R
3100 WOOD STOVE SERIES
Advanced Combustion Control (ACC)
Owner’s Manual
Installation and Operation
Models:
31M-ACC-MBK
31M-ACC-GT
31M-ACC-NT
31ST-ACC
Beaverton
Oregon USA
Tested and
Listed by
C
US
OMNI- Test Laboratories, Inc.
Step Top Uni-Body Model
(Pedestal Model Shown)
Millennium Model
CAUTION
DO NOT DISCARD THIS MANUAL
•
Read, understand and
follow these instructions
for safe installation and
operation.
•
Leave this manual with
party responsible for
use and operation.
•
Important operating
and maintenance
instructions included.
WARNING
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
If the information in these instruc-
tions is not followed exactly, a
fire may result causing property
damage, personal injury, or death.
Glass and other surfaces are hot
during operation and cool down.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
•
•
Keep children away.
CAREFULLY SUPERVISE children in same room as
appliance.
• Do not overfire - If heater or chimney con-
nector glows, you are overfiring. Overfiring
will void your warranty.
•
•
•
Alert children and adults to hazards of high
temperatures.
Do NOT operate with protective barriers removed or
door open.
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
Keep clothing, furniture, draperies and other
combustibles away.
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies recommends NFI certified
professionals, or technicians supervised by an
NFI certified professional.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may overfire and generate
poisonous gases (i.e. carbon monoxide).
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
TABLE OF CONTENTS
Section 1: Listing and Code Approvals
A. Appliance Certifications ......................4
B. Mobile Home Approved ......................4
C. Glass Specifications............................4
D. BTU & Efficiency Specifications..........4
Section 8: Operating Instructions (Cont’d)
H. Blower Operating Instructions.............29
I. Opacity (Smoke) .................................29
J. Overfiring ............................................29
K. Frequently Asked Questions...............30
Section 2: Getting Started
Section 9: Maintaining & Servicing Appliance
A. General Maintenance & Cleaning.......31-32
B. Glass Replacement.............................32
C. Firebrick Replacement........................33
D. Baffle Removal....................................34
E. Snap Disc Replacement .....................34
F. Tube Channel Replacement ...............35
A. Design, Installation & Location
Considerations....................................5
B. Fire Safety ..........................................5
C. Negative Pressure..............................6
D. Flue Draft Considerations...................7
E. Venting Systems.................................7
F. Tools and Supplies Needed................7
G. Inspect Appliance & Components.......7
H. Typical Stove System .........................8
Section 10: Troubleshooting........................36-37
Section 11: Reference Material
Section 3: Dimensions & Clearances
A. Appliance Dimensions ........................9-10
B. Clearances to Combustibles...............11
A. Exploded Drawings.............................38-40
B. Service Parts & Accessories...............41-43
C. Service & Maintenance Log................44
D. Homeowner’s Notes ...........................45-46
E. Warranty Policy...................................47
F. Contact Information.............................48
Section 4: Installation Consideration
A. Hearth Requirements .........................12-13
B. Outside Air ..........................................14
C. Blower Installation...............................15
Section 5: Chimney Requirements
A. Venting Components..........................16
B. Chimney Systems...............................16-18
C. Installing Chimney Components .........18
D. Chimney Termination Requirements ..19
E. 2-10-03 Rule........................................19
Section 6: Mobile Home...............................20
Section 7: Appliance Set-Up
A. Pedestal & Ash Removal System
(ARS) Installation...............................21-22
B. Leg Kit & Ash Removal System
(ARS) Installation...........................23
C. Door Handle Assembly.......................24
D. Blower Speed Adjustment ..................24
Section 8: Operating Instructions
A. Fire Safety...........................................25
B. Wood Selection & Storage..................25
C. Burning Process..................................25-26
D. Automatic Combustion Control (ACC)....26
E. Air Controls .........................................26-27
F. Burn Rates & Operating Efficiency .....27
G. Building A Fire.....................................28
Page 3
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Listing and Code Approvals
1
D. BTU & Efficiency Specifications
A. Appliance Certification
3100 Millennium & Step Top (ACC)
Uni-Body
1.1 grams per hour
Model:
EPA Certified:
Efficiency:
79.51%
11,800 to 32,000
up to1,800 sq ft
6 inches
Laboratory:
Report No & Date:
Type:
OMNI Test Laboratories, Inc.
061-S-66-6
BTU Output:
Heating Capacity:
Vent Size:
Wood Stove
Standard:
UL1482 and ULC S627 and (UM)
84-HUD, Mobile Home Approved.
2 cubic feet
18 inches
Firebox Size:
Max Wood Length:
Fuel:
Cord Wood
325 lbs
The Quadra-Fire 3100 Series Wood Stove (ACC) meets the
U.S. Environmental Protection Agency’s 1990 particulate
emission standards.
Shipping Weight:
B. Mobile Home Approved
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specifications and/or price without notice.
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of
the mobile home floor, ceiling, and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home and use only listed double-wall connector
pipe. Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation
C. Glass Specifications
This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the UL1482,
(UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S627
and CAN/CSA-B365 Installation Codes in Canada.
Page 4
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Getting Started
2
B. Fire Safety
A
. Design, Installation & Location Considerations
Consideration must be given to:
To provide reasonable fire safety, the following should be
given serious consideration:
•
•
•
•
Safety
Convenience
Traffic flow
Chimney and chimney connector required
1. Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
It is a good idea to plan your installation on paper, using exact
measurements for clearances and floor protection, before
actually beginning the installation. If you are not using an
existing chimney, place the appliance where there will be a
clear passage for a factory-built listed chimney through the
ceiling and roof.
2. A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
We recommend that a qualified building inspector and your
insurance company representative review your plans before
and after installation
3. A practiced evacuation plan, consisting of at least two
escape routes.
4. A plan to deal with a chimney fire as follows:
If this appliance is in an area where children may be near it
is recommended that you purchase a decorative barrier to go
in front of the appliance. Remember to always keep children
away while it is operating and do not let anyone operate
this appliance unless they are familiar with these operating
instructions.
In the event of a chimney fire:
a. Notify fire department
b. Prepare occupants for immediate evacuation.
c. Close all openings into the stove.
d. While awaiting fire department, watch for ignition
of adjacent combustibles from overheated stove
pipe, hot embers or sparks from the chimney.
Service / Maintenance Tip:
In order to replace the tube channel a clearance of 19
inches (483mm) is required on the right side of stove in
order to remove the tubes with the stove in place. If space
is not available, the stove will have to be disconnected from
the chimney to proceed with the tube replacement. See
page 35.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
•
•
•
Installation and use of any damaged appliance.
Modification of the appliance.
CAUTION
Installation other than as instructed by Hearth & Home
Technologies.
Check building codes prior to installation.
•
Installation MUST comply with local, regional, state and
national codes and regulations.
•
•
•
•
Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Operating appliance without fully assembling all
components.
•
Consult insurance carrier, local building, fire officials or
authorities having jurisdiction about restrictions, installation
inspection, and permits.
Operating appliance without legs attached (if supplied with
unit).
Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
WARNING
Asphyxiation Risk.
WARNING
•
Do NOT connect this unit to a chimney flue
Fire Risk.
servicing another appliance.
•
Do not operate appliance before reading and
understanding operating instructions.
•
Do NOT connect to any air distribution duct or
system.
May allow flue gases to enter the house.
•
Failure to operate appliance properly may
cause a house fire.
Page 5
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Negative Pressure
To minimize the affects of negative air pressure the following
must be considered:
Draft is the pressure difference needed to vent appliances
successfully. Considerations for successful draft include:
•
Install the outside air kit. Install the intake on the
side of the house towards prevailing winds during the
heating season.
•
•
Preventing negative pressure
Location of appliance and chimney
•
•
Ensure adequate outdoor air is supplied for combus-
tion appliances and exhaust equipment.
Negative pressure results from the imbalance of air avail-
able for the stove to operate properly. Causes for this imbal-
ance include:
Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appli-
ance,
•
•
•
Exhaust fans (kitchen, bath) etc.)
Range hoods
•
•
Avoid installing the appliance near doors, walkways
or small isolated spaces.
Combustion air requirements for furnaces, water
heaters and other combustion appliances
Recessed lighting should be of “sealed can” design;
attic hatches weather stripped or sealed; and attic
mounted duckwork and air handler joints and seams
taped or sealed.
•
•
Clothes dryers
Location of return-air vents to furnace or air condi-
tioning
•
•
Imbalances of HVAC air handling system
Upper level air leaks
•
•
•
Recessed lighting
Attic hatch opening
Duct leaks
WARNING
Asphyxiation Risk.
•
•
Negative pressure can cause spillage of com-
bustion fumes, soot and carbon monoxide.
Appliance needs to draft properly for safety.
Recommended
Location
Recommended
Location
Marginal
Location
Location
Not
Recommended
Location NOT
Recommended
Windward
Outside Termination Cap
Leeward
Multi-level Roofs
Figure 6.1
Page 6
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
F. Tools And Supplies Needed
D. Flue Draft Considerations
Location of the appliance and chimney will affect perfor-
mance. As shown in Figure 6.1 on page 6 the chimney
should:
Before beginning the installation be sure that the following
tools and building supplies are available.
•
Be installed through the warm space enclosed by the
building envelope. This helps to produce more draft,
especially during lighting and die down of the fire.
Framing Material
Hi-Temp Caulking Material
Gloves
Reciprocating saw
Pliers
Hammer
Framing Square
Electric Drill & Bits (1/4”)
Safety Glasses
1/2 in. - 3/4 in. length, #6 or
#8 self drilling screws (need 3
per pipe section connection)
Phillips Head Screwdriver
Flat Blade Screwdriver
Plumb Line
Level
Tape Measure
•
•
Penetrate the highest part of the roof. This minimizes
the affects of wind turbulence and down drafts.
Consider the appliance location in order to avoid
floor and ceiling attic joists and rafters.
Exterior conditions such as roof line, surrounding trees,
prevailing winds and nearby hills can influence stove
performance. Your local dealer is the expert in your geographic
area and can usually make suggestions or discover solutions
that will easily correct your flue problem.
G. Inspect Appliance & Components and
Pre-Use Check List
T
o be sure that your appliance burns properly, the chimney
draft (static pressure) should be approximately -.04 inch water
column (W.C.) during a low burn and -.10 inch W.C. during a
high burn, measured 6 inches (152mm) above the top of the
appliance after one hour of operation at each burn setting.
1.
2.
Place the appliance in a location near the final
installation area and follow the procedures below:
Open the appliance and remove all the parts and
articles packed inside the Component Pack. Inspect
all the parts and glass for shipping damage. Contact
your dealer if any irregularities are noticed.
NOTE: These are guidelines only, and may vary somewhat
for individual installations.
3.
4.
5.
6.
7.
All safety warnings have been read and followed.
This Owner’s Manual has been read.
Floor protection requirements have been met.
Venting is properly installed.
E. Venting Systems
The venting system consists of a chimney connector (also
known as stove pipe) and a chimney. These get extremely
hot during use. Temperatures inside the chimney may
exceed 2000°F (1100°C) in the event of a creosote fire. To
protect against the possibility of a house fire, the chimney
connector and chimney must be properly installed and
maintained. An approved thimble must be used when a
connection is made through a combustible wall to a chimney.
