$KI"$WVVQP"#ORNKHKGF"35//GOQT["2JQPG
43-3241
OWNER’S MANUAL — Please read before using this equipment.
(%%"56#6'/'06
"+/2146#06"
#
#
If an icon appears at the end of a paragraph,
go to the box on that page with the
corresponding icon for pertinent information.
Your telephone complies with Part 68 of
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
FCC Rules. You must, upon request,
provide the FCC registration number and the
REN (see below) to your telephone
company. Both numbers are on the bottom
of your phone. ±
— Warning
— Important
#
Rý
± — Note
Also, the phone company can make
. — Caution
° — Hint
changes to its lines, equipment, operations,
or procedures that could affect the operation
of this telephone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
We have designed your telephone to
conform to federal regulations, and you can
connect it to most telephone lines. However,
each telephone (and each device, such as a
telephone or answering machine) that you
connect to the telephone line draws power
from the telephone line. We refer to this
power draw as the device's ringer
WARNING: To reduce the risk of fire or shock hazard, do not expose this
product to rain or moisture.
CAUTION: TO REDUCE THE
..CAUTION..
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER OR BACK.
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
RISK OF ELECTRIC
!
SHOCK DO NOT OPEN
The lightning symbol is intended to
alert you to the presence of uninsulated
dangerous voltage within this
The exclamation symbol is
intended to inform you that
important operating and
.+)*60+0)
!
product’s enclosure that might be of
maintenance instructions are
included in the literature accompanying
this product.
sufficient magnitude to constitute a risk of electric
shock. Do not open the product’s case.
Your telephone has built-in protection
circuits to reduce the risk of damage from
surges in telephone line and power line
current. These protection circuits meet or
exceed the FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
equivalence number, or REN on the bottom
of your phone.
If you use more than one phone or other
device on the line, add up all of the RENs. If
the total is more than five (three in rural
areas), your telephones might not ring. If
ringer operation is impaired, remove a
device from the line.
±"016'"±"
FCC Statement
You must not connect your telephone to:
•
•
•
coin-operated systems
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that
you unplug your phone when storms
approach to reduce the possibility of
damage.
party-line systems
most electronic key telephone systems
In the unlikely event that your phone causes
problems on the phone line, the phone
company can temporarily discontinue your
service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
Connecting the Phone
•
The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall
plate jack).
Your phone is ETL listed to UL standards
and meets applicable FCC requirements.
•
You can set the phone on a flat surface or
mount it directly on a wall or a wall plate
using the supplied mounting bracket.
%100'%6+0)"6*'"2*10'
Your telephone connects directly to a
modular telephone line jack. If your
telephone wiring does not have a modular
jack, you can update the wiring yourself
using jacks and adapters (available at your
local RadioShack store), or have the
telephone company update the wiring for
you. You must use compatible modular
jacks that are compliant with Part 68 of FCC
Rules. ±
supplied) into each hole, letting the heads
3
16
extend about / inch (5 mm) from the wall.
Connect the supplied long modular cord to
the phone’s line jack. Fit the keyhole slots
over the screw heads and slide the phone
downward to secure it. Plug the line cord
into the telephone line jack.
To mount the phone on a wall plate, connect
the supplied short modular cord as shown.
Fit the keyhole slots over the wall plate studs
and slide the phone downward to secure it.
Position the supplied mounting bracket so
the mounting hole’s open end is facing
downward, then insert the supplied
mounting bracket’s two tabs into the
matching slots on the bottom of the base,
then snap the bracket into place.
To mount the
phonedirectly
on a wall, drill
Before you hang up the handset on a wall-
mounted phone, slide up the handset holder
out of its slot, turn it, and slide it back into its
slot.
two holes
15
16
3 / inches
(100 mm)
apart. Then
thread a
Plug the handset cord into the jacks on the
handset and the base.
screw (not
© 2002 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|