SPECIFFICATION
PLDVD188
INSTRUCTION MANUAL
GENERAL SPECIFICATIONS
Power Requirement...............................14.4V DC(10.8 to 15.6 allow)
Current Consumption.................................................Less than 2.0A
Maximun Power output....................................................240WATTS
Line output....................................................RMS 35W x 4 @ 4 ohm
Dimensions(w x h x d)............................................182 x 53 x 158mm
DVD DECK SPECIFICATIONS
Format...........................................DVD-Video Disc (2 Layer, 2 side)
Compact Disc
Video System...................................................Standard NTSC/PAL
Audio System..........................................................................MP3
Loading System......................................................... Auto Loading
Mounting Angle................................................................0 to +/-30
OPEN
IR
TITLE
CHP TRK
RDM LOUD DTS
DIGITAL
CH
+
VIDEO
COMPACT
SEL
LOC
BND
MU
CLAS
POP
DIGITAL AUDIO
COMPACT
ST LOC INT RPT PRG
-
ROCK
VIDEO
DOLBY
DIGITAL VIDEO
D
I
G
I
T
A
L
DVD/SVCD/VCD/CD/MP3 PLAYER
APS
1TOP
2RPT
3INT
4RDM
5
6
CLK
DSP
MD
VIDEO SPECIFICATIONS
Video System..................................4:3 Letter Box and 4:3 Pan Scan
Video Output level.................................................1.0Vp-p 75 ohms
Horizontal Resolution................................................................500
Video Input Terminal......................................0.5 to 2.0Vp-p 75 ohms
POWER
SEL
MODE
+
VOL+
UP
F.FWD
/NEXT
ENTER
DN
F.BWD
/PREV.
VOL-
AUDIO SPECIFICATIONS
Fully Compatible To All Types
Of Discs Such As DVD, VCD,
SUPER VCD, MP3, CD.
STOP
PLAY
PAUSE
MENU
BAND
Maximum Output.......................................................2Vrms(+/-3dB)
Frequency Response....................................................20 to 20KHz
S/N Ratio(A-vtd)......................................................................85dB
Separation..............................................................................80dB
1
2
6
9
3
7
0
4
8
5
REPEAT
+10
SUBTITLE
LOC
ANGLE
MUTE
OSD
RADIO SPECIFICATIONS
FM SECTION
AUDIO
ST
TITLE/PBC
A/P
DSP
CLK
Frequency range.................................................87.5MHz - 107.9MHz
Usable sensitivity......................................................................3uV
I.F Frequency.....................................................................10.7MHz
AM SECTION
ANTI-THEFT FLIP DOWN DETACHABLE PANEL
CAR DVD VIDEO DIGITAL PLAYER
Frequency...........................................................530KHz - 1710KHz
AM/FM-STEREO DIGITAL PLL TUNING RADIO
WITH INFRARED REMOTE CONTROLLER
4 x 35W
Download from Www.Somanuals.com. All Manuals Search And Download.
29
2
CONTENTS
ABOUT FRONT PANEL AND PROTECTION CASE
WARNING................................................................................................. 1
REGION MANAGEMENT INFORMATION.....................................................1
CONTENTS...............................................................................................2
DVD FEATURES........................................................................................3
THE FRONT PANEL DIAGRAM...................................................................4
DESCRIPTION OF THE FRONT FACE AFTER TAKINGOUT THE FRONT PANEL...........................4
DESCRIPTION OF THE REAR CONNECTORS............................................5
THE REMOTE CONTROLLER DIAGRAM.....................................................6
DESCRIPTION OF LCD ON THE FRONT PANEL..........................................7
DESCRIPTION OF THE BACK OF THE FRONT PANEL.................................8
LOADING THE BATTERY IN THE REMOTE CONTROLLER...........................8
CONNECTING..........................................................................................9
GLOSSARY.............................................................................................10
CAUTION: Do not install the detachable panel before connecting the wire.
1. The unit is designed for negative terminal of the battery which is connected to the
vehicle metal. Please confirm it before installation.
2. If the car interior is extremely hot, as after being parked in the sun, do not use
the player until the car has been driven for a while to cool off the interior.
3. Press the OPEN button to flip down the front panel (see fig.1), then take away the
front panel (see fig.2) and put it in the protective case (see fig.3) safe keeping.
SAME FUNCTTION BBUUTTONSS IN DIISC ORR RRADIO MMODE.11
4. Install the front panel back into its bracket and then push it back to the position for
playing (see fig.4).