Achimney support package must be used when a connection
is made through the ceiling to a prefabricated chimney.
These accessories are absolutely necessary to provide
safe clearances to combustible wall and ceiling material.
Follow venting manufacturer’s clearances when installing
venting system.
The proper clearances from the appliance and chim-
ney to combustible materials have been met.
8.
The masonry chimney is inspected by a professional
and is clean, or the factory built metal chimney is
installed according to the manufacturer’s instruc-
tions and clearances.
9.
The chimney meets the required minimum height.
All labels have been removed from the glass door.
10.
11.
Plated surfaces have been wiped clean, if appli-
cable.
12.
A power outlet is available nearby if installing
optional blower assembly.
WARNING
WARNING
Fire Risk.
Asphyxiation Risk.
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
•
Do NOT connect this unit to a chimney flue
servicing another appliance.
•
•
•
Do NOT install damaged components.
Do NOT install incomplete components.
Do NOT install substitute components.
•
Do NOT connect to any air distributon duct
or system.
May allow flue gases to enter the house.
Report damaged parts to dealer.
Page 7
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
H. Typical Stove Systems
Spark Arrestor Cap
Concrete Cap
Fireclay Flue Liner
With Air Space
Stove system with masonry chimney
consists of:
Rafter
• Stove
Flashing
Eave
• Chimney Connector (stove pipe)
• Thimble
1" (25mm) Clearance
With Firestop
Ceiling Joist
• Masonry Chimney
• Hearth Pad Floor Protection
Combustible Wall
Thimble,
12" (305mm)
Of Brick
Sheathing
Outside Air Rear Vent
Outside Air
Termination Cap
Floor
Protector
Airtight
Cleanout Door
Figure 8.1 Masonry Chimney
Stove system with prefabricated
metal chimney consists of:
Listed Termination Cap
Storm Collar
Flashing
Listed Termination Cap
• Stove
Chimney Connector
(stove pipe)
•
Roof Brace (if required)
• Thimble (for exterior
chimney)
Storm Collar
Flashing
Listed Chimney
Ceiling Support
• Firestops
• Insulations Shields
• Storm Collar and Flashing
• Termination Cap
Trim Collar on
Inside Wall
Listed Chimney
Insulated "T "
• Hearth Pad Floor Protec-
tion
Chimney
Connector
Chimney
Connector
Wall Support
Floor
Protector
Floor
Protector
Figure 8.2 Exterior Prefabricated Chimney
Figure 8.3 Interior Prefabricated Chimney
Page 8
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Dimensions and Clearances
3
25 in. (635mm)
A. Appliance Dimensions
C
L
9-15/16 in.
(237mm)
12-1/2 in.
(318mm)
NOTE: Flue Collar size is 6 inch
(152mm) diameter (ID)
10-15/16 in.
(271mm)
15-1/16 in.
(383mm)
14-15/16 in.
(373mm)
18-15/16 in.
(475mm)
Millennium Model
30 in.
(762mm)
Figure 9.1 Front View
26-11/16 in. (668mm)
24-5/16 in. (618mm)
6-11/16 in.
(170mm)
C
L
11-1/2 in.
(292mm)
16 in. (406mm)
20-3/4 in. (527mm)
Figure 9.2 Side View
Page 9
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Appliance Dimensions (Cont’d)
3100 Step Top Pedestal Model
3100 Step Top Leg Model
25 in. (635mm)
C
L
12-1/2 in.
(318mm)
9-5/16 in.
(237mm)
14-15/16 in.
(379mm)
19-1/16 in.
(484mm)
33-1/8 in.
(841mm)
10-15/16 in.
(278mm)
15-1/16 in.
(383mm)
34-1/4 in.
(870mm)
18 in.
(457mm)
23-7/8 in.
(606mm)
Figure 10.1
Figure 10.3
26-11/16 in.(678mm)
24-5/16 in. (618mm)
6-11/16 in.
(170mm)
3-1/2 in.
(89mm)
15-3/8 in. (391mm)
C
3-11/16 in. (94mm)
L
Back of Stove to Glass
23-3/8 in.
(594mm)
10-3/8 in.
(264mm)
11-1/2 in.
(292mm)
16 in. (406mm)
21-1/8 in. (537mm)
20-3/4 in. (527mm)
Figure 10.2
Figure 10.4
Page 10
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
B. Clearances to Combustibles (UL and ULC)
BACKWALL / SIDEWALL
ALCOVE SIDE VIEW
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
A
B
G
A
C
D
B
H
*
90° OFF TOP
UP & OUT CEILING
CLEARANCE
G
STOVE TO CEILING
CLEARANCE
CORNER INSTALLATION
E
ALCOVE TOP VIEW
F
C
D
E
F
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.
A
B
C
D
E
F
G
H
INSTALLATION: Full Vertical OR Horizontal with Minimum 2 FT Vertical Off Stove Top
SINGLE WALL PIPE
Flat Top Model
Step-Top Model
15.25 (387) 11.75 (298) 25.5 (648) 16 (406)
12 (305) 8.5 (216) 22 (559) 12.5 (318)
8 (203)
17 (432)
48 (1220)
12 (305)
12 (305)
5.5 (140 14.5 (368) 48 (1220)
DOUBLE WALL PIPE
Flat Top Model
10.5 (267) 6.5 (165)
10 (228) 6 (152)
22 (559)
13 (330)
6.5 (165) 15.5 (394) 48 (1220)
9 (229)
9 (229)
Step-Top Model
20.5 (521) 11 (279)
4 (102)
8 (203)
13 (330)
17 (432)
48 (1220)
48 (1220)
INSTALLATION: 90° Elbow Off Top of Stove Through Backwall
SINGLE WALL PIPE
Flat Top Model
Step-Top Model
12 (305)
10 (254)
8.5 (216)
6 (152)
22 (559)
20.5 (521) 11 (279)
13 (330)
12 (305)
12 (305)
5.5 (140) 14.5 (368) 48 (1220)
DOUBLE WALL PIPE
Flat Top Model
Step-Top Model
8 (203)
10 (254)
4.5 (114) 17.5 (445) 8.5 (216)
6 (152) 20.5 (521) 11 (279)
6.5 (165) 15.5 (394) 48 (1220)
9 (229)
9 (229)
4 (102)
13 (330)
48 (1220)
INSTALLATION: ALCOVE Six inch (6") (152mm) diameter listed Double Wall air insulated connector pipe with UL103 HT* listed
factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove
shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of unit, and the referenced clearances.
*In Canada must comply with CAN/ULC-S269 M87 for the 650oC Factory-built chimney.
DOUBLE WALL PIPE
Flat Top Model
11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368)
10 (254) 6.5 (152) 20.5 (521) 11 (279)
N/A
N/A
N/A
N/A
48 (1220)
48 (1220)
*
*
Step-Top Model
* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED
SERVICE / MAINTENANCE TIP
WARNING
In order to replace the tube channel assembly a clearance
of 19 inches (483mm) is required on the right side of stove in
order to remove the tubes with the stove in place. If space
is not available, the stove will have to be disconnected from
the chimney to proceed with the tube replacement.
Fire Risk.
•
Comply with all minimum clearances to
combustibles as specified.
•
Failure to comply may cause house fire.
Page 11
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Installation
4
In Canada, similar floor protection must be provided 18
inches (457mm) in front and 8 inches (203mm) from the
sides and rear of the stove. *See exception.
A. Hearth Protection Requirements
FLOOR PROTECTION: Floor protector must be non-com-
bustible material, extending beneath heater and to the front,
sides and rear as indicated. The floor must be non-com-
bustible or otherwise adequately protected from radiant heat
given off by the unit and from sparks and falling embers. A
layer of thin brick or ceramic tile over a combustible floor is
not sufficient.
*EXCEPTION: Non-combustible floor protections must
extend beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side.
See Figure 12.4.
WARNING
For the Millennium Model In US installations, it is nec-
essary to install a floor protector of a minimum of 3/8 inch
(9.5mm) thick metal clad millboard or equivalent a minimum
of 16 inches (406mm) in front of glass and 8 inches (203mm)
to both sides of the fuel loading door. Open the door and
measure 8 inches (203mm) from the side edge of the open-
ing in the face of the appliance. *See exception.
Fire Risk.
• Hearth pads must be installed exactly as
specified.
High temperatures or hot embers may ignite
concealed combustibles.
Millennium Model
49-7/8 in.
27-5/8 in.
4-7/8 in.
3-1/8 in."
39-5/8 in.
minimum
Fuel loading door
49-7/8 in.
8 in.
USA
16" from glass
31-5/8 in.
minimum
USA
27-5/8 in.
Figure 12.1
Figure 12.3
USA required
Canada recommended
203mm (8 in.)
203mm
(8 in.)
203mm
(8 in.)
1260mm
(49-5/8 in.)
minimum
457mm (18 in.)
CANADA
Must extend 2 in. (51mm) beyond
each side of pipe (shaded area)
1041mm (41 in.)
minimum
Figure 12.2
Figure 12.4
Page 12
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Step-Top Uni-Body Model
For the Step Top Pedestal Model In US installations, it is
necessary to install a floor protector of a minimum of 3/8 inch
(9.5mm) thick metal clad millboard or equivalent a minimum of
16 inches (406mm) in front of glass and 8 inches (203mm)
to both sides of the fuel loading door. Open the door and
measure 8 inches (203mm) from the side edge of the open-
ing in the face of the appliance. *See page 12 for Canadian
clearances and horizontal venting exception.
For the Step Top Leg Model In US installations, it is nec-
essary to install a floor protector of a minimum thickness of
1-1/4 inch (32mm) or 1/2 inch of “k” value of 0.84 thick metal
clad millboard or equivalent a minimum of 16 inches (406mm)
in front of glass and 8 inches (203mm) to both sides of the
fuel loading door. Open the door and measure 8 inches
(203mm) from the side edge of the opening in the face of
the appliance. *See page 12 for Canadian clearances and
horizontal venting exception.
49-7/8 in.
27-5/8 in.
3-1/4 in.
4-3/4 in.
39-5/8 in.
minimum
Fuel loading door
49-7/8 in.
8 in.
16 in. from glass
USA
31-5/8 in.
minimum
USA
27-5/8 in.
Figure 13.1
Figure 13.3
USA required
Canada recommended
203mm (8 in.)
203mm
(8 in.)
203mm
(8 in.)
1254mm
(49-3/8 in.)
minimum
457mm (18 in.)
CANADA
Must extend 2 in. (51mm) beyond
each side of pipe (shaded area)
1041mm (41 in.)
minimum
Figure 13.4
Figure 13.2
NOTE:
•
•
•
•
Illustrations and photos reflect typical installations and are FOR DESIGN PURPOSES ONLY.
Illustrations/diagrams are not drawn to scale.
Actual installation may vary due to individual design preference
Hearth & Home Technologies reserves the right to alter its products.
Page 13
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
B. Outside Air Kit Installation
A source of air (oxygen) is necessary in order for combus-
tion to take place. Whatever combustion air is consumed
by the fire must be replaced. Air is replaced via air leak-
age around windows and under doors. In homes that have
tightly sealed doors and windows, an outside air source is
needed. An optional Outside Air Kit is available.
