Proxima ASA Projector DP6870 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Liquid Crystal Projector

User's Guide

Thank you for purchasing this liquid crystal projector.

WARNING • Please read the accompanying manual “Safety Instruction"

and this user's guide thoroughly to ensure correct usage through

understanding. After reading, store this instruction manual in a safe place for

future reference.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without

express written authority.

TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of

International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of

Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard

Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the

trademarks and registered trademarks of all companies, even when not mentioned.

CONTENTS

Page

FEATURES .......................................2

TROUBLESHOOTING ....................20

OSD Message ......................................20

Indicators Message ..............................21

Symptom ..............................................22

BEFORE USE ...................................2

Contents of Package ..............................2

Part Names.............................................3

Loading the Batteries..............................5

SPECIFICATIONS...........................23

INSTALLATION ................................6

Installation of the Projector and Screen........6

Angle Adjustment ...................................6

Cabling ...................................................7

Power Connection ..................................8

Example of System Setup ......................8

Plug & Play.............................................8

OPERATIONS...................................9

Power ON ..................................................9

Power OFF ..............................................9

Basic Operation....................................10

Setup Menu ..........................................12

Input Menu............................................13

Image Menu..........................................14

Options Menu .......................................15

No Signal Menu....................................16

MAINTENANCE ..............................17

Lamp.....................................................17

Air Filters ..............................................19

Other Maintenance...............................19

.......................................................................................

TABLES

Table 1. Installation Reference.................6

Table 2. Cabling .......................................7

Table 3. Basic Operation........................10

Table 4. Setup Menu ..............................12

Table 5. Input Menu................................13

Table 6. Image Menu..............................14

Table 7. Options Menu ...........................15

Table 8. No Signal Menu........................16

Table 9. OSD Message ..........................20

Table 10. Indicators Message ................21

Table 11. Symptom ................................22

Table 12. Specifications .........................23

.......................................................................................

For "TECHNICAL" and "REGULATORY

NOTICE", see the end of the manual.

_{Download from Www.Somanuals.com. All Manuals Search And Download.}ENGLISH-1

FEATURES

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /

SECAM video signals onto a screen. Little space is required for installation and large images can

easily be realized.

Outstanding Brightness

The UHB lamp and high-efficiency optical system assure a high level of brightness.

Partial Magnification Function

Interesting parts of images can be magnified for closer viewing.

Distortion Correction Function

Distortion-free images are quickly available.

BEFORE USE

Contents of package

Make sure all of the following items are included in the package. If anything is missing, please

contact your dealer.

NOTE • Keep the original packing material for future reshipment.

Power Cord

(Europe Type)

RGB Cable

Power Cord

(US Type)

Projector

(with Lens Cap)

xxxxxxx

XXXXXX

Component

Video Cable

Video/Audio Cable

(with white lead)

Digital RGB Cable

(with green lead)

User's Guide (this manual)

Safety Instruction

STANDBY/ON

VIDEO

BLANK

RGB

LASER

Quick Start Guide

Product Registration Card

AUTO

KEYSTONE

"Technology

Upgarde Program" Card

Batteries

for Remote Control

Transmitter

Mouse cable

(PS/2)

MENU SELECT

POSITION

RESET

FREEZE

OFF

PinP

MAGNIFY

MUTE

"Thank you" Card

FOCUS ZOOM

VOLUME

Remote Control

Transmitter

ENGLISH-2

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE USE (continued)

Part Names

ZOOM Button

KEYSTONE Button

STANDBY/ON Button

LAMP Indicator

FOCUS Button

ZOOM

FOCUS

INPUT Button

MENU Button

RESET Button

TEMP Indicator

KEYSTONE

INPUT

STANDBY/ON

RESET

LAMP POWER TEMP

POWER Indicator

Control Panel

(Refer to P.9 "OPERATIONS")

Remote Control Sensor

Lens

Control Panel

Ventilation Openings

(exhaust)

Filter Cover

( Air Filter )

Carrying Handle

Foot Adjuster

Lens Cap

Filter cover

Air Filter and Intake

(

)

for the Cooling Fan

Foot Adjuster

Front/Right View

Remote Control Sensor

Speaker

Terminal Panel

(Refer below)

Power Switch

AC Inlet

(to Power Cord)

Rear/Left View

RGB IN 1 Terminal

RGB IN 2 Terminal

DVI

DVI Terminal

S-VIDEO Terminal

VIDEO Terminal

RGB OUT Terminal

RGB IN

S-VIDEO

VIDEO

COMPO

NENT

VIDEO

CONTROL Terminal

RGB OUT

CONTROL

AUDIO(MONO)/L

Terminal

AUDIO IN RGB1/DVI Terminal

AUDIO IN RGB2 Terminal

AUDIO OUT Terminal

(MONO)/L

AUDIO

AUDIO IN

AUDIO

OUT

C^B/PB

CR/PR

RGB

DVI

RGB

USB

AUDIO R Terminal

USB Terminal

COMPONENT VIDEO

Y Terminal

CB/PB Terminal

C^R/PR Terminal

Terminal

Panel

_{Download from Www.Somanuals.com. All Manuals Search And Download.}ENGLISH-3

BEFORE USE (continued)

Part Names (continued)

BLANK Button

STANDBY/ON Button

VIDEO Button

Disk Pad

LASER Button

RGB Button

MOUSE / RIGHT Button

Used to operate the

mouse shift function and

left click function.

Used to click the right

mouse button.

KEYSTONE Button

RESET Button

AUTO Button

MENU Button

Used to click the right

mouse button.

MENU SELECT Button

Used to click the left

mouse button.

PinP Button

FREEZE Button

MUTE Button

Button

Used to operate the

mouse shift function.

VOLUME Button

POSITION Button

MAGNIFY Button

ZOOM Button

FOCUS Button

REMOTE CONTROL TRANSMITTER

(Refer to P.9 "OPERATIONS")

These functions work when the mouse control function is activated. Remember, the POSITION,

BLANK ON and MENU ON functions disable the mouse control function.

WARNING • The laser pointer of the remote control transmitter is used in place of a

finger or rod. Never look directly into the laser beam outlet or point the laser beam at

other people. The laser beam can cause vision problems.

CAUTION • Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

AVOID EXPOSURE-

LASER RADIATION-

LASER RADIATIONS IS

EMITTED FROM THIS

APERTURE

DO NOT STARE INTO BEAM

MAX. OUTPUT: 1mW

WAVE LENGTH 650nm

CLASS2 LASER PRODUCT

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS2 LASER PRODUCT

MAX. OUTPUT: 1mW

WAVE LENGTH: 650nm

IEC60825-1:1993+A1:1997

Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations

pursuant to Laser Notice No.50, dated 2001.7.26

SMK CORPORATION

6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511

MANUFACTURED Novemver 2001

PLACE OF MANUFACTURER:

• Keep the remote control transmitter away from children and pets.

NOTE

• Do not give the remote control transmitter any physical impact. Take care not to drop.

• Do not place the heavy objects on the remote control transmitter.

• Do not wet the remote control transmitter or place it on any wet object.

• Do not place the remote control transmitter close to the cooling fan of the projector.

• Do not disassemble the remote control transmitter.

ENGLISH-4

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE USE (continued)

Loading the Batteries

Install the AA batteries into the remote control

transmitter.

1. Remove the battery cover.

Push the knob while lifting up the battery cover.

2. Load the batteries.

Make sure the plus and minus poles are correctly

oriented.

3. Close the battery cover.

CAUTION • Use only the specified batteries with this remote control

transmitter. Also, do not mix new and old batteries. This could cause battery

cracking or leakage, which could result in fire or personal injury.

• When loading the batteries, make sure the plus and minus terminals are

correctly oriented as indicated in the remote control transmitter. Incorrect

orientation could cause battery cracking or leakage, which could result in

personal injury or pollution of the surrounding environment.

