P Z R 6 0 0
A m p l i f i e r
P Z R 1 0 0 0
A m p l i f i e r
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND CONTROLS
FRONT PANEL, PZR600
Power On/Off
Protection Circuit and Indicator
The indicator will be illuminated when
the amplifier is powered on and at turn-
on delay status; the indicator will be
turned off after internal outputs are
connected. The indicator will also be
illuminated when the amplifier has
abnormal problems, such as overload
or excessive heat.
Channel 1 and Channel 2
Output Level Controls
Lets you adjust the sound levels
for each channel.
Clip Circuit and Indicator
This special circuitry protects
the amplifier and speaker system
from being damaged by
overdriving power levels.
Indicator lights remind the user
to reduce the volume when
amplifier output is excessive.
REAR PANEL, PZR600/ PZR1000
Fan Cooling
Cooling system is automatically activated
whenever amplifier is turned on. This forced
air cooling system rapidly exhausts interior
heat, reducing operating temperature and
aiding performance.
Stereo/Mono Switch
Lets you select conventional
stereo operation with a
stereo input signal or bridged
mono input mode.
Input Jacks
Let you connect a variety of audio
input sources via the balanced
(XLR/6.35mm phone jack
combinations) or unbalanced (RCA)
inputs.
PYLE PRO PZR600/1000 Amplifier Owner’s Manual – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION GUIDELINES
Stereo or Mono Inputs
Your Pyle Pro amplifier can be operated in Stereo, Mono or
Bridged mode, depending on the input source. If the input
signal is mono, slide the Stereo/Mono/Bridged selector
switch to MONO and the signal will be routed through both
channels. If you wish to run the amplifier in bridged output
mode, slide the switch to Bridged.
Connecting the GND (GROUND) screw terminal Connecting
a mixer or preamplifier may cause excessive noise or hum
in the amplifier output. To prevent this, connect one end
of a low-capacitance shield wire to the amplifier's ground
screw (on the rear panel). Then connect the other end of
this wire to the ground terminal on the mixer or preamplifier
enclosure.
Speaker connections
You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to
Channel 1 and/or Channel 2 of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
PREAMP OR MIXER
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
LOW CAPACITANCE SHIELD WIRE
GROUND SCREW
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of the speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
Input connections
These amplifiers accept a board range of input sources,
including Compact Disc (CD,DVD) players; Cassette, Reel-
to-Reel or other tape players; Radio Tuners; Equalizers;
Signal Processors.
NOTE: Use 16-gauge speaker wire for lengths up to25
feet; 14-gauge wire for lengths over 25 feet. It is
recommended that you use the shortest length of wire
possible.
Connecting a CD, DVD, tape player or tuner
In a normal installation, one would use the RCA JACKS for
connecting a CD player, DVD player,tape player or tuner.
2. Connect the speaker wires to the speaker's positive and
negative terminals.
NOTE: Most speaker terminals are either color-coded
or have a mark that indicates the terminal's polarity.
Usually positive terminals are red or have a plus symbol
(+), and negative terminals are black or have a minus
symbol (-).
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
use RCA jacks
CD PLAYER, TAPE PLAYER
OR TUNER
STEREO OPERATION
SWITCH IN “STEREO” POSITION
Connecting an equalizer or external signal processor
Connect the processor's OUT to the amplifier's IN connector.
CH 2
CH 1
EQ OR MIXER
STEREO SIGNAL SOURCE
EQ OR MIXER
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
use XLR/6.35mm combo jacks
2 – PYLE PRO PZR600/1000 Amplifier Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to standard AC power
MONO OPERATION
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
SWITCH IN “MONO” POSITION
Mounting the amplifier
This amplifier is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
CH 2
CH 1
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
Turning the amplifier on
1. Turn on the audio input source equipment which is
connected to the amplifier INPUT jacks.
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
2. Set the amplifier’s Channel 1 and Channel 2 output level
gain controls to the minimum level settings.
3. Push in the power switch to turn the amplifier on.
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
Using the power blue LED meters
The meter pointer position indicates the amplifier output
power. For ease of reading in dark environments, the meter
is illuminated.
Bridged Mode Operation
This amplifier can operate in a mono bridged output mode, if
your speakers can handle the following power output levels:
PZR600: 1000 watts
PZR1000: 2000 watts
Using the Channel 1 and Channel 2 Output Level controls
Rotate output level gain clockwise to increase, or counter-
clockwise to decrease the output power. To get the best
performance with the least sound distortion, always adjust
the output level gain so the meter's pointer does not
continuously exceed the extreme right of the meter's scale.
