U N I V E R S A L
REMOTE
• Consolidates up to 5
component remotes!
• Long range
RF transmitter
for select
satellite systems
• Comfortable
grip & keypad
layout promotes
ease of use
TV
CABLE BOX
VCR
DVD PLAYER
DBS SYSTEM
AUDIO SYSTEM
Compatible with most
brands of components.
D770
*See compatibility on back
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Description
ANTENNA In TV Mode, lets you
switch the source of the video signal
from satellite signals to an off-air
antenna
or cable signal when using the OUT
TO TV jack. In VCR Mode, it functions
as a TV/VCR input key.
ARROWS Use the navigation arrows
to move the on-screen highlight up,
down, left, or right. Using the arrows
to highlight a menu item is also
called “pointing.”
CH + (UP)/ - (DOWN) Use to scan up and
down through the channels in the current
channel list. If you are in the program
guide or menu system, use the CH +/-
keys to page up and down a screen at a
time. You can also use the CH +/- keys on
the top of the digital satellite receiver to
change the channel.
CLEAR Removes the on-screen displays
and returns you to normal viewing.
COMPONENT KEYS When
programmed, these keys are used to put
the remote in a specific mode so that it
can control that component.
AUX1 and AUX2 Act as “wildcard”
keys. They can be programmed to
control another TV, VCR, DVD,
satellite receiver, cable box, or an audio
component. Follow the direct entry
programming instructions on page 7 to
program these keys.
Note: The AUX1 key is pre-programmed with
codes to control a Dish Network digital
satellite receiver.
DVD Puts the remote in DVD Mode.
SAT Puts the remote in SAT Mode. This key is pre-programmed
to control an RCA DIRECTV® digital satellite receiver manufactured
before 2004.
Note: This key cannot be reprogrammed. If the SAT key doesn’t control your
receiver, use the AUX1 key to program the remote to control your satellite receiver
if it was purchased after 2003.
TV Puts the remote in TV Mode.
VCR Puts the remote in VCR Mode.
Digit Keys (0-9) Use the digit keys to tune directly to a three-digit
satellite channel or non-satellite channel. If a satellite channel number is
less than four-digits long, you must press OK after entering the channel
number. If you are in the menu system, use the digits to highlight and
select items. Use 0 to return to the previous menu screen.
FETCH Either brings up the Fetch menu or tells the receiver to take the
action you programmed it to take.
GO BACK Moves you back and forth between the last two selected
channels. In the menu system, returns you to the previous screen.
GUIDE Brings up the program guide. Subsequent presses of the GUIDE
key switch between the Detail and Grid guide formats.
INFO Brings up the on-screen channel banner, password challenge, or
purchase offer screen. Press again to get program details. In the
program guides, press INFO to get information about the highlighted
program or channel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Description (Continued)
LED indicator light This light turns red at each valid key press. When
programming the remote control, it flashes or turns on or off to indicate
programming status.
MENU Displays the Main menu. If you are already in the menu system,
press OK or MENU to select a highlighted choice. When you are using
the remote control to operate an RCA, GE, or PROSCAN VCR (the
remote is in VCR mode), the MENU key functions as a PROGRAM key.
MUTE Reduces the TV’s volume to its minimum level. Press again to
restore the volume.
OK Selects a highlighted choice if you are in the menu system. After
entering a one-, two-, or three-digit satellite channel number, press to
tune to the channel. If you are entering a number other than a satellite
channel number (for instance, to tune your VCR to a channel), you do
not need to press this key. Press the OK key when the Interactive TV
icon (¿) appears on the screen. Pressing OK will display more
information and offer the chance to interact in some way with
what is displayed on screen.
ON•OFF Turns the component you are controlling on or off. When
pressed twice within two seconds, all components that are on will be
turned off. This feature only works with most RCA, GE, and PROSCAN
products. You can also use the ON•OFF key on the top (front panel) of
the digital satellite receiver to turn off the receiver.
SKIP This key is not used by the digital satellite receiver. It is functional
only with RCA, GE, PROSCAN TVs and VCRs.
