NorthAmerica’sBest
MODEL 1100-I HEARTH CLASSIC PELLET INSERT
INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS
CONGRATULATIONS—You are now the proud owner of one of the finest inserts in the world for your home—the QUADRA-
FIRE! Now before installing your insert and building your first fire, record the serial number on the warranty card. The serial
number is located on the safety label on the back wall of the hopper.
PLEASE READ ALL OF THE OWNER’S MANUAL AND SAFETY NOTES
IMPORTANT SAFETY NOTES
1. When installing your insert, particular attention should be paid to fire protection. If this unit is not properly installed, a house fire may
result. For your safety, follow the installation instructions, and contact local building or fire officials about restrictions and installation
inspection required in your area.
2. Read power supply section of component information (page 9) before you plug in the insert.
3. Always unplug the insert before cleaning or servicing.
4. Do not connect the insert to a chimney flue already serving another appliance.
5. Do not connect this heater to any air distribution duct or system.
6. The insert operates with a negative pressure firebox and a positive pressure exhaust. It is imperative that the chimney system be airtight
and installed correctly.
7. Dispose of all ashes in a metal container.
8. Do not burn garbage or flammable fluids such as gasoline, naphtha or engine oil.
9. Do not use chemicals or fluids such as gasoline, lantern fuel, kerosene, or charcoal lighter fluid to start or freshen up a fire in this insert.
10. HOT WHILE IN OPERATION. Keep children, clothing, flammable liquids and furniture away from heater. Contact may cause skin
burns.
11. Comply with all minimum clearances to combustibles as shown on page 5.
12. The Quadra-Fire 1100-I is tested and approved for pelleted biomass fuel only. Burning of any other type of fuel voids your warranty!
13. Aladdin Hearth Products, manufacturer of the 1100-I pellet insert, reserves the right to alter its products, their specifications and/or price
without notice.
ALADDIN HEARTH PRODUCTS, GRANTS NO WARRANTY, IMPLIED OR STATED, FOR THE INSTALLATION OR
MAINTENANCE OF THIS UNIT AND ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
(Revised 3/98)
401 N. Wynne Street
Colville, WA 99114
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page
Safety label ............................................................................................................................................................... 4
Listings and specifications ....................................................................................................................................... 5
Dimensions ............................................................................................................................................................... 5
Minimum opening for masonry and zero clearance ................................................................................................. 5
Installation
Masonry and zero clearance .............................................................................................................................. 6
Minimum clearances to combustible materials when installed as a built-in ..................................................... 6
Direct connect with outside air.......................................................................................................................... 7
Full reline with outside air................................................................................................................................. 7
Direct connect without outside air..................................................................................................................... 7
Installed as a built-in (outside air optional) ....................................................................................................... 7
Floor protection ................................................................................................................................................. 8
Chimney and exhaust connections .................................................................................................................... 8
Mobile home installation ................................................................................................................................... 8
Vent termination requirements ................................................................................................................................. 8
Power supply ............................................................................................................................................................ 9
Thermostat control installation................................................................................................................................. 9
Venting graph............................................................................................................................................................ 10
Feed adjustment instructions .................................................................................................................................... 11
Outside air kit installation instructions..................................................................................................................... 11
Operating instructions .............................................................................................................................................. 12
Cleaning and maintenance........................................................................................................................................ 13
Component information............................................................................................................................................ 15
Troubleshooting ........................................................................................................................................................ 17
Notes ......................................................................................................................................................................... 19
Lifetime warranty ..................................................................................................................................................... 20
Warranty card ........................................................................................................................................................... Insert
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL
(FOUND ON INSIDE OF RIGHT FACE SIDE OF INSERT)
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTINGS AND SPECIFICATIONS
QUADRA-FIRE 1100-I pellet inserts are safety tested and listed with Warnock Hersey International to UL 1482, ULC S627, APFI,
and Oregon Administrative rules 814-23-900 through 814-23-909.
INSTALLATION
FASCIA OR TRIM
MASONRY AND ZERO CLEARANCE
A
B
C
D
E
F
Insert side to combustible
Insert top to mantel
Insert top to face trim
Insert side to face trim
Floor protection/hearth extension
Floor protection to the side of door
2” (50mm)
9” (230mm)
0” (0mm)
0” (0mm)
6” (150mm)
8” (200mm)
Noncombustible material
such as brick, tile, etc.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
WHEN INSTALLED AS A BUILT-IN
A
B
C
D
E
Top of inside shroud
2” (50mm)
2” (50mm)
2” (50mm)
3” (75mm)
2” (50mm)
Sides of inside shroud
Back of inside shroud
Vent pipe to combustible
Insert side to combustible
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
FLOOR PROTECTION
This unit may be installed on combustible flooring, providing there is 1 1/2” (37mm) of air space from the base to
combustible floor, or it is placed on nominal 4” (100mm) hollow concrete blocks or any insulating material with a minimum
R value of 2.5.
