RB-214
RB-215
Core Drilling
Machines
OPERATOR’S
MANUAL
• Pour français voire page 13
• Para el castellano vea la
página 27
WARNING!
Read this Operator’s Manual
carefully before using this
tool. Failure to understand
and follow the contents of
this manual may result in
electrical shock, fire and/or
serious personal injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215
Core Drilling Machine
Core Drilling Machines
Record Serial Number below and retain product serial number which is located on nameplate.
Serial
No.
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
• When operating a power tool outside, use an out-
door extension cord marked “W-A” or “W”. These
cords are rated for outdoor use and reduce the risk of
electrical shock.
General Safety Information
WARNING! Read and understand all instructions. Failure
to follow all instructions listed below may
result in electric shock, fire, and/or serious
personal injury.
• Use only three-wire extension cords which have
three-prong grounding plugs and three-pole re-
ceptacles which accept the tool’s plug. Use of other
extension cords will not ground the tool and increase
the risk of electrical shock.
SAVE THESE INSTRUCTIONS!
Work Area Safety
• Keep your work area clean and well lit. Cluttered
• Use proper extension cords. (See chart.) Insufficient
conductor size will cause excessive voltage drop, loss
of power.
benches and dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Tools create sparks which
may ignite the dust or fumes.
Minimum Wire Gauge for Extension Cord
Nameplate
Amps
Total Length (in feet)
0 – 25
26 – 50
16 AWG
16 AWG
16 AWG
51 – 100
16 AWG
14 AWG
14 AWG
• Keep bystanders, children, and visitors away
while operating a tool. Distractions can cause you to
lose control.
0 – 6
18 AWG
18 AWG
16 AWG
14 AWG
6 – 10
10 – 12
12 – 16
12 AWG
NOT RECOMMENDED
Electrical Safety
• Grounded tools must be plugged into an outlet,
properly installed and grounded in accordance
with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do
not use any adapter plugs. Check with a qualified
electrician if you are in doubt as to whether the out-
let is properly grounded. If the tools should electrically
malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user.
• Keep all electric connections dry and off the
ground. Do not touch plugs or tool with wet hands.
Reduces the risk of electrical shock.
Personal Safety
• Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medications. A moment of inattention
while operating power tools may result in serious per-
sonal injury.
Grounded
Receptacle
• Dress properly. Do not wear loose clothing or jew-
elry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure switch is OFF
before plugging in. Carrying tools with your finger on
the switch or plugging tools in that have the switch ON
invites accidents.
Extension Cord
• Avoid body contact with grounded surfaces. There
is an increased risk of electrical shock if your body is
grounded.
• Remove adjusting keys before turning the tool
ON. A wrench or a key that is left attached to a rotating
part of the tool may result in personal injury.
• Do not expose electrical tools to rain or wet con-
ditions. Water entering a tool will increase the risk of
electrical shock.
• Do not over-reach. Keep proper footing and bal-
ance at all times. Proper footing and balance enables
better control of the tool in unexpected situations.
• Do not abuse cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electrical shock.
• Wear hearing protectors, ear plugs or muffs when
using tool. Noise level may affect hearing with pro-
longed use.
• Use safety equipment. Always wear eye protec-
2
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
tion. Dusk mask, non-skid safety shoes, hard hat or
hearing protection must be used for appropriate con-
ditions.
Specific Safety Information
WARNING!
WARNING
Some dust created by power sanding,
Read this operator’s manual carefully before using
the Core Drilling Machine. Failure to understand
and follow the contents of this manual may result in
electrical shock, fire and/or serious personal injury.
sawing, grinding, drilling and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
Call the Ridge Tool Company, Technical Service
Department at (800) 519-3456 if you have any questions.
• lead from lead-based paints
• crystalline silica from bricks and cement and other
masonry products
Machine Safety
• arsenic and chromium from chemically-treated lumber
• Core Drilling Machine is made to drill holes in
granite, masonry and steel reinforced concrete.
Follow instructions on proper use of this machine.
Do not use for other purposes. Other uses or mod-
ifying this machine for other applications may increase
the risk of serious injury.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your ex-
posure to these chemicals: work in a well ventilated
area and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
• Do not wear loose cloth gloves or loose clothing
when operating machine. Wear only leather gloves.
