Television
User’s Guide
Changing Entertainment. Again.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRTUC
a
T
b
IOl
N
e
S
of Contents
Read before operating equipment
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
15. If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Section 810
of the National Electrical Code, ANSI/NFPA No. 70-1984
(Section 54 of Canadian Electrical Code, Part 1) provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-
in wire to an antenna-discharge unit, size of grounding
conductors, location of antenna-discharge unit,
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
connection to grounding electrodes, and requirements
for the grounding electrode. See following example.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
ANTENNA
LEAD IN
WIRE
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
ELECTRIC SERVICE
POWER SERVICE GROUNDING
EQUIPMENT
ELECTRODE SYSTEM
(NEC ART 250, PART H)
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-
supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Information .................................................... 2
IMPORTANT SAFETY INSTRUCTIONS................................ 3
Chapter 3: Using the Menu System................21
The Basic Menu System.................................................. 21
Sound Menu ............................................................. 21
Picture Menu ............................................................ 21
Channel Guide Menu............................................... 21
Parental Control Menu ............................................ 22
Time Menu................................................................ 22
Language & CC Menu .............................................. 23
The TV can be "Decommercialized"............................... 23
Chapter 1: Connections & Setup
5
Chapter 1: Connections & Setup.......................5
Things to Consider Before You Connect ......................... 5
Protect Against Power Surges ................................... 5
Protect Components from Overheating ................... 5
Position Cables Properly to Avoid Audio
Interference................................................................ 5
Important Stand and Base Safety Information......... 5
Use Indirect Light ....................................................... 5
Things to Consider Before You Connect................... 5
Chapter 4: Using the TV's Features.................24
Channel Banner............................................................... 24
Parental Controls and V-Chip......................................... 24
Explanation of Jacks and Cables...................................... 6
The Front of Your TV......................................................... 8
Front Input Jacks ........................................................ 8
Front Panel Buttons .......................................................... 8
Plug in the TV............................................................. 8
Start-up.............................................................................. 8
Put Batteries in the Remote ...................................... 8
Turn on the TV............................................................ 9
Place All Available Channels Into Memory .............. 9
Set the Time ............................................................... 9
The ClonePRO™ ............................................................... 9
Understanding the Menus ............................................ 10
Master Menus........................................................... 10
Basic Menus .............................................................. 10
Using Master and Basic Menus...................................... 10
Exiting a Menu ......................................................... 10
Setting Limits in Master Menus............................... 10
Sound Menu.................................................................... 11
Picture Menu ................................................................... 12
Access and Power Options Menu .................................. 12
Parental Control.............................................................. 14
Time Menu....................................................................... 15
Setup Menu..................................................................... 16
How V-Chip Works ................................................... 24
USA V-Chip Rating System....................................... 25
Canadian English V-Chip Rating System ................. 25
Canadian French V-Chip Rating System.................. 26
USA V-Chip TV Rating Limit ................................... 26
Blocking Specific Content Themes .......................... 28
Viewing Specific Content Themes........................... 28
Blocking Canadian V-Chip Ratings.......................... 28
V-Chip Movie Rating Limit....................................... 29
V-Chip Exempt Program Block .............................. 29
KidPass ...................................................................... 30
Front Panel Lock....................................................... 30
Create Password....................................................... 30
Chapter 5: Other Information .........................31
Using the ClonePRO™ .................................................... 31
Modes of operation ................................................. 31
DSCI mode ................................................................ 31
IR mode..................................................................... 32
Cloning a TV ............................................................. 33
Troubleshooting.............................................................. 34
Limited Warranty............................................................ 37
Accessories ...................................................................... 39
Chapter 2: Using the Remote Control
17
Chapter 2: Using the Remote Control ............17
Types of Remote Controls .............................................. 17
Basic Remote Buttons (CRK17TC1 & CRK17TD1)........... 17
Additional Remote Buttons (CRK17TD1)....................... 18
Using the INPUT Button.................................................. 19
Using the SYSTEM Button.............................................. 19
ClonePRO™ Remote Buttons ......................................... 20
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Connections & Setup
Things to Consider Before You Connect
Protect Against Power Surges
•
•
•
Connect all components before you plug any of their power cords into the wall outlet.
Turn off the TV and/or component before you connect or disconnect any cables.
Make sure all antennas and cables are properly grounded. Refer to the Important Safeguards
sheet packed with your TV.
Protect Components from Overheating
•
Don’t block ventilation holes on any of the components. Arrange the components so that air
can circulate freely.
•
•
•
Don’t stack components.
If you place components in a stand, make sure you allow adequate ventilation.
If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it
won’t flow around other components.
Position Cables Properly to Avoid Audio Interference
•
Insert each cable firmly into the designated jack.
•
If you place components above the TV, route all cables down the side of the back of the TV
instead of straight down the middle of the TV.
•
If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate
size and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled off.
This could cause personal injury and/or damage the TV. Refer to the Important Safeguards sheet
packed with your TV.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or
indirect lighting.
Things to Consider Before You Connect
You will need a master remote or ClonePRO™ to set up the TV. Go to the accessory page at the
back of this manual or contact your RCA commercial distributor to purchase these.
Graphics contained within this publication are for representation only.
Chapter 1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
DSCI
Port
DSCI
Port
TV ANT
TV ANT
Model J32F635
Models J24F635 and J27F635
Explanation of Jacks and Cables
This manual covers TV models that have different back panels. Match the back panel of your TV to one of the back panels
shown. This section describes the jacks you can use to make connections. There are several ways to connect components to
your TV.
VIDEO 1
VIDEO, AUDIO R and L/MONO INPUTS Used to connect components such as a
VCR, DVD player, camcorder, laserdisc player or video game consoles with audio/video
outputs. These jacks are used for most audio/video connections between components.
Note: If your component has only one input for audio (mono), connect it to the left
(white L/Mono) audio jack on the TV and don't connect the right audio part of the
cable.
Audio/Video Jacks
•
•
•
•
R (RIGHT) AUDIO Provides right audio connection. The right audio connector is
usually red.
L/MONO AUDIO Provides left audio connection. The left audio connector is
usually white.
VIDEO Provides composite video connection. The video connector is usually
yellow.
S-VIDEO Provides better picture quality than the video jacks because the color part
of the signal is separated from the black and white part of the picture. When using
S-VIDEO IN, make sure to connect left and right audio cables to the L/MONO and R
AUDIO Input jacks (an S-Video cable is required).
•
TV ANT Used to attach either an antenna or cable system to the TV. To connect a
VCR, connect a coaxial cable to the TV ANT jack on your TV and to the Output Jack
on the VCR (sometimes labeled OUT TO TV).
TV ANT
Continues on next page...
6
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
VIDEO 2 (Model J32F635 only)
VIDEO, AUDIO R and L/MONO and Y, Pb, Pr INPUTS Let you connect a second
component video source, such as a DVD player.
•
•
Y, Pb, Pr Provide optimum picture quality because the video is separated into three
signals. Use three video-grade cables for the connection. When using Y, Pb, Pr, make
sure to connect left and right audio cables to the VIDEO 2 AUDIO Input jacks.
R and L/MONO AUDIO and VIDEO Their description is the same as VIDEO 1.
MONITOR OUT
AUDIO/VIDEO OUTPUTS Allow connection of external audio amplifiers, power
speakers, audio receivers for improved sound quality or an external video monitor with
the use of VIDEO OUT. Please note that these outputs cannot drive standard speakers
directly.
DSCI PORT This port is used to transfer information between a TV and other devices,
such as a clone box or interactive system. This port is an eight-pin telephone-type port.
When the TV receives a message via the DSCI (digital serial communications interface)
port, it will act in accordance with the digital instructions received. For more information
on its connection and operation, please contact your distributor or the supplier of the
interactive system.
EXTERNAL SPEAKERS These jacks are used to connect your TV to a mono speaker. If
you want to deliver TV audio into another room, connect the external speaker directly to
the TV using class 2 speaker wire.
Note: Speakers should have a minimum of 16 ohms impedance.
Chapter 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
The Front of Your TV
Front Input Jacks
The TV has front input jacks for your convenience: one set of audio/video
inputs, an s-video and a headphone jack. These jacks are towards the
front of the TV on the side. To access the component you connected to
the front of the TV, press the INPUT button on your remote until FRNT
appears on the screen. The jacks are ideal for connecting a video game
console or a camcorder.
Note: When connecting a component that only has one audio jack,
such as some camcorders, use the TV’s AUDIO L/MONO jack to hear
the audio.
VIEW
HEAR
VOICE
STOP
M
E
N
U
/
O
K
C
H
CH
VOL
VOL
POWER
MESSAGE
ALARM
R
E
A
D
Y
A
D
V
I
S
O
R
Y
WATCH
WARNING
H-PHONE Allows you to connect headphones to listen to the sound
coming from the TV.
