User’s Manual
Free To Air
VS2000
Digital Satellite Receiver
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instruction
1) Read all of these instructions.
2) Save these instructions for later use.
3) Follow all warnings and instructions marked on the product.
4) Follow all instructions.
5) Do not use the apparatus near water.
6) Clean only with dry cloth.
Declaration of Conformity
7) Do not block any ventilation openings. Install in accordance with the manufacturerís instructions.
8) Do not install near any heat sources such as radiators. heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safely. If the provided plug does not fit into your
outlet. Consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
FCC Rule : TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT : FOR HOME OR OFFICE USE.
FCC COMPLIANCE STATEMENT :
This device complies with part 15 of the FCC rules. Operation is subject to
11) Only use attachments/accessories specified by the manufacturer.
12) Do not place the apparatus on an unstable cart, stand or table. The apparatus may
fall, causing serious damage to the apparatus.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
moisture, does not operate normally, or has been dropped.
the following conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference
that may cause undesired operation.
15) The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
INFORMATION TO USER:
This equipment has tested and found to comply with the limits of a Class B
digital device, pursuant to part 15 of the FCC Rules. These limit are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, user and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation, if this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1. Reorient / Relocate the receiving antenna.
Shock Hazard Marking and Associated Graphical Symbols
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Explanation of Safety Related Symbols
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
WARNING : To Reduce The risk of fire or electric shock, do not
expose this the TV to rain or moisture.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference from that to
which the receiver is connected.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
4. Consult the dealer or an experience radio / TV technician for help.
This symbol is intended to alert the user to the presence of important operating and
maintenance(servicing) instructions in the literature accompanying the appliance.
CAUTION : Changes or modifications not expressly approved by
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
WARNING : To Reduce The risk of fire or electric shock, do not expose this the apparatus to rain or moisture.
The main socket-outlet for connecting mains plug shall be accessibly close to this apparatus
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
2. GENERAL FEATURES
- Fully MPEG-2 & DVB Compliant
- Input Frequency 950�2150MHz
- Supports EPG, PIG
This receiver has been manufactured to satisfy the
international safety standards.
Please read the following recommended safety precautions carefully.
- Supports SCPC & MCPC from C / Ku-band
- 1 LNB Input Tuner with Loop Through IF Signal
- Tuner Symbol Rate : 1�45MS/s
- Fast Booting & Auto Scan
MAIN SUPPLY : AC 95V~240V 50 / 60 Hz
LOCATION : Locate the receiver indoor.
- Quick Channel Changing
Locate receiver away from potential hazards such as houseplants, lighting, raining and direct sunlight.
- Max. 4000 Channels(TV & Radio) Programmable
- User Friendly 256 Colors OSD & Easy GUI
- A lot of OSD Language supported
- Radio Channel Background Display
- Favorite Channel List Programmable
- Master PIN Code Function & Parental Lock Function
- 100 Steps Volume Control
OVERLOADING : Do not overload wall outlets, extension cords or adapters as this
can result in fire or electrical shock.
LIQUIDS : Keep liquids away from the receiver.
CLEANING : Before cleaning, disconnect the receiver from the wall socket.
Use a cloth lightly dampened with water (no solvents) to clean the exterior.
VENTILATION : Do not block the receiver ventilation holes. Ensure that free airflow is
maintained around the receiver.
Never set the receiver on soft furnishings or carpets. Do not use or store the receiver
where it is exposed to direct sunlight, or near heater.
Never stack other electronic equipment on top of the receiver.
Place the receiver at least 30mm from the wall.
- Automatic Detection of Forward Error Correction
- Window based S/W Download Program Supported
by RS232 Serial Port
- Set to Set Download (Main Program, Channel Data)
- 4:3, 16:9 Letter Box
- Support Closed Caption
ATTACHMENTS : Do not use any attachment that is not recommended by the manufacturer,
as it may cause a hazard or damage the equipment.
- 7 Segment-4 Digit Display
- 5 Keys on the Front Panel (Power On/Off, Channel
Up/Down, Volume Up/Down)
CONNECTION TO THE SATELLITE DISH LNB : The LNB connector cable has a
voltage in its center core. It is therefore recommended that the receiver is disconnected from
the mains power before connecting or disconnecting this cable.