RADIO OPERATION......................................................................12
FRONT PANEL
FRONT PANEL
DISC BASIC OOPERRAATION
TO TURN ON TO PLAY.............................................................................13
TO PAUSE THE PLAYBACK......................................................................14
TO STOP THE PLAYBACK........................................................................14
TO END PLAYING....................................................................................15
DISC ADVVANCEEDD OPERAATION
TO SELECT PLAYING CONTENTS WITH THE MENU.................................16
FAST FORWARD OR REVERSE PLAYING.................................................16
TO SELECT NEXT OR LAST CHAPTER/TRACK TO PLAY............................17
TO REPEAT PLAYING..............................................................................17
TO CHANGE THE LANGUAGE OF THE CAPTION......................................18
TO CHECK TITLE, CHAPTER SEQUENCE NUMBER AND PLAYING TIME...18
USE OF PAD NUMBERS...........................................................................19
VIEW IN DIFFERENT ANGLE....................................................................19
TO SELECT THE FIRST TRACK/CHAPTER TO PLAY..................................20
TO SCAN DISC........................................................................................20
TO PLAY DISC IN RANDOM .....................................................................20
CHANGING LANGUAGE TYPE.................................................................20
RESET DISTORTED PROGRAM...............................................................21
SETTING UP SYSTEM.............................................................................21
OPEN BUTTON
( FIG.1)
( FIG.2)
PROTECTIVE CASE
INSTALLATION........................................................................................25
CARE AND MAINTENANCE......................................................................27
ABOUT FRONT PANEL AND PROTECTION CASE......................................29
TROUBLE SHOOTING..............................................................................30
SPECIFICATION............................................................................COVER 4
FRONT PANEL
( FIG.3)
FRONT PANEL
( FIG.4)
Download from Www.Somanuals.com. All Manuals Search And Download.
28
3
CLEANING DISCS
DVD FEATURES
Before playing, clean the disc with a clean, lint-free.
Flip the disc in the direction of the arrow.
MAIN FUNCTIONS
* Fully compatibility/ Its fully compatible to all types of discs
such as DVD, SVCD, VCD, CD, Mp3.
NOTE:
. Do not use so solvents such as benzine, thinners. Commercially available
cleaners or anti static spray damage the unit.
* Picture with high fidelity resolution/ Horizontal resolution
as high as 500dpi. It can make full use of the advantages
of large screen TV based on the fidelity of normal TV.
Insert a disc with the label surface down. Doing so may damage the unit.
Label
surface up
OTHER FUNCTIONS
NOTE:
. Do not try to insert another disc when one has been already inserted.
Doing so may damage the unit.
.Handle the disc by its edge. And to keep the disc clean, do not touch
the surface.
* Many angles of enjoyment/Users can enjoy the picture from
different angles selected such as zoom in, side view,
panorama etc.
* Many types of picture ratio modes/ These modes enable
the DVD player to suit different TV screen.
.Do not stick paper or tape on the disc.
.Do not expose the disc to direct sunlight or heat sources such as hot air
ducts. Or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
4
THE FRONT PANEL DIAGRAM
CARE AND MAINTENANCE
4
9
2
1
3
12
DVD CARE
* Always handle the disc by the edges. Never touch the surface. To
remove fingerprints and dust, use a soft cloth and wipe in a straight
line from the center of the disc to the outside edge.(See page 28)
* Take care of IR Remote Control. Keep the remote with your DVD
cases, where it is unlikely to be lost or damaged.
* Keep liquids away from the DVD player, including beverages and
cleaning liquids. Spilling any liquid on the player can damage the
electronics, resulting in an electrical shock or fire.
OPEN
IR
TITLE
CHP TRK
RDM LOUD DTS
DIGITAL
CH
+
VIDEO
COMPACT
SEL
LOC
BND
MU
CLAS
POP
DIGITAL AUDIO
COMPACT
ST LOC INT RPT PRG
-
VIDEO
ROCK
DOLBY
DIGITAL VIDEO
D
I
G
I
T
A
L
DVD/SVCD/VCD/CD/MP3 PLAYER
APS
1TOP
2RPT
3INT
4RDM
5
6
CLK
DSP
MD
* If the unit or remote control should become wet, turn off all power
and let an authorized dealer clean or service the equipment.
CAUTION:
DO NOT ATTEMPT TO OPEN OR SERVICE THE UNIT OR REMOTE
CONTROL. THE INTERNAL PARTS ARE NOT USER SERVICEABLE.
* Do not use any liquid or aerosol cleaners, anti-static spray, or
thinner to clean the disc surface.
10 11
6
5
14
15
8
13
7
9. LOCAL/DISTANCE BUTTON
1. OPEN BUTTON
2. LCD SCREEN
10. APS BUTTON
* Do not allow coins, cleaning cloths, papers and other objects to be
pushed into the DVD slot, these objects could connect with a voltage
point inside the unit and cause an electrical shock, or may short out
pacts causing unit failure or fire.