Keep sleeves and jackets buttoned. Do not reach
across the machine or drill bit. Clothing can be
caught by the machine resulting in entanglement and
serious injury.
Tool Use and Care
• Do not use if switch does not turn it ON or OFF.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Disconnect the plug from the power source before
making any adjustments, changing accessories
or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
• Use extreme caution when drilling through floors.
Provide protection of all personnel and material
below the area. Cores generally drop from the drill at
completion of the hole.
• Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
• Keep fingers and hands away from drill bit. This
practice will prevent entanglement and reduces risk of
being cut.
• Check for misalignment or binding of moving
parts, breakage of parts and any other condition
that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many acci-
dents are caused by poorly maintained tools.
• Secure drill stand to the work surface. Use bolts,
ceiling jack or vacuum hold-down. Do not secure
with a vacuum hold-down when drilling on vertical
surfaces such as walls. Drill stand must be prop-
erly secured to prevent bit damage and serious injury.
• Use only accessories that are recommended for
your tool. Accessories that may be suitable for one tool
may become hazardous when used on another tool.
• When releasing carriage locking handle, maintain
a firm grip on feed handle to prevent feed handle
from revolving due to weight of drill. Rotating han-
dle can result in injury.
• Keep handles dry and clean; free from oil and
grease. Allows for better control of the tool.
• Do not force drill bit. Drill should be used at a
speed and feed rate that does not overload the
motor. When starting bits, do not use more than two
12″ extensions. Less likely to bind and lose control.
Service
• Tool service must be performed only by qualified re-
pair personnel. Service or maintenance performed
by unqualified repair personnel could result in injury.
• When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
Section of this manual. Use of unauthorized parts or
failure to follow maintenance instructions may create a
risk of electrical shock or injury.
Ridge Tool Company
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Description, Specifications and
Standard Equipment
Description
Ceiling Jack Screw
Mast with Gear Rack
Shim Adjusting
Screw (6)
Head Carriage
The RIDGID No. RB-214 and RB-215 are heavy-duty
1
2
Core Drilling Machines. Drilling bit sizes range from / ″
Warning Plate
through 14″. The RB-214 Machine has a combination an-
chor/vacuum base which provides additional flexibility
by incorporating both bases in one unit. The RB-215
has an anchor base only. The Diamond Core Bits are ca-
pable of drilling through granite, masonry and steel
reinforced concrete.
Carriage
Locking Handle
Drill
Feed Handle
Specifications
Power Source................30 amp, 115V, 60Hz
Vacuum Gauge
Spindle
Drill Motor Type 2..........2 Speed, 20 amp, 115V, 60Hz,
Single Phase, 400/900 RPM
Vacuum
Motor
Vacuum Water Trap
1
2
Drilling Capacity ............ / ″ through 14″ w/Spacer
Vacuum Slot Cap
Drill Feeding ..................Rack & Pinion Gear Type
Combination
Anchor/Vacuum
Base
Base ..............................Anchor Vacuum (13″ x 17″)
1
2
Mast...............................2 / ″ sq. x 42″ high
Wheel (2)
Leveling Screw (4)
Slide Carriage................Single Piece Aluminum
Control Panel.................Box w/Amp-Meter, 2 Switches,
2 Outlets
Figure 1A – RB-214 Core Drilling Machine
Vacuum System
(RB-214 Only) ...............Diaphragm Pump w/Vacuum
Gauge
1
4
Output Spindle Shaft .....Thread Size 1 / -7 UNC
Operation.......................900 RPM – 1/2″ - 4″ Bits
400 RPM – 4″ - 14″ Bits
Vacuum Pump
Switch
Needle
Amp-Meter
Drill Motor
Switch
Figure 1B – RB-215 Core Drilling Machine
4
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Machine Inspection
Machine and Work Area Set-Up
WARNING!
WARNING!
To prevent serious injury, inspect your Core Drilling
Machine. The following inspection procedures
should be performed on a daily basis:
To prevent serious injury, proper set-up of the
machine and work area is required. The following
procedures should be following to set-up the ma-
chine.
1. Make sure Core Drilling Machine is unplugged and the
1. Check that the work area has the following:
drill mast switch is set to the OFF position (Figure 1).
• Adequate lighting.