CHIMNEY AND EXHAUST CONNECTIONS
1. CHIMNEY AND CONNECTOR: Use 3” (75mm) or 4” (100mm) diameter listed “L” or “PL” venting systems. The insert
can be either vertically or horizontally vented.
2. FIREPLACE INSTALLATION: Stainless steel rigid or flexible pipe.
3. AS A BUILT-IN: Use double-wall pipe with a stainless steel inner liner.
NOTE: All pipes are recommended to be sealed with high temperature RTV silicone.
NOTE: DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENT OF THIS INSERT.
When installing the insert as a built-in, the insert is approved for horizontal exhaust. However, we recommend that the
exhaust be installed vertically for at least eight feet, or above the eaves of the house. This will help draw smoke out of the
insert in the event of a power failure.
MOBILE HOME INSTALLATION
1. An outside air inlet must be provided for combustion air, and be unrestricted while the insert is in use.
2. The combustion air duct system must be made of metal, permit zero clearance to combustible construction, prevent
material from dropping into the inlet or into the area beneath the dwelling, and contain a rodent screen.
3. The insert is to be secured to the mobile home. You may drill a hole through the outer panel and secure it to the wall with
a ¼” x 2” lag bolt or equivalent.
4. Do not install the insert in a sleeping room.
5. The structural integrity of the mobile home floor, walls, and ceiling/roof must be maintained.
6. This insert is to be grounded with #8 copper grounding wire or equivalent, terminated at each end with an N.E.C.
approved grounding device.
7. Refer to clearance to combustibles section (page 6) for measurements to combustibles, and appropriate chimney and
venting systems for your application.
VENT TERMINATION REQUIREMENTS
1. Do not terminate vent in an enclosed or semi-enclosed area such as a carport, garage, attic, crawl space, under a
sundeck or porch, narrow walkway or closely fenced area, or any location that can build up a concentration of fumes
such as a stairwell, covered breezeway, etc.
2. Vent surfaces can get hot enough to cause burns if touched. Noncombustible shielding or guards may be required.
3. Termination must exhaust above air inlet elevation. It is recommended that at least five feet of vertical pipe be installed
when the appliance is vented directly through a wall to create some natural draft, to prevent the possibility of smoke
or odor during appliance shutdown, and to keep exhaust from causing a nuisance or hazard by exposing people or
shrubs to high temperatures. In any case, the safest and preferred venting method is to extend the vent through the
roof.
4. Distance from doors and windows, or gravity or ventilation air inlet into building:
a) Not less than 4’ (1.2m) below;
b) Not less than 4’ (1.2m) horizontally from;
c) Not less than 1’ (305mm) above.
5. Distance from bottom of termination and grade - 12” (305mm) minimum. This is conditional upon the plants and
nature of grade surface. The grade surface must not be a lawn. Distance from bottom of termination to public walkway
- 7’ (2.1m) minimum.
6. Distance to combustible materials - 2’ (510mm) minimum. This includes adjacent buildings, fences, protruding parts
of the structure, roof overhang, plants and shrubs, etc.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY
1. The power can be connected from either the left or right side of the insert. First determine which side is closest to an
electrical outlet.
a) For power from the left, remove the left side panel and locate the power inlet (about 4” [100mm] up from the
floor of the insert (refer to drawings below)). Remove the cover plate and discard, plug the power supply cord in
and reinstall panel.
b) For power from the right, remove the right side panel. The power inlet is on the right side of the junction box,
directly under the thermostat call light and the reset button. Remove the cover plate and discard, plug the power
supply cord in, then be sure that you have connected the thermostat before reinstalling the side panel.
NOTE: Never install the power cord under the insert body or around sharp corners, and always maintain the
power cord’s integrity.
THERMOSTAT INSTALLATION
1. A 24-volt thermostat is required to operate this pellet insert. Some thermostats are equipped with an adjustable heat
anticipator. The amperage draw on this insert is .05 amps, so generally the lowest anticipator setting will work.
2. When mounting the thermostat on a wall, be sure to follow your thermostat installation instructions carefully. The
thermostat should be mounted on an inside wall and not in direct line with the insert’s convection air outlet.
NOTE: Be sure the thermostat is mounted level for accurate readings. If the thermostat is located too close to
the insert, you may need to set the temperature setting slightly higher to maintain the desired temperature in
your home.
3. To connect the thermostat wiring to the insert, you must first remove the right side panel using the 5/32 hex head wrench
provided, and remove the flush mounted screws on the far right side of the insert. The panel can now be lifted out of the
way.
