43-5520.fm Page 1 Friday, July 21, 2000 8:01 AM
900 MHz Digital Spread
Spectrum Dual Keypad
Cordless Telephone
with Caller ID/Call Waiting ID
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 3 Friday, July 21, 2000 8:01 AM
Note:
This phone has been tested and found to
comply with all applicable UL and FCC stan-
dards.
You must not connect your phone to:
• coin-operated systems
• party-line systems
IMPORTANT CALLER ID
INFORMATION
• most electronic key telephone systems
Important:
To use the phone's Caller ID and Call Wait-
ing with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. For this reason, the phone
should not be your only telephone. To be
safe, you should also have a phone that
does not require AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an AC
power failure.
• caller's number only
• caller's name only
• caller's name and number.
• Some cordless phones operate at fre-
quencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
READ THIS BEFORE
INSTALLATION
We have designed your phone to conform to
federal regulations, and you can connect it to
most telephone lines. However, each phone
(and each device, such as a telephone or an-
swering machine) that you connect to the
telephone line draws power from the tele-
phone line. We refer to this power draw as
the device's ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
• Your cordless phone operates on stan-
dard radio frequencies, as allocated by
the FCC. Even though your phone's
access protection code prevents unau-
thorized use of your phone line, it is pos-
sible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conver-
sations and/or cause interference. This
possible lack of privacy can occur with
any cordless phone.
If you use more than one phone or other de-
vice on the line, add up all of the RENs. If the
total is more than five (or three in rural ar-
eas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
THE FCC WANTS YOU TO
KNOW
Your phone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your telephone company. Both numbers are
on the bottom of your phone.
In the unlikely event that your phone causes
problems on the phone line, the phone com-
pany can temporarily discontinue your ser-
vice. If this happens, the phone company
attempts to notify you in advance. If advance
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 4 Friday, July 21, 2000 8:01 AM
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Consult your local RadioShack store if the
problem still exists.
IMPORTANT SAFETY
INSTRUCTIONS
Also, the phone company can make changes
to its lines, equipment, operations, or proce-
dures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interrup-
tion of your telephone service.
When using your telephone equipment, ba-
sic safety precautions should always be fol-
lowed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the net-
work interface.
Lightning damage is not common. Neverthe-
less, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
6. Use caution when installing or modifying
telephone lines.
FCC STATEMENT
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
The phone complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reason-
able protection against radio and TV interfer-
ence in a residential area. However, your
equipment might cause TV or radio interfer-
ence even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid clean-
ers or aerosol cleaners. Use a damp
cloth for cleaning.
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 5 Friday, July 21, 2000 8:01 AM
11. Slots and openings in the cabinet and
the back or bottom are provided for ven-
tilation. To protect it from overheating,
these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
• When the power cord plug is damaged
or frayed.
• If liquid has been spilled into the prod-
uct.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are cov-
ered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a quali-
fied technician to restore the product to
normal operation.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power com-
pany.
• If the product has been dropped or the
cabinet has been damaged.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
• If the product exhibits a distinct change
in performance.
14. Do not overload wall outlets and exten-
sion cords as this can result in a risk of
fire or electric shock.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltage or other risks. Incor-
rect reassembly can cause electric
shock when the product is subsequently
used.
CAUTION:
TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
.
THESE INSTRUCTIONS
1. Use only the appropriate type and size
of battery pack specified in the instruc-
tion manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following condi-
tions:
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 6 Friday, July 21, 2000 8:01 AM
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
4. Exercise care in handling the battery
pack in order not to short it with conduct-
ing materials such as rings, bracelets,
and keys. The battery or conductor may
overheat and cause burns.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
SAVE THESE
INSTRUCTIONS
ˆ Features
Your Sprint 900 MHz Digital Spread Spec-
trum Dual Keypad Cordless Telephone uses
the most advanced cordless telephone tech-
nology to give you superior audio quality and
extended range.
Dual Keypads
the handset and base let you use either key-
pad to operate the phone.
— a full set of keys on both
Speakerphone
calls without using the handset.
— lets you make or answer
The phone’s Caller ID records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers. And, if you
subscribe to Call Waiting with Caller ID, the
phone shows you the incoming caller infor-
mation, even when you are already on the
phone.
Lighted Handset Keypad
— Lights when
you press any key or receive a call, making
the phone easy to use, even in total dark-
ness.
Network Service
— supports the advanced
calling features such as Return Call, Repeat
Dial, and Cancel Call Waiting.
3-Line Liquid Crystal Display with Back-
Your phone has these features:
light
— lets you view an entire Caller ID
record on one screen.
900 MHz Operation
— provides longer
range and less interference than many other
cordless phones.
30-Number Memory Dialing
— lets you
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dial-
ing.
Spread Spectrum Technology
— spreads
the signal across several frequencies, for
added security during your phone conversa-
tions.
Two-Way Intercom/Paging System
— lets
you send a signal from the base to the hand-
set (or from the handset to the base) to page
someone or locate the handset when it is
away from the base. If someone answers,
you can use the phone as an intercom.