2. Inspect the vacuum seal for wear or damage. Replace
if necessary.
• No Flammable liquids, vapors or dust that may ig-
nite.
3. Inspect the power cord and plug for damage. If the
plug has been modified, is missing the grounding
prong or if the cord is damaged, do not use the
Threading Machine until the cord has been replaced.
• Grounded electrical outlet.
• Clear path to the electrical outlet that does not
contain any sources of heat or oil, sharp edges or
moving parts that may damage electrical cord.
4. Inspect the Core Drilling Machine for any broken,
missing, misaligned or binding parts as well as any
other conditions which may affect the safe and normal
operation of the machine. If any of these conditions
are present, do not use the machine until any problem
has been repaired.
2. Clean up the work area prior to setting up any
equipment. Move tools and debris to prevent slips
and falls.
3. Make sure drill motor ON/OFF switch is in the OFF
position.
5. Lubricate the Core Drilling Machine if necessary ac-
cording to the Maintenance Instructions.
4. When plugging the Core Drilling Machine into the
electrical outlet make sure to position the power cord
along the clear path selected earlier. Use an exten-
sion cord in good condition.
6. Use drill bits and accessories that are designed for
your Core Drilling Machine and meet the needs of your
application. The correct tools and accessories allow
you to do the job successfully and safely. Accessories
designed for use with other equipment may be haz-
ardous when used with this Core Drilling Machine.
WARNING
To avoid electrical shock and electrical
fires, never use an extension cord that is damaged or
does not meet the following requirements:
• The cord has a three-prong plug similar to shown
in Electrical Safety section.
7. Clean any oil, grease or dirt from all handles and
controls. This reduces the risk of injury due to a tool or
control slipping from your grip.
• The cord is rated as “W” or “W-A” if being used
outdoors.
• The cord has sufficient wire thickness (12 AWG
below 50′). If the wire thickness is too small, the
cord may overheat, melting the cord’s insulation or
causing nearby objects to ignite.
Inspect the cutting edges of your drill bits. If neces-
sary, have them replaced prior to using the Core
Drilling Machine. Bit is considered worn when the
crown shows excessive wear and has become flush
with tube. Dull or damaged cutting tools can lead to
binding and tool breakage.
WARNING
To reduce risk of electrical shock, keep all
electrical connections dry and off the ground. Do not
touch plug with wet hands.
Ridge Tool Company
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Vacuum Anchor Method-to-Floor
(RB-214 Only)
Securing Machine
WARNING!
The Vacuum Anchor Method is recommended for 8″
diameter holes or less. The Anchor Vacuum Method is
NOT recommended on rough or cracked floor conditions,
holes deeper than one bit length, or steel concentration
greater than standard rebar.
WARNING
Do not use Vacuum Anchor Method to
mount machine to a wall.
Drilling machine must be properly secured to the
work surface to prevent serious injury to the op-
erator.
Movement during drilling will cause chatter of bit
against work surface, fracturing diamonds. Bit
may also bind in hole causing damage to the bit.
Vacuum Anchor method should not be used to
mount machine to a wall.
1. Turn machine on its back and insert vacuum seal
(Figure 3) under machine base, inspecting first to en-
sure seal is in good condition and sealing groove is
clean.
2. Turn Drilling Machine up-right and loosen 4 base
leveling screws.
3. Plug power cord into a properly grounded recepta-
cle and turn vacuum pump ON/OFF switch to the
ON position.
Bolt Anchor Method-to-Floor
1. Measure distance from center of anchor bolt slot in
base (Figure 2) to center of drill spindle (Figure 1).
4. Insert vacuum slot cap into anchor bolt slot (Figure
2) and check vacuum and hose connections.
Vacuum gauge (Figure 2) must read a minimum
of 20″ of mercury.
2. To locate the anchor bolt hole, use the distance ob-
tained in Step 1 and measure from the center of the
hole that is to be drilled.
5. The drilling machine should now be vacuum anchored.
If machine does not anchor, add weight by standing on
vacuum base. It should now anchor with vacuum
gauge reading 20″ of mercury minimum. If not, check
the floor and vacuum seal (Figure 3) for leaks.
1
2
3. Drill and set / ″ anchor bolt. Place Drilling Machine
over anchor hole and hand tighten anchor bolt.
