SATELLITE DISH ANTENNA
SELF-INSTALLER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Universal Accessories
D940EXP 2nd Room Kit
With one digital satellite system, use the D940EXP 2nd Room Kit to view the same
programming in another room. And, control your receiver with the Universal Remote
included in the kit. Easy to install, your kit includes all the necessary hardware:
Signal Sender System - Converts infrared (line of sight) signal
into radio frequency (goes through walls).
Digital Satellite System Universal Remote - Keep your original
remote with your Digital Satellite Receiver and use this remote
in the 2nd Room. Preprogrammed to work your receiver and 4
additional components.
100 ft. Coaxial Cable - Used to run from your Digital Satellite
Receiver to your 2nd Room TV.
3 ft. Coaxial Cable and Two-Way Splitter - Used to connect your
primary and secondary TVs to your receiver.
$9995
$4995
ANT200 Amplified TV Antenna
Connect your Digital Satellite System Receiver to the ANT200 Amplified Antenna
and begin receiving your local network stations. The built in A/B switch makes it
easy to switch between satellite stations and your local programs. With its unique
design, you can boost your UHF/VHF TV signals for improved broadcast reception.
D916 Wireless Phone Jack System
This handy device lets you turn any electrical outlet into a phone jack instantly. Use
it to make the telephone connection to your Digital Satellite System Receiver. Easy
to install in just minutes!
$7995
$2495
D903 In-Line Amplifier
Amplifies incoming signal for best picture when installation requires long coaxial
cable runs. (For Indoor Use Only)
D915 CHIMNEY MOUNT
Made of durable steel, the D915 Chimney Mount allows you to mount your Digital
Satellite System to any size chimney.
$2295
$5995
D940 REMOTE CONTROL SIGNAL SENDER
Control your Digital Satellite Receiver from any room. Just plug it in! The Remote
Control Signal Sender transmits your remote control signal from one room to another
- through walls and floors. Extends the range of your remote control up to 140 feet.
Also works most VCRs and Laserdisc Players from anywhere in your home. Contains
one base unit and one extension unit. Each unit is only four inches tall. Additional
extension units are available (Model #D935).
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Order Form
To order accessories, contact your local Dealer. If a dealer is not nearby, you can also follow the
directions below to order by telephone or by direct mail.
To place your order by phone, have your VISA, MasterCard or Discover Card ready and call the toll-
free number listed below between 8:00 am and 10:00 pm (EST), Monday thru Friday, or 9:00 am
and 5:00 pm (EST), Saturday. USE THIS number only to place an order for the accessories listed on
this order form.
1-800-338-0376
To place an order by mail, detach and mail the completed order form with credit card information,
check or money order (in U.S currency), made payable to Thomson Consumer Electronics, Inc., to
the following address.
Video Accessories
P.O. Box 8419
Ronks, PA 17573
DESCRIPTION
PART NO.
D940EXP
D915
PRICE
99.95
22.95
49.95
79.95
24.95
59.95
QTY.
TOTAL
2nd Room Kit
Chimney Mount
Amplified Antenna
Wireless Phone Jack System
In-Line Amplifier
ANT200
D916
D903
Remote Control Signal Sender
D940
Remote Control Signal Sender
Extension Unit
D935
39.95
TOTAL MERCHANDISE
SALES TAX
We are required by law to collect the appropriate sales tax for each individual
state, country, and locality to which the merchandise is being sent.
SHIPPING AND HANDLING
TOTAL AMOUNT ENCLOSED
5.00
PRICES SUBJECT TO CHANGE WITHOUT NOTICE
Please Allow 4 - 6 Weeks For Delivery
Use VISA, MasterCard or Discover Card. Money Order or check must be in U.S currency only. No
COD or cash.
Name: ___________________________________________________________________________________
Address:_________________________________________________________________________________
City:___________________________________
Zip Code:_____________________________________
❑ Visa ❑ MasterCard ❑ Discover
Credit Card Number: _______________________________ Expiration Date:____________________
Signature: (Required for Credit Card Orders)_______________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Table Of Contents
Preparing for Installation................................................ 3
Installation Overview................................................................... 4
The Big Question: Should I Do This Myself? ................................ 5
General Site Survey ...................................................................... 5
Finding a Clear Line of Sight ................................................................... 6
Where Is The Satellite, Anyway? .............................................................. 6
How High Up in the Sky is the Satellite? .................................................. 6
Finding the Dish Pointing Coordinates ........................................ 7
Connecting the Receiver to a TV ............................................................. 7
Using the Dish Pointing Menu Screen ...................................................... 8
Precise Site Survey ....................................................................... 9
A Final Site Survey ................................................................................ 10
Estimating Cable Requirements ................................................. 11
Cable Estimate Procedure...................................................................... 12
Dish Assembly Overview ........................................................... 13
Partial Dish Assembly................................................................ 14
Setting the Elevation on the Dish............................................... 14
Mounting the Mast ........................................................ 15
Mounting The Mast On Solid Wood Or Lap Siding...................... 16
Important Considerations: .................................................................... 16
Mounting Instructions........................................................................... 17
Installing a Spacer................................................................................. 18
Mounting the Mast on Brick or Poured Concrete ....................... 19
IMPORTANT Considerations .................................................................. 19
Mounting Instructions........................................................................... 19
Mounting the Mast on a Hollow or Cinder Block Wall ................ 20
IMPORTANT Considerations .................................................................. 20
Mounting Instructions........................................................................... 21
Mounting Instructions........................................................................... 23
Mounting the Dish On A Pole ..................................................... 23
Mounting the Mast on a Roof ..................................................... 25
Step-by-step Instructions for Mounting the Mast on a Roof ................... 25
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Final Installation ........................................................... 27
Leveling the Mast....................................................................... 28
Leveling Side-to-Side ............................................................................. 28
Leveling Front-to-Back .......................................................................... 29
Final Dish Assembly .................................................................. 29
Routing and Grounding the Cables ............................................ 31
A Few Words About Grounding
the System ................................................................................. 31
Running Cable Into the House ................................................... 33
Making the Final Connections .................................................... 34
Acquiring and Fine Tuning the Signal ........................................ 35
Adjusting the Azimuth and Elevation Settings ....................................... 36
Ordering Programming .............................................................. 37
Troubleshooting......................................................................... 38
Can’t Pick Up the Satellite Signal ........................................................... 38
Temporary Satellite Signal Loss ............................................................. 39
You Hear Sound While Talking on the Phone.......................................... 39
Digital Satellite System Installer's Reference ............................ 40
Support Line ......................................................................................... 40
Program Providers ................................................................................ 40
Digital Satellite System Publications ...................................................... 40
Index .......................................................................................... 41
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for Installation
There are a few tasks you need to complete before you
will be ready to mount the satellite dish, the most
important of which is to make sure you have a clear
line of sight to the satellite.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Overview
Installation Overview
The manual is organized into steps that need to be performed in the order
presented.