Caller ID Memory
— stores up to 50 Caller
ID records.
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 7 Friday, July 21, 2000 8:01 AM
Headset Jack
20 Channels
— lets you connect an option-
— automatically selects a clear
al headset (available from your local Ra-
dioShack store) for hands-free convenience.
channel when you make or answer a call.
Security Access-Protection Code
— auto-
Facedown or Faceup Handset Charging
— you can place the handset on the base
face down or face up (to show the Caller ID
display, for example).
matically prevents other cordless phone us-
ers from using your phone line.
Redial
— lets you quickly redial any of the
three last numbers dialed on the handset
and the last number dialed on the base.
Volume Control
— lets you adjust the vol-
ume you hear through the handset.
Flash
— sends an electronic switchhook sig-
Adjustable Ringers
volumes for the handset and base ringers.
— you can set different
nal for use with special phone services, such
as Call Waiting.
Auto Talk
Tone/Pulse Dialing
— lets you use your
— lets you set the handset so you
can answer a call by simply lifting the hand-
set from the base or by pressing any key
when the handset is away from the base.
phone with either type of service and you can
quickly switch from pulse to tone dialing for
long-distance, bank-by-phone, or other spe-
cial services.
Ample Talk and Standby Time
— the sup-
Hearing-Aid Compatibility
your phone with hearing aids that have a T
(telephone) switch.
plied battery (when fully charged) provides
about 7 hours of talk time or 7 days of stand-
by time.
— lets you use
ˆ Installation
The base’s location affects the phone’s
range. If you have a choice of several loca-
tions, try each to see which provides the best
performance.
MOUNTING THE PHONE
You can place the phone’s base on a desk or
table, mount it on a standard wall plate or di-
rectly on a wall. Choose a location that is:
Cautions:
• near an AC outlet
You must use a Class 2 power
• near a modular telephone line jack
• out of the way of normal activities
source that supplies 9V DC
and delivers at least 350 mA.
Its center tip must be set to positive and
!
DC IN 9V
its plug must fit the phone's
• away from electrical machinery, electri-
cal appliances, metal walls or filing cabi-
nets, wireless intercoms, alarms, and
room monitors
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
• away from other cordless phones
7
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 8 Friday, July 21, 2000 8:01 AM
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you dis-
connect it from the phone.
2. Plug one end of the supplied short mod-
TEL LINE
ular cord into the
back of the base.
jack on the
3. Insert the supplied AC adapter’s barrel
DC IN 9V
plug into the
jack.
Note:
Your telephone connects directly to a
modular telephone line jack. If your phone
line jack is not a modular jack, you can up-
date the wiring yourself, using jacks and
adapters available at your local RadioShack
store. Or, you can let the phone company up-
date the wiring for you.
4. Route the adapter and modular cords
through the grooves on the bracket.
The USOC number of the jack to be installed
is RJ11C (RJ11W for a wall plate).
On a Desk Top, Shelf, or Table
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the phone down-
ward to secure it.
1. Plug one end of the supplied long modu-
TEL LINE
lar cord into the
back of the base.
jack on the
2. Plug the modular cord’s other end into a
modular telephone line jack.
3. Insert the supplied AC adapter’s barrel
DC IN 9V
plug into the
of the base.
jack on the back
4. Route the adapter’s cord through the
strain relief slot on the bottom of the
base.
5. Plug the adapter into a standard AC out-
let.
6. Plug the adapter into a standard AC out-
let.
6. Lift the base’s antenna to a vertical posi-
tion.
7. Press and lift out the handset holder.
Rotate it 180°, then snap it back into
place so it holds the handset.
On a Wall Plate or Wall
1. Insert the two tabs at the top of the nar-
row end of the supplied bracket into the
base’s upper tab slots, then press down
on the bracket’s latches and insert them
into the lower slots.
8. Lift the base’s antenna to a vertical posi-
tion.
8
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 9 Friday, July 21, 2000 8:01 AM
Note:
To mount the phone directly on a wall,
1. Press down and slide off the battery
pack compartment cover.
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base.
Follow the steps under “On a Wall Plate or
Wall” on Page 8, then apply these additional
instructions.
2. Lift the battery pack out of the compart-
ment.
1. Drill two holes 315/16 inches
3
/16"
(100 mm) apart. Then thread
a screw into each hole, let-
3. Plug the battery pack's connector into
the socket in the compartment, (the con-
nector fits only one way), replace the
battery pack, and replace the cover.
15
3 /16"
ting the heads extend about
3
/16 inch (5 mm) from the
wall.
2. Plug one end of the supplied long modu-
TEL LINE
lar cord into the
jack on the
back of the base and route the adapter
cable and modular cords through the
grooves on the bracket.
To charge the battery pack, place the hand-
set either faceup or facedown on the base.
The CHARGE/IN USE indicator on the base
lights and Total:00 appears.
