OPERATOR’S MANUAL
12 in. SLIDING COMPOUND MITER
SAW WITH LASER
Double Insulated
MS1290LZA
®
Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
SECUREWORK.Useclampsoravisetoholdworkwhen
practical, it is safer than using your hand and frees both
hands to operate the tool.
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, could result in
electric shock, fire and/or serious personal injury.
DONOTOVERREACH.Keepproperfootingandbalance
at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instruc-
tions for lubricating and changing accessories.
READ ALL INSTRUCTIONS
KNOWYOURPOWERTOOL.Readtheoperator’smanual
carefully. Learn the applications and limitations as well
as the specific potential hazards related to this tool.
DISCONNECTTOOLS.Whennotinuse,beforeservicing,
orwhenchangingattachments,blades,bits,cutters,etc.,
all tools should be disconnected from power source.
GUARDAGAINSTELECTRICALSHOCKBYPREVENT-
ING BODY CONTACT WITH GROUNDED SURFACES.
For example: pipes, radiators, ranges, refrigerator enclo-
sures.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may result in injury.
KEEP GUARDS IN PLACE and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habitofcheckingtoseethatkeysandadjustingwrenches
are removed from tool before turning it on.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped.
KEEPWORKAREACLEAN.Clutteredareasandbenches
invite accidents. DO NOT leave tools or pieces of wood
on the tool while it is in operation.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefullycheckedtodeterminethatitwilloperateproperly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe dis-
tance from work area. Do not let visitors contact tool or
extension cord while operating.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade, cutter, or sanding spindle against the direction
or rotation of the blade, cutter, or sanding spindle only.
MAKE WORKSHOP CHILDPROOF with padlocks,
master switches, or by removing starter keys.
NEVERLEAVETOOLRUNNINGUNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
DON’T FORCE THE TOOL. It will do the job better and
safer at the feed rate for which it was designed.
USE THE RIGHT TOOL. Do not force the tool or attach-
PROTECT YOUR LUNGS. Wear a face or dust mask if
ment to do a job for which it was not designed.
the cutting operation is dusty.
USETHEPROPEREXTENSIONCORD. Makesureyour
extensioncordisingoodcondition.Useonlyacordheavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 14 is recommended for an extension
cord 25 feet or less in length. If in doubt, use the next
heaviergauge.Thesmallerthegaugenumber,theheavier
the cord.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never carry tool by the cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
USE OUTDOOR EXTENSION CORDS. When tool is
used outdoors, use only extension cords with approved
ground connection that are intended for use outdoors
and so marked.
DRESSPROPERLY.Donotwearlooseclothing,neckties,
or jewelry that can get caught and draw you into moving
parts. Rubber gloves and nonskid footwear are recom-
mended when working outdoors. Also wear protective
hair covering to contain long hair.
KEEPBLADESCLEAN,SHARP,ANDWITHSUFFICIENT
SET. Sharp blades minimize stalling and kickback.
BLADE COASTS AFTER BEING TURNED OFF.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
NEVERUSEINANEXPLOSIVEATMOSPHERE.Normal
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at an
authorized service facility. The conductor with insulation
havinganoutersurfacethatisgreenwithorwithoutyellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of the saw is 12 in.
BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
NEVER TOUCH BLADE or other moving parts during
INSPECT EXTENSION CORDS PERIODICALLY and
use.
replace if damaged.
POLARIZEDPLUGS.Toreducetheriskofelectricshock, NEVER START A TOOL WHEN ANY ROTATING
this tool has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any
way.
COMPONENTISINCONTACTWITHTHEWORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHENSERVICINGuseonlyidenticalreplacementparts.
Use of any other parts may create a hazard or cause
product damage.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
SPECIFIC SAFETY RULES
FIRMLY CLAMP OR BOLT the tool to a workbench or USE THIS SAW TO CUT WOOD, WOOD PRODUCTS,
table at approximately hip height.
AND SOME PLASTICS ONLY. DO NOT CUT METALS,
CERAMICS OR MASONRY PRODUCTS.
KEEP HANDS AWAY FROM CUTTING AREA. Do not
reach underneath work or in blade cutting path with your
handsandfingersforanyreason.Alwaysturnthepoweroff.
BEFORE MOVING THE SAW, unplug the saw then lock
the miter, bevel, slide, and power head positions.
ALWAYSSUPPORTLONGWORKPIECESwhilecutting
tominimizeriskofbladepinchingandkickback. Sawmay
slip, walk, or slide while cutting long or heavy boards.
NEVER USE A LENGTH STOP ON THE FREE SCRAP
END OF A CLAMPED WORKPIECE. NEVER hold onto
or bind the free scrap end of the workpiece in any opera-
tion. If a work clamp and length stop are used together,
they must both be installed on the same side of the saw
table to prevent the saw from catching the loose end and
kicking up.
ALWAYS USE A CLAMP to secure the workpiece when
possible.
BESURETHEBLADECLEARSTHEWORKPIECE.Never
startthesawwiththebladetouchingtheworkpiece.Allow
motor to come up to full speed before starting cut.
NEVER cut more than one piece at a time. DO NOT
STACK more than one workpiece on the saw table at a
time.
MAKESURETHEMITERTABLEANDSAWARMBEVEL
FUNCTION) ARE LOCKED IN POSITION BEFORE
OPERATINGYOURSAW.Lockthemitertablebysecurely
tightening the miter lock lever. Lock the saw arm (bevel
function) by securely tightening the bevel lock lever.
NEVER PERFORM ANY OPERATION FREEHAND.
Always place the workpiece to be cut on the miter table
and position it firmly against the fence as a backstop.
Always use the fence.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
NEVER hand hold a workpiece that is too small to be
MAKE SURE WORK AREA HAS AMPLE LIGHTING to
see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using your
saw.
clamped. Keep hands clear of the cutting area.
NEVER reach behind, under, or within three inches of the
blade and its cutting path with your hands and fingers for
any reason.
ALWAYS TURN OFF THE SAW before disconnecting it
to avoid accidental starting when reconnecting to power
supply.NEVERleavethesawunattendedwhileconnected
to a power source.
NEVER reach to pick up a workpiece, a piece of scrap,
or anything else that is in or near the cutting path of the
blade.
THIS TOOL has the following markings:
AVOID AWKWARD OPERATIONS AND HAND POSI-
TIONS where a sudden slip could cause your hand to
move into the blade. ALWAYS make sure you have good
balance. NEVER operate the miter saw on the floor or in
a crouched position.
a) Wear eye protection.
b) Keep hands out of path of saw blade
c) Do not operate saw without guards in place.
d) Do not perform any operation freehand.
e) Never reach around saw blade.
f) Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
g) Disconnect power (or unplug tool as applicable)
before changing blade or servicing.
NEVER stand or have any part of your body in line with
the path of the saw blade.
ALWAYSreleasethepowerswitchandallowthesawblade
to stop rotating before raising it out of the workpiece.
DO NOT TURN THE MOTOR SWITCH ON AND OFF
RAPIDLY. This could cause the saw blade to loosen and
could create a hazard. Should this ever occur, stand clear
and allow the saw blade to come to a complete stop.
Disconnect the saw from the power supply and securely
retighten the blade bolt.
h) No load speed.
ALWAYS MAKE SURE THE SAW BLADE HAS CLEAR-
ANCE OF ALL OBSTRUCTIONS BEFORE TURNING
THE SAW ON.
MAKE SLIDING CUTS by pushing the saw blade down
on top of the workpiece then sliding it back toward the
rear of the saw. DO NOT pull the saw toward you while
making a cut.
IF ANY PART OF THIS MITER SAW IS MISSING or
should break, bend, or fail in any way, or should any
electrical component fail to perform properly, shut off
the power switch, remove the miter saw plug from the
powersourceandhavedamaged, missing, orfailedparts
replaced before resuming operation.
ALWAYS carry the tool only by the carrying handles.
AVOID direct eye exposure when using the laser guide.
THIS SAW CAN TIP OVER if the saw head is released
suddenly and the saw is not secured to a work surface.
ALWAYS secure this saw to a stable work surface before
any use to avoid serious personal injury.
