OPERATOR’S MANUAL
7-1/4 in. WORM DRIVE SAW
DOUBLE INSULATION
R3210-1
Your saw has been engineered and manufactured to our high standards for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites acci-
dents.
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Keep your work area clean and well lit. Cluttered
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
ELECTRICAL SAFETY
TOOL USE AND CARE
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Use clamps or other practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
Do not force tool. Use the correct tool for your appli-
cation. The correct tool will do the job better and safer
at the rate for which it is designed.
Double insulation
eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
Disconnect the plug from power source before mak-
ing any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
When operating a power tool outside, use an outdoor ex-
tension cord marked “W-A” or “W”. These cords are rated
for outdoor use and reduce the risk of electric shock.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Fol-
lowing this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to fol-
low Maintenance Instructions may create a risk of shock
or injury.
SERVICE
Tool service must be performed only by qualified re-
pair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
DANGER! Keep hands away from cutting area and
blade. Keep your second hand on the auxiliary handle,
or motor housing. If both hands are holding the saw,
they cannot be cut by the blade.
Always use blades with correct size and shape (dia-
mond vs. round) arbor holes. Blades that do not match
the mounting hardware of the saw will run eccentrically,
causing loss of control.
Keep your body positioned to either side of the saw
blade, but not in line with the saw blade. Kickback
could cause the saw to jump backwards. (See “Causes
and Operator Prevention of Kickback.”)
Never use damaged or incorrect blade washers or
bolts. The blade washers and bolts were specially de-
signed for the saw for optimum performance and safety
of operation.
Do not reach underneath the work. The guard can not
CAUSES AND OPERATOR PREVENTION OF
protect you from the blade below the work.
KICKBACK
Check lower guard for proper closing before each
use. Do not operate saw if lower guard does not
move freely and close instantly. Never clamp or tie
the lower guard into the open position. If saw is ac-
cidentally dropped, lower guard may be bent. Raise the
lower guard with the Retracting Handle and make sure it
moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
Kickback is a sudden reaction to a pinched, bound, or mis-
aligned saw blade, causing an uncontrolled saw to lift up
and out of the workpiece toward the operator.
When the blade is pinched or bound tightly by the kerf clos-
ing down, the blade stalls and the motor reaction drives the
unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
Check the operation and condition of the lower guard
spring. If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
Kickback is the result of tool misuse and/or incorrect operat-
ing procedures or conditions and can be avoided by taking
proper precautions, as given below:
Lower guard should be retracted manually only for
special cuts, such as “Pocket Cuts” and “Compound
Cuts.” Raise lower guard by retracting handle. As
soon as blade enters the material, lower guard must
be released. For all other sawing, the lower guard should
operate automatically.
Maintain a firm grip with both hands on the saw and
position your body and arm to allow you to resist
KICKBACK forces. KICKBACK forces can be controlled
by the operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from
the work or pull the saw backward while the blade is
in motion, or KICKBACK may occur. Investigate and
take corrective actions to eliminate the cause of blade
binding.
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after switch is re-
leased.
NEVER hold piece being cut in your hands or across
your leg. It is important to support the work properly to
minimize body exposure, blade binding, or loss of con-
trol.
When restarting a saw in the workpiece, center the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding,
it may walk up or KICKBACK from the workpiece as the
saw is restarted.
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near the
edge of the panel.
When ripping always use a rip fence or straight edge
guide. This improves the accuracy of the cut and reduces
the chance for blade binding.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 12 is rec-
ommended for an extension cord 50 feet or less in
length. A cord exceeding 50 feet is not recommended.
If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord. An undersized cord
will cause a drop in line voltage resulting in loss of power
and overheating.
Do not use dull or damaged blade. Unsharpened or
improperly set blades produce narrow kerf causing ex-
cessive friction, blade binding and KICKBACK.
Blade depth and bevel adjusting locking levers must
be tight and secure before making cut. If blade ad-
justment shifts while cutting, it may cause binding and
KICKBACK.
Use extra caution when making a “Pocket Cut” into
existing walls or other blind areas. The protruding blade
may cut objects that can cause KICKBACK.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
ADDITIONAL SAFETY RULES
Inspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Drugs, alcohol, medication. Do not operate tool while
under the influence of drugs, alcohol, or any medica-
tion. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
If the power supply cord is damaged, it must be re-
placed only by the manufacturer or by an authorized
service center to avoid risk.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and, as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this
product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to
use this product until you read thoroughly and un-
derstand completely the operator’s manual. If you
do not understand the warnings and instructions in
the operator’s manual, do not use this product. Call
RIDGID customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is desig-
nated with “WA” on the cord’s jacket.