• When you dispose the battery, you should obey the law in the relative area or

country.

• Keep the battery away from children and pets.

• When not to be used for an extended period, remove the batteries from the

remote control transmitter.

NOTE Replace the batteries when remote control transmitter operation becomes difficult.

_{Download from Www.Somanuals.com. All Manuals Search And Download.}ENGLISH-5

INSTALLATION

Installation of the Projector and Screen

Refer to the drawing and table below for determining the screen size and projection distance.

The projection distances shown in the table below

are for full size (1024 x 768 dots).

Screen

a: Distance from the projector to the screen. ( 10%)

b: Distance from the lens center to the bottom of the

screen. ( 10%)

Table 1. Installation Reference

a [inches (m)]

Screen size

[inches (m)]

Top View

[inches (cm)]

Min.

55 (1.4)

Max.

40 (1.0)

60 (1.5)

73 (1.9)

(3)

(4)

(6)

(7)

(9)

85 (2.2) 114 (2.9)

114 (2.9) 151 (3.8)

144 (3.7) 191 (4.9)

176 (4.5) 231 (5.9)

220 (5.6) 282 (7.2)

291 (7.4) 386 (9.8)

80 (2.0)

100 (2.5)

120 (3.0)

150 (3.8)

200 (5.0)

Lens center

4 (11)

6 (15)

Side View

CAUTION • Install the projector in a suitable environment according to instructions of

the accompanying manual “Safety instruction” and this manual.

• When you fix this unit with a metal tool and the like, you must connect it with ground

wire; otherwise, fire or electric shock can result.

Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the

building using an optional three-core power-supply cord.

• Please basically use liquid crystal projector at the horizontal position. If you use liquid

crystal projector by the lens up position, the lens down position and the side up position,

this may cause the heat inside to build up and cause damage. Be especially careful not to

install it with ventilation holes blocked.

• Do not install LCD projector in smoke effected environment. Smoke residue may buildup

on critical parts (i.e.LCD panel, Lens Assy etc.).

Angle Adjustment

Use the foot adjusters on the bottom of the

projector to adjust the projection angle. It is

variable within 0˚ to 9˚ approximately.

1. Lift up the front side of the projector, and

pressing the foot adjuster button, adjust the

projection angle.

Foot Adjusters

2. Release the button to lock at the desired angle.

3. Use the foot adjusters for fine adjustment. Do

not force the adjuster screws. This could

damage the adjusters or cause the lock to fail.

Variable within the range of approximately 0° - 9°

CAUTION • Do not release the foot adjuster button unless the projector is

being held; otherwise, the projector could overturn or fingers could get

caught and cause personal injury.

ENGLISH-6

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

Cabling

Refer to the table below for connecting each terminal of the projector to a device.

Table 2. Cabling

Function

Terminal

Cable

RGB IN 1

RGB IN 2

RGB OUT

Analog RGB input

RGB cable with D-sub 15-pin shrink jack

and inch thread screws

Analog RGB output

Digital RGB input

DVI

DVI cable with inch thread screws

Audio cable with stereo mini jack

AUDIO IN [RGB 1] / [DVI]

(interlocked with RGB IN 1 or DVI)

Audio input

(from the computer)

AUDIO IN [RGB 2]

(interlocked with RGB IN 2)

PS/2 mouse control

ADB mouse control

Serial mouse control

RS-232C communication

USB mouse control

PS/2 mouse cable

ADB mouse cable

Serial mouse cable

RS-232C cable

USB cable

CONTROL

USB

S-video input

Video input

S-VIDEO

S-video cable with mini DIN 4-pin jack

Video/Audio cable

VIDEO

COMPONENT VIDEO Y

COMPONENT VIDEO CB/PB

COMPONENT VIDEO CR/PR

AUDIO (MONO)/L

AUDIO R

Component video input

Component Video cable

Audio input

(from video equipment)

Video/Audio cable or Audio cable with RCA

jack

Audio output

AUDIO OUT

Audio cable with stereo mini jack

CAUTION • Incorrect connecting could result in fire or electrical shock.

Please read this manual and the separate “Safety Instruction”.

• Before connecting, turn off to all devices to be connected, except for the USB

cable.

• The cables may have to be used with the core set to the projector side. Use the

cables which are included with the projector or specified.

NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the

projector is compatible with the device.

• Secure the screws on the connectors and tighten.

• For some RGB input modes, the optional Mac adapter is necessary.

• To select the DVI input, the computer may need some settings. See the manuals of the computer for details.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible

with this projector.

• Refer to the “TECHNICAL” section for the pin assign of connectors and RS-232C communication data.

• When the DVI terminal is used, the RGB OUT terminal may not function.

_{Download from Www.Somanuals.com. All Manuals Search And Download.}ENGLISH-7

INSTALLATION (continued)

Power Connection

Use the correct power cord depending on the power outlet to be used.

Connect the AC inlet of the projector to the power outlet firmly by the power cord.

Power outlet

CAUTION • Be carful in handling the power

cord according to instructions of the

accompanying manual "Safety Instruction"

and this manual.

• Connect the power cord firmly. Avoid using a

loose, unsound outlet or failed contact.

AC Inlet

Power Cord

Example of System Setup

Computer

(desktop type)

Computer

(notebook type)

S-Video Tape

Recorder

DIGTAL

Display

Monitor

RGB IN

S-VIDEO

COMPO

NENT

VIDEO

RGB OUT

CONTROL

VIDEO

(MONO)/L

AUDIO

AUDIO IN

AUDIO

OUT

C^B/PB

CR/PR

RGB

USB

DIGITAL

Speaker

with

amplifier

DVD Player

Computer (desktop type)

NOTE • When connecting with a notebook computer, set the proper RGB external image output

(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of

the notebook for more information.

Plug & Play

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer

that is VESA DDC (Display Data Channel) compatible.

Please use this function by connecting the RGB cable with RGB IN 1 terminal (DDC 1/2B

compatible), or by connecting a DVI cable with DVI terminal (DDC 2B compatible). Plug & play

may not operate by other connections.

NOTE • Plug & play is a system configured with peripheral equipment including a computer,

display and an operating system.

• This projector is recognized as a plug & play monitor. Use the standard display drivers.

• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug &

play does not operate correctly.

ENGLISH-8

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS

BLANK

RGB

STANDBY/ON

VIDEO

STANDBY/

ON Button

LASER

POWER Indicator

STANDBY/ON Button

ZOOM button

FOCUS button

AUTO

KEYSTONE

MENU SELECT

RESET

POSITION

Power Switch

FREEZE

OFF

PinP

MAGNIFY

MUTE

FOCUS button

ZOOM button

FOCUS ZOOM

VOLUME

Lens cap

Power ON

1. Check that the power cord is connected correctly.

2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to

orange.

3. Press the STANDBY/ON button

on the control panel or the remote control transmitter. Warm-up

begins and the POWER indicator blinks in green.

4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens cap.

5. Adjust picture size using the ZOOM button.

6. Adjust focus using the FOCUS button .

Power OFF

1. Press the STANDBY/ON button

on the control panel or the remote control transmitter. Then, the

message "Power off?" will appear on the screen, and the message will disappear by any operation or no

operation for 5 seconds. During this message indication, press the STANDBY/ON button again.

The projector lamp is extinguished and lamp cooling begins. The POWER indicator blinks orange

during lamp cooling. Pressing the STANDBY/ON button

is blinking.

has no effect while the POWER indicator

2. The system assumes the Standby mode when cooling is complete, and the POWER indicator ceases

blinking and changes to orange. Check that the indicator is orange and set the Power switch to [

O].

3. The POWER indicator is extinguished when power is off. Attach the lens cap.

WARNING • Please read this manual, and the separate "Safety Instruction"

Ithoroughly before using the equipment. Always ensure that the equipment

is used safely.