Preparing for Installation
• Complete a General Site Survey – Visually survey your location to make sure
it is suitable.
• Obtain Dish Pointing Coordinates – Use the on-screen menu system to
obtain the exact coordinates (azimuth and elevation) for pointing the dish.
Directions for using on-screen menus can be found in your receiver manual.
• Select the Precise Mounting Site – Use the dish pointing coordinates to
conduct a precise site survey to determine the exact mounting site.
• Estimate Cable Requirements – Based on your mounting site, you will decide
where you want the cable to enter your house, and measure how many feet of
cables you need to complete the connection.
• Begin Dish Assembly – Attach the reflector to the support arm so that you
can preset the correct elevation.
• Set the Elevation on Dish – This is an important step. Making sure that your
elevation setting is correct will help you to more easily obtain the signal later
on.
Mounting the Mast
• Mount the Mast – Step-by-Step mounting instructions for each mounting
option.
Completing the Final Installation
• Level the Mast – The mast must be level to obtain the signal.
• Complete the Dish Assembly – Place the dish on the mast and connect the
RG-6 coaxial cable to the LNB, and attach the LNB to the support arm.
• Route the Cables to the Grounding Block – Attach a grounding block to the
house and route the cables from the dish to the grounding block. Also, route
grounding wire from the grounding block to the central building ground.
• Run the Cables from Grounding Block into the House – Run the RG-6 cable
from the grounding block into the house and to the back of the receiver.
• Make the Final Connections to the Receiver – Connect the RG-6 to the
satellite input on the receiver, and make the phone line connection.
• Acquire and Fine-Tune the Satellite Signal – Use the on-screen signal meter
to check for a signal. Once the signal is obtained, adjust dish pointing to
achieve maximum signal strength for your location.
• Order Satellite Programming – Call the service providers to order satellite
programming.
4 Preparing for Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
General Site Survey
The Big Question: Should I Do This Myself?
While the installation is not difficult, it does require that you have some
experience in electrical wiring and minor construction techniques. Also,
you may have to climb a ladder, so you’ll want to be comfortable working
with heights.
Question: Have you installed any of these home products or completed
tasks similar to them?
•
•
•
•
•
TV antenna outside your house
ceiling fan
basketball goal
dimmer switch
garage door opener
If the answer is YES, then you can be reasonably confident that you can
install the Digital Satellite System yourself.
If the answer is NO, then this is probably not the time to learn. Consider
contacting your local authorized DSS® retailer to recommend a
professional installer.
General Site Survey
To get a signal, the satellite dish must be pointed directly at the satellite,
with NO obstructions between the two. This means NO trees and NO
buildings. Take into consideration future tree growth, house remodeling
or additions and new construction in your area.
The satellite signal WILL NOT PASS through leaves or branches.
The satellite signal WILL NOT PASS through glass; don’t try to install your
dish indoors!
Preparing for Installation 5
Download from Www.Somanuals.com. All Manuals Search And Download.
General Site Survey
Where Is The Satellite, Anyway?
The satellite is always located south of Texas. That means if you live
in Miami, you must have a clear line of sight to the southwest; if you
live in San Francisco, you must have a clear line to the southeast.
How High Up in the Sky is the Satellite?
Depending on where you live, the satellite will be at an elevation
angle between 30 and 60 degrees. Southern states point more toward
60 degrees; northern states point more toward 30 degrees.
Indianapolis, IN
look southwest
90°
N
S
N
S
60°
W
E
W
E
San Francisco, CA
look southeast
30°
N
S
0°
W
E
Miami, FL
look southwest
Satellite is here
Finding a Clear Line of Sight
1. Go outside and locate at least one site on your property that
has a clear view to the satellite. You should be reasonably
certain you are pointing toward Texas (unless you’re in
Texas, in which case you should be looking due south). You
may want to use a map.
60°
30°
NO
2. Imagine an arc ranging from 30 to 60 degrees above
the horizon.
60°
30°
3. Do you have at least one clear view to the satellite?
Remember, no trees, leaves, buildings, or windows can be
between the dish and the satellite.
MAYBE
If the answer is NO, your site may be unsuitable for
installing the satellite system.
If the answer is MAYBE, you may want to contact a your
local digital satellite dealer for information about having a
professional installer conduct a thorough site survey.
60°
30°
YES!
If the answer is YES, your site should be suitable for
installing the system. Go ahead to the next section in this
manual.
6 Preparing for Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding the Dish Pointing Coordinates
Finding the Dish Pointing Coordinates
Additional
Information
You need to connect the satellite receiver to your TV and use the
on-screen menu system to find the dish pointing coordinates for
your location.
This example shows a basic
connection. Refer to the
manual that accompanies
the receiver for additional
connection options.
Connecting the Receiver to a TV
For this task, you use the most basic connection to save time.
After you have installed your system, you may want to consult
the instruction manual that accompanies the receiver for more
advanced connection options.
1. Connect a coaxial cable to the OUT TO TV jack on the
satellite receiver, and to the antenna IN jack on your TV.
NOTE
TV
Make sure that you are
connecting to the OUT TO TV
jack on the receiver. Some
models may have the outputs
in different positions than
shown in the diagram to
the left.
IN
SATELLITE
IN FROM ANT
RECEIVER
OUT TO TV
CH 4
CH 3
CH3/CH4 switch
2. Make sure that the TV and the satellite receiver are both
plugged into an AC power outlet.
3. Turn on the TV and the satellite receiver.
4. If the satellite receiver has a CH3/CH4 switch on the back,
tune your TV to channel 3 or 4. If the satellite receiver does
not have a CH3/CH4 switch, tune to UHF channel 14, or cable
channel 65.
CAUTION
Do not stack electronic
components on top of
the digital satellite
receiver.
Preparing for Installation 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding the Dish Pointing Coordinates
Using the Dish Pointing Menu Screen
The satellite receiver has an on-screen menu feature for obtaining the
precise dish pointing coordinates for your location. You can use the
buttons on the front panel of the receiver to navigate through the
menu system, or you can use the remote control. If you have not
already inserted batteries into the remote, you can do that now.
Directions for using on-screen menus can be found in your receiver
manual.
When you’ve obtained the coordinates, record the elevation and
azimuth numbers below.
Elevation ______________
Azimuth ________________
Elevation is the up/down angle
that the dish is pointed
Azimuth is side to side direction
that the dish is pointed
8 Preparing for Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Precise Site Survey
Precise Site Survey
Based on your general site survey, you probably already know
where you want to mount your dish, but it’s a good idea to follow
the procedures outlined in this section in order to make sure that
your site selection is a good one.
Tip
You may want to review the
section “Mounting the Mast”
and consider the mounting
options before completing
your precise site survey.