11. CLOCK BUTTON
3. IR REMOTE SENSOR
4. BAND BUTTON
12. MUTE/LCD COLOUR BUTTON
13. PRESET STATION AND TOP/RPT
/INT/RDM BUTTONS
5. UP(^)/DN(V) BUTTONS
6. PLAY/PAUSE BUTTON
7. MODE BUTTON
TEMPERATURE AND MOISTURE
when the inside of the vehicle is very cold and the player is used
immediately, moisture may form on the disc or the optical parts and
proper playback may not be possible. If moisture forms on the disc,
wipe it off with a soft cloth. If moisture forms on the optical parts of
the player, allow the player to sit for about one hour with power on.
The condensation will disappear naturally allowing for normal operation.
Please consult your nearest dealer for recommendations and service.
14. POWER BUTTON
15. SOUND MODE AND LEVEL BUTTONS
8. DISPLAY/SUBWOOFER BUTTON
DESCRIPTION OF THE FRONT FACE AFTER TAKING OUT THE FRONT PANEL
OPERATION PRECAUTIONS
* Do not subject the unit to direct sunlight or in extremely hot
environment (e.g closed windows on a hot summer day, direct,
direct path or heater vent, etc.).
RESET
* Avoid using the unit under the following conditions:
- After external parking on an extremely hot or cold day.
- Near strong magnetic fields.
- In an environment with excessive humidity, dust, or vibration(e.g
off-road travel, etc.)
* Do not directly touch the disc surface. Never stick labels on the
surface of the disc or mark the surface with a pen.
* Always place a DVD disc back into its case after use.
1
2
1.LED INDICATOR: Flashing when detachable panel is removed.
2.RESET BUTTON: Press it to rehabilitate the distorted program
to zero.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
5
INSTALLLATION
DESCRIPPTION OF THHE REAR COONNNECTORS
1
Firstly install the left side, then push
the right side to make it combine
with the unit chassis.
4
2
3
1,2. VIDEO OUTPUT (2 RCA jacks)
Use an video cable to connect the video output signal to the external
video monitors.
3. OPTICAL DIGITAL AUDIO OUTPUT
Use an optical audio cable to connect the digital audio output signal
to external audio amplifier system.
4. WIRING CONNECTING SOCKET
Download from Www.Somanuals.com. All Manuals Search And Download.
25
6
THE REMOTE CONTROLLER DIAGRAM
INSTALLATION
2
1
3
POWER
MODE
SEL
4
5
25
24
23
DASH BOARD
1. MODE BUTTON
+
VOL+
UP
ENTER
DN
F.FWD
/NEXT
2. SEL BUTTON
6
METAL MOUNTING STRAP
F.BWD
/PREV.
VOL-
7
HEX NUT
3. POWER BUTTON
22
21
SPRING WASHER
8
STOP
PLAY
PAUSE
MENU
BAND
CONSOLE
PLAIN WASHER
PLAIN WASHER
4. JOG UP/SEEK UP BUTTON
5. F.FWD/NEXT BUTTON
6. JOG RIGHT BUTTON
7. F.BWD/PREV. BUTTON
8. JOG DN/SEEK DN BUTTON
9. MENU/BAND BUTTON
9
SLIDE BRACKET HOUSING
TAPPING SCREW
1
2
6
9
3
7
4
8
10
11
5
20
HEX BOLT
REPEAT
0
+10
19
18
17
16
12
13
SUBTITLE
LOC
MUTE
ANGLE
OSD
AUDIO
ST
TITLE/PBC
A/P
DSP
CLK
14
15
18. OSD BUTTON
10. PLAY/PAUSE BUTTON
KEY PLATE
19. SUBTITLE AND LO/DX BUTTON
20. REPEAT BUTTON
11. NUMBER/PRESET
MEMORY BUTTONS
12. ANGLE BUTTON
PLASTIC TRIM OUT
KEY PLATE
21. STOP BUTTON
13. MUTE/LCD COLOUR BUTTON
14. CLOCK BUTTON
22. VOLUME - BUTTON
23. JOG LEFT BUTTON
24. VOLUME + BUTTON
25. ENTER BUTTON
15. DISPLAY/SUBWOOFER
BUTTON
16. TITLE/PBC AND A/P BUTTON
17. AUDIO AND ST/MO BUTTON
Download from Www.Somanuals.com. All Manuals Search And Download.