4. There is a four screw terminal block located on the right hand side of the junction box, between the fuse receptacle and the
power cord inlet. The top and bottom screws are the mounting screws for the terminal block. The center two screws are
for the thermostat wires. Attach the red wire to the second screw from the top of the terminal block and the white wire to
the third screw from the top.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
When running vertically with pellet venting, the following chart can be used to determine whether to use 3” or 4” (76mm or
100mm) diameter pipe.
4” (100mm) DIAMETER PIPE ONLY
3” or 4” (76mm or 100mm) DIAMETER PIPE
The table below can help you determine the equivalent feet of pipe used for venting when installing a pellet appliance.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEED ADJUSTMENT INSTRUCTIONS
1) Remove any fuel in the hopper.
2) Loosen set screw.
3) Loosen wing nut.
4) Adjust the fuel feed by pulling the rod back to increase the feed, and sliding it forward to decrease the feed.
5) Tighten the set screw and the wing nut.
NOTE: Adjust fuel after the convection blower has been operating for 5 minutes. The flames should be 4" to 6" (100mm to
152mm) above the firepot after adjustment.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
1. FUEL SIZE AND MATERIAL
Fuel pellets are made from sawdust or wood by-products. If the source material is hardwood, pellets will have a higher mineral
content, creating a heavier ash. Minerals and other noncombustible materials, such as sand, will turn into glass when heated to the
extreme temperatures our firepot reaches. This is what forms clinkers in the bottom of the firepot. Trees from different areas will
vary in mineral content. That is why some fuels produce more clinkers than others. Pellets are manufactured in either 1/4" (6mm)
or 5/16" (8mm) diameter and many varying lengths. Pellet lengths may even vary by lot from the same manufacturer, which is why
the feed rate may need to be adjusted occasionally. We recommend that you buy fuel in multiton lots whenever possible. Buying
large quantities of fuel at once will greatly reduce the number of times the feed adjustments will need to be made. However, we do
recommend trying various brands before purchasing multiton lots, to ensure customer satisfaction.
NOTE: This insert will operate properly with either 1/4” (6mm) or 5/16” (8mm) diameter pellets. However, pellets
exceeding 1 1/4” (32mm) in length can cause missed ignitions.
2. BEFORE YOUR FIRST FIRE.
a. First, make sure your insert has been property installed and that all safety requirements have been met. Pay particular attention
to the fire protection, venting and thermostat installation instructions.
b. Now open the front door of the insert and remove all of the accessories that were placed there for shipment. Remove all labels
that are affixed to the glass.
c. Check the position of the thermocouple and make sure that it protrudes approximately 1" (25mm) into the firepot. It may be
necessary to slide the thermocouple and protection tube into their proper positions. Now close the front door.
NOTE: Thermocouple cover tip must be touching thermocouple tip.
d. You are now ready to load fuel, but first see that all accessories have been removed from the hopper. Now fill the hopper with
pellets.
e. Remember that a working thermostat is required for proper operation of this insert. At this time, set the thermostat to its lowest
setting.
3. START YOUR FIRST FIRE
a. Now plug the insert in. The combustion blower will come on. Even though the thermostat is not calling for heat, the combustion
blower will stay on for approximately 10 minutes. This is normal.
b. Next, adjust the thermostat to its highest setting. The red light next to the reset button on the left side of the insert will come on.
This will indicate that the thermostat is calling for heat.
c. The fuel feed system and the igniter are now turned on. NOTE: The fuel feed system will not run when the front door is
open, or with the combustion blower operating.
d. For your first fire, it will be necessary to press the reset button until pellets are dropping into the firepot. This will fill the feed
system and allow the insert to light.
e. The insert will now continue to run as long as the thermostat is calling for heat Once the insert has ignited, let it burn for
approximately 15 minutes, then set the thermostat to the desired room temperature.
4. GENERAL OPERATION INFORMATION
a. Understand that the insert is like most modern furnaces in that it has only one burn rate, full on. When the thermostat calls for
heat, your insert will automatically light and deliver heat in the most efficient and economical way.
b. Once all of the start-up procedures have been completed, simply set the thermostat to a comfortable setting and enjoy the insert.
But remember, you will have to add pellets. The thermostat’s location will have some effect on the insert’s operation. When the
thermostat is located close to the insert, it may require a slightly higher temperature setting to keep the rest of the house
comfortable. If the thermostat location is upstairs while the insert is downstairs, you will notice higher temperatures near the
insert.
c. During each ignition cycle, it is normal to see some smoke. The smoke will stop once the fire starts.
d. After your insert has been burning for approximately 15 minutes, the convection blowers will automatically turn on. These
blowers transfer heat from your insert into the room, and will continue to run after the thermostat has stopped calling for heat or
until all of the heat has been extracted from the insert.
e. Occasionally, the insert may run out of fuel and shut itself down. If this happens, the red light will be on. To restart the insert, fill
the hopper and press the reset button next to the light. When you press the reset button the red light will go out, and when the
button is released the light will come back on. You should see a fire in about four minutes. If not, press the reset button again.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING AND MAINTENANCE
NOTE: Unplug the insert before performing any cleaning or maintenance
1. FIREPOT
A. It takes very little time to clean the firepot. We recommend that you clean the firepot at least once a week. However, if the fuel you
are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the
firepot. A clinker is formed when dirt or a nonburnable substance is heated to 2000°F (1093°C) and becomes glass-like.
