DC and delivers at least
500 mA. Its center tip must be set to posi-
tive and its plug must fit the ET-1101's DC
12V 500mA jack. The supplied adapter
meets these specifications. Using an
adapter that does not meet these specifi-
cations could damage the ET-1101 or the
adapter.
• out of the way of normal activities
• away from electrical machinery, elec-
trical appliances, metal walls, filing
cabinets, wireless intercoms, security
alarms, and room monitors
The base’s location affects the phone’s
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
Notes:
• Your telephone connects directly to a
modular telephone line jack. If your
phone line jack is not a modular jack,
you can update the wiring yourself,
using jacks and adapters available at
your local RadioShack store. Or, you
can let the phone company update
the wiring for you.
1. Plug one end of the supplied modular
cord into the TEL. LINE jack on the
back of the base.
• The USOC number of the jack to be
installed is RJ11C.
2. Plug the modular cord’s other end
into a modular phone line jack.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 7 Friday, July 9, 1999 9:32 AM
3. Plug the supplied AC adapter’s barrel
plug into the DC 12V 500mA jack on
the back of the base.
To charge the battery pack, place the
keypad in the front charging slot on the
base. The CHARGE/IN USE indicator on
the base lights.
4. Plug the adapter into a standard AC
outlet.
Rear
Front
Charging
Slot
Charging
Slot
5. Lift the base’s antenna to a vertical
position.
CONNECTING AND
CHARGING THE BATTERY
PACK
The ET-1101 comes with a rechargeable
nickel-cadmium battery pack. You must
connect the battery pack and charge it for
at least 15 hours before you use the
phone.
To charge a spare battery pack, place it in
the rear charging slot with its latch end
facing down and its contacts toward the
rear of the base. The CHARGE indicator
lights.
To connect the battery pack, line up the
slots on the battery pack with the posts on
the back of the keypad. Press down and
slide the battery pack forward until the
latch clicks.
Spare battery packs (RadioShack Cat.
No. 23-810, not supplied) are available at
your local RadioShack store.
Recharge the battery pack when the LOW
BATT indicator on the keypad flashes.
LOW BATT
Indicator
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 8 Friday, July 9, 1999 9:32 AM
• If the battery pack becomes com-
pletely discharged or the base loses
power while the handset is away from
it, the security access-protection code
needs to be reset. To reset the securi-
ty code, place the handset on the
base for about 5 seconds. If it was the
handset that lost power, leave it on
the base to charge the battery pack.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear error tones (three
beeps).
If you hear the error tones, return the
keypad to the base for about 5 sec-
onds to reset the security access-
protection code.
• If you are not going to use your phone
for an extended period of time, dis-
connect its battery pack. This helps
increase the battery pack’s usable
life.
• About once a month, fully discharge
the battery pack by keeping the
phone off the base until the LOW
BATT indicator flashes. Otherwise,
the battery pack loses its ability to
fully recharge.
ATTACHING THE HEADSET
HOLDER
• If the CHARGE/IN
USE indicator does
not light when you
place the keypad
on the base, be
sure the battery
Insert the tabs on the headset holder into
the slots on the base and snap it into
place.
Charging Contacts
pack
and
AC
adapter are cor-
rectly and securely
connected.
Also,
check the charging
contacts on the
keypad and base. If
the contacts are
dirty or tarnished,
clean them with a
pencil eraser.
Charging Contacts
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 9 Friday, July 9, 1999 9:32 AM
Note: When you are not using the head-
set, place it on the headset hanger. Oth-
erwise (if you just lay it down on a flat
surface, for example), you might have to
repeat these adjustments.
SETTING THE RINGERS ON
OR OFF
The ringer switch on the right side of the
base controls both the keypad and base
ringers. To have the ET-1101 ring when a
call comes in, set RINGER to ON. To turn
the ringer off, set RINGER to OFF.
ADJUSTING THE HEADSET
1. Place the headset on your head with
the earpiece over either ear.
2. Adjust the headset band until it rests
with almost no pressure on your ear
and the top of your head.
RINGER
If the headset is loose, adjust it
inward slightly to tighten it. If the
headset is tight, gently pull the head-
set band out to loosen it.
