43-739.fm Page 1 Friday, August 13, 1999 2:00 PM
Cat. No. 43-739
OWNER’S MANUAL
Please read before using this equipment.
TAD-739
Two-Line
Digital Telephone Answering System
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 3 Friday, August 13, 1999 2:00 PM
LED Message Counter — shows the
number of messages the TAD has re-
corded.
Warning: To prevent fire or shock
hazard, do not expose this prod-
uct to rain or moisture.
Programmable Remote Operation Se-
curity Code — lets you set your own
security code for remote operation.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
Remote Answer-On — lets you turn on
the TAD from a remote location even
when it is not set to answer calls.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
Room Monitor — lets you listen from a
remote phone to the room where the
TAD is installed.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
Memory Backup — protects messages
stored in memory in case of a power fail-
ure.
Your TAD-739 is ETL listed to UL stan-
dards and meets all applicable FCC
standards.
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 4 Friday, August 13, 1999 2:00 PM
READ THIS BEFORE IN-
STALLATION
FCC STATEMENT
Your TAD complies with Part 68 of FCC
Rules. You must, upon request, provide
the FCC registration number and the
REN to your phone company. Both num-
bers appear on the bottom of your TAD.
Your TAD-739 conforms to federal regu-
lations, and you can connect it to most
telephone lines. However, each device
that you connect to the phone line draws
power from the line. We refer to this
power draw as the device’s ringer equiv-
alence number, or REN. The REN is
shown on the label on the bottom of your
TAD.
Note: You must not connect your TAD
to:
• coin-operated systems
• party-line systems
If you are using more than one device
on the line, add up all the RENs. If the
total is more than five, your phone might
not ring and your TAD might not answer.
In rural areas, a total REN of three might
impair ringer operation. If ringer opera-
tion is impaired, remove one of the de-
vices from the line.
• most electronic key phone systems
This device compiles with Part 15 of
FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful
interference.
• This device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 5 Friday, August 13, 1999 2:00 PM
CONTENTS
Preparation .............................................................................................................. 6
Connecting to the Telephone Line(s) .................................................................. 6
Connecting the AC Adapter ................................................................................ 8
Installing a Backup Battery ................................................................................. 9
Setting the Day and Time ................................................................................... 9
Recording the Outgoing Messages .................................................................. 10
Checking the Outgoing Messages ............................................................. 11
Setting the Number of Rings ............................................................................ 11
Basic Operation .................................................................................................... 12
Setting the TAD to Answer Calls ...................................................................... 12
Incoming Message Recording .......................................................................... 12
Screening Calls ................................................................................................ 13
Playing Messages ............................................................................................ 13
Deleting Messages ........................................................................................... 14
Recording a Memo ........................................................................................... 15
Recording a Conversation ................................................................................ 15
Using Call Breakthrough .................................................................................. 16
Changing the CBT Code ............................................................................ 16
Changing the Remote Operation Security Code .............................................. 16
Remote Operation ................................................................................................. 17
Using the Toll-Saver ......................................................................................... 17
Using Remote Commands ............................................................................... 17
Remote Commands ................................................................................... 18
Troubleshooting .................................................................................................... 20
Resetting the TAD ............................................................................................ 20
Care And Maintenance ......................................................................................... 21
The FCC Wants You To Know .......................................................................... 22
Lightning ........................................................................................................... 22
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 6 Friday, August 13, 1999 2:00 PM
PREPARATION
Select a location for the TAD that is near modular telephone line jack(s) and an AC
outlet, and is not in the way of normal activities.
CONNECTING TO THE TELEPHONE LINE(S)
Your TAD connects to your phone(s) and phone line(s) using up to four modular tele-
phone line connectors. If your phone line(s) do not have modular jacks, you can up-
date the wiring yourself using adapters available at your local RadioShack store. Or,
you can have the telephone company update your telephone wiring for you.
Notes:
• If you connect the TAD to only one phone line, the TAD records messages for
that line only.
• The USOC number of the jack to be installed is RJ11C (for a single-line phone
jack) or RJ14C (for a two-line phone jack).