4. Adjust 4 leveling screws (Figure 1) to stabilize base
and plumb mast. Secure machine by tightening an-
chor bolt.
Bolt Anchor Method-to-Wall
Use the same bolt anchor method procedure to anchor
as above.
WARNING
Also fasten a chain to the Core Drilling
Machine and secure the chain to prevent the machine
falling and causing serious injury.
Vacuum Gauge
Vacuum
Vacuum
Release Valve
Water Trap
Vacuum
Slot Cap
Opening
Figure 3 – Installing Vacuum Seal
Anchor
Bolt Slot
6. Adjust 4 leveling screws to eliminate rocking and to
stabilize machine and plumb mast. The machine is
now ready to drill.
Figure 2 – Vacuum Motor and Base
6
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
7. Frequently check the water level in the vacuum water
trap. When water trap becomes half full, stop drilling
and empty water.
over 4″. Make certain speed is proper for bit diame-
ter being used.
CAUTION
DO NOT move speed selector while drill
spindle is rotating.
8. After using, turn drill motor ON/OFF switch to the
OFF position, then turn vacuum motor ON/OFF switch
to the OFF position, unplug power cord and remove,
clean and store vacuum seal.
NOTE! If a water collector ring and pump is used, plug
pump into a properly grounded 115V receptacle.
Have suitable container for draining.
4. With water control valve shut OFF. connect water
inlet hose to drill and water source.
NOTE! Vacuum can be released by turning vacuum
release valve (Figure 2).
NOTE! Water can be supplied by a standard garden
hose or by a pressure tank. Water is fed through
inlet hose, down inside of bit, washing cuttings
from under bit crown, up and outside of hole. Be
sure that any method used has adequate water
pressure to supply a flow of 1-2 gallons per
minute. Lack of water can cause diamonds to
polish or burn the bit causing bit end to turn blue.
Ceiling Jack Anchor Method
1. Cut pipe or wood to the required length to fit be-
tween ceiling and ceiling jack screw (Figure 1) on
top of mast.
2. Tighten ceiling jack screw to force machine against
floor.
5. With drill motor ON/OFF switch in OFF position, plug
power cord into a properly grounded receptacle.
3. Stabilize and plumb machine by adjusting 4 leveling
screws on base.
6. Open water control valve allowing water to flow at 1-
2 gallons per minute.
Operating Instructions
WARNING
Before turning drill motor ON, be certain
WARNING!
that machine is securely anchored.
7. Turn drill motor ON/OFF switch to ON position.
CAUTION
DO NOT apply full load until entire bit
crown has penetrated the material.
8. Turn feed handle to apply load on bit. To prevent bit
from wandering, apply light pressure on feed handle
while starting to drill.
Do not wear cloth gloves or loose clothing when
operating Drilling Machine. Keep sleeves and jack-
ets buttoned. Do not reach across the machine.
Keep hands and fingers away from drill bits.
NOTE! The AMP-meter has a green and red area to in-
dicate proper pressure and drilling speed,
preventing motor overload and providing longer
bit life. The green area is the working range;
the red area indicates too much pressure being
applied. Keep Amp-meter needle in the green
area. Too little pressure can polish bit and too
much can cause undue wear.
Do not use this Drilling Machine if the ON/OFF
switch or other controls are broken. Always wear
eye protection to protect eyes from dirt and other
foreign objects.
Do not use Drilling Machine if it is not securely an-
chored.
9. Drill bit feed should be uniform without excessive
force. Drilling penetration of 1″ to 4″ per minute may
be achieved in concrete depending on material and bit
diameter. Proper feed pressure is determined by load
on motor and reading on Amp-meter. To maximize life
of drill bit, regulate feed rate so that needle on Amp-
meter is in upper green area of 20 amp range. If
needle goes into red area above 20 amps, decrease
feed rate as undue bit wear will result.
1. Thread the drilling bit (Figure 4) onto drilling spindle
(Figure 1) and tighten securely with bit wrench.
CAUTION
Never turn drill ON with bit resting on
the concrete.
2. Check hole alignment by lowering drill until it is about
1
2
/ ″ from concrete.
3. Position 2-speed selector knob on drill to desired
speed. Move selector down towards spindle to select
high speed for up through 4″ bits. Move selector
up away from spindle to select low speed for bits
NOTE! If the cooling water turns clear, it is an indication
you are drilling through rebar.
