OWNER’S MANUAL
PLCD32
PLL SYNTHESIZER STEREO RADIO WITH
COMPACT DISC PLAYER DIGITAL
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Dashboard
2. Nut (5mm)
1
7
6
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
4
5
2
3
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
(Fig. 2)
7. Plain washer
Removing the unit
1. Frame
1
2. Insert fingers into the groove in the front
of frame and pull out to remove the
frame. (When reattaching the frame,
point the side with a groove downwards
and attach it.)
2
3
3. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
1
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw holes
of the bracket and the screw holes of
the main unit become aligned (are fitted),
and tighten the screws at 2 places on
each side.
2
4
Use either truss screws (5 x 5mm) or
flush surface screws (4 x 5mm),
depending on the shape of the screw
holes in the bracket.
5
3
2. Screw
2
5
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method B
installation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO REMOVE AND INSTALL THE FRONT PANEL
1. Press the release button and pull-off the front panel.
Keep front panel into the case.
2. To install the front panel, insert the panel into the housing and make sure the panel
is properly installed, otherwise, abnormalities occurs on the display or some keys
will not function properly.
REMOVING THE FRONT PANEL
Front Panel
Release Button
INSTALLING THE FRONT PANEL
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING CONNECTION
MAIN UNIT
ANTENNA CONNECTOR
IGNITION RED
SWITCH (B+)
(GREY)
Rch RED
RCA CABLE
YELLOW
MEMORY
BACK-UP
Lch WHITE
BLACK
GROUND (B–)
BLUE
POWER
ANTENNA
2-SPEAKERS SYSTEM
WHITE
4-SPEAKERS SYSTEM
4-SPEAKERS SYSTEM
2-SPEAKERS SYSTEM
GREY
WHITE
FRONT
GREY
FRONT
Lch SPK.
Rch SPK.
WHITE/BLACK
GREY/BLACK
Lch
Rch
SPK.
SPK.
GREEN
REAR
VIOLET
REAR
Lch SPK.
Rch SPK.
GREEN/BLACK
VIOLET/BLACK
VIOLET/BLACK
GREEN/BLACK
Note:
1. For 2-speakers system, green, violet, white/black and grey/black wire leads are
unconnected and isolated.
2. For 2-speakers system, keep the fader indicator at center position to maintain the
existing volume level.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
7 17 2
1
3
5
8
12
10 11
4
16 18 13 20
21
22 14 23
19 15 6
9
24
25
GENERAL OPERATION
• ON/OFF
Switch on the unit by pressing any button [except button (4) and RELEASE button
(7)]. When system is on, press button (9) to turn off the unit.
• FACEPLATE RELEASE
Press RELEASE button (7) to detach the removable faceplate.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• SOUND ADJUSTMENT
Press SEL button (10) to select the desired adjustment mode.
The adjustment mode will change in the following order:
Volume
Bass
Treble
Balance
Fader
By pressing VOL button (11) or VOL button (12), it is possible to adjust the
desired sound quality.
• LOUDNESS
Press BND/LOU button (13) for several seconds to reinforce the bass output and
display will show “LOUD”. Press it for several seconds again to release this
function.
• SET THE CLOCK
Holding down the DSP button (15) until the clock is shown on the LCD display and
flashed. Then press the TUNE/SEEK/TRACK
button (17) to change hours or
button (16) to change minutes.
TUNE/SEEK/TRACK
• SELECT MODE
Press MOD button (6) to choose desired listening mode.
(e.g. radio mode to CD mode)
• MUTE
Press MUT button (3) to silence the receiver. Press it again to resume listening.
• LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (8).
• EQUALIZATION
Press EQ button (19) to turn on equalization function and to select desired audio
mode. There are five kinds of mode as below:
FLAT
CLASSICS
POP M
ROCK M
DSP OFF
• FLASHING LED
If the front panel does not install in the unit, the LED (24) will be flashing.