- Various LNB Polarity Control
�22KHz Switching Control
- 6 RCA Output for Video, Audio L/R, Component
- S/PDIF Output for Digital Audio
- S-VIDEO Output
FAILURE TO DO SO COULD DAMAGE THE LNB.
SERVICING : Do not attempt to service this product yourself. Any attempt to do so will
make the warranty invalid.Refer all servicing to a qualified service agent.
- RF-Modulator Output
LIGHTNING : If the receiver is installed in an area subject to intense lighting activity,
protection devices for the receiver mains connector and modem telephone line are essential.
The individual manufacturer’s instruction for safeguarding other equipment, such as TV set,
Hi-Fi, etc., connected to the receiver, must also be followed during lighting storms.
- Zoom function
- Multi Picture
- Blind Scan
- USALS
GROUNDING : The ground of the LNB cable must be directly connected to the system
ground for the satellite dish. The grounding system must comply with local regulations.
4
SAFETY PRECAUTIONS
GENERAL FEATURES
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. HOW TO CONNECT YOUR RECEIVER
4) CONNECTING EXTERNAL AUDIO HI-FI SYSTEM
Please DO NOT plug in the main power supply cord until you have
finished all the connections.
To connect any external Audio Hi-Fi system, the receiver has been provided with
S/PDIF connector at the back of the receiver.
5) CONNECTING YOUR ANALOG RECEIVER
1) LOCATION OF THE RECEIVER
To facilitate the user using analog receiver to view analog channels,
the receiver has been provided with a loop through terminal marked a“s IF OUT”.
Connect the coaxial cable from this terminal to the
IF input terminal of your analog receiver.
Now by keeping the receiver in standby,
Your receiver should be placed under proper ventilation.
Don’t put in completely enclosed cabinet that will restrict the flow of air, Resulting overheating.
The location should be safeguarded from direct sunlight, excess moisture,
rough handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your antenna system.
you will be able to tune and view analog channels from your analog receiver.
2) CONNECTING THE RECEIVER WITH DISH SYSTEM
After installing your dish system, connect the coaxial cable from LNB of your dish antenna to
“LNB IN”terminal marked at the rear of the receiver.
All cable connectors should be finger tightened ; do not use any kind of wrench
on the cable over connectors.
The cable should be 75Ϊ impedence coaxial twisted at the end with a“F”type connector.
TV
TV
Antenna
Satellite
Antenna
3) CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can follow three method ;
through RF cable, RCA cable, COMPONENT cable and S-Video cable.
Connect the RF cable to the terminal marked“TV OUT”at the rear panel of the
receiver and its other end to the TV RF input socket.
Analog
Hi-Fi
SVR
Stereo Audio
6
HOW TO CONNECT YOUR RECEIVER
7
HOW TO CONNECT YOUR RECEIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
4. HARDWARE DESCRIPTION
4. A. FRONT PANEL
4. B. REAR PANEL
1) LNB IN : This port is to connect the coaxial cable from LNB of your Dish. The IF input is provided through
this port and the input frequency range is 950�2150MHz. Also the voltage switching 13V and 18V is
passed through this port.
1) POWER : This key is used to turn the receiver on and off (stand by).
POWER
C H
2) IF OUT : To enable the connection of an analog receiver. The receiver is provided with this port. Connect
this port to LNB IN port of the other receiver via RF Cable.
2) CH : These keys are used to change the channels.
3) SERIAL PORT : This is used to connect your receiver with computer through a serial cable.
This port can be used for upgrading software.
3) VOL : These keys are used to increase and decrease the volume
4) S/PDIF DIGITAL OUTPUT : This port is for the connection to the extenal Hifi system which has a optical
S/PDIF input interface.
level manually.
VOL
5) VIDEO, AUDIO R/L, COMPONENT( Y ,Pb, Pr ): These RCA connectors are used to connect any external
4) INFRARED SENSOR : This is to receive the IR commands from the
RCU. Do not block the view of the sensor.
video and audio.
INFRARED SENSOR
7 SEGMENT DISPLAY
6) ANT IN : This is used to connect your local RF channels to your TV through Loop.
5) 7 SEGMENT DISPLAY : This SEGMENT display will show the current
channel number.While the receiver is in stand by mode, the display will show
the current time.
7) TV OUT : This is used to connect your TV through RF cable.