NOTE

• Except in emergencies, follow the above-mentioned procedure for turning power off. If the

projector is used improperly, it may be very difficult to turn off the projector caused by heating inside the

unit. And the reduction of life time of lamp and LCD panels will be caused by incorrect procedure.

• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF.

Providing a RS-232C cable is connected, turn on the computer before the projector.

• When a projector continues projecting the same image, the image may remain as an afterimage. Please

do not project the image same for a long time.

_{Download from Www.Somanuals.com. All Manuals Search And Download.}ENGLISH-9

OPERATIONS (continued)

Basic Operation

The basic operations shown in Table 3 is performed from the supplied remote control transmitter or

the projector control panel. Items indicated by (*) may be used from the control panel.

Table 3 . Basic Operation

Item

Description

Select Input Signal (*) : Press the INPUT button.

RGB IN 1 → RGB IN 2 → DVI

→ VIDEO → S-VIDEO → COMPONENT VIDEO (→ RGB IN 1)

Select RGB Input : Press the RGB button.

VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DVI

RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)

INPUT

SELECT

Select Video Input : Press the VIDEO button.

RGB IN 1/RGB IN 2/DVI → VIDEO/S-VIDEO/COMPONENT VIDEO

VIDEO → S-VIDEO → COMPONENT VIDEO (→ VIDEO)

• The selected signal name is displayed for approximately 3 seconds when the input

signal is changed.

Set/Clear Position Adjustment Mode : Press the POSITION button.

The [ ] icon is displayed in the POSITION mode.

Image Position Adjustment: Press the

and

buttons in the

POSITION mode.

• Valid only in the MAGNIFY mode with a video signal is input.

POSITION

• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the

POSITION mode is cleared automatically.

•

and

buttons may operate as the mouse control button. Refer to page 4.

Initialize Each Item : Select an item and press the RESET button.

Initialize Position Adjustment : Press the RESET button and the

POSITION mode. This function is valid only when RGB signal is input.

• Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.

• The RESET button may operate as the mouse control button. Refer to page 4.

RESET (*)

Set MAGNIFY Mode : Press the MAGNIFY

button.

Move Magnified Area : Run the POSITION in the MAGNIFY mode.

Adjust Magnification : Press the MAGNIFY

mode.

Clear MAGNIFY Mode : Press the MAGNIFY

• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT

button in MAGNIFY

MAGNIFY

OFF

button.

SELECT or VIDEO, or by changing the input signal.

Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is

displayed, and the image is frozen, in the FREEZE mode.

• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,

Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the input

signal.

FREEZE

• Do not forget to clear frozen static images.

NOTE • Use the remote control transmitter at a distance of approximately 5m from the sensor on

the front of the projector, and within a range of 30° left-right. Strong light and obstacles will

interfere with operation of the remote control transmitter.

ENGLISH-10_{Download from Www.Somanuals.com. All Manuals Search And Download.}

OPERATIONS (continued)

Items indicated by (*) may be used from the control panel.

Table 3. Basic Operation (continued)

Item

Description

VOLUME

Volume Adjustment : Press the VOLUME

button.

Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the

MUTE mode.

MUTE

AUTO

Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal

position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and

horizontal size(H.SIZE) are automatically adjusted. Use with the window at

maximum size in the application display.

Automatic Adjustment at Video Input : Press the AUTO button. A signal

type appropriate for the input signal is selected automatically. Valid only

when AUTO is set for VIDEO on the menu.

• This operation requires approximately 10 seconds. It may not function correctly with

some input signals.

BLANK

Set/Clear Blank Mode: Press the BLANK button. No image is displayed in

ON/OFF

the Blank mode. The screen color is as set in BLANK on the Image menu.

Menu Display Start/Stop: Press the MENU button.

• The menu display is terminated automatically after approximately 10 seconds of

inactivity.

ON/OFF (*)

Select Menu Type: Press the MENU SELECT button. Allows the user to

select the normal menu or the single menu. Only the selected item is

displayed on the single menu, and other items are displayed with the

and

buttons as with the normal menu.

• Valid only when the Setup menu is used. Push the MENU SELECT button after

selecting items such as "BRIGHTNESS".

• The MENU SELECT button may operate as the mouse control button. Refer to

page 4.

SELECT

Normal menu

Single menu

(MENU SELECT)

SETUP

INPUT

IMAGE

OPT.

BRIGHT

CONTRAST

-2

POSIT

PHASE

100

SIZE

800

COLOR BAL

ASPECT

CONTRAST

-2

Select Mode of P.IN P. Display : Press the PinP button.

Small → Large → P.IN P. off ( → Small)

• P.IN P. function superimposes a video image over RGB or DVI signals.

P.IN P.

MODE

ZOOM (*)

Adjust Screen Size : Press the ZOOM

Adjust Focus : Press the FOCUS

Set / Clear KEYSTONE Mode : Press the KEYSTONE

button.

FOCUS (*)

button.

Select KEYSTONE Mode : Press the button in the KEYSTONE mode.

Vertical Horizontal

Adjust KEYSTONE : Press the

↔

KEYSTONE

button.

(*)

• The image may not be appeared properly when this function is activated on some

input signals.

• The adjustable range of distortion correction will be different among input signals.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-11

OPERATIONS (continued)

SETUP

INPUT

IMAGE

OPT.

SETUP

BRIGHT

CONTRAST

SHARPNESS

COLOR

TINT

H PHASE

COLOR BAL

ASPECT

INPUT

IMAGE

OPT.

Setup Menu

-2

BRIGHT

CONTRAST

V POSIT

H POSIT

H PHASE

The following adjustments and settings are possible

when SETUP is selected at the top of the menu. Part

of the Setup menu differs between RGB input and

100

H SIZE

800

COLOR BAL R

COLOR BAL B

ASPECT

video input. Select an item with the

and

buttons, and start operation. Use the Single menu to

reduce menu size (see Table 3, MENU SELECT).

RGB IN 1

RGB IN 2

DVI

VIDEO

S-VIDEO

COMPONENT VIDEO

Table 4. Setup Menu

VIDEO

S-VIDEO

COMPONENT

RGB IN 1

RGB IN 2

DVI

Item

Description

✔

BRIGHT

Adjustment: Dark

Adjustment: Weak

Adjustment: Down

Adjustment: Left

↔ Light

↔ Strong

↔ Up

CONTRAST

V POSIT

H POSIT

↔ Right

✔

H PHASE

H SIZE

• Adjust to eliminate flicker.

Adjustment: Small ↔ Large

• The image may not be displayed correctly if the horizontal

size is excessive. In such cases, press the RESET button,

and initialize the horizontal size.

✔

SHARPNESS

COLOR

Adjustment: Soft

Adjustment: Light

Adjustment: Red

↔ Clear

↔ Dark

↔ Green

✔

TINT

• Valid only when NTSC or NTSC 4.43 signal is received.

✔

COLOR BAL R

COLOR BAL B

Adjustment: Light

↔ Dark

Adjustment: Light

↔ Dark

Select Image Aspect Ratio :

4:3[ 16:9[

Select Position of Image:

]

↔

]

✔

Press the

button while 16:9[

] is selected.

Center →

Down →

Up ( → Center )

Select Image Aspect Ratio:

4:3[ 16:9[

Select Position of Image :

]

↔

]

↔

4:3 small[

]

ASPECT

Press the

is selected.

Center →

button while 16:9[

] / 4:3 small[

✔

Down →

Up ( → Center

)

• 4:3 small cannot be selected with the input of 720P or

1080i component.

• 4:3 small may not be displayed correctly with some input

signals.

ENGLISH-12_{Download from Www.Somanuals.com. All Manuals Search And Download.}

OPERATIONS (continued)

Input Menu

menu. Select an item with the

operation with the and

effective on video input mode only, not on RGB input mode, except in

the P.IN P. window on RGB input mode.