B. To clean the firepot:
1. Wait for insert to be in complete shutdown (exhaust blower off).
2. Pull firepot cleanout rod out, then ride back into the closed position.
3. Open firepot access door and empty ash tray.
NOTE: Do not allow cleanout rod to slam back into closed position. This may damage igniter.
NOTE: NEVER pull rod when insert is operating.
2. FIREBOX ASH REMOVAL
Clean as needed. Make sure there are no hot ashes in the firebox before cleaning. When the insert is cool, remove ash with a
vacuum or small scraper, and place it in a metal or noncombustible container.
NOTE: Embers remain hot for many days. Store container in a safe place away from combustibles.
3. HEAT EXCHANGER MAINTENANCE AND CLEANING
There is one cast finned heat exchanger in this insert. We recommend that this heat exchanger be cleaned at least once for every ton
of fuel burned. BEFORE CLEANING THE HEAT EXCHANGER, THE INSERT MUST BE COLD TO THE TOUCH AND
THE POWER MUST BE DISCONNECTED. The heat exchanger is located on the right side of the insert. To clean the heat
exchanger, open the main door and remove the stainless steel cover. It has one tab at the rear of the cover. The cover must be lifted
approximately 1/2” (13mm) and pulled away from the heat exchanger. Now open the bottom access door. On the right side of the
firepot, there is a metal cover plate with two screws. Turn both screws counterclockwise, until they stop. Then remove cover plate
by grasping the front edge and pulling out. Clean the heat exchanger with a brush or scraper, and vacuum out the ashes through the
lower access hole. Then reinstall the bottom cover plate by sliding it back into place and turning the two screws in a clockwise
direction until tight. Close bottom access door. Reinstall the stainless steel cover inside the firebox and close the main door.
Reconnect power and readjust thermostat to desired temperature.
4. VENTING SYSTEM
The venting system should be inspected and cleaned at least once a year, or more often depending upon the quality of your fuel. If
you are experiencing nuisance shutdowns, check for a clogged exhaust system. If the exhaust is restricted, the vacuum safety
switch will shut the feed motor off (the red light will remain on). You can clean the venting system without removing it from the
insert by opening the small hinged access door, located on top of the exhaust blower housing. Using a small vacuum attachment,
vacuum the exhaust housing.
5. DOOR HANDLE ADJUSTMENT
The door latch is adjusted by removing the nut on the back of the door latch. Remove the latch cam and square key, and add or
subtract a washer to space the cam as needed.
6. BLOWERS
There are three blowers in this insert: an exhaust blower that evacuates the exhaust out of the firebox, and two convection air
blowers that delivers heat into the room. THESE BLOWERS REQUIRE NO LUBRICATION.
A. The exhaust blower is located at the left rear side of the insert. It should be inspected during the annual cleaning of the exhaust
system. The exhaust blower impellers can be inspected periodically by using the exhaust blower cleanout door.
B. The larger convection blower is located on the front left side of the insert, and is accessible by removing the front left panel.
The impeller on this blower should be cleaned at least once a year. You can do this without removing the blower. Simply brush
and vacuum the impeller area.
C. The small convection blower is located at the rear right side of the insert. When the insert is pulled out onto the hearth, it is
accessible through a removable access panel. The impeller on this blower should also be cleaned at least once a year, and can
also be cleaned in place.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DOOR GLASS CLEANING AND REPLACEMENT
A. Be sure the insert is cold before cleaning the glass. To clean the glass, use a damp paper towel or any non-abrasive glass cleaner.
Then use a dry towel to wipe off any streaks that may remain.
B. This glass is 5m thick high temperature heat resistant ceramic glass. DO NOT replace it with any other material.
C. Never slam the door or strike the glass in any way, as this may cause breakage. NOTE: The insert will not operate with
broken or missing glass. If it becomes necessary to replace the glass, replacement glass is available from your nearest
Quadra-Fire dealer.
D. To replace glass:
1. Remove door from insert and lay on a padded flat surface.
2. Remove glass tabs and screws with a Phillips screwdriver by turning screws clockwise.
3. Lift glass frame and glass out of the door frame.
4. Place new glass with fiberglass tape around it into door frame, making sure the Quadra-Fire logo reads correctly to the
outside.
5. Place glass frame pieces over the fiberglass tape on the edges of the glass. Be sure glass is centered in the opening (i.e., same
space top and bottom, left and right).