AUDIO
L/MONO
VIDEO
R
H-PHONE
L/MONO and R AUDIO Receives audio from another component such
as a VCR, camcorder, or video game console.
VIDEO Receives video from another component such as a VCR,
camcorder, or video game console.
S (S-Video) if equipped Provides better picture quality when receiving
s-video from another component. When using S-VIDEO IN, make sure to
connect left and right audio cables to the L/MONO and R AUDIO Input
jacks (an S-Video cable is required).
Front Panel Buttons
If you cannot locate your remote, you can use the front panel buttons of your TV to operate many of the TV’s features.
MENU/OK Brings up the Main menu. In the menu system, it selects highlighted items.
CH v Scans down through the current channel list. In the menu system, acts like the down arrow button on the remote
control and adjusts menu controls.
CH
Scans up through the channel list. In the menu system, acts like the up arrow button on the remote control and
adjusts menu controls.
VOL < Decreases the volume. In the menu system, acts like the left arrow button on the remote control and adjusts menu controls.
VOL > Increases the volume. In the menu system, acts like the right arrow button on the remote control and adjusts menu controls.
POWER Turns the TV on and off.
Start-up
The steps below get your TV connected and ready to watch.
Plug in the TV and Turn it On
Plug the end of the power cord into a grounded wall outlet. Insert the plug completely into the outlet. Press POWER on the
TV or remote.
Put Batteries in the Remote
1. Slide off the cover of the battery compartment.
2. Place the two AAA batteries into the remote, matching the + and – end of each battery in the compartment.
3. Replace the cover.
8
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Place All Available Channels Into Memory
AUTO CHANNEL SEARCH
1. To go to the Setup menu, with the master remote (CRK17TD1), press
MENU then select Setup. In this menu you'll be able to set your
Signal Type. Next go to Auto Channel Search, the TV will search for
all channels viewable through your antenna or cable TV system.
Go Back
Channel List
List A...
Running...
012
Start
2. Select which channel list you’d like to find channels for (List A is the
default).
Channel
Press OK to start the
Auto channel search
3. Press the down arrow button to select Start. Press the OK button to
start searching. The TV searches for active channels and places them
in the channel list.
Note: Video Input Channels (VID, SVID, etc.) must be added to the
active channel list separately before they can be accessed. Refer
to the Setup menu section at the end of this chapter for more
information on the Channel menu and List & Labels.
Set the Time
TIME
The current time options might not be available to the basic user,
depending on how they've been set by the master user. (The Time
Configuration menu isn't available in the basic menu).
Go Back
Time Config.
Sleep Timer
...
To set the time, from the Main menu select Time then Time Config. If the
current time has not been set, use the arrow and number buttons on the
remote control to make changes.
00:00
Wake-Up Timer
Schedule
...
...
1. From the Main menu, highlight Time and press OK.
2. Time Config. is highlighted. Press the right arrow to enter the menu.
3. Time is highlighted. To set the time press the right and left arrow
button to add or subtract minutes. Use the number buttons to set the
hour. The OK button changes am and pm.
TIME CONFIG
Go Back
The ClonePRO™
Time
08:25AM
Disabled...
None....
If several TVs need to be programmed with the same menu settings, an
optional ClonePRO remote can be used to copy all of the menu settings
from one TV into other TVs to reduce installation time. Information can
be both downloaded to and uploaded from the ClonePRO using the
DSCI port on the TV’s back panel or using the IR sensor. A ClonePRO
can be obtained from your RCA commercial distributor. Chapter 2 has
information about this remote, see page 20. If you want to set other
menu options before using the ClonePRO, continue on in this chapter.
You can use the ClonePRO at any time.
Set Time Access
Time Offset
Chapter 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Understanding the Menus
This television displays two levels of menus: master and basic.
MAIN MENU - MASTER
Exit
Sound
Picture
Master Menus
The master menus are accessible by pressing MENU on the master remote
(CRK17TD1). This menu shows all menu options. The person who chooses the
settings available to the basic end user is called the “master user.”
Access and Power Options
Parental Control
Time
Setup
Basic Menus
The basic menus are accessible by pressing MENU on a basic remote
(CRK17TC1 or other remote) or the front panel. The choices available on
the basic menus and control panels will vary depending on limits set by the
master user and the input selected. You can turn off the basic menu completely
through the Access & Power Options menu. For more information on the effects
of master user choices on the basic menu and basic user functionality, continue
on in this chapter.
The Master Main menu.
Note: Options set in the master menu are stored in nonvolatile memory. If
any options are changed in the basic menu, and then the TV is turned off,
the TV defaults to the master menu settings once it’s turned back on.
Using Master and Basic Menus
Menus and choice lists use the “point and select” rule to navigate, but control
panels use a variety of methods to adjust features on your TV. The following
pages detail how to use these controls to customize the functions of your TV.
MAIN MENU
Exit
Sound
Picture
Channel Guide
Parental Control
Time
Press MENU on the remote (master remote for master menu; basic remote for
basic menu) or on the front panel (basic menu) to bring up the Main menu.
To select a menu item:
Language & CC
•
•
Navigate with the arrows and then select OK.
Navigate with the arrows and then select with the right arrow button (unless
it's a choice list).
The basic Main menu. The choices
available in this menu change
according to limits set by the master
user.
Exiting a Menu
There are three ways to exit a menu. Note that not all methods work in all menus:
•
•
•
Highlight Exit and press OK.
Press MENU on the remote control.
Press CLEAR, the on-screen displays are cleared from the screen and you return to TV viewing.
Setting Limits in Master Menus
Some screens in the master menus are not available in the basic menus. There also might be some options you want to
make unavailable to the basic user. These next few pages describe these types of menu options. To make all options
unavailable, set the basic menus in the Access & Power Options menu to Disabled. For information on basic menu options,
go to Chapter 3.
10
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Sound Menu
SOUND
Scroll to the feature you want to set. Use the right arrow button to
change the setting.
Go Back
Sound Type
Treble
Stereo...
��
Go Back Takes you to the previous menu.
Bass
Sound Type You'll have different options depending on which jacks
you use and what connections have been made. Choose from Mono,
Stereo, Enhanced, SAP, and LEFT. Stereo splits the incoming stereo audio
signal into left and right channels. Most TV programs and recorded
materials have stereo audio. The word Stereo appears on the TV when
you tune to a program that is broadcast in stereo.
Balance
Initial Volume
Minimum Volume
Maximum Volume
Auto Vol Level
Audio Output
Volume Hold
Treble Increases or decreases the high frequency audio.
Bass Increases or decreases the low frequency audio.
Balance Fades between the left and right speakers.
Fixed...
Initial Volume Sets the TV’s volume to the specified level every time it
is turned on.
Note: When the DSCI (Digital Serial Communications Interface)
port is used to turn the TV on and off, Initial Volume settings are
nonfunctional.
Minimum Volume Re-scales the volume control slider so that the
far left position is always the minimum allowable volume (but not
necessarily the minimum possible volume).
Maximum Volume Re-scales the volume control slider so that the
far right position is always the maximum allowable volume (but not
necessarily the maximum possible volume).
Auto Volume Level Reduces volume blasts during commercial breaks.
Eliminates the need to constantly adjust volume control. Set it On or Off.
The default is Off.
Audio Output Lets you set the audio outputs to fixed or variable
control level. Audio level changes with volume control or when it is
fixed it doesn't change regardless of volume setting. The default is
variable.
Volume Hold Turns the TV’s speakers on and sets the audio outputs
proportional to the current volume setting. When this feature is turned
on, mute and other volume controls are disabled.
Chapter 1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Picture Menu
PICTURE
The Picture menu items allow you to adjust the appearance of on-screen
images for each video input source. Scroll to the feature you want to set.
Use the right arrow button to change the setting.
Go Back
Picture Preset
Auto Color
Color Warmth
Brightness
Color
Bright...
Go Back Takes you to the previous menu.
Normal...
Picture Preset Choose between Soft, Natural, Bright or Personal. The
default setting is Natural.
Auto Color Allows you to set the auto color to On or Off. The default
Contrast
Sharpness
Tint
is Off.
Color Warmth Choose between Cool, Normal or Warm. The default
setting is Normal.
Tilt
Brightness Adjusts the brightness of the picture.
Color Adjusts the richness of the picture.
Contrast Adjusts the contrast of the picture.
Sharpness Adjusts the sharpness of the picture. When the component
inputs are used, this selection is grayed out (disabled).
Tint Adjusts the balance between the red and green levels of the
picture.