WARNING
Fire Risk.
Asphyxiation Risk.
Do not draw outside combustion air from:
•
•
•
Wall, floor or ceiling cavity
Enclosed space such as an attic or garage
Close proximity to exhaust vents or
chimneys
Included in OAK-ACC: Termination cap, (2) wire ties, flex
adapter, and fasteners
Fumes or odor may result
Included in SRV7033-041:Cover plate and sealing rope (see
Floor Installation Alternative below,
Figure 14.2)
WARNING
Asphyxiation Risk.
Items Needed for Installation (not supplied)
Outside air inlet must be located to prevent block-
age from:
• 4 inch flex aluminum pipe, or if using alternate material,
then it shall be made from durable, non-combustible,
heat resistant material up to 350oF. Cut the pipe to
the required length for your installation.
•
•
•
Leaves
Snow or ice
Other debris
• Phillips head screw driver
• Silicone sealant
Block may cause combustion air starvation
• Drills and saws necessary for cutting holes through
the wall or flooring in your home.
Smoke spillage may set off alarms or irritate sensi-
tive individuals.
WARNING
Asphyxiation Risk.
1. Remove all materials from packing box.
2. Using a #2 Phillips screw driver attach the flex adapter
Length of outside air supply duct shall NOT exceed
the length of the vertical height of the exhaust flue.
to the stove using 4 screws. Figure 14.1
3. Remove circular” knock-out” in the base of the pedestal.
• Fire will not burn properly
• Smoke spillage occurs when door is opened due
4. Floor & Rear Installation: Cut a 4 inch (102mm)
hole in outside wall or floor to accommodate outside
air piping. Use 4 inch (102mm) aluminum metal flex or
rigid piping to directly connect outside air to appliance
intake. Use the supplied termination cap with a rodent
screen. Seal between the wall (or floor) and the pipe
with silicone to prevent moisture penetration.
to air starvation.
5. Floor Installation Alternative: In some instances you
may not be able to install the flex pipe as show in Figure
14.1. If that is the case, you will need to order SRV7033-
041 which includes a cover plate and sealing rope as
shown in Figure 14.2. The goal is to seal the pedestal
so no room air can leak into the pedestal.
Flex Adapter
Wire Tie
Terminatio
Cap
Rope to Seal
Pedestal
Cover
Plate
Remove circular
“knock-out” in base
of pedestal.
Flex Line
Wire Tie
Figure 14.2 - Floor Installation Alternative
Figure 14.1 - Floor & Rear Installation
Page 14
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Blower (Optional)
CAUTION
1. Remove the 3 bolts (1/4”-20 Phillips head) on the outer
skin at the bottom rear of appliance.
Shock Risk.
2. Align holes in mounting flange of blower with bolt holes in
appliance. Blower should be positioned at bottom of rear
outer skin as shown in Figure 15.1.
•
Do NOT remove grounding prong from plug.
•
Plug directly into properly grounded 3 prong
receptacle.
•
•
Route cord away from appliance.
3. Re-insert and tighten bolts, securing blower onto outer
wall of appliance.
Do NOT route cord under or in front of appliance.
4. Place the bracket containing the snap disc and magnet
under the bottom left rear corner as shown in Figure 15.1.
See page 29 for detailed operating instructions for the
blower and snap disc.
Snap Disc
Bracket
with Magnet
Secure wires
with wire tie.
MANUAL: Over-rides the
Snap Disc
MANUAL
FAN
AUTO
AUTO: Fan will turn ON/OFF
Automatically by the Snap Disc
LOW
HIGH
OFF
Controls the Fan Speed
Figure 15.1
Page 15
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Chimney Requirements
5
A. Venting Components
Chimney Connector:
B. Chimney Systems
Prefabricated Metal Chimney
It is also known as flue pipe or stove pipe. The chimney
connector joins the stove to the chimney. It must be a 6 inch
(152mm) minimum diameter 24 gauge mild steel black or
26 gauge blued steel, or an approved air-insulated double
wall venting pipe.
•
•
•
•
Must be a 6 inch (152mm) diameter (ID) high temperature
chimney listed to UL 103 HT (2100 F) or ULC S629M.
o
Must use components required by the manufacturer for
installation.
Must maintain clearances required by the manufacturer
for installation.
Thimble:
A manufactured or site-constructed device installed in
combustible walls through which the chimney connector
passes to the chimney. It is intended to keep the walls
from igniting. Site constructed thimbles must meet
NFPA 211 Standards. Prefabricated must be suitable
for use with selected chimney and meet UL103 Type HT
Standards. Follow instructions provided by the manufacturer
for manufactured thimbles for masonry chimney and
prefabricated chimneys.
Refer to manufacturers instructions for installation.
NOTE: In Canada when using a factory-built chimney it must
be safety listed, Type UL103 HT (2100oF) CLASS “A” or
conforming to CAN/ULC-S629M, STANDARD FOR 650oC
FACTORY-BUILT CHIMNEYS.
Chimney:
Listed Termination Cap
Storm Collar
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements specified
in Section 5B.
Flashing
Listed Termination Cap
Roof Brace (if required)
Listed Chimney
Ceiling Support
Storm Collar
Flashing
Chimney
Connector
Trim Collar on
Inside Wall
Listed Chimney
Insulated "T "
Chimney
Connector
Wall Support
Floor
Protector
Floor
Protector
Figure 16.2 - Prefabricated Interior Chimney
Figure 16.1 Prefabricated Exterior Chimney
Page 16
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Thimble
C
L
Site constructed for masonry chimney installation:
ceiling
Components
13.5” below ceiling to top
of opening
• A minimum length of 12 inches [305mm] (longer for
thicker walls) of solid insulated factory-built chimney
length constructed to UL 103 Type HT 8 inch (203mm)
inside diameter. Chimney needs to extend a minimum
of 2 inches (51mm) from the interior wall and a mini-
mum of 1 inch (25mm) from the exterior wall.
Wall
or top of opening is a min.of
4.5” below min.clearance
specified by connector mfg.
Minimum18.0”
NFPA 211
1.5 2x2 framing stud
2.0 min air clearance
1.0 min air clearance
4.5
1.5”
2.0”
1.0”
• Wall spacer, trim collar and wall band to fit solid pack
chimney selected.
17.0” OD
14.0” ID
8.0”
C
L
1.0”
2.0”
• Minimum 8 inch (203mm) diameter clay liner section (if
not already present in chimney) and refractory mortar.
1.5”
Center of Hole
Thimble
Air Clearances
• Masonry chimney clearance must meet NFPA 211 mini-
mum requirement of 2 inches (51mm) to sheet metal
supports and combustibles.
Include depth
of hearth pad
• Minimum of 1 inch (25mm) clearance around the chim-
ney connector.
• Top of wall opening is a minimum of 13-1/2 inches
(343mm) from ceiling or 4-1/2 inches (114mm) below
minimum clearance specified by chimney connector
manufacturer. NFPA 211 minimum vertical clearance of
18 inches (457mm) from chimney connector and ceil-
ing or minimum recommended by chimney connector
manufacturer. Figure 17.1.
Figure 17.1
Solid Pack Chimney with Metal Supports as a Thimble
Instructions:
1. Open inside wall at proper height for the chimney con-
Fire Clay Flue
Liner
with Airspace
nector to entry the masonry chimney. Figure 17.1
2. Entry hole to masonry chimney must be lined with an 8
inch (203mm) minimum diameter clay liner, or equiva-
lent, secured with refractory mortar.
Masonry
Chimney
Trim Collar
3. Construct a 17 inch x 17 inch (432mm x 432mm) out-
side dimension frame from 2 x 2 framing lumber to
fit into wall opening. Inside opening of frame should
be no less than 14 inch x 14 inch (356mm x 356mm).
Figure 17.1.
Wall Spacer
Chimney Section
with 2 inch
(51mm)
Clearance to
Combustibles
Wall Band to
Secure Chimney
Section
4. Attach the wall spacer to the chimney side of the
frame.
Chimney
Connector
Wood Studs Used
for Framing - Spaced
2 inch (51mm)
clearance from
Masonry Chimney
5. Nail the frame into the wall opening. The spacer should
be on the chimney side.
6. Insert the section of the solid insulated chimney into
the outer wall of the masonry chimney.
Figure 17.2
7. Tightly secure the length of the solid insulated chimney
with the wall band to the masonry chimney.
WARNING
Fire Risk.
8. Insert a section of chimney connector into the chimney.
Make sure it does not protrude past the edge of the
clay chimney liner inside the chimney.
Do NOT pack insulation or other combustibles between
spacers.
•
ALWAYS maintain specified clearances around vent-
ing and spacers.
9. Seal the end of the chimney connector to the clay liner
with refractory mortar.
•
Install spacers as specified.
Failure to keep insulation or other material away from
vent pipe may cause fire.
10. Install trim collar around the sold pack chimney section
.
Page 17
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Solid Pack Chimney with Metal Supports as a
Thimble (Cont’d)
C. Installing Chimney Components
Chimney Connector
Single wall connector or stove pipe.
Min. Chimney Clearance to
This must be at least 24 gauge mild steel or 26 gauge blue
steel. The sections must be attached to the appliance and to
each other with the crimped (male) end pointing toward the
stove. All joints, including the connection at the flue collar,
should be secured with 3 sheet metal screws. Make sure
to follow the minimum clearances to combustibles. Where
passage through the wall, or partition of combustible con-
struction is desired in Canada, the installation shall conform
to CAN/CSA-B365.
Wall Spacer and
Combustibles - 2 inch (51mm)
Min. Clearance
2 inch (51mm)
1 inch (25mm) Air
Space to Chimney
Section
Chimney Flue
Liner
Fireclay
Liner or
Equivalent
Chimney
Connector
Chimney Section
Trim Collar
Wall Band
Wall Spacer
Factory-built listed chimney connector (vented).
Alisted connector (vented) must be used when installing this
unit in a mobile home. The listed connectors must conform
to each other to ensure a proper fit and seal.
Masonry Chimney
Constructed to NFPA 211
Figure 18.1
Chimney Height / Rise and Run
Crimped
Flue Gas
End
Toward
This product was designed for and tested on a 6 inch (152mm)
chimney, 14 to 16 feet (420-480cm) high, (includes stove
height) measured from the base of the appliance. The further
your stack height or diameter varies from this configuration,
the possibility of performance problems exists.
Direction
Stove
Chimney height may need to be increased by 2 - 3% per
each 1000 feet above sea level. It is not recommended to
use offsets or elbows at altitudes above 4000 feet above sea
level or when there are other factors that affect flue draft.
Secure pipe sections with a
minimum of 3 screws
Figure 18.2 Chimney Connector (Stove Pipe)
WARNING
WARNING
Fire Risk.
Fire Risk.
Follow Chimney Connector Manufacturer’s
Instructions for Proper Installation.
Inspection of Chimney:
•
•
•
Chimney must be in good condition.
Meets minimum standard of NFPA 211
ONLY use connector:
•
Within the room, between appliance and ceiling or wall.