Transport Keys (REVERSE, PLAY, FORWARD, RECORD, STOP,
PAUSE) When programmed, these keys are used to control an auxiliary
component, such as a VCR or DVD player. Note: If your VCR is connected,
the RECORD key can be used to schedule a timed recording when using
the Program Guide or to begin recording while watching a program (in
VCR Mode).
VOL + (UP)/ - (DOWN) Adjusts the audio volume of your TV.
WHO•INPUT Press the WHO key one or more times to scroll through
the user profiles. When you are using the remote control to operate an
RCA, GE, or PROSCAN TV (in TV Mode), press the WHO•INPUT key
one or more times to scroll through the available video input sources.
Programming The Remote Control
The remote is already programmed to control most RCA, GE, and
PROSCAN branded components; it may need to be programmed to
control other manufacturers’ brands.
Testing The Remote Control To determine whether the universal
remote control needs to be programmed, turn on a component, such as
a VCR, point the remote at the VCR, and press the VCR key. Then press
ON•OFF or CH + or CH - to see if the VCR responds to the remote
commands. If it does not respond, the remote needs to be programmed.
There are two ways to program the remote control: Automatic Code
Search or Direct Entry.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming For TV—Direct Entry Method
(OFF)
1.
Manually turn on the TV.
2. Locate the enclosed TV Code List. Find
your brand of TV.
3. Press and hold the TV key.
4.
Enter a code from the code list.
(OFF)
5. Release the TV key, and then press
ON•OFF to see if the TV responds to
the remote control commands. If it
doesn’t, try pressing the TV key and
then ON•OFF again.
6. If you get no response, repeat these steps
using the next code listed for your brand
until the TV responds to the remote
control commands.
TV CODE
7.
Enter your code here for easy reference.
Programming For VCR—Direct Entry Method
(OFF)
1.
Manually turn on the VCR.
2. Locate the enclosed VCR Code List.
Find your brand of VCR.
3.
4.
5.
Press and hold the VCR key.
Enter a code from the code list.
Release the VCR key, then press
ON•OFF to see if the VCR responds
to the remote control commands. If
it doesn’t, try pressing the VCR key
and then ON•OFF again.
(OFF)
6. If you get no response, repeat these
steps using the next code listed
for your brand until the VCR responds
to the remote control commands.
VCR CODE
7.
Enter your code here for easy reference.
Programming For DVD—Direct Entry Method
1.
Manually turn on the DVD player.
(OFF)
2. Locate the enclosed DVD Code List.
Find your brand of DVD player.
3.
4.
5.
Press and hold the DVD key.
Enter a code from the code list.
(OFF)
Release the DVD key, and then
press ON•OFF to see if the DVD
responds to the remote control
commands. If it doesn’t, try pressing
the DVD key and then ON•OFF again.
6.
7.
If you get no response, repeat these
steps using the next code listed for
your brand, until the DVD responds
to the remote control commands.
DVD CODE
Enter your code here for easy reference.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming The AUX1 And AUX2 Keys
You can assign any one of the following components to the AUX1
or AUX2 keys:
A second TV, VCR, DVD, satellite system, cable box, or an
audio component.
Note: The AUX1 key is pre-programmed with codes to control Dish Network digital
satellite receivers. The SAT key is pre-programmed with codes to control RCA
DIRECTV digital satellite receivers. If you wish to control a second RCA DIRECTV
digital satellite receiver, program the AUX1 or AUX2 key with satellite code 5001.
Then refer to your RCA DIRECTV satellite receiver manual for instructions on
remote control setup.
1. Manually turn on the component you wish to control.
Find the four-digit code for the component
you wish to program in the code list.
2. Press and hold the AUX1 or AUX2 key.
(OFF)
While holding the AUX1 or AUX2 key,
press the first number of the component
code. If the first number is valid, the
LED will turn off.
3. Enter the code using the DIGIT (0–9) keys.
After your full code is entered, the LED
light will turn on to verify that the code
entered is valid. Release the component
(OFF)
key. The LED will go off.
Note: If the code is invalid, the LED light will flash
four times and the remote will revert back to
normal operation maintaining the current code.
4. Aim the remote at the component you
wish to control and press the ON•OFF
key. The component should turn off.
Note: If the component you have programmed
does not respond, try all the codes for
your brand. If the codes do not work, or
your brand is not listed, try the Automatic
Code Search method on pages 8.