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
ALWAYS STAY ALERT! Do not allow familiarity (gained
from frequent use of your saw) to cause a careless
mistake. ALWAYS REMEMBER that a careless fraction
of a second is sufficient to inflict severe injury.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Type of current
Alternating Current
Direct Current
Type or a characteristic of current
n
o
No Load Speed
Class II Construction
Per Minute
Rotational speed, at no load
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
To reduce the risk of injury or damage, avoid contact with any
hot surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to
use this product until you read thoroughly and un-
derstand completely the operator’s manual. If you
do not understand the warnings and instructions in
the operator’s manual, do not use this product. Call
RIDGID® customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety
glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask
for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which
is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protect-
ing insulation. Double insulated tools do not need to be
grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
The double insulated system is intended to protect
the user from shock resulting from a break in the
tool’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
**Ampere rating (on product data plate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
ELECTRICAL CONNECTION
100'
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If the tool does
not operate when plugged into an outlet, double-check the
power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If dam-
aged replace immediately. Never use tool with a
damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Non-Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Push Blocks (for jointer planers)
Arbor
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator's hands well away from the cutterhead.
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Push Blocks and Push Sticks (for table saws)
Devices used to feed the workpiece through the saw blade
during cutting operations. A push stick (not a push block)
should be used for narrow ripping operations. These aids
help keep the operator's hands well away from the blade.
Chamfer
A cut removing a wedge from a block so the end (or part of
the end) is angled rather than at 90°.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide for
drilling large holes accurately.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
Resaw
A cutting or shaping operation made across the grain or the
width of the workpiece.
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Cutter Head (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Ripping or Rip Cut
Featherboard
A cutting operation along the length of the workpiece.
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Set
The distance that the tip of the saw blade tooth is bent (or
Gum
set) outward from the face of the blade.
A sticky, sap-based residue from wood products.
Snipe (planers)
Heel
Depression made at either end of a workpiece by cutter
Alignment of the blade to the fence.
blades when the workpiece is not properly supported.
Kerf
The material removed by the blade in a through cut or the
Through Sawing
slot produced by the blade in a non-through or partial cut.
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Kickback
A hazard that can occur when the blade binds or stalls,
Throw-Back
throwing the workpiece back toward operator.
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
Leading End
The end of the workpiece pushed into the tool first.
Workpiece or Material
The item on which the operation is being done.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Cutting Capacity with Miter at 0°/Bevel 0°:
Maximum nominal lumber sizes:....................2 x 12, 4 x 4
Blade Diameter.......................................................... 12 in.
Arbor Hole ....................................................................1 in.
No Load Speed .....................................4,000 r/min. (RPM)
Input ................................ 120 V, 60 Hz, AC Only, 15 Amps
Net Weight................................................................70 lbs.
Cutting Capacity with Miter at 45°/Bevel 0°:
Maximum nominal lumber sizes:..............................2 x 10
Cutting Capacity with Miter at 0°/Bevel 45°:
Maximum nominal lumber sizes:..............................2 x 12
DEPTH CONTROL KNOB
CORD STORAGE
SWITCH
LOCK
SLIDE
LOCK KNOB
“D” HANDLE
CARRYING
HANDLE
UPPER BLADE
GUARD
SWITCH
TRIGGER
BLADE WRENCH
DUST
BAG
STORAGE
®
BEVEL
LOCK
LEVER
LOWER BLADE
GUARD
SLIDE BAR
BEVEL
STOP PIN
ZERO CLEARANCE
THROAT PLATE
SLIDING MITER
FENCE
MITER
THUMBWHEEL
FENCE
SCREW
WORK
CLAMP
MITER LOCK
LEVER
FRONT
CARRYING HANDLE
MITER
TABLE
MITER
SCALE
SAW BASE
Fig. 1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
ELECTRIC BRAKE
An electric brake quickly stops blade rotation after the switch
trigger is released.
KNOW YOUR COMPOUND MITER SAW
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
LASER GUIDE
For more accurate cuts, a laser guide is included with your
miter saw. When used properly, the laser guide makes
accurate, precision cutting simple and easy.
12 IN. BLADE
CARRYING
LOCK
A 12 in. blade is included with your compound miter saw. It
will cut materials up to 13-1/2 in. wide, depending upon the
angle at which the cut is being made.
HANDLE
PIN
15 AMP MOTOR
This saw has a powerful 15 amp motor with sufficient
power to handle tough cutting jobs. It is made with all ball
bearings, and has externally accessible brushes for ease
of servicing.
BEVEL LOCK LEVER
The bevel lock lever securely locks your compound miter
saw at desired bevel angles. Pulling the lever forward will
release the saw allowing the blade to be tilted either left
or right for bevel cuts. Pushing the lever back will lock the
saw in place.
DEPTH
GUIDE
BEVEL STOP PIN
The bevel stop pin has two positions:
FRONT
CARRYING
HANDLE
1. Override (pin pulled completely out)
2. The 0° - 48° position for crown molding (pin pushed in)
SAW ARM LOCKED IN DOWN POSITION
CARRYING HANDLES
See Figure 2.
Fig. 2
Carrying handles are located on the top of the saw arm and
on the front of the saw base.
SWITCH
TRIGGER
To transport: turn off and unplug the saw; lower saw arm
and lock it in the down position; lock bevel and miter lock
levers; lock slide lock knob.
SPINDLE
LOCK BUTTON
DEPTH CONTROL KNOB
When loosened, the depth control knob allows the user to
adjust the depth guide then holds the guide securely in place
when the knob is retightened.
NOTE: It is not necessary to loosen the knob when locking
or unlocking the saw arm.
DEPTH GUIDE
See Figure 2.
The depth guide is used for locking the saw arm in the down
position or as a guide for limiting downward movement of
the saw arm.
NOTE: Controlling depth of cut is necessary when rough
cutting a dado.
Fig. 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
MITER LOCK LEVER
The miter lock lever securely locks the saw at the desired
miter angle.
SPINDLE LOCK BUTTON
See Figure 3.
A spindle lock button has been provided for locking the
spindle (keeping the saw blade from turning). Depress
and hold the lock button only while installing, changing, or
removing the saw blade.
MITER SCALE
The miter scale has index points provided at 0°, 15°, 22.5°,
31.6°, 45°, and 60.°
SWITCH TRIGGER
See Figure 4.
MITER THUMBWHEEL
The saw will not start until you depress the switch lock with
your thumb then squeeze the switch trigger. To prevent
unauthorized use of the compound miter saw, disconnect
it from the power supply and lock the switch in the OFF
position. To lock the switch, install a padlock (not included)
through the hole in the switch trigger. A lock with a long
shackle up to 9/32 in. diameter may be used. When the lock
is installed and locked, the switch is inoperable. Store the
padlock key in another location.
The miter thumbwheel, when used with the miter lock lever
lifted (unlocked), can release the miter table from pre-set
index points. With the thumbwheel spun down (and
released), the miter table moves freely to any desired angle.
With thumb on thumbwheel, push down and hold to over-
ride (bypass) index points; release thumbwheel when close
to desired point and move the lock lever into place with a
click. With the thumbwheel spun up, the miter table will stop
at each index point on the miter scale.
REPEAT-A-CUT™
See Figure 5.
SWITCH LOCK
The Repeat-A-Cut™ feature on both the left and right side
miter fences can be used when making repetitive cuts.
Simply mark the fence with a pencil, make the desired
number of cut(s), then wipe the mark off with a soft cloth.
PADLOCK
SELF-RETRACTING LOWER BLADE GUARD
SWITCH
The lower blade guard is made of shock-resistant, see-
through plastic that provides protection from each side of
the blade. It retracts over the upper blade guard as the saw
is lowered into the workpiece.
TRIGGER
Fig. 4
SLIDE BAR
When unlocked, the saw arm will glide forward and back-
ward the length of the slide bar for cutting various workpiece
widths.
®
REPEAT-A-CUT
SLIDE LOCK KNOB
The slide lock knob locks and unlocks the sliding feature
of this tool.
SLIDING MITER FENCES
The sliding miter fences provided with this saw help hold
the workpiece securely when making most cuts. The sliding
feature allows for clearance of the saw blade when making
bevel or compound cuts. Some cuts may require that the
sliding fence be removed completely to avoid interference
between the fence and the blade.
SLIDE
BAR
Loosen the fence screw before attempting to slide the fences
or lift them for removal. Once the desired position of the
fence is determined, retighten the fence screw securely.