8) POWER INPUT : This is to plug in the AC main power cord.
The input AC volts range is 95V~240V, 50/60Hz supply.
6)SMART CARD INTERFACE SLOTS : To watch scrambled
channels you should insert a smart card into Smart Card Interface issued the
service provider whom you subscribes to. Therefore you can watch only a
specific range of channels with entitlements in smart card. The smart card
includes information to decipher parameters necessary for descrambling the
program. Please note that the gold chip on the smart card should face
download and inward when you insert when you insert it into Smart Card
Interface.
9) S-VIDEO : This is used to connect your TV through S-Video Cable.
10) CH 3,4 : The switch select RF 3,4 channel number.
SMART CARD
INTERFACE SLOTS
11) POWER SWITCH : This is swith to turn on and off the AC main power.
⑤
⑧
⑥
①
⑩
⑦
④
⑨
②③
8
HARDWARE DESCRIPTION
HARDWARE DESCRIPTION
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. C. REMOTE CONTROL UNIT
1) POWER : This is used to switch the receiver to ON/STANDBY mode.
2) MUTE : This key is used to toggle between normal and muted audio.
15) LAST : This key is used to return to the previous channel.
16) AUDIO : This key is used to select the soundtrack list for the current service
and also used to select audio mode.
AUDIO
0
~
9
3) 0-9 NUMERIC KEYS : These keys are used to enter numeric values and to
select the channel directly by entering its number.
PAUSE
SAT
17) PAUSE : This key is used to pause the screen.
18) SAT : This key is used to select the satellite.
4) CH▲∙CH▼: These keys are used to change channels and to browse the menu.
5) VOL▶∙VOL◀: These keys are used to vary the volume level and to change the
F1
F2
F3
F4
19) F1, F2, F3, F4 : Function Keys.
cursor options in the menu.
HELP
20) HELP: This key is for Help.
MENU
EXIT
OK
6) MENU : This key is used to open up the menu.
7) EXIT : This key is used to exit from any menus.
8) OK : This key is used to enter and confirm any data to the receiver in the menu systems.
The Channel list can be accessed directly by pressing this Key
in the normal view mode.
9) Page Up : This key is used to page up the menu.
10) Page Down : This key is used to page down the menu.
11) FAV : This key is used to switch between favorite lists.
12) GUIDE : This key is used to open up the Electronic Program Guide.
13) i : This key is used to view the channel information.
FAV
GUIDE
INFO
14)
: This key is used to toggle between the TV channel and the radio channel.
10
HARDWARE DESCRIPTION
HARDWARE DESCRIPTION
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. SYSTEM SET-UP
5.A. Automatic channel search for a satellite
5. B. Manual channel search for a transponder
You can automatically detect and save all TV and Radio channels
of a satellite as follows :
You can automatically search and save all TV and Radio channels of
a transponder as follows :
■Select Menu/Installation/ Channel Scan.
Main Menu/Installation/
■Connect the receiver to all peripheral devices.
System Connection
■Select the satellite which you want to search.
Channel Scan
�
�
Power On
■Turn on the power of the receiver and other
devices.
Antenna Configuration Setting
■Insert all information of your antenna.
�
�
Main Menu / Installation /
Antenna Setup
■Select Main Menu/Installation / Antenna Setup
using CH ▲∙▼& OK keys.
■Select the satellite which you want to search
using VOL ◀∙▶keys.
■Select the transponder from transponder list
which you want to search.
Manual Channel Search
If you cannot find it from transponder list, you
should insert all the
�
transponder information
■Insert all information of your antenna.
Antenna Configuration Setting
(i.e., Frequency, Symbol Rate, Polarity and FEC).
■Press OK key, and the receiver will automatically
search for all channels contained in the selected
�
transponder.
■Press OK key, and the receiver will automatically
Automatic Channel Search
search for all TV/Radio channels from a satellite.
12
SYSTEM SET-UP
SYSTEM SET-UP
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6. MENU OPERATION
▲
▲
). Press the“OK”key to confirm your selection.
▲
keys(
▲
The main menu is classified into five sub menus which will carry out the
various operation individually.
Also, you can use the“
”key to select either TV channel list or Radio channel list.
Once the channel is locked, every time you try to watch the program, you will be asked to enter PIN
code. Press the“menu”key or“exit”key to return to previous menu.