1. Go outside to your install site and hold a compass flat in the
palm of your hand. Hold your hand still until the needle stops
moving (the dark or colored half of the compass needle always
points north).
2. Rotate the compass so that the “N” (for north) is directly under
the dark part of the compass needle. Your compass is now
aligned with north. The tick marks around the edge of the
compass represent azimuth degrees.
3. Locate the tick mark on the compass that corresponds to the
azimuth number you wrote down. This is the direction of your
azimuth setting (the direction the dish will need to be pointed
to receive signals from the satellite).
Tip
Rotate until N lines up with
the dark half of the arrow
Try to keep the compass
away from any metal
objects. Metal objects can
cause inaccurate compass
readings.
If you live in
San Francisco,
the satellite will be
to the southeast
If you live in Miami,
the satellite will be
to the southwest
4. Raise your arm to approximately the elevation angle recorded
earlier to make sure that there are no obstructions in the signal
path.
90°
60°
30°
WARNING
Do NOT install the dish
near power lines,
0°
electric lights or power
circuits. Contact with
power lines, lights or
power circuits may be
fatal. It is recommended
that the dish be located
more than 20 feet from
overhead power lines.
5. Repeat this survey in several places on your property if
necessary until you find the best mounting location.
Preparing for Installation 9
Download from Www.Somanuals.com. All Manuals Search And Download.
A Final Site Survey
Now that you’ve conducted a precise site survey using the dish pointing
coordinates for your location, you should double-check one more time
to make sure you have a clear view to the satellite.
60°
30°
NO
I Don’t have a clear view to the satellite.
If you don’t have a clear view to the satellite, then your site may not be
suitable for installing the satellite system. A professional installer may
have an alternative solution—consider contacting your satellite system
dealer to find the name of an authorized satellite system installer.
60°
30°
MAYBE
I’m Not sure If I have a Clear View
If you’re not certain whether you have a clear view to the satellite, you
have two choices :
•
Continue with the installation and determine whether you have a
clear view to the satellite by testing the system.
•
Contact your satellite system dealer to find the name of an
authorized satellite system installer who can help you verify that
your property is suitable for installation.
I Have A Clear View to the Satellite
Your site should be suitable for installing the satellite system.
Continue with the installation.
10 Preparing for Installation
Estimating Cable Requirements
Estimating Cable Requirements
Now that you’ve decided on the exact mounting site, you need to
decide where you want the cable to enter the house, and then figure
out approximately how much cable you are going to need.
The diagram below shows you a “typical” installation scheme,
outlining the cables that are needed. The information on the following
page takes you through the cable estimating process step-by-step.
Grounding block
Messenger (ground) wire
grounded to block
Cable entry into house
RG-6 coaxial cable #2
(no messenger wire)
RG-6 coaxial cable #1
with messenger wire
Messenger (ground) wire
attached to the mounting foot
DSS receiver
#10 Copper or #8 Aluminum
Grounding wire goes to
Central Building Ground
A Few Words About
Grounding the
System
Grounding the satellite
system to the central
building ground helps
protect it and other
TV
components from lightning
damage. Dish installation
should comply with local
codes and the National
Electrical Code (NEC).
Grounding the satellite
system is something you can
probably do yourself. But if
you’re not sure, you should
contact a qualified
electrician.
Preparing for Installation 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Estimating Cable Requirements
Tip
Cable Estimate Procedure
If you have a dual-output
LNB and plan to connect
your dish to two separate
receivers, don’t forget to
double the RG-6 cable
estimate to the grounding
block, and include a
1. Locate the central building ground. You will ground the dish (via
the cable grounding block) to a single point in the central building
ground. The following is a list of acceptable building ground points:
•
Grounded interior metal cold water pipe within five feet of the
point where it enters the building.
separate estimate from the
grounding block to the
second receiver.
•
•
•
Grounded metallic service raceway.
Grounded electrical service equipment enclosure.
Eight-foot grounding rod driven into the ground (only if
bonded to the central building ground by #6 or heavier
bonding wire).
•
Other acceptable grounding electrodes that comply with
sections 250 and 810 of the National Electrical Code (NEC).
2. Choose a location to mount the grounding block. The block
should be as close as possible to the point where the cable will
enter the house.
3. Decide where inside the house you plan to put the satellite receiver.
4. Estimate the amount of cable you will need for each of the
following:
•
One (1) RG-6 coaxial cable with messenger (ground) wire to
run from the dish to a grounding block for each LNB output.
The grounding block should be located near the cable’s point
of entry into the house.
Note
You must use RG-6 coaxial
cable from the satellite dish
to the SATELLITE IN jack on
the receiver. Other types of
coaxial cable, such as those
used for cable television
(RG-59) do not work for the
digital satellite system.
Write that distance here:
.
•
•
One (1) RG-6 coaxial cable (per LNB output) to run from the
grounding block to each satellite receiver.
Write that distance here:
.
Note
Grounding wire (#10 copper or #8 aluminum) to run from the
grounding block to the central building ground.
If your total RG-6 coaxial
cable length from the dish
to the receiver is more than
112 feet, you may need
additional installation
Write that distance here:
.
component, such as a line
amplifier, to compensate for
the longer cable length.
12 Preparing for Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Dish Assembly Overview
Dish Assembly Overview
Use this page both as a parts lists for your satellite antenna, and a general overview of how the
parts fit together; but DON’T ASSEMBLE THE DISH YET.
If your reflector looks like the
one on the left, you should
have:
Metal
Reflector
Note
If you have a plastic reflector,
Flat head bolts
the bolts are molded into the
reflector; on metal reflectors,
the bolts must be inserted
through the holes on the
reflector before attaching
the reflector to the support
arm.
•
Mounting foot and mast
Satellite dish reflector
LNB
•
•
Self-locking nuts
LNB (Low Noise Block
converter)
Retainer nut
Phillips head screw
•
•
LNB support arm
Hardware packet
LNB support arm
Mast
Nut, star washer,
hex head bolt
Mounting foot
If you have a Sony reflector, you
should have:
•
•
•
Mounting foot and mast
Reflector
Satellite dish reflector
LNB (Low Noise Block converter)
and LNB support arm
Pre-assembled
mast clamp
LNB
•
Hardware packet
LNB support arm
Mast
Mounting foot
Preparing for Installation 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Partial Dish Assembly
Partial Dish Assembly
1. Locate the reflector, the support arm, and the hardware packet.
2. Attach the reflector to the support arm :
• Metal Reflector: Pass the bolts through the reflector, and
then place the reflector on the support arm by inserting the
bolts through the holes on the support arm. Use a wrench to
secure the four self-locking nuts.
• Plastic Reflector: Pass the four bolts molded into the back of
the reflector through the four holes on the support arm. Place
a star washer and nut on each of the bolts and secure each
with a wrench.