With RINGER set to OFF, the phone does
not ring, but you can still make outgoing
calls. If you hear an extension telephone
ring, you can answer the incoming call on
this phone. The CHARGE/IN USE indica-
tor on the base and the IN USE indicator
on the keypad flash until you answer the
call.
3. Hold the headset in place, and adjust
the microphone boom until it is about
even with your chin. Experiment until
you find the most comfortable posi-
tion.
Caution: The microphone boom
swivels on the headset. Do not bend
the microphone boom while you
adjust it.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 10 Friday, July 9, 1999 9:32 AM
SETTING THE KEYPAD’S
RINGER VOLUME
You can adjust the keypad’s ringer vol-
ume by repeatedly pressing RINGER AD-
JUST when the phone is not in use. The
keypad rings with the current volume
(high, medium, or low) as you select it.
Note: You cannot adjust the base’s ringer
volume.
2. Press TALK so the IN USE indicator
lights and listen for a dial tone.
IN USE
Indicator
RINGER
ADJUST
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
SETTING THE DIALING
MODE
Set TONE-PULSE on the side of the base
for the type of service you have. If you are
not sure which type you have, do this sim-
ple test after charging the battery pack.
If the dial tone stops, you have touch-
tone service. If the dial tone contin-
ues, you have pulse service.
1. Set TONE-PULSE to TONE.
4. If you have tone service, leave TONE-
PULSE set to TONE. If you have pulse
service, set TONE-PULSE to PULSE.
5. To hang up, place the keypad on the
base or press TALK.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 11 Friday, July 9, 1999 9:32 AM
OPERATION
• If interference is severe, the keypad
might lose communication with the
base and the call might disconnect. If
this happens, return the keypad to the
base for about five seconds to reset
the security access-protection code.
MAKING AND RECEIVING
CALLS
Before you use the phone, put the head-
set on and adjust it as needed.
To make a call, lift the keypad off the
base, then press TALK. You hear the dial
tone and the IN USE indicator lights. Dial
the number you want to call.
ADJUSTING THE
HEADSET’S VOLUME
To answer a call, lift the keypad off the
base, then press TALK. The IN USE indi-
cator lights.
To adjust the headset’s volume, repeat-
edly press VOLUME ▲ or VOLUME ▼ dur-
ing a call until the sound level is
comfortable. You can set the headset’s
volume to one of eight levels, and it will
remain set even after you hang up.
TALK
CHANGING CHANNELS
VOLUME
Every time you press TALK, the ET-1101
automatically selects a clear channel from
the 40 it uses for communication between
the headset and the base. If you hear in-
terference during a call, repeatedly press
CHANNEL to change the channel until you
get a clear one.
To end a call, press TALK or place the
keypad on the base.
Notes:
• When you press a button, a single
tone indicates that the phone has ac-
cepted the command. Three tones in-
dicate that you pressed a button in
error, you are out of range, or there is
too much interference. If there is se-
vere interference, see “Changing
Channels.”
CHANNEL
REDIAL
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 12 Friday, July 9, 1999 9:32 AM
USING REDIAL
USING FLASH
To quickly redial the last number dialed,
press TALK then REDIAL.
FLASH provides the electronic equivalent
of a switchhook signal for special phone
services such as Call Waiting.
Notes:
TONE
• The redial memory holds up to 32
digits, so you can redial long-distance
as well as local numbers.
• The redial memory can also store
tone entries (see “Using Tone Ser-
vices On a Pulse Line”) and pause
entries (see “Entering a Pause in a
Memory Number” on Page 15).
FLASH
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
USING MUTE
To talk to someone else in the room with-
out the person on the other end of the
phone line hearing your conversation,
press MUTE.
Note: If you do not have any special
phone services, pressing FLASH might
disconnect your current call.
USING TONE SERVICES ON
A PULSE LINE
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these tone
services by following these steps.
MUTE
Press MUTE again to resume your phone
conversation.
1. Dial the service’s main number.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 13 Friday, July 9, 1999 9:32 AM
2. When the service answers, press
TONE. Any additional numbers you
dial are sent as tone signals.
3. After you complete the call, press
TALK or return the keypad to the
base. The phone automatically resets
to pulse dialing.