24
7
DESCRIPTTION OF LCCDD ON THE FROONT PANEL
12
11
13
10
5
6
7
4
9
DYNAMIC
FULL
6/8
4/8
2/8
OFF
TITLE
CHP TRK
RDM LOUD DTS
DIGITAL
CH
CLAS
POP
ST
INT RPT
LOC
PRG
ROCK VIDEO
OFF
ON
PRO LOGIC
2
1
14
15
16
17
3
8
AUTO
1. DVD/VCD/CD/MP3 indicators
2. Operating statusindicators (play orpause)
LPCM 48K
LPCM 96K
LPCM OUTPUT
3. Repeat playbackindicators (single orall for DVDdisc, single forVCD/CD disc,
single, folder andall for MP3disc)
4. Title number indicator
5. Chapter numberindicator
3). The setup items of each setup item in the PREFERENCES setup
menu show like the following:
6. Disc playingtime indicator for DVD/VCD, track timeindicator for CD/MP3.
7. Dolby digitalindicator
MULTI
NTSC
PAL
TV TYPE
8. Viewing in different angle indicator
9. Disc rotation indicator
10. RANDOM indicator
DEFAULTS
RESET
11. LOUDNESS indicator
12. DTS digitaloutput indicator
13. SPECTRUM indicator
4. Press JOG button to select the setup item and then press ENTER
button to make it effective.
14. CLASSIC, POPand ROCK equalizer curves indicators
15. STEREO indicator
16. LOCAL stationindicator
17. SCAN discindicator
Download from Www.Somanuals.com. All Manuals Search And Download.
23
8
1). The setup items of each setup item in the GENERAL setup menu
show like the following:
DESCRIPTIION OFF THE BBAACK OF TTHE FRRONT PANEL
NORMAL/PS
NORMAL/LB
WIDE
TV DISPLAY
AUTO
HI-RES
N-FLICKER
PIC MODE
EJ
ON
OFF
ANGLE MARK
OSD LANG
ENGLISH
CHINESE
1
EJECT BUTTON: Press it to eject the disc from compartment.
ON
OFF
CAPTIONS
ON
OFF
SCR SAVER
LOADING THHE BATTTTERY INN THE REEMOTE CCONTROLLER
REMOTE CONTROL BASICS BATTERY REPLACEMENT
1.Remove the battery holder as the direction indicated by the arrow.
2.Replace the battery Set a new battery property with (+)side up as
illustrated.
2). The setup items of each setup item in the AUDIO setup menu
show like the following:
ANALOG
SPDIF/RAW
SPDIF/PCM
AUDIO OUT
3.Insert the battery holder. Push in the holder to the original position.
NOTE ON BATTERIES
1.Old batteries must immediately be removed and disposed.
2.Improper use of batteries may cause overheating, explosion or ignition.
Resulting in jury or fire .
LINE OUT
F
R REMODE
OP MODE
3.Battery leakage may cause damage to the unit.
4.Do not disassemble or short the batteries.
5.Do not throw the batteries into the fire.
STEREO
DUAL MONO
L-MONO
R-MONO
MIX-MONO
6.To avoid the risk of accident, keep the batteries out of reach of children.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
9
CONNECTING
AUDIO
SETUP
2).
POWER AND SPEAKERS OUTPUT
AUDIO OUT
OP MODE
DUAL MONO
DYNAMIC
ANTENNA PLUG
PRO LOGIC
LPCM OUTPUT
10A
WOOFER LINE OUT
YELLOW
YELLOW
MEMORY B+
FUSE
MAIN PAGE
??????(display the selected item)
BLACK(GND)
1A
RED
RCA LINE OUT
RED R
IGNITION SWITCH
FUSE
WHITE L
1A
BLUE AUTO ANT
3).
FUSE
PREFERENCES PAGE
FRONT
+
+
+
GRAY
WHITE
FRONT
TV TYPE
DEFAULTS
WHITE / BLACK
GREEN
GRAY / BLACK
VIOLET
RIGHT
SP
LEFT
SP
+
REAR
REAR
VIOLET / BLACK
GREEN / BLACK
MAIN PAGE
??????(display the selected item)
NOTE:
In spite of having any kinds of speaker system, must use 4 ohms
impedance of speaker to reduce the distortion during high volume
level.
3. In one of the above setup menu, press JOG up or down button to
select setup item, so the TV screen will show the setup items of
the selected setup item on the right side of the selected setup
item(select MAIN PAGE item and then press ENTER button to
return back to SETUP MENU). These setup items menu of each
one of the GENERAL, AUDIO SETUP and PREFERENCES setup items
like followings:
Download from Www.Somanuals.com. All Manuals Search And Download.