1. MAIN MENU
2. B. DELETE CHANNEL
After installing your dish system and receiver with appropriate connectors, plug in the AC main
power and turn on the receiver.
Select the“Delete Channel”icon using the“left/right”keys(◀∙▶). Select the channel that you
want to delete from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”
Press the MENU key of the RCU. You will see the“Main
Menu”on the TV screen as follow.
▲
▲
▲
keys(
). Press the“OK”key to confirm your selection. Also, you can use the“
”key to
▲
select either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
You can move into the desired submenu using the
“up/down”keys (▲∙▼) or numeric keys.
Press“OK”key to confirm your selection. If the“Main
Menu”is locked, note that you should enter the PIN
code in order to move into the corresponding submenu
in case o“f Edit Channels”menu“, Edit Favorites”menu
and“Installation”menu.
The default factory PIN code is“0000”.
Press the“menu”key or“exit”key to return to previous
menu.
2. C. MOVE CHANNEL
Select the“Move Channel”icon using the“left/right”keys(◀∙▶). Select the channel that you
want to move from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”
▲
▲
▲
keys(
). Press“OK”key to confirm your selection.
▲
Move it to the position where you want to place it using the“up/down”keys(▲∙▼) and the“page
▲
▲
▲
up/down”keys(
). Press the“OK”key to confirm. Also, you can use the“
”key to select
▲
either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
2. EDIT CHANNELS
2. D. EDIT CHANNEL NAME
Select the“Edit Channel Name”icon using the“left/right”keys(◀∙▶). Select the channel that you
You can edit channels on various channel lists - channel
lock, delete channel, move channel, edit the name of a
channel, and sort the channel list.
Selec“t Edit Channels”menu in main menu, and you will
be asked to enter your PIN code. You can find the
following“Edit Channels”screen by entering it.
want to edit from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”keys
▲
▲
▲
(
). Press“OK”key to confirm your selection.
▲
Select the character which you want to edit using the browse keys(▲∙▼,◀∙▶). Press“OK”key
to confirm.Save the character currently selected using the“F2”key. Also, you can use the“
key to select either TV channel list or Radio channel list. Press the“menu”key or“exit”key to
return to previous menu.
”
1. A. CHANNEL LOCK
2. E. SORT CHANNEL LIST
Select the“Channel Lock”icon using the left/right
keys (◀∙▶). Select the channel that you want to lock
or unlock from the channel list using the“up/down”keys
(▲∙▼) and the“page up/down”
Select the“Sort Channel List”icon using the“left/right”keys(◀∙▶). Press“OK”key to confirm.
Select the sort type which you want to sort using the“up/down”keys(▲∙▼). Press the“OK”key
to confirm.Also, you can use the“
”key to select either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
14
MENU OPERATION
MENU OPERATION
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. C. MOVE FAVORITE CHANNEL
3. EDIT FAVORITES
You can choose TV channel list or Radio channel list in an alternative way by pressing the“
key on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Move Channel”icon using the“left/right”keys(◀∙▶).
”
You can edit the favorite channel list, such as add/delete a channel or move its position, which
facilitates you to easily find your favorite channel from the favorite channel list.
The favorite channel is classified into one of 8 favorite categories depending on its genre.
Selec“t Edit Favorite”menu in main menu, and you will be asked to enter your PIN code.
You can find the following“Edit Favorite”screen by entering it.
Select a channel that you want to move using the“up/down”keys(▲∙▼). and the“page
▲
▲
▲
up/down”keys(
). Press“OK”key to confirm your selection.Move it to the position where you
▲
▲
).
3. A. ADD FAVORITE CHANNEL
▲
▲
want to place it using the“up/down”keys(▲∙▼). and the“page up/down” keys(
Press the“OK”key to confirm.
▲
You can choose TV channel list or Radio channel list in an alternative way by pressing the“
key on the RCU.
”
Press the“menu”key or“exit”key to return to previous menu.
By pressing“FAV”key on the RCU, you can choose
your favorite channel group out of 8 favorite groups.
Select the“Add Channel”icon using the“left/right”
keys(◀∙▶). Select a channel that you want to add
3. D. RENAME FAVORITE GROUP
You can choose TV channel list or Radio channel list in an alternative way by pressing the“
key on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
”
into the favorite channel list using the“up/down”
▲
▲
).