INTERCOM
To answer the page, press INTERCOM on
the keypad before the INTERCOM indica-
tor stops flashing (about 6 seconds).
When you finish your intercom conversa-
tion, press INTERCOM again to hang up.
USING PAGE/INTERCOM
You can send a page and use the ET-
1101 as an intercom between the base
and the headset/keypad. This is useful if
the headset/keypad is away from the
base and you want to locate it, or if you
want to have a conversation between
someone using the headset/keypad and
someone at the base.
Paging the Base
To page the base, press INTERCOM on
the keypad. The base rings nine times
and its INTERCOM indicator flashes.
Paging the Headset/Keypad
To page the person who has the headset/
keypad or to locate the headset/keypad
when the phone is not in use, press IN-
TERCOM on the base. The keypad rings
three times and its INTERCOM indicator
flashes. To have the keypad ring for a
longer time, hold down INTERCOM for 3
seconds. The keypad rings about 9 times.
INTERCOM Indicator
To answer the page, press INTERCOM on
the base before the INTERCOM indicator
stops flashing (about 18 seconds). To end
the intercom conversation, press INTER-
COM again.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 14 Friday, July 9, 1999 9:32 AM
1. While the phone is not in use, press
MEMORY DIALING
MEMORY.
You can store up to 10 numbers of up to
16 digits each in the ET-1101’s memory.
2. Dial the number you want to store.
3. Press MEMORY again.
Notes:
4. Press the memory location number
(0–9) you want to use. The keypad
sounds one long tone to confirm that
the phone number has been stored.
• To keep your accounts secure, we
recommend you do not store your
personal access code for services
such as bank-by-phone in a memory
location.
Note: If you do not hear a long tone,
you did not successfully store the
number. Start again at Step 1.
• When storing numbers for special
services (such as alternate long dis-
tance or bank-by-phone), store the
service’s main phone number in one
memory location and numbers for ad-
ditional information in other locations.
5. Pull out the memory index card at the
bottom of the base and write the
associated name or stored number
next to the location number. We rec-
ommend you use a pencil so you can
change it later.
Storing a Number in Memory
Note: If you do not press any button on
the keypad within about 10 seconds, 3
beeps sound and the phone exits the
memory storing process. Start again from
Step 1.
MEMORY
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 15 Friday, July 9, 1999 9:32 AM
Notes:
Dialing a Stored Number
• If you receive a call while you are
storing a number in memory, press
TALK to answer the call. After the call,
begin again at Step 1.
Press TALK. When you hear the dial tone,
press MEMORY then the memory location
number. The phone dials the number.
• To change a number stored in mem-
ory, simply store a new number in that
memory location.
Chain Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long distance
or bank by phone), store each group of
numbers in its own memory location.
Entering a Pause in a Memory
Number
When calling special services, dial the
service’s main number first. Then, at the
appropriate place in the call, press MEMO-
RY, then the number for the location
where the additional numbers are stored.
In some telephone systems, you must dial
an access code (9, for example) and wait
for the second dial tone before you can
dial an outside number. You can store the
access code with the phone number.
However, you should also store a pause
after the access code to allow the outside
line time to connect. To do so, press
PAUSE to enter a 3-second pause after
entering the access code. For a longer
pause, press PAUSE again.
Note: If you use pulse dialing, be sure
you have stored a tone entry in another
memory location (see “Using Tone Ser-
vices on a Pulse Line” on Page 12).
Testing Stored Emergency
Numbers
If you store an emergency service’s num-
ber (police department, fire department,
ambulance) and you want to test the
stored number, make the test call during
the late evening or early morning to avoid
peak demand periods. Remain on the line
to explain the reason for your call.
PAUSE
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 16 Friday, July 9, 1999 9:32 AM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the following
suggestions might help.
Problem
Suggestion
The keypad does not work. Move the keypad closer to the base.
Raise the base’s antenna to a vertical position.
Ensure the phone’s modular cord and the AC adapter are
correctly and securely connected.
Recharge the keypad’s battery pack. (If battery power is
too low, the LOW BATT indicator does not light.)
Reset the security access-protection code by placing the
keypad on the base for about five seconds.
Call is noisy.