3. Align the bracket’s keyhole slots with the
mounting screws and slide the phone
downward to secure it.
Recharge the battery pack when Low Bat-
tery flashes.
Important:
Be sure the battery pack is prop-
erly connected before you try to charge it.
The CHARGE/IN USE indicator lights when
the handset is on the base, even if the bat-
tery pack is not connected.
Notes:
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
TALK
hear a beep when you press
.
Return the handset to the base for about
5 seconds to reset the security access-
protection code.
The phone comes with a rechargeable
nickel-cadmium battery pack in the hand-
set. Before using your phone, you must
connect the battery pack, then charge it for
about 24 hours.
• If the base loses power for 60 minutes
while the handset is away from it or the
handset’s battery pack is completely dis-
charged, the security access-protection
code might be lost. To reset the code,
9
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 10 Friday, July 21, 2000 8:01 AM
return the handset to the base for about
5 seconds.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
• Using a pencil eraser, clean the charg-
ing contacts on the handset and base
about once a month.
Important:
The EPA certified
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
• If the battery pack becomes weak during
a call, the handset beeps every 3 sec-
onds and Low Battery flashes. When
this happens, you cannot make another
call on the phone until you recharge the
battery pack.
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a con-
venient alternative to placing used Ni-Cd bat-
teries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-843-
7422) for information on Ni-Cd battery recy-
cling and disposal bans/restrictions in your
area. RadioShack’s involvement in this pro-
gram is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
• About once a month, fully discharge the
battery by keeping the handset off the
base until Low Battery flashes. Oth-
erwise, the battery pack loses its ability
to fully recharge.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• If you are not going to use your phone
for an extended period of time, discon-
nect the battery pack. This increases the
battery pack's usable life.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an over-
night charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Warning:
Dispose of the old battery pack
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 5
for additional information on proper battery
handling).
10
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 11 Friday, July 21, 2000 8:01 AM
A QUICK LOOK AT THE HANDSET
Note:
The handset window has a plastic film on it to protect it during shipment. Carefully peel
off the film before using your phone for the first time.
Press VOL/CID
or
to adjust
8
9
the handset volume (see “Adjusting
the Handset Volume” on Page 13),
set the ringer tone/volume (see
“Setting the Ringer Tone/Volume”
on Page 12), view Caller ID records
(see “Caller ID Operation” on
Page 19), or select options.
Use TALK to make a
call (see “Making and
Receiving Calls” on
Page 13).
Use CALL ID to review
the Caller ID records.
Press INTCM to page someone at
the base or transfer a call to the
base (see “Using Page/Intercom” on
Page 15).
Press FLASH to use
the phone’s flash
function (see “Using
Flash” on Page 15).
Press MENU to use the telephone
company’s network service (see
“Using the Phone Company’s Net-
work Service” on Page 21).
Press TONE
to use your phone
6
*
company’s special tone services on
a pulse line (see “Using Tone Ser-
vices on a Pulse Line” on Page 15).
Press DEL to Delete Caller ID
records (see “Deleting Caller
ID Records” on Page 20) or to
erase information if you make
a mistake.
Use MEM to store or recall
names and numbers in memory
(see “Memory Dialing” on
Page 16).
Press SELECT/CHANNEL to
select the phone’s channels
(see “Selecting the Channel”
on Page 13) and other options.
Press RDL/PAUSE to select a phone
number so you can redial it (see
“Using Redial” on Page 14) or store
a pause in a number (see “Entering
a Pause” on Page 18).
TALK
2. Lift the handset, press
for a dial tone.
, and listen
SETTING THE
DIALING MODE
3. Press any number except 0.
DIAL MODE
Set
on the back of the base for
the type of service you have. If you are not
sure which type you have, once the battery
pack is fully charged, do this test.
Note:
If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
DIAL MODE
T
1. Be sure
is set to (tone).
11
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 12 Friday, July 21, 2000 8:01 AM
not press the access code number
either.
TURNING AUTO
TALK ON/OFF
If the dial tone stops, you have touch-
Your phone is preset so you must press
DIAL MODE
T
tone service. Leave
set to .
TALK
when you lift the handset from the base
to answer a call. With auto talk turned on,
you can answer a call by just lifting the hand-
set from the base. If the handset is away
from the base, you can answer by pressing
any key.
If the dial tone continues, you have
DIAL MODE
P
pulse service. Set
(pulse).
to
SETTING THE RINGER
TONE/VOLUME
Follow these steps to turn auto talk on or off.
CALL ID
1. Lift the handset and hold down
.
You can select one of four different ringer
tone/volume settings on the handset. Re-
A menu appears with Auto Talk
selected.
VOL/CID 8
9
peatedly press
or
(except
during a call) to select the desired ringer set-
ting. Each time you press a button, the
phone rings at the selected setting and the
display shows Ringer A High, Ringer A
Low, Ringer B High, or Ringer B Low.
SELECT/CHANNEL
2. Press
to change the
auto talk setting. On or Off appears
indicating the selected setting.