▲
keys(▲∙▼) and the“page up/down“keys (
▲
Press the“OK”key, and the selected channel will be
added to the favorite channel list. Press the“menu”key
or“exit”key to return to previous menu.
Select the“Rename Favorite Group”icon using the“left/right”keys(◀∙▶).
Press the“OK”key and select the character which you want to edit using the browse keys(◀∙▶,
▲∙▼).
Press the“OK”key to confirm.
Save the character currently renamed using the“F2”key.
Press the“menu”key or“exit”key to return to previous menu.
3. B. DELETE FAVORITE CHANNEL
You can choose TV channel list or Radio channal list in an alternative way by pressing the“
key on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
”
3. E. SORT CHANNEL LIST.
You can choose TV Channel list or Radio channel list in an alternative way by pressing the“
key on the RCU.
”
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Sort Favorite List”icon using the“left/right”keys(◀∙▶). Press“OK”key to confirm.
Select the sort type which you want to sort using the“up/down”keys(▲∙▼).
Press the“OK”key to confirm.
Select the“Delete Channel”icon using the“left/right”keys(◀∙▶).
Select a channel that you want to delete from the favorite channel list using the“up/down”
▲
▲
▲
keys(▲∙▼) and the“page up/down”keys(
). Press the“OK”key, and the selected channel
▲
will disappear from the favorite channel list.
Press the“menu”key or“exit”key to return to previous menu.
Press the“menu”key or“exit”key to return to previous menu.
16
MENU OPERATION
MENU OPERATION
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LNB Power
: Depending on the user’s antenna LNB, you can supply either LNB power by
setting“ON”or not by setting“OFF”. Normally set this to“ON”.
: You can select the LNB type.
: You can select the predefined LNB frequency or manually enter a specific
frequency in MHz unit by pressing numeric keys.
LNB Type
LNB Freq.
4. INSTALLATION
“Installation”menu helps you to setup a variety of
parameters necessary for receiving signal, add
new service, upgrade the new software and reset
the channel data.
22KHz
: In case you are using two antennas connected to a 22KHz tone switch box,
you can supply either 22KHz by setting“ON”or off by setting“OFF”to select
antenna.
: You can search all the free channels & scramble channels or only free channels
or onlyscramble channels by setting the search option.
: If you have DiSEqC box, you can choose port by selecting port number.
Otherwise, choose“none”.
: If you have a DiSEqC 1.2 motorised system, then you can takeadvantage of the
DiSEqC 1.2 functions available. Choose Installer as Motor and press “F1” key.
After that, adjust antenna direction using browse keys.
Search option
DiSEqC 1.0
Motor
Selec“t Installation”menu in main menu, and you
will be asked to enter your PIN code.
You can find the following“Installation”screen by
entering it.
4. A. 1 Automatic Scan
4.A. ANTENNA SETUP
Check the signal strength. Press“OK”key to start the scan procedure.You can see the
progressive status of channel searching.
Please note that the scan procedure may take a few minutes.
Press the“menu”key or“exit”key to return to previous menu.
Your receiver includes the preprogrammed information of transponders contained in various
satellites.
You can update the transponder list preprogrammed
for a satellite by adding a new transponder to it or
modifying the information of the existing transponder.
(Refer to the Channel Scan described in section 4.B)
Selec“t Antenna Setup”menu in“Installation”menu
and the following screen will be displayed.
4. A. 2 Blind Scan
Blind Scan search the channel when you don’t know
the transponder information.
Press the F2 key to start the blind scan procedure
and the following screen will be displayed.
Please note that the scan procedure may take a few
minutes.
Select the desired satellite using the“left/right”
keys(◀∙▶).Se“t LNB Power”“, LNB Type”“, LNB
Freq”“, 22KHz”“, Search Option”, and“DiSEqC 1.0”
fields to the appropriate value using the left/right
keys(◀∙▶) at each field.
Press the “menu” key or “exit” key to return to
previous menu.
18
MENU OPERATION
MENU OPERATION
19
Download from Www.Somanuals.com. All Manuals Search And Download.
You can see the progressive status of channel searching.
4. A. 3 USALS
If you cannot find the desired transponder from the transponder list, you can add it by inputting
appropriate parameter values for a new transponder using the“F1”key. When you want to
change the parameter of an existent transponder, select the parameter using the“F1”key,
change its value and press the“Exit”Key.Correctly set various parameters.