Factory-built chimney must be 6 inch
(152mm) UL103 HT.
Connector shall NOT pass through:
•
•
•
Attic or roof space
Closet or similar concealed space
Floor or ceiling
Maintain minimum clearances to combustibles
WARNING
Asphyxiation Risk.
WARNING
•
Do NOT connect this unit to a chimney flue
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appli-
ance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
servicing another appliance.
•
Do NOT connect to any air distribution duct
or system.
May allow flue gases to enter the house.
Page 18
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
D. Chimney Termination Requirements
NOTE:
Follow manufacturers instructions for clearance, securing,
•
•
Chimney performance may vary.
flashing and terminating the chimney.
Trees, buildings, roof lines and wind conditions affect
performance.
•
•
Must have an approved and listed cap
•
Chimney height may need adjustment if smoking or
overdraft occurs.
Must not be located where it will become plugged by
snow or other material
•
Must terminate at least 3 feet (91cm) above the roof
and at least 2 feet (61cm) above any portion of the
roof within 10 feet (305cm).
•
Must be located away from trees or other struc-
tures
E. 2-10-3 Rule
These are safety requirements and are not meant to assure proper flue draft.
Less than 10 ft. (305cm)
2 ft. (61cm)
3 ft. (91cm)
2 ft. (61cm)
Minimum
10 ft. (305cm) To Nearest Roofline
3 ft. (91cm)
Minimum
Pitched Roof
Figure 19.1
Less than 10 ft. (305cm)
2 ft. (61cm)
3 ft. (91cm)
Minimum
2 ft. (61cm)
10 ft. (305cm) To Nearest Roofline
3 ft. (91cm)
Minimum
Figure 19.2
Pitched Roof
7033-277C
Page 19
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Mobile Home Installation
6
You must use a Quadra-Fire Outside Air Kit Part
OAK-ACC and (depending on floor installation,
Part SRV7033-041) for installation in a mobile
home.
SparkArestor Cap
Roof Flashing
1. An outside air inlet must be provided for combustion See
Storm Collar
page 14 for installation information.
2. Appliance must be secured to the mobile home structure
by bolting the pedestal through hearth pad and into
floor.
3. Appliance must be grounded with #8 solid copper
grounding wire or equivalent and terminated at each end
with N.E.C. approved grounding device.
Joist Shield/Firestop
Double wall
connector pipe
4. Appliance must be installed with an approved UL103 HT
ventilated chimney connector, UL103 HT chimney, and
terminal cap with spark arrestor. Never use a single wall
connector (stove pipe) in a mobile home installation. Use
only double-wall connector pipe, Dura-Vent DVL, Selkirk
metalbestos DS or Security DL double-wall connector or
any listed double-wall connector pipe.
5. In Canada, this appliance must be connected to a 6 inch
(152mm) factory-built chimney conforming to CAN/ULC-
629M, STANDARD FOR FACTORY BUILT CHIMNEYS.
OutsideAir
RearVent
6. Follow the chimney and chimney connector manufacturer’s
instructions when installing the flue system for use in a
mobile home.
Floor Protector
7. Maintain clearance to combustibles.
8. Floor protection requirements must be followed
precisely.
Outside Air Floor Vent
9. Use silicone to create an effective vapor barrier at the
location where the chimney or other component penetrates
to the exterior of the structure.
Figure 20.1
NOTE: Offsets from the vertical, not exceeding 45°, are
allowed per Section 905(a) of the Uniform Mechanical Code
(UMC). Offsets greater than 45° are considered horizontal
and are also allowed, providing the horizontal run does not
exceed 75% of the vertical height of the vent. Construction,
clearance and termination must be in compliance with the
UMC Table 9C. This installation must also comply with NFPA
211.
CAUTION
Maintain structural integrity of mobile home:
Floor, wall, ceiling and/or roof.
Do NOT cut through:
•
•
•
Floor joist, wall, studs or ceiling trusses.
Any supporting material that would affect the structural
integrity.
NOTE: Top sections of chimney must be removable to allow
maximum clearance of 13.5 feet (411cm) from ground level
for transportation purposes.
WARNING
Asphyxiation Risk.
10. Burn wood only. Other types of fuels may generate
poisonous gases (e.g., carbon monoxide).
11. If unit burns poorly while an exhaust blower is on in
home, (i.e., range hood), increase combustion air.
•
Never install in a sleeping room.
Consumes oxygen in the room.
12. Installation shall be in accordance with the Manufacturers
Home & Safety Standard (HUD) CFR 3280, Part 24.
Page 20
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Appliance Set Up
7
A. Pedestal Assembly and Ash Removal
System (ARS) Installation for Step Top
Uni-body
NOTE: The Ash Removal System, must be
installed first before installing the pedestal.
Included in Kit: Door assembly, door handle & magnet,
ash grate, ash grate channel, ash drawer, fastener package.
A cover plate that is required for a floor outside air instal-
lation on a pedestal model is also included, If not needed,
discard.
Remove for
installation and
then re-install
Figure 21.1
Tools Required: Phillips head screw driver, 7/16 socket
wrench, 3/32 and 5/36 Allen wrench.
Begin installing the ARS System.
1. Remove 2 bricks as shown in Figure 21.1
Door Handle
Gasket
2. Lay body of stove on its back on a protective pad or pallet.
3. Remove the 2 nuts and 2 bolts holding the grate in place
and set the grate aside. Discard the 2 nuts. Install the
gasket over the 4 protruding screws. Figure 21.2.
Lay stove flat on
protective padding or
pallet
4. Install ash door assembly by sliding the rod at an angle
into the slot on the left side and sliding over the 4 screws
protruding from the bottom of the stove. Secure with nuts
provided. Figure 21.2.
Magnet
Slide rod at an
angle into slot
5. Install magnet using a Phillips head screw driver. This
magnet will hold the door handle in an open position
which in turn holds the ash door open so ashes can be
brushed into the ash drawer. Figure 21.2.
Ash Door
Assembly
Figure 21.2
6. Install door handle by placing over rod and sliding to the
right. While in an open position, line up the set screw with
the flat side of the rod and tighten the set screw using
a 3/32 Allen wrench. The set screw needs to be snug.
Figure 21.3.
Set Screw
(align with flat
side of rod)
WARNING
Do NOT operate before fully assembling components.
Burning your stove without a pedestal or leg kit
attached:
Ash Door Rod shown
in installed position
•
•
Will void your warranty.
May result in property damage or personal injury.
Door handle must be
in open position to
tighten set screw
Figure 21.3
Page 21
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Pedestal and Ash Removal System (Cont’d)
Installing Pedestal Assembly
1. Remove screws on adapter and slide pedestal over
adapter on bottom of stove. Figure 22.1.
2. Line up holes in sides of pedestal with holes in adapter.
3. Securely tighten pedestal into place.
Grate
4. Carefully stand stove up and place in desired location.
5. Slip wooden decorative strips onto pedestal edges.
ARS
Channel
Finishing the ARS Installation
1. The ARS channel is already installed on the stove. Set
the grate into the ARS channel and secure with 2
bolts previously removed. Replace the 2 front cut
bricks. Figure 22.2.
Replace both bricks
back into firebox
2. Install the ash drawer.
3. Check to make sure baffle boards and ceramic blanket
are in their proper locations (see page 28).
Figure 22.2
NOTE: If installing a floor installation of an outside air kit on a
Step Top model with a pedestal assembly you must attach
the enclosed cover plate to the back of the stove. Other
wise you may discard this piece. See Figure 22.3.
Adapters
Cover
Plate
Ash Removel
Drawer
Figure 22.3
Oak
Pedestal
Trim
Figure 22.1
Page 22
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
B. Leg Kit and Ash Removal Installation
(ARS) for Step Top Uni-Body
NOTE: The Ash Removal System, must be
installed first before installing the legs.
Begin installing the ARS System.
1. Follow steps 1 through 6 on page 21.
Lay stove flat on its
back on protective
padding or pallet
Ash Drawer
Installing Leg Kit
1. Remove leg mounting brackets packaged inside firebox.
2. Attach the 2 bottom screws of the mounting brackets to the
bottom of the stove with 1/4”-20 Phillips screws. These screws
are located in the component pack. Leave the bottom 2 screws
loose so you can slide the ash pan assembly bottom slots over
the screw heads. This allows the weight of the ash pan to
rest on the screws while you are attaching the top 2 screws.
Once the ash pan is attached, tighten all screws.
Insert 2 bottom
screws loosely
Leg Brackets
Figure 23.2
3. Loosely assemble bolts into the corner of the mounting brack-
ets for leg attachment.
4. Slide legs onto mounting brackets and tighten. Make sure the
legs are up against the bracket. There are leveling bolts in 2
legs. These leveling legs should be in opposite corners.
CAUTION
Do NOT tilt the unit on the cast iron legs.
•
•
Tilting could lead to property damage.
5. Carefully stand stove up and place in desired location. Do NOT
tilt up on the cast iron legs, it could damage the legs.
Lift the unit upright and place it into position on the
floor protector.
6. Use leveling bolts on legs to stabilize and level stove.
Finishing the ARS Installation
1. Follow steps 1 through 3 on page 22. See also Figure 22.2.
Leg Mounting Brackets are
packaged inside firebox.
Leveling Legs at
opposite corners
Figure 23.1
Page 23
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Door Handle Assembly
D. Adjusting The Blower Speed Control
The blower speed control for this unit is adjusted at the factory,
and normally does not require further adjustment.
1. Install washer on door handle shaft.
2. Slide door handle through door.
3. Install second washer(s) as shown.
4. Install key in groove.
N
OTE: When the speed control is turned clockwise,
it will click on to high speed. Continue to turn the
speed control clockwise to decrease the speed. At
full clockwise, the blower should blow gently, but
should not stop.
5. Align groove in latch cam with key; slide latch cam
over shaft
1. With the appliance plugged in, turn the speed
control knob to slow (full clockwise).
6. Install locknut but do not overtighten as the door
handle needs to move smoothly.
2. With a small screwdriver, adjust the blower speed
by turning the adjustment mechanism through the
hole on the side of the speed control.
7. Install spring handle turning in a counter-clockwise
motion to desired location on door handle rod.
3. Adjust the speed so the blower runs slowly, but
does not stop. Turn clockwise to slow the blower
and counterclockwise to increase the speed.
CAUTION
•
•
Do NOT overtighten lock nut.
Door handle needs to move smoothly.
Door Cross Section
(example)
Latch Cam
Locknut
Spring
Handle
Door Handle
Spacing
Washers
Square Key
Figure 24.1
Page 24
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Operating Instructions
8
WARNING
Fire Risk
A. Fire Safety
To provide reasonable fire safety, the following should be
given serious consideration:
Do NOT store wood:
•
Closer than required clearances to com-
bustibles to appliance
Within space required for loading or ash
removal.
1. Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
•
Do NOT operate appliance:
•
•
With appliance door open.
With ash removal system door open.
2. A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
WARNING
Fire Risk.
3. A practiced evacuation plan, consisting of at least two
escape routes.
•
•
•
Do NOT burn wet or green wood.
Store wood in dry location.
Stack wood so both ends are exposed to air.