SLIDING
MITER FENCE
Fig. 5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS NEEDED
The following tools (not included) are needed for making adjustments or installing the blade:
RATCHET
COMBINATION WRENCH, 12 mm
SOCKET, 19 mm
PHILLIPS SCREWDRIVER
COMBINATION SQUARE
FRAMING SQUARE
Fig. 6
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with your miter saw:
Dust Bag
Blade Wrench
Dust Bag Frame
Dust Guide
Work Clamp
Hex Key, 1/16 in.
Laser Guide
Flat Head Socket Cap Screw
Operator’s Manual (not shown)
DUST BAG
WORK CLAMP
HEX KEY,
1/16 in.
DUST BAG
FRAME
LASER
GUIDE
BLADE
WRENCH
FLAT HEAD
SOCKET CAP
SCREW
DUST
GUIDE
Fig. 7
WARNING:
The use of attachments or accessories not listed in this manual might be hazardous and could cause serious
personal injury.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product requires assembly.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in acciden-
tal starting and possible serious personal injury.
Carefully lift saw from the carton by the carrying handle
and the saw base, and place it on a level work surface.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
This saw has been shipped with the saw arm secured in
the down position. To release the saw arm, push down
on the top of the saw arm, cut the tie-wrap, and pull out
on the depth guide.
Lift the saw arm by the handle. Hand pressure should
remain on the saw arm to prevent sudden rise upon
release of the tie wrap and/or depth guide.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
WARNING:
Do not start the miter saw without checking for
interference between the saw blade and the sliding
miter fences. Damage could result to the blade if
it strikes the miter fence during operation of the
saw.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
influenced the settings, refer to specific procedures ex-
plained in this manual.
WARNING:
Always make sure the compound miter saw is
securely mounted to a workbench or an approved
workstand. Failure to heed this warning can result
in serious personal injury.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
MOUNTING HOLES
See Figure 8.
The compound miter saw should be mounted to a firm
supporting surface such as a workbench, mounting board,
or leg stand. The saw base has eight mounting holes: four
large bolt holes (B) and four small screw holes (A). If using
bolts, they should be of sufficient length to accommodate
the saw base, lock washers, hex nuts, and the thickness of
the workbench or other mounting surface. Tighten all four
bolts or screws securely. Do not use screws if mounting to
a leg stand.
WARNING:
If any parts are damaged or missing, do not oper-
ate this tool until the missing parts are replaced.
Failure to heed this warning could result in serious
personal injury.
WARNING:
The hole pattern for mounting to a workbench is shown in
figure 8. Carefully check the workbench after mounting to
make sure that no movement can occur during use. If any
tipping, sliding, or walking is noted, secure the workbench
to the floor before operating.
Do not attempt to modify this tool or create acces-
sories not recommended for use with this tool. Any
such alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious personal injury.
B
A
A
B
TRACE HOLES AT THESE
LOCATIONS FOR HOLE PATTERN
(A - SCREWS AND B - BOLTS)
A
B
A
B
MOUNTING
SURFACE
SAW BASE
Fig. 8
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Many of the illustrations in this manual show only
portions of the compound miter saw. This is intentional
so that we can clearly show points being made in the
illustrations. Never operate the saw without all guards
securely in place and in good operating condition.
DEPTH CONTROL
KNOB
SAW ARM
DEPTH
GUIDE
LOCKING / UNLOCKING THE SAW ARM
See Figure 9.
When locking and unlocking the saw arm, it is not necessary
to loosen the depth control knob.
To unlock and raise the saw arm:
Firmly grasp the “D” handle and apply downward pres-
sure while at the same time pulling the depth guide out
and away from the saw housing.
Turn the guide to the right until the flat of the guide is
facing up.
Release the guide and slowly raise the saw arm.
To relock the saw arm:
Firmlygraspthe“D”handleandapplydownwardpressure
while at the same time pulling the depth guide out and
away from the saw housing.
Fig. 9
Turn the guide to the left until the hole in the guide is
positioned over the lock pin.
DEPTH CONTROL
KNOB
LOCK PIN
Release the guide allowing the lock pin to align with the
hole in the guide.
Check that the slide lock knob is locked in place by
DEPTH
GUIDE
turning the knob clockwise.
USING THE DEPTH GUIDE
See Figure 10.
When used, the depth guide limits the downward travel of the
blade when cutting dadoes and other non-through cuts.
Make a mark on the lock pin with a pencil for use with the
scale on the guide. “A” on the guide represents the saw
blade teeth being level with the miter table. Each mark on
the depth guide is approximately 1/4 in. Always make a
practice cut on scrap wood. With the flat side of the guide
facing up, the saw can be used without any interference
from the guide.
To use the depth guide:
If the saw is in storage or transport position, unlock the
saw arm.
Position the depth guide by turning until it engages the
internal locking mechanism.
Loosen the depth control knob (turn knob counter-
clockwise).
Fig. 10
Determine the desired depth of cut, set the guide to that
mark, and retighten the depth control knob (turn knob
clockwise).
NOTE: To override the depth setting, pull the depth gauge
out and away from the saw housing and turn the guide until
the flat of the guide is facing up.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALLING THE DUST BAG
See Figure 11.
Squeeze the metal clips on the dust bag, then slide the
metal ring over the end of the dust guide. Position the
metal ring so it is between the two molded rings on the
dust guide. Release the dust bag clips.
DUST BAG FRAME
Snap the frame onto the slide bar by squeezing the dust
bag frame, then pushing it down over the slide bar.
Insert the dust guide inside the exhaust port in the upper
blade guard.
Slip the dust bag over the frame with the zipper facing
down.
NOTE: For efficient operation, empty the dust bag before it
is half full. This will permit better air flow through the bag.
DUST BAG FRAME
INSTALLING THE WORK CLAMP
See Figure 12.
WARNING:
In some operations, the work clamp assembly
may interfere with the operation of the blade guard
assembly. Always make sure there is no interfer-
ence with the blade guard prior to beginning any
cutting operation to reduce the risk of serious
personal injury.
DUST
GUIDE
EXHAUST
PORT
The work clamp provides greater control by clamping the
workpiece to the miter table. It also helps to prevent the
workpiece from creeping toward the saw blade. This is very
helpful when cutting compound miters. Depending on the
cutting operation and the size of the workpiece, it may be
necessary to use a C-clamp instead of the work clamp to
secure the workpiece prior to making the cut. The work clamp
can be installed and used on either side of the blade.
DUST BAG
To install the work clamp:
Place the work clamp shaft in one of the holes located
behind the sliding miter fence.
NOTE: Align the pin on the work clamp shaft with the slot
Fig. 11
in the hole.
WORK CLAMP
SHAFT
Rotate the knob on the work clamp to move it up or down
WORK CLAMP
as needed.
NOTE: The work clamp has a quick release lever that
makes positioning of the work clamp effortless. Push the
button on the side of the work clamp to quickly release the
workpiece.
QUICK
RELEASE
LEVER
Fig. 12
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
LASER GUIDE
OR OUTER
BLADE WASHER
WARNING:
Make sure the spindle lock button is not engaged
before reconnecting saw to power source. Never
engage spindle lock button when blade is rotating.
SCREW
BLADE
BOLT
BLADE
INSTALLING / REPLACING THE BLADE
See Figure 13.
INNER BLADE
WASHER
LOWER
BLADE
GUARD
WARNING:
SCREW
A 12 in. blade is the maximum blade capacity of
the saw. Never use a blade that is too thick to allow
outer blade washer to engage with the flats on the
spindle. Larger blades will come in contact with the
blade guards, while thicker blades will prevent the
hex bolt from securing the blade on the spindle.
Either of these situations could result in a serious
accident and can cause serious personal injury.
BLADE
BOLT
COVER
BLADE
LASER
GUIDE
Unplug the saw.
TO
LOOSEN
Raise saw arm.
Rotate lower blade guard up and loosen screw. Rotate
blade bolt cover up and back to expose the hex bolt.
Depress the spindle lock button and rotate the hex bolt
TO
TIGHTEN
until the spindle locks.
Using the wrench provided, loosen and remove the hex
bolt.
NOTE: The hex bolt has left hand threads. Turn hex bolt
clockwise to loosen.
HEX
BOLT
INNER BLADE
FLAT
ON SPINDLE
WASHER WITH
Remove the washer, outer blade washer (or laser guide),
DOUBLE “D” FLATS
and the blade. Do not remove the inner blade washer.
Fig. 13
Wipe a drop of oil onto the inner blade washer and the
outer blade washer (or laser guide) where they contact
the blade.