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protect-
ing insulation. Double insulated tools do not need to be
grounded.
Before using any extension cord, inspect it for loose or ex-
posed wires and cut or worn insulation.
**Ampere rating (on tool faceplate)
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
WARNING:
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
The double insulated system is intended to protect
the user from shock resulting from a break in the
tool’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
100'
**Used on 12 gauge - 20 amp circuit.
Servicing of a tool with double insulation requires extreme
care and knowledge of the system and should be performed
only by a qualified service technician. For service, we sug-
gest you return the tool to your nearest authorized service
center for repair. Always use original factory replacement
parts when servicing.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can result
in serious personal injury.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged
cord since touching the damaged area could cause
electrical shock resulting in serious injury.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An un-
dersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
SPECIFICATIONS
Blade Diameter...........................................................................................................................................7-1/4 in. (184 mm)
Blade Arbor .................................................................................................................................. Diamond (Bolt-LH Combo)
Cutting Depth at 90°..................................................................................................................................2-3/8 in. (60.3 mm)
Cutting Depth at 45°..................................................................................................................................1-3/4 in. (44.5 mm)
Cutting Depth at 51.5°.............................................................................................................................1-9/16 in. (39.7 mm)
Input .............................................................................................................................. 120 Volts, 60 Hz, AC only, 15 Amps
No Load Speed ..........................................................................................................................................4400 r/min. (RPM)
Net Weight.....................................................................................................................................................15.0 lbs. (6.8 kg)
KNOW YOUR WORM DRIVE SAW
SPINDLE LOCK
See Figures 1 and 1a.
The spindle lock allows you to secure the blade when turn-
ing the blade screw.
The safe use of this product requires an understanding of the
information on the tool and in this operator’s manual as well
as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
SKYHOOK™ SAW HANGER
This feature allows the saw to hang on any framing
material.
NOTE: Do not run the saw with the spindle lock engaged.
SHOCK ABSORBING REAR HANDLE
The soft grip handle is designed for durability and operator
comfort.
FULL LENGTH KERF INDICATOR
Indicates blade position for more accurate cutting.
ERGONOMIC DESIGN
51.5° BEVEL BRACKET
The design provides for easy handling. It is designed for
comfort and ease of grasp when operating in different posi-
tions and at different angles.
The bevel bracket provides more flexibility while cutting.
24 TOOTH CARBIDE BLADE
The high-quality carbide blade helps to create smooth
cuts.
POWER CORD
The 12-foot cord has a built-in cord wrap.
HIGH STRENGTH ALUMINUM BASE
The strength of the aluminum base enhances durability.
LIGHTED PLUG
The lighted plug helps to easily identify live tools.
OVERSIZED LEVERS
This feature makes it more convenient for the operator to
adjust depth and bevel settings.
DIPSTICK
A dipstick is provided for checking the oil level and correctly
refilling the saw with oil.
SWITCH TRIGGER
The saw has a conveniently-located ON/OFF switch
trigger.
DIPSTICK AND WRENCH STORAGE
A convenient storage area for the dipstick and the wrench is
located on the underside of the rear handle of the tool.
LENGTH OF CUT SCALE
The saw is equipped with a length of cut scale on its base.
The operator can use it to measure the distance the blade
cuts into the material.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
REAR
HANDLE
SWITCH
TRIGGER
FRONT HANDLE
POWER
CORD
OVERSIZE LEVER
(DEPTH
ADJUSTMENT)
OVERSIZE LEVER
(BEVEL ADJUSTMENT)
ALUMINUM BASE
LENGTH OF
CUT SCALE
FULL LENGTH
KERF INDICATOR
DIPSTICK
LIGHTED PLUG
Fig. 1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
SKYHOOK™
SAW HANGER
SPINDLE
LOCK
51.5° BEVEL
BUTTON
DIPSTICK
AND WRENCH
STORAGE
Fig. 1a
UNPACKING
PACKING LIST
INSTRUCTIONS:
7-1/4 in. (184 mm) Worm Drive Saw
24-Tooth Carbide Tipped Blade
Hex Wrench
When unpacking the tool:
Carefully remove the tool and accessories from the box.
Make sure that all items listed in the packing list are in-
cluded.