Keep the headset and base away from interference
sources such as computers, remote control toys, wire-
less alarm systems, wireless intercoms and room moni-
tors, fluorescent lights, and electrical appliances. If the
interference is severe, turn off the interfering device.
Move the keypad closer to the base.
Hang up and redial the number.
Press CHANNEL to change the channel.
The range decreases.
Ensure the base’s antenna is raised and is not touching a
metal surface.
Recharge the keypad’s battery pack.
Can receive calls, but can- Set TONE-PULSE correctly for the type of service you
not make calls. have (see “Setting the Dialing Mode” on Page 10).
If you still have problems, disconnect the phone. If other phones on the same line work
properly, the fault is in this phone or its installation. If you cannot locate the problem,
take your ET-1101 to your local RadioShack store for assistance.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 17 Friday, July 9, 1999 9:32 AM
CARE AND MAINTENANCE
To enjoy your RadioShack ET-1101 900
MHz 40-Channel Headset Cordless
Phone for a long time:
REPLACING THE BATTERY
PACK
• Keep the phone dry. If it gets wet,
wipe it dry immediately.
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 7, the battery pack should last
about a year. If the battery pack does not
hold a charge for more than 2 hours after
an overnight charge, replace it. You can
order a replacement battery pack (Cat.
No. 23-810) through your local Ra-
dioShack store.
• Use and store the phone only in nor-
mal temperature environments.
• Handle the phone gently and care-
fully. Don’t drop it.
• Keep the phone away from dust and
dirt.
• Wipe the phone with a damp cloth oc-
casionally to keep it looking new.
Note: To avoid losing numbers stored in
memory, try to install and begin charging
the new battery pack within 2 minutes of
removing the old one.
Modifying or tampering with the phone’s
internal components can cause a mal-
function and invalidate its warranty. If
your phone is not performing as it should,
take it to your local RadioShack store for
assistance. If the trouble is affecting the
telephone lines, the phone company can
ask you to disconnect your phone until
you have resolved the problem.
1. To remove the old battery pack, press
the latch release, then slide the bat-
tery pack back and lift it from the key-
pad.
Latch Release
2. To connect the new battery pack, line
up the slots on the battery pack with
the posts on the keypad. Press down
and slide it forward until the latch
clicks.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 18 Friday, July 9, 1999 9:32 AM
3. Charge the battery pack for 15 hours
before using it.
THE FCC WANTS YOU TO
KNOW
Cautions:
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of your
right to file a complaint with the FCC.
• Be careful not to short the battery
pack by touching it with conducting
materials, such as rings, bracelets,
and keys. The battery pack or con-
ductor might overheat and burn.
• Do not dispose of the battery pack in
a fire because it might explode.
• Do not open or mutilate the battery
pack.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take the
necessary steps to prevent interruption of
your telephone service.
Note: If you have trouble replacing the
battery pack, take the phone to your local
RadioShack store for assistance.
Important: Your telephone contains a re-
chargeable nickel cadmium battery pack.
At the end of the battery pack’s useful life,
it must be recycled or disposed of proper-
ly. Contact your local, county, or state
hazardous waste management authori-
ties for information on recycling or dispos-
al programs in your area. Some options
that might be available are: municipal
curb-side collection, drop-off boxes at re-
tailers such as your local RadioShack
store, recycling collection centers, and
mail-back programs.
This equipment complies with the limits
for a Class B digital device as specified in
Part 15 of FCC Rules. These limits pro-
vide reasonable protection against radio
and TV interference in a residential area.
However, your equipment might cause
TV or radio interference even when it is
operating properly. To eliminate interfer-
ence, you can try one or more of the fol-
lowing corrective measures:
• Reorient or relocate the receiving an-
tenna.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 19 Friday, July 9, 1999 9:32 AM
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical cir-
cuits for the equipment and the radio
or TV.
Consult your local RadioShack store if the
problem still exists.
LIGHTNING
Your telephone has built-in lightning pro-
tection to reduce the risk of damage from
surges in telephone line and power line
current. This lightning protection meets or
exceeds FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common. Never-
theless, if you live in an area that has se-
vere electrical storms, we suggest that
you unplug your phone before storms to
reduce the possibility of damage.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1101.fm Page 20 Friday, July 9, 1999 9:32 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/99
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
07A99
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|