• RESET
RESET button (25) must be activated with either a ball point pen or thin metal
object. RESET button (25) is to be activated for the following reasons:
- Initial installation of the unit when all wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: If press RESET button (25), the unit can’t work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RADIO OPERATION
• BAND SELECTION
At tuner mode, press BND/LOU button (13) shortly to select the desired band.
The reception band will change in the following order:
FM1
FM2
FM3
AM
• STATION SELECTION
Press TUNE/SEEK/TRACK
button (16) or TUNE/SEEK/TRACK
button
(17) shortly to activate automatic seek function. Press for several seconds until
“MANUAL” appeared on the display, the manual tuning mode is selected. If both
buttons have not pressed for several seconds, they will retune to seek tuning mode
and “AUTO” appeared on the display.
• LOCAL/DISTANCE
Press LOC button (2) to select between local and distant stations.
Local setting for reception of strong station, and a distant setting for reception of
weaker stations. This function is effect during AUTO SEEK operation.
• AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS button (18) for several seconds, the radio searches from the current
frequency and checks the signal strength until one cycle search is finished.
And then 6 strongest stations are stored into the corresponding preset number
button.
- Program Scanning
Press AMS button (18) shortly to scan preset station. When the field strength
level is more than the threshold level of stop level, the radio is holding at that
preset number for several seconds with releasing mute, then searches again.
• STATION STORING
Press any one of the preset buttons (14) (M1 to M6) to select a station which had
been stored in the memory. Press this button for several seconds, current station
is stored into the number button.
• MONO/STEREO
Press MON button (1) to select mono or stereo mode. You can sometimes improve
reception of distant stations by selection mono operation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CD OPERATION
• SELECT TRACKS
Press TUNE/SEEK/TRACK
button (16) or TUNE/SEEK/TRACK
button
(17) to move to the previous track or the following track. Track number shows on
display.
Hold TUNE/SEEK/TRACK
button (16) or TUNE/SEEK/TRACK
button
(17) to fast reverse or fast forward. CD play starts from when you release the button.
• PAUSE PLAYING
Press PAU button (20) to pause CD player. Press it again to resume play.
• REPEAT THE SAME TRACK
Press RPT button (22) to continuously repeat the same track. Press again to stop
repeat.
• PREVIEW ALL TRACKS
Press SCN button (21) to play first several seconds of each track on the current
disc. Press again to stop intro and listen to track.
• PLAY ALL TRACKS IN RANDOM
Press SHF button (23) to play all tracks on CD in random order. Press again to
cancel the function.
• EJECT
Press button (4) to stop CD playing and eject the disc from the disc slot (5).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 165 (D) x 50 (H)
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
: + 10 dB / – 10 dB
: + 10 dB / – 10 dB
: 40W x 4 (ch)
: 5 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 60 dB
: More than 60 dB
: 20 Hz - 20 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.7 MHz
: 3 µV
: > 30 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1710 KHz
: 450 KHz
: 32 dBu
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
The car ignition switch is
not on.
If the power supply is properly
connected to the car accessory
circuits, but the engine is not
moving, switch the ignition key
to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot be
loaded or ejected. the player.
Presence of CD disc inside Remove the disc in the player,
then put a new one.
Inserting the disc in reverse Insert the compact disc with
direction. the label facing upward.
Compact disc is extremely Clean the disc or try to play a
dirty or defective disc. new one.
Temperature inside the car Cool off or until the ambient
is too high.
temperature return to normal.
Condensation.
Leave the player off for an hour
or so, then try again.
No sound.
Volume is in minimum.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle less
than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
The operation keys The built-in microcomputer Press the RESET button.
do not work.
is not operating properly
due to noise.
Front panel is not properly fixed
into its place.
The radio does not The antenna cable is not
Insert the antenna cable firmly.
work. The radio
station automatic
selection does not The signals are too weak.
work.
connected.
Select a station manually.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|