SC281675 MacArthur Blvd., Costa Mesa, CA, 92626 USA
Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834
Loudspeaker Signal Processing Products User Manual
SC28
Two-Input, Eight-Output System Controller for QSC Loudspeakers
*TD-000238-00*
TD-000238-00 rev.C
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations and thank you for your purchase of this professional, loudspeaker signal processing product. To get the most from your
investment, we recommend you review all the information provided in this User Manual.
The SC28 is a two-input, eight-output signal processor intended for use with QSC loudspeakers and QSC power amplifiers. The SC28
provides QSC system-specific signal processing for getting the highest performance and superior sound quality from QSC loudspeakers
integrated with QSC amplifiers.
Two-channels of audio enter the SC28 via locking female XLR connectors. Digital audio conversion is 48 kHz, 24-bit, input and output
with a very low noise floor and wide dynamic range. DSP is 32/40-bit floating point. Four channels of output for each of the two inputs
are provided for controlling up to 3-way systems with subwoofers.
The SC28 provides excellent sound quality, durable construction and simple deployment. Amplifiers are matched to the drivers with
active equalization and precise crossover control. Active loudspeaker protection extends the life of drivers. The SC28 solves many appli-
cation challenges by greatly simplifying the configuration of multi-way loudspeaker systems. SC28 and QSC loudspeakers are the per-
fect solution for public performances, corporate events and private parties demanding flexible and excellent sounding system solutions.
SC28 Features
2
4
3
1
5
7
9
8
6
10
1- Input meters
2- LCD display
3- Output meters
6- Output connectors
7- Input connectors
8- USB port
4- Rotary encoder knob (press-to-select)
5- Power LED
9- IEC inlet
10- Firmware update mode select (recessed)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
There are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare
event that service be required. If service is required and the original packing material is not available, ensure that the unit is ade-
quately protected for shipment (strong box of appropriate size, sufficient packing material to prevent load-shifting or impact damage)
or call QSC’s Technical Services Department for packing material and a carton.
What is included in the carton:
Item
Description
Quantity
1
2
3
4
5
SC28 System Controller
Hardware Manual (this document)
IEC Power Cord 3 x #18 AWG, 2 meters 1
USB cable
System Wiring Reference Card(s)
1
1
1
varies
Mounting
The SC28 can be used in or out of an equipment rack. Rack mounting is optional.
Rack Mounting
Rack mount the SC28 by supporting it from underneath while aligning the mounting holes with the threaded screw holes in the rails;
install all four mounting screws and washers and tighten securely. Ensure use of all four mounting screws in order to minimize the
chance of bending or distorting the rack mount ears. When installing equipment into rack, distribute the units evenly. Otherwise, haz-
ardous conditions could be created by an uneven weight distribution.
Maximum operating ambient temperature is 40°C (104°F). Never restrict airflow through the device vents. Please insure that
the air intake and exhaust vents are unobstructed.
Connections
AC Power Cord
Insert the molded receptacle of the AC power cord into the AC power inlet on the
rear panel of the SC28. Plug the AC line connector into the AC outlet. The power
supply will accept 100-240 Volts AC, 50-60 Hertz. If a different type of IEC power
cord is required than supplied with your SC28, contact QSC’s Technical Services
Department.
The correct AC line voltage is shown under the AC power inlet, on the rear
panel. Connecting to the wrong line voltage may damage the amplifier or
increase the risk of electric shock.
USB Port
On the rear panel, there is a type “B” USB port. This port is for firmware updates
and diagnostic functions. Refer to the Updating Firmware section of this manual for
further information.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Inputs
On the rear panel, there are two female XLR line-level inputs marked INPUTS below
the connectors and designated A and B above the connectors. Connect the line-level
analog audio inputs to these connectors. Input sensitivity can be selected from the
Input connectors
Setup Menu; selections are 1.5 V /6 dBu, 3 V /12 dBu, 9 V 21 dBu, or 18 V /
rms
rms
rms/
rms
27 dBu. These values correspond to the maximum input signal level that can be
applied to the inputs without clipping. The signal's source impedance should be less
than 600 ohms.
We recommend balanced connections be used. Balanced connections will reduce AC
hum and interference, especially with long cable runs. Unbalanced connections may
be suitable for short cables. The input impedance is 11k ohm for balanced connections
or 69k ohm for unbalanced connections.
Audio Outputs
There are two sets of line-level outputs on the rear panel grouped as A OUTPUTS
and B OUTPUTS. Each group has four male XLR connectors numbered 1, 2, 3, and 4.
They are “mapped” with the following general convention:
Output connectors
OUTPUT 1- Subwoofer Output
OUTPUT 2- Low Frequency 1 Output
OUTPUT 3- Low Frequency 2 Output
OUTPUT 4- High Frequency Output
There are two Low Frequency outputs (OUTPUT 2 and OUTPUT 3) to allow for low fre-
quency shading requirements of line arrays when operated in triamp mode. If the shading
network of the loudspeaker is used, OUTPUT 2 is not utilized and the amplifiers are
operated in biamp mode.