10
21
GLOSSARY
RESET DISTORTED PROGRAM
When the program of the DVD player is distorted or the disc in the slot
can not be ejected, press OPEN button on the front panel to flip down
the front panel from the DVD player, then take away the front panel
from the DVD player and then press the RESET button on the front
facet of the unit chassis to rehabilitate the distorted program to zero;
finally install the front panel back to the previous position in the DVD
player.
Title: The longest sections of a picture or a music piece or a
movie etc on a DVD. Each title is assigned a title number
enabling you to locate the title you want.
Track: The sections of a picture or a music piece on a VCD or
CD. Each track is assigned a track number enabling you
to locate the track you want.
SETTING UP SYSTEM
1. Press MENU button on the IR remote controller to display the
following settings menu on the TV screen:
Chapter: A complete section of a picture or a music piece on a
DVD that are smaller than a title. A title is composed of
several chapters. Each chapter is assigned a chapter
number.
SETUP MENU....MAIN PAGE
GENERAL SETUP
AUDIO SETUP
PREFERENCES
Caption: The language displayed at the bottom of the TV screen,
normally the translation or the dialogue, which are also
recorded on the disc.
EXIT SETUP
??????(display the selected item)
Angle: Some DVD disc are recorded from different angles so
that users can view the same scene from different angles.
2. Press JOG up or down button to select the SETUP item in the
settings menu, then the DVD player will display the following
settings menus on the TV screen (select EXIT SETUP item and then
press ENTER button to exit setting menu to resume normal playback)
1).
GENERAL
PAGE
TV DISPLAY
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
NORMAL/PS
NORMAL/LB
WIDE
SCR SAVER
MAIN PAGE
??????(display the selected item)
Download from Www.Somanuals.com. All Manuals Search And Download.
20
11
TO SELECT THE FIRST TRACK/CHAPTER TO PLAY
SAME FFUNCTTION BUTTONNS IN DDISC OORR RADIO MODE
1. In the state of VCD/CD/MP3 disc playing, press the 1TOP button
on the front panel to select the first track/chapter to play.(depend
on the disc used for VCD)
1. POWER BUTTON
Press the POWER button on the front panel or the remote controller
to turn on the unit.
2. MODE BUTTON
2. In the state of DVD disc playing, the 1TOP button is not available.
Press the MODE button on the front panel or the remote controller
to select DISC or RADIO mode.
3. AUDIO MODE AND LEVEL BUTTONS
TO SCAN DISC
Press the SEL button on the front panel or the remote controller
to select the audio mode such as VOL, BASS, TREBLE, BALANCE
and FADER, then press the + or - button on the front panel or the
remote controller to adjust the level of them.
1. In the state of VCD/CD disc playing, press the 3INT button
on the front panel to play the previous 10 seconds part of each
track/chapter on disc.(depend on the disc used for VCD)
4. MUTE/LCD COLOUR (EFFECT ONLY FOR MULTI-COLOUR LCD, NO
EFFECT FOR BLACK MASK LCD) BUTTON
2. In the state of DVD/MP3 disc playing, the 3INT button is not
available.
Press the MUTE button on the front panel or the remote controller
to eliminate the sound immediately and the audio mute indicator on
the LCD will be flashed, press it again to resume the normal playback.
Press it hold for more than 2 seconds to turn on or off the LCD FLASH,
and the LCD will show FLASH ON or FLASH OFF. When in FLASH ON
mode, the LCD will change the LCD light colour alternatively. When
finding your desired LCD flash colour, press it hold for more than 2
seconds again to select the LCD light colour and stop flashing.
5. CLOCK DISPLAY AND ADJUSTMENT BUTTONS
Press the CLK button on the front panel or the remote controller
to display time on LCD. Press the CLK button hold for about 2 seconds
to flash HOUR, then press the + or - button on the front panel or the
remote controller to adjust HOUR, then press the SEL button to flash
MINUTE, then press the + or - button to adjust MINUTE.
6. DSP/SUBWOOFER BUTTON
TO PLAY DISC IN RANDOM
1. In the state of VCD/CD/MP3 disc playing, press the 4RDM button
on the front panel to play in random or select DISC REP.(depend on
the disc used for VCD)
2. In the state of DVD disc playing, the 4RDM button is not available.
CHANGING LANGUAGE TYPE
Press the DSP button on the front panel or the remote controller
to select the preset music equalizer curves: FLAT, POP, CLASSIC
and ROCK. The sound effect will be changed.
1. In the state of DVD disc playing, press the AUDIO button repeatedly
on the IR remote controller to select the desired language type.
(depend on the disc used)
Press it for more than 2 seconds to turn on(default) or off the sub-
woofer.