-Please go to Antenna Setup and select USALS
from motor.
-Press F1 then Pop-up will be appeared.
-Press arrow button to write Longitude
-Press arrow button to write Latitude, then OK to
work.
: Input the frequency of the transponder you want to find manually.
: Inputs the symbol rate of the transponder you want to find.
Freq.
S/R
: Select the polarization of the transponder you want to find. In the case of
horizontal,18V and in the case vertical, 13V are output through LNB line.
PoI.
:
Select the FEC of the transponder you want to find. You can select the value of 1/2,
2/3, 3/4, 5/6, 7/8 or auto.
FEC
4. B. CHANNEL SCAN
It will be more convenient to use“Channel Scan”procedure when you want to search
channel for a specified transponder offered from the satellite. As in“Antenna Setup”,
“Channel Scan”also searches all channels broadcasted over a specific transponder
using its predefined information. You can add a new transponder if you cannot find it on
the predefined transponder list.
4. B. 2 ADD SATELLITE
You can add a new satellite. Select the“Add Satellite”icon using the“left/right”keys (◀∙▶),
and press the“OK”key.
Select“Channel Scan”menu in“Installation”menu, and the following screen will be
displayed.
Select the“Search/Edit TP”icon using the“left/right”key (◀∙▶). Press the“OK”key and add
a new transponder using the“F1”key. You should set various parameters of the transponder.
The default name of the added satellites is“UserSAT-No.”
4. B. 1 Channel Scan
4. B. 3 RENAME SATELLITE
Select the desired satellite using the“left/right”keys (◀∙▶).
Select the“Antenna Configuration”icon using the browse keys(▲∙▼,◀∙▶).
Press“OK”key, and set“LNB Power”,“LNB
Type”“, LNB Freq”,“22KHz”,“Search Option”, and
“DiSEqC 1.0”fields to the appropriate value using
the“left/right”keys(◀∙▶) at each field. Check the
signal strength and press“Exit”key.
You can also change the satellite name. Select the“Rename Satellite”icon using the“left/right”
keys (◀∙▶).
Press“OK”key and select the character which you want to edit using the browse
keys (▲∙▼,◀∙▶). Press the“OK”key to confirm. Save the character currently renamed using
the“F2”key.
4. B. 4 DELETE SATELLITE
Select the“Search/Edit TP”icon using the“left/right”
keys(◀∙▶). Press“OK”key, and select the
desiredtransponder using the“up/down”keys (▲∙
▼). Press“OK”key to start the manual searching for
selected transponder.
You can also delete the user satellite. Select the satellite that you want to delete from the satellite list.
Select the“Delete Satellite”icon using the browse keys (▲∙▼,◀∙▶).
Press the“OK”key, and the selected satellite will disappear.
20
MENU OPERATION
MENU OPERATION
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. C. PARENT CONTROL
This function prevents children or unauthorized
persons from watching programs.
Also you can change PIN(Personal Identification
Number) code.
Select“Parental Control”menu in“Installation”
menu, and the following screen will be displayed.
Time Mode
: Select the time mode of your receiver. In Auto mode, your receiver will
use the information from the satellite as time reference. In manual
mode, you can set the time of your receiver manually.
: Set the time offset from the UTC (GMT).
Time Adjustment
Useful in auto mode only.
Current time
Summer Time
: Set the current time manually. Useful in manual mode only.
: Enable or disable the Summer Time. Most European countries use the
Summer Time.
4.C.1 Receiver Lock
To lock receiver, select“Receiver Lock”in the“Parental Control”menu and change it to“On”
mode using the“left/right”keys (◀∙▶).
Useful in auto mode only.
On time
Off time
: Set the time when the receiver will be automatically turned on
: Set the time when the receiver will be automatically turned off.
4.C.2 Menu Lock
To lock the Main Menu, select“Menu Lock”in the“Parental Control”menu and change it to
“On”mode using the“left/right”keys (◀∙▶).
4.C.3 Change PIN Code
4. E. RECEIVER UPGRADE
You can change your PIN code from factory default value“0000”as follow:
Select“Change PIN Code”in the“Parental Control”menu using the“left/right”
keys(◀∙▶).