4. A plan to deal with a chimney fire as follows:
Wet, unseasoned wood can cause accumulation of
creosote.
In the event of a chimney fire:
a. Notify fire department
b. Prepare occupants for immediate evacuation.
c. Close all openings into the stove.
d. While awaiting fire department, watch for ignition
of adjacent combustibles from overheated stove
pipe, hot embers or sparks from the chimney.
C. Burning Process
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order to
improve the situation, we at Quadra-Fire have developed
cleaner-burning woodstoves that surpass the requirements
for emissions established by our governing agencies. These
woodstoves, like any other appliances, must be properly
operated in order to insure that they perform the way they are
designed to perform. Improper operation can turn most any
wood stove into a smoldering environmental hazard.
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover, out
of the rain and snow. Dry and well-seasoned wood will not
only minimize the chance of creosote formation, but will give
you the most efficient fire. Even dry wood contains at least
15% moisture by weight, and should be burned hot enough
to keep the chimney hot for as long as it takes to dry the
wood out - about one hour. It is a waste of energy to burn
unseasoned wood of any kind.
1. Kindling or First Stage
It helps to know a little about the actual process of burning in
order to understand what goes on inside a stove. The first
stage of burning is called the kindling stage. In this stage, the
wood is heated to a temperature high enough to evaporate the
moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat from
the coals and tends to cool the appliance.
Dead wood lying on the forest floor should be considered wet,
and requires full seasoning time. Standing dead wood can
be considered to be about 2/3 seasoned. To tell if wood is
dry enough to burn, check the ends of the logs. If there are
cracks radiating in all directions from the center, it is dry. If
your wood sizzles in the fire, even though the surface is dry,
it may not be fully cured.
Fire requires three things to burn - fuel, air and heat. So, if
heat is robbed from the appliance during the drying stage,
the new load of wood has reduced the chances for a good
clean burn. For this reason, it is always best to burn dry,
seasoned firewood. When the wood isn’t dry, you must
open the air controls and burn at a high burn setting for a
longer time to start it burning. The heat generated from the
fire should be warming your home and establishing the flue
draft, not evaporating the moisture out of wet, unseasoned
wood, resulting in wasted heat.
Splitting wood before it is stored reduces drying time. Wood
should be stacked so that both ends of each piece are
exposed to air, since more drying occurs through the cut ends
than the sides. This is true even with wood that has been
split. Store wood under cover, such as in a shed, or covered
with a tarp, plastic, tar paper, sheets of scrap plywood, etc.,
as uncovered wood can absorb water from rain or snow,
delaying the seasoning process.
Page 25
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
2. Second Stage
The second function of the Start-Up Air Control is operation
of the rear air system. The rear air is used primarily during
a High Burn Rate. However, in some instances rear air is
desired during normal operation to help with combustion of
fuel towards the back of the firebox particularly when burning
hardwoods. The rear air is controlled independently from the
ACC system. Slide the Start-UpAir Control between the first
and third marker as indicated on the label to allow rear air to
enter the firebox. Figure 26.1.
The next stage of burning, the secondary stage, is the period
when the wood gives off flammable gases which burn above
the fuel with bright flames. During this stage of burning it is
very important that the flames be maintained and not allowed
to go out. This will ensure the cleanest possible fire. If the
flames tend to go out, it is set too low for your burning condi-
tions. The air control located at the upper right hand corner
is used to adjust for burn rates. This is called the Burn Rate
Air Control. Figure 26.1.
2. Manual Timer Over-Ride
3. Final Stage
If you need to shut the ACC system off before it shuts itself
off after 25 minutes (i.e. overfire situation), reach down to
the bottom right rear corner and pull the lever toward you.
Figure 26t.2.
The final stage of burning is the charcoal stage. This occurs
when the flammable gases have been mostly burned and only
charcoal remains. This is a naturally clean portion of the burn.
The coals burn with hot blue flames.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of heat
needed to dry and rekindle the next load of wood. It is best
to open the Burn Rate Air and Start-Up Air Controls before
reloading. This livens up the coalbed and reduces excessive
emissions (opacity/smoke). Open door slowly so that ash or
smoke does not exit appliance through opening. You should
also break up any large chunks and distribute the coals so
that the new wood is laid on hot coals.
HIGH
Burn Rate
Air Control
MED
LOW
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To do
this we need to learn to burn our stoves in the cleanest way
possible. Doing this will allow us to continue using our wood
stoves for many years to come.
D. Automatic Combustion Control (ACC)
Start-Up
Typically, when you build a fire, you open the air controls fully
and monitor the fire to prevent it from going into an overfire
situation and/or burning your wood up too quickly before you
shut down the air controls to the desired burn rate. With the
Automatic Combustion Control (ACC) system, you do not
have to continually monitor the fire. Once you set the ACC
system it will control the fire for you. Follow the instructions
below to learn how to operate your stove with ease.
Air Control
Figure 26.1
E. Air Controls
1. Start-Up Air Control
The Start-Up Air Control has two primary functions. The
first function is to activate the Automatic Combustion Control
system (ACC). This function is performed by sliding the con-
trol all the way back until it stops at the “HI” indicator on the
label and then pulling forward to the front of the stove until
it stops. This activates the ACC system and opens the front
air channel and allows air to enter the front of the stove for
approximately 25 minutes. The front air channel gradually
shuts down until it is completely closed at the end of the 25
minutes. The fire is now controlled by the air supplied by the
Burn Rate Air Control. This function should be performed
each time you reload the stove. Figure 25.1.
Manual
Timer (ACC)
Shut Down
Pull Forward
to Shut Down
Figure 26.2
Page 26
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
2. Burn Rate Air Control
4. Medium-Low Burn Rate* - 10,000 to 15,000 BTU/hr
This air supply enters at the upper front of the firebox, near the
top of the glass door. This preheated air supplies the neces-
sary fresh oxygen to mix with the unburned gases, helping
to create second, third and fourth combustions. This air is
regulated by the Burn RateAir Control. There are four settings
High, Medium-High, Medium-Low and Low. When the control
is raised all the way up it is on the High setting and when
pushed all the down it is on the Low setting. Figure 27.1.
Raise the Burn Rate Air Control up to the bottom of
the middle marker and stop. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and
then pull forward until it stops. This activates the timer
system (ACC).
5. Low Burn Rate* - Below 10,000 BTU/hr
Leave the Burn RateAir Control at the bottom marker.
Slide the Start-Up Air Control all the way back until it
stops (HI marker) and then pull forward until it stops.
This activates the timer system (ACC).
F. Burn Rates and Operating Efficiency
For maximum operating efficiency
HIGH
1. This appliance has a timer system (ACC) that operates
the stove at its maximum efficiency removing any guess
work for the homeowner. Follow the instructions below
for each burn rate for the Start-Up Air Control and Burn
Rate Air Control. Figure 27.1.
Shown with Side
Shield Removed
LOW
2. Burn dry, well-seasoned wood.
Low (Closed)
High (Open)
Burn Rates
1. Starting a Fire and Reloading
Open both controls fully by raising the Burn Rate Air
Control all the way up until it stops and slide the Start-up
Air Control back until it stops. After loading the stove with
wood and starting the fire, set both controls to the desired
setting by following the burn rate instructions below.
Burn Rate
Air Control
Front Air Channel
Operated by Timer
Timer
NOTE: These are approximate settings, and will vary with
type of wood or chimney draft. Due to altitude and other
environmental circumstances, this operational information is
a guideline only.
Start-Up Air
Control
RearAir Channel
Operates independently
from Timer
Timer Manual
Shut-off
2. High Burn Rate - Maximum Heat
Raise the Burn RateAir Control all the way up until it stops
(top marker) to a fully open position. Slide the Start-UpAir
Control all the way back until it stops (HI marker) and leave
it there. This setting over-rides the timer system (ACC) so
you must monitor the fire closely while in this setting.
START-UP
HI
REARAIR
WARNING
Risk of Fire.
When set on High Burn Rate and over-riding
the Automatic Combustion Control system an
overfire situation can occur and may result in a
chimney fire.
“HI” setting
over-rides
Timer
Wide
Open
Closed
After activating the timer (ACC), if the control is placed
within the rear air section on the label it will allow rear air
to enter the firebox. This will not interfere with the timer
gradually closing the front air channel in 25 minutes. If
control is set on “HI” it over-rides the timer (ACC).
Overfiring will void the stove warranty.
3. Medium-High Burn Rate* - 15,000 to 30,000 BTU/hr
Raise the Burn Rate Air Control all the way up until it
stops (top marker) to a fully open position. Slide the
Start-Up Air Control all the way back until it stops (HI
marker) and then pull forward until it stops. This activates
the timer system (ACC).
Figure 27.1
NOTE: Operate appliance on High Burn 15 minutes a
day to help keep flue/chimney clean.
Page 27
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
G. Building A Fire
Baffle Board even with front
tube & resting on all tubes
Before lighting your first fire in the stove:
1. Confirm the baffle is correctly positioned. It should be
even with the front tube and resting on all tubes. Figure
28.1.
2. Follow instructions on page 32 for cleaning plated sur-
Burn Rate
Air Control
faces, if applicable.
3. Remove all labels from glass.
Start-Up
Air
Control
There are many ways to build a fire. The basic principle
is to light easily-ignitable tinder or paper, which ignites the
fast burning kindling, which in turn ignites the slow-burning
firewood. Here is one method that works well:
1. Open the Burn Rate Air and Start-Up Air Controls fully.
2. Place several wads of crushed paper on the firebox floor.
Heating the flue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
Ceramic Blanket on Top
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles are in
the immediate area of the appliance. Be sure the room
is adequately ventilated and the flue unobstructed.
5. Light the paper in the appliance. NEVER light or rekindle
fire with kerosene, gasoline, or charcoal lighter fluid; the
results can be fatal.
Tube Channels
Figure 28.1
2 pc Baffle Board
6. Once the kindling is burning quickly, add several full-
length logs 3 inches (76mm) or 4 inches (102mm) in
diameter. Be careful not to smother the fire. Stack the
pieces of wood carefully; near enough to keep each
other hot, but far enough away from each other to allow
adequate air flow between them.
7. Set the Burn Rate Air Control and activate the timer
system (ACC).
8. When ready to reload, It is best to fully open both the
Burn Rate Air and Start-up Air Controls before reload-
ing. This livens up the coalbed and reduces excessive
emissions (opacity/smoke). Open door slowly so that
ash or smoke does not exit appliance through opening.
Large logs burn slowly, holding a fire longer. Small logs
burn fast and hot, giving quick heat.
9. As long as there are hot coals, repeating steps 6
through 8 will maintain a continuous fire throughout the
season.
NOTE:
•
•
Build fire on brick firebox floor.
Do NOT use grates, andirons or other methods to support
fuel.
It will adversely affect emissions.
Page 28
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
I. Opacity (Smoke)
H. Blower Operating Instructions
This is the measure of how cleanly your appliance is burn-
ing. Opacity is measured in percent; 100% opacity is when
an object is totally obscured by the smoke column from a
chimney, and 0% opacity means that no smoke column can
be seen. As you become familiar with your appliance, you
should periodically check the opacity. This will allow you to
know how to burn as nearly smoke-free as possible (goal of
0% opacity).