SETUP

AUTO

RGB

VIDEO

VIDEO NR

Progressive

BLACK

INPUT

IMAGE

OPT.

The following functions are available when INPUT is selected on the

EXECUTE

CANCEL

and

buttons, and start or stop

buttons. The function indicated (**) are

HDTV

Table 5. Input Menu

Item

Description

Automatic Adjustment at RGB Input: Select the EXECUTE with the

button.

Horizontal position (H.POSIT), vertical position (V.POSIT), clock phase (H.PHASE),

and horizontal size (H.SIZE) are automatically adjusted. Use with the window at

maximum size in the application display.

Automatic Adjustment at Video Input: Select the EXECUTE with the

signal type appropriate for the input signal is selected automatically when EXECUTE

is selected automatically. Valid only when AUTO is set for VIDEO on the menu.

button. A

AUTO

•

This operation requires approximately 10 seconds. It may not function correctly with

some input signals. Pressing the AUTO button in this case may correct this problem.

• This function is the same as for the AUTO function in Basic operation.

Displays RGB Input Frequency: Displays the horizontal and vertical sync signal

frequencies for RGB input.

• Valid only at RGB input.

RGB

Select Video Signal Type: Select the signal type with the

and

buttons.

Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as appropriate for the

input signal. The selection of AUTO enables and executes the function AUTO

(Automatic Adjustment at Video Input), except for the N-PAL input.

• Use this function when the image becomes unstable (eg. the image becomes

irregular, or lacks color) at VIDEO/S-VIDEO input.

• Automatic Adjustment requires approximately 10 seconds. It may not function

correctly with some input signals. Pressing the AUTO button in this case may correct

this problem except for the N-PAL input.

VIDEO (**)

• For the COMPONENT VIDEO input, this function is not effective and the signal type

is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the

signal of HDTV.

Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with the

VIDEO NR

button. When the TURN ON is selected, the NR mode is active and the noise on

screen of the video input will be reduced.

• Valid except for the HDTV.

(**)

Select Progressive Mode: Select the mode suitable for the input signal with the

and

buttons. The TV mode and the FILM mode convert the interlaced video signal

Progressive

into the progressive signal. The FILM mode is adptable 2-3 Pull-Down system to the

conversion.

(**)

• Use this function to raise resolution, at the interlaced video input except HDTV

signal.

Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with the

button. When the TURN ON is selected, the black enhancement mode is

BLACK(**)

active and the contrast ratio of the screen for the video input will be raised by making

black level darker.

Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input

HDTV (**)

signal with the

button.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-13

OPERATIONS (continued)

Image Menu

SETUP

BLANK

START UP

MyScreen

MIRROR

P.IN P. POSIT

P.IN P. INPUT

GAMMA

INPUT

IMAGE

OPT.

MyScreen

ORIGINAL

The following adjustments and settings are available when IMAGE is

selected on the menu. Select an item with the

start or stop operation with the

and

buttons, and

and

buttons.

Table 6. Image Menu

Item

Description

Select Blank Screen: Select the screen in case of the BLANK mode with the

button.The selected one (MyScreen, ORIGIAL or one colors) is displayed when the

BLANK mode is ON.

MyScreen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

• When MyScreen or ORIGIAL is selected, the screen is going to the black after

several minutes.

BLANK

Select Start Up Screen:Select the screen in case of no signal input with the

button. The selected one (MyScreen, ORIGIAL or TURN OFF) is displayed when no

signal is input

MyScreen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

TURN OFF displays the blue screen.

START UP

• When MyScreen or ORIGIAL is selected, the screen is going to the black after

several minutes.

Set MyScreen Mode: Select the EXECUTE with the

button to display the

MyScreen menu and set the MyScreen mode for BLANK and START UP functions.

ESC clears and closes the menu box.

NORM. is default of the MyScreen menu.

FREEZE freezes the image and displays the frame to capture.

Press the

button after freeze to go to the MyScreen Capture Position mode.

In the MyScreen Capture Position mode, the buttons

move the frame to capture.

and

allow to

After adjusting the position, press the KEYSTONE button to go to the MyScreen

Display Size mode.

MyScreen

To cancel freezing and return to the NORM. of the MyScreen menu, press the

RESET button.

In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with the

button

After selecting the magnification, press the KEYSTONE button to go to the CAPT.

mode and start capturing.

To return to the MyScreen Capture Position mode, press the RESET button.

CAPT. executes a capturing the image. It requires about 20 seconds. After capturing,

the captured image will be displayed for about 10 seconds.

MIRROR

Select Mirror Status: Select mirror status with

button.

Select Position of P. in P. Display : Press the

P. IN P.

POSIT

↔

• P.IN P. function superimposes a video image over RGB or DVI signals.

Select signal of P. in P. Display : Press the button.

VIDEO S-VIDEO COMPONENT

Select Gamma Mode: Select the gamma mode with the

NORMAL CINEMA DYNAMIC

P. IN P.

INPUT

↔

button.

GAMMA

↔

ENGLISH-14_{Download from Www.Somanuals.com. All Manuals Search And Download.}

OPERATIONS (continued)

Options Menu

selected on the menu. Select an item with the

start operation.

SETUP

VOLUME

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

INPUT

IMAGE

OPT.

The following adjustments and settings are available when OPT. is

and

buttons, and

Table 7. Options Menu

Item

Description

VOLUME

Volume Adjustment: Reduce VOLUME

↔ Increase VOLUME

MENU COLOR Select Menu Background Color: Select with the

and

buttons.

Operation Start/Stop: Press the

Select Menu Display Language: Select with the

button.

LANGUAGE

AUTO OFF

and

buttons.

Operation Start/Stop: Press the

Set AUTO OFF: Set 1~99 minutes with the

system automatically enters the standby mode when a signal is not

received for the set time.

button.

and

buttons. The

Clear AUTO OFF: Select STOP (0 min.) with the

button. When

STOP is selected the system does not enter the standby mode even if

no signal is received.

Operation Start/Stop: Press the

button.

SYNC ON G Valid: Select TURN ON with the

SYNC ON G Invalid: Select TURN OFF with the

button.

SYNC ON G

WHISPER

• May not be displayed correctly with some input signals when SYNC ON G is

valid. In such cases, remove the signal connector so that no signal is received,

set SYNC ON G to invalid, and reconnect the signal.

Set / Crear WHISPER Mode: Press the

button. When the

WHISPER is selected, the WHISPER mode is active. In the WHISPER

mode, acoustic noise level from the unit is reduced, and brightness level

on screen is a little lower.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-15

OPERATIONS (continued)

No Signal Menu

VOLUME

BLANK

START UP

MIRROR

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

The same adjustments and settings are available with the Image and

Options menus when the MENU button is pressed during display of the

“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE

ON ***” message while no signal is received.

Table 8. No Signal Menu

Item

Description

Volume Adjustment: Reduce VOLUME

↔ Increase VOLUME

• When this function is used, audio input is automatically switched to video. The

audio input can be switched by moving the DISK PAD left and right during the

display of the volume adjustment bar. The volume adjustment bar is displayed by

VOLUME

pressing VOLUME

or VOLUME

button.

Select Blank Screen: Select the screen in case of the BLANK mode with the

button.The selected one (MyScreen, ORIGIAL or one colors) is displayed

when the BLANK mode is ON.

MyScreen is a mode that the customer-customized screen is displayed. This is

the blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

• When MyScreen or ORIGIAL is selected, the screen is going to the black after

several minutes.

BLANK

Select Start Up Screen:Select the screen in case of no signal input with the

button. The selected one (MyScreen, ORIGIAL or TURN OFF) is displayed

when no signal is input

MyScreen is a mode that the customer-customized screen is displayed. This is

the blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

TURN OFF displays the blue screen.

• When MyScreen or ORIGIAL is selected, the screen is going to the black after

several minutes.