The following illustrations show the possible connections, depending on your tele-
phone and phone line setup:
For a Two-Line Phone and a Two-Line Phone Jack
For a Two-Line Phone and Two Single-Line Phone Jacks
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 7 Friday, August 13, 1999 2:00 PM
For a Single-Line Phone and a Two-Line Phone Jack
For Two Single-Line Phones and a Two-Line Phone Jack
For Two Single-Line Phones and Two Single-Line Phone Jacks
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 8 Friday, August 13, 1999 2:00 PM
• A1appears if you have not record-
ed announcement 1.
CONNECTING THE AC
ADAPTER
• A2appears if you have not record-
Caution: The supplied AC adapter was
designed specifically for your TAD-739.
Use only the supplied adapter.
ed announcement 2.
• Lo appears if a backup battery is
weak or missing.
AC 9V
1. Insert the supplied AC adapter’s
AC 9V
barrel plug into the
the back of the TAD.
jack on
2. Plug the other end of the adapter
into a standard AC outlet.
When you first connect power, the TAD
announces “Please wait,” then runs a
self-test for about 34 seconds. After the
test, the TAD beeps and Lo, L1, A1,
A2, L2, A1, A2, 0alternately appear in
the message counter window.
Note: The TAD’s message counter win-
dow usually shows the number of mes-
sages. That number alternates with
other displays to tell you the status of
the TAD.
•
L1 appears if you have not record-
ed the announcement (outgoing
message) 1 and/or announcement 2
in line 1.
• L2
appears if you have not recorded
the announcement 1 and/or an-
nouncement 2 in line 2.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 9 Friday, August 13, 1999 2:00 PM
Replace the battery when Loappears.
INSTALLING A BACKUP
BATTERY
Cautions:
If AC power fails or you unplug the TAD,
a 9V backup battery (not supplied)
saves the message groups, message
counts, and the settings for the day,
time, and security code. We recommend
you use an alkaline battery, such as Ra-
dioShack Cat. No. 23-553.
• Before you replace the battery, be
sure the TAD is properly connected
to AC power. Otherwise, you might
lose any stored information.
• Always remove old or weak battery.
Battery can leak chemicals that can
destroy electronic parts.
Caution: Always use a fresh battery of
the required size and recommended
type.
• Dispose of the old battery promptly
and properly. Do not burn or bury it.
1. Use a Phillips screwdriver to remove
the screw on the battery compart-
ment cover, then remove the cover.
SETTING THE DAY AND
TIME
To avoid losing the day and time settings
if AC power fails, we recommend you in-
stall a backup battery before you set the
day and time (see “Installing a Backup
Battery”).
Follow these steps to set the day and
time so the TAD can record the correct
day and time when each message and
memo is recorded.
2. Snap the battery’s contacts firmly to
the battery connector and place the
battery into the compartment.
Notes:
• If you do not complete each step
within 8 seconds, the TAD sounds
four beeps and exits setup. Start
again at Step 1.
VOLUME
• Be sure you set
at the right
side to an audible level so you can
hear the announcement.
3. Replace the cover and secure it with
the screw.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 10 Friday, August 13, 1999 2:00 PM
1. Hold TIME SET until the TAD sounds
one long beep and one short beep,
CL (clock) appears briefly, then a
number from 1 (Sunday)–7(Sat-
urday) appears, and the TAD an-
nounces the currently set day.
shortly, then the TAD announces the day
and time.
RECORDING THE
OUTGOING MESSAGES
Before the TAD-739 can answer calls
and record messages, you must record
an outgoing message (OGM). The TAD
lets you record two separate messages
of up to 32 seconds each, and it oper-
ates differently based on which mes-
sage you select.
2. To change the day of the week, re-
peatedly press REPEAT to move
backward or SKIP to move forward
until the TAD announces the desired
day of the week.
• OGM 1 – After playing your outgo-
ing message, the TAD records the
caller’s message.
• OGM 2 (announce-only) – The TAD
plays your outgoing message, but
does not record a message.
If you plan to use the TAD’s
3. Press TIME SET. The TAD announc-
announce-only feature, OGM
2
es the preset hour.
should clearly state that the caller
cannot leave a message.
4. To change the hour (from 01 to 12),
repeatedly press REPEAT or SKIP.