CAUTION:
Always install the blade with the blade teeth and
the arrow printed on the side of the blade pointing
down at the front of the saw. The direction of blade
rotation is also stamped with an arrow on the upper
blade guard.
WARNING:
If inner blade washer has been removed, replace
it before placing blade on spindle. Failure to do
so could cause an accident since blade will not
tighten properly.
Replace outer blade washer (or laser guide). The double
“D” flats on the blade washers align with the flats on the
spindle.
Fit saw blade inside lower blade guard and onto spindle.
The blade teeth point downward at the front of saw as
shown in figure 13.
Depress spindle lock button and replace the washer and
hex bolt.
NOTE: The hex bolt has left hand threads. Turn blade
bolt counterclockwise to tighten.
Tighten hex bolt securely.
Replace the lower blade guard and blade bolt cover.
Retighten the screw securely.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
DANGER:
Laser radiation. Avoid direct eye contact with light
source.
®
ALIGNING THE LASER GUIDE LINE
See Figure 14.
The laser guide will generate a laser line on the work surface
when the saw blade is spinning. The laser line will appear as
a broken line on the workpiece when the blade assembly is
in the uppermost position and the motor switch is activated.
This broken line will let you see your mark and your laser
guide line at the same time, and will assist you in lining up
your mark for more accurate cutting of the workpiece.
BROKEN
LINE
Align the laser line and your mark with the blade at the
uppermostposition. Once bothlines are in alignment, donot
move the workpiece until after you have finished cutting.
As the blade assembly is lowered toward the workpiece, the
broken line will become solid.
Follow the directions below for using the laser guide:
Fig. 14
Removing the Mark:
Position the laser line on the left edge of your mark on the
work surface in order to remove the mark.
To Cut the Mark:
Position the laser line near or over your mark on the work
surface in order to cut the mark.
To Leave the Mark:
Position the laser line near the right edge of your mark on
the work surface in order to leave the mark.
After you have become familiar with using the laser guide,
you will be able to remove, cut, or leave your mark on the
work surface. Practice will teach you the correct position for
aligning the laser line with your mark. To adjust the position of
the laser line, see the Adjustments section of this manual.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
REMOVING / REPLACING THE ZERO CLEAR-
ANCE THROAT PLATE
See Figure 15.
®
When squaring the saw blade, it may be necessary to
move the throat plate away from the blade. Once the saw’s
alignment has been confirmed, return the throat plate to its
original position. Never operate the saw without a throat
plate installed.
Unplug the saw.
Using the blade wrench provided, loosen the screws
securing the right side of the zero clearance throat
plate.
BLADE
WRENCH
Slide the throat plate away from the blade as far as
possible.
Retighten the screws, being careful not to overtighten
which can cause the throat plate to bow or bend.
Repeat the above steps for the left side of the throat
plate.
CENTERING THE SAW BLADE BETWEEN THE
SLIDE BARS
See Figure 16.
ZERO CLEARANCE
THROAT PLATE
Fig. 15
The saw blade should be centered (approximately) between
the two pieces of the zero clearance throat plate and there
should be no play between the right slide bar and the
pivot assembly. Standing in front of the saw, make a visual
inspection. If adjustment is required:
JAM NUTS
SLIDE BAR
Unplug the saw.
With the miter at 0˚ and the bevel at 0˚, lock the saw into
the transport position.
Loosen the jam nuts on the two top and two bottom gib
screws as shown.
Loosen the two top gib screws.
Tighten or loosen the lower gib screws as required to
center the blade between the two pieces of the throat
plate.
GIB SCREW
PIVOT
ASSEMBLY
Once centered, tighten the lower two jam nuts.
NOTE: To minimize play in the slide bars, gradually tighten
the two top gib screws while sliding the saw back and forth
over the slide bars. Tighten the top jam nuts.
Fig. 16
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
ADJUSTING THE MITER LOCK LEVER
See Figures 17 - 18.
Prior to squaring the saw blade to the fence, check and align
the miter lock lever. The blade must be set at an “unindexed”
miter position other than 0˚, 15˚, 22.5˚, 31.6˚, 45˚, and 60˚ to
test. In the “locked” position, the action of pushing the miter
lock lever down should feel tight and secure. Considerable
effort should be required to move the miter table. If the table
moves easily when in the “locked” position, an adjustment
of the miter lock lever is required.
®
To adjust:
Unplug the saw.
MITER
LOCK
LEVER
Lift the miter lock lever to unlock.
Locate the set screw under the miter lock lever.
Using a hex key, adjust the set screw until the proper
amount of tension in the lock lever is attained.
Once all adjustments have been made, push the miter
lock lever down to relock the miter table.
SQUARING THE SAW BLADE TO THE FENCE
See Figures 19 - 23.
PUSH DOWN TO LOCK
Unplug the saw.
Fig. 18
Loosen the screws holding the throat plate and move
the throat plate as far away from the saw blade as
possible.
SOCKET HEAD
SCREW(S)
Pull the saw arm all the way down and lock in transport
position.
Lift the miter lock lever.
FENCE
SCREW
®
SOCKET
HEAD
SCREW
FENCE
MITER
LOCK
LEVER
Fig. 19
LIFT TO UNLOCK
Fig. 17
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Rotate the miter table until the pointer on the miter scale
is positioned at 0°.
Lock the miter lock lever by pushing it down.
Remove the sliding miter fence by loosening the fence
screw and lifting the sliding miter fence off the saw.
®
Lay a framing square flat on the miter table. Place one
leg of the square against the fence. Slide the other leg
of the square against the flat part of saw blade.
BLADE
NOTE: Make sure that the square contacts the flat part
of the saw blade, not the blade teeth.
The edge of the square and the saw blade should be
parallel as shown in figure 20.
If the front or back edge of the saw blade angles away
from the square as shown in figures 21 and 22, adjust-
ments are needed.
SLIDING
MITER
FENCE
FRAMING
SQUARE
Loosen the socket head screws that secure the fence to
MITER
TABLE
the miter table. See Figure 19.
Rotate the fence left or right until the saw blade is parallel
VIEW OF BLADE NOT SQUARE WITH FENCE,
ADJUSTMENTS ARE REQUIRED
with the square.
Fig. 21
Retighten the socket head screws securely and recheck
the blade-to-fence alignment.
Your saw has several scale indicators. After squaring adjust-
ments have been made, it may be necessary to loosen the
indicator screws and reset them to zero. See Figure 23.
®
BLADE
®
BLADE
SLIDING
MITER
FENCE
FRAMING
MITER
SQUARE
TABLE
VIEW OF BLADE NOT SQUARE WITH FENCE,
ADJUSTMENTS ARE REQUIRED
Fig. 22
SLIDING
MITER
FENCE
FRAMING
SQUARE
MITER
LOCK
LEVER
MITER
TABLE
VIEW OF BLADE SQUARE WITH FENCE
Fig. 20
MITER
SCALE
INDICATOR
SCREW
SCALE
INDICATOR
Fig. 23
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
ADJUSTING THE BEVEL LOCK LEVER
See Figures 24 - 25.
Prior to squaring the saw blade to the miter table, check
and align the bevel lock lever. The blade must be set at an
“unindexed” bevel position other than 0°, 22.5°, 33.9°, and
45° to test. In the “locked” position, the action of pushing the
bevel lock lever down should feel tight and secure.
BEVEL LOCK
LEVER
®
Considerable effort should be required to bevel the blade. If
the saw arm moves easily when in the “locked” position, an
adjustment of the bevel lock lever is required.
LIFT TO
UNLOCK
To adjust:
Unplug the saw.
Lift the bevel lock lever up to unlock.
Locate the two locking jam nuts behind the bevel lock
Fig. 24
lever.
Loosen the top jam nut. Turn the bottom jam nut clock-
wise to tighten and counterclockwise to loosen.
Once all adjustments have been made, push the bevel
lock lever down to relock the bevel.
®
ADJUSTING THE BEVEL PIVOT
See Figure 26.
PUSH DOWN
TO LOCK
The saw should freely pivot when the bevel lock lever is
“unlocked” and the saw is beveled. A “grating” sound
indicates that the bevel needs to be loosened slightly. If the
movement is tight or there is play in the pivot, an adjustment
is required.
NOTE: At least one thread of the pivot bolt should stick out
past the hex lock nut.
BEVEL
LOCK
LEVER
To adjust:
Fig. 25
Unplug the saw.