5. With your component on, press
CH+ (CHANNEL UP) or the ON•OFF
key. If the component responds,
OR
no further programming is required.
6. Enter your code here and then check
the type of component you programmed
for easy reference.
AUX1 CODE
AUX2 CODE
TV VCR DVD CABLE SAT AUDIO
TV VCR DVD CABLE SAT AUDIO
✓
✓
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Automatic Code Search
The following instructions can be used to program the remote to control
the TV, VCR or DVD. If you want to exit the automatic code search
without programming any of your components, press the CLEAR key
until the LED (red light) turns off.
1. Turn on the component you want to control (TV, VCR
or DVD).
2. Press and hold the component key you want to program.
While holding the component key, press and hold ON•OFF
until the LED on the remote control turns on, then release
both keys.
Note: The AUX1 and AUX2 keys can only be programmed using Direct Entry Mode.
See page 7 for details.
3. Point the remote at the component, press and release PLAY, then wait
five seconds or until the LED stops flashing.
At this point the remote control is searching for the correct code to
program. If, after five seconds, the component you want to control
does not turn off, press and release PLAY again to tell the remote to
search the next set of codes.
Continue pressing and releasing PLAY until the component turns off
or you have searched through all of the codes. There are 20 sets of
codes. If the component does not turn off after pressing PLAY 20
times, then the remote cannot control that particular component.
If the component you want to control does turn off:
1. Press and release REVERSE, then wait two seconds.Repeat this step
until the component turns back on.
2. To finish, press and hold STOP until the LED on the remote control
turns off.
Using The Remote To Control A Component
Because this universal remote can control several different components
(TV, VCR, DVD, etc.), it uses operational modes triggered by the
component keys. For example, if you want the remote to control the TV,
you would press the TV key to put the remote into TV Mode. Then, if
you want to play a videotape, press VCR then PLAY (pointing the
remote at the VCR).
Changing The RF Remote Control Code
Your remote control is equipped with RF functionality. This means
that the remote can control the digital satellite receiver using both IR
(infrared) signals and RF (radio frequency) signals if it is equipped with
an RF receiver. IR signals require line-of-sight to the receiver’s front
panel remote sensor. RF signals can control the receiver from other
parts of your house, even through walls. Installing your RF remote
control antenna will increase the range of your RF remote signal. See
the owner’s manual of your DBS system for more details.
Note: This feature is only applicable for RCA DIRECTV digital satellite receivers.
If you are experiencing interference from other RF components, you
may need to change the RF remote control code. To change the code
first in your satellite receiver, do the following:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing The RF Remote Control Code (Continued)
1. Select Options in the Main menu.
2. Select System Options.
3. Select RF Remote.
4. If you normally use the SAT key on your remote to control your RCA
satellite receiver, choose a number between 000 and 255. Follow the
on-screen instructions to enter this number as your RF remote control
code. However, if you use the AUX1 or AUX2 key, choose a number
between 000 and 099.
Then, to change the code on your remote to match the satellite receiver,
perform the following:
1. Press and hold the SAT key, AUX1, or AUX2 key (depending on
which key you use to control your satellite receiver).
2. Then use the Digit keys to enter the same RF remote control
code (000-255 for SAT), or (000-099 for AUX1 or AUX2) on your
remote control.
Menu Function
The Menu function is used to make changes in the selected settings,
such as setting color, channels, timer, etc. The MENU key displays TV,
DVD player, and DBS menu screens on your TV. Each Menu function
will vary from brand to brand.
ENTERING THE MENU MODE
1. Push the component key on the
remote for the desired menu screen.
2. Push the MENU key. This allows you
to view the menu of the chosen
component. The menu should
(BLINK)
now be visible on your television.
Note: With some brands you may have to press
the GUIDE or INFO key for the on-screen menu.
3. While in MENU Mode, these
keys will function as follows:
Navigation LEFT/RIGHT keys will
operate as cursor right and left.
Navigation UP/DOWN keys will
operate as cursor up and down.
OR
MENU or OK key applies the
highlighted menu item.
Not all functions in all models and
brands of equipment may be fully supported.