Do not tell the callers that you are
Hint:
out of town or not home. Instead, say
that you cannot come to the phone right
now.
5. Press TIME SET. The TAD announc-
es the preset minute.
6. To change the minutes (from 00 to
59), repeatedly press REPEAT or
SKIP.
: The maximum length for each out-
Note
going message is 32 seconds. As you
record, the message counter shows the
recording time.
7. Press TIME SET to confirm the set-
tings. The TAD sounds one long
beep and one short beep, then an-
nounces the day and time.
Follow these steps to record your outgo-
ing message.
To check the current day/time at any
time, press TIME SET. CL (clock) and
then the preset date and time appear
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 11 Friday, August 13, 1999 2:00 PM
1. To record the OGM 1 (or OGM 2)
message for each line, hold down
OGM 1 (or OGM 2) until the TAD
beeps and both ANSWER indicators
flash.
cators flash. Then press ANSWER within
8 seconds on the selected line and the
message plays after the beep.
If there is no announcement recorded,
you hear “You have no announcement
one (or “two”) in line one (or “two”)”
when you press its button.
:
Notes
• Proceed next step within 8 seconds.
Otherwise, the TAD sounds a short
beep, and you must start again from
Step 1.
SETTING THE NUMBER
OF RINGS
• Recording OGM 2 only does not
turn on the TAD. You must start re-
cording OGM from OGM 1.
Set each line’s ring select switch to 2, 4,
7, or TS to set how long the TAD waits
before it answers a call (2 rings, 4 rings,
7 rings or toll-saver).
2. Press ANSWER above the desired
LINE 1 or LINE 2, and speak your
message from about 8 inches from
the front of the TAD.
If you plan to check your messages by
long distance, set the ring select switch
to TS (see “Using the Toll-Saver” on
Page 17).
3. When you finish, press STOP. The
TAD beeps and plays back the out-
going message.
: When you finish recording
Note
OGM 1 only, the TAD automatically
sets to answer on. The ANSWER in-
dicator above LINE 1 lights.
Checking the Outgoing
Messages
To check an outgoing message, press
its button (OGM 1 or OGM 2). You see
the announcement number A1 or A2,
the TAD beeps and both ANSWER indi-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 12 Friday, August 13, 1999 2:00 PM
BASIC OPERATION
SETTING THE TAD TO
ANSWER CALLS
INCOMING MESSAGE
RECORDING
The ANSWER indicator lights to indicate
which line the TAD is set to answer on;
or announce only. A steady light indi-
cates the line is set to answer on. A
flashing light indicates the line is set to
announce only.
When the TAD is set to answer calls us-
ing OGM 1, it plays the outgoing mes-
sage, then beeps. The caller can then
record a message up to 60 seconds
long.
When a recording reaches 55 seconds,
the TAD beeps to notify the caller that
time will soon be up. At 60 seconds, the
TAD sounds a long beep and four short
beeps, says “Thank you for your call,”
and hangs up.
To set the TAD to answer calls after you
have recorded OGM 1 and OGM 2, or
only OGM 1, press ANSWER on the se-
lected line. The TAD announces “Line x
(line number) is on.” A1 appears, and
the TAD beeps and plays the outgoing
message. The ANSWER indicator lights
to show that the TAD is ready to answer
calls and record caller’s messages.
The TAD stops recording and resets to
answer the next call when:
• the caller hangs up
• the maximum message length is
reached
• there are more than 7 seconds of si-
lence
• you pick up any phone on the same
line as the TAD
To set the TAD to not answer calls,
press ANSWER on the selected line
again. The TAD announces “Line x (line
number) is off.” The ANSWER indicator
turns off.
If the TAD’s memory is full, FLand the
number of recorded messages alter-
nately appear. It answers calls after 3
rings and plays the announce-only mes-
sage (OGM 2). If no OGM 2 is recorded,
the TAD says “Memory is full, thank you
for your call.” and beeps once. Then the
TAD beeps once again after 8 seconds.
To set the TAD to play an outgoing mes-
sage but not let callers leave a mes-
sage, press ANSWER on the selected
line again. Ao(announce only) appears,
the TAD says “Line x (line number) is
announce only” and beeps, then A2
briefly appears, and plays OGM 2. The
ANSWER indicator flashes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 13 Friday, August 13, 1999 2:00 PM
Notes:
PLAYING MESSAGES
• The maximum recording capacity is
32 minutes or 59 messages.