6. Reinstall screws and glass tabs tightly enough to hold everything in place.
7. Check again for centering of glass in door frame, and tighten all screws securely.
8. READING THE FIRE AND ADJUSTMENT PROCEDURES
A properly adjusted fire has a short active flame pattern that extends out of the firepot 4" to 6" (100mm to 152mm). If the fire has
tall flames with black tails and seems somewhat lazy, the feed rate will need to be reduced. Start adjusting this type of fire by
sliding the feed adjustment plate down about 1/2” (13mm). Within eight minutes your adjustment will have taken effect. If the fire
is still too tall, lower the feed adjustment plate again. If the fire is still lazy and you have reached the end of adjustment for the feed
plate, you will need to increase the combustion air. When the fire is too small and rarely peaks above the top of the firepot, you
will need to increase the feed rate by adjusting the plate upwards. If the feed adjustment plate reaches the end of its travel and the
fire is still low and very active, you will have to close the air adjustment to achieve a proper flame.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT INFORMATION
1. POWER SUPPLY
B. The green light located on the top of the control box notifies
you that the insert has reached a temperature of 200°F
(93°C) in the firepot. If this light is not lit in the first four
minutes of operation, the insert will shut down. Check
the thermocouple.
Check the wall receptacle for 120 volt, 60 Hz (standard current).
Make sure the outlet is grounded and has the correct polarity.
When operating with a generator, be sure you have at least 700
watts of power available for the insert during the start cycle.
C. The red light located to the right of the green light is to
indicate that the insert has reached operating temperature.
If this light does not come on in the first nine minutes of
start-up, the insert will shut down. The insert will not try
to relight again by itself. You must manually push the
reset button to restart the cycle.
D. If you suspect a problem with the control box, disconnect
the power supply from the insert, then remove the control
box and take it to your nearest Quadra-Fire dealer for
testing.
2. FUSE
The fuse is located on the right side of the insert, next to the
power cord. To inspect the fuse, push the fuse holder in and
turn the holder cap counterclockwise, then pull out. Replace
with a standard 7 amp 120 volt fuse, if necessary. If the fuse
continues to blow, contact your local dealer.
3. LIGHT
A. The function of the light is to indicate that the thermostat
is calling for heat.
B. If the thermostat is calling for heat, the insert is burning,
and the light is not on, check the bulb. Replace with a 28
volt AC (#85 lamp) bulb.
NOTE: Do not open the control box. This will void
the warranty. Do not plug in or remove control box
without first unplugging the insert.
9. THERMOCOUPLE
4. RESET BUTTON
A. The thermocouple is located on top of the firepot, inside
the ceramic protection tube. It continually monitors the
temperature of the firepot, and lets the insert know if it’s
operating properly. To inspect the thermocouple, slide the
ceramic protection tube off of the thermocouple. The two
wires should be welded at the end, and not broken.
B. Check the terminal block screws to see if they are tight and
making a good electrical connection (located on the top
of the lower junction box).
C. Upon reinstalling the ceramic cover, be sure the
thermocouple is touching the inside end of the ceramic
tube and that the cover is extending 1” (25mm) into the
firepot.
A. The function of the reset button is to momentarily open the
thermostat circuit, which restarts the system. However,
this will only work when the thermostat is calling for heat
and the red light is on.
B. If the light is on, there is no fire, and there is fuel in the
firepot, push the reset button and wait for ignition. You
should have a fire within five minutes.
C. If the light does not go out when the reset button is pushed,
the button switch may be faulty. Contact your local dealer.
5. VACUUM SWITCH
A. The vacuum switch is located on the left side of the insert,
adjacent to the feed motor. To access, you must remove
the left side panel. This switch turns the feed system on
when vacuum is present in the firebox.
D. The thermocouple sends a millivolt signal to the control
box to obtain the green and red lights for the preset
temperatures
B. If the exhaust or the heat exchanger system is dirty or
plugged, the vacuum switch will keep the feed system from
starting.
C. If the firebox door is open, the vacuum switch will keep
the feed system from starting.
10. SNAP DISC #1 (CONVECTION BLOWER)
The function of this snap disc is to turn the convection
blowers (heated air) on and off as needed.
11. SNAP DISC #2 (THERMOSTAT OVERRIDE)
This snap disc will bypass the thermostat and turn off the insert
if an overheat condition occurs, or if the convection blower
should fail to operate. The insert will go into a normal
shutdown: the combustion blower will run for ten minutes,
then turn off.After the insert cools, the snap disc will
automatically reset itself and the insert will relight.
6. THERMOSTAT
The insert is designed to operate on a 24 volt AC thermostat.
Remove the front cover and check to see that the contact points
are not stuck in either the open or closed position, and that both
wires are property connected to the thermostat.