Lift the bevel lock lever up to unlock.
Turn the hex lock nut with 3/4 in. or 19 mm socket.
HEX LOCK
NUT
Once all adjustments have been made, push the bevel
lock lever down to relock the bevel.
TRAVEL PIVOT ADJUSTMENT
The saw arm should rise completely to the up position
by itself.
If the saw arm does not raise by itself or if there is play
in the pivot joints, have saw repaired at the nearest
authorized service center.
Fig. 26
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
SQUARING THE BLADE TO THE MITER TABLE
See Figures 27 - 30.
Unplug the saw.
®
BEVEL
LOCK
LEVER
Pull the saw arm all the way down and lock in transport
position.
BLADE
Lift the miter lock lever.
SLIDING
MITER
FENCE
Rotate the miter table until the pointer on the miter scale
is positioned at 0°.
Lock the miter lock lever by pushing it down.
Lift the bevel lock lever to loosen and set the saw at 0°
bevel (blade set 90° to miter table). Retighten the bevel
lock lever by pushing it down.
COMBINATION
SQUARE
Place a combination square against the miter table and
MITER
LOCK
LEVER
MITER
TABLE
the flat part of saw blade.
NOTE: Make sure that the square contacts the flat part
CORRECT VIEW OF BLADE
SQUARE WITH MITER TABLE
of the saw blade, not the blade teeth.
Rotate the blade by hand and check the blade-to-table
Fig. 28
alignment at several points.
®
The edge of the square and the saw blade should be
parallel as shown in figure 28.
If the top or bottom of the saw blade angles away from
the square as shown in figures 29 and 30, adjustments
are needed.
Lift the bevel lock lever.
Using the blade wrench, loosen the two socket head
screws securing the bevel scale and slide the pivot
assembly left or right as needed to bring the saw blade
into alignment with the square. Retighten the socket
head screws.
Retighten the bevel lock lever by pushing it down.
COMBINATION
SQUARE
Recheck blade-to-table alignment.
NOTE: The above procedure can be used to check blade
squareness of the saw blade to the miter table at both 0°
and 45° angles.
VIEW OF BLADE NOT SQUARE WITH MITER TABLE,
ADJUSTMENTS ARE REQUIRED
Fig. 29
Your saw has several scale indicators. After squaring adjust-
ments have been made, it may be necessary to loosen the
indicator screws and reset them to zero. See Figure 27.
®
BEVEL
SCALE
SCALE
INDICATOR
BEVEL
SCALE
COMBINATION
SQUARE
VIEW OF BLADE NOT SQUARE WITH MITER TABLE,
ADJUSTMENTS ARE REQUIRED
INDICATOR
SCREW
SOCKET HEAD
SCREW
Fig. 30
Fig. 27
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
Do not start the compound miter saw without
checking for interference between the blade and
the miter fence. Damage could result to the blade
if it strikes the miter fence during operation of the
saw.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
CUTTING WITH YOUR SLIDING COMPOUND
MITER SAW
WARNING:
When using a work clamp or C-clamp to secure
the workpiece, clamp workpiece on one side of the
blade only. The workpiece must remain free on one
side of the blade to prevent the blade from binding
in workpiece. The workpiece binding the blade will
cause motor stalling and kickback. This situation
could cause an accident resulting in possible seri-
ous personal injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool.
The use of attachments or accessories not recom-
mended can result in serious personal injury.
APPLICATIONS
You may use this tool to cut only wood or plastic as listed
below:
WARNING:
Cross cutting miters, joints, etc. for picture frames, mold-
To avoid serious personal injury, always tighten the
miter lock lever and the bevel lock lever securely
before making a cut. Failure to do so could result
in movement of the control arm or miter table while
making a cut.
ings, door casings, and fine joinery.
Bevel and compound cutting
Cross cutting wide workpieces.
NOTE: The blade provided is fine for most wood cutting
operations, but for fine joinery cuts or cutting plastic, use one
of the accessory blades available from the RIDGID dealer.
WARNING:
Do not try to cut narrow pieces using the sliding
feature. Failure to heed this warning could result in
serious personal injury.
WARNING:
Before starting any cutting operation, clamp or bolt
the miter saw to a workbench. Never operate the
miter saw on the floor or in a crouched position.
Failure to heed this warning can result in serious
personal injury.
WARNING:
To avoid serious personal injury, keep your hands
outside the no hands zone, at least 3 in. from blade.
Never perform any cutting operation freehand (with-
out holding workpiece against the fence). The blade
could grab the workpiece if it slips or twists.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SLIDE CUT
WARNING:
SLIDE SAW ARM
FORWARD THEN
PUSH DOWN
Never make a cut by pulling the saw toward you
as the blade can climb on top of the workpiece
and come toward you. Failure to heed this warning
could result in serious personal injury.
TO SLIDE CUT
See Figures 31 - 32.
The sliding feature will cut workpieces 13-1/2 in. wide
by 3-1/2 in. thick. With the saw off, pull the saw arm
forward. Turn the saw on (let blade reach maximum speed),
then push the blade down on top of the workpiece then back
toward the rear of the saw to make a cut. Cuts are made by:
(1) pushing the saw blade away from you and toward the
bevel scale at the back of the saw stopping when the full rear
position has been reached after each cut. When the saw is
running (turned on), NEVER pull the saw blade toward you
or toward the front of the saw.
Raise saw arm to its full height.
Fig. 31
Place the workpiece flat on the miter table with one edge
securely against the fence. If the board is warped, place
the convex side against the fence. If the concave edge
of a board is placed against the fence, the board could
collapse on the blade at the end of the cut, jamming the
blade. See Figures 47 - 48.
PUSH
BACK
When cutting long pieces of lumber or molding, support
the opposite end of the stock with a roller stand or with
a work surface level with the saw table. See Figure 40.
Align the cutting line on the workpiece with the edge of
saw blade.
Loosen the slide lock knob by turning the knob counter-
clockwise.
Grasp the stock firmly with one hand and secure it against
the fence. Use the work clamp or a C-clamp to secure
the workpiece when possible.
Before turning on the saw, perform a dry run of the cut-
ting operation to make sure that no problems will occur
when the cut is made.
Fig. 32
With the saw off, grasp the saw handle firmly then pull
the saw forward until the blade arbor (center of the saw
blade) is over the front of the workpiece.
Release the switch trigger and allow the saw blade to
stop rotating before raising the blade out of workpiece
and removing the workpiece from miter table.
Depress the switch lock with thumb then squeeze the
switch trigger. Allow several seconds for the blade to
reach maximum speed.
NOTE: A cross cut is made by cutting across the grain of
the workpiece. A straight cross cut is made with the miter
table set at the 0° position. Miter cross cuts are made with
the miter table set at some angle other than 0°.
Slowly lower the blade into and through the front edge
of the workpiece.
Push the saw handle away from you and toward the bevel
scale at the back of the saw.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO MAKE NON-SLIDING CUTS
WARNING:
Securely tighten the slide lock knob when making
any non-sliding cuts. Failure to tighten the knob
could result in the saw head moving during the
cutting operation.
®
TO MITER CUT / CROSS CUT
See Figures 33 - 34.
A cross cut is made by cutting across the grain of the
workpiece. A straight cross cut is made with the miter table
set at the 0° position. Miter cross cuts are made with the
miter table set at some angle other than 0°.
WORK
CLAMP
Make sure the slide lock knob is tightened securely.
Raise saw arm to its full height.
Lift the miter lock lever to unlock. Rotate the miter table
until the pointer aligns with the desired angle on the miter
scale.
NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, 45°,
and 60° left or right by spinning the miter thumbwheel up.
The lock plate will seat itself in one of the positive stop
notches, located in the miter table base.
CROSS CUT
Fig. 33
Push the miter lock lever down to lock the miter table.
Place the workpiece flat on the miter table with one edge
securely against the fence. If the board is warped, place
the convex side against the fence. If the concave edge
of a board is placed against the fence, the board could
collapse on the blade at the end of the cut, jamming the
blade. See Figures 47 - 48.
When cutting long pieces of lumber or molding, support
the opposite end of the stock with a roller stand or with
a work surface level with the saw table. See Figure 40.
WORK
CLAMP
Align cutting line on the workpiece with the edge of saw
blade.
Grasp the stock firmly with one hand and secure it against
the fence. Use the work clamp or a C-clamp to secure
the workpiece when possible.