3. Return the handset to the base or press
CALL ID
to store the new setting.
Note:
VOL/CID 8
Pressing
when the phone
VOL/CID 9
is set to Ringer A High or
when the phone is set to Ringer B Low
does not change the setting. Press the oppo-
site arrow key to change the setting.
TURNING CALLER ID/
CALL WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Call-
er ID information for an incoming call even
while you are using the phone.
RING
To set the base’s ringer volume, set
VOL
OFF LO
, or
on the back of the base to
,
HI
.
Notes:
Follow these steps to turn the Caller ID/Call
Waiting feature on or off.
RING VOL
OFF
, the
• When you set
to
base (and the handset if it is on the
base) does not ring but another phone
connected to the same line rings. If the
handset is away from the base, the
handset also rings.
CALL ID
1. Lift the handset and hold down
.
2
VOL/CID 9
to select CIDCW
2. Press or
(Caller ID/Call Waiting).
SELECT/CHANNEL
3. Press
to change the
Caller ID/Call Waiting setting. On or
Off appears indicating the selected
setting.
• When you set the auto talk function to
off, the handset rings when you lift the
handset from the base. See “Turning
Auto Talk On/Off.”
Return the handset to the base to store the
new setting.
12
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 13 Friday, July 21, 2000 8:01 AM
3
VOL/CID 9
2. Press or
twice to select
STORING YOUR
AREA CODE
Area Code.
SELECT/CHANNEL
3. Press
,
then enter
You can store your local area code in the
phone’s Caller ID record so it does not show
the area code if the received call is from your
local area. If for some reason you need to
dial the area code (or store it in the memory),
you can add it afterwards. See “Adding/De-
leting the Area Code” on Page 20.
your three-digit area code. If you make a
mistake, repeatedly press 6 or 7 to
move the cursor over the incorrect digit,
then enter the correct number.
Note:
If an area code is already stored, it ap-
pears. To delete the area code, press
DEL
three times. Then enter your area code. Or
you can use 6 or 7 to move the cursor and
edit the area code.
Note:
If your calling area requires 10-digit di-
aling including area code, do not enter the
area code but leave this option blank.
SELECT/CHANNEL
Press
to store the area
or return the hand-
Follow these steps to store your area code.
CALL ID
code, then press
set to the base to clear the display.
CALL ID
1. Lift the handset and hold down
.
ˆ Operation
any key. Talk and the current volume set-
ting appear.
MAKING AND RECEIVING
CALLS
To end a call, place the handset on the base
To make a call, lift the handset and press
TALK
or press
.
TALK
. Talk and the current volume setting
(see “Adjusting the Handset Volume”) ap-
pear on the handset’s display, and the
CHARGE/IN USE indicator on the base
lights. Then dial the number. The number ap-
pears on the handset as you dial, then the
call’s elapsed time appears.
Selecting the Channel
The phone has 20 channels. If the call
seems to disconnect for no reason during a
SELECT/CHANNEL
call, press
on the handset
to select a different channel. Scanning ap-
pears while your phone searches for a clear
channel.
You can also dial the number before you
TALK
press
.
DEL
If you make a mistake, press
until the in-
Adjusting the Handset Volume
correct entry is erased, then enter the correct
number. To delete the entire number, hold
To adjust the handset’s volume during a call,
DEL
down
for at least 1 second.
VOL/CID 8
9
press
or
until you reach the
desired volume level. Volume Maximum,
Volume High, Volume Medium, or
Volume Low appears.
When you receive a call, Incoming Call
appears. To answer it, lift the handset from
TALK
the base and press
. If auto talk is on,
just lift the handset from the base or press
13
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 14 Friday, July 21, 2000 8:01 AM
Once you set the volume level, the setting is
maintained even after you hang up the
phone.
During the call, one person can hang up and
another person can continue the call at the
other keypad. Or, both people can hang up
at the same time to end the call.
Note:
VOL/CID 8
When you press
while the
while the
VOL/CID 9
Note:
If you hear a high-pitched noise from
volume is maximum or
volume is low, the setting does not change
and the phone beeps three times.
the base’s speaker, the handset and the
base are too close together.
USING THE
SPEAKERPHONE
USING HOLD
HOLD
Press
to put a speakerphone call on
hold. The HOLD indicator lights. While a call
is on hold, you can make an intercom call
(see “Using Page/Intercom” on Page 15) be-
tween the handset and the base without dis-
connecting the call.
To make or answer a call using the speaker-
SPEAKER
phone, press
. The SPEAKER indi-
cator lights. When you hear a dial tone, dial
the number.
To set the speakerphone’s volume, slide
To release a call from hold, lift the handset
VOLUME
on the right side of the base.
TALK
SPEAKER
HOLD
or on
and press
, press
SPEAKER
To end a speakerphone call, press
again.
the base, or pick up any extension phone on
the same line.