The TAD’s message counter window
shows the total number of messages,
both old and new. If there are new mes-
sages, the line indicators flash to let you
know which line has new messages.
• Many local phone companies use
calling party control (CPC) to signal
that the caller has hung up. Your
TAD recognizes a CPC signal and
releases the line. If the TAD records
phone company messages or dial
tones, your local phone company
probably does not use CPC.
Note: The TAD’s message counter win-
dow might also alternately show other
information to tell you the status of the
TAD.
• L1 appears if you have not record-
ed the announcement (outgoing
message) 1 and/or announcement 2
in line 1.
SCREENING CALLS
To screen calls, let the TAD answer
them, then listen to the caller’s message
through the TAD’s speaker. To adjust the
• L2 appears if you have not recorded
the announcement 1 and/or an-
nouncement 2 in line 2.
VOLUME
volume, slide
of the TAD.
on the right side
• A1 appears if you have not record-
ed announcement 1.
• A2 appears if you have not record-
ed announcement 2.
• Lo appears if a backup battery is
weak or missing.
If you decide to answer the call, pick up
any phone on the same phone line as
the TAD. The TAD stops recording and
resets to answer the next call.
To play all messages in line 1 or line 2,
PLAY
press that line’s
button. The TAD
announces the number of messages re-
corded in the selected mailbox, each
message number, and the day and time
the message was recorded, and then
plays the message.
If you do not want to take the call, simply
let the TAD finish recording the caller’s
message.
Note: If you answer the phone just as
the TAD answers, the TAD might not
stop playing the outgoing message. If
STOP
this happens, press
on the TAD.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 14 Friday, August 13, 1999 2:00 PM
To play only new messages, hold down
the desired PLAY button for 2 seconds.
The TAD tells you how many new mes-
sages you have in that line and plays
them.
move to any place within it. To resume
normal playback, release SKIP.
To stop playback at any time, press
STOP. The TAD beeps and resets to an-
swer calls.
After all messages play, the TAD says,
“End of messages.”
DELETING MESSAGES
To replay a message during playback,
press REPEAT. The current message
starts again from the beginning.
To delete the current message during
playback, press DELETE. The TAD an-
nounces “Erase.” and beeps, then plays
the next message.
To return to a previous message, hold
down REPEAT until you see the desired
message number.
To delete all messages in a line after
playback, hold down DELETE until the
TAD says “Erase messages” and beeps.
dLappears and the selected line indica-
tor next to each PLAY button that has
“played” messages flashes. Press the
selected line’s PLAY button. The TAD
sounds a long beep to confirm that all
messages in the selected line are delet-
ed.
To skip to the next message, press SKIP.
To pause during playback, press the se-
lected line’s PLAY button. PA (pause)
appears. To resume playback, press the
selected line’s PLAY button again within
60 seconds. Otherwise, the TAD stops
playback, announces “End of messag-
es,” and displays the total number of
messages.
:
Notes
• The TAD does not delete unplayed
messages. If you press DELETE
when you have unplayed messag-
es, the TAD sounds four beeps.
To quickly play a message, hold down
SKIP. The playback speed increases, al-
lowing you to quickly scan a message or
• To cancel the delete function soon
after you press DELETE, press
STOP/TIME SET. The TAD sounds
four beeps.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 15 Friday, August 13, 1999 2:00 PM
RECORDING A MEMO
RECORDING A
CONVERSATION
A memo is a message you can record at
the TAD for yourself or others. You can
record memos of up to 60 seconds long
in each line.
You can record both sides of a conver-
sation on any phone connected to the
same phone line as the TAD.
Memos are stored with incoming mes-
sages, and are replayed the same way
(see “Playing Messages” on Page 13).
Note: It is illegal in some areas to record
a conversation without the consent of all
parties to the conversation, including the
phone company. Check the laws in your
area before you use the two-way record-
ing feature.
Follow these steps to record a memo.
MEMO.
1. Press
appears, the TAD
beeps, and both line indicators
flash.