START UP

MIRROR

Operation Start/Stop: Press the

button.

Select Mirror Status: Select the mirror status with the

and

buttons.

MENU COLOR Select Menu Background Color: Select the color with the

and

buttons.

Operation Start/Stop: Press the

button.

LANGUAGE

AUTO OFF

Select Menu Display Language: Select the language with the

and

buttons.

Operation start/stop: Press the

Set AUTO OFF: Set 1~99 minutes with the and

automatically enters the standby mode when a signal is not received for the set

time.

Clear AUTO OFF: Select the STOP (0 min.) with the

button.

buttons. The system

button. When the STOP

is selected the system does not enter the standby mode even if no signal is

received.

Operation Start/Stop: Press the

button.

SYNC ON G Valid: Select the TURN ON with the

button.

SYNC ON G Invalid: Select the TURN OFF with the

SYNC ON G

WHISPER

• May not be displayed correctly with some input signals when the SYNC ON G is

valid. In such cases, remove the signal connector so that no signal is received,

set the SYNC ON G to invalid, and reconnect the signal.

Set / Crear WHISPER Mode: Press the

button. When the WHISPER is

selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise

level from the unit is reduced, and brightness level on screen is a little lower.

ENGLISH-16_{Download from Www.Somanuals.com. All Manuals Search And Download.}

MAINTENANCE

Lamp

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Contact your dealer before replacing the lamp.

For the optional lamp, see the item “Option Parts” of the Table 12.

Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and

wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high

temperatures.

WARNING A mercury lamp used in this LCD projector is made of glass and has high

internal pressure. The mercury lamp can burst with a big noise due to deterioration

resulting from a shock, crack and passage of time, and can end its service life in unlit

condition. Lamps also have a considerably different service life and can sometimes end up

in burst or turn to unlit condition soon after use. Furthermore, when the lamp is blown up,

glass fragments can get scattered around the lamp house and some gas containing mercury

inside the lamp can leak out of the projector’s air vent.

• Handle the lamp with utmost care as it can burst during use if subjected to a shock or

impact or if scratched or cracked.

• Probability for the burst will increase if the lamp is used for extended period of time or

used exceeding the period of replacement. You are advised to follow instructions for lamp

replacement as soon as they are given (Refer to Table 9 of Page 20, Table 10 of Page 21).

Avoid any reuse of an old lamp (used lamp) since such reuse can result in burst.

• In case the lamp gets blown up in a short period of time after use, some electrical failures

or troubles other than the lamp itself may be suspected as causes. Under such

circumstances, consult the store where you purchased it or a service company.

• Should the lamp burst (accompanied by a big bursting noise), perform ventilation

sufficiently, and exercise maximum caution not to inhale any gas out of the projector’s air

vent or not to let it enter your eyes or mouth.

• Should the lamp burst (accompanied by a big bursting noise), make absolutely sure to

unplug the power cord from the outlet and ask the store where you bought the lamp for

immediate replacement. You should not engage in cleanup or replacement of the lamp by

yourself since scattered glass fragments can damage the inside of projector or can result in

personal injury when you handle it.

• When you dispose of any used lamps, be sure to observe and follow local ordinances and

regulations of the area or district where they are subjected to disposal. Generally speaking,

the lamps are treated similarly as glasses and bottles in most cases, but there are areas or

districts where lamps are classified as a separate collection, and so be sure to use caution.

• Never use the lamp in a state where the lamp cover is removed.

Lamp Life

Projector lamps have a finite life. The image will become darker, and hues will become weaker,

after a lamp has been used for a long period of time.

Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears

when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before

replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.

If the LAMP indicator is still red, replace the lamp.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-17

MAINTENANCE (continued)

Replacing the Lamp

1. Switch the projector OFF, remove the power cord from the

power outlet, and wait at least 45 minutes for the unit to cool.

2. Prepare a new lamp.

3. Check that the projector has cooled sufficiently, and gently

turn it upside down.

4. Loosen the screw as shown in the diagram, and remove the

lamp cover.

5. Loosen the two screws, and gently remove the lamp while

holding the grips. Touching the inside of the lamp case may

result in uneven coloring.

6. Install the new lamp and tighten the two screws firmly. Also

steadily push the opposite side of the screwed lamp into the

unit.

7. Replace the lamp cover in position and tighten the screw

firmly.

8. Gently turn the projector right-side up.

CAUTION • Ensure that screws are tightened

properly. Screws not tightened fully may result

in injury or accidents.

• Do not use the projector with the lamp cover

removed.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP

indicator is red, or the CHANGE THE LAMP message is displayed, complete the following

operation within ten minutes of switching power ON. The power will be turned off automatically in

over 10 minutes.

1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP

xxxx hr’ message will appear on the lamp timer on the bottom of the screen.

2. Press the MENU button on the remote control transmitter, or the RESET button on the control

panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 I CANCEL’ message will

then appear.

3. Press the

and select 0, and wait until the timer display is cleared.

NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always

when replacing the lamp. The message functions will not operate properly if the lamp timer is not

reset correctly.

ENGLISH-18_{Download from Www.Somanuals.com. All Manuals Search And Download.}

MAINTENANCE (continued)

Air Filters

filter cover

Cleaning Air Filters

This projector uses 2 air filters. These air filters should be

cleaned as described below at intervals of approximately

100 hours.

1. Switch the projector power supply OFF, and remove the

power cord from the power outlet.

2. Remove the filter cover and the air filter.

3. Clean the air filter with a vacuum cleaner.

4. Set the air filter and the filter cover.

filters

Replacing the Air Filter

Replace the air filter if contamination cannot be removed, or if it is damaged.

1. Switch the projector power supply OFF, and remove the power cord from the power outlet.

2. Remove the filter cover and the old filter.

3. Set the new filter and the filter cover.

CAUTION • Switch power OFF and remove the power cord from the power

outlet before beginning maintenance work. Please read the separate “Safety

Instruction” thoroughly to ensure that maintenance is performed correctly.

• Replace the air filter if contamination cannot be removed, or if it is damaged.

Contact your dealer in such case. For the optional air filter, see the item “Optional

Parts” of the Table 12.

• Do not use the equipment with the air filter removed.

• When the air filter is clogged with dust etc. the power supply is switched OFF

automatically to prevent the temperature rising inside the projector.

Other Maintenance

Maintenance Inside the Equipment

For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two

years. Maintaining the equipment by yourself is dangerous.

Cleaning the Lens

Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.

Cleaning the Cabinet and Remote control transmitter

Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth

dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.

CAUTION • Switch power OFF and remove the power cord from the power

outlet before beginning maintenance work. Please read the separate “Safety

Instruction” thoroughly to ensure that maintenance is performed correctly.

• Do not use detergents or chemicals other than those noted above (e.g. benzene

or thinners).

• Do not use cleaning sprays.

• Do not rub with hard materials, or tap the equipment.

NOTE • When this projector is brought into a warm room from a cold outdoor, condensation can

take place on the projection lens and mirror inside, blurring the screen and reducing your eyesight,

but do not worry. The condensation will disappear and the screen will return to a normal condition

no sooner than the projector acclimates to the surrounding temperature.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-19

TROUBLESHOOTING

OSD Message

The messages as described below may appear on the screen at power ON. Take the appropriate

measures when such messages appears.

Table 9. OSD Message

Message

Contents

The usage time of lamp will be reaching 2000 hr

shortly.(*2)

It is recommended to replace the lamp soon. Prepare a

new lamp as a replacement.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

(*1)

The usage time of lamp will be reaching 2000 hr shortly.

It is recommended to replace the lamp within * *

hours.(*2)

It might be happened that the lamp is cut off before * * hr

by any chance. Power will be switched OFF

automatically in * * hours. Replace the lamp as shown in

P.17~18 “Lamp”. Always reset the lamp timer after

replacing the lamp.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL TURN OFF

AFTER ** hr.