Ridge Tool Company
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
10. Your control panel amp-meter will go into the red
area when you hit steel. When you encounter rebar,
lessen feed feed rate to allow needle to return to the
green area.
Installing Bit Extension Rods
In order to drill deeper than the 13″ long bit will allow, bit
extension rods must be used. Drilling rate will be slower
because of the extra amount of drag on the bit walls.
NOTE! It is recommended that after cutting steel, you
stop and break out core and any loose pieces of
steel, then proceed.
NOTE! When it is necessary to place the drilling ma-
chine above the surface being drilled, do not
use a bit extension rod that is longer than 12″.
CAUTION
When drilling steel embedded in con-
1. Drill to full depth of bit.
crete, never switch to HIGH speed if you are drilling in
LOW speed. These bits are not designed to drill through
solid steel.
2. Back drill out and remove bit and core.
3. Put drill bit back into hole and connect a 4, 6 or 12″ bit
WARNING
Use extreme care when drilling through
extension rod to bit and secure with spindle wrench.
floors. Provide for protection of all personnel and mate-
rial below the area. Cores generally drop from drill bit at
completion of the hole.
4. Screw bit extension rod onto drill spindle and secure
with spindle wrench.
5. Proceed with drilling.
Removing Cores
Breaking a Core
Accessories
1. If you are not drilling completely through, the core can
be easily broken by inserting a screwdriver into the
drilled groove and prying the core to the opposite side.
WARNING
Only the following RIDGID products have
been designed to function with the Core Drilling Machine.
Other accessories designed for use with other tools may
become hazardous when used on this machine. To pre-
vent serious injury, use only the accessories listed below.
2. Use a second screwdriver to lift core out.
Removing Broken Core Below the Surface
Accessories for Core Drilling Machines
Small Anchor Base (7″ x 12″)
1
8
1. Use a / inch diameter steel rod.
1
4
2. Make a / inch long 90° bend at one end.
Anchor-Vacuum Base (13″ x 17″)
Anchor-Vacuum Drill Stand
3. Insert rod down side of broken core to depth of break,
twist 90° and lift core out.
Vacuum Motor (115V) 60Hz
Vacuum Motor (230V) 50Hz Export
Vacuum Motor with Fittings (115V) 60Hz
Vacuum Motor with Fittings (230V) 50Hz
Control Panel (115V)
Removing Broken Core Stuck In Bit
WARNING
Unplug machine cord from power source.
1. Increase water pressure and try to free core with
your hands.
Control Panel (230V)
2. If unable to free core, remove bit from drill.
2″ Spacer Block (Applications Over 10″)
20 Amp (115V) 25-60Hz, 450/1200 RPM Motor
10 Amp (230V) 25-60Hz, 4501200 RPM Motor
Spindle Wrench
3. Push core gently through from top of bit with a rod
using a capped bit.
Removing a Lodged Bit from Hole
Water Collector & Pump (115V)
Water Collector & Pump (230V)
Water Collector Ring
WARNING
Unplug machine cord from power source.
1. Turn Water ON.
Water Pump (115V) 50-60Hz
2. Using bit wrench, try to rotate bit in both directions and
lift out using feed handle.
Water Pump (230V) 50-60Hz
3. If unable to free bit, turn water OFF and disconnect bit
from drill spindle. Use bit wrench again, rotating back
and forth and rocking until free.
NOTE! See Ridge Tool catalog or a Ridge distributor for
a complete list of Core Drill Bits, Adapters and
Bit Extensions.
8
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Maintenance Instructions
Service and Repair
WARNING
Make sure machine is unplugged from
power source before performing maintenance or making
any adjustment.
WARNING!
Lubrication
Keep a light coating of oil on rack and pinion and drill
spindle.
Ventilation
Keep drill motor inlet and air passage clear to assure
proper motor ventilation.
Service and repair work on this Core Drilling Machine
must be performed by qualified repair personnel.
Machine should be taken to a RIDGID Independent
Authorized Service Center or returned to the factory. All
repairs made by Ridge service facilities are warranted
against defects in material and workmanship.
Motor Brush Replacement
Check motor brushes every 200 hours and replace when
brushes become / inch or less in length.