MEMO
1. Hold down
until the display
to 2R. The TAD
changes from
beeps, and both line indicators
flash.
PLAY
2. Press
of the desired line and
begin speaking in a normal voice af-
ter the beep. The display counts up
the recording time.
PLAY
2. Press
of the desired line. The
selected line indicator lights and re-
cording begins.
PLAY
Note: Press
within 8 seconds
after both line indicators start flash-
ing. Otherwise, the TAD sounds a
short beep, and you must start
again from Step 1.
PLAY
Note: Press
within 5 seconds
after both line indicators start flash-
ing. Otherwise, the TAD sounds a
short beep, and you must start
again from Step 1.
3. The TAD automatically stops record-
ing after 60 seconds, or you can
3. The TAD records until:
STOP
press
when you finish the
memo. The TAD beeps once, and
the message number indicator in-
creases by one.
STOP
• you press
• there is an 8-second busy signal
or 25 seconds of silence
• the TAD’s memory becomes full
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 16 Friday, August 13, 1999 2:00 PM
SKIP
REPEAT
or
4. Repeatedly press
to set the second and third digits,
STOP
USING CALL
BREAKTHROUGH
pressing
after each digit. The
TAD beeps and announces the new
CBT code.
If you screen your calls but want to know
when calls come in from certain people,
give them your call breakthrough (CBT)
code.
CHANGING THE REMOTE
OPERATION SECURITY
CODE
When a caller enters the CBT code dur-
ing the outgoing message, the TAD
alerts you with a series of loud beeps for
35 seconds. To answer the call, pick up
the handset. If you do not answer, the
caller can leave a message after the
outgoing message plays.
The remote operation security code is
preset to 739, but you can change it by
following these steps. Do not use the
same number you choose for the CBT
code.
Changing the CBT Code
Note: Be sure to complete each step
within 8 seconds. Otherwise, the TAD
beeps four times and you must start
over from Step 1.
The CBT code is preset to 648, but you
can change it by following these steps.
Note: Be sure to complete each step
within 8 seconds. Otherwise, the TAD
beeps four times and you must start
over from Step 1.
CODE
1. Hold down
until the TAD
beeps. Co(code) appears.
CODE
2. Press
again. Sc (security
code) appears, and the TAD an-
nounces and displays the current
code’s numbers (739) in sequence.
Then the first digit of the code ap-
pears.
CODE
1. Hold down
until the TAD
beeps. Co(code) appears.
SKIP
REPEAT
or
3. Repeatedly press
STOP
to set the first digit, then press
The second digit appears.
.
REPEAT
2. Press
. Cc (CBT code) ap-
pears, and the TAD announces and
shows the current code’s numbers
in sequence. Then the first digit of
the code reappears.
SKIP
REPEAT
or
4. Repeatedly press
to set the second and third digits,
STOP
pressing
after each digit. The
TAD beeps and announces the new
remote operation security code.
SKIP
REPEAT
or
3. Repeatedly press
STOP
to set the first digit, then press
The second digit appears.
.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 17 Friday, August 13, 1999 2:00 PM
REMOTE OPERATION
While you are away from your home or
office, you can use a touch-tone phone
or a pulse (rotary) phone with a pocket
tone dialer to enter your remote opera-
tion security code and do any of the fol-
lowing:
USING REMOTE
COMMANDS
Follow these steps to operate the TAD
remotely.
1. Dial either one of your phone num-
ber which you connected with the
TAD.
• set the TAD to answer calls
• listen to your messages
• record a new announcement
• record a memo
2. When the TAD answers, enter your
remote operation security code. The
TAD beeps once to confirm that you
entered the correct code.
• delete messages
• monitor the room where the TAD is
located
Notes:
• If you do not enter each digit of
the security code within 8 sec-
onds, the TAD hangs up.
Note: You cannot remotely operate the
TAD from another phone on the same
line as your TAD-739.
• Even if the TAD is not set to an-
swer calls, it will answer after
about 9 rings.
USING THE TOLL-SAVER
3. Enter a remote command (see “Re-
mote Commands” on Page 18).