Before turning on the saw, perform a dry run of the cut-
ting operation to make sure that no problems will occur
when the cut is made.
Grasp the saw handle firmly. Depress the switch lock
with thumb then squeeze the switch trigger. Allow several
seconds for the blade to reach maximum speed.
Slowly lower the blade into and through the workpiece.
6
.
1
3
.5
2
2
Release the switch trigger and allow the saw blade to
stop rotating before raising the blade out of workpiece
and removing the workpiece from the miter table.
MITER CUT
Fig. 34
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO BEVEL CUT
See Figures 35 - 37.
A bevel cut is made by cutting across the grain of the
workpiece with the blade angled to the workpiece. A straight
bevel cut is made with the miter table set at the zero degree
position and the blade set at an angle.
SCALE
INDICATOR
NOTE: It may be necessary to adjust or remove the sliding
miter fence to insure proper clearance prior to making the
cut.
Make sure the slide lock knob is tightened securely.
BEVEL
SCALE
Raise saw arm to its full height.
Lift the miter lock lever to unlock. Rotate the miter table
until the pointer aligns with zero on the miter scale.
Push the miter lock lever down to lock the miter table.
INDICATOR
SCREW
Fig. 35
Lift the bevel lock lever and move the saw arm to the left
or right to the desired bevel angle.
Once the saw arm has been set at the desired angle,
push the bevel lock lever down to lock.
Place the workpiece flat on the miter table with one edge
securely against the fence. If the board is warped, place
the convex side against the fence. If the concave edge
of a board is placed against the fence, the board could
collapse on the blade at the end of the cut, jamming the
blade. See Figures 47 - 48.
BEVEL CUT
When cutting long pieces of lumber or molding, support
the opposite end of the stock with a roller stand or with
a work surface level with the saw table. See Figure 40.
C-CLAMP
Align the cutting line on the workpiece with the edge of
saw blade.
Grasp the stock firmly with one hand and secure it against
the fence. Use the work clamp or a C-clamp to secure
the workpiece when possible.
Before turning on the saw, perform a dry run of the cut-
ting operation to make sure that no problems will occur
when the cut is made.
Grasp the saw handle firmly. Depress the switch lock
with thumb then squeeze the switch trigger. Allow several
seconds for the blade to reach maximum speed.
Fig. 36
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the saw blade to
stop rotating before raising the blade out of workpiece
and removing the workpiece from the miter table.
BEVEL
LOCK PIN
Fig. 37
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO COMPOUND MITER CUT
See Figure 38.
A compound miter cut is a cut made using a miter angle and
a bevel angle at the same time. This type of cut is used to
make picture frames, cut molding, make boxes with sloping
sides, and for certain roof framing cuts.
COMPOUND
MITER CUT
To make this type of cut the control arm on the miter table
must be rotated to the correct angle and the saw arm must
be tilted to the correct bevel angle. Care should always
be taken when making compound miter setups due to the
interaction of the two angle settings.
Adjustments of miter and bevel settings are interdependent
with one another. Each time you adjust the miter setting you
change the effect of the bevel setting. Also, each time you
adjust the bevel setting you change the effect of the miter
setting.
6
.
1
3
.5
2
2
It may take several settings to obtain the desired cut. The
firstanglesettingshouldbecheckedaftersettingthesecond
angle, since adjusting the second angle affects the first.
Once the two correct settings for a particular cut have been
obtained, always make a test cut in scrap material before
making a finish cut in good material.
Fig. 38
the fence. Use the work clamp or a C-clamp to secure
the workpiece when possible.
NOTE: It may be necessary to adjust or remove the sliding
miter fence to insure proper clearance prior to making the
cut.
Before turning on the saw, perform a dry run of the cut-
ting operation to make sure that no problems will occur
when the cut is made.
Make sure the slide lock knob is tightened securely.
Raise saw arm to its full height.
Make a test cut in scrap material.
Lift the miter lock lever to unlock. Rotate the miter table
until the pointer aligns with the desired angle on the miter
scale.
Grasp the saw handle firmly. Depress the switch lock
with thumb then squeeze the switch trigger. Allow several
seconds for the blade to reach maximum speed.
NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, 45°,
and 60° left or right by spinning the miter thumbwheel up.
The lock plate will seat itself in one of the positive stop
notches, located in the miter table base.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the saw blade to
stop rotating before raising the blade out of workpiece
and removing the workpiece from the miter table.
Push the miter lock lever down to lock the miter table.
Lift the bevel lock lever and move the saw arm to the left
or right to the desired bevel angle.
Once the saw arm has been set at the desired angle,
securely tighten the bevel lock lever.
Place the workpiece flat on the miter table with one edge
securely against the fence. If the board is warped, place
the convex side against the fence. If the concave edge
of a board is placed against the fence, the board could
collapse on the blade at the end of the cut, jamming the
blade. See Figures 47 - 48.
When cutting long pieces of lumber or molding, support
the opposite end of the stock with a roller stand or with
a work surface level with the saw table. See Figure 40.
Align the cutting line on the workpiece with the edge of
saw blade.
Grasp the stock firmly with one hand and secure it against
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SUPPORTING LONG WORKPIECES
See Figures 39 - 40.
Long workpieces need extra supports. Supports should be
placed along the workpiece so it does not sag. The support
should let the workpiece lay flat on the base of the saw and
mitertableduringthecuttingoperation. Usethe workclamp
or a C-clamp to secure the workpiece.
®
NOTE: When making a compound miter cut as shown
in figure 39, it may be necessary to adjust or remove the
sliding miter fence to insure proper clearance prior to
making the cut.
LONG
WORKPIECE
WORKPIECE
SUPPORTS
Fig. 40
CLAMPING WIDE WORKPIECES
See Figure 42.
When cutting wide workpieces, such as 2 in. x 12 in., boards
should be clamped with a C-clamp.
6
.
1
3
.5
2
2
®
45° x 45° COMPOUND MITER CUT
Fig. 39
WIDE BOARD
Fig. 41
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ROUGH CUTTING A DADO
See Figures 42 - 43.
DEPTH GUIDE
Using a wood chisel and the depth guide, it is possible to
make a rough dado cut. The marks on the depth guide are
to be used for reference only. Always make a practice cut
on scrap wood.
To make the cut:
Unlock the slide lock knob.
Raise the saw arm to its full height.
Using the marks on the depth guide, set the blade to the
correct cutting depth.
With the saw off, pull the saw arm forward. Turn the saw
on (let blade reach maximum speed), then push the blade
down on top of the workpiece then back toward the rear
of the saw to make a cut.
Cut two outside grooves in the workpiece.
Fig. 42
Using a wood chisel, remove the material between the
two outside grooves.
CUT THESE GROOVES
WITH SAW
USING AN AUXILIARY FENCE
See Figure 44.
Certain unusual cuts may benefit from a thicker miter fence
(auxiliary fence) due to the size and position of the workpiece.
The holes provided in the miter fence are there for just this
purpose. The miter fence holes are used to secure the
auxiliary fence which requires a piece of wood 1/2 in. thick,
4-1/4 in. high, and 23 in. long to make.
NOTE: The auxiliary fence can only be used when the bevel
is set at 0˚. When making a bevel cut, the auxiliary fence
MUST be removed.
USE A CHISEL TO CUT
OUT THE MIDDLE
WORKPIECE
To attach the auxiliary fence to the saw:
Place the wood against the miter fence and mark the hole
Fig. 43
location from behind the fence using a pencil.
Drill holes through the wood then countersink the holes
on the front of the wood.
Secure the wood to the miter fence using flat head
screws.
With the miter table set at 0˚, make a complete cut
through the auxiliary fence to create the blade slot.
AUXILIARY FENCE
NOTE: Check for interference between the auxiliary fence
and the lower blade guard. Correct any interference
before proceeding.
.6
1
3
.5
2
2
Fig. 44
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CUTTING COMPOUND MITERS
To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are
the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made,
prior to making your required cut.