Press“OK”key. Then you will be asked for a new PIN code.
Once you enter a new PIN code, the receiver will ask you to enter it in again.
After you enter a new PIN code twice, the PIN code is changed permanently.
If you forget the PIN code, you have to contact the distributor to find out it.
You can upgrade the software of this receiver through
serial port when the new software is released.
Please contact the distributor for receiver upgrade.
Distributor supports you useful information and new
software for the receiver.
4. D. TIME SETTING
You can change the time of your receiver and also
switch on/off the timer function in this menu.
4. F. FACTORY DEFAULT
Select “Time Settings” item in the “ Receiver Settings”
menu and the following screen will be displayed.
This is to restore the factory set values in case the user has encountered some problems after
changing any new values of channel data and others which may be in error.
Selec“t Factory Default”menu in“Installation”menu and press“OK”key.
If you want to continue, select option“Yes”.The receiver will be reset to settings automatically.
Please note that the“Factory Default”procedure may take a few minutes.
22
MENU OPERATION
MENU OPERATION
23
Download from Www.Somanuals.com. All Manuals Search And Download.
7. CHANNEL LIST
This menu helps you to easily select the channel that you want to watch.
5. SYSTEM SETTINGS
The channel list is separately constructed for each
satellite. Press“OK”key, and the following screen will be
displayed. You can get the information of channel
number, channel name, and whether the program is
scrambled or locked.
This menu helps you to Set up video output
mode,
Ianguage, screen type and Selec“t System
Settings”menu in main menu
To watch a specific channel, first select it by pressing the
“up/down”keys (▲,▼) and the“page up/down”keys
▲
▲
▲
(
,
). Then, press“OK”key. This enables you to move
▲
into that specific channel.
You can also select a specific satellite using the“SAT”
key. When you press the“
alternatively select TV or radio channel list. When you press Press the“menu”key or“exit”key to
”key, you can
Screen Type
: You can choose either 4:3 or 16:9 according to the TV type.
Menu Transparency : You can select the transparency of the menu.
return to previous menu.
Menu Language
Audio Language
Channel Mode
: You can select the menu language.
: You can select the audio language.
: You can select the channel mode when channel is changed.
: If this is “on” , receiver will beep out the signal status.
Beep for scanning
8. CHANNEL GUIDE
Press“GUIDE”key, and the following screen will be displayed.It will give the titles of the current
and next programmes on different channels.
Press the“menu”key or“exit”key to return to previous menu.
The information may include : current time / channel
name, name of the current and next programme, the
start and total time of the current programme, the start
and total time of the next programme.
6. GAMES
Programme information will be available only when it is
included in the transmission.
This menu helps you play game called Tetris. In this
game you can choose level from 1 or 9. Once you
choose game menu from main menu, you can choose
OK to start a game.
When you press the“
”key, you can alternatively
select TV or radio channel guide.
Press the“menu”key or“exit”key to return to previous
menu.
24
MENU OPERATION
MENU OPERATION
25
Download from Www.Somanuals.com. All Manuals Search And Download.
11. MULTI PICTURE
When you press”GUIDE” key again, Daily Guide will be
displayed. You can see all events for selected chanel.
You can use the Multi-picture Function using F1 key.
You can watch four, six or nine pictures at the same
time using this function. And select the number of
pictures using (▲,▼) keys and press OK. After that,
you can see the Multi-Picture Screen. Also you can
select the channel using(◀,▶ ▲,▼) keys and OK
key in the Multi-picture Screen. The channel of your
selection is only live signal when you selected one
channel of the several channels. The channels of
which is not selected are just the pictures.
9. AUDIO
Press“AUDIO”key.
Select the audio mode which you want using the“left / right”keys(◀,▶).
Some programs are broadcasted with one or more alternative language soundtracks.
You can select the preferred audio language for soundtrack using the“up/down”keys (▲,▼).
6 Picture
9 Picture
4 Picture
10. ZOOM FUNCTION
12. COLOR SETTING MENU
You can adjust the color seting to take the enhonced
TV screen. Press “F2” key then below screen will
display.
On the live TV screen or paused TV screen, you can magnify some region of TV screen.
Press “F4” key and the ZOOM box will be display.
You can use following keys.