Tilt (model J32F635 only) Sets the angle of the TV’s picture. The right
arrow button rotates the picture clockwise. The left arrow button rotates
it counterclockwise. When set by the master user, the setting is used the
next time the TV is turned on.
Access and Power Options Menu
ACCESS AND POWER OPTIONS
Go Back
The Access and Power Options menu allows the master user to specify
which features and functions basic users will be able to access. Scroll
to the feature you want to set. Use the right arrow button to change the
setting.
Remote Config.
Basic Menu Access
TV Power
TV1....
Enabled...
On Always....
Disabled...
Enabled...
Basic...
Go Back Takes you to the previous menu.
Energy Saver
Front Panel
Remote Config. (Configuration) This feature allows the master
user to determine which TVs the remote operates. Choose from TV1,
TV2, TV3, TV1&2, TV1&3, TV2&3, All or Disabled. The default setting is
All. If Disabled is chosen, the TV will not respond to the basic remote,
except when MENU from the master remote has been pressed.
Parental Control
Min Stdby Power
Legacy Mode
Enabled...
Note: Although the TV supports TV3, the master remote cannot
be programmed for it.
Note: The Sleep Timer, Schedule and Energy
Saver settings are unavailable when On
Always has been activated, even if they were
set prior to choosing this option.
Basic Menu Access This setting allows you to determine whether the
TV's basic menus are accessible. Choose Enabled or Disabled. When the
basic menu is disabled, users cannot access menus through the basic
remote or front panel.
TV Power This setting allows you to determine whether the TV can
be turned on or off with the POWER button on the remote or the front
panel. Choose between:
12
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
On Always The TV is always on and cannot be turned off; the Sleep Timer, Schedule and Energy Saver settings are
disabled.
Notes: When On Always is being used, KidPass is unavailable.
When the DSCI (Digital Serial Communications Interface) port is used to turn the TV on and off, the On Always setting is
overridden.
Switched The TV can be turned on or off; Sleep Timer, Schedule and Energy Saver can be enabled. This is the default
setting.
Energy Saver When enabled, this feature turns the TV off after a specified period of inactivity (no remote or front panel
button presses). You can toggle between Disabled, 2-hour, 1-hour, and 30-minute settings. Disabled is the default setting.
If TV Power is set to On Always, Energy Saver settings are ignored. A warning message will be displayed prior to the TV
shutting off.
Front Panel This setting determines whether the front panel buttons are active (able to be used to control the TV) or not.
Parental Controls This feature determines the amount of access basic users have to Parental Controls. Blocking age-
based rating and content themes is described in Chapter 3. Choose between:
Basic&Pwd (Password) Basic users are able to enter the Parental Control menu and change the password. Basic
users can watch blocked programming by entering the system password. This is the default setting.
Basic Basic users are able to enter the Parental Control menu but cannot change the password. Basic users can watch
blocked programming by entering the system password.
NoBasic Parental Control does not appear on the basic Main menu. Basic users can watch blocked programming by
entering the system password.
If Parental Controls is set to NoBasic, Movie Rating Access, TV Rating Access, Unrated Program Block, and Channel Block
will not be available to basic users, regardless of what those items have been set to individually in the Parental Controls
menu.
Min Stdby Power When enabled, keeps power consumption levels compliant with ENERGY STAR® guidelines. The TV is
shipped with this enabled.
Legacy Mode When turned On, allows the TV to work with earlier DSCI versions. Thus making the set usable with older
systems. Off is the default setting.
Note: When Remote Config. and Front Panel are set to Disabled, the MENU button on the master remote turns on the
TV.
Chapter 1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Parental Control
PARENTAL CONTROL
This menu shows all Parental Control menu options. As the master user,
you choose which options are available to the basic end user. Scroll to
the feature you want to set. Use the right arrow button to change the
setting.
Go Back
USA V-Chip
...
...
Canada V-Chip
Unrated/Exempt Prg.
KidPass
Go Back Takes you to the previous menu.
...
USA V-Chip Displays settings for the US version of V-Chip. If you live
Front Panel Lock
within the United States, choose this option.
Lock Par. Controls
Par. Control Access
...
...
Canada V-Chip Displays settings for the Canadian version of V-Chip.
If you live in Canada, choose this option.
Unrated/Exempt Prg. (Program) This setting allows the master user
to determine whether they will allow unrated/exempt programs to be
shown. Choose Unlocked for all unrated programs to be shown. Choose
Locked and all unrated programs are not available. For more information,
go to page 29.
Note: The master user is always able to enter
Parental Controls and change the password.
KidPass The KidPass feature allows parents to set a certain amount
of time every day of the week that a child can watch TV. For more
information on this feature, go to page 30.
Note: When TV Power is set to On Always, KidPass settings are
nonfunctional. The time must be set for KidPass to function.
Front Panel Lock This setting allows you to disable (lock) the TV's
front panel buttons and may be used as a Parental Control method. When
doing so, remove access to any remote capable of operating the TV. The
remote still tunes in the channels.
Lock Par. (Parental) Controls Puts into effect settings made in the
Parental Control menu. A password is required.
Par. (Parental) Control Access This feature allows you to choose
which Parental Control menu item is accessible through the basic menus.
If basic users are able to access the Parental Control menu, the master
user can still set limited access within the menu through the Par. Control
Access menu. The setting toggles between Basic and No Basic. The
options within the access menu are: U.S. Movie Rating Access, US TV
Rating Access, CA Eng. Rating, CA French Rating, Unrated/Excempt, and
KidPass.
14
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Time Menu
TIME
This control panel lets you control several time-related functions. Scroll
to the feature you want to set. Use the right arrow button to change the
setting.
Go Back
Time Config.
Sleep Timer
...
00:00
Go Back Takes you to the previous menu.
Wake-Up Timer
Schedule
...
...
Time Config. Takes you to the Time Configuration menu.
Go Back Takes you to the previous menu.
Time Displays the current time if the master user has set the time. If
allowed by the master user, the basic user can set the time. Press OK
to toggle between am and pm.
Set Time Access The master user selects who is able to set and
change the current time:
TIME CONFIG
Go Back
Basic Basic users are able access the current time
information and can make changes.
Time
08:25AM
Disabled...
None....
Disabled If the master user has set the time, the time
information is available but cannot be changed.
Set Time Access
Time Offset
Automatic Basic users are able to access the current time
information but cannot make changes. With this option, if the
master user doesn't set the time, the TV software will try to
acquire time information from broadcasts that provide it.
Time Offset Sets an offset (from +12 to -12 hours) from Universal
Time (UCT). The setting is in increments of 30 minutes. If you enter
the time manually, this option appears gray (disabled). Common US
offsets from UCT are:
Eastern
Central
-5:00
-6:00
Mountain -7:00
Pacific
Alaska
Hawaii
-8:00
-9:00
-10:00
Sleep Timer Lets you set the TV to turn off after a given time. Press the
right arrow to add 15 minutes to the clock (up to four hours).
Wake-Up Timer Lets the master user set availability to this timer On or
Off.
Note: When the ClonePRO remote is used via the TV’s DSCI (Digital
Serial Communications Interface) port to turn the TV on and off,
Sleep Timer and Wake-Up Timer settings are nonfunctional.
Schedule Lets you set the TV to turn on and off at specified times on a
specified channel--one time or daily.
Chapter 1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections & Setup
Setup Menu
SETUP
Use this menu for choosing options to get you started watching TV. Scroll
to the feature you want to set. Use the right arrow button to change the
setting.
Go Back
Language
English...
Signal Type
Cable...
Go Back Takes you to the previous menu.
Weak Signal Disp.
Auto Ch. Search
List & Labels
Channel Selection
Channel Guide
Auto Tuning
None...
Language Lets you select your preferred language for the menus.
...
...
...
...
...
...
Signal Type Displays a choice list to choose the signal your TV is
receiving. Choose Cable if you are currently using cable or a cable box for
TV signals. Choose VHF/UHF if you are currently using an off-air antenna
for TV signals.
Closed Caption
Weak Signal Disp. (Display) When the signal is weak or there isn't a
signal, allows you to select between these options:
Mute & Blank Displays a gray screen with the message “Unusable
Signal” with the sound muted until a usable signal is found.
None No message is displayed.
Auto Channel Search Allows the TV to search for available channels to
be saved into memory.
List & Labels Lets you edit the channels in the list or choose labels for
each channel. To delete a channel from the channel list, highlight Channel
and use the left or right arrow to select the channel. Then highlight In list
and press the OK button. The box should no longer display a check mark.
To add a label to a channel, select the channel in the Channel option. Press
the down arrow to highlight Label. Press the right arrow to highlight the
first space. Use the up or down arrow to ascend or descend through the
characters. Continue to press the right arrow to highlight the space and the
up or down arrow to add a character. Press OK when you’re done adding a
label.