• Sony Reflector: Align the screw holes on the LNB arm holes
and reflector bracket holes. Screw in the machine
screws,tightening the LNB support arm to the reflector
bracket. Do not over-tighten.
Hardware
Sony reflector
Metal
reflector
Plastic
reflector
Hardware
Hardware
Hardware
Support arm
Support
arm
Support
arm
Setting the Elevation on the Dish
After you have securely attached the reflector to the support arm, you
need to set the dish to point up toward the satellite. This is called
“setting the elevation.”
1. Loosen the two elevation nuts so the support sleeve can rotate.
2. Rotate the support sleeve so that the elevation indicator lines up
with the tick mark corresponding to the elevation setting you
recorded earlier.
Elevation
Indicator
3. Tighten both nuts.
Elevation
Nut
IMPORTANT
Make sure that you use the
elevation indicator and not
the nut to line up the
4
elevation. If your elevation is
not correctly set, you won’t
be able to obtain a signal.
Tick Marks
14 Preparing for Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast
Now that you have selected your site, and estimated
your cable needs, you need to select a mounting option
and mount the mast.
Take a moment to look through the available options
and select the one that best suits your installation site.
After you have selected a mounting option, and
successfully mounted the mast, you can go on to the
final section of this manual to complete the installation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on Solid Wood or Lap Siding
Mounting The Mast On Solid Wood Or
Lap Siding
Materials Needed
Tools Needed
• Electric drill with a
3/16" wood bit
• Bubble level
• 1/2" wrench
• 3/8" wrench
• 7/16" wrench
• Pencil
5
2
/16 x 3" lag screws
5
4
/16 x 2" lag screws
5
4
/16" washers
Important Considerations:
•
•
•
•
Make sure the wooden surface is structurally sound
Do NOT mount the dish where someone might use it as a handrail.
Do NOT mount the dish on any type of aluminum or vinyl siding.
Do NOT mount the dish on any type of composite paneling, such
as fiber board, particle board, or strand board.
DANGER
•
Do NOT mount the dish under an eave or overhang that may
block or partially shadow the dish.
AVOID Power Lines!
When following these
instructions, take
extreme care to avoid
contact with overhead
power lines, electric
lights, and power
circuits. Contact with
power lines, electric
lights, or power
circuits may be fatal. It
is recommended that
the dish be located
more than 20 feet from
overhead power lines.
16 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on Solid Wood or Lap Siding
Tip
Mounting Instructions
To locate a stud underneath
panel siding, locate the nails
securing the panel to the
wall. The nails usually align
with the center of the stud
and provide an easy guide.
1. Locate the center of a stud where you want to mount the mast
foot. Make sure you locate and secure the mounting foot to the
center of a wall stud. Do not mount the dish near the edge of
a stud.
2. Hold the mounting foot in a position so the center line is centered
on a stud or solid wood surface.
3. If you are mounting on a sloped or vertical surface, use a level to
verify that the center line is perfectly vertical.
Stud
level on center
line of template
Line center holes
on stud
Level
Not Level
Step 3: Make sure the mounting
Step 2: Center the foot on the stud.
foot is level.
4. Use a pencil to mark the two center holes and the four outside
corner holes of the mounting foot.
5. Remove the mounting foot and drill two 3/16" holes in the two
center hole locations and four 3/16" holes in the four outside
corner locations.
6. Use a wrench to loosen the nuts on the mounting foot so that you
can rotate the mast to access both of the center mounting holes.
7. Hold the mounting foot over the holes so that the top part of the
mast will rotate and point straight up.
Yes
Yes
No
Step 7: Make sure that the top of the mast will point straight up.
Mounting the Mast 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on Solid Wood
8. Install two 5/16" x 3" lag screws into the two center holes on the
mounting foot. Securely tighten the screws.
9. Put washers on the 5/16" x 2" lag screws, insert the screws into
the four outside holes and securely tighten them.
5/16" x 2" Lag Screws
5/16" x 3" Lag Screws
(For Sony Dish Installations
use (2) 3" x 1/4" Lag Screws)
5/16" x 2" Lag Screws
Steps 8 & 9: Inserting the lag screws.
10. Go on to the next section, “Final Installation,” to complete the
installation process.
Installing a Spacer
When the mounting foot spans two pieces of siding, it should be
positioned so most of the foot is on the top board. A spacer should be
installed to help hold the bottom of mounting foot in place. The spacer
can be made of either solid wood or plastic.
lap board
spacer
18 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on Brick or Poured Concrete
Mounting the Mast on Brick or
Poured Concrete
Materials Needed
Tools Needed
• Electric drill with
1/2" masonry bit
• Bubble level
• Screwdriver
• Hammer
4
double expansion anchors
• 7/16" wrench
• Pencil
4
machine screws
/16" washers
5
4
IMPORTANT Considerations
•
The wall anchors used must have a strength of at least 300
pounds of pull-out pressure. B4015 or equivalent double-
expansion anchors are recommended.
•
Do NOT mount the dish under an eave or overhang that may
block or partially shadow the dish.
Mounting Instructions
1. Hold the mounting foot in position on the mounting surface.
2. If you are mounting on a vertical or sloped surface, use a level to
ensure that the center line is vertical.
DANGER
AVOID Power Lines!
level on center
line of template
When following these
instructions, take
Level
extreme care to avoid
contact with overhead
power lines, electric
lights, and power
Not Level
circuits. Contact with
power lines, electric
lights, or power circuits
may be fatal. It is
Step 1: Hold the mounting
Step 2: Make sure the mounting
foot in position.
foot is level.
recommended that the
dish be located more
than 20 feet from
3. Mark the four outside holes on the mounting foot.
4. Remove the foot and drill four (4) 1/2" holes in the locations
you marked.
overhead power lines.
Mounting the Mast 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on Brick or Poured Concrete
5. Insert four (4) double-expansion anchors.
6. Use a wrench to loosen the nuts on the mounting foot so you
have easier access to the mounting holes.
7. Hold the mounting foot over the holes so the top part of the mast
will rotate and point straight up.
Yes
No
Step 7: Make sure that the top of the mast will point straight up.
8. Insert and tighten the machine screws.
9. Go on to the next section, “Final Installation,” to complete the
installation process.
Mounting the Mast on a Hollow
or Cinder Block Wall
Materials Needed
Tools Needed
• Electric drill
with 1/2"
masonry bit
1
• Bubble level
• Screwdriver
• 7/16" wrench
• Pencil
4
/4" hollow wall
togglers
4 machine screws
/16" washers
5
4
IMPORTANT Considerations
•
Do NOT mount the dish under an eave or overhang that may
block or partially shadow the dish.
20 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on a Hollow or Cinder Block Wall
DANGER
Mounting Instructions
AVOID Power Lines!