(*1)

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL

TURN OFF

The usage time of lamp is about to reach. Power will be

switched OFF in a few minutes.(*2)

Switch power OFF immediately and replace the lamp as

shown in P.17 ~18 “Lamp”. Always reset the lamp timer

after replacing the lamp.

AFTER 0 hr.

NO INPUT IS DETECTED

No input signal found.

Check signal input connections and signal sources.

ON ***

The horizontal or vertical frequency of the input signal is

not within the specified range.

Check the specifications of the equipment and the signal

source.

SYNC IS OUT OF RANGE

ON ***

The internal temperature has risen.

Switch power OFF, and wait 20 minutes until the

equipment cools.

Check the following and Switch power ON again.

* Are the ventilation openings blocked.

* Is the air filter dirty.

CHECK THE AIR FLOW

* Is the ambient temperature in excess of 35°C.

NOTE (*1) This message is cleared automatically after approximately three minutes, and

appears every time power is switched ON.

(*2) The unit has a function to turn the power off which will be active when the usage time reaches

2000 hr. However the life of lamp might be much different among lamps, so that it might be

happened that a lamp is cut off before the function is active.

ENGLISH-20_{Download from Www.Somanuals.com. All Manuals Search And Download.}

TROUBLESHOOTING (continued)

Indicators Message

The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the

appropriate measures.

Table 10. Indicators Message

POWER

indicator indicator indicator

LAMP

TEMP

Contents

Lights

orange

Turns off Turns off The Standby mode has been set.

Turns off Turns off Warming up. Please wait.

Turns off Turns off ON. Normal operation possible.

Blinks

green

Lights

green

Blinks

orange

Turns off Turns off Cooling. Please wait.

Lamp is not lit.

The interior of the equipment may be too hot. Switch

power OFF, wait 20 minutes until the equipment cools,

Turns off and check whether the ventilation openings are blocked,

whether the air filter is dirty, or whether the ambient

Lights

red

Lights red

temperature exceeds 35 °C. And switch power ON

again. Replace the lamp if the same problem occurs.

Lamp or lamp cover is not found, or hasn’t been fitted in

correctly.

Blinks

red

Switch power OFF, and wait for 45 minutes until the

equipment cools. Check fitting of the lamp and lamp

Turns off

cover, and switch power ON again. Contact your dealer if

the same problem occurs again.

The cooling fan is not operating.

Switch power OFF, and wait for 20 minutes until the

equipment cools. Check for foreign matters in the fan,

and switch power ON again. Contact your dealer if the

Blinks

red

Lights red Turns off

same problem occurs again.

The interior of the equipment is too hot.

Switch power OFF, and wait for 20 minutes until the

equipment cools. Check whether the ventilation openings

are blocked, whether the air filter is dirty, or whether the

Lights

red

ambient temperature exceeds 35 °C. Then switch power

ON again. Contact your dealer if the same problem

occurs again.

NOTE When the internal temperature becomes excessive power is switched OFF automatically

for safety reasons, and the indicator is extinguished. Set the power switch to [

O] and wait for 20

minutes until the equipment has cooled sufficiently.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-21

TROUBLESHOOTING (continued)

Symptom

Before requesting repair, check in accordance with the following chart. If the situation cannot be

corrected, then contact your dealer.

Table 11. Symptom

Symptom

Possible cause

Remedy

Page

The main power switch is not

turned on.

Turn on the main power switch.

8,9

The power cord is

disconnected.

Plug the power cord into an AC

power outlet.

The power is not

turned on.

Turn off the projector with the main

power switch (set the power switch

to [O]), and wait for about 20

The main power was

disconnected during operation

by the power failure and so on. minutes. When the equipment has

cooled enough, turn power on.

Use the projector or remote control

The input is not correctly set.

7,8

transmitter to set.

No video or audio.

No signal input.

Connect correctly.

The projector is not correctly

connected.

Connect correctly.

Press VOLUME

control or display the menu screen

and adjust the volume.

on the remote

Video is present but

no audio.

The volume is set to minimum.

11,15

Mute is turned on.

Press the MUTE

Connect correctly.

button.

The projector is not correctly

connected.

7,8

Audio is present but

no video.

Select BRIGHT with the MENU

The brightness adjustment knob

is rotated fully clockwise.

button and the press the

button.

The lens cap is still attached.

Remove the lens cap.

Colors are pale and Color density and color

color matching is

poor.

matching are not correctly

adjusted.

Adjust the video.

Brightness and contrast are not

correctly adjusted.

Adjust the video.

Images are dark.

Video is blurred.

The lamp is nearing the end of

its service life.

Replace with a new lamp.

Adjust the focus or H PHASE.

Focus or H PHASE is out of

adjustment.

9,12

ENGLISH-22_{Download from Www.Somanuals.com. All Manuals Search And Download.}

SPECIFICATIONS

Table 12. Specifications

Item

Specification

Product name

Liquid crystal projector

Panel size

3.3 cm (1.3 type)

TFT active matrix

Liquid

crystal

panel

Drive system

Pixels

786,432 pixels (1024 horizontal x 768 vertical)

Zoom lens F=1.7 ~ 2.3 f=49.0 ~ 64.0 mm

275 W UHB

Lens

Lamp

Speaker

1.2 W + 1.2W (Stereo)

Power supply

Power consumption

Temperature range

Size

AC100 ~ 120V, 4.7A / AC220 ~ 240V, 2.0A

440W

0 ~ 35°C (Operating)

289 (W) x 144 (H) x 350 (D) mm

6.5 kg

Weight (mass)

Video: Analog 0.7Vp-p, 75Ω terminator (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB IN

RGB

D-sub 15-pin shrink jack

signal

input

TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p

TTL Level (Positive/Negative)

DVI

RGB1

DVI

RGB2

200mVrms, 50 kΩ (max. 3.0Vp-p)

Stereo mini jack

AUDIO IN

VIDEO

1.0Vp-p, 75Ω terminator

RCA jack

Brightness signal: 1.0Vp-p, 75Ω terminator

Color signal: 0.286Vp-p (burst signal), 75Ω terminator

Mini DIN 4-pin jack

S-VIDEO

Video

signal

1.0 Vp-p, 75 Ω Terminator (Positive)

COMPONENT

input

CB/PB 0.7 Vp-p, 75 Ω Terminator (Positive)

VIDEO

CR/PR 0.7 Vp-p, 75 Ω Terminator (Positive)

L/MONO

200mVrms, 50 kΩ (max. 3.0Vp-p)

RCA jack

AUDIO

Video: Analog 0.7Vp-p, 75Ω output impedance (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB OUT

Signal

output

D-sub 15-pin shrink jack

200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)

Stereo mini jack

AUDIO OUT

CONTROL

USB

D-sub 15-pin shrink plug

USB jack (B type)

Control

functions

Lamp: DT00491

Air Filter: MN04531

Optional Parts

* For others, consult your dealer.

NOTE • This specifications are subject to change without notice.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-23

ENGLISH-24_{Download from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL

Dimension Diagram

289

308.5

Unit : mm

30.5

Signal Connector Pin Assignment

1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)

Pin No

Signal

Video input Red

Video input Green

Video input Blue

Pin No

Signal

Pin No

Signal

RGB IN 1: SCL(DDC)

Ground

RGB IN 2:

RGB OUT:

RGB IN 1: SDA(DDC)

Ground

RGB IN 2:

RGB OUT:

Ground Red

Ground Green

Ground Blue

H. sync./ Composite sync.

Vertical sync

2. Digital Receptacle Connector (DVI)

Pin No

Signal

T.M.D.S. Data 2 -

T.M.D.S. Data 2 +

T.M.D.S. Data 2 / 4 Shield

Pin No

Signal

Pin No

Signal

T.M.D.S. Data 1 / 3 Shield

T.M.D.S. Clock Shield

T.M.D.S. Clock +

T.M.D.S. Clock -

+5V Power

Ground (+5V, Analog H/V Sync.)