Pinout label on rear panel
XLR Connector Pinout
Shown are the pinouts for the XLR connectors. Male connectors shown, pinout is the
same for female connectors. We recommend balanced connections be used. Balanced
connections will reduce AC hum and interference, especially with long cable runs.
Unbalanced connections may be suitable for short cables. The input impedance is 11k
ohm for balanced connections or 69k ohm for unbalanced connections.
Balanced connection pinout
1= shield (ground)
3= minus (-)
2= plus (+)
Unbalanced connection pinout
1= shield (ground)
3= jumper to pin 1
2= plus (+)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
General Information
Use of the SC28 involves adherence to the following to achieve proper operation:
1- Input sensitivity for the SC28 must be set to correspond with expected audio source levels.
2- Crossover type must be selected to correspond with amplifier and loudspeaker setup (Biamp or Triamp)
3- Subwoofer operation must be enabled or disabled. If enabled, subs can be configured as stereo or summed (mono) and sub gain can
be adjusted for more or fewer subwoofers than a typical system.
4- Delay times can be inserted for the subs and/or arrays.
5- Limiting can be selected for loudspeaker protection or clip limiting. Loudspeaker protection setting is recommended.
6- Each output of the SC28 must have the amplifier type/model selected and have the amplifier operating mode selected (stereo/
bridge mono).
7- The “Amp Gain” value must be set to match the actual gain control settings of the amplifiers connected to the outputs. All amplifi-
ers must be set to the same gain values.
8- Adherence to connector pinouts and wiring recommendations must be followed.
9- The SC28 “EQ Menu” selections can then be adjusted to compensate for array size, shape, and environmental factors.
Refer to the SC28 Menu Navigation, System Wiring Reference, and the loudspeaker’s User Manuals for detailed information.
AC Mains
There is no AC power switch on the SC28. To connect AC Mains power to the SC28, insert the IEC molded line cord plug into the IEC
receptacle on the rear panel and plug the AC line cord plug into a properly operating AC outlet. To disconnect the SC28 from the AC
Mains, unplug the AC line cord plug from the AC Mains outlet.
Amplifier Setup
The QSC amplifiers connected to the SC28 must have their power switches in the “on” position. For initial testing, use the lowest use-
ful gain setting until the system is operating as expected. After the system setup has been verified and tested, gain settings may be
adjusted as required.
All amplifiers should have their Gain controls set to identical values. This applies to all amp channels, not just channels on one amp.
IMPORTANT! Amp gain control values must be entered in the amplifier setup menu for proper operation.
Updating Firmware
If a firmware update is required, please visit the QSC website and navigate to the SC28 Firmware Updater page. Download and install
the SC28 Firmware Updater software and follow the instructions provided with the software. The USB port is used for the update and
a cable is supplied with the SC28.
Security Features
The 4-digit passcode is set and enabled via passcode screens in the SC28’s Utility menu. When the passcode is enabled, no menu
access is allowed without the passcode. After 10 minutes of inactivity, the display will automatically revert to the Startup menu and
will prompt the user for the passcode (if enabled). Resetting the passcode: Push in on the rotary encoder knob while the power is
turned on (IEC linecord inserted into IEC inlet).
Channel Link
Channel Linking may be enabled/disabled via the channel link screen in the Utility menu. When Channel Link is enabled (Linked) some
A/B controls become linked and are controlled via a single front-panel screen. When channel Link is disabled (Independent) these con-
trols are adjusted independently via separate front-panel screens. When changing the Channel Link form Independent to Linked, chan-
nel A’s parameters overwrite the channel B’s.
Left/Right Controls that may be linked:
•Sub and Array delays
•Parameters of all user-adjustable filters
•Input mute and sensitivity
•Output mutes
•Sub gain
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
LED metering of both input and output are provided.
Input metering is indicated as relative to 0 dBfs (digital
clipping of the input signal) and output metering is indi-
cated in actual output voltage levels in dBu. Meters are
peak-reading and updated every 50 milliseconds.
Input metering for the SC28- Note digi-
tal clipping will be indicated by ONLY
the top red LED being illuminated.
The lower input metering LEDs will remain illuminated
as successively higher levels are indicated. When 0
dbfs is reached, ONLY the upper red LED will illuminate
(lower LEDs will extinguish). If 0 dBfs is indicated often,
reduce input signal level to the SC28. This will reduce
possibly audible distortion caused by clipping the digital
input of the SC28.
The output meters indicate the actual output voltage
level in dBu (0dBu=0.775Vrms). Most QSC amplifiers
clip/limit at about +4 dBu input level.