Switching Between the Handset
and Speakerphone
USING MUTE
While talking on the speakerphone, you can
temporarily turn off the phone’s microphone
To switch to the speakerphone while you are
MUTE
by pressing
so the other party cannot
SPEAKER
using the handset, press
on the
hear you. The SPEAKER indicator flashes.
base. When you hear the conversation or
TALK
dial tone on the speakerphone, press
on the handset.
MUTE
SPEAKER
to resume your
Press
or
conversation.
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
Note:
If the phone is close to loud noises
while you are using the speakerphone, the
phone might not switch to let you hear the
person on the other end of the line. If this
TALK
SPEAKER
.
base, press
, then press
MUTE
happens, press
to turn off the micro-
Using Both the Handset
and Speakerphone
phone so you can hear the caller. Press
MUTE
again to speak.
If someone else is using the speakerphone,
USING REDIAL
TALK
press
versation.
on the handset to join the con-
You can quickly dial any of the last three
numbers you dialed recently on the handset.
Lift the handset and repeatedly press
If someone else is using the handset, press
RDL/
SPEAKER
on the base to join the conversa-
PAUSE
until the number you want to dial dis-
tion.
14
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 15 Friday, July 21, 2000 8:01 AM
TALK
DIAL MODE
P
plays. Then press
the number.
and the phone dials
1. Be sure
is set to .
2. Dial the service’s main number.
To dial the last number dialed using the
3. When the service answers, press
/
SPEAKER
REDIAL
.
base, press
then
*
TONE/6
TONE
on the
on the handset (
Notes:
base). Any additional numbers you dial
are sent as tone signals.
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
When you hang up, the phone automatically
resets to pulse dialing.
REDIAL
using
on the base’s keypad, and
vice versa.
USING PAGE/INTERCOM
• On the handset, you can also press
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to converse with someone through
the intercom.
RDL/PAUSE
after pressing
the last number dialed.
TALK
to dial
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
IN-
To page the base from the handset, press
TCM
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 18.
. Paging Base appears, and the base
INTCM/
or
on the base to answer the page. In-
SPEAKER
and handset ring. Press
PAGE
tercom appears.
USING FLASH
IN-
To page the handset from the base, press
FLASH
performs the electronic equivalent of
TCM/PAGE
. The handset and base ring, and
a switchhook operation for special services,
such as Call Waiting.
TALK
INTCM
on
Paging appears. Press
the handset to answer the page. Intercom
or
appears.
For example, if you have Call Waiting, press
FLASH
to answer an incoming call without
TALK
To end an intercom call, press
on the
FLASH
disconnecting the current call. Press
again to return to the first call.
SPEAKER
handset, press
on the base, or
hang up the handset.
Note:
services, pressing
the current call.
If you do not have any special phone
If a call comes in during an intercom conver-
sation, either the person at the base or the
person at the handset can answer the call.
FLASH
might disconnect
TALK
SPEAKER
on
Press
on the handset or
USING TONE SERVICES
ON A PULSE LINE
the base once to end the intercom call, then
TALK
SPEAKER
again to answer the
press
or
incoming call.
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
Note:
You can use the intercom while a call
is on hold, but not during a conversation.
15
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 16 Friday, July 21, 2000 8:01 AM
• If you receive a call during memory
entry, the phone exits the storing pro-
cess.
Transferring a Call Between the
Handset and Base
You can use the phone’s intercom feature to
transfer a call between the handset and the
base.
Follow these steps to store a number in the
handset’s memory.
1. Lift the handset.
To transfer a call from the handset to the
INTCM
base, press
. The call is placed on
MEM
2. Hold down
until Memory Store
hold, and Paging Base and Hold appear.
and a list of memory location numbers
appear.
When the person at the base answers, press
TALK
. The call is released from hold and
transferred to the base. To return to handset
01–20
VOL/
3. Press a number (
) or press
CID 8
9
or
to choose a two-digit mem-
TALK
INTCM
.
use, press
or
ory location. Precede a single digit loca-
tion number with 0 — 01, 02, 03, and so
on.
To transfer a call from the base to the hand-
set, press
INTCM/PAGE
. The call is placed on
hold, and Paging and Hold appear. When
the person with the handset answers, press
SELECT/CHAN-
4. To store a name, press
NEL
. Store Name appears.
SPEAKER
. The call is released from hold and
transferred to the handset. To return to the
If you do not want to enter a name, skip
to Step 6.
SPEAKER
INTCM/PAGE
.
base use, press
or
VOL/CID 8
9 to select the characters. Press 6 or
5. To enter a name, press
or
MEMORY DIALING
You can store up to 30 numbers in memory
(20 in the handset’s and 10 in the base’s
memory), then dial a stored number by
pressing a memory location number.
7 to move the cursor left or right.
VOL/CID 9
Repeatedly press
to view
the characters in alphabetical order.
(The display shows uppercase letters
first, then lowercase letters, numbers,
and special characters.)
You can also store a name with each number
in the handset’s memory.
Use the supplied memory directory sticker to
record your stored numbers. Peel the back-
ing from the sticker and attach it to the
base’s handset cradle.