1. When installing togglers in cinder blocks, it is important to
position them in the core of the block. To position the foot on the
wall, measure 7-1/2" from one edge of the block and mark the
center of the block.
When following these
instructions, take
extreme care to avoid
contact with overhead
power lines, electric
lights, and power
2. Center the mounting foot on the mark you made.
3. Level the center line of the mounting foot using a bubble level.
circuits. Contact with
power lines, electric
lights, or power
level on center
line of template
circuits may be fatal. It
is recommended that
the dish be located
more than 20 feet from
overhead power lines.
Level
Not Level
7 1/2"
4. Mark the four outside corner holes.
5. Remove the mounting foot. Drill a 1/2" hole at the marked
locations.
6. Install the togglers:
a. Carefully fold one end of the metal channel along the plastic
straps. Hold the metal channel flat against the plastic straps
and slide it through the hole.
Wall
Metal channel
Fold in
Step 6a: Slide the metal channel through the hole.
b. Pull the ring so the metal channel rests flush behind the wall.
Hold the ring tight and slide the plastic cap along the straps
until the cap is flush with the wall.
Wall
Plastic cap
Metal
chann
Ring
Step 6b: Make sure the plastic cap is flush with the wall.
Mounting the Mast 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Dish on a Hollow or Cinder Block Wall
c. Push the straps side-to-side to snap them off flush with the wall.
Step 6c: Snap off straps flush with the wall.
d. Repeat for all four holes.
7. Use a wrench to loosen the nuts on the mounting foot so you
have easier access to the mounting holes.
Yes
No
Step 8: Make sure that the top of the mast will point straight up.
8. Hold the mounting foot over the holes so the top part of the mast
will rotate and point straight up.
9. Place washers on each of four #20, 1/4" x 3" machine screws and
attach the mounting foot to the wall. Securely tighten the screws.
10. Go on to the next section, “Final Installation,” to complete the
installation process.
22 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Dish on a Pole
Mounting the Dish On A Pole
Tools Needed
• Bubble level
• Screwdriver
• Hammer
Materials Needed
• (1) 1-1/4" inner diameter
Schedule 40 galvanized
steel pipe with a measured
outer diameter of 1.6"
• Hacksaw
• (3) bags quick-setting
concrete
• Shovel or post hole
digger
• Pencil
Important Considerations:
•
•
•
Do not install the pole in wet or marshy areas.
The pole must go at least 3 feet below the surface.
If the length of pipe above ground is too long, guy wires may be
needed to increase the stability of the mount in windy conditions.
•
•
You will need to ground the pole in addition to the dish and
coaxial cable.
The pole that has been secured in the ground with concrete
replaces the mounting foot and mast assembly that was supplied
with the dish. The dish is held on the pole by the sleeve of the
LNB support arm.
Mounting Instructions
1. Dig a hole 36" deep and 8" to 12" wide at the mounting location.
DANGER
The depth of the hole must extend at least 6" below the frost line.
For most installations, a pole 6' long is sufficient, since this allows
3' of the pole to be below the ground and 3' above ground.
AVOID Power Lines!
When following these
instructions, take
extreme care to avoid
contact with overhead
power lines, electric
lights, and power
circuits. Contact with
power lines, electric
lights, or power
circuits may be fatal. It
is recommended that
the dish be located
more than 20 feet from
overhead power lines.
at least 3'
8"-12"
Mounting the Mast 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Dish on a Pole
2. Use a hacksaw to cut a 45o angle at the bottom of the pole. This
will prevent the pole from rotating in the concrete over time.
45° cut
3. Place the pole in the hole and use a small amount of dirt or stones
to hold the pole upright. You need to attach guy wires to help
keep the pole upright.
4. Level the pole using the bubble level. Level the pole at two
different locations that are at right angles to each other.
Top view of pole
Put level in 2 places at right
angles to each other
pole
Level
Not Level
5. Fill the hole with quick drying cement. Stop when the cement is
about two inches from the top of the hole.
6. Let the cement completely dry before you mount the dish on
the pole.
7. Go on to the next section, “Final Installation,” to complete the
installation process.
24 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on a Roof
Mounting the Mast on a Roof
IMPORTANT
Use the roof mount only as a last resort. You can easily
damage the roof by walking on it or cause leaks by not
properly sealing the mounting holes. Problems with roof
installations increase with the age of the roof and the type of
roofing materials.
Tools Needed
• Electric drill with a
5
2
/16 x 3" lag screws
3/16" wood bit
• Bubble level
• 1/2" wrench
• 3/8" wrench
• 7/16" wrench
• Ladder
5
4
/16 x 2" lag screws
• Pencil
5
4
/16" washers
Important Considerations:
•
•
•
Do not mount the dish on slate or shake shingles.
Do not mount the dish on an overhang.
On a flat roof, do not mount the dish in a place where water
collects.
Step-by-step Instructions for Mounting the Mast
on a Roof
DANGER
AVOID Power Lines!
1. Locate the center of a rafter where you want to place the
When following these
instructions, take
mounting foot.
rafters
extreme care to avoid
contact with overhead
power lines, electric
lights, and power
facing
board
circuits. Contact with
power lines, electric
lights, or power
circuits may be fatal. It
is recommended that
the dish be located
more than 20 feet from
overhead power lines.
nails
Step 1: Locate where you want the mounting foot to be placed.
Mounting the Mast 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Mast on a Roof
2. Hold the mounting foot in a position so the center line is centered
on a rafter.
3. Use a bubble level to make sure the center line is perfectly vertical.
Level on center
line of template
Level
Not Level
Steps 2 & 3: Center the mounting on a rafter and make sure that it is level.
4. Use a pencil to mark the six holes in the mounting foot.
5. Remove the mounting foot and drill a 3/16" hole in the two center
line locations you marked.
6. Drill four 3/16" holes in the four outside corner locations you
marked.
7. Fill all six holes with a small amount of roof sealant.
8. Use a wrench to loosen the nuts on the mounting foot so you
have easier access to the mounting holes.
9. Hold the mounting foot over the holes so the top part of the mast
will rotate and point straight up.
10. Use two 5/16" x 3" lag screws in each of the center line holes to
attach the mounting foot to the roof. Secure the four outside
corner holes with four 1/4" x 2" lag screws. Securely tighten all
six screws.
11. Seal the mounting foot with roof sealant. When applying the
sealant, make sure you seal the areas shown in the figure below.
Sealant
No
Yes
Step 11: Seal the mounting foot to
Step 9: Make sure the top part of the
avoid water leakage.
mast points straight up.
12. Go on to the next section, “Final Installation,” to complete the
installation process.
26 Mounting the Mast
Download from Www.Somanuals.com. All Manuals Search And Download.