7. OPEN BUTTON
Press the OPEN button on the front panel to flip down the front
panel from the unit, then you can insert the disc into the disc
compartment or press the EJECT button on the back of the front
panel to eject the disc or take away the front panel.
8. IR REMOTE SENSOR
2. In the state of MP3 disc playing, the AUDIO button on the IR remote
controller is not available.
3. In the state of VCD/CD disc playing, press the AUDIO button
repeatedly to select STEREO, MONO LEFT and MONO RIGHT sound
mode, no language function.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
19
RADIO OPERATION
USE OF PAD NUMBERS
1. PRESET STATION [ 1-6 ] BUTTONS
A]. To memorize the current frequency, press any one of the six preset
buttons(1-6) on the front panel or on the remote controller hold for more
than 2 seconds.
1. In the state of VCD disc playing, press PBC button on the IR
remote controller to turn PBC function ON/OFF:
1).When it is in the state of PBC ON and display the title menu on the TV
screen if the disc include TITLE MENU, press one of NUMBER buttons
to select the track/chapter to playback; During playing, the NUMBER
buttons are not available.
B]. To recall the preset memory, press one of the preset buttons [1-6].
2. AS/PS BUTTON
When shortly pressing the APS button on the front panel or the A/P button on
2).When it is in the state of PBC OFF, press one of the NUMBER buttons
to select the chapter/track to playback.
the remote controller, the radio searches for each preset station. When the field
strength level is more than the threshold level of stop level, the radio is holding
at that preset number for few seconds with releasing mute, and then searches
again. In FM band, FM 1,FM 2 and FM 3 is checked one at a time.
When long pressing the APS or A/P button (more than 1 second), the radio
searches from the current frequency and checks the signal strength level until
1 cycle search is finished. And then 6 strongest stations are preset to the
corresponding preset number. The AS operation is implemented in the each
band of selected band. When the AS operation is finished, the radio executes
the preset scan.
2. In the state of DVD disc playing, press TITLE button to display the
title menu; then press the NUMBER button to select the chapter/
track to playback.
3. In the state of CD/MP3 disc playing, press the NUMBER button to
select the chapter/track to playback.
*
*
+10 BUTTON: Press it once to display 1-, then press one of 1-9
NUMBER buttons to select one of the 11th-19th tracks. Press it
twice to display 2-, then press one of 1-9 NUMBER buttons to
select one of the 21th-29th tracks. Press one of 1-9 NUMBER
button and then press +10 button to display 1- again(depend on the
disc used).
The 1-6 digital buttons on the front panel have not the function of
selecting track/chapter to playback, but the 1-4 digital buttons on
the front panel have the function of TOP, RPT, INT and RDM.
3. LOC BUTTON(effect only for FM)
If you find that the signal is weak and the listening effect is bad when tuning for
the distance station, check whether the word LOC is displayed on LCD. If the
word LOC is displayed on LCD, press the LOC button on the front panel or the
remote controller to turn off LOC function, then tune for distance radio station
again.
If you find that the signal is so strong that the interfere is stronger when tuning
for the local station, check whether the word LOC is displayed on LCD. If the word
LOC is displayed on LCD, press the LOC button to turn on LOC function, then
tune for local radio station again.
4. BAND and PAL/NTSC BUTTON
VIEW IN DIFFERENT ANGLE
In RADIO mode, press it repeatedly on the remote controller or the BND button
on the front controller to select your desired radio band and word which band
is selected will be displayed on LCD.
1. In the state of VCD/MP3/CD disc playing, the ANGLE button on
the IR remote controller is not available.
In DISC mode, press it repeatedly to select PAL or NTSC mode.
2. In the state of DVD disc playing, press TITLE button on the IR remote
controller to display TITLE MENU on TV screen, then select ANGLE
FUNCTION item and then press ENTER button on the IR remote
controller to turn into ANGLE function playing mode, then press the
ANGLE button repeatedly on the IR remote controller to view in
different angle.(depend on the disc used)
5. TUNE/SEEK UP/DOWN BUTTONS
Press UP or DN button on the remote controller or ^ or v button on the front
panel to manually tune up or down for your desired station. Press them hold for
more than 2 seconds to automatically tune up or down for the stronger station.
6. STEREO/MONO BUTTON
Press the ST button on the remote controller to select STEREO or MONO sound
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
13
IN THE STATE OF MP3 DISC PLAYING
DISC BASIC OPERATION
Press the REPEAT button on the IR remote controller or the 2RPT button on the
front panel to select REPEAT ONE, FOLDER REPEAT or DISC REPEAT. Press the
PLAY/PAUSE button to resume the normal playback.(The defaulted repeat mode
is DISC REPEAT).