Dipstick
Inspect the tool carefully to make sure no breakage or
Operator’s Manual
damage occurred during shipping.
Do not discard the packing material until you have care-
WARNING:
fully inspected and satisfactorily operated the tool.
If any parts are missing do not operate the tool un-
til the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
If any parts are damaged or missing, please call 1-866-
539-1710 for assistance.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
WARNING:
Do not connect the tool to a power supply until all
assembly is complete. Failure to comply could result
in accidental starting and possible serious injury.
SPINDLE
OUTER
FLANGE
WASHER
WARNING:
7-1/4 in. (184 mm) blade is the maximum blade
capacity of the saw. Also, never use a blade that is
too thick to allow outer flange washer to engage with
the flat on the spindle. Larger blades will come in
contact with the blade guards, while thicker blades
will prevent blade screw from securing blade on
spindle. Either of these situations could result in a
serious accident.
INNER FLANGE
BUSHING
BLADE
BLADE
SPRING
WASHER
SCREW
ATTACHING BLADE
See Figures 2 and 2a.
Fig. 2
Unplug the saw.
OUTER FLANGE
WASHER
CAUTION:
To prevent damage to the spindle or spindle lock,
always allow motor to come to a complete stop
before engaging spindle lock.
Depress the spindle lock button.
Remove the blade screw by turning it clockwise with the
wrench, while keeping the lock button depressed.
Remove the spring washer and outer flange washer.
Wipe a drop of oil onto the inner flange bushing and outer
flange washer where they contact the blade.
OUTSIDE OF SPRING
WASHER
CUPPED SIDE OF
SPRING WASHER
WARNING:
Fig. 2a
If inner flange bushing has been removed, replace
it before placing blade on spindle. Failure to do so
could cause an accident since blade will not tighten
properly.
Fit the saw blade inside the lower blade guard and onto
the spindle.
NOTE: Be sure that the diamond key on the inner flange
bushing aligns properly with the blade before tightening
the blade screw.
Retract the lower guard into the upper guard, making
sure the lower guard spring works properly, allowing the
guard to move freely.
Replace outer flange washer.
Replace spring washer.
Check to see that the saw teeth and arrow on the saw
blade and the arrow on the lower guard are pointing in
the same direction.
Depress the spindle lock and replace the blade screw.
Tighten the blade screw securely by turning it counter-
NOTE: The saw teeth point upward at the front of the
clockwise with the wrench. Do not over tighten.
saw as shown.
NOTE: Never use a blade that is too thick to allow
the outer flange washer to engage with the flat on the
spindle.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
REMOVING BLADE
See Figure 3.
Unplug the saw.
CAUTION:
To prevent damage to the spindle or spindle lock,
always allow motor to come to a complete stop
before engaging spindle lock.
Depress spindle lock button.
Remove blade screw by turning it clockwise with the hex
wrench.
SPINDLE
LOCK BUTTON
Remove spring washer.
WRENCH
BLADE
Remove outer flange washer.
Lift lower blade guard.
Remove blade.
SCREW
Fig. 3
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Do not allow familiarity with the tool to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
APPLICATIONS
You may use this saw for the following purposes:
Cutting all types of wood products (lumber, plywood,
paneling)
NOTE: The use of abrasive cut-off wheels is not recom-
mended for this saw.
LOWER
BLADE GUARD
WARNING:
Fig. 4
The use of this saw on materials not listed may
damage the saw and its guards, and may cause
serious personal injury.
WARNING:
To avoid possible serious injury, never use saw when
guard is not operating correctly. Check the guard for
correct operation before each use. The guard is op-
erating correctly when it moves freely, and instantly
returns to the closed position. If you drop the saw,
check the lower blade guard and bumper for dam-
age at all depth settings before reuse.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes,
resulting in possible serious injury.
If at any time the lower blade guard does not snap closed,
unplug the saw from the power supply. Exercise the lower
guard by moving it rapidly back and forth from the full open
position to the closed position several times. Normally this
will restore the guard to its normal operating condition. If
it does not correct a slow or sluggish closing lower guard,
do not use the saw. Take it to an authorized factory service
center for repair.
SAW BLADES
The best of saw blades will not cut efficiently if they are not
kept clean, sharp, and properly set. Using a dull blade will
place a heavy load on the saw and increase the danger of
kickback. Keep extra blades on hand, so that sharp blades
are always available.