Channel Selection Allows the master user to set the initial channel and
to select which of the three channel lists will be active (accessible to the
basic user). If no initial channel is selected, the TV tunes to the last channel
when turned on. If Hold is selected, the user won't be able to select any
channel other than the current channel.
Channel Guide Displays the list of channels and their labels (if labelled)
in the active channel list.
Auto Tuning When a universal remote is used, displays a choice list to
set up the TV to automatically tune to the correct Video Input Channel.
Allows the basic user to press a component button (VCR, DVD etc.) to
select a specific channel or input.
Closed Caption Lets you choose the way closed captioning information is
shown on the screen. The options are:
Off No captioning information displayed. This is the default option.
On Captioning information shown always, when available.
Muted=On Captioning information is shown when the MUTE button
is pressed.
16
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Using the Remote Control
Types of Remote Controls
All of the remote controls mentioned here, in addition to other remotes and accessories, are
available from your RCA distributor. The accessory page at the back of this user's guide lists
items. Descriptions of the remote buttons and how they work are on the next pages. Except
as otherwise specified, the master remote is the remote described throughout the manual for
operating the TV and setting up the TV’s features.
CCPOWER
SLEEP
CHAN
SYSTEM
VOL
GO
MUTE BACK
INFO
GUIDE
Master Remotes
OK
The master remote control (CRK17TD1) accesses all of the TV’s menus. It is used to
customize the TV’s functionality for specific users or specific situations.
MENU
CLEAR
3
6
9
1
2
5
8
0
Basic Remotes
4
7
The basic remote control (CRK17TC1) is used by the viewer for basic operating functions.
It is designed so that the viewer cannot alter certain master remote-specified features. The
Sleep, Closed Captioning, and Channel Guide features can be accessed directly with remote
buttons.
INPUT
RESET
M A S T E R
ClonePRO
The ClonePRO has main operating buttons that function the same as the master remote.
Master Remote CRK17TD1
Basic Remote Buttons (CRK17TC1 & CRK17TD1)
Arrow Buttons and OK Use the arrow buttons to highlight your choices and navigate the
menu system. Use the OK button to select your choice.
CC (Closed Captioning) Displays the Closed-Caption Display. Subsequent presses change
the display mode.
CC
POWER SLEEP
SYSTEM
CHAN (Channel up or down) Scans up and down through channels in the TV’s memory.
CLEAR Clears menus and displays from the screen.
VOL
CHAN
GO
MUTE BACK
GO BACK Tunes the TV to the last selected channel or video input channel.
GUIDE Displays the Channel Guide (when not in the menu system).
INFO Displays channel information. Press again to clear channel information.
INFO
GUIDE
OK
MENU
CLEAR
INPUT Switches between TV (channels 01-125) and other available inputs. See description
3
6
9
1
2
5
8
0
later in this chapter for more details.
4
7
MENU Brings basic menus to the screen and moves from menu to menu. Also, clears the
current menu from the screen.
SKIP
INPUT
MUTE Lowers the volume to its minimum level. Press again to restore volume.
Number Buttons (0-9) Selects an available channel number. Two digits must be pressed for
each channel. Press 0 then 6 for channel 6. For three-digit channel numbers, press and hold
1 until "1--" appears on the screen. Then press the other two digits.
POWER Turns the TV on or off.
Basic Remote CRK17TC1
Continues on next page...
Chapter 2
17
Graphics contained within this publication are for representation only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
SKIP (Commercial Skip- CRK17TC1) Press once before changing the channels and the TV waits
30 seconds before returning to the original channel. Each subsequent press adds 30 seconds to the
skip time. Press CLEAR to cancel.
SLEEP Displays the Sleep Timer control panel, which allows the user to set a time for the TV to
turn itself off.
SYSTEM Allows the remote to change between TV1 and TV2 mode. It also allows access to
system-defined functionality, when available. See the description later in this chapter for more
details.
VOL (Volume up or down) Decrease or increase the TV's volume (unless Volume Hold is on) and
displays the Volume Control slider. Go to Chapter 1 for more information on Volume Hold.
CCPOWER
SLEEP
CHAN
Additional Remote Buttons (CRK17TD1)
MENU (MASTER) Brings up the master menu screen. This is different from the
SYSTEM
VOL
GO
MUTE BACK
basic user menu screen.
RESET (MASTER) Returns the picture to the original settings and displays the
Picture Presets choice list.
INFO
GUIDE
OK
MENU
button
MENU
CLEAR
3
6
9
1
2
5
8
0
4
7
INPUT
RESET
RESET
button
M A S T E R
Master Remote CRK17TD1
18
Chapter 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Using the INPUT Button
In addition to a cable or antenna signal, you might have VCR, DVD etc. or
other signals coming in to your TV (not all inputs are available on all models).
Use the INPUT button to select the desired signal source.
CCPOWER
SLEEP
CHAN
SYSTEM
SYSTEM
button
1. Make sure that the component you want to view is turned on.
2. Press INPUT until you have selected the desired input source.
VOL
GO
MUTE BACK
INFO
GUIDE
Inputs and On-Screen Displays
OK
The Status Display shows which input signal(s) is selected. The following table
shows which display term usually corresponds with which input.
Input Signal
TV Display
(channel digit)
VID1
MENU
CLEAR
1 and 2
buttons
3
6
9
1
2
5
8
0
ANTENNA/CABLE jack
Rear A/V jacks
Front Jacks
4
7
FRNT
INPUT
RESET
INPUT
button
Using the SYSTEM Button
When the television is connected to an interactive system or similar device,
the SYSTEM button allows you to access system programming or other special
functionality through the DSCI jack.
M A S T E R
On a master or basic remote, the SYSTEM button can also allow independent
remote control of two TVs. Once you have specified TV1 or TV2 status for the
TVs, see the Access and Power Options menu on page 12. Follow these steps
to tell the remote which TV you want to operate:
Note: Although the TV supports TV3, the
master remote cannot be programmed
for it.
1. On the remote control, simultaneously press and hold the SYSTEM button
and 1 (for TV1) or 2 (for TV2).
2. After several seconds, release the buttons. The specified TV will respond to
that remote.
3. To control the other TV, simply repeat the process using the other
(1 or 2) button.
Chapter 2
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
ClonePRO™ Remote Buttons
The ClonePRO can be used as a master remote. First, press ON to turn the remote on. Some of the buttons only apply when
using the ClonePRO to download or upload information to or from a TV. Those buttons are described in Chapter 5.
Note: After 30 seconds of inactivity the remote will turn itself off.
RESET Returns the picture to the
original settings and displays the
Picture Presets choice list.
INFO Displays channel
information.
Arrow buttons (up, down, left,
right) Use to move through the
on-screen menus. When a menu
isn’t displayed, the up and down
arrows scan the channel list. The
left and right arrows decrease or
increase the TV’s volume, unless
Volume Hold is enabled. Chapter
1 has more information on Volume
Hold.
OK Press to select a menu item
that is highlighted.
CLEAR Removes any menu or
display from the screen and returns
you to TV viewing.
MENU Displays the master main
menu.
20
Chapter 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Using the Menu System
The Basic Menu System
MAIN MENU
Exit
The basic menus are accessible through basic remote controls and
the front panel. Which menu items are available will depend on the
restrictions set by the master user and the active input. For instance, if
Basic Menu Access has been set to Disabled in the Access and Power
Options menu, the basic menus and many features will not be available.
Also, except for some Parental Controls settings, many of the changes
made in the basic menu will revert back to their master menu settings
the next time the TV is turned on. Many of the basic menu items function
exactly the same as their master menu counterparts. (See Chapter 1 for
more details on the master menus.)
Sound
Picture
Channel Guide
Parental Control
Time
Language & CC
Sound Menu
Go Back Takes you to the previous menu.
SOUND
Sound Type Choose Stereo, Enhanced, SAP or Mono. If you connect
Go Back
to VID1 or the front jacks, choose from Stereo or Left. Stereo splits
Sound Type
Stereo...
the incoming stereo audio signal into left and right channels. Most TV
programs and recorded materials have stereo audio. Stereo or Mono
is displayed in the Channel banner when chosen. SAP (Second Audio
Program) plays the program's audio in a second language, if one is
available. This selection is displayed in the Channel banner when
chosen.
Picture Menu
The basic Picture menu items allow you to adjust the appearance of
PICTURE
Go Back
on-screen images.
Picture Preset
Bright...
Go Back Takes you to the previous menu.
Picture Preset Choose between Soft, Natural, Bright or Personal. The
default setting is Natural.
Channel Guide Menu
CHANNEL GUIDE
The basic Channel Guide menu is the same as the master Channel Guide
menu. It will only display the channels chosen by the master user.