TO TURN ON TO PLAY
1. Connect the DVD player into the video monitor and adjust the video
monitor to make it to be in good state of COLOUR, BRIGHTNESS
and so on.
IN THE STATE OF CD DISC PLAYING
Press the REPEAT button on the IR remote controller or the 2RPT button on
the front panel to select REPEAT ONE, DISC REPEAT(defaulted repeat mode).
2. Press POWER button on the remote controller or the front panel
of the DVD player to turn on the DVD player, then the DVD VIDEO
will displayed on TV screen(if it is in disc mode).
TO CHANGE THE LANGUAGE OF THE CAPTION
In the state of DVD disc playing, press SUBTITLE button repeatedly to select
the language of the caption or turn off the caption.(depend on the disc used.)
3. Press OPEN button on the front panel of the DVD player to flip
down the front panel, then insert the disc in the slot with the label
side upward. When the disc is inserted halfway, it is automatically
pulled into the unit. At the moment, the TV screen will show DISC
LOADING, then PLAY in the upper left corner and the DVD LCD will
show disc rotation indicator, DVD/CD/VCD/MP3 (depend on the
disc species) indicator, playing indicator(depend on disc species),
title number indicator(depend on disc species), chapter number
indicator(depend on disc species) and disc playing time indicator.
Some discs may automatically start playback from the first chapter
/track. Some discs will automatically start playback by displaying
the disc title menu on TV screen.
In the state of VCD/CD/MP3 disc playing, the button is not available.
TO CHECK TITLE, CHAPTER SEQUENCE NUMBER OR PLAYING TIME
1. In the state of DVD disc playing, press the OSD button repeatedly on the
remote controller to display the title, chapter sequence number or different
species of time about current playing disc, such as TITLE REMAIN time,
CHAPTER ELAPSED time and CHAPTER REMAIN time.
2. In the state of CD disc playing, press the OSD button repeatedly on the
remote controller to display the different species of time about current
playing disc, such as SINGLE ELAPSED time, SINGLE REMAIN time, TOTAL
ELAPSED time, TOTAL REMAIN time, then checking time OFF.
4. When displaying the DVD title menu on TV screen, press PLAY/
PAUSE button on IR remote controller or the front panel of the DVD
player to play the defaulted first track/chapter; or press JOG
buttons to select track/chapter in the DVD title menu and then
press ENTER button on the IR remote controller or PLAY/PAUSE
button on the IR remote controller or on the front panel of the DVD
player to play the selected track/chapter.
3. In the state of MP3 disc playing, press the OSD button repeatedly on the
remote controller to display the different species of time about current
playing disc, such as SINGLE ELAPSED time, SINGLE REMAIN time.
4. In the state of VCD disc playing:
*
When playback a double-sided DVD video disc, insert the disc with
top side up. Play it back in its entirety, then take out the disc and
turn it over to play the second side. (The top and back side of a DVD
video disc are marked differently on different discs)
1).When in the state of PBC ON, press the OSD button repeatedly on the remote
controller to display the different species of time about current playing disc,
such as SINGLE ELAPSED time, SINGLE REMAIN time, and then OFF.
2).When in the state of PBC OFF, press the OSD button repeatedly to display the
different species of time about current playing disc, such as SINGLE ELAPSED
time, SINGLE REMAIN time, TOTAL ELAPSED time, TOTAL REMAIN time,
then checking time OFF.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
17
TO SELECT NEXT OR LAST CHAPTER/TRACK TO PLAY
TO PAUSE THE PLAYBACK
1. Press the F.FWD/NEXT button on the IR remote controller or the
^ button on the front panel during playback to select the next
chapter/track to playback.
In the state of DVD/VCD/CD/MP3 disc playing, press the PLAY
/PAUSE button on IR remote controller or the front panel of DVD
player to pause the playback, press the PLAY/PAUSE button again
to resume normal playback.
NOTE: PRESS THE F.FWD/NEXT OR ^BUTTON MULTIPLE TIMES TO
ADVANCE MULTIPLE CHAPTERS FORWARD.
2. Press the F.BWD/PREV. button on the IR remote controller or the
v button on the front panel during playback to select the last
chapter/track to playback.
TO STOP THE PLAYBACK
NOTE: PRESS THE F.BWD/PREV. OR V BUTTON MULTIPLE TIMES
TO ADVANCE MULTIPLE CHAPTERS BACKWARD.
*
*
The sound is muted during chapter/track forward or backward.
While in chapter/track forward or backward the display status
screen is activated along the top of the screen.