1
4
When servicing this machine, only identical replace-
ment parts should be used. Failure to follow these
instructions may create a risk of electrical shock or
other serious injury.
Bit Replacement
Bit is considered worn when the crown shows excessive
wear and has become flush with tube.
If you have any questions regarding the service or repair
of this machine, call or write to:
Ridge Tool Company
Technical Service Department
400 Clark Street
Elyria, Ohio 44035-6001
Tel: (800) 519-3456
E-mail: [email protected]
Shims
Carriage head will become loose due to vibrations.
Tighten shim adjusting screws to remove play.
Vacuum Seal
Replace vacuum seal if it becomes mushroomed on
bottom edge, cracked, pitted, or worn.
For name and address of your nearest Independent
Authorized Service Center, contact the Ridge Tool
Machine Storage
Motor-driven equipment must be kept indoors or well cov-
ered in rainy weather. Always remove vacuum seal from
base of machine. Store the machine in a locked area that
is out of reach of children and people unfamiliar with
drilling machines. This machine can cause serious injury
in the hands of untrained users.
Ridge Tool Company
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Wiring Diagram (115V, 60Hz)
12 GA (Black)
14 GA (Black)
Vacuum
Receptacle
15 Amp
B
B
Motor
Receptacle
20 Amp
Vacuum
Switch
16 Amp
125 Volt
125 Volt
Motor
Switch
20 Amp
125 Volt
Amp-Meter w/Current
Transformer
125 Volts
GR
W
W
14 GA (Black)
12 GA (Black)
14 GA (White)
12 GA (Green)
14 GA (Green)
12 GA (White)
12 GA (Green)
To Box
Twistlock Plug
30 Amp 125 Volt
Wiring Diagram (230V, 50-60Hz) - Australia and Europe
Black
White
Black
Black
Ammeter
White
Motor
Receptacle
20 Amp
Motor
250V AC
Vacuum
Switch
Vacuum
Receptacle
15 Amp
Switch
10 Amp
250V AC
GRD
8 Amp
GRD
250V AC
250V AC
White
Black
Brown
Blue
250V AC
Filter
Green/Yellow
Green/Yellow
10
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
Wiring Diagram (230V, 50-60Hz) - Cat. No. 16597
Black
White
Black
Black
White
Ammeter
Motor
Receptacle
20 Amp
250V AC
Vacuum
Receptacle
15 Amp
Motor
Switch
10 Amp
250V AC
Vacuum
Switch
8 Amp
GR
250V AC
GR
250V AC
Black
White
Green/Yellow
Blue
Brown
250V AC
Green
Green/Yellow
Filter
Ridge Tool Company
11
Download from Www.Somanuals.com. All Manuals Search And Download.
RB-214/215 Core Drilling Machine
12
Ridge Tool Company
Download from Www.Somanuals.com. All Manuals Search And Download.
FULL LIFETIME
FULL LIFETIME
WARRANTY
WARRANTY
Against Material Defects
Against Material Defects
&
Workmanship
&
Workmanship
What is covered
Ce qui est couvert
®
®
RIDGID tools are warranted to be free of defects in workmanship and material.
Les outils RIDGE sont garantis contre tous vices de matériaux et de main d’oeuvre.
Durée de couverture
How long coverage lasts
This warranty lasts for the lifetime of the RIDGID tool. Warranty coverage ends when the prod-
®
®
Cette garantie est applicable durant la vie entière de l’outil RIDGE . La couverture cesse dès lors que
le produit devient inutilisable pour raisons autres que des vices de matériaux ou de main d’oeuvre.
uct becomes unusable for reasons other than defects in workmanship or material.
Pour invoquer la garantie
How you can get service
Pour toutes réparations au titre de la garantie, il convient d’expédier le produit complet en port payé
à la RIDGE TOOL COMPANY, Elyria, Ohio, ou bien le remettre à un réparateur RIDGID agréé. Les
clés à pipe et autres outils à main doivent être ramenés au lieu d’achat.
To obtain the benefit of this warranty, deliver via prepaid transportation the complete product
to RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID INDEPENDENT SERVICE
CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase.