CH 001
CH 002
CH 003
CH 004
CH 005
CH 006
CH 007
CH 008
CH 009
CH 010
Select: OK
Page +: >
Page -: <
Press MENU to exit.
Chapter 3
21
Graphics contained within this publication are for representation only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu System
Parental Control Menu
PARENTAL CONTROL
Go Back
The basic Parental Control menu will depend on the options set by the
master user. If the master user chooses Allow Basic on menu items, then
all options are available. To set movie and TV ratings, content themes,
etc., go to Chapter 4.
USA V-Chip
Canada V-Chip
Unrated/Exempt Prg.
KidPass
Go Back Takes you to the previous menu.
USA V-Chip Displays settings for the US version of V-Chip. If you live
within the United States, choose this option.
Canada V-Chip Displays settings for the Canadian version of V-Chip.
Lock Par. Controls
If you live in Canada, choose this option.
Unrated/Exempt Prg. (Program) This setting allows the master user
to determine whether they will allow unrated/exempt programs to be
shown. Unlocked- All unrated programs are shown. Locked- All unrated
programs are not available. Page 29 has more information.
KidPass The KidPass feature allows parents to set a certain amount of
time every day of the week that a child can watch TV.
Note: The time must be set for KidPass to function.
Lock Par. (Parental) Controls Puts into effect settings made in the
Parental Control menu. A password is required.
Note: Parental Control Access is the master menu that controls
which menus are available to the basic end user. Go to Chapter 1
for more details.
Time Menu
TIME
The functions of the basic Time menu will depend on the options set by
the Master user.
Go Back
Go Back Takes you to the previous menu.
Time
08:25AM
00:45
Sleep Timer
Wake-Up Timer
Time Displays the current time if the master user has set the time.
Sleep Timer Lets you select the amount of time (in 15 minute
increments) you want to give the TV before it shuts itself off (up to four
hours). A message is displayed as a warning before the TV turns off.
Select 00:00 to stop this function. This feature won't work if TV Power in
the master menu is set to On Always. The default setting is 00:00.
Wake-Up Timer Displays a menu that lets you enter the time and
channel you want your TV to turn to when it turns on.
The Sleep Timer and Energy Saver settings
are unavailable when On Always has been
activated, even if they were set prior to
choosing this option.
Note: The Time Configuration menu allows
the master user to make changes to the
master menu regarding time. Go to Chapter 1
for more details.
22
Chapter 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu System
Language & CC Menu
LANGUAGE & CC
Go Back Takes you to the previous menu.
Go Back
Language Displays your preferred language for the menus. Select
English, Français (French) or Español (Spanish).
Language
CC Display
CC Mode
English...
On...
CC1...
CC Display Use the CC button on the remote to choose whether
closed captioning information is shown on the screen.
CC Mode When CC Display is turned on, displays the CC mode: CC1,
CC2, CC3, CC4, T1, T2, T3 or T4.
The TV can be "Decommercialized"
If you no longer want your TV to function as a commercial one, the steps below describe how
to make it a non-commercial TV. Many features and options found in non-commercial TVs are
included for your use.
• Make sure the TV is off.
• Press VOL- on the front of the TV and MENU on the remote for a few seconds
simultaneously.
• The TV will turn on and activate the decommercialization sequence.
Note: In the case of inadvertent decommercialization, the user can reverse the TV to a
commercial set by using the same button combination above. The decommercialized TV will
turn on and reset to a commercial set.
When using the ClonePro remote, it has buttons to decommercialize and commercialize the
TV. Go to page 31 for more information.
Chapter 3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Using the TV's Features
Channel Banner
There are several items that might appear on-screen when you press the
TV or INFO button on the remote. This display is called the Channel
Banner. The following list describes the items on the Channel Banner
screen (left to right and top to bottom).
SAP
Displayed when the current channel is broadcasting SAP
(Second Audio Program) information.
KidPass: 2:24
Skip: 0:30
CC
07:18am
SAP
Stereo
06 ABCDEF
Displayed when V-Chip has been activated.
X
KidPass:2:24
CC
Displayed when KidPass is set and the length of time
remaining.
Displayed when Closed Captioning is available on the
current channel.
Stereo or Mono Stereo is displayed when the current channel is
broadcasting in stereo. Mono is displayed when the
current channel is broadcasting in mono.
Skip:0:30
Corresponds to the SKIP button. Shows the amount of
time left before the TV switches back to the previous
channel.
07:18 am
Displays the current time.
06 ABCDEF
Displays the current channel and label assigned to the
channel.
Displayed when you mute the sound.
Parental Controls and V-Chip
The choices in the USA V-CHIP menu involve software inside your TV (referred to as V-Chip) which allows you to block TV
programs and movies based on violence, sex, or other content you may believe children should not view.
Once you block programs, you can unblock programs by entering a password.
By default, the software inside your TV is turned “off.”
How V-Chip Works
V-Chip reads the program’s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence (V), Adult Language (L),
etc.)]. If you have blocked the rating and/or content themes that the program contains, you will receive the message, "This
channel has not been approved for viewing".Change channel or press OK to enter password and temporarily deactivate the
Parental Control.
Broadcasters are not required to provide content themes, so programs received with no content themes will only be
blocked if you block their age-based rating. You can also block out programs that have been given a rating of Not Rated,
and programs that are considered unrated. The TV age-based ratings and content themes you can block follow:
24
Chapter 4
Graphics contained within this publication are for representation only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
USA V-Chip Rating System
TV-MA (Mature Audience Only) Specifically designed to be viewed by adults and may be unsuitable for children under 17. It
contains one or more of the following content themes: crude indecent language (L), explicit sexual activity (S), or graphic
violence (V).
TV-14 (Parents Strongly Cautioned) Contains some material that many parents would find unsuitable for children under 14.
Parents are strongly urged to exercise greater care in monitoring this program and are cautioned against letting children
under the age of 14 watch unattended. This program contains one or more of the following content themes: intensely
suggestive dialogue (D), strong coarse language (L), intense sexual situations (S), or intense violence (V).
TV-PG (Parental Guidance Suggested) Contains material that parents may find unsuitable for younger children. Many parents
may want to watch it with their younger children. The program contains one or more of the following content themes:
some suggestive dialogue (D), infrequent coarse language (L), some sexual situations (S), or moderate violence (V).
TV-G (General Audience) Most parents would find this program suitable for all ages. It contains little or no sexual dialogue
(D) or situations (S), no strong language (L), and little or no violence (V).
TV-Y7 (Directed to Children 7 years and older) Designed for children ages 7 and above. It may be more appropriate for
children who have acquired the developmental skills needed to distinguish between make-believe and reality. Themes and
elements in this program may include mild fantasy violence (FV) or comedic violence, or may frighten children under the
age of 7.
TV-Y (All Children) Themes and elements in this program are designed for a young audience, including children from ages
2-6. It is not expected to frighten younger children.
Canadian English V-Chip Rating System
18+ (Adults) Programming intended for adults 18 and older. It may contain elements of violence, language, and sexual
content which could make it unsuitable for viewers under 18. Violence Guidelines: May contain violence integral to the
development of the plot, character or theme, intended for adult audiences. Other Content Guidelines: May contain graphic
language and explicit portrayals of nudity and/or sex.
14+ (Viewers 14 and over) Programming contains themes or content which may not be suitable for viewers under the age
of 14. Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens. Violence
Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a realistic fashion.
Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent use of profanity.
PG (Parental Guidance) Programming intended for a general audience but which may not be suitable for younger children
(under the age of 8). Parents may consider some content inappropriate for unsupervised viewing by children aged 8-13.
Violence Guidelines: Depictions of conflict and/or aggression will be limited and moderate; may include physical, fantasy,
or supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or mildly suggestive language.
Could also contain brief scenes of nudity.
G (General Audience) Programming considered acceptable for all ages groups. While not designed specifically for children,
it is understood younger viewers may be part of the audience. Violence Guidelines: Will contain very little violence, either
physical or verbal or emotional. Will be sensitive to themes which could frighten a younger child, will not depict realistic
scenes of violence which minimize or gloss over the effects of violent acts. Other Content Guidelines: There may be some
inoffensive slang, no profanity and no nudity.
C8+ (Children 8 and Older) Programming generally considered acceptable for children 8 years and over to watch on their
own. Violence Guidelines: Violence will not be portrayed as the preferred, acceptable, or only way to resolve conflict or
encourage children to imitate dangerous acts which they may see on television. Any realistic depictions of violence will be
infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content Guidelines: There will be
no profanity, nudity or sexual content.
Continues on next page...