EXITING THE MENU MODE
To exit the MENU Mode and clear the
screen on your TV, push the CLEAR key.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem: The remote can’t be
programmed to operate your
component.
Problem: The remote does not operate
your component.
•
You must put the remote in the
correct mode by pressing the
corresponding component key (TV,
VCR, DVD, SAT, AUX1, AUX2) so
the remote knows which component
you want to operate.
•
You may be too far away from the
component or at a wrong angle. This
remote uses IR (infrared) technology
to communicate with components.
The remote sends the code and the
component’s IR sensor reads the
code. Therefore, there must be an
unobstructed path between the
remote and the IR sensor on the
component. Move closer and make
sure you point the remote at the
component (VCR when
•
Remove any obstacles between the
remote and the component. Make
sure to aim the remote at the IR
sensor on the component.
•
•
•
Make sure the batteries are properly
installed. (See Battery Installation
on page 3).
programming the VCR key; DVD
when programming the DVD key;
TV when programming the TV key;
satellite receiver when programming
the SAT key).
Replace the batteries with two new
AA batteries. Reprogramming may
be required.
Reset the remote. Remove the
batteries. Then press and hold
the number 1 key on the remote
for several seconds to reset the
microprocessor inside the remote.
Release the number 1 key, reinstall
the batteries, and try the remote
again. Reprogramming will
be required.
•
•
•
If you’ve entered all of the codes
for your brand that are in the
enclosed Code Lists and followed
the instructions, try the Automatic
Code Search method (See Using
Automatic Code Search on page 8).
You must put the remote in the
correct mode by pressing the
corresponding component key (TV,
VCR, DVD, SAT, AUX1, AUX2) so
the remote knows which component
you want to operate.
Problem: The remote is not
performing commands properly.
•
You must put the remote in the
correct mode by pressing the
corresponding component key (TV,
VCR, DVD, SAT, AUX1, AUX2) so
the remote knows which component
you want to operate.
To program the universal remote
to operate a combination unit
(TV/VCR or TV/DVD), first try the
VCR or DVD codes for your brand.
Some units, however, require that
you program both the TV (using the
TV codes) and the VCR or DVD
(using the VCR or DVD codes) for
full operation.
•
•
Make sure the component is “ready”
(e.g., DVD player has disc loaded;
VCR has tape loaded, etc.).
You may have pressed an invalid
key for the mode the remote is in
(e.g., the RECORD key only works
in VCR Mode).
•
To program the universal remote
to operate a combination unit (VCR
/DVD), first program your VCR
using the VCR key and then program
your DVD using the DVD key.
•
•
•
If you are trying to turn on an RCA,
GE or PROSCAN component, press
the component key (TV, VCR, DVD,
SAT, AUX1, AUX2) instead of the
ON·OFF key.
Problem: The indicator light does
not light when you press a key.
If you’re trying to change channels,
try pressing the OK key after
entering the channel number as this
is a requirement of certain models
and brands.
•
You must put the remote in the
correct mode by pressing the
corresponding component key
(TV, VCR, DVD, SAT, AUX1, AUX2)
so the remote knows which
component you want to operate.
There is a possibility that a
programmed code may only be able
to control some of your component
features (e.g., only turns a
•
You may have pressed an invalid
key for the mode the remote is in
(e.g., the RECORD key only works
in VCR Mode).
component on and off). Follow the
steps provided for programming the
remote (See Programming sections
on pages 5–7). If the component can
be turned on and off, make sure you
press the CH+/CH- key to see if the
component responds. If not, try the
next code from the list.
•
•
Make sure the batteries are properly
installed. (See Battery Installation
on page 3).
Replace the batteries with two new
AA batteries. Reprogramming may
be required.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
Problem: The VCR won’t record.
Problem: The component’s menu
doesn’t appear on the TV screen.
•
As a safety feature, you must
press the RECORD key twice to
begin recording.
•
The TV must be tuned to the Video
Input that matches the manner in
which you connected the
•
•
Make sure the tape is properly
loaded in the VCR.
component to the TV.