®
®
Ce que nous ferons pour résoudre le problème
What we will do to correct problems
Les produits sous garantie seront à la discrétion de RIDGE TOOL, soit réparés ou remplacés, puis
réexpédiés gratuitement ; ou si, après trois tentatives de réparation ou de remplacement durant
la période de validité de la garantie le produit s’avère toujours défectueux, vous aurez l’option de
demander le remboursement intégral de son prix d’achat.
Warranted products will be repaired or replaced, at RIDGE TOOL’S option, and returned at no
charge; or, if after three attempts to repair or replace during the warranty period the product
is still defective, you can elect to receive a full refund of your purchase price.
What is not covered
Ce qui n’est pas couvert
Les défaillances dues au mauvais emploi, à l’abus ou à l’usure normale ne sont pas couvertes par
cette garantie. RIDGE TOOL ne sera tenue responsable d’aucuns dommages directs ou indirects.
Failures due to misuse, abuse or normal wear and tear are not covered by this warranty. RIDGE
TOOL shall not be responsible for any incidental or consequential damages.
How local law relates to the warranty
L’influence de la législation locale sur la garantie
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
rights, and you may also have other rights, which vary, from state to state, province to
province, or country to country.
Puisque certaines législations locales interdisent l’exclusion des dommages directs ou indirects,
il se peut que la limitation ou exclusion ci-dessus ne vous soit pas applicable. Cette garantie vous
donne des droits spécifiques qui peuvent être éventuellement complétés par d’autres droits
prévus par votre législation locale.
No other express warranty applies
This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID products. No
employee, agent, dealer, or other person is authorized to alter this warranty or make any other
warranty on behalf of the RIDGE TOOL COMPANY.
Il n’existe aucune autre garantie expresse
®
Cette GARANTIE PERPETUELLE INTEGRALE est la seule et unique garantie couvrant les produits
®
RIDGID . Aucun employé, agent, distributeur ou tiers n’est autorisé à modifier cette garantie ou à
offrir une garantie supplémentaire au nom de la RIDGE TOOL COMPANY.
FULL LIFETIME
WARRANTY
Against Material Defects
&
Workmanship
Ridge Tool Company
400 Clark Street
Elyria, Ohio 44035-6001
Qué cubre
Las herramientas RIDGID están garantizadas contra defectos de la mano de obra y de los
materiales empleados en su fabricación.
Duración de la cobertura
Esta garantía cubre a la herramienta RIDGID durante toda su vida útil. La cobertura de la
garantía caduca cuando el producto se torna inservible por razones distintas a las de defectos
en la mano de obra o en los materiales.
Cómo obtener servicio
Para obtener los beneficios de esta garantía, envíe mediante porte pagado, la totalidad del pro-
ducto a RIDGE TOOL COMPANY, en Elyria, Ohio, o a cualquier Servicentro Independiente
RIDGID. Las llaves para tubos y demás herramientas de mano deben devolverse a la tienda donde
se adquirieron.
Lo que hacemos para corregir el problema
El producto bajo garantía será reparado o reemplazado por otro, a discreción de RIDGE TOOL,
y devuelto sin costo; o, si aún resulta defectuoso después de haber sido reparado o sustituido
tres veces durante el período de su garantía, Ud. puede optar por recibir un reembolso por el valor
total de su compra.
Lo que no está cubierto
Esta garantía no cubre fallas debido al mal uso, abuso o desgaste normal. RIDGE TOOL no se
hace responsable de daño incidental o consiguiente alguno.
Relación entre la garantía y las leyes locales
Algunos estados de los EE.UU. no permiten la exclusión o restricción referente a daños inci-
dentales o consiguientes. Por lo tanto, puede que la limitación o restricción mencionada
anteriormente no rija para Ud. Esta garantía le otorga derechos específicos, y puede que,
además, Ud tenga otros derechos, los cuales varían de estado a estado, provincia a provincia o
país a país.
No rige ninguna otra garantía expresa
Ridge Tool Subsidiary
Emerson Electric Co.
Esta GARANTIA VITALICIA es la única y exclusiva garantía para los productos RIDGID. Ningún
empleado, agente, distribuidor u otra persona está autorizado para modificar esta garantía u ofre-
cer cualquier otra garantía en nombre de RIDGE TOOL COMPANY.
Printed in U.S.A. 2/01
999-998-024.10
Download from Www.Somanuals.com. All Manuals Search And Download.
|