If the ring select switch is set to TS (toll-
saver) (see “Setting the Number of
Rings” on Page 11), the TAD answers
after two rings if you have new messag-
es. If there are no new messages, the
TAD waits for four rings before it an-
swers. This gives you time to hang up
before the TAD answers so you can
avoid unnecessary long-distance charg-
es.
4. When you finish, simply hang up.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 18 Friday, August 13, 1999 2:00 PM
Remote Commands
Press:
To:
#0
Set the TAD to announce only
for both lines. It says “Line 1 is
announce-only, line 2 is
Press:
To:
[0
Set the TAD to not answer
calls for both lines. The TAD
says “Line 1 is off, line 2 is off.”
announce-only.” If no OGM 2
is recorded in line 1, it says
“You have no announcement
two in line 1.” Then it sounds
four beeps and says “Line 2 is
announce-only.” If no OGM 2
is recorded in line 2, it says
“Line 1 is announce-only. You
have no announcement two in
line 2.” Then it sounds four
beeps.
[1
[2
Set the TAD to not answer
calls only for line 1. The TAD
says “Line 1 is off.”
Set the TAD to not answer
calls only for line 2. It says
“Line 2 is off.”
00
Set the TAD to answer calls
for both lines. It says “Line 1 is
on, line 2 is on.” If no OGM 1
is recorded in line 1, it says
“You have no announcement
one in line 1,” and sounds four
beeps, then says “Line 2 is
on.” If no OGM 1 is recorded
in line 2, the TAD says “Line 1
is on, you have no announce-
ment one in line 2.” then
#1
#2
Set the TAD to announce only
for line 1. It says “Line 1 is
announce-only.” If no OGM2 is
recorded, it says “You have no
announcement two in line 1.”
Press 91[ to record OGM2.
Set the TAD to announce only
for line 2. It says “Line 2 is
announce-only.” If no OGM2 is
recorded, it says “You have no
announcement two in line 2.”
Press 92[ to record OGM2
sounds four beeps.
01
02
Set the TAD to answer calls
only for line 1. It says “Line 1 is
on.” If no OGM 1 is recorded
in line 1, it says “You have no
announcement one in line 1.”
and sounds four beeps. Press
81[ to record OGM 1.
2, then
Play all messages in the
line num-
ber (0, 1,
2)
selected line. If no message is
recorded, the TAD says “You
have no messages in line x.”
(0 for both (where x is the line number). If
lines, 1 for no messages are recorded in
line 1, and both lines, the TAD says “You
2 for line
2)
Set the TAD to answer calls
only for line 2. It says “Line 2 is
on.” If no OGM 1 is recorded
in line 2, it says “You have no
announcement one in line 2.”
and sounds four beeps. Press
82[ to record OGM 1.
have no messages in line 1,
and no messages in line 2.”
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 19 Friday, August 13, 1999 2:00 PM
Press:
To:
Press:
82#
To:
3, then
Play new messages in the
Play line 2’s OGM 1. If no OGM
1 is recorded, the TAD
announces “You have no
line num- selected line. If no new mes-
ber (0, 1, sage is recorded, the TAD says,
2)
“You have no new messages in
line x.” (where x is the line num-
ber). If no new messages are
recorded in both lines, the TAD
says, “You have no new mes-
sages in line 1 and no new
messages in line 2.”
announcement one in line two.”
91[
92[
Change line 1’s OGM 2. After
the TAD beeps, speak your
message. When you finish,
press 6. The TAD beeps and
replays your new OGM.
Change line 2’s OGM 2. After
the TAD beeps, speak your
message. When you finish,
press 6. The TAD beeps and
replays your new OGM.
4
Monitor the room where you
installed the TAD for 20 sec-
onds. Press 4 again to repeat.
5, then
Delete all played new mes-
line num- sages from the selected line.
ber (0, 1, After the TAD says “Erase mes-
91#
92#
Play line 1’s OGM 2. If no OGM
2 is recorded, the TAD
announces “You have no
2)
sages,” press the line number
to delete played messages in
that line.
announcement two in line one.”
Play line 2’s OGM 2. If no OGM
2 is recorded, the TAD
announces “You have no
6
Stop playback and message
recording.