Gum and wood pitch hardened on blades will slow the saw
down. Remove saw blade from the saw and use gum and
pitch remover, hot water, or kerosene to remove these ac-
cumulations. DO NOT USE GASOLINE.
BLADE GUARD SYSTEM
See Figure 4.
The lower blade guard attached to your saw is there for
your protection and safety. Do not alter it for any reason.
If it becomes damaged, do not operate the saw until you
have the guard repaired or replaced. Always leave guard in
operating position when using the saw.
DANGER:
When sawing through work, lower blade guard does
not cover blade on the underside of work. Since
blade is exposed on underside of work, keep hands
and fingers away from cutting area. Any part of your
body coming in contact with moving blade will result
in serious injury.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KICKBACK
See Figures 5, 6, 7, and 8.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood. See Figure 5.
DANGER:
Release switch immediately if blade binds or saw
stalls. Kickback could cause you to lose control of
the saw. Loss of control can lead to serious injury.
Fig. 5
To guard against kickback, avoid dangerous practices such
as the following.
Setting blade depth incorrectly.
Sawing into knots or nails in workpiece.
Twisting the blade while making a cut.
Making a cut with a dull, gummed up, or improperly set
blade.
Supporting the workpiece incorrectly.
Forcing a cut.
Cutting warped or wet lumber.
Operating the tool incorrectly or misusing the tool.
To lessen the chance of kickback, follow these safety prac-
tices.
Fig. 6
Do not cut warped or wet lumber.
Keep the blade at the correct depth setting. The depth
setting should not exceed 1/4 in. below the material being
cut.
Inspect the workpiece for knots or nails before cutting.
Never saw into a knot or nail.
Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
Use clean, sharp, and properly set blades. Never make
cuts with dull blades.
Support the workpiece properly before beginning a cut.
Fig. 7
Use steady, even pressure when making a cut. Never
force a cut.
Hold the saw firmly with both hands and keep your body
in a balanced position so as to resist the forces if kickback
should occur.
WARNING:
When using the saw, always stay alert and exercise
control. Do not remove the saw from the workpiece
while the blade is moving.
Fig. 8
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING/STOPPING THE SAW
SWITCH
TRIGGER
See Figure 9.
To start the saw: Depress the switch trigger.
Always let the blade reach full speed, then guide the saw
into the workpiece.
WARNING:
The blade coming in contact with the workpiece
before it reaches full speed could cause the saw to
“kickback” towards you resulting in serious injury.
To stop the saw: Release the switch trigger.
After you release the switch trigger, allow the blade to
come to a complete stop. Do not remove the saw from the
workpiece while the blade is moving.
ADJUSTING BLADE DEPTH
See Figure 10.
Fig. 9
Always keep correct blade depth setting. The correct blade
depth setting for all cuts should not exceed 1/4 in. below
the material being cut. More blade depth will increase the
chance of kickback and cause the cut to be rough. For more
depth of cut accuracy, a scale is located on the elevation
bracket.
ELEVATION
BRACKET
DEPTH
ADJUSTMENT
LEVER
NOTE: The marks on the scale refer to the actual depth of
cut (blade exposure).
Unplug the saw.
Pull depth adjustment lever upward to release. The depth
adjustment lever is located between the guard and handle
of the saw.
Determine the desired depth of cut.
To select the depth of cut, hold base flat against the
workpiece. Raise or lower saw to align the desired mea-
surement on the scale with the lock washer indicator
located directly above the lock mechanism.
Push down on the depth adjustment lever to lock the
lever in place and secure the position.
Fig. 10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING THE SAW
See Figures 11, 12, and 13.
It is important to understand the correct method for operat-
ing the saw. Refer to the figures in this section to learn the
correct and incorrect ways for handling the saw.
WARNING:
To make sawing easier and safer, always maintain
proper control of the saw. Loss of control could
cause an accident resulting in possible serious
injury.
DANGER:
Fig. 11
When lifting the saw from the workpiece, the blade
is exposed on the underside of the saw until the
lower blade guard closes. Make sure the lower blade
guard is closed before setting the saw down.
To make the best possible cut, follow these helpful hints.
Hold the saw firmly with both hands.
Avoid placing your hand on the workpiece while making
a cut.
LINE OF
CUT
Support the workpiece so that the cut is always on your
right.
Support the workpiece near the cut.
Clamp the workpiece securely so that the workpiece will
not move during the cut.
Avoid placing the saw on the part of the workpiece that
will fall off when the cut is made.