Hot-Plug Sense

T.M.D.S. Data 0 -

T.M.D.S. Data 0 +

T.M.D.S. Data 0 / 5 Shield

DDC Clock

DDC Data

10 11 12 13 14 15 16

Analog V. Sync.

T.M.D.S. Data 1 -

T.M.D.S. Data 1 +

17 18 19 20 21 22 23 24

3. Mini Din 4-pin Connector (S-VIDEO)

Pin No

Signal

Color:0.286Vp-p (NTSC, burst signal),75Ω terminator

0.3Vp-p (PAL/SECAM, burst signal),75Ω terminator

Brightness:1.0Vp-p, 75Ω terminator

Ground

TECHNICAL - 1

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Example of computer signal

Resolution

Display

mode

fH (kHz)

fV (Hz)

Rating

Signal mode

H × V

720 × 400

640 × 480

800 × 600

832 × 624

1024 × 768

1152 × 864

1280 × 960

1280 × 1024

37.9

31.5

35.0

37.9

37.5

43.3

35.2

37.9

48.1

46.9

53.7

49.7

48.4

56.5

60.0

68.7

67.5

60.0

64.0

80.0

85.0

59.9

66.7

72.8

75.0

85.0

56.3

60.3

72.2

75.0

85.1

74.5

60.0

70.1

75.0

85.0

75.0

60.0

75.0

VESA

TEXT

Zoom in

VGA (60Hz)

Mac13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

SXGA (75Hz)

SXGA (60Hz)

SXGA (75Hz)

VESA

Zoom out

1600 × 1200

75.0

60.0

VESA

VXGA (60Hz)

NOTE • Some computers may have multiple display screen modes. Use of some of these modes

will not be possible with this projector.

• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a

computer.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the

number of display pixels above.

• The image may not be displayed correctly when the input sync. signal is "Composite Sync." or

"Sync. on G".

• The image might be something wrong with computer by computer on the DVI mode. In the case, it

is recommended to reduce the resolution and / or reflesh rate.

TECHNICAL_D-_o2_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Initial set signals

The following signals are used for the initial settings.

The signal timing of some computer models may be different. In such case, refer to adjust the

V.POSIT and H.POSIT of the menu.

Back porch b

Front porch d

Back porch b

Display interval c

Front porch d

Display interval c

Sync a

Computer /

Sync a

Horizontal signal timing (µs)

Computer /

Signal

Vertical signal timimg (lines)

Signal

400

TEXT

2.0

3.0

20.3

1.0

TEXT

VGA (60Hz)

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

1600×1200 (60Hz)

3.8

2.1

1.3

2.0

1.6

2.0

3.2

2.4

1.6

1.1

2.1

1.8

1.2

1.0

1.2

1.0

1.1

1.2

1.9

3.2

3.8

2.2

3.6

2.2

1.3

3.2

2.7

3.9

2.5

1.9

2.2

2.4

2.9

2.3

1.8

1.9

25.4

21.2

20.3

17.8

22.2

20.0

16.0

16.2

14.2

14.5

15.8

13.7

13.0

10.8

10.7

11.9

9.5

0.6

2.1

1.0

0.5

1.6

0.7

1.0

1.1

0.3

0.6

0.4

0.3

0.2

0.5

0.6

0.9

0.4

0.1

0.4

VGA (60Hz)

480

600

624

768

864

960

1024

1200

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

1600×1200 (60Hz)

9.9

TECHNICAL - 3

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Connection to the Mouse Control

1. PS/2, ADB or Serial Mouse

(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For

PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult

your dealer.

(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.

(3) Turn on the computer.

(4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or

reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.

2. USB Mouse

(1) Connect the projector and computer with a suitable commercially available USB cable. Consult

your dealer to get the cable, if you need.

(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT

button” of page 4.

NOTE • Before connecting, read the instruction manuals of the devices to be connected.

• In the case of notebook type computers with an internal pointing device, the mouse control

function will not work unless the internal pointing device is disabled. In such case, disable the

internal pointing device and change the BIOS setting to select an external mouse before the

operations described in (1) to (4) above.

Also, some computers may not have a utility program to operate a mouse.

Refer to the computer hardware manual for detail.

PS/2 Mouse

Projector

Computer

DATA

CLK

DATA

Mouse jack

Mini DIN 6-pin

CONTROL Terminal

GND

+5V

CLK

D-sub 15-pin shrink jack

SEL0

RTS

+5V

GND

TECHNICAL_D-_o4_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

ADB Mouse

Projector

Computer

ADB

(

)

POWER ON

CONTROL Terminal

DATA

RTS

+5V

GND

Mouse jack

Mini DIN 4-pin

D-sub 15-pin shrink jack

+5V

GND

Serial Mouse

Projector

Computer

CONTROL Terminal

DTR

GND

DSR

RTS

CTS

Mouse jack

D-sub 9-pin

D-sub 15-pin shrink jack

SEL0

RTS

GND

USB Mouse

USB jack

(B type)

Projector

Computer

1 +_5V

USB jack

(A type)

—

DATA

DATA 3

GND

DATA

GND

USB cable

TECHNICAL - 5

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

RS-232C communication

(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.

(2) Turn on the computer power supply and, after the computer has started up, turn on the projector

power supply.

Projector

Computer

RS-232C jack

D-sub 9-pin

Control jack

D-sub 15-pin shrink jack

DTR

GND

DSR

RTS

CTS

SELO

RTS

GND

Communications setting

19200bps, 8N1

1 Protocol

Consist of header (7 bytes) + command data (6 bytes).

2 Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low : Lower byte of CRC flag for command data.

CRC_high : Upper byte of CRC flag for command data.

3 Command data

Command data chart

byte_0

byte_1

high

byte_2

byte_3

byte_4

Setting code

low high

byte_5

Action

Type

low

high

Action (byte_0 - 1)

Action

Classification

Content

SET

GET

Change setting to desired value.

Read projector internal setup value.

Increment setup value by 1.

Decrement setup value by 1.

Run a command.

INCREMENT

DECREMENT

EXECUTE

TECHNICAL_D-_o6_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)

from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2

bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2

bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the specified setting to the default value.

(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)

+‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)

+‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

When a command sent by the projector cannot be understood by the computer

When the command sent by the projector cannot be understood, the error command ‘15H’ is

returned by the computer. Some times, the projector ignores RS-232C commands during other

works. If the error command ‘15H’ is returned, please send the same command again.

When data sent by the projector cannot be practice

When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is

returned.

When the data length is greater than indicated by the data length code, the projector will ignore the

excess data code.

Conversely, when the data length is shorter than indicated by the data length code, an error code

will be returned to the projector.

NOTE • Operation cannot be guaranteed when the projector receives an undefined command or

data.

•

Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.

Ignore this data.

• Commands are not accepted during warm-up.