For example, if you connected your
DVD player to your TV by
Make sure the tape is not
write-protected. If the safety tab
is removed, the tape is write-
protected and you cannot record
onto that tape.
connecting audio/video cables
(usually color-coded yellow, red and
white) to the TV’s Input 1 jack, you
must tune the TV to its Video 1
Input channel. Remember, different
manufacturers label these jacks
differently. Consult the instruction
manual that came with the TV for
more information.
Problem: The remote will not change
channels.
•
You must put the remote in the
correct mode by pressing the
corresponding component key
(TV, VCR, DVD, SAT, AUX1, AUX2)
so the remote knows which
•
•
You must put the remote in the
correct mode by pressing the
corresponding component key (TV,
VCR, DVD, SAT, AUX1, AUX2) so
the remote knows which component
you want to operate.
component you want to operate.
•
Press the OK key after you enter a
channel number.
Menu access isn’t supported for
all brands. If that’s the case, you
need to use your original remote
control to access menu functions
for these components.
Questions
Please visit www.rca.com
Limited Lifetime Warranty
Our company (in the U.S., THOMSON INC. / In Canada, Thomson
multimedia Ltd.) will replace this product, regardless of how long
you, the original purchaser, own it if found to be defective in
materials or workmanship. For a prompt, no charge replacement of
equivalent product, return the defective product postage prepaid to
the appropriate address.
In the US:
Product Exchange Center
11721 Alameda Avenue
Socorro TX 79927
In Canada:
Thomson multimedia Ltd.
6200 Edwards Boulevard
Mississauga, Ontario
Canada L5T 2V7
This replacement is the company's sole obligation under this
warranty. THOMSON INC. / Thomson multimedia Ltd. will not be
responsible for any incidental or consequential damages or for any
loss arising in connection with the use or inability to use this product.
Some states/provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty excludes defects or
damage due to misuse, abuse, or neglect. This warranty gives you
specific legal rights, and you may also have other rights, which vary
from state to state/province to province.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Consolidate Five Remote Controls Into One!
Updated code library now includes codes for Dish Network satellite receivers
Dedicated Guide, Fetch and Who keys for use with your digital satellite system
Compatible with the latest technology
•
•
•
* Your RCA universal remote control is compatible with most brands of infrared remote-controlled
components manufactured after 1990. Some well-known brands are shown below. The complete list of
brands is found on the Code List inside this package. The remote already operates most RCA, GE and
PROSCAN products without any programming!
TV
VCR
DVD
CABLE
Aiwa
Allegro
Apex
Broksonic
Daewoo
Emerson
Funai
ABC
Abex
Adventura
Aiko
Aiwa
Optimus
Optonica
Orion
Panasonic
Philco
Philips
Pilot
Pioneer
Portland
Price Club
Prima
Prism
PROSCAN
Proton
Pulsar
Quasar
RadioShack
RadioShack/R
ealistic
RCA
Runco
Sampo
Samsung
Sansui
Sanyo
Scotch
Scott
Sears
Sharp
Shogun
Signature
Simpson
Sony
Soundesign
Squareview
SSS
Starlite
Supre-Macy
Supreme
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Technics
Techwood
Teknika
Telecaption
Tera
Pentex
Antronix
Archer
Admiral
Adventura
Aiko
Akai
Alleron
Amtron
Anam
National
AOC
Apex
Research
Philco