NUMBER OF SIDES
PITCH
OF SIDE
4
5
6
7
8
9
10
M- 30.00°
B- 0.00°
M- 45.00° M- 36.00°
B- 0.00° B- 0.00°
M- 22.50°
B- 0.00°
M- 25.71°
B- 0.00°
M- 20.00° M- 18.00°
B- 0.00° B- 0.00°
0°
M- 22.42°
B- 1.91°
M- 17.94°
M- 19.93°
M- 44.89°
B- 3.53°
M- 35.90° M- 29.91° M- 25.63°
B- 2.94° B- 2.50° B- 2.17°
5°
10°
15°
20°
25°
30°
35°
40°
45°
B- 1.54°
B- 1.71°
M- 44.56° M- 35.58°
B- 7.05° B- 5.86°
M- 19.72°
B- 3.40°
M- 29.62° M- 25.37° M- 22.19°
B- 4.98° B- 4.32° B- 3.81°
M- 17.74°
B- 3.08°
M- 44.01° M- 35.06° M- 29.15°
B- 10.55° B- 8.75° B- 7.44°
M- 21.81° M- 19.37° M- 17.42°
B- 5.68° B- 5.08° B- 4.59°
M- 24.95°
B- 6.45°
M- 28.48°
B- 9.85°
M- 34.32°
B- 11.60°
M- 24.35° M- 21.27° M- 18.88° M- 16.98°
B- 8.53° B- 7.52° B- 6.72° B- 6.07°
M- 43.22°
B- 14.00°
M- 42.19° M- 33.36° M- 27.62° M- 23.56° M- 20.58° M- 18.26°
B- 17.39° B- 14.38° B- 12.20° B- 10.57° B- 9.31° B- 8.31°
M- 16.41°
B- 7.50°
M- 40.89° M- 32.18° M- 26.57° M- 22.64° M- 19.73° M- 17.50°
B- 20.70° B- 17.09° B- 14.48° B- 12.53° B- 11.03° B- 9.85°
M- 15.72°
B- 8.89°
M- 39.32°
B- 23.93°
M- 25.31°
B- 16.67°
M- 16.60°
B- 11.31°
M- 30.76°
B- 19.70°
M- 21.53° M- 18.74°
B- 14.41° B- 12.68°
M- 14.90°
B- 10.21°
M- 37.45° M- 29.10°
B- 27.03° B- 22.20°
M- 20.25° M- 17.60° M- 15.58°
B- 16.19° B- 14.24° B- 12.70°
M- 23.86°
B- 18.75°
M- 13.98°
B- 11.46°
M- 35.26°
B- 30.00°
M- 22.21°
B- 20.70°
M- 14.43°
B- 14.00°
M- 27.19°
B- 24.56°
M- 18.80° M- 16.32°
B- 17.87° B- 15.70°
M- 12.94°
B- 12.62°
M- 32.73°
B- 32.80°
M- 20.36°
B- 22.52°
M- 25.03°
B- 26.76°
M- 17.20° M- 14.91° M- 13.17° M- 11.80°
B- 19.41° B- 17.05° B- 15.19° B- 13.69°
50°
55°
60°
65°
70°
75°
80°
85°
90°
M- 18.32°
B- 24.18°
M- 29.84° M- 22.62°
B- 35.40° B- 28.78°
M- 15.44° M- 13.36° M- 11.79° M- 10.56°
B- 20.82° B- 18.27° B- 16.27° B- 14.66°
M- 19.96°
B- 30.60°
M- 13.54° M- 11.70° M- 10.31°
B- 22.07° B- 19.35° B- 17.23°
M- 26.57°
B- 37.76°
M- 16.10°
B- 25.66°
M- 9.23°
B- 15.52°
M- 13.71°
B- 26.95°
M- 7.82°
B -16.26°
M- 22.91° M- 17.07°
B- 39.86° B- 32.19°
M- 11.50° M- 9.93° M- 8.74°
B- 23.16° B- 20.29° B- 18.06°
M- 11.17°
B- 28.02°
M- 18.88° M- 13.95°
B- 41.64° B- 33.53°
M- 9.35° M- 8.06° M- 7.10°
B- 24.06° B- 21.08° B- 18.75°
M- 6.34°
B- 16.88°
M- 14.51° M- 10.65°
B- 43.08° B- 34.59°
M- 7.10° M- 6.12° M- 5.38°
B- 24.78° B- 21.69° B- 19.29°
M- 8.50°
B- 28.88°
M- 5.73°
B- 29.50°
M- 4.81°
B- 17.37°
M- 9.85° M- 7.19°
B- 44.14° B- 35.37°
M- 4.98°
B- 44.78°
M- 4.78° M- 4.11° M- 3.62° M- 3.23°
B- 25.30° B- 22.14° B- 19.68° B- 17.72°
M- 3.62°
B- 35.84°
M- 2.40° M- 2.07° M- 1.82°
B- 25.61° B- 22.41° B- 19.92°
M- 2.88°
B- 29.87°
M- 1.62°
B- 17.93°
M- 0.00° M- 0.00° M- 0.00° M- 0.00° M- 0.00° M- 0.00°
B- 36.00° B- 30.00° B- 25.71° B- 22.50° B- 20.00° B- 18.00°
M- 0.00°
B- 45.00°
Each B (Bevel) and M (Miter) Setting is Given to the Closest 0.005°.
COMPOUND-ANGLE SETTINGS FOR POPULAR STRUCTURES
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
When cutting crown molding by this method, the bevel angle
should be set at 33.85°. The miter angle should be set at
31.6° either right or left, depending on the desired cut for the
application. See the chart below for correct angle settings
and correct positioning of crown molding on miter table.
The settings in the chart below can be used for cutting All
Standard (U.S.) crown molding with 52° and 38° angles. The
crown molding is placed flat on the miter table using the
compound features of your miter saw.
CUTTING CROWN MOLDING
The compound miter saw does an excellent job of cutting
crown molding. In general, compound miter saws do a better
job of cutting crown molding than any other tool made.
In order to fit properly, crown molding must be compound
mitered with extreme accuracy.
The two contact surfaces on a piece of crown molding that
fit flat against the ceiling and the wall of a room are at angles
that, when added together, equal exactly 90°. Most crown
molding has a top rear angle (the section that fits flat against
the ceiling) of 52° and a bottom rear angle (the section that
fits flat against the wall) of 38°.
Bevel
Angle
Type of Cut
Setting
Left side, inside corner
LAYING MOLDING FLAT ON THE MITER
TABLE
See Figure 45.
1. Top edge of molding against fence
2. Miter table set right 31.62°
3. Save left end of cut
33.85°
33.85°
33.85°
33.85°
To use this method for accurately cutting crown molding for
a 90° inside or outside corner, lay the molding with its broad
back surface flat on the miter table and against the fence.
Right side, inside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62°
3. Save left end of cut
When setting the bevel and miter angles for compound
miters, remember that the settings are interdependent;
changing one angle changes the other angle as well.
Left side, outside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62°
3. Save right end of cut
Keep in mind that the angles for crown molding are very
precise and difficult to set. Since it is very easy for these
angles to shift, all settings should first be tested on scrap
molding. Also most walls do not have angles of exactly 90°;
therefore, you will need to fine tune your settings.
Right side, outside corner
1. Top edge of molding against fence
2. Miter table set right 31.62°
3. Save right end of cut
52°
CEILING
38°
W
A
L
L
FENCE
INSIDE
CORNER
OUTSIDE CORNER
FENCE
TOP EDGE AGAINST FENCE =
LEFT SIDE, INSIDE CORNER
RIGHT SIDE, OUTSIDE CORNER
BOTTOM EDGE AGAINST FENCE =
RIGHT SIDE, INSIDE CORNER
LEFT SIDE, OUTSIDE CORNER
MITER TABLE
MITER TABLE
CROWN MOLDING FLAT ON MITER TABLE
Fig. 45
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
USING A CROWN MOLDING SUPPORT JIG
Bevel
Place the crown molding upside down on the miter table
Angle
Type of Cut
with the bottom of the molding against the wood fence.
Setting
Use the chart on this and the previous page to select the
Left side, inside corner
proper miter angle.
1. Top edge of molding against fence
2. Miter table set right 45°
3. Save left end of cut
0°
0°
0°
0°
Lift the miter lock lever and position the miter table to
the desired setting. Push the miter lock lever down to
securely tighten the miter table.
Right side, inside corner
Make sure the slide lock knob is tightened securely.
1. Bottom edge of molding against fence
2. Miter table set left 45°
Slowly lower the blade into and through the molding.
Release the switch trigger and allow the saw blade to
stop rotating before raising the blade out of workpiece
and removing the workpiece from the miter table.