Final Installation
This section contains the final steps necessary to get
the signal from the satellite dish to your satellite
receiver.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Leveling the Mast
Leveling the Mast
Leveling the mast is one of the most important steps in installation.
If the mast is not level, the elevation and azimuth settings will not be
accurate. This will make it difficult to obtain the satellite signal.
The mast must be level in both the side-to-side and the front-to-back
directions. Side-to-side leveling determines whether the mounting foot
is level. Front-to-back leveling determines whether the mast is level.
Leveling Side-to-Side
1. If you mounted the mast on a vertical surface, such as a wall, you
leveled the mast side-to-side when you mounted the mast foot.
Skip to “Leveling Front-to-Back” on the next page.
2. To check whether the mast is level side-to-side, place a bubble
level on the mast as shown in the figure below.
3. Is the bubble centered in the level’s window?
If YES — Continue to “Leveling Front-to-Back”.
If NO —
a) If the bubble is not centered, determine which side of the
mounting foot needs to be raised.
b) Unscrew the lag or machine screws from that side of the
mounting foot.
c) Place washers between the mounting foot and the mounting
surface. Use enough washers to level the mounting foot.
d) Secure the mounting foot with the lag or machine screws.
CAUTION
Level Not Level
Use caution when
installing, adjusting or
dismantling the dish
and mast. The weight
of the dish may cause
the dish and mast to
swing down and strike
you, a bystander or
nearby objects. This
could cause personal
injury or damage to
the dish. Never insert
your fingers inside the
mast. Always grip the
mast around its outside
circumference.
Step 3: If the mast is not level, add
Step 2: Verify that the mast is level
washers to level the foot.
side-to-side.
28
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Final Dish Assembly
Leveling Front-to-Back
1. Loosen the two bolts securing the mast to the mounting foot so
the mast moves freely.
2. Place a bubble level on the mast as shown in the figure. Move the
mast so the bubble is centered in the level’s window.
Level Not Level
Level Not Level
Rotate mast as needed
Adjustment
Rotate mast as needed
Adjustment
Step 2: Verify that the mast is level front-to-back.
3. Tighten the two bolts securing the mast to the mounting foot.
Final Dish Assembly
1. Place the dish-LNB arm assembly on top of the mast (or pole).
Step 1: Place the dish assembly
Loosen the mast clamp and lower
reflector onto the mast. Tighten the
clamp screws.
Sony Step 1:
on the mast or pole
2. Find the length of RG-6 coaxial cable with messenger (ground)
wire that will extend from the satellite dish to the cable’s point of
entry into the building.
If your total RG-6 coaxial cable length from the dish to the receiver
is more than 112 feet, you may need an additional installation
component, such as a line amplifier, to compensate for the longer
cable length.
Final Installation 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Final Dish Assembly
3. Separate the messenger (ground) wire from the coaxial cable.
Tip
Separate only the amount required to install the coaxial cable
through the LNB arm. (Sony dish owners skip to next step.) Push
only the coaxial cable through the bottom of the mast and out the
top. Pull about 2 feet of cable out of the top. Loop the cable and
push it through the LNB support arm as shown below.
If you have a dual-output
LNB, and are planning to
connect your dish to two
separate receivers, you
should route both cables at
this time.
4. Place some silicone grease on the LNB connector and connect the
end of the coaxial cable to the LNB. (Sony dish owners: clip the
coaxial cable to the LNB arm and skip to step 8.)
RG-6 Coaxial
Cable
Messenger (Ground) Wire
Step 3: Route the cable
Step 4: Connect the coaxial cable
through the mast.
to the LNB.
5. Insert the end of the LNB into the end of the LNB support arm
(push any extra coaxial cable back through the support arm).
Tip
The hex retainer nut must
be inserted into the top of
LNB before the phillips head
screw is inserted into the
bottom of the LNB.
Otherwise it is very difficult
to thread the screw to the
nut.
6. Locate the special hex retainer nut and insert it into the LNB
mounting hole on top of the LNB support arm.
7. Locate the phillips head screw and insert it into the LNB mounting
hole from the bottom of the LNB support arm. Tighten the screw
with a screwdriver
8. Locate the grounding hardware (bolt, star washer and nut).
9. Insert the bolt as shown below and attach the messenger (ground)
wire to the foot of the mast (you may want to trim the extra
messenger wire before attaching). You will connect the other end
of that wire to the grounding block at the building entry point.
Note
Wire
When using a pole mount,
you need to attach
NUT (insert first)
Hex head bolt
the grounding wire to the
metal pole using a 1 1/2”
grounding clamp.
Star washer
BOLT
Nut
Step 9: Attach the messenger (ground)
wire to the mast foot with the nut,
star washer and bolt.
Steps 5-7: Secure the LNB to support.
30
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
A Few Words About Grounding the System
IMPORTANT
A Few Words About Grounding
the System
The United States
National Electrical
Code specifies that
coaxial cable that is
exposed to lightning
shall be connected to
the grounding system
of the building as close
to the point of cable
entry as possible.
Grounding the satellite system to the central building ground helps
protect it and other components from lightning damage. Different
brands of satellite systems may have special grounding requirements.
However, dish installation should comply with local codes and the
National Electrical Code (NEC). Refer to your satellite system’s user
guides for any other additional grounding information. Grounding the
satellite system is something you can probably do yourself. But if
you’re not sure, you should contact a qualified electrician.
Acceptable central building ground points
•
Grounded interior metal cold water pipe within five feet of the
point where it enters the building.
•
•
•
Grounded metallic service raceway.
Grounded electrical service equipment enclosure.
Eight-foot grounding rod driven into the ground (only if bonded to
the central building ground by #6 or heavier bonding wire).
•
Other acceptable grounding electrodes that comply with sections
250 and 810 of the National Electrical Code (NEC).
Routing and Grounding the Cables
1. Attach the grounding block to the side of your house close to the
point you have chosen as the coaxial cable entry point. You may
have to use anchors, togglers, or wood screws depending on the
surface on which you are mounting the grounding block.
CAUTION
It is extremely
important to ground the
dish AND the coaxial
cables to a single point
in the central building
ground. A nearby
lightning strike can
easily damage an
ungrounded dish, the
receiver and your TV.
Connecting both ground
wires to the same point
in the central building
ground meets code
requirements and
Step 1: Attach the grounding block to side of your house at
your designated entry point.
provides the best
protection for your
equipment.
Final Installation 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Routing and Grounding the Cables
2. Route the coaxial cable and messenger (ground) wire from
the bottom of the mast to the grounding block.
Cable Routing Tips
• If you are routing the
grounding wire along the
ground, make sure the
wire is buried deep
3. Make a 3”- 5” drip loop using cable clips at the grounding
block as shown. This will prevent water from running into
the connection at the grounding block.
enough so that it will not
be damaged or uncovered.