In the state of DVD disc playing, press the STOP button once on IR
remote controller to stop the playback, then press the PLAY/PAUSE
button to resume the normal playback; press the STOP button twice to
full stop the playback, then press the PLAY/PAUSE button to start
playback from the first chapter/track of the disc.
*
For VCD disc, when PBC ON, the PREV. button is not available.
TO REPEAT PLAYING
In the state of MP3/CD disc playing, press the STOP button on IR
remote controller to stop the playback. Then press the PLAY/PAUSE
button to resume the normal playback.
IN THE STATE OF DVD DISC PLAYING
In the state of VCD disc playing, press PBC button on the IR remote
controller to turn PBC function ON/OFF:
Press the REPEAT button on the IR remote controller or the 2RPT
button on the front panel to select CHAPTER REPEAT, TITLE REPEAT
or REPEAT OFF.
1. When starting to turn on PBC function, it will play from the beginning
of disc(it will display title menu on TV screen if the disc include title
menu, then press NUMBER or NEXT button to select chapter/track
to play). During playback, the STOP button is not available. (For some
discs, when it is in PBC on, press STOP button to return back to title
menu during playback.)
IN THE STATE OF VCD DISC PLAYING
Press PBC button on the IR remote controller to turn PBC function
ON/OFF(the defaulted mode is PBC OFF):
1. When it is in the state of PBC ON, during playing, the REPEAT
button on the IR remote controller or 2RPT button on the front
panel are not available.
2. When it is in the state of PBC OFF, during playing, press the
REPEAT button on the IR remote controller or 2RPT button on the
front panel to select REPEAT ONE or REPEAT OFF.
2. When starting to turn off PBC function, it will also play from the
beginning of disc(it will not display title menu on TV screen even if
the disc include title menu). During playback, press the STOP button
to stop playback, and then press the PLAY/PAUSE button to play
from the beginning of disc again.
TO MUTE
Download from Www.Somanuals.com. All Manuals Search And Download.
16
15
DISC ADDVANCEED OPERRATION
TO END PLAYING
TO SELECT PLAYING CONTENTS WITH THE MENU
If the disc includes the title menu:
1. Press OPEN button on the front panel of the DVD player to flip down
the front panel, then press EJECT button on the back of the front
panel of DVD player to eject the disc from the slot and take away the
disc.
In the state of DVD disc playing
1. press TITLE button on the IR remote
controller to display title menu on the TV screen.
2. Press JOG button on the IR remote controller to select your desired
chapter/track or other icon; or press number button to select your
desired chapter/track to playback.
3. Press ENTER button on the IR remote controller to play the selected
chapter/track; or to display the subtitle menu on the TV screen, then
press JOG button to select your desired chapter/track or other icon,
then press ENTER button to play the selected chapter/track.
2. Press the POWER button on the IR remote controller or the front
panel of the DVD player to turn off the DVD player.
NOTE:
In the state of CD disc playing
The TITLE, JOG and ENTER buttons are disabled.
In the state of DVD/VCD/CD/MP3 disc playing, if the power
button or the ignition is shut off and then turn on the power or
the ignition, the DVD player will resume play at the exact spot
where playback was interrupted.
In the state of VCD disc playing, press PBC button to turn PBC on or off.
1. When starting to turn on PBC function, it will play from the beginning of disc
till it display title menu on TV screen if the disc include title menu.
For some VCD discs, when it is in PBC on, press STOP button to return back
to title menu during playback. Then press the NEXT or NUMBER button to
select track/chapter to playback.
2. When starting to turn off PBC function, it will also play from the beginning
of disc, but it can not show the title menu.
In the state of MP3 disc playing:
1. After inserting the MP3 disc into the disc slot and then the title menu be
showed on TV screen; then press JOG button to select your desired FOLDER,
then press ENTER button to display the subtitle menu on the TV screen, then
press JOG button to select your desired track, then press ENTER button to
play the selected track to playback.
NOTE:
1. If the DVD player can not convey the disc to the reading position
after inserting disc into disc compartment, press EJECT button
hold for more than about 3 seconds to make the DVD player convey
the disc to the reading position.
2. During playing, the TITLE, JOG and ENTER buttons are not available, you can
press the digital buttons to select the track to playback.
FAST FORWARD OR REVERSE PLAYING
2. If the DVD player can not eject out the disc from the disc compart-
ment after pressing EJECT button shortly, press EJECT button
hold for more than about 3 seconds to make the DVD player eject
out the disc from the disc compartment.
Press the F.FWE/NEXT or F.BWD/PREV. button continuously on
the IR remote controller or the ^ or v button on the front panel hold
during normal playback to fast play forwards or backwards.
*
While in rapid preview or rapid review the display status screen in
activated along the top of the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
|