Notes:
VOL/CID 8
• Press
to see the charac-
ters in reverse alphabetical order.
VOL/CID 8
to scroll rapidly through the charac-
9
• You can hold down
or
Storing a Number in the Handset’s
Memory
ters.
Notes:
• If you make a mistake, move the cur-
sor over the error, then enter the cor-
• The phone beeps five times and exits
the storing process if you wait more than
20 seconds between each keypress.
DEL
rect character, or press
to delete
a character. To delete all the charac-
DEL
ters, hold down
ond.
for at least 1 sec-
16
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 17 Friday, July 21, 2000 8:01 AM
SELECT/CHANNEL
6. Press
. Store Num-
Delete Memory nn — The display
ber appears.
prompts you to confirm the deletion.
VOL/CID 8
Press
to move the cursor to
7. Enter the phone number and any tone or
pause entries (see “Using Tone Services
on a Pulse Line” on Page 15 and “Enter-
ing a Pause” on Page 18).
SELECT/CHANNEL
Yes, then press
DEL
or
. The phone beeps, and Memory
nn Deleted appears.
Go Back — Returns you to the list of
memory numbers.
SELECT/CHANNEL
8. Press
. The phone
beeps and <Memory nn Stored>
appears (nn is the memory location
number you selected).
Storing a Number in
the Base’s Memory
After
2
seconds, Memory Store
Note:
The phone beeps five times and exits
appears. Repeat Steps 3–8 to store
more numbers.
the storing process if you wait more than 20
seconds between each keypress.
MEM
9. When you finish, press
.
MEM
1. Press
. The CHARGE/IN USE indi-
cator blinks.
To replace a stored number, store a new one
in its place.
2. Enter the number (up to 16 digits) and
any tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 15 and “Entering a Pause” on
Page 18).
Editing or Deleting a Number in
the Handset’s Memory
Follow these steps to edit or delete a memo-
ry number.
Notes:
1. Lift the handset.
• The phone beeps five times and exits
the storing process if you enter more
than 16 digits.
MEM
2. Hold down
until Memory Store
and a list of memory location numbers
appear.
• Each tone or pause entry uses one
digit of memory.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
MEM
3. Press
again, then enter the mem-
VOL/CID 8
9
.
pressing
or
0–9
ory location number ( ) where you
want to store the phone number. The
phone beeps once.
SELECT/CHANNEL
4. Press
appears with the three options listed
VOL/CID 8
.
A
menu
below. Press
or
9
to high-
To replace a number in the base’s memory,
simply store a new number in its place. To
light the desired option then press
SELECT/CHANNEL
to choose it.
MEM
erase a memory number, press
twice,
0–
then press the memory location number (
9
Edit Memory nn — edit the record as
described in Steps 5 through 7 of “Stor-
ing a Number in the Handset’s Memory”
on Page 16.
) you want to erase. The phone beeps once.
17
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 18 Friday, July 21, 2000 8:01 AM
To dial a number stored in the base’s memo-
Entering a Pause
SPEAKER
ry, press
. When you hear a dial
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an out-
side number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to con-
nect.
MEM
tone, press
, then press the memory lo-
cation number and the phone dials the num-
ber.
Note:
If you select an empty memory loca-
tion in the base, the phone beeps five times.
Enter the correct memory location number.
Chain-Dialing Service Numbers
PAUSE
To enter a 2-second pause, press
RDL/PAUSE
(
on the handset). P appears if
For quick recall of numbers for special ser-
vices (such as bank by phone), store each
group of numbers in its own memory loca-
tion. Dial the service’s main number first.
Then, at the appropriate place in the call,
you are storing a number into the handset’s
memory. You can add more pause entries
for a longer pause.
MEM
press
and the number for the location
Reviewing the Handset’s
Memory Numbers
where the additional information is stored.
To review your handset’s memory numbers,
Testing Stored Emergency
Numbers
MEM
press
. The list of memory location num-
bers (01–20) appears with the name stored
with each number (or <Memory nn> if you
did not store a name).
If you store an emergency service’s number
(police department, fire department, ambu-
lance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
To see the stored phone numbers, press 7.
An arrow to the right of the number means it
is longer than 13 digits. Press 7 again to
see the rest of the number. Repeatedly press
6 to return to the name display.
USING A HEADSET
MEM
To exit the memory number list, press
.
You can talk with hands-free convenience
using an optional headset that has a /32-inch
To see a stored name and phone number at
3
SELECT/CHANNEL
the same time, press
(2.5-mm) plug. Contact your local Ra-
dioShack store for a suitable headset.
when the cursor is by a memory location
DEL
number. To exit this display, hold down
until the display clears.
To connect the headset, open the rubber
cover marked
then insert the headset’s plug into the jack.
on the side of the handset,
Dialing a Memory Number
To dial a number stored in the handset’s
MEM
memory, lift the handset and press
. The
list of memory location numbers appears.