4. Place some silicone grease on the connector and connect the
coaxial cable to the grounding block
• If you are routing the
wire or cable above the
ground, use cable clips to
secure the two to a wall
or surface.
5. Secure the messenger (ground) wire to the grounding block,.
6. Locate the central building ground (see the list of acceptable
central building grounds on the preceding page).
• Make sure you route the
grounding wire in an area
where people or animals
are not likely to come in
contact with the cable.
7. Locate the grounding wire (#10 copper or #8 aluminum) that
will extend from the grounding block to the central building
ground. Attach the grounding wire to the grounding block
by placing it through the wire hole in the grounding block
and tightening the screw.
8. Route the grounding wire from the grounding block to the
central building ground, and connect to the central building
ground.
Step 2: Route cable from dish.
Step 3: Make a drip loop.
Steps 7 & 8: Connect the #10 copper or
#8 aluminum grounding
Step 4 & 5: Connect the coaxial cable
wire and route to the
and the messenger wire to
central building ground.
the grounding block.
32
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Running a Cable into the House
Running Cable Into the House
1. Drill a hole in the location you want the coaxial cable to enter.
2. Place some silicone grease on the connector and connect the
RG-6 coaxial cable that will extend from the grounding block
to the receiver.
CAUTION
Before drilling, make
sure there are no wires
or pipes behind the
wall in the area of the
hole.
3. Make a 3” - 5” drip loop using cable clips at the grounding
block.
4. Route the coaxial cable through your house to the back of the
receiver. You may route the coaxial cable through a floor or
wall or directly to the back of the receiver. If you are routing
through a wall, you may choose to install a wall plate at the
point the coaxial cable enters the inside of the house and use
a third RG-6 coaxial cable.
5. Use a silicone sealant to seal all outside connections and the
hole you drilled for the coaxial cable to enter your house.
Step 4: Route the cable
into your house.
Step 3: Make a drip loop.
Cable Entry Overview
Grounding Block
Cable entry into house
Step 2: Connect RG-6 cable to
grounding block.
RG-6 coaxial cable #2
(no messenger wire)
DSS receiver
TV
To Telephone Outlet
Final Installation 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Final Connections
Making the Final Connections
1. Connect the RG-6 coaxial cable to the SATELLITE IN jack at the
back of the receiver as shown. DO NOT connect the coaxial
cable to the IN FROM ANTENNA jack!
About the Phone
Connection
2. Take a phone off the hook to prevent electric shock from
incoming calls.
The satellite receiver calls a
telephone number once a
month or so to update your
access card. It is also used
to order pay-per-view
3. Connect a phone cord from the back of the receiver to a
phone jack.
events. These calls only
take a few seconds.
Step 1: Connect the RG-6 cable to the SATELLITE IN
jack on the back of the receiver.
PHONE JACK
SATELLITE IN
Step 2 & 3: Take the phone off the hook
before you connect a phone
cord from an outlet to the
back of the receiver.
34
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquiring and Fine Tuning the Signal
Maximum Signal
Strength
Now that you have installed the satellite antenna and routed all of the
cable, it’s time to acquire and fine tune the signal. Before you begin,
you may want to go outside and double-check the azimuth and
elevation settings on the dish.
While the maximum signal
strength is 100, the signal
strength you achieve will
probably be less. Although
there is no difference in
picture quality between a
signal strength of 60 and
85, the higher the signal,
the less likely you are to
experience signal outages
during adverse weather.
•
Make sure that the elevation indicator (the edge of metal, not the
washer or the bolt) is aligned to the correct elevation.
•
Use a compass to verify that the azimuth setting on the dish
is correct.
When you are confident that the settings are correct, bring up the
“Dish Pointing” menu again and use the signal meter to see if you are
getting a signal. Once you have acquired the signal, you’ll want to
make some fine-tuning adjustment to the dish in order to obtain the
highest possible signal.
Tip
You can adjust your TV’s
volume to hear the signal
meter from the dish
Refer to your receiver manual for dish pointing information.
If you are not receiving a signal, you need to incrementally adjust the
azimuth setting on the dish. After you receive a signal, you will want
to continue to adjust the azimuth to try to get the best possible signal.
location, or you may want a
friend to watch the signal
meter and relay the
strength to you.
Final Installation 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquiring and Fine Tuning the Signal
Adjusting the Azimuth and Elevation Settings
1. Using a compass, rotate the dish so that the LNB arm points to
the correct azimuth heading. Loosen the support sleeve nuts
as needed. (Sony dish owners loosen the mast clamp screws.)
Point LNB arm in the exact
Support
azimuth direction according
Sleeve
to your compass
Nuts
2. If you do not hear a continuous tone from the signal meter, use
the following procedure to adjust the dish until you hear one
continuous tone:
•
At the top of the mast is a piece of tape
with evenly spaced tick marks. Carefully
rotate the dish one tick mark to the right
and pause for 3-5 seconds.
Line edge of bracket
up with tick marks
•
If you do not hear a continuous tone, rotate
the dish back to the original position and
then one tick mark to the left and pause for
3-5 seconds.
Support
Sleeve
Nuts
ROTATE LEFT
One tick mark
ROTATE RIGHT
One tick mark
HANDS OFF
•
Continue rotating the dish one tick mark at a time further
right and left from center (making sure to pause for 3-5
seconds at each position) until you hear the continuous
tone, and the highest signal meter reading.
4. After you get a signal, continue adjusting the azimuth by
rotating the dish in small increments left and right until you
achieve the highest possible strength.
5. Tighten the support sleeve nuts so the dish won’t rotate left
and right.
36
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquiring and Fine Tuning the Signal
6. Slightly loosen the elevation nuts on the LNB support arm so you
can adjust the dish up and down.
7. Adjust the elevation of the dish upward and downward until you
achieve the highest possible signal strength:
Elevation
Adjustment
When setting the elevation,
be sure to line up the
elevation setting with the
elevation indicator and not
the bolt.
Use the edge of the
metal here to line up the
elevation
Do not use this
to line up the
elevation
4
•
•
Move the dish upward one tick mark, pause for 5
seconds, and check the signal strength.
Move the dish downward (back to the original elevation
setting) and then move down one tick mark, pause for
five seconds, and check the signal strength.
Elevation nut
TILT UP
One tick mark
TILT DOWN
One tick mark
HANDS OFF
8. When you achieved what you believe to be the highest signal
strength (peak signal), tighten the elevation nuts on the
support arm.
Ordering Programming
After you have obtained and fine tuned the satellite signal, the
last step you need to complete is to call the program providers to
order programming, and then review the satellite receiver’s
instruction manual for information about using all of the great
features it offers.
Final Installation 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Can’t Pick Up the Satellite Signal
Most problems with signal acquisition can be traced to one of these points: improper cabling
and connections or inaccurate positioning and pointing of the dish.