NOTE: The anticipator should be set on the lowest setting
available. Also, check the wire leads for loose connections.
12. SNAP DISC #3 (BACKBURN PROTECTOR)
If, for any reason, the fire tries to burn back into the feed
system or push exhaust up the feed tube, this snap disc will
shut the entire system off. However, sometimes in shipping
the disc will trip and shut power off to the entire insert. To
reset, unplug the insert from outlet and push in the red reset
button in the center of the snap disc, then plug the insert back
in and try to relight it.
8. CONTROL BOX (BLACK BOX)
A. The control box contains most of the electronics that operate
the insert. When the mounting bracket is removed, the
control box can be lifted away from the junction box. The
control box is not to be opened, as that will void its
warranty. However, the control box comes with two test
lights that show if the thermocouple and control box are
working properly.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
13. BLOWER #1 (SMALL CONVECTION BLOWER)
This blower is located on the right side of the insert. When
the insert is pulled out onto the hearth, the blower is
accessible through a removable access panel. This blower
comes on automatically when snap disc #1 heats up. The
blower’s function is to deliver heat from the insert into the
room.
19. DOOR GASKET
Check the door gasket to see that the door is completely closed
and there are no air leaks. This can be done by closing the door
on a piece of paper and checking that the paper is firmly held in
place. You should have resistance when you try to pull the paper
away.
NOTE: If no resistance is found, the door handle assembly
needs to be adjusted or rope seal needs to be replaced.
14. BLOWER #2 (NEGATIVE DRAFT BLOWER)
This blower creates a negative pressure (vacuum) in the
firebox. It extracts all of the exhaust out of the firebox and
sends it into the venting system. The blower is located on the
left side of the insert. When the insert is pulled out onto the
hearth, the blower is accessible through a removable access
panel.
20. HEAT EXCHANGER
There is one cast heat exchanger mounted on the right side of
the firebox. Refer to cleaning and maintenance section in this
manual for cleaning instructions (page 13).
15. BLOWER #3 (LARGE CONVECTION BLOWER)
This blower is located on the left side of the insert, and is
accessible through the left side panel. It is the larger of the
two convection blowers, and pushes air past the cast heat
exchanger and into the room. This blower, along with blower
#1, will come on within 10-15 minutes of ignition.
16. FEED SYSTEM
The feed system pulls pellets up the feed tube from the hopper,
using a hollow auger spring, and drops them down the feed
chute into the firepot. The feed rate is adjustable; for complete
instructions read the fuel feed system in the cleaning and
maintenance section of this manual. NOTE: The feed motor
will not operate when the front door of the insert is open. If
you are having fuel problems, check the following:
A. Check the ramp in the firepot to see that it is free of fuel or
other materials.
B. Check the set screw on the end of the motor shaft to see that
it is tight and not slipping.
C. Check the electrical power to the motor.
D. Check the vacuum switch hose connections.
17. IGNITER
A. The igniter is located in the chamber at the bottom of the
firepot. It is only on during the ignition cycle, and is
usually on for the first two minutes and not more than
four minutes.
NOTE: The element on the igniter is extremely
brittle. Be very careful in handling it.
B. Check the wire leads to the igniter for loose or bad
connections (ceramic wire nuts).
NOTE: Unplug insert before checking wire nuts.
18. FIREPOT
A. Clean the firepot (see section on cleaning and
maintenance on page 13).
B. Make sure the cleanout plate in the bottom of the firepot is
pushed in all the way.
C. Check the gasket between the firepot and the firebox bottom.
A bad seal will affect the ignition time and the flame height.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUTION: UNPLUG STOVE BEFORE SERVICING
1. PLUG IN INSERT, NO RESPONSE
5. SLOW OR SMOKY START-UP
A. Check the power supply for 120 volts AC.
B. Check the fuse in the junction box (7 amp, 120 volt fuse
AGC-7).
C. Check snap disc #3 (unplug insert before checking). Push
reset on snap disc #3.
A. Clean the firepot. Check the firepot gasket for a good
seal between the firepot and the firebox floor.
B. Check the combustion blower (make sure that it is
starting when the thermostat calls for heat).
C. Visually check the cleanliness of the firebox, the heat
exchangers and the venting system.
D. Control box (consult your dealer).
D. The feed rate may be too high. If necessary, adjust with
the fuel adjustment rod located in the hopper.
E. Due to elevation, the air adjusting plate may need to be
adjusted to get the right air to fuel ratio.
2. CALL LIGHT ON, NO FIRE, NO FUEL IN FIREPOT
A. Check the hopper for fuel, sawdust or bridging of pellets
in the bottom of the hopper. If the hopper is low on fuel,
vacuum can be lost through the hopper.
NOTE: Sometimes there might still be fuel in the
hopper. If so, continue to check the areas below.