Choose a memory location (01–20) by press-
VOL/
ing a number or by repeatedly pressing
CID 8
9
TALK
or , then press .
18
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 19 Friday, July 21, 2000 8:01 AM
Notes:
If the phone’s Caller ID memory becomes
full, any new call replaces the oldest call’s
record.
• Connecting a headset disconnects the
handset’s earpiece and microphone.
Reviewing Caller ID Records
VOL/CID 8
9
•
or
on the handset also
controls the connected headset’s vol-
ume.
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
• If you place the handset on the base to
recharge it while the headset is con-
nected, be sure the handset seats prop-
erly.
To review the contents of each Caller ID
CALL ID
record, lift the handset and press
recall the number of records. Then, repeat-
VOL/CID 9
to
edly press
Caller ID records from the newest to the old-
VOL/CID 8
to scroll through the
With a headset connected, you can make or
answer calls as usual using the speaker-
phone or the keys on the handset.
est, or
records. To scroll quickly through the
VOL/CID 8
to scroll back through the
records, hold down
or
9
.
You can use a handset holder (available
from your local RadioShack store) to hang
the handset on your belt for greater conve-
nience.
When you scroll past the last record, the total
record number appears, then the first record.
When you scroll past the first record, the total
record number appears, then the last record.
When you finish using the headset, discon-
nect it from the handset and close the rubber
cover to protect the jack.
The top line of each record shows the date,
time and the number of calls from that num-
ber. The second line shows the caller’s
name, and the third line shows the caller’s
phone number.
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and sec-
ond rings of every call you receive.
To exit the Caller ID record display, press
CALL ID
.
Caller ID Messages
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (“Caller
ID Messages”).
Display
Description
New: XX
Total: XX
Shows the number of new
Caller ID records (records
you have not reviewed) and
the total number of records.
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the in-
Private
Name
The caller has blocked the
Caller ID information.
or
Private
Number
FLASH
coming call, press
. To resume the
FLASH
previous phone conversation, press
again.
19
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 20 Friday, July 21, 2000 8:01 AM
Storing a Caller ID
Record to Memory
Display
Description
Unknown
Name
The caller is not within a
Caller ID service area.
Follow these steps to store the name and
number from a Caller ID record into a memo-
ry location.
or
Unknown
Number
CALL ID
VOL/CID 8
9
1. Press
then
or
to
Incomplete Appears if there was an
Data
error during transmission of
Caller ID information. Occa-
sional errors are normal. If
the phone frequently dis-
plays Incomplete
Data, contact your local
telephone company or
RadioShack store.
recall the record you want to store.
2. If you want to add or delete the area
3
code, press . If it is a long distance call,
1
press .
MEM
3. Press
.
Select Location
appears.
01–20
) by
Adding/Deleting the Area Code
4. Choose a memory location (
pressing a number or by repeatedly
VOL/CID 8
9
, then press
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 13), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
pressing
or
SELECT/CHANNEL
.
If the selected location is empty, the phone
beeps to confirm that it stored the number,
then the Caller ID record appears.
However, you can add or delete the area
code. When the record is on the display,
If a record exists in the selected location,
Replace Memory? appears, prompting
you to confirm the replacement. Move the
3
press
to add or delete the area code.
3
Pressing again deletes or adds the area
SELECT/
code.
cursor to Yes or No, then press
CHANNEL
.
When you dial the number or store it into
memory, the phone dials or stores the num-
ber as it appears.
Deleting Caller ID Records
You can delete Caller ID records individually
or all at once.
Dialing Numbers from
a Caller ID Record
Follow these steps to delete a single Caller
ID record.
To dial a local number stored in a Caller ID
TALK
record, recall the record, then press
. If
CALL ID
VOL/CID 8
9
1. Press
then
or
to
1
it is a long distance call, press (1 appears
before the displayed number) before you
recall the record you want to delete.
TALK
press
. If you want to add or delete the
DEL
2. Press
. Delete Message? and
3
TALK
.
area code, press before you press
Yes/No appear with the cursor pointing
to Yes.
Note:
If a Caller ID record does not contain a
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
SELECT/CHANNEL
DEL
. The
3. Press
or
phone beeps once.
20
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 21 Friday, July 21, 2000 8:01 AM
Follow these steps to delete all Caller ID
records.
Feature
Description
Press
69
Return Call The service retains the
number of the party that
called you last and
CALL ID
1. Press
so the record totals
appear.
automatically dials that
number. Return call is
useful if you miss an
DEL
2. Press
. Delete All? and Yes/No
appear with the cursor pointing to No.
incoming call.
VOL/CID 8
Yes, then press
The phone beeps once and
Total:00 appears.
3. Press
to move the cursor to
66
70
Repeat Dial When you get a busy
signal or you want to
redial the last number
you called, the service
continuously redials the
number until the call
SELECT/CHANNEL
or
DEL
.
USING THE PHONE
COMPANY’S NETWORK
SERVICE
goes through.