Philips
Pilot
Pioneer
Portland
PROSCAN
Protec
Pulsar
Quarter
Quartz
Quasar
RadioShack
RadioShack/
Realistic
Radix
Randex
RCA
Realistic
Ricoh
Runco
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Shogun
Singer
Sony
Cabletenna
Cableview
Century
Citizen
Colour Voice
Comtronics
Contec
Eastern
Garrard
GC
Electronics
GE
Gemini
General
Instruments
Hamlin
Hitachi
Jasco
Akai
Allegro
American High
Asha
Audio
Dynamics
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
Candle
Canon
Capehart
Carver
CCE
Citizen
Colortyme
Colt
GE
Go Video
Hitachi
JBL
JVC
Kenwood
Konka
Audiovox
Belcor
Bell & Howell
Bradford
Broksonic
Brokwood
Candle
Celebrity
Centurion
Citizen
Colortyme
Concerto
Contec/Cony
Craig
Crosley
Crown
Curtis Mathes
CXC
Daewoo
Daytron
Dimensia
Dumont
Dynatech
Electroband
Electrohome
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretec
GE
Gilbralter
Goldstar
Grundy
Hallmark
Harvard
Hisense
Hitachi
IMA
Infinity
Janeil
JBL
JCB
JC Penney
Jensen
Koss
Lasonic
Magnavox
Memorex
Mintek
Mitsubishi
NAD
Onkyo
Oritron
Panasonic
Philips
Pioneer
PROSCAN
Qwestar
RCA
Samsung
Sansui
Sanyo
Sharp
Sony
Sylvania
Toshiba
Venturer
Yamaha
Zenith
Jerrold
Magnavox
Memorex
Motorola
Movie Time
NEC
NSC
Oak
Panasonic
Philips
Pioneer
PROSCAN
RCA
Realistic
Regal
Regency
Rembrandt
Samsung
Scientific
Atlanta
Signal
Signature
Sprucer
Standard
Component
Starcom
Stargate
Starquest
Tocom
Craig
Curtis Mathes
Cybernex
Daewoo
Daytron
DBX
Dimensia
Dynatech
Electrohome
Electrophonic
Emerson
Fisher
Fuji
Funai
Garrard
GE
Go Video
Goldstar
Gradiente
STS
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Teknika
TMK
Toshiba
Totevision
Unitech
Vector
Research
Victor
Video
Concepts
Videosonic
Wards
XR-1000
Yamaha
Zenith
Harley
Davidson
Harman
Kardon
CD
ADC
ADO
Aiwa
Akai
Denon
Dynatech
Emerson
Fisher
GE
Hitachi
Inkel
Harwood
Headquarter
Hi-Q
Hitachi
Instant Replay
JCL
JC Penney
Jensen
JVC
Kenwood
KLH
Kodak
LG
Lloyd's
Logik
LXI
Magnavox
Magnin
Marantz
Marta
Matsushita
MEI
Memorex
MGA
MGN
Technology
TMK
Tusa
TV86
Unika
United Cable
Universal
Video Way
View Star
Zenith
Toshiba
Totevision
Universal
Victor
Vidtech
Viking
Wards
White
Westinghouse
JVC
Kenwood
Luxman
Marantz
MCS
Mitsubishi
Nakamichi
NEC
Onkyo
Optimus
Panasonic
Pioneer
RCA
Sanyo
Sears
Sherwood
Sony
Teac
JVC
SATELLITE
Kawasho
Kenwood
KLH
Yamaha
Zenith
Alphastar
Chaparral
DIRECTV
Dish Network
Drake
Echostar
Express Vu
GE
General
Instruments
Hitachi
Hughes Network
Systems
JVC
Magnavox
Motorola
Panasonic
Philips
Primestar
PROSCAN
RCA
Realistic
Sony
Star Choice
STS1
STS2
STS3
STS4
Toshiba
Uniden
Kloss
Novabeam
KTV
LG
Loewe
Logik
Luxman
LXI
Magnavox
Majestic
Marantz
Megatron
Memorex
MGA
Midland
Minutz
Mitsubishi
AUDIO
Aiwa
Denon
Harman
Kardon
JBL
JVC
Kenwood
Koss
Onkyo
Optimus
Panasonic
Philips
Pioneer
RCA
Sherwood
Sony
Technics
Venturer
Yamaha
Midland
Minolta
Mitsubishi
Montgomery
Ward
Motorola
MTC
Multitech
NEC
Technics
Toshiba
Yamaha
Montgomery
Ward
Nikko
Motorola
MTC
Multitech
Multivision
NAD
NEC
Nikko
Noblex
Olympus
Optimus
Optonica
Orion
Panasonic
Pentax
NTC
Onwa
®
* NOTE: The SAT key is preprogrammed to control an RCA DIRECTV
digital satellite receiver manufactured before 2004.
Requires two AA batteries (sold separately)
©2005 THOMSON INC.
10330 North Meridian Street
Indianapolis IN 46290
Made In Mexico
D770
D770 US IB REV C
TOMCOM16490560
Trademark(s) ®Registered Marca(s) Registrada(s)
Download from Www.Somanuals.com. All Manuals Search And Dwowwwn.rlocaa.cdo.m
|