Fig. 12
Place the workpiece with the “good” side down.
Draw a guideline along the desired line of cut before
beginning the cut.
Keep the cord away from the cutting area. Always place
the cord to prevent it from hanging up on the workpiece
while making a cut.
DANGER:
If the cord hangs up on the workpiece during a cut,
release the switch trigger immediately. Unplug the
saw and reposition the cord to prevent it from hang-
ing up again.
DANGER:
Using a saw with a damaged cord could result in
serious injury or death. If the cord has been dam-
aged, have it replaced before using the saw again.
Fig. 13
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CROSS CUTTING
See Figure 14.
When making a cross cut, align the line of cut with the full
length kerf indicator on the base.
Since blade thicknesses vary, always make a trial cut in scrap
material along a guideline to determine how much, if any, you
must offset the guideline to produce an accurate cut.
NOTE: The distance from the line of cut to the guideline is
the amount you should offset the guide.
BEVEL CUTTING
The base of the saw may be adjusted for bevel cuts up to
51.5°.
FULL LENGTH
KERF INDICATOR
WARNING:
The tool should never be connected to a power
supply when you are assembling parts, making
adjustments, cleaning, performing maintenance,
or when the tool is not in use. Disconnecting the
tool will prevent accidental starting that could cause
serious injury.
Fig. 14
LINE OF CUT
BLADE
0° BEVEL STOP
The saw has a positive 0° bevel stop that has been factory
adjusted to assure 0° angle of the saw blade when making
90° cuts.
TO CHECK 0° BEVEL STOP
See Figure 15.
Unplug the saw.
COMBINATION
SQUARE
Place the saw in an upside down position on a work-
bench.
Fig. 15
Move the lower blade guard out of the way so that the
saw blade is exposed.
Check the squareness of the saw blade to the base of
the saw using a carpenter’s square.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST 0° BEVEL STOP
See Figures 16 and 17.
BEVEL
ADJUSTMENT
LEVER
Unplug the saw.
Pull bevel adjustment lever upward to release.
Turn set screw with hex wrench and adjust base until it
is square with the saw blade.
Securely lock the bevel adjustment lever.
TO ADJUST BEVEL SETTING
See Figure 16.
Unplug the saw.
Pull the bevel adjustment lever upward until the motor
housing moves freely.
Raise the motor housing end of the saw until you reach
the desired angle setting on the bevel scale (0-45°).
51.5° BEVEL
BUTTON
NOTE: Pull the adjustment lever all the way up to set the
angle at 51.5°. To reach the 51.5° bevel setting, push
the 51.5° bevel button.
Fig. 16
Press downward on the bevel adjustment lever until the
motor housing is securely locked in place.
SET
SCREW
Fig. 17
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO BEVEL CUT
See Figure 18.
WARNING:
Attempting a bevel cut without having the bevel
adjustment lever securely locked in place can result
in serious injury.
Hold the saw firmly with both hands as shown.
Rest the front edge of the base on the workpiece.
Start the saw and let the blade reach full speed.
Guide the saw into the workpiece and make the cut.
Release the trigger and allow the blade to come to a
complete stop.
Lift the saw from the workpiece.
The notch marked 0° in the base may be used as a guide
for making straight 90° cuts. For 45° bevel cuts, the notch
marked 45° may be used as a guide.
45°
NOTCH
90°
NOTCH
POCKET CUTTING
See Figure 19.
Fig. 18
WARNING:
Always adjust bevel setting to zero before making
a pocket cut. Attempting a pocket cut at any other
setting can result in loss of control of the saw pos-
sibly causing serious injury.
LOWER
BLADE GUARD
Adjust the bevel setting to zero.
Set the blade to the correct blade depth setting, depend-
ing on the material to be cut.
Swing the lower blade guard up using the lower blade
guard handle.
NOTE: Always raise the lower blade guard with the handle
to avoid serious injury.
Hold the lower blade guard by the handle.
Rest the front of the base flat against the workpiece with
the rear of the handle raised so the blade does not touch
the workpiece.
Start the saw and let the blade reach full speed.
Fig. 19
Guide the saw into the workpiece and make the cut.
Release the trigger and allow the blade to come to a
complete stop.
WARNING:
Lift the saw from the workpiece.
Always cut in a forward direction when pocket cut-
ting. Cutting in the reverse direction could cause
the saw to climb up on the workpiece and back
toward you.