- Up/Down/Left/Right keys (▲∙▼,◀∙▶) : Move the ZOOM box
▲
▲
▲
- Page Up/Page Down keys (
,
) : Increase or decrease the ZOOM box
▲
OK
- OK key (
- Exit key (
) : Watch the ZOOM box to full screen or return to ZOOM box
) : Return to the live screen
EXIT
26
MENU OPERATION
MENU OPERATION
27
Download from Www.Somanuals.com. All Manuals Search And Download.
7. TROUBLE SHOOTING
Mode
: You can select this to “Default” or “User”
When “Mode” is “User” , you can change each color value.
Problem
Solution
About the Receiver
Does not display LED on the
front panel or the receiver has no power.
- Connect the power cord to the power outlet
properly.
Brightness
Contrast
Saturation
Sharpness
: If your receiver connected to TV by using “VIDEO” or “S-VIDEO”
Connector , these items will change the color setting of TV
screen.
- Check if the receiver is in standby mode.
- Check if the video output port is firmly
connected to the Tv.
No pictures on the screen
M_B_Y
M_G_U
M_R_V
: If your receiver connected to TV by using “Component cable
“(Y-Pb-Pr)” , these three items will change the color setting of TV
screen.
- Check if you have selected the correct
channel or video output on your TV.
- Connect the audio cords properly.
- Check the volume level of the TV.
- Press“MUTE”key.
No sound
- Point remote control directly towards the
receiver.
Remote Control does not operate
- Check and replace batteries.
- Check the signal strength in the“Antenna
Setup”menu.
- If this is low, try adjusting the alignment of
Poor picture quality
Searching Signal
your dish.
On - Screen Error Messages
- Connect the antenna cable properly.
- Check the LNB. Please replace LNB if
necessary.
- Check the position of the dish. Please realign
dish if necessary.
- Check the signal strength in the“Antenna
Setup”menu.
Unrecognized smartcard
- Check the smartcard.
- Insert the smartcard.
Please insert your smartcard
28
MENU OPERATION
TECHNICAL SPECIFICATIONS
29
Download from Www.Somanuals.com. All Manuals Search And Download.
8. TECHNICAL SPECIFICATIONS
5. Audio Decoder
System Decoding
1. Power Supply
: MPEG-1 ISO/IEC 11172-3
Layer I & II
: Mono, Dual, Stereo, Joint Stero
: 32, 44.1, 48 KHz
: SMPS
: AC 95V~240v 50Hz / 60Hz
: 250V/T2A
Type
Input Voltage
Fuse Rating
Audio Mode
Sampling Frequency
2. Tuner
6. Audio/Video Output
: 950�2150MHz
: -65�-25dBm
: 75ΪUnbalanced
:‘F’Type Female
: 13V/18V, Max 500mA with Short Circuit Protection
: Frequency 22±4KHz, Amplitude 0.6±0.2Vpp
: 1.0 & 1.2 Version Compatible
: PLL Frequency Synthesizer
Input Frequency
Input Signal Level
Input Impedance
Connector Type
LNB Power Supply
22KHz Tone
: 2 RCA Cinch
: 1 RCA Cinch
: 1 S/PDIF(Optical)
: 1 S-VIDEO
Audio Output
Video Output
Digital Audio
S-Video
: 3 RCA Cinch
COMPONENT
DiSEqC
Channel Selection
7. RF Modulator
: CH3~4
: NTSC
Modulator Output
Video Type
: “F” Type Female
: “F” Type Female
Output Connector
Ant. IN Connector
3. Demodulator
Type
Symbol Rate
Inner FEC
: QPSK Demodulation(DVB-S)
: 1�45 MS/s
: Viterbi Convolutional Coding
Rate 1/2, 2/3, 3/4, 5/6, 7/8
: Reed Solomon Coding(204,188) T=8
8. Serial Data Interface
: RS-232, Max. 115200 bps
: 9 Pin D-Sub(male)
Signal
Connector Type
Outer FEC
9. Embedded Descramble
4. Video Decoder
X Crypt Conditional Access System
System Decoding
Profile and Level
Data Rate
: MPEG-2 ISO/IEC 13818-2
: MPEG-2 MP@ML
: 1�15 MB/s
Video Formats
: 4:3(Normal) & 16:9(Widescreen)
30
TECHNICAL SPECIFICATIONS
31
TECHNICAL SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
|