NOTE: If your Quadra-Fire wood stove is equipped with an
optional blower, you should follow these guidelines:
1. Initial (cold) start-up and all Burn Settings
The blower can be plugged in and turned on right away.
The blower fan is turned on and off by a snap disc.
When your stove has reached a certain temperature
the blower will turn on and when your stove has cooled
down to a certain temperature it will turn off.
J. Overfiring
NOTE: The blower can still be left on at all burn rates
even if you have deactivated the snap disc with the
manual over-ride knob. See page 15.
Do not overfire. Using flammable liquids or too much wood,
burning trash in the appliance, or allowing too much air into
the fire may result in overfiring. If the chimney connector
(stove pipe) or appliance glows red or even worse, white, it is
overfired. This condition may ignite creosote in the chimney,
which can be dangerous, possibly causing a house fire. If
you overfire, immediately close the air controls and door,
if open, to reduce the air supply to the fire. Overfiring will
void the stove warranty.
2. The blower is equipped with a speed control. Adjust
the fan speed by turning the speed control clockwise
to “Low” or counterclockwise to “High”.
3. Snap Disc Location
If you find the blower coming on and off at undesirable
temperatures, relocate the snap disc to another location
in the designated zone on the back of the appliance.
Figure 29.1 There is a manual over-ride switch to
deactivate the snap disc, if necessary. See page 15.
WARNING
Fire Risk.
• Do NOT burn garbage or flammable fluids
such as gasoline, naptha or engine oil.
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monooxide if burn material other
than wood.
May result in illness or possible death.
WARNING
Fire Risk.
Figure 29.1
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
•
•
Do NOT store flammable materials in the appliance’s
vicinity.
Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids to start or “freshen up” a
fire in this heater.
CAUTION
Odors and vapors released during initial operation.
•
•
Keep all such liquids well away from the heater while it
is in use.
•
•
Curing of high temperature paint.
Open windows for air circulation.
Combustible materials may ignite.
Odors may be irritating to sensitive individuals.
Page 29
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
K. Frequently Asked Questions
ISSUES
SOLUTIONS
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Whirring sound
If the optional blower has been installed, the blower produces a whirring sound which
increases in volume as the speed is increased.
Page 30
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Maintaining & Servicing Your Appliance
9
3. ARS Operating and Cleaning
A. General Maintenance
1. Creosote (Chimney) Cleaning
•
•
•
Frequency: As necessary
By: Homeowner
Task: See the following instructions.
•
Frequency: Annually before lighting stove or once every 2
months during heating season.
•
•
By: Homeowner / Chimney Sweep
Task: See the following instructions.
CAUTION
Remove all ash from the firebox and extinguish all hot
embers before disposal. Allow the appliance to cool
completely. Disconnect flue pipe or remove baffle and
ceramic blanket from appliance before cleaning chimney.
Otherwise residue can pile up on top of the baffle and
ceramic blanket and the appliance will not work properly.
(See Baffle Removal on page 34). Close the door tightly.
The creosote or soot should be removed with a brush
specifically designed for the type of chimney in use. Clean
out fallen ashes from the firebox. A chimney sweep can
perform this service.
Injury Risk.
•
•
Gloves recommended
May have sharp edges
1. The stove and ashes must be completely cooled down
before using the Ash Removal System. Reach down and
locate the ash removal door handle under the left side of
the stove in the center. Squeeze the handle and push all
the way back. Amagnet will hold the handle in place which
in turn holds the ash door open.
2. Clean ash down through the ash removal system grate into
the drawer below. If there are large pieces in the ashes,
you can remove the grate before brushing the ash into the
drawer. Be sure to replace the grate before operating the
stove. Remember to leave 1/4 to 1/2 inch (6-13mm) of
ash on the firebox floor to act as a natural grate, allowing
air to flow freely underneath wood.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build
creosote deposits quicker, so it is important to check the
chimney from the top as well as from the bottom.
3. Close the door handle, you will hear a “click” when it closes.
The ash drawer will not pull out if the door handle is left in
the open position. Wear gloves to remove the drawer.
Dispose of the ashes following the directions below.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which
combine with expelled moisture to form creosote. The
creosote vapors condense in the relatively cool chimney
flue of a newly-started or a slow-burning fire. As a result,
creosote residue accumulates on the flue lining. When
ignited, this creosote creates an extremely hot fire which
may damage the chimney or even destroy the house. The
chimney connector and chimney should be inspected once
every 2 months during the heating season to determine if a
creosote or soot buildup has occurred. If creosote or soot
has accumulated, it should be removed to reduce the risk
of a chimney fire.
3. Disposal of Ashes
•
•
•
Frequency: As necessary
By: Homeowner
Task: See the following instructions.
Ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil
or otherwise locally dispersed, they should be retained
in the closed container until all cinders have thoroughly
cooled.
WARNING
Fire Risk.
Prevent creosote buildup.
Inspect chimney connector and chimney once
every two months during heating season.
WARNING
• Remove creosote to reduce risk of chimney fire.
• Ignited creosote is extremely HOT.
Fire Risk.
Disposal of Ashes
•
•
•
Ashes should be placed in metal container with tight
fitting lid.
Do not place metal container on combustible
surface.
Ashes should be retained in closed container until all
cinders have thoroughly cooled.
WARNING
Fire Risk.
•
Do not use chimney cleaners or flame colo-
rants in your appliance.
Will corrode pipe.
Page 31
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
B. Glass Replacement
4. Glass Cleaning
1. Ensure that the fire is out and the appliance is cool
•
•
•
Frequency: As necessary
By: Homeowner
Task: See the following instructions.
to the touch.
2. Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent
injury.
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed
by using a damp cloth dipped in wood ashes or by using
a commercially available oven cleaner. After using an
oven cleaner, it is advisable to remove any residue with
a glass cleaner or soap and water. Oven cleaner left on
during the next firing can permanently stain the glass
and damage the finish on plated metal surfaces.
3. Remove the door with the broken glass by lifting the
door up and off of the hinges.
4. Lay door face down on a table or counter making sure
the handle hangs over the edge so the door lays flat,
on a soft surface.
5. Remove the screws from each glass retainer and
remove the glass. (If screws are difficult to remove,
soak with penetrating oil first).
Aportion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes”
the glass, helping to keep smoke from adhering to its surface.
When operated at a low burn rate, less air will be flowing
over the glass and the smokey, relatively cool condition of a
low fire will cause the glass to become coated. Operating
the appliance with the Burn Rate Air Control and Start-Up Air
Control all the way open for 15-20 minutes should remove
the built up coating.
6. Center the glass with edges evenly overlapping the
opening in the door, (i.e. same space top and bottom,
left and right sides).
7. Replace the glass retainers. Be careful not to cross
thread the screws.
8. Tighten each retainer just a few turns until each is
secured. Check again for centering of glass in door
frame. Continue to tighten each retainer alternately,
a few turns at a time, until the glass is secure. DO
NOT OVERTIGHTEN.
CAUTION
9. Replace the door on the appliance.
Handle glass assembly with care.
Quadra-Fire stoves are equipped with ceramic super
heat-resistant glass, which can only be broken by impact
or misuse. Do not slam stove door or impact the glass.
When closing door, make sure that logs do not protrude
against the glass. Inspect glass regularly. If you find a
crack or break, immediately put the fire out and return
the door to your dealer for replacement of glass before
further use.
Glass
Assembly
When cleaning glass:
•
Avoid striking, scratching or
slamming glass.
•
Do NOT clean glass when hot.
•
•
•
•
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Use commerical oven cleaner on heavier deposits.
Remove all residue of oven cleaner or will permanently
stain glass on next firing.
•
WARNING
Refer to maintenance instructions.
Handle glass with care.
•
Inspect the gasket to ensure it is
undamaged.
5. Cleaning Plated Surfaces
Glass
Assembly
•
•
•
Frequency: As necessary
By: Homeowner
Task: See the following instructions.
•
•
Do NOT strike, slam or scratch glass.
Do NOT operate appliance with glass
& door assembly removed.
Clean all the fingerprints and oils from plated surfaces
BEFORE firing the appliance for the first time. If not
cleaned properly before lighting your first fire, the oils
can cause permanent markings on the plating. After the
plating is cured, the oils will not affect the finish and little
maintenance is required. Wipe clean as needed.
•
Do NOT operate with glass cracked, broken or scratched.
WARNING
Fire Risk.
Injury Risk.
CAUTION
Do not use polishes with abrasives.
•
•
Use only glass specified in manual.
•
DO NOT REPLACE with any other material.
It will scratch plated surfaces.
Glass breakage will occur.
Page 32
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Firebrick Replacement
Replace the firebrick if they become crumbly and/or if there
is a 1/4 inch (6.35mm) gap between the bricks.
1
1
The firebox is lined with high quality firebrick, which has
exceptional insulating properties. There is no need to use a
grate; simply build a fire on the firebox floor. Do not operate
appliance without firebrick.
1
1
1
1
1
1
1. After the coals have completely cooled, remove all old
No brick, ARS
Grate Location
4
4
brick and ash from unit and vacuum firebox.
1
1
2. Remove new brick set from box and lay out to diagram
shown.
5
2
2
2
2
3
3. Lay bottom bricks in unit.
4. Install rear bricks on the top of the bottom bricks. Slide
top of bricks under clip on back of firebox wall and push
bottom of brick back.
9 in.
5. Install side bricks. Slide top of brick under clips on side
of firebox and push the bottom of the brick until it is flush
with the side of the unit.
1-1/4 in.
1-1/4 in.
4-1/2 in.
2
3
6 in.
2 in.
2 in.
5 in.
8 in.
4
1
1
3 in.
1-1/4 in.
1
1
1
1
1
1
Figure 33.2 - 3100 Step Top Brick Assembly
1
1
1
1
4
2
2
2
2
3
No.
1
Brick Size
9 x 4-1/2 x 1-1/4
Qty
10
4
2
6 x 4-1/2
9 in.
3
9 x 4-1/2 with angle
4-1/2 x 4-1/2 x 1-1/4
9 x 3 with angle
1
1-1/4 in.
1-1/4 in.
4-1/2 in.
2
4
2
3
5
1
6 in.
2 in.
2 in.
5 in.
Use Part 832-0550 when ordering individual brick. Provide brick
dimension or copy this page, mark the desired brick and take it
to your authorized dealer.
8 in.
3 in.
4
1-1/4 in.
Figure 33.1 - 3100 Millennium Brick Assembly
NOTE: The Ash Removal System is only
available for the Step Top Model only and
not for the Millennium Model.
No.
1
Brick Size
9 x 4-1/2 x 1-1/4
Qty
12
4
2
6 x 4-1/2
3
9 x 4-1/2 with angle
9 x 3 with angle
1
4
1
Page 33
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
E. Snap Disc Replacement
D. Baffle Removal
1. Locate the snap disc bracket assembly at the bottom left
1. Remove all ash from the firebox, and extinguish all hot
rear corner of the stove. Figure 34. 3
embers before disposal into a metal container.
2. A magnet holds the bracket to the stove. Pull the bracket
down away from the stove to expose the snap disc.