Clear corners out with a hand saw or sabre saw.
WARNING:
Never tie the lower blade guard in a raised position.
Leaving the blade exposed could lead to serious
injury.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LENGTH OF CUT
SCALE
LENGTH OF CUT SCALE
See Figure 20.
The saw is equipped with a length of cut scale on its base. It
is parallel with the saw blade and you can use it to measure
the distance the blade cuts into the material.
NOTE: Six inches is the maximum length of cut that you can
measure. Also, it is accurate only when the depth of cut is
set at full maximum depth.
Fig. 20
ADJUSTMENTS
ADJUSTING THE LEVER LOCK MECHANISM
See Figure 21.
The lever lock mechanism located at the bevel bracket and
at the base of the elevation bracket may be adjusted to the
degree of leverage the operator prefers.
Pull the lever upward until it is fully loosened.
Gently pry the retaining clip from the cap nut with a small
flat blade screwdriver. Save the retaining clip.
Pull the lever off the cap nut and adjust the lever loca-
tion.
Tighten the lever to check for desired tightness.
Fig. 21
If this is the desired tightness, then reinstall the retaining
clip on the cap nut, using a flat blade screwdriver to tap
it into place.
NOTE: Reinstall the retaining clip with the bow up.
If the lever is not tight enough, repeat the above steps.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Electric tools used on fiberglass material, wallboard, spack-
ling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes, com-
mutators, etc. Consequently, we do not recommended using
this tool for extended work on these types of materials. How-
ever, if you do work with any of these materials, it is extremely
important to clean the tool using compressed air.
WARNING:
When servicing use only identical RIDGID® replace-
ment parts. Use of any other parts may create a
hazard or cause product damage.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING:
WARNING:
The tool should never be connected to a power
supply when you are assembling parts, making
adjustments, cleaning, performing maintenance,
or when the tool is not in use. Disconnecting the
tool will prevent accidental starting that could cause
serious injury.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a dust
mask.
GENERAL
Use clean cloths to remove dirt, carbon dust, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc. come in
contact with plastic parts. They contain chemicals
that can damage, weaken, or destroy plastic.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LUBRICATION
See Figure 22.
This tool has been properly lubricated and is ready to use.
It is recommended that the gears be lubricated only with
Mobil SHC 636 Oil.
After extended use, check the oil level, using the dipstick
provided.
DIPSTICK
CHECKING THE OIL
Unplug the tool.
Place the base of the saw on a horizontal surface.
Remove the oil plug using a 6mm hex wrench.
Insert the dipstick straight into the tool. Do not force.
Check the oil level. It should be between the two white
marks on the dipstick.
If the oil level is not above the first white mark, add oil a
little at a time until the oil reaches the correct level.
Return the dipstick to the storage area on the underside
of the tool.
CHANGING THE OIL
Unplug the tool.
OIL PLUG
Place the base of the saw on a horizontal surface.
Remove the oil plug using a 6mm hex wrench.
Fig. 22
Tip the saw up and let oil drain out into an appropriate
oil container.
Replace the oil using a small funnel (less than 1/4 in.
spout). Take care to let air out while putting new oil in to
avoid spilling. Fill only with .5 oz. (15cc, or one tablespoon)
Mobil SHC 636 Oil.
Fill the gear case until the oil level is between the two
marks on the dipstick. Do not overfill. If the level of oil
raises above the second mark on the dipstick while the
base is on a level surface, overheating may occur.
Replace the oil plug with a 6mm hex wrench. Do not
overtighten. The O-ring under the head should be com-
pressed slightly. Overtightening will cause the o-ring to
unseat and not seal properly.
NOTE: With a new saw, change the oil following the first
ten hours of use. This will prolong the life of the tool by
removing the gear particles from the oil when the gears
are breaking in.
BRUSH REPLACEMENT
BRUSH
ASSEMBLY
See Figure 23.
The tool has externally accessible brush assemblies that
should be periodically checked for wear.
BRUSH
CAP
SCREWS
Unplug the tool.
Fig. 23
Remove the brush cap with a torx screwdriver. The brush
assembly is spring loaded and will pop out when you
remove the brush cap.
Remove the brush assembly (brush and spring).
Check for wear. If worn, always replace in pairs. Do not
replace one side without replacing the other.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
24
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
7-1/4 WORM DRIVE SAW
DOUBLE INSULATED
R3210-1
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R3210-1
Model No.
Serial No.
983000-991
5-16-06 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|