Chapter 4
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
C (Children) Programming intended for children under age 8. Violence Guidelines: Careful attention is paid to themes
which could threaten children’s sense of security and well being. There will be no realistic scenes of violence. Depictions of
aggressive behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature.
Other Content Guidelines: There will be no offensive language, nudity or sexual content.
Canadian French V-Chip Rating System
18+ (Adults) Programming is for adults only. This program contains sustained violence or extremely violent scenes.
16+ (Viewers 16 and over) Programming is not suitable for those under age 16. This program contains frequent scenes of
violence or intensely violent scenes.
13+ (Viewers 13 and over) Programming may not be suitable for children under the age of 13. This program either contains
several violent scenes or one or more scenes that are violent enough to affect them. Viewing in the company of an adult is
therefore strongly recommended for children under the age of 13.
8+ (Viewers 8 and over) Not recommended for young children. This program is suitable for most audiences, but it contains
mild or occasional violence that could upset young children. Viewing in the company of an adult is therefore recommended
for young children (under the age of 8) who do not distinguish between reality and imagination.
G (General Audience) This program is suitable for audiences of all ages. It contains no violence, or any violence that it does
contain is either minimal or is presented in a humorous manner, as a caricature, or in an unrealistic way.
USA V-Chip TV Rating Limit
PARENTAL CONTROL
The V-Chip TV Rating Limit lets you decide which TV programs can and
cannot be viewed.
Go Back
USA V-Chip
To set TV programming limits:
Canada V-Chip
USA V-CHIP
1. Choose Parental Control from the Main menu (the PASSWORD screen
appears the first time you enter the Parental Control menu). Create
your password using the number buttons on the remote.
Go Back
Movie Ratings
2. Highlight and select USA V-Chip. Then select TV Ratings.
3. Once you get to the TV RATING LIMIT screen, use the arrow buttons
and OK on your remote to change the status of a TV program rating or
content theme from View to Block.
TV RATING LIMIT
Go Back
The following sections give you more details about how to change the
status of TV program limits.
Status
View
D
L
S
V
FV
TV-MA
TV-14
TV-PG
G
V
V
V
V
V
V
V
V
V
View
View
View
B
B
Note: If you forget your password you can reset it. Make sure the TV
is off. Simultaneously press and hold VOL- on the TV’s front panel
and CLEAR on the remote for approximately 5 seconds. Enter a new
password the next time you access the PARENTAL CONTROL menu.
TV-17
TV-Y
View
View
V
Press OK to View/Block prog.
with this rating.
26
Chapter 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
The V-Chip Rating Screen
The following is an example of where items are located within the TV RATING LIMIT screen.
Rating Status Field
Lets you select whether the status of the age-based rating limit to the left is View or
Block.
Content Themes
TV RATING LIMIT
Lists the content themes you can block or
view.
Go Back
Status
View
View
View
View
View
View
D
L
S
V
V
V
V
V
V
V
FV
V
Rating Field
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
V
V
V
Lets you select from
a list of age-based
ratings you can block
or view.
Content Status Fields
B
B
Lets you select which content
themes to view for the selected
rating, and whether the
status of the content theme is
currently View (V) or Block (B).
Press OK to view/block
prog. with this rating.
Rating Settings Area
Lets you see the current block/view state of age-based
ratings and associated content.
Blocking Age-Based Ratings
You can automatically block all program ratings above a specified age-
Hierarchy of Age-Based Ratings
TV-MA
TV-14
TV-PG
TV-G
Mature Audience Only
Parents Strongly Cautioned
Parental Guidance Suggested
General Audience
based rating level.
To block programs with higher ratings:
1. Press the up or down arrow button to scroll to the rating
corresponding with the lowest rating you do not want the child to
watch.
2. Press the OK button to toggle between View and Block. The status
for the rating listed to the left and all higher ratings automatically
changes to Block.
TV-Y7
TV-Y
Directed to Children 7 years and older
All Children
3. Press the up or down arrow button to highlight Go back and press
OK.
4. Turn on V-Chip active in the PARENTAL CONTROL menu (box has
check mark) for rating limits to take effect.
Viewing Age-Based Ratings
After you block age-based ratings, you can change some of the ratings back to View.
1. Press the up or down arrow button to select the rating with a status of Block.
2. Press OK to select View.
Chapter 4
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
Blocking Specific Content Themes
Content Themes
Sexually explicit dialogue
Adult language
You can block programs based on their content. (Content is represented
by the D, L, S, V and FV on your screen.) When you block a content
theme for a particular rating, you automatically block that content theme
for higher rated programs as well.
D
L
S
Sexual situations
Violence
To block program content:
V
1. Determine the content themes you want to block.
FV
Fantasy Violence
2. Press the down arrow button to scroll to the rating whose content
theme you want to change.
3. Press the right arrow button to move the highlight to a particular
content theme status.
4. Press the OK button to change its status to B. (In the example to
the left, you block the language (L) corresponding with TV-14. The
language for TV-MA is blocked as well).
Notes: Broadcasters are not required to provide content themes or
age-based ratings.
You must remember to activate Parental Controls for rating limits
to take effect.
Viewing Specific Content Themes
If you block specific content themes, you have the option of going back and changing some of the content themes back to
(V) View:
1. Determine the content themes you want to change to (V) View.
2. Press the down arrow button to scroll to the rating whose content theme you want to change, such as B under language
(L) corresponding with TV-14.
3. Press the right arrow button to move the highlight to a particular content theme status.
4. Press the OK button to change the status back to V. Your child would then be able to watch programs with the TV-14
adult language content, but not programs with TV-MA language content.
Note: Only the content theme status corresponding to TV-14 (L) language changes to (V) View. Higher rated content
themes, such as that for TV-MA language, do not change.
28
Chapter 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
Blocking Canadian V-Chip Ratings
ENGLISH RATINGS
If you receive Canadian programs you can block Canadian English and
French V-Chip by ratings only. When you block a particular rating, you
automatically block the higher rated programs as well.
Go Back
18+
14+
PG
G
C8+
C
To block Canadian English and French program ratings:
1. Select Canada V-Chip from the PARENTAL CONTROL menu.
2. Highlight English Ratings or French Ratings and press OK.
3. Determine the rating you want to block.
Press OK to view/block
programs intended for
children over the age of 8.
4. Press the down arrow button to scroll to the rating you want to
change.
FRENCH RATINGS
5. Press the OK button to change its status to block (the lock icon
appears and all ratings above the one you selected change to lock).
Go Back
18+
16+
13+
8+
G
Press OK to view/block
programs intended for
children over the age of 8.
V-Chip Movie Rating Limit
Set movie rating limits by blocking movies rated above a specified level.
To access the Movie Rating Limit menu:
1. Press MENU on the remote control (the MAIN MENU appears).
2. Select Parental Control.
3. Select USA V-Chip.
4. Select Movie Ratings.
Blocking Movie Ratings
Once you are in the Movie Rating Limit menu, follow the same steps described for blocking Canadian V-Chip Ratings.
V-Chip Exempt Program Block
The Exempt Prgms. option lets you decide if programs that the V-Chip recognizes as unrated can be viewed. Unrated
TV programs may include news, sports, political, religious, local and weather programs, emergency bulletins, public
announcements, and programs without ratings. The Exempt option applies to both USA and Canadian unrated programs
and Canadian programs rated E.
Unlocked All unrated programs are available.
Locked All unrated programs are not available.
Press the down arrow to highlight Exempt Prgms. Then press the right arrow to toggle between the lock and unlock icon.
Chapter 4
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Features
KidPass
The KidPass feature allows parents to set a certain amount of time every day of the week that a child can watch TV. To set
KidPass:
1. Select Parental Control from the main menu.
2. Select KidPass (the KIDPASS menu appears with Current Day highlighted).
Note: If you can’t select KidPass, you need to set the time. Highlight Go Back and press OK. Select Time and press OK.
Enter the Time Config. menu. Set the time using the arrow and number buttons.
3. Press the right arrow to select the current day.
4. Press the down arrow button to choose the day of the week.
5. After you’ve chosen the day of the week, press the right arrow to select the amount of time: Free and 00:30 up to 16:00
(30 minute increments).
6. When you’re done setting KidPass, select Go Back.
7. Go to Lock Par. Controls and activate KidPass by entering the password.
When the time has expired, the TV shuts off. If you turn on the TV the same day it shut off, the password screen appears
(enter the password used for Parental Control).
Notes: If control has been turned off in the master menu (Disallow Basic) this feature will not be available to other
users.
You can change settings in the Parental Control menu only when Lock Par. Controls is in the unlocked position.
If you forget your password you can reset it. Make sure the TV is off. Simultaneously press and hold VOL- on the TV’s
front panel and CLEAR on the remote for approximately 5 seconds. Enter a new password next time you access the
PARENTAL CONTROL menu.