2. The baffle board has 2 pieces. With the ceramic blanket
still in place, slide one baffle piece over the top of other one
and pull out top piece through the door opening and then
remove bottom baffle piece. Figure 34.1
3. Pull the snap disc and spade connectors up and out of
bracket as shown in Figure 34.4.
3. Remove the ceramic blanket.
4. Using a Phillips head screw driver, remove the 2 screws
from the snap disc and then remove the snap disc from
the spade connectors. Replace with new snap disc and
re-connect to spade connectors.
4. Re-install the baffle pieces one piece at a time. Be sure
the baffle boards are even with the front manifold tube and
is resting on all tubes. Figure 28.1 on page 28.
5. Push the snap disc and spade connectors back inside
bracket and re-attach the bracket to the stove.
5. To re-install the ceramic blanket, it is easier to fold it in
half first. Place on top of baffle board, open up and flatten
and smooth out the blanket. Re-check the baffle board for
correct positioning. Figure 34.2.
Figure 34.1 - Baffle
Snap Disc Location
Figure 34.3
Snap Disc
Magnet
Spade
Connectors
Figure 34.2 - Ceramic Blanket
Figure 34.4
Page 34
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
SERVICE / MAINTENANCE TIP
F. Tube Channel Assembly Replacement
Removing Tube Channel Assembly
In order to replace the tube channel assembly a clear-
ance of 19 inches (483mm) is required on the right side
of stove in order to remove the tubes with the stove in
place. If space is not available, the stove will have to be
disconnected from the chimney to proceed with the tube
replacement.
1. Remove the right side shield by removing 2 screws in the
back using a Phillips head screw driver.
2. Remove 4 screws from channel access cover and remove
cover.
3. Locate 2 channel nuts inside of chamber and remove
using a 7/16 socket wrench. Slide out tube channel
assembly.
NOTE:Soak the bolts with penetrating oil for at least 15 min-
utes before trying to remove them.
Replacing Tube Channel Assembly
1. Slide the tube channel assembly into side of firebox and
insert each tube into the corresponding hole in the tube
channel rack starting with the back hole first.
2. Make sure tube channel assembly is flush against the
side of the stove and secure with channel nuts.
3. Re-install channel cover and side shield.
Channel
Access
Cover
Channel Cover
Screws (4)
Tube Channel Rack
Remove
2 Screws
Channel
Nuts (2)
Tube Channel
Assembly
Side Panel
Figure 35.1
Page 35
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
With proper installation, operation, and maintenance your woodstove
will provide years of trouble-free service. If you do experience a prob-
lem, this troubleshooting guide will assist a qualified service person in
the diagnosis of a problem and the corrective action to be taken.
Troubleshooting
10
1. If I can’t get a good fire going, what am I doing wrong?
Diagnostic Question
Possible Causes of Condition
Solutions
Are the air controls open?
•
•
No draft
Open air controls
No combustion air
Is there enough paper?
Insufficient heat to ignite kindling
Use more paper
Use drier kindling
Is there enough kindling?
Is the kindling dry?
Insufficient heat to ignite fuel
Is there enough or too much wood?
Is it too large?
Is it dry enough?
•
•
•
•
Insufficient heat to establish draft
Insufficient air passage
Insufficient surface area
Ignition temperature high due to
moisture
Use small split wood that is well sea-
soned (split, covered on top minimum 6
months, preferably a year)
Are there adequate air spaces
between fuel pieces?
Insufficient combustion air and
exposed surface area
Arrange kindling and wood for air move-
ment
Is the chimney pre-warmed?
Exposed, cold chimney downdrafting
Use lighted rolled newspaper at flue
opening to start upward air movement
Is there smoke in the house?
•
•
Obstruction in chimney
Downdraft from chimney tem-
perature or from negative house
pressure
•
Have chimney checked if it workd
previously
Pre-warm chimney
Shut off exhaust devices
Open window slightly
•
•
•
Does the kindling wood not ignite?
Condition, amount, arrangement of
kindling and fuel
Use more, drier, well-spaced kindling
and fuel.
Does the kindling ignite, but the fuel
doesn’t?
•
•
Amount of kindling
Condition of fuel
•
•
Use more kindling
Use smaller, dry wood
Does the fuel ignite, but not burn well?
•
•
Draft problem
Condition of fuel
•
Use well-seasoned wood and suf-
ficient amount
•
•
Turn exhaust fans off
Open window slightly
2. I smell smoke in the house after we have had a fire. What is the cause/what can I do?
Diagnostic Question
Possible Causes of Condition
Solutions
Solutions
Is the chimney clean?
No: Creosote odor
Have chimney cleaned
3. I smell smoke in the house during operation. What is causing it?
Diagnostic Question
Possible Causes of Condition
Do fires start and burn well?
No:
No:
•
•
Chimney obstruction
Not enough kindling and/or fuel to
establish draft
Inadequate combustion air
Air controls not open
•
•
•
•
•
Check & clean chimney if needed
Use adequate kindling & fuel
Open air controls
Open window
Check for need for balanced air
make-up (Outside Air)
•
•
Yes:
Competition with exhaust devices
Yes:
•
Do not use exhaust fans during
startup
•
Check for need for balanced air
make-up (Outside Air)
Page 36
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
4. I don’t get enough/any heat. What can I do about it?
Diagnostic Question
How much wood is used for fire?
How well seasoned is the wood?
Possible Causes of Condition
Insufficient fuel
Solutions
Make larger fires
Condition of fuel
Burn seasoned wood: (split, covered
on top minimum 6 months, preferably
a year)
Did you install a blower?
Snap disc may be faulty
Replace snap disc
How much heat ouput do you expect? • Unrealistic expectations
• Heat output too low for square foot-
Replace appliance with one with greater
heat output
age
How are air controls set?
Operational problems
Follow manufacturer’s instructions
5. The wood burns too fast. What can I do?
Diagnostic Question
Possible Causes of Condition
Solutions
What is the condition of the wood?
Extremely dry wood
Mix in less seasoned wood after fire
established
How are air controls set?
Operational problems
Follow manufacturer’s instructions
Page 37
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
Reference Materials
11
Beginning Manufacture Date:
Millennium Model: July, 2006
Step Top Model:
August, 2006
A. Exploded view
Item
44
Description
Part No.
430-1141
48
Cam Latch
31
30
47
31
Door, Cast
430-1173
430-1131
7000-012
46
40
Door Handle
45
43
Glass Replacement
48
Glass Frame Assembly (set) 832-0350
47
Glass Frame Screws
Qty (1) 220-0490
Qty (10) 832-0860
44
30
Hinge Pins
Gold: 832-0250
Nickel: 430-5320
43
46
45
29
Key, Cam Latch
Nut, Locking
430-1151
226-0100
40
Spring Handle, 1/2 inch
Gold: 832-0620
Nickel: 250-8330
41
29
42
42
41
Trim Ring for Door (Trim
Door Assembly only)
Gold: 430-2682
Nickel: 430-5340
Glass Size: 15-1/2” wide x 13-3/8” high
Washer, Spacing
Qty (1) 222-0010
Qty (3) 832-0990
Figure 38.1 - Door, Glass And Door Handle Assembly
Item
6
Description
Part No.
12
Air Control Rod Guide,
Start-Up
7033-210
13
10
11
13
Burn Rate Air Control Assem- 7033-023
bly
9
7
Control Arm Assy, Rear Air
Control Rod, Timer
7033-035
7033-213
7033-022
7033-024
7033-246
8
14
8
15
11
12
Door Assembly, Front Air
Door Assembly, Rear Air
Gasket, Front & Rear Air
Timer Doors
7
4
5
Knob, Start-Up Air Control
7000-343
Magnet for Snap Disc Bracket 229-0631
6
15
Snap Disc, F125 F-20
Spring Handle, 1/4 inch
230-0470
14
Gold: 250-0692
Nickel: 250-8340
4
5
10
9
Timer Arm Assembly
Timer Assembly
7033-034
480-1940
Figure 38.2 - Burn Rate Air & Start-Up Air Controls
Page 38
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
22
21
23
24
25
26
27
12
13
10
11
14
9
20
8
19
28
29
18
7
30
15
6
4
5
31
34
16
32
3
33
17
2
1
SIZES
(#33) Baffle Board: 9-1/2” w x 13-3/4” h, each
(#29) Ceramic Blanket: 19” w x 13-3/4” h, 1/2” thick
Millennium Model
Figure 39.1
Item
1
Description
Oak Strip for Pedestal
Pedestal Base
Item
Description
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Panel Assembly, Side, Right
Tube Channel Access Cover (Top)
Tube Channel Assembly
Air Channel, Convection
Bracket, Convection Mount
Air Supply, Back
2
3
Pedestal Riser
4
Knob, Start-Up Air Control
Magnet
5
6
Air Control Rod Guide, Start-Up
Control Arm Assembly, Rear Air
Control Rod, Timer
7
Flue Collar
8
Panel Assembly, Side, Left
Air Channel Assembly, Rear
Brick, Set
9
Timer, Mechanical
10
11
12
13
14
15
16
17
Timer Arm Assembly
Door Assembly, Rear Air
Gasket, Front & Rear Air Doors
Burn Rate Air Control Assembly
Spring Handle, 1/4 inch
Door Assembly, Front Air
Label for Burn Rate Air Control
Label for Start-Up Air Control
Tube Support Rack
Blanket, Ceramic
Hinge Pin
Door Assembly
Spring Handle, 1/2 inch
Baffle Fiberboard, (2 pc)
Brick Retainer
Page 39
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
21
25
39
22
23
26
41
13
11
10
40
14
12
9
8
28
19
20
18
29
5
7
42
15
30
6
38
4
16
17
34
31
33
37
43
32
1
SIZES
36
(#33) Baffle Board: 9-1/2” w x 13-3/4” h, each
(#29) Ceramic Blanket: 19” w x 13-3/4” h, 1/2” thick
35
Step Top Uni-Body Model
Figure 40.1
Item
1
Description
Oak Strip for Pedestal
Knob, Start-Up Air Control
Magnet
Item
23
25
26
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Description
Air Supply, Back
4
Panel Assembly, Side, Left
Air Channel Assembly, Rear
Tube Support Rack
5
6
Air Control Rod Guide, Start-Up
Control Arm Assembly, Rear Air
Control Rod, Timer
7
Blanket, Ceramic
8
Hinge Pin
9
Timer, Mechanical
Door Assembly
10
11
12
13
14
15
16
17
18
19
20
21
22
Timer Arm Assembly
Spring Handle, 1/2 inch
Baffle Fiberboard, (2 pc)
Brick Retainer
Door Assembly, Rear Air
Gasket, Front & Rear Air Doors
Burn Rate Air Control Assembly
Spring Handle, 1/4 inch
Pedestal, Ash Removal System
Legs, Queen Anne
Door Assembly, Front Air
Label for Burn Rate Air Control
Label for Start-Up Air Control
Panel Assembly, Side, Right
Ash Pan, Ash Removal System
Bracket, Leg Mount, Right
Flue Collar
Cover Plate, Ash Removal System
Brick, Set
Tube Channel Access Cover (Top)
Tube Channel Assembly
Cover Mount Plate, Ash Removal System
Bracket, Leg Mount, Left
Air Channel, Convection
Bracket, Convection Mount
Page 40
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
B. Service Parts & Accessories
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on the Quadra-
Fire web site at www.quadrafire.com. When ordering, supply serial and model numbers to ensure correct
service parts.