Cabling and Connections Problems
1. Make sure you’re using the proper type of RG-6 coaxial cable to connect the LNB to the grounding
block and the grounding block to the satellite receiver. Standard Cable TV coaxial cables (RG-59)
will NOT pass the satellite signals properly. Important: Do NOT connect the RG-6 cable from
the dish or grounding block to any existing TV cable in your house. Do not use conventional TV
splitters. They will not pass the satellite signals.
2. Make sure the access card is fully inserted into the access card slot.
3. Check all cable connections to make sure they are securely fastened to the proper connectors,
from the TV, to the satellite receiver, all the way out to the dish LNB. Make sure the coaxial
cable connector center conductor is not bent or broken.
4. Make sure the cable from the dish to the receiver is connected to the SATELLITE IN jack on the
back of the receiver (NOT the ANTENNA IN jack).
Dish Positioning and Pointing Problems
1. Verify that you are using the correct azimuth and elevation for your city by using the dish
pointing menu.
2. Make sure the dish is physically set to the correct elevation according to the dish pointing menu.
•
•
Make sure the dish mast is level.
Make sure the elevation indicator (edge of metal, NOT the washer or the bolt) is aligned to
the correct elevation.
3. Use a compass to verify that the LNB support arm is pointed toward the correct azimuth
reading (number) as indicated by the dish pointing menu. Nearby metal objects may cause a
compass to give an inaccurate reading.
4. Make sure there are no obstructions (trees, buildings, windows, your body or hands, etc.) that
might be blocking the satellite signal.
5. Slowly rotate the dish left or right (one tick mark at a time) pausing at each for 3-5 seconds
until the on-screen signal meter produces one continuous tone.
6. If you can’t acquire a signal by rotating the dish left and right, readjust the elevation of the dish.
•
•
Return the LNB support arm to the original azimuth (left-to-right compass direction).
Loosen the elevation nuts on the LNB support arm and position the dish upward or
downward (one tick mark at a time). When finished, retighten the nut.
38
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Temporary Satellite Signal Loss
If you lose the satellite signal temporarily, the problem can usually be traced to one of these points:
1. Rain Fade. Rain fade is a normal, temporary loss of a satellite signal due to the inability of the
satellite signal to penetrate unusually heavy, rain-filled clouds, rainfall, or snowfall. Rain fade
tends to be brief, lasting only as long as the heavy cloud condition persists.
To minimize rain fade effects, maximize your signal strength. Then, when rain fade occurs, you
have the best chances of having a signal that is still strong enough to view.
Make sure the dish is mounted securely. The strong winds that often accompany heavy
rainstorms can move the dish out of position if it is not mounted securely.
Also, heavy/wet snow and ice build up on the dish can block the satellite signal until the build
up is removed.
2. Overheated Components. The satellite receiver must receive adequate ventilation to work
safely and properly. If the receiver overheats, the satellite signal may deteriorate until adequate
ventilation is restored. Do not stack VCRs or other components on top of the satellite receiver.
You hear a dialing sound while talking on the phone
(If the Satellite Receiver is Connected to a Phone Line)
Your satellite receiver may be attempting to call the billing center. Under normal conditions, the
receiver hangs up any time it detects what it interprets as a voice on the line. After four unsuccessful
attempts to get a dial tone, the receiver is designed to call out regardless of the status of the line. If
you’re using the phone when the receiver calls out, you’ll hear a dialing sound. Don’t worry: your
phone connection will not be broken.
Dish Pointing Steps
Step 1: Are you receiving a signal?
•If yes, go to Step 4.
•If no, proceed to Step 2.
Step 2: Adjust the azimuth right or left. Are you now receiving a signal?
•If yes, go to Step 4.
•If no, proceed to Step 3.
Step 3: Adjust the elevation up or down 1 tick. Are you now receiving a signal?
•If yes, proceed to Step 4.
•If no, return to Step 1.
Step 4: Carefully adjust the azimuth (left or right) and the elevation (up or down) until the peak
signal is achieved. When finished, tighten the azimuth and elevation bolts.
Final Installation 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Digital Satellite System Installer's Reference
Thomson Consumer Electronics (Digital Satellite Systems)
Support Line
Digital Satellite System Service Support Line 1-800-679-4776
Call this number to resolve service and use and care questions.
Program Providers
DIRECTV
Customer Service 1-800-347-3288
Use this number to resolve programming and billing inquiries and to deactivate service.
Installer Activation 1-800-277-4388
Use this number to activate a newly installed system.
USSB
Customer Service 1-800-204-8772
Use this number to resolve programming and billing inquiries and to deactivate service.
Installer Activation 1-800-883-8772
Use this number to activate a newly installed system.
Digital Satellite System Publications
Publication/Description
Publication number
T-DSSPREWIRE-1
T-8743CM
New Home "Prewiring" & Distribution Systems
Accessories and Antenna Components Catalog
To obtain the publications listed above contact:
Thomson Consumer Electronics
10003 Bunsen Way
Louisville, KY 40299
Telephone: 502-491-8110
40
Final Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index
G
P
A
Ground wire, separating 30
Grounding block 12
Grounding the system
house entry point 31
Grounding wire 32
Phone connection 34
Plastic dish
Acceptable central building
ground points 31
Acquiring the satellite signal 35
Azimuth setting, adjusting 36
putting together 14
Precise site survey 9
C
R
L
Cable, routing
RG-6 coaxial cable
drip loops 32
routing into house 33
Roof mount
into the house 33
through the mast 30
Central building ground 11, 31
acceptable points 31
CH3/CH4 switch 7
Compass, using 9
Lap siding mounting option
use of a spacer 18
LNB
attaching to the LNB support
arm 30
sealing the mounting foot 26
Roof mounting option
considerations 25
connecting the RG-6 coaxial
cable 30
Connecting the dish to the
receiver 34
S
M
Site survey 9
Support sleeve 14
Mast, leveling 28
Messenger (ground) wire 30
Metal dish
D
Dish, final assembly 29
Dish pointing steps 39
Double-expansion anchors 19
Drip loop 32
T
putting together 14
Mounting options
Brick or poured concrete 19
Hollow or cinder block wass 20
Pole mount 23
Troubleshooting
signal acquisition for system
test 38
E
Elevation
Roof 25
setting 14
Solid wood or lap siding 16
Elevation angle 9
Elevation nuts 14
Elevation setting, adjusting 37
N
National Electrical Code (NEC)
11, 31
F
Fine-tuning the satellite signal
adjusting the azimuth 36
Final Installation 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
10330 North Meridian Street
Indianapolis, IN 46290
©1998 Thomson Consumer Electronics, Inc.
Trademark(s)® Registered
Marca(s) Registrada(s)
Printed in USA
TOCOM 15347490
Download from Www.Somanuals.com. All Manuals Search And Download.
|