Front Panel Lock
Selecting this option lets you lock (disable) or unlock (enable) the TV’s front panel. The remote still tunes to any channel.
When using this as a Parental Control method, remove access to any remote that is capable of operating the television.
1. From the PARENTAL CONTROL menu, press the up or down arrow to highlight Front Panel Lock.
2. Press the right or left arrow to turn on (lock is closed) or off (lock is open) front panel lock.
Create Password
Selecting this option lets you create a new password. Enter a new password from the Passwd. menu in the Lock Par.
(Parental) Cont. (Control) menu, this is the password you use until you change it.
30
Chapter 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Chapter 5: Other Information
Using the ClonePRO™
Modes of operation
The ClonePRO operates from one of two modes:
DSCI Connect a DSCI cable to the ClonePRO and to the TV’s DSCI port
on the back panel.
IR (Infrared) This operation is wireless. Press ON to begin using the
remote in IR mode.
The corresponding “ready” light indicates the mode of operation, and the
corresponding “busy” light indicates activity in this mode.
Buttons with black labels function similarly in both modes, while green labels
operate DSCI mode and red labels operate IR mode.
DSCI mode
The ClonePRO enters this mode when it is connected to the TV’s Digital Serial
Communications Interface port via a cable (included).
• Any standard (no-flip, 1-to-1) 8-conductor computer-networking cable
may be used.
• No battery is required in this mode.
• If the unit is already in IR mode, press OFF to speed the transition to
DSCI mode.
DSCI (green) buttons
Comm Restores the TV to normal commercial operation, essentially undoing the effect of the Legacy and Decom buttons.
Decom “Decommercializes” the TV to facilitate aftermarket resale.
[Factory] Press and hold the RESET button for several seconds to re-initialize the TV, reverting all settings to factory defaults.
Note: Pressing FACTORY overwrites any settings already in the TV.
LEARN Begins the process of learning the settings from a TV that has been setup as desired.
Note: Pressing LEARN overwrites any settings already in the ClonePRO.
Legacy Places the TV in a mode in which it emulates the behavior of older models. This is a required part of the
configuration for some applications.
POWER Turns on the TV. It is recommended, though not required, when in DSCI mode to view on-screen displays.
[Status]: Press and hold the INFO button for several seconds to display settings stored in the ClonePRO and the TV. For example:
Mem: CB:36 TV:36
This tells you the ClonePRO and the TV have 36 pages of information stored in memory.
Continues on next page...
Chapter 5
31
Graphics contained within this publication are for representation only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Across the screen are red dashes. Press any button on the remote control you are using. Red pulses should appear, telling
you the TV is recognizing the remote and is able to send out that information. If red pulses don’t appear, contact your RCA
distributor.
TEACH: This begins the process of teaching the settings stored in the ClonePRO to the TV to which it is connected.
Note: Pressing TEACH overwrites any settings already in the TV.
After successful teaching, the TV will turn off and reboot.
If the memory-image stored in the clone-box is not valid for the TV, an on-screen message will advise of the conflicting
memory-sizes.
IR mode
The ClonePRO enters the IR mode when any button on the bottom row of the keypad is pressed (without connection to a
TV DSCI port). A standard 9V battery (accessed via a small rear panel) is required to enable this mode.
Notes: Like any IR (infrared) remote control, the ClonePRO requires a reasonable line of sight between it and the TV
for proper signaling. Obstructions, long distances, sharp angles and certain specialty lighting can reduce the effective
range.
If the “IR ready” light stays on longer than 1 minute by itself, temporarily remove the battery to reset it.
Remove the battery prior to long-term storage.
IR (red) Buttons
Note: You must press the ON button for the IR buttons to operate.
Master+ & Master- The Master- button disables access to the TV’s master menus via the master remote. (Some third-party
devices, attached to the TV’s DSCI port as part of a larger system, may disable access to master menus even after they are
disconnected.) To enable the master menus, press Master+.
OFF Turns the TV off, and turns the ClonePRO off.
ON Turns the TV on, and turns on the ClonePRO IR mode, ready for subsequent buttons. Note that the unit will
automatically turn itself off 30 seconds after the last button has been pressed to extend battery-life.
TEACH Begins teaching the settings stored in the ClonePRO to the TV, effectively “Cloning” the initially configured TV.
May be made more reliable for older models by first filling the memory of the example TV with channel-labels on unused
channels.
After an IRTEACH, older-model TVs do not need to reboot.
Note: Pressing TEACH overwrites any settings already in the TV.
•
•
•
A TV must be turned on before being taught in IR mode.
After successful teaching, the TV turns off and turns on with the new settings.
If the TV displays the message Cloning Timeout or Cloning Aborted, press TEACH again to retry, experimenting with
the ClonePRO at different distances and angles from the TV.
•
If no valid settings have been stored via a DSCI LEARN, the IR ready light will come on but nothing will appear on
the TV screen.
Note: The ClonePRO cannot be used to cross clone (to copy the memory of older models into newer models, or vice
versa), because the two have completely different memory-maps, memory-sizes, features and settings.
[Config]: Pressing and holding this button in IR mode toggles the “decommercialization” and aftermarket resale of older-
model televisions. Note that this is not reversible after turning-off older-model TVs.
32
Chapter 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Cloning a TV
Use the ClonePRO or a master remote to complete any necessary setup steps to the TV, such
as Auto Channel Search, changing Access & Power options, etc. Go to Chapter 1 for more
information on setting up the TV. When you have finished setting up the TV, you can use it as
your example TV.
1. Connect the ClonePRO to the example TV’s DSCI port.
2. It is recommended, though not required, to turn on the TV. Press the POWER button.
3. Press the LEARN button to begin the cloning process. When it is complete, Cloning
Complete is displayed on-screen.
4. Take the ClonePRO to each subsequent TV and then (in either DSCI or IR mode) TEACH
each TV, monitoring the process on-screen.
The settings learned by the ClonePRO remain indefinitely, ready to TEACH the next TV until
overwritten by a new LEARN operation.
General troubleshooting
Problems with the DSCI mode
• Make sure the TV is plugged into a live electrical outlet.
• Make sure the ClonePRO is plugged into the TV’s DSCI port.
• The connecting cable should have at least 6 wires, mapping 1-to-1 (not flipped).
ClonePro remote isn't working
• Check the battery. Place a new 9V battery in the unit if the battery is old.
• Make sure the ClonePRO is pointed at the TV with a clear line of sight.
• If you are trying to TEACH, make sure there is a valid memory stored in the ClonePRO
(Check by going into DSCI-mode [Status].)
Chapter 5
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Troubleshooting
Most problems you encounter with your TV can be corrected by consulting the Troubleshooting list that follows.
Note: If you prefer, we can provide you with the name of an Authorized Service Representative who will visit your
location for a fee to install your electronic entertainment system and to instruct you in its operation. For details about
this service, call 1-888-206-3359.
To contact the nearest RCA Service Center call 1-800-880-5966.
TV Problems
TV won’t turn on
•
•
•
•
Press the TV button.
Make sure the TV is plugged in.
Check the wall receptacle (or extension cord) to make sure it is “live” by plugging in something else.
Something might be wrong with your remote control. Press the POWER button on the front of the TV. If the TV turns on, check
the remote control solutions on the next page.
•
The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting Front
Panel in the Access & Power Options menu and choosing Enabled.
Controls don’t work
•
The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting Front
Panel in the Access & Power Options menu and choosing Enabled.
•
Unplug the TV for two minutes and then plug it back in. Turn the TV on and try again.
TV turns off unexpectedly
•
KidPass might have been set. Go to page 30 for instructions.
•
A Schedule Recurrence may have been set. In the master menu system go to Time then Schedule.
•
•
Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn the TV on again.
If this happens frequently, the voltage in your house may be abnormally high or low.
Sleep Timer or Energy Saver may have been set. Chapter 1 has more details.
TV turns on unexpectedly
•
Wake Timer might have been set. Go to page 15 for instructions.
•
You might have pressed CH+, CH- or OK on the remote accidentally.
Blank screen
•
Make sure the component connected to the TV is turned on, and the TV is tuned to the correct Video Input Channel (Channel 3/4,
VID1, S-VID, etc.)
•
•
Try another channel.
Press RESET, in case the picture controls are set too low.
No sound, picture okay
•
Maybe sound is muted. Press the volume up button to restore sound.
•
Maybe speakers are turned off. Check the Audio Output control panel in the master Sound menu. Go to page 11 for instructions.
•
•
Maybe Initial Volume is set low. Go to the master Sound menu to check.
If using S-Video or Y, Pb, Pr, remember to also connect the component's left and right audio output jacks to the TV.