Cancel Call Temporarily cancels
Waiting
your Call Waiting ser-
vice. This is useful
Your phone supports the advanced calling
services provided by many phone compa-
nies, such as Return Call, Repeat Dial, or
Cancel Call Waiting.
when you also use your
telephone line for inter-
net service or sending/
receiving faxes. Enter
the key sequence prior
to dialing the internet or
fax number. Call Wait-
ing is restored when
you disconnect the call.
To use these features, you must be in an
area where those services are available and
you must subscribe to those services
through your phone company. Contact your
local telephone company for more details on
how to subscribe.
Notes:
• When using certain calling features,
local, toll or long distance charges might
apply.
The phone has the following features pre-
programmed in its memory.
Important:
Some phone companies use dif-
• You might not be able to use certain call-
ing features on some long distance calls
or from certain types of business lines.
ferent key sequence to achieve the features.
Each section shows the built-in key se-
quence, so if your phone company uses dif-
ferent sequence, you need to edit the
sequence before using the service. See “Ed-
iting Service Name and Numbers” on
Page 22.
Follow these steps to access services.
1. Lift the handset.
MENU
2. Press
. Return Call, Repeat
Dial, and Cancel CW appear.
VOL/CID 8
9
1 2
3
3. Press
or
or , , or to
select the service you want to use.
TALK
4. Press
. The selected service num-
ber appears and is dialed.
21
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 22 Friday, July 21, 2000 8:01 AM
Note:
SELECT/CHANNEL
. A menu listing
Edit, Restore, and Go Back
You can display the programmed ser-
vice number of each calling feature. At step 2
above, press 7 to see the number and 6
to return the list of services.
4. Press
VOL/CID 8
9
appears. Press
or
to
highlight the desired option then press
SELECT/CHANNEL
to choose it.
Editing Service Name
and Numbers
Edit — Service name appears.
Edit the service name and press
SELECT/CHANNEL
.
Then, Service
You might need to change the number
stored in any of the three service locations,
for example, if your phone company uses dif-
ferent number sequence from the pro-
grammed one.
number appears. Edit the number and
SELECT/CHANNEL
press
.
Enter the
name and number as described in Steps
5 through 8 of “Storing a Number in the
Handset’s Memory” on Page 16.
Follow these steps to edit the key sequence.
1. Lift the handset.
Restore — the display prompts you to
confirm the restoration. If you want to
return to the preprogrammed calling fea-
VOL/CID 8
sor to Yes, then press
ture, press
to move the cur-
MENU
2. Hold down
until Select to
SELECT/
Edit and list of calling features
CHANNEL
. The phone beeps and Ser-
appears.
vice Setting Restored appears.
3. Choose a calling feature by pressing a
Go Back — returns you to the list of
service numbers.
1 3
VOL/CID 8
9
.
number ( – ) or
or
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
Suggestion
The phone does not work prop- Be sure the base's phone line cord and AC adapter are correctly and
erly.
securely connected.
Be sure the battery pack in the handset is connected and charged.
Return the handset to the base for about 5 seconds to reset the secu-
rity access-protection code.
The display flashes slowly
when the handset is faceup on
the base.
Make sure the battery pack in the handset is properly connected.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base's antenna to a fully vertical position.
Be sure the handset's battery pack is charged. (If the battery pack
power is too low, the handset cannot display Low Battery.)
22
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 23 Friday, July 21, 2000 8:01 AM
Problem
Suggestion
Low volume or unusual
sounds.
Someone has picked up another phone on the same line. Hang up the
other phone.
Dropout or mute.
Keep the handset away from computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances. Move to another location or turn off
the source of interference.
SELECT/CHANNEL
Press
to change the channel.
Hang up and redial the number.
The phone cannot be operated Lift the base's antenna to a vertical position.
at a useful distance from the
Return the handset to the base and recharge the battery pack.
base because the signal
becomes weak or noisy (hand-
set's range has decreased).
The handset battery pack does Check the charging contacts on the handset and base. If they are dirty,
not charge.
clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging, and Replacing
the Battery Pack” on Page 9).
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift the base's antenna to a vertical position.
Be sure the battery pack in the handset is connected and charged.
Move the base away from other electrical devices.
You have an incoming call, but Let the phone ring twice before you answer so the phone has time to
do not receive any Caller ID
information.
record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your Caller ID service is
active.
If you still have problems, disconnect the phone. If other phones on the same line work proper-
ly, the fault is in this phone or its installation. If you cannot find the problem, take the phone to
your local RadioShack store for assistance.
Modifying or tampering with the phone’s in-
ternal components can cause a malfunction
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environments. Handle
the phone carefully; do not drop it. Keep the
phone away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not performing as it should, take it
to your local RadioShack store for assis-
tance. If the trouble is affecting the telephone
lines, the phone company can ask you to dis-
connect your phone until you have resolved
the problem.
23
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-5520.fm Page 24 Friday, July 21, 2000 8:01 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-5520
UZZ01699ZZ
07A00
RadioShack Corporation
Fort Worth, Texas 76102
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|