Output metering for the SC28- Meters
indicate actual voltage level in dBu
for each output. +4 dBu is maximum
input level for most QSC amplifiers.
LCD Display and Control (Rotary Encoder)
The SC28 has a 2 line X 16 character LCD display. The
display and the push-to-select rotary encoder knob pro-
vide data access and editing capability. The rotary
select/accept knob is active for most displayed items
allowing you to scroll through choices by rotating the
control, and accepting choices (entering) by pushing in
on the control.
The accessible menus and sub menus may appear dif-
ferently than example shown. Software updates may
occasionally improve the interface. On the following
pages are shown the basic navigation flow for the SC28
menu system; Setup, EQ, Gain, and Utility.
Notes:
When editing parameters such as Gain or Filter Fre-
quency, turning the knob more quickly (i.e. “spinning”)
will accelerate the parameter’s change.
LCD display of the SC28- Typical loud-
speaker configuration parameters
shown.
LCD Icon key:
Loudspeaker protection/clip limiting is active
Turning the knob to the right will increment
the current selection
Turning the knob to the left will decrement
the current selection
Pressing knob will enter sub-menu or allow
the current selection to be edited
Control knob (rotary encoder)- Adjust-
able parameters can be changed by
rotating the knob and accepted/
selected by pushing in on the knob.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Preliminary Specification
Dynamic Range (AES-17, -60 dB Method, all sensitivities)
unweighted
A weighted
>104 dB
>107 dB
Distortion (AES-17, 20 Hz-20 kHz, all sensitivities)
+4 dBu
2 dB below clip (max)
<0.006% THD+N
<0.006% THD+N
Crosstalk (20 Hz - 20k Hz)
inter-channel (max)
>75 dB
Input Impedance
Balanced (nominal)
Unbalanced (nominal)
11k ohms
69k ohms
Common-Mode Rejection
20 Hz - 20k Hz (min)
>75 dB
>80 dB
20 Hz - 20k Hz (typ)
Input Sensitivities
1.5 V /6 dBu, 3 V /12 dBu, 9 V 21 dBu, or 18 V /27 dBu
rms rms rms/ rms
Audio Converters
Digital Processing
Mute
24-bit, 48 kHz, in and out
32/40-bit floating-point
infinite attenuation
Throughput Delay
1.4125 milliseconds
Program Inputs
Connector Type
Type
2
XLR female, locking
Electrically balanced
Grounding
Pinout
All shield terminals connected to chassis
1: GND
2: +
3: -
Program Outputs
Connector Type
Type
8
XLR male
Electrically balanced
Grounding
Pinout
All shield terminals connected to chassis
1: GND
2: +
3: -
Controls
Rotary encoder knob with push-to-select function
Indicators
Power
Blue, front panel
LCD Data Display
Input/Output Meters
2 line x 16 character, backlit, front panel
Green, Yellow, Red, front panel
Specifications are subject to change without notice.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Preliminary Specification
USB Port
USB type “B”
USB Cable
1.5 meters long, USB 1.1 compliant
100-240 VAC, 50-60 Hz, no user adjustment required
IEC-type inlet
AC Power Requirements
AC Power Connection
AC Power Cord
2 meters long, #18AWG
Specifications are subject to change without notice.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty (USA only; other countries, see your dealer or distributor)
Disclaimer
QSC Audio Products, LLC is not liable for any damage to amplifiers or any other equipment that is caused
by negligence or improper installation and/or use of this loudspeaker product.
QSC Audio Products 3 Year Limited Warranty
QSC Audio Products, LLC (“QSC”) guarantees its products to be free from defective material and / or
workmanship for a period of three (3) years from date of sale, and will replace defective parts and repair
malfunctioning products under this warranty when the defect occurs under normal installation and use -
provided the unit is returned to our factory or one of our authorized service stations via prepaid transpor-
tation with a copy of proof of purchase (i.e., sales receipt). This warranty provides that the examination
of the return product must indicate, in our judgment, a manufacturing defect. This warranty does not
extend to any product which has been subjected to misuse, neglect, accident, improper installation, or
where the date code has been removed or defaced. QSC shall not be liable for incidental and/or conse-
quential damages. This warranty gives you specific legal rights. This limited warranty is freely transfer-
able during the term of the warranty period.
Customer may have additional rights, which vary from state to state.
In the event that this product was manufactured for export and sale outside of the United States or its
territories, then this limited warranty shall not apply. Removal of the serial number on this product, or
purchase of this product from an unauthorized dealer, will void this limited warranty.
Periodically, this warranty is updated. To obtain the most recent version of QSC’s warranty statement,
1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA
Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834
© Copyright 2007, QSC Audio Products, LLC
QSC® is a registered trademark of QSC Audio Products, LLC
“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office
All trademarks are the property of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|