B. Make sure that the exhaust blower is operating.
C. Check the venting system for obstructions that might
cause restrictions, which would cause the vacuum safety
switch to shut off the auger.
D. Check the heat exchanger system for high ash content If
buildup is present, clean the heat exchanger system.
E. Push the reset button, and try to light the insert again.
6. STOVE RUNS FOR 10 MINUTES, THEN STOPS
FEEDING FUEL
A. Inspect the thermocouple and the cover.
1. The cover needs to make contact with the end of the
thermocouple.
2. The thermocouple and the cover should extend
approximately 1” (25mm) into the firepot.
3. Push the reset button. The thermocouple test lights
located on the control box will automatically turn on;
when the thermocouple reaches 200°F (93°C) the
GREEN LIGHT comes on, and at 1000°F (538°C)
the RED LIGHT comes on. If they fail to turn on
after the fire starts, the thermocouple may need
replacement.
3. CALL LIGHT ON, NO FIRE, PARTIALLY-BURNED
FUEL IN THE FIREPOT
A. Clean the firepot. Check that the igniter hole is clean and
the cleanout plate is tightly in place.
B. Inspect the thermocouple and cover for the following:
1. The cover needs to be making contact with the end of
the thermocouple.
4. Check the control box (consult dealer).
7. FEED SYSTEM FAILS TO START
A. Make sure that the front door to the firebox is closed tightly.
B. Check to make sure that the exhaust blower is coming on
and working.
2. The thermocouple and the cover should extend
approximately 1”(25mm) into the firepot for accurate
temperature reading.
3. Push the reset button. When the thermocouple reaches
200°F (93°C) the GREEN LIGHT will come on, and
at 1000°F (538°C) the RED LIGHT will come on.
NOTE: If the lights fail to come on after the fire
starts, the thermocouple may be faulty.
C. Check the heat exchanger and the venting system for
obstructions or heavy ash buildup.
D. The vacuum switch hose may be plugged.
1. Pull the hose off and blow through it to make sure it is
clear.
C. If the thermocouple appears good, the control box may be
the problem (consult your dealer).
NOTE: Unplug insert from power outlet first.
E. Downdrafts or poor venting systems that do not follow
manufacturer’s recommendations can also cause this
problem.
4. CALL LIGHT ON, NO FIRE, UNBURNED PELLETS IN
FIREPOT
F. Check the hopper and the feed system for blockage.
A. Clean the firepot (possibly a bridging problem at the ignition
hole, located at the bottom of the firepot).
B. If the fire does not start, push the reset button.
C. Check the igniter to see that it comes on. If it does not turn
on, check the following:
1. Check the connections under the firepot. (Ceramic wire
nuts must be used to withstand the heat produced by
the firepot.)
2. Make sure that the igniter is property installed in the
igniter bracket. It should fit tightly, and be centered in
the igniter hole.
3. Inspect the igniter. Replace if damaged.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. THERMOSTAT WILL NOT START UNIT
A. Check the power to the insert.
14. UNIT BURNING, NO CALL LIGHT
A. Replace light bulb (#85 lamp).
1. Unplug for 10 seconds and then plug back in. The
exhaust blower should come on. If it does, go to C.
B. Check the power supply (plug should be 120 volts, fuse
should be 7 amp, 120 volt [AGC-7]).
C. The thermostat or the thermostat wiring maybe faulty.
1. Disconnect the thermostat wires from the insert.
Make a jumper wire in order to create a manual
bypass to determine if the insert or the thermostat is
faulty.
NOTE: Unplug the insert while hooking up the
jumper wire. Plug the insert back in and the unit
should come on and light. If the unit lights, check
the thermostat and the wires connecting them.
D. Check reset button to make sure current is passing
through it.
E. Snap disc #2 would bypass the thermostat if an overheating
situation occurs. The snap disc should reset itself once it
cools down.
15. STOVE IGNITES THEN GOES OUT, LIGHTS STILL ON
= NUISANCE SHUTDOWN
A. Inspect the thermocouple and the cover.
1. Make sure that the thermocouple end and the cover
make contact.
2. The thermocouple and the cover should extend
approximately 1” (25mm) into the firepot.
3. Push the reset button. When the thermocouple reaches
200°F (93°C) the GREEN LIGHT will come on, and
at 1000° F (538°C) the RED LIGHT will come on.
B. Check the fire height. It should be 4” to 6" (100mm to
153mm) out of the firepot.
1. Too high of a fire will lower the vacuum in the firebox
and the vacuum switch may turn off the feed system,
resulting in total shutdown or feed system shutdown
until vacuum is regained.
NOTE: This may also happen in complicated
venting systems, or at high altitudes. Use the feed
adjustment plate to slow fuel input and reduce
flame height. If this does not help, check the air
adjustment plate.