Can’t select certain channel
•
Channel may be blocked or not approved in the Parental Control menu.
34
Chapter 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Noisy stereo reception
•
The station might be weak. Change the Sound Type in the Sound menu from stereo to mono.
No picture, no sound but TV is on
•
Maybe the cable/air setting is set to the wrong position. Select Signal Type from the master Setup menu. Go to Chapter 1 for more
information.
•
•
The channel might be empty — change channels.
If you’re trying to watch content from a component that’s connected to the TV (like a DVD player or VCR), press the INPUT button
on the remote control until the content appears.
Sound okay, picture poor
•
Check antenna connections. Make sure all of the cables are firmly connected to the jacks.
Black box appears on the screen
•
Closed-captioning might be on. Check Closed-Caption in the Setup menu. Go to page 16 for more information.
The Remote Control Doesn’t Work
•
•
•
Something might be between the remote and the remote sensor on the component. Make sure there is a clear path.
Maybe batteries in remote are weak, dead or installed incorrectly. Put new batteries in the remote.
You might need to reset the remote: remove batteries and press the number 1 button for at least 60 seconds. Release the 1 button
and replace the batteries.
•
•
Operation of certain remote control buttons might be restricted by master menu settings.
Maybe remote is in wrong configuration (TV1 or TV2) for that TV. Check the Remote Config. settings in the Access & Power Options
menu.
Problems with V-Chip/Parental Controls
The rating limits don’t work
•
You must lock the settings. Go to the Main menu, select Parental Control, then Lock Parental Controls to save your settings.
I don’t remember my password and I want to unlock the TV
•
Use the master remote to access the Password option in the Lock Par. Controls portion of the Parental Controls menu.
The V-Chip won’t let me watch a program even though it’s not rated as violent.
•
Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to View separately in order
to view movies with an NR rating.
•
Video Input Channels (VID, SVID) aren’t available unless they have been manually added to the channel list.
Chapter 5
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Menu Problems
•
•
•
•
•
•
Menu access may be blocked by ClonePRO programming.
Try unplugging the TV for two minutes and then plug it back in and turn it on.
The Energy Saver settings won’t work if the TV Power is set to On Always in the Access & Power Options menu.
The basic menu options might be restricted by master menu settings.
The ClonePRO might have disabled master menus.
Sleep and Schedule functions won’t work if the TV Power is set to On Always.
Care and Cleaning
CAUTION: Turn OFF your TV before cleaning.
You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet to help
assure adequate ventilation.
The TV’s screen may be cleaned with a soft, lint-free cloth as well. Take care not to scratch or mar the screen. If necessary,
you may use a cloth dampened with warm water. Never use strong cleaning agents, such as ammonia-based cleaners, or
abrasive powder. These types of cleaners will damage the TV.
While cleaning do not spray liquid directly on the screen, or allow liquid to run down the screen and inside the TV. Also, avoid placing drinks
or vases with water on top of the TV. This could increase the risk of fire or shock hazard or damage to the TV.
Caution: Using video games or any external accessory with fixed images for extended periods of time can cause them to be permanently
imprinted on the picture tube (or projection TV picture tubes). ALSO, some network/program logos, phone numbers, etc. may cause
similar damage. This damage is not covered by your warranty.
36
Chapter 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Limited Warranty
What your warranty covers:
•
Any defect in materials or workmanship.
For how long after your purchase:
•
•
•
One year for labor charges.
One year for parts.
Two years for picture tube.
(The warranty begins at time of first installation or 45 days after shipment, whichever comes first.)
What we will do:
•
•
Pay any Authorized RCA Commercial Television Service Center the labor charges to repair your television.
Pay any Authorized RCA Commercial Television Service Center for the new or, at our option, refurbished replacement parts
and picture tube required to repair your television.
How you get service:
•
Request service from any Authorized RCA Commercial Television Service Center, provided that your television is located
within the geographic territory covered by an Authorized Commercial RCA Television Service Center. If not, you must take
your television to the Service Center location at your own expense, or pay for the cost the Service Center may charge to
transport your television to and from your location.
•
•
To identify your nearest Authorized RCA Commercial Television Service Center, ask your distributor, visit www.
rcacommercial.com, look in the Yellow Pages, or call 1-800-880-5966.
Show the Authorized Service Center Representative your sales receipt or other evidence of purchase date or first rental.
What your warranty does not cover:
•
Customer instruction. (Your Owner’s Manual clearly describes how to install, adjust, and operate your television. Any
additional information should be obtained from your distributor or sales representative.)
•
•
•
•
•
•
•
•
•
Installation and related adjustments.
Acts of God, such as, but not limited to lightning damage.
Signal reception problems not caused by your television.
Damage from misuse or neglect.
Batteries.
Damage from images burnt onto the screen.
A television that has been modified or incorporated into other products.
A television purchased or serviced outside the USA.
In-room service.
Product registration:
•
Please complete and mail the Product Registration Card packed with your TV. It will make it easier to contact you should it
ever be necessary. The return of the card is not required for warranty coverage.
Limitation of Warranty:
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY TTE TECHNOLOGY, INC.,
ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
Continues on next page...
Chapter 5
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
•
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
TTE TECHNOLOGY, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF
THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE
WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
•
Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you.
•
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the USA:
This warranty does not apply. Contact your distributor for warranty information.
•
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such
service calls are the sole responsibility of the purchaser.
38
Chapter 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Description
Part No.Price
VH81 $3.95
VH82 $4.95
VH89 $5.95
VH83 $5.95
VH84 $9.95
VH976 $7.95
VH913 $14.95
VH47 $3.95
ANT200 $49.95
244888 $21.30
244889 $18.75
257195 $208.95
228449 $4.45
SCTV4000C $49.95
Remote Control These are the
remote controls that work with
your TV. Replacements or spares
can be ordered as needed.
CC
POWER SLEEP
SYSTEM
CCPOWER
SLEEP
CHAN
SYSTEM
VOL
VOL
GO CHAN
GO
MUTE BACK
Screw-on antenna cable (3-ft)
Screw-on antenna cable (6-ft)
Push-on antenna cable (6-ft)
Monaural VCR Dubbing Cable (6-ft)
Stereo VCR Dubbing Cable (6-ft)
S-Video Cable (6-ft)
MUTE BACK
GUIDE
INFO
INFO
GUIDE
OK
OK
MENU
CLEAR
MENU
CLEAR
1
2
5
8
0
3
6
9
1
2
5
8
0
3
6
9
4
7
4
7
INPUT
SKIP
INPUT
RESET
M A S T E R
CRK17TD1
Master
CRK17TC1
Basic
S-Video Cable (12-ft)
ClonePRO Clones settings for
multiple TVs. Replacements or
spares can be ordered as needed.
2-way Signal Splitter
Amplified Antenna
Basic Remote Control (CRK17TC1)
Master Remote Control (CRK17TD1)
ClonePRO Remote
257195
VH47
Audio•Video Adapter
2-way Signal Splitter helps you
connect to a second TV or VCR.
Surge Protector
Prices are subject to change without notice.
Amplified VHF/UHF/FM Antenna
allows you to easily switch
from the antenna signal to
cable or satellite easily without
disconnecting antenna.
HOW TO ORDER
ANT200
ON-LINE:Accessories may also be purchased at
Screw-on Cable attaches to the
round antenna connectors (called
75-ohm F-type) on the back of
your VCR or TV. The ends screw
onto the connectors for a secure
connection.
BY PHONE: To place your order by phone, have your Visa,
MasterCard or Discover Card ready and call 1-800-338-0376.
Use this number only to place an order for accessory items
listed on this page.
VH81 (3-ft)
VH82 (6-ft)
All accessories are subject to availability.
Where applicable, we will ship a superseding model.
Standard Audio/Video cable with
RCA-type phono plugs.
VH83
S-Video Cable has multi-pin
connectors on each end for
connecting S-Video components
to your TV.
VH913
Surge Protector provides eight
outlets, two coax cable/DBS
protection, telephone line
protection, surge stat indicator and
2100 joules protection.
PS83202C2
Chapter 5
39
Download from Www.Somanuals.com. All Manuals Search And Download.
As an ENERGY STAR® Partner, Thomson Inc. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
ENERGY STAR is a U.S. registered mark.
Please do not send any products to the Indianapolis address listed in this manual or on the carton.This will only add delays in
service for your product.
TTE Technology, Inc.
10330 North Meridian Street
Indianapolis, IN 46290
©2005 TTE Technology, Inc.
RCA and associated marks are trademarks of THOMSON S.A. used under license to TCL-Thomson Electronics (TTE).
Printed in USA
TOCOM 1644105A
Download from Www.Somanuals.com. All Manuals Search And Download.
|