7, then
Record a memo in the selected
announcement two in line two.”
line num- line.
ber (1, 2)
While playing messages:
81[
82[
81#
Change line 1’s OGM 1. After
the TAD beeps, speak your
message. When you finish,
press 6. The TAD beeps and
replays your new OGM.
Press:
To:
1
3
4
5
6
Replay previous message.
Skip to next message.
Play line 2’s OGM 1. After the
TAD beeps, speak your mes-
sage. When you finish, press 6.
The TAD beeps and replays
your new OGM.
Replay current message.
Delete current message.
Stop message playback.
Play line 1’s OGM 1. If no OGM
1 is recorded, the TAD
announces “You have no
announcement one in line one.”
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 20 Friday, August 13, 1999 2:00 PM
TROUBLESHOOTING
We do not expect you to have any problems with your TAD-739, but if you do, try
these suggestions.
Problem
Remedy
The incoming message is incom- Be sure the memory is not full.
plete.
The incoming message is unclear. Be sure VOLUME is set to the desired sound
level.
Check all phone line connections.
The TAD does not answer after
two, four, or seven rings.
Be sure the TAD is set to answer calls.
Check all phone line connections.
Be sure the AC adapter is properly connected.
Loappears on the display.
The backup battery is weak. Replace the bat-
tery (see “Installing a Backup Battery” on
Page 9).
The TAD does not respond to the Make sure the phone you used to dial the TAD
remote operation security code.
is a touch-tone phone. If it is not, you can use a
pocket tone dialer to remotely operate the TAD.
Re-enter your remote operation security code,
pressing each button for 2 seconds.
Enter the default remote operation security
code (739). The code might have been reset to
its default value due to a power failure.
If the TAD still does not operate properly, try resetting it (see “Resetting the TAD”) or
take it to your local RadioShack store for assistance.
RESETTING THE TAD
If your TAD stops working properly,
use a straightened paper clip to press
RESET
RESET on the back of the TAD to reset
the answering machine.
Note: Resetting the TAD erases your
outgoing messages and all stored in-
formation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 21 Friday, August 13, 1999 2:00 PM
CARE AND MAINTENANCE
Your RadioShack TAD-739 Two-Line Digital Telephone Answering System is an ex-
ample of superior design and craftsmanship. The following suggestions will help you
care for your TAD-739 so you can enjoy it for years.
Keep the TAD-739 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the TAD-739 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the TAD-739 away from dust and dirt, which can cause premature
wear of parts.
Handle the TAD-739 gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the TAD-739 to work improperly.
Use only fresh battery of the required size and type. Battery can leak
chemicals that damage your TAD-739’s electronic parts.
Wipe the TAD-739 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the TAD-739.
Modifying or tampering with the TAD-739’s internal components can cause a mal-
function and might invalidate your TAD-739’s warranty and void your FCC authoriza-
tion to operate it. If your TAD-739 is not performing as it should, take it to your local
RadioShack store for assistance. If the trouble is affecting the telephone lines, the
phone company can ask you to disconnect your TAD-739 until you have resolved the
problem.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 22 Friday, August 13, 1999 2:00 PM
THE FCC WANTS YOU TO
KNOW
LIGHTNING
Your TAD has built-in protection circuits
to reduce the risk of damage from surg-
es in phone and power line current.
These protection circuits meet or ex-
ceed FCC requirements. However, light-
ning striking the phone line or power
lines can damage your TAD.
In the unlikely event that your TAD caus-
es problems on the phone line, the
phone company can temporarily discon-
nect your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your TAD during storms
to reduce the possibility of damage.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of your TAD. The phone com-
pany notifies you of these changes in
advance, so you can take steps to pre-
vent interruption of your phone service.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 23 Friday, August 13, 1999 2:00 PM
NOTES
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-739.fm Page 24 Friday, August 13, 1999 2:00 PM
Limited One-Year Warranty
This product is warranted by Radio Shack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from Radio Shack company-
owned stores and authorized Radio Shack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RADIO SHACK MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRAN-
TIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED
WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RADIO SHACK SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR EN-
TITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDI-
RECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM
INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDI-
RECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RADIO SHACK HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the Radio Shack
sales receipt as proof of purchase date to any Radio Shack store. Radio Shack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of Radio Shack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a Radio Shack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Radio Shack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
1A9
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|