F. Check the control box (consult dealer).
9. UNIT FAILS TO SHUT OFF
A. Check the thermostat and the thermostat wires.
1. Remove one of the thermostat wires from the insert;
the insert should go into a normal shutdown cycle.
B. Check the control box (consult dealer).
C. Check the junction box (consult dealer).
2. Too low of a fire will let the firepot temperature drop
below 1000°F (538°C) and will turn the insert off.
Increase fuel, check for sawdust and bridging of
pellets.
C. Check the heat exchanger and the venting system for
buildup or restriction (cleanout ash buildup).
D. Check the vacuum switch for proper operation.
1. Make sure that the vacuum hose is not clogged.
2. With normal operation, the vacuum switch should shut
the feed system off when the door is opened, and
restart the feed system when the door is closed again.
10. SMOKE FROM THE CONVECTION AIR OUTLET
A. Check the exhaust blower housing and all venting
connections.
B. Most problems with smoke in the house are the result of a
poor venting system.
11. CONVECTION BLOWERS KEEP RUNNING OR FAIL
TO START
A. Snap disc #1 may need to be replaced.
B. Check the wire connections on snap disc #1 and the
convection blowers to be sure a good connection is being
made.
C. Check the convection blowers.
12. INSERT CYCLES ON AND OFF, THERMOSTAT
ALWAYS ON
A. Check that snap disc #1 is coming on and turning the
convection blowers on. If not, snap disc #2 could be
bypassing the thermostat until the snap disc cools and
resets itself.
13. LARGE FIRE, ASH BUILDUP AND DIRTY GLASS
A. Clean the firepot. Check the firepot gasket for a good seal
between the firepot and firebox surface.
B. Visually check the cleanliness of the firebox, the heat
exchanger and venting system.
C. Reduce the feed rate, if necessary, to maintain a fire height
of about 4" to 6" (100mm to 153mm) above the top of the
firepot.
D. If the above do not help, an air adjustment may be needed.
Open more to increase air to help even the air to fuel ratio.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
NorthAmerica’sBest
lifetime warranty
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in
material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state.
This limited Lifetime Warranty covers items such as but not limited to combustion chambers, heat exchanger systems, stainless steel firebox
components, doors, gold plating, and glass damaged by thermal breakage.
All parts to be replaced must be returned to an authorized Aladdin Hearth Products dealer at purchaser’s expense for inspection and approval by
Aladdin Hearth Products prior to repair or replacement. No repair or replacement costs will be honored without approval of Aladdin Hearth
Products.
This new Quadra-Fire product must be installed by a competent, authorized service contractor. It must be installed and operated at all times in
accordance with the installation and operating instructions contained in this manual, as well as any applicable local and national codes. Any
alteration, willful abuse, accident, or misuse of the product shall void this warranty.
Any installation, construction, transportation, or other related costs or expenses arising from defective part(s), repair, replacement, etc., will not be
covered by this warranty, nor will Aladdin Hearth Products assume responsibility for them. Further, Aladdin Hearth Products will not be responsible
for any incidental, indirect, or consequential damages, except as provided by law.
Our E-Z Clean and ceramic firepots are both covered under Aladdin’s three year warranty program.
All electrical components such as but not limited to blowers, igniters, wiring, vacuum switches, speed controls, control boxes, and thermodisc
switches are covered by Aladdin’s one year warranty program.
Aladdin Hearth Products, will not be responsible for any alteration to the unit which causes sooting that results in damage to the interior or exterior of
the building in which this appliance is installed.
This warranty is void if the insert has been operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals, the insert is
subjected to prolonged periods of dampness or condensation, or there is any damage to the insert or other components due to water or weather damage
which is the result of, but not limited to, improper chimney or venting installation.
This limited Lifetime Warranty does not extend to or include paint, pellet insert logs, door gasketing, glass gasketing, firebrick or other ceramic
insulating materials. It does not cover installation or operational-related problems such as overfiring, downdrafts or spillage caused by environmental
conditions, nearby trees, buildings, hilltops, mountains, inadequate venting or ventilation, excessive offsets, or negative air pressures caused by mechanical
systems such as furnaces, fans, clothes dryers, etc.
This limited Lifetime Warranty does not apply to venting components, hearth components or other accessories used in conjunction with the
installation of this product not manufactured by Aladdin Hearth Products. This limited Lifetime Warranty is effective on all pellet inserts sold after
September 1, 1996, and supersedes any and all warranties currently in existence.
---IMPORTANT---
This warranty is not valid unless the warranty registration card has been property completed in full and returned within 10 days from the date of
purchase.
FOR YOUR RECORDS:
DATE PURCHASED _________________________________________ MODEL # _________________________________________________
AUTHORIZED DEALER _____________________________________ SERIAL # __________________________________________________
Copyright Aladdin Hearth Products, May 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
|