ITEM #
ACCESSORIES
PART NO.
Blower Assembly
BK-ACC
31
31
31
Door Assembly, Black
Door Assembly, Gold Trim
Door Assembly, Nickel Trim
832-1092
832-1912
DR-31/43NL
LEG-3143-BK
LEG-3143-GD
LEG-3143-NL
OAK-ACC
Leg Kit & Ash Removal System, Cast Legs
Leg Kit & Ash Removal System, Gold Legs
Leg Kit & Ash Removal System, Nickel Legs
Outside Air Kit, Floor & Rear (termination cap, wire ties, flex adapter, fasteners
Outside Air Back Cover Plate & Sealing Rope, (1 inch x 4 ft) Floor Only
Pedestal Assembly & Ash Removal System
see pg 14
SRV7033-041
PED-3143
ITEM #
26
SERVICE PARTS
Air Channel Assembly, Rear
Air Channel, Convection
PART NO.
7033-002
21
7033-144
Air Control Rod Guide, Start-Up Air
Ash Pan, Front Assembly, Leg, Step Top
Ash Pan, Pedestal
7033-210
37
7033-008
7033-010
Ash Pan, Leg, Step Top
7033-050
33
29
Baffle, Fiberboard (2 pieces)
Blower (Motor Only) Replacement
Blanket, Ceramic 1/2” thick, field cut to size, 19” wide x 13-3/4” high
Blower Control Box with Switch
Bracket, Leg Mount, Left & Right (Set), Step Top
Bracket, Snap Disc
SRV7033-209
812-4900
832-3390
7000-194
38,43
SRV7033-183
7033-036
Brick, Individual
832-0550
27
41
Brick, Set, Millennium
SRV7033-006
SRV7033-032
832-3040
Brick, Set, Step-Top
Brick, Uncut, (Set of 6)
13
44
Burn Rate Air Control Assembly
Cam Latch (Door Handle)
7033-033
430-1141
Channel, Ash Removal System
7033-172
Component Pack, Black and Gold, (includes Touch-up Paint, Gold Spring Handles
1/2” and 1/4” (1) each, Trimount Plug, Owner’s Manual, Warranty Card, Consumer
View Card)
7033-027
Component Pack, Nickel (includes Touch-up Paint, Nickel Spring Handles 1/2” and
1/4” (1) each, Trimount Plug, Owner’s Manual, Warranty Card, Consumer View
Card)
7033-029
Component Pack, Step-Top (includes Touch-up Paint, Owner’s Manual, Warranty
Card, Consumer View Card) Spring Handles are included with Door Packaging
7033-043
7033-035
7
Control Arm Assembly, Rear Air
Page 41
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
ITEM #
SERVICE PARTS
PART NO.
Component Pack, Door, Black & Gold (includes Gold Spring Handles 1/2” & 1/4” 1
each, 2 Gold Hinge Pins, Quadra-Fire Logo
436-5350
Component Pack, Door, Nickel (includes Nickel Spring Handles 1/2” & 1/4” 1 each, 2 436-5360
Nickel Hinge Pins, Quadra-Fire Logo
Component Pack, Leg, Step Top (includes Gasket for Ash Removal, Magnet &
Fasteners)
7033-048
Component Pack, Pedestal, Step Top (includes Gasket for Ash Removal, Magnet & 7033-045
Fasteners)
8
Control Rod, Timer
7033-213
7033-120
7033-119
7033-024
7033-022
832-0540
7033-185
832-0460
7033-246
7000-012
832-0350
832-0250
430-5320
430-1151
7000-343
7033-160
7033-166
7033-047
200-3180
200-3240
229-0631
7000-140
226-0100
226-0100/24
33271
42
40
11
15
Cover, Mount Plate, Ash Removal System
Cover Plate, Ash Removal System
Door Assembly, Rear Air
Door Assembly, Front Air
Door Handle Assembly
Gasket, Ash Removal
Gasket, (Tape) Glass, 5 ft
Gasket, Front & Rear Air Timer Doors
Glass Assembly
12
Glass Frame, Set (4 pc)
30
30
46
4
Hinge Pins, Gold (2)
Hinge Pins, Nickel (2)
Key, Cam Latch, (Door Handle)
Knob, Start-Up Air Control
Label for Burn Rate Air Control
Label for Start-Up Air Control
Latch, Handle Assembly, Ash Removal
Logo, Quadra-Fire, Gold
16
17
Logo, Quadra-Fire, Nickel
Magnet for Snap Disc Bracket
Magnet, Round
5
45
45
Nut, Locking (Door Handle)
Nut, Locking (Door Handle) Pkg 24
Outside Air Shield
Paint, Touch-Up, Matte Black
Panel Assembly, Side, Left, Step Top
Panel Assembly, Side, Right, Step Top
Pedestal, Ash Removal System
Pedestal (only) Assembly
Pedestal Base
7000-304
7033-038
7033-037
7033-011
7033-013
7033-163
7033-207
832-1680
Qty (1) 220-0490
25
18
35
2
3
Pedestal Riser
Rope, Door, 3/4” x 84”, field cut to size
Screws, Glass Frame, tabs are not required
47
Qty (10) 832-0860
25
18
Panel Assembly, Side, Left
Panel Assembly, Side, Right
7033-019
7033-017
Page 42
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
ITEM #
SERVICE PARTS
PART NO.
230-0470
7033-261
832-0630
250-8340
832-0620
250-8330
7033-034
480-1940
430-2682
430-5340
832-0560
7033-237
SRV7033-023
7033-148
Snap Disc, F125 F-20
Snap Disc Cover Box
14
14
32
32
10
9
Spring Handle, Burn Rate Control, 1/4”, Gold
Spring Handle, Burn Rate Control,1/4”, Nickel
Spring Handle, Door, 1/2”, Gold
Spring Handle, Door, 1/2”, Nickel
Timer Arm Assembly (ACC)
Timer Replacement (ACC)
42
42
1
Trim Ring, Door, Gold
Trim Ring, Door, Nickel
Trim, Oak Strips for Pedestal (2)
Tube Channel Access Cover (Top)
Tube Channel Assembly (Manifold Tubes)
Tube Support Rack
19
20
28
41
Washer, Spacing (Door Handle)
Qty (1) 222-0010
Qty (10) 832-0990
Wire Harness for Blower & Snap Disc
7033-262
Page 43
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Service And Maintenance Log
Date of Service
Performed By
Description of Service
Page 44
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
D. Homeowner’s Notes
Page 45
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
D. Homeowner’s Notes (Cont’d)
Page 46
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
R
3100 Wood Stove Series (ACC)
C. Warranty Policy
Lifetime Warranty
LIMITED LIFETIME WARRANTY
The Hearth & Home Technologies limited Lifetime Warranty guarantees that the following components will work as designed for the
lifetime of the stove or Hearth & Home Technologies will repair or replace them. These items include but are not limited to steel and
cast iron components, all gas burners, gas logs, combustion chambers, heat exchanger systems, stainless steel firebox components,
plating, doors, glass damaged by thermal breakage, steel baffle supports, steel and ceramic baffles and manifold tubes. Labor is for
the first five years.
THREE YEAR WARRANTY
Our EZ Clean firepots are covered under Hearth & Home Technologies three-year warranty program. Labor is for 3 years.
TWO YEAR WARRANTY
All electrical components such as but not limited to blowers, wiring, vacuum switches, speed controls, control boxes, thermodisc
switches, pilot assembly, gas valves, thermostats and remotes are covered under Hearth & Home Technologies two-year warranty
program. Effective April, 2005 igniters are also covered under the two year warranty. Labor is for two years.
ONE YEAR WARRANTY
Porcelain and Powder Coat finishes are warranted against manufacturer defects for one year. Labor to repair or replace these parts
is covered for one year, reimbursed per our warranty service fee schedule.
CONDITIONS
This warranty is non-transferable and is made to the original retail purchaser only provided that the purchase was made through
an authorized dealer of Hearth & Home Technologies. It must be installed and operated at all times in accordance with the Installa-
tion and Operating Instructions furnished with this product, as well as any applicable local and national codes. Any alteration, willful
abuse, accident, or misuse of the product shall nullify this warranty.
Labor to repair or replace items covered under the limited Lifetime Warranty will be covered for the first five years per our warranty
service fee reimbursement schedule. Parts covered under the limited Lifetime Warranty will be covered for the lifetime of the appli-
ance up to a maximum of ten (10) years after Hearth & Home Technologies discontinues the model and two (2) years for optional
accessories. Adjustments, regular maintenance, cleaning and temporary repairs do not qualify for a service call fee and will not be
covered. The replacement of consumer replaceable items and installation of upgraded component parts do not quality for a service
call fee, and will not be covered.
This limited Lifetime Warranty does not extend to or include surface finish on the appliance, door gasketing, glass gasketing, glass,
firebrick, pellet logs, kaowool or other ceramic insulating materials. It does not cover installation or operational-related problems such
as overfiring, use of corrosive driftwood, downdrafts or spillage caused by environmental conditions, nearby trees, buildings, hilltops,
mountains, inadequate venting or ventilation, excessive offsets, or negative air pressures caused by mechanical systems such as
furnaces, fans, clothes dryers, etc.
Any installation, construction, transportation, or other related costs or expenses arising from defective part(s), repair, replacement,
etc., will not be covered by this warranty, nor will Hearth & Home Technologies assume responsibility for them. Further, Hearth &
Home Technologies will not be responsible for any incidental, indirect, or consequential damages, except as results in damage to
the interior or exterior of the building in which this appliance is installed. This limited Lifetime Warranty does not apply to the venting
components, hearth components or other accessories used in conjunction with the installation of this product not manufactured by
Hearth & Home Technologies
This warranty is void if the stove has been overfired or operated in atmospheres contaminated by chlorine, fluorine, or other dam-
aging chemicals, the stove is subjected to prolonged periods of dampness or condensation, or there is any damage to the stove or
other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.
Hearth & Home Technologies may, at its discretion, fully discharge all obligations with respect to this warranty by either repairing or
replacing the unit, or refunding the wholesale price of the defective part(s).
This limited Lifetime Warranty is effective on all appliances sold after May 1, 2002 and supersedes any and all warranties currently in
existence.
Policy 250-8620 Rev J
Page 47
March 2, 2007
7033-277C
Download from Www.Somanuals.com. All Manuals Search And Download.
R
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer,
CAUTION
Do NOT discard this manual.
•
•
•
Important operating and maintenance
instructions included.
Read, understand and follow these instruc-
tions for safe installation and operation.
Leave this manual with party responsible
for use and operation.
Your Records for Model:
3100 Wood Stove Series (ACC)
DEALERSHIP WHERE PURCHASED:
SERIAL NUMBER:
DATE PURCHASED:
DATE INSTALLED:
___________________________
___________________________
___________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
DEALER TELEPHONE: ________________________
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534,
5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099,
6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064,
6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408,
2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Page 48
7033-277C
March 2, 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|