As shown in the diagram below, connect the speaker's positive
(+) to the amplifier's red speakers left (1/2) terminals and
negative (-) to red speakers right (1/2) terminals.
The speaker right (+) on the amplifier is used as a negative (-)
terminal for a bridged connection.
CAUTION: It is possible to overdrive the amplifier by
setting output level gain too high, which may cause
damage or failure.
NOTE: The extra amplifier output of 6.35mm phone
jacks can not be used for the bridged connection. It can only
be used in normal (non-bridged) operation as a stereo speaker
output.
About the internal clip circuitry
Special clip circuitry incorporated into your Pyle Pro
amplifier’s design protects the amplifier and speaker system
from being damaged from overdriving power.
MONO BRIDGED OPERATION
SWITCH IN “BRIDGED” POSITION
Under normal conditions, the amplifier’s clip indicator will
flicker as the output power momentarily exceeds the level
as set by the output level gain selector.
However, under excessive output conditions, the clip
indicator lights remain on continuously, alerting you that
the special clip circuitry has become active. When this
occurs, you should simply reduce the output power level
by rotating the Master Volume control counterclockwise.
DO NOT USE
BLACK TERMINALS
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
PYLE PRO PZR600/1000 Amplifier Owner’s Manual – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for your Pyle Pro Amplifier
Limited Warranty
Your Pyle Pro Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier gently and carefully - do not drop!
• Keep the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking
new. Do not use harsh chemicals, solvents or
detergents!
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
Resetting the circuit breaker
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
•
•
A copy of your sales receipt or other proof of purchase
A brief letter, indicating the problem you are experiencing with the
product
Include in your letter your return address, daytime phone number and
R.A. number
Also include a check or money order for $15.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Resetting the circuit breaker
•
•
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
Amplifier Specifications
PZR600
PZR1000
Input Impedance, balanced (unbalanced)
Continuous Output Power
20 k-Ohms (10 k-Ohms)
20 k-Ohms (10 k-Ohms)
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
70W x 2
100W x 2
110W x 2
130W x 2
600W x 2
170W x 2
220W x 2
230W x 2
260W x 2
1400W x 2
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
Peak Power, 8 Ohms
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 8 Ohms
140W x 1
140W x 1
1200W x 1
440W x 1
880W x 1
2800W x 1
Peak Power
THD at rated output power
0.1%
10 Hz to 50 kHz
1.0V
0.1%
10 Hz to 50 kHz
1.0V
Frequency Response +/– 3 dB
Input Sensitivity for rated output power
Signal-to-Noise Ratio A-Weighted
100 dB
100 dB
Speaker Impedance
Stereo
Bridged
4-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
Power Requirement
120 VAC, 60 Hz / 230 VAC, 50 Hz
120 VAC, 60 Hz / 230 VAC, 50 Hz
Dimensions H x W x D, inches
(mm)
3 15/32 x 19 x 10 11/16
(88 x 482 x 271)
3 15/32 x 19 x 10 11/16
(88 x 482 x 271)
Weight, lbs (kg)
16.7 (7.6)
20.5 (9.3)
4 – PYLE PRO PZR600/1000 Amplifier Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PYLE PRO PZR600/1000 Amplifier Owner’s Manual - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
All PYLE PRO products are carefully constructed and tested before
shipment. Units purchased in the USA are warranted to be free of
defects in material and workmanship for two (2) years from the date
of purchase. This warranty is limited to the original retail purchaser
of the amplifier.
Should the unit fail due to factory defects in material or workmanship,
your unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return
Hotline at (718) 236-6948 to obtain a Return Authorization Number.
This R.A. # must appear on the outside of your package and on all
paperwork relating to your return.
When returning the unit to us for warranty service, it must be carefully
packed and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing
with the product
• Include in your letter your return address, daytime phone
number and R.A. number
• Also include a check or money order for $15.00 for return
shipping, handling and insurance, or provide your Visa/MC
number with expiration date.
Our obligation under this warranty is limited to the repair or replacement
of the defective unit when it is returned to us prepaid. This warranty
will be considered void if the unit was tampered with, improperly
serviced or subject to misuse, neglect or accidental damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
|