3. Save left end of cut
Left side, outside corner
1. Bottom edge of molding against fence
2. Miter table set left 45°
3. Save right end of cut
Right side, outside corner
1. Top edge of molding against fence
2. Miter table set right 45°
3. Save right end of cut
MAKING A CROWN MOLDING SUPPORT JIG
See Figure 46.
CROWN
MOLDING JIG
A crown molding support jig will need to be made when
cutting crown molding with no required bevel setting. The
support jig holds the crown molding in place during the
cutting operation. When using this method, the saw can
be quickly adjusted for corners that are not 90° square.
NOTE: A separate support jig must be made for different
widths.
To make a support jig:
Using a piece of wood 1/2 in. thick, 4-1/4 in. high, and
23 in. long, place the wood on the miter table against the
miter fence.
6
.
1
3
From the back side of the saw, use a pencil to mark the
.5
2
2
wood through the holes in the miter fences.
Drill holes through the wood then countersink the holes
to accept flat head screws.
Attach the wood to the fence using the flat head
Fig. 46
screws.
Place a piece of crown molding firmly against the miter
table and the wood. Mark the height of the molding with
a pencil.
Remove the screws and the wood from the miter fence
then cut the wood to this width.
Using small nails and glue, attach a piece of wood
(1/2 in. thick x 1-1/2 in. wide x 23-1/2 or 28 in. long) to
the top of the wood.
NOTE: Keep nails away from the area around the blade
cutting path.
Securely reattach the support jig to the miter fence.
Make a full 45° left miter cut and a 45° right miter cut
through the completed support jig.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CUTTING WARPED MATERIAL
See Figures 47 - 48.
When cutting warped material, always make sure it is
positioned on the miter table with the convex side against
the fence as shown in figure 47.
If the warped material is positioned the wrong way as shown
in figure 48, it will pinch the blade near the completion of
the cut.
WRONG
Fig. 48
WARNING:
To avoid kickback and serious personal injury,
never position the concave edge of bowed or
warped material against the fence.
RIGHT
Fig. 47
ADJUSTMENTS
NOTE: When properly aligned, the laser should be on the
left edge of the kerf.
WARNING:
Once aligned, remove and store the hex key (1/16 in.),
Before performing any adjustment, make sure the
tool is unplugged from the power supply. Failure to
heed this warning could result in serious personal
injury.
and lower the blade guard.
NOTE: Always make practice cuts on scrap wood before
cutting through your workpiece.
ADJUSTMENT
SCREW
TO ADJUST THE LASER GUIDE
See Figure 49.
NOTE: Avoid direct eye exposure when using the laser
guide.
Set both the bevel angle and the miter table at 0°.
Use the work clamp or a C-clamp to secure a piece of
scrap wood.
Plug the saw into the power source and make a slight
cut to score the wood.
Raise the saw arm and unplug the saw.
LASER
BUTTON
Lift and hold the lower blade guard.
APERTURE
Rotate the blade by hand until you can push and hold
the laser button and the laser is near the center of the
workpiece as shown in figure 49.
HEX
KEY
To adjust the laser, turn the adjustment screw coun-
ter-clockwise or clockwise using the hex key (1/16 in.)
provided.
LASER
MARK
Fig. 49
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other part may create a hazard
or cause product damage.
BRUSH
CAP
BRUSH
ASSEMBLY
BRUSH
ASSEMBLY
®
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
BRUSH
CAP
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc., come
in contact with plastic parts. They contain chemi-
cals that can damage, weaken or destroy plastic.
Fig. 50
1/4 in.
BELT COVER
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
BELT
WARNING:
To ensure safety and reliability, all repairs should be
performed by a qualified service technician at an
authorized service center to avoid risk of personal
injury.
BELT
MOTOR MOUNT
SCREWS
ADJUSTING
SOCKET HEAD
SCREW
Some areas will require infrequent lubrications. You will need
to apply:
Automotive oil directly to the slide bars.
Light oil or a pressurized light spray oil to the arm pivot
shaft.
Light oil or a pressurized light spray oil to the torsion
spring.
BRUSH REPLACEMENT
See Figure 50.
The saw has externally accessible brush assemblies that
should be periodically checked for wear.
Proceed as follows when replacement is required:
Unplug the saw.
Fig. 51
36
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
When replacing the batteries, the laser guide should be
thoroughly cleaned. Use a soft paintbrush, or similar
device, to remove all sawdust and debris.
WARNING:
Failure to unplug the saw could result in accidental
starting causing serious injury.
After cleaning the laser guide and replacing batteries,
secure battery cover to laser guide using the screw.
Tighten screw securely.
Remove brush cap with a screwdriver. Brush assembly is
spring loaded and will pop out when you remove brush
cap.
CAUTION:
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Remove brush assembly.
Check for wear. Replace both brushes when either has
less than 1/4 in. length of carbon remaining. Do not
replace one side without replacing the other.
Reassemble using new brush assemblies. Make sure
curvature of brush matches curvature of motor and that
brush moves freely in brush tube.
Make sure brush cap is oriented correctly (straight) and
replace.
Tighten brush cap securely. Do not overtighten.
MOTOR BELT TENSION
See Figure 51.
SCREW
The motor belt tension was adjusted at the factory but should
still be checked periodically.
BATTERY
COVER
To check belt tension:
Using a phillips screwdriver, remove the screws holding
the belt cover. Lift off the cover.
Check belt tension by squeezing the belt. Using light
pressure, the belt should deflect approximately 1/4 in.
BATTERIES
To adjust belt tension:
Loosen, but don’t remove, the six motor mount screws.
Increase the belt tension by turning the adjusting socket
head set screw clockwise. Decrease the belt tension by
turning the set screw counterclockwise.
BATTERY
COVER
NEGATIVE (–)
NOTE: Excessive belt tension will cause the motor to fail
prematurely.
Securely tighten the six motor mount screws.
Replace the belt cover and tighten securely using
screws.
CHANGING THE BATTERIES
See Figure 52.
Unplug the saw.
Rotate and hold lower blade guard up.
Using the hex key (1/16 in.) provided, loosen and remove
the screw from the battery cover then separate the cover
from the laser guide.
Fig. 52
Lower the blade guard.
Remove the three button cell batteries.
NOTE: Replace the batteries with button cell batteries
that have a rating of 1.5 volt and 100 mAh (milliampere
hour) minimum (number 76 series or equivalent).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Look for these accessories at The Home Depot.
AC9940.................................... Miter Saw Utility Vehicle
WARNING:
Current attachments and accessories available for use with this tool are listed above. Do not use any attachments
or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
NOTES
38
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at re-
tail and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than
an authorized service center for RIDGID® branded hand
held and stationary power tools. Consumable accessories
provided with the tool such as, but not limited to, blades,
bits and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID®, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID®
Hand Held and Stationary Power Tool Technical Service at
(toll free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
RIDGID®, INC. AND ONE WORLD TECHNOLOGIES,
INC. MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE OF
ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY
STATED IN THIS WARRANTY.
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warran-
ties, including warranties of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE, are disclaimed. Any implied
warranties, including warranties of merchantability or fitness
for a particular purpose, that cannot be disclaimed under
state law are limited to three years from the date of purchase.
One World Technologies, Inc. and RIDGID®, Inc. are not
responsible for direct, indirect, incidental or consequential
damages. Some states do not allow limitations on how long
an implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights
which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will
repair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
12 in. SLIDING COMPOUND MITER
SAW WITH LASER
Double Insulated
MS1290LZA
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service
center.Besuretoprovideallrelevantinformationwhenyoucallorvisit.
For the location of the authorized service center nearest you, please
Themodelnumberofthistoolisfoundonaplateattachedtothemotor
housing. Pleaserecordtheserialnumberinthespaceprovidedbelow.
When ordering repair parts, always give the following information:
MS1290LZA
Model No.
Serial No.
987000-017
8-16-07 (REV: 01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Radio Shack Electronic Keyboard CK 480 User Guide
RCA Home Theater System RTD317W User Guide
RCA Projection Television HD44LPW164 User Guide
Regency Wraps Indoor Fireplace U29 LP1 User Guide
Regency Wraps Indoor Fireplace Z2510L User Guide
Russound Stereo Amplifier DPA 612 User Guide
Samsung Digital Camera EC L200ZSBA User Guide
Samsung Flat Panel Television 400DX 3 User Guide
Sanyo Projector PLV Z700 User Guide
Senco Nail Gun E XP Series User Guide