TECHNICAL - 7

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Red

Orange

Green

Blue

BE EF

06 00 3B D3 01 00 00 30

06 00 AB D2 01 00 00 30

06 00 5B D2 01 00 00 30

06 00 CB D3 01 00 00 30

06 00 FB D1 01 00 00 30

06 00 6B D0 01 00 00 30

06 00 9B D0 01 00 00 30

06 00 FB CA 01 00 00 30

06 00 FB E2 01 00 00 30

06 00 08 D3 02 00 00 30

06 00 C7 D2 01 00 01 30

06 00 57 D3 01 00 01 30

06 00 A7 D3 01 00 01 30

06 00 37 D2 01 00 01 30

06 00 F4 D2 02 00 01 30

06 00 83 D2 01 00 02 30

06 00 13 D3 01 00 02 30

06 00 B0 D2 02 00 02 30

06 00 7F D3 01 00 03 30

06 00 EF D2 01 00 03 30

06 00 1F D2 01 00 03 30

06 00 8F D3 01 00 03 30

06 00 BF D1 01 00 03 30

06 00 2F D0 01 00 03 30

06 00 DF D0 01 00 03 30

06 00 4C D3 02 00 03 30

06 00 0B D2 01 00 04 30

06 00 9B D3 01 00 04 30

06 00 CB CB 01 00 04 30

06 00 38 D2 02 00 04 30

06 00 F7 D3 01 00 05 30

06 00 67 D2 01 00 05 30

06 00 97 D2 01 00 05 30

06 00 07 D3 01 00 05 30

06 00 37 D1 01 00 05 30

06 00 A7 D0 01 00 05 30

06 00 57 D0 01 00 05 30

06 00 C7 D1 01 00 05 30

06 00 37 D4 01 00 05 30

06 00 C4 D3 02 00 05 30

00 00

01 00

02 00

03 00

04 00

05 00

06 00

20 00

40 00

00 00

01 00

02 00

03 00

00 00

01 00

00 00

01 00

02 00

03 00

04 00

05 00

06 00

00 00

01 00

20 00

00 00

01 00

02 00

03 00

04 00

05 00

06 00

07 00

08 00

00 00

Purple

White

Set

Blank Color

Black

MyScreen

ORIGINAL

Get

Normal

H Inverse

V lnverse

H&V Inverse

Get

Set

Mirror

Normal

Freeze

Get

Freeze

Red

Orange

Green

Set

Blub

Menu Color

Purple

Transparent

Gray

Get

ORIGINAL

OFF

Startup

MyScreen

Get

English

Français

Deutsch

Español

Italiano

Norsk

Set

Language

Nederlands

Português

Japanese

Get

TECHNICAL_D-_o8_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Command data chart

Command data

Action Type Setting code

Names

Operation type

Header

CRC

Get

BE EF

06 00 7C D2 02 00 07 30

06 00 1A D2 04 00 07 30

06 00 CB D3 05 00 07 30

06 00 08 86 02 00 10 31

06 00 6E 86 04 00 10 31

06 00 BF 87 05 00 10 31

06 00 58 D3 06 00 00 70

06 00 A4 D2 06 00 01 70

06 00 E0 D2 06 00 02 70

06 00 IC D3 06 00 03 70

06 00 68 D2 06 00 04 70

06 00 94 D3 06 00 05 70

06 00 D0 D3 06 00 06 70

06 00 C4 D0 06 00 09 70

06 00 80 D0 06 00 0A 70

06 00 7C D1 06 00 0B 70

06 00 08 D0 06 00 0C 70

06 00 98 D8 06 00 20 70

06 00 91 D0 06 00 0A 20

06 00 FB D8 01 00 20 30

06 00 6B D9 01 00 20 30

06 00 C8 D8 02 00 20 30

06 00 D9 D8 02 00 20 60

00 00

01 00

00 00

Magnify

Increment

Decrement

Get

Auto off

Increment

Decrement

Execute

Brightness Reset

Contrast Reset

V.Position Reset

H.Position Reset

H.Size Reset

Color Balance R Reset

Color Balance B Reset

Sharpness Reset

Color Reset

Tint Reset

Keystone_V Reset

Keystone_H Reset

Auto

off

Set

Blank on/off

Get

(Example of Return)

00 00 01 00

(Normal) (Cover-error)

02 00

03 00

(Lamp-error)

Error Status

Power

(Fan-error)

04 00

(Temp-error)

05 00

(Air flow-error)

06 00

(Lamp-Time-over)

OFF

BE EF

06 00 2A D3 01 00 00 60

06 00 BA D2 01 00 00 60

06 00 19 D3 02 00 00 60

00 00

01 00

00 00

Set

Get

RGB1

RGB2

BE EF

06 00 FE D2 01 00 00 20

06 00 3E D0 01 00 00 20

06 00 0E D2 01 00 00 20

06 00 6E D3 01 00 00 20

06 00 9E D3 01 00 00 20

06 00 AE D1 01 00 00 20

06 00 CD D2 02 00 00 20

06 00 31 D3 02 00 01 20

06 00 57 D3 04 00 01 20

00 00

04 00

03 00

01 00

02 00

05 00

02 00

00 00

Digital

Set

Input Source

Video

SVideo

Component BE EF

Get

BE EF

Increment

Volume

Decrement

BE EF

06 00 86 D2 05 00 01 20

00 00

TECHNICAL - 9

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Mute

Operation type

Normal

Header

CRC Action

BE EF

06 00 46 D3 01 00 02 20

06 00 D6 D2 01 00 02 20

06 00 75 D3 02 00 02 20

06 00 89 D2 02 00 03 20

06 00 EF D2 04 00 03 20

06 00 3E D3 05 00 03 20

06 00 FD D3 02 00 04 20

06 00 9B D3 04 00 04 20

06 00 4A D2 05 00 04 20

06 00 01 D2 02 00 05 20

06 00 67 D2 04 00 05 20

06 00 B6 D3 05 00 05 20

06 00 45 D2 02 00 06 20

06 00 23 D2 04 00 06 20

06 00 F2 D3 05 00 06 20

06 00 B9 D3 02 00 07 20

06 00 DF D3 04 00 07 20

06 00 0E D2 05 00 07 20

06 00 E9 D0 02 00 0B 20

06 00 8F D0 04 00 0B 20

06 00 5E D1 05 00 0B 20

06 00 9E D0 01 00 08 20

06 00 0E D1 01 00 08 20

06 00 FE D1 01 00 08 20

06 00 AD D0 02 00 08 20

06 00 62 D1 01 00 09 20

06 00 F2 D0 01 00 09 20

06 00 02 D0 01 00 09 20

06 00 51 D1 02 00 09 20

06 00 0D 83 02 00 00 21

06 00 6B 83 04 00 00 21

06 00 BA 82 05 00 00 21

06 00 F1 82 02 00 01 21

06 00 97 82 04 00 01 21

06 00 46 83 05 00 01 21

06 00 B5 82 02 00 02 21

06 00 D3 82 04 00 02 21

06 00 02 83 05 00 02 21

06 00 49 83 02 00 03 21

06 00 2F 83 04 00 03 21

06 00 FE 82 05 00 03 21

00 00

01 00

00 00

01 00

02 00

00 00

01 00

02 00

00 00

Set

Mute

Get

Increment

Decrement

Get

Brightness

Contrast

Increment

Decrement

Get

Color

Balance R

Increment

Decrement

Get

Color

Balance B

Increment

Decrement

Get

Keystone_V

Keystone_H

Increment

Decrement

Get

Increment

Decrement

4:3

Set

16:9

Aspect

Small

Get

Default

Bottom

Top

Display

Position at

16 : 9 or Small

Get

V.Position

H.Position

H.Size

Increment

Decrement

Get

Increment

Decrement

Get

Increment

Decrement

Get

Increment

Decrement

H.Phase

TECHNICAL_D-_o1_w0_{nload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Get

BE EF

06 00 F1 72 02 00 01 22

06 00 97 72 04 00 01 22

06 00 46 73 05 00 01 22

06 00 B5 72 02 00 02 22

06 00 D3 72 04 00 02 22

06 00 02 73 05 00 02 22

00 00

Sharpness

Increment

Decrement

Get

Increment

Decrement

Color

Tint

Get

Increment

Decrement

Auto

BE EF

06 00 49 73 02 00 03 22

06 00 2F 73 04 00 03 22

06 00 FE 72 05 00 03 22

06 00 9E 75 01 00 00 22

06 00 FE 71 01 00 00 22

06 00 6E 70 01 00 00 22

06 00 6E 75 01 00 00 22

06 00 5E 72 01 00 00 22

06 00 FE 74 01 00 00 22

06 00 0E 71 01 00 00 22

00 00

0A 00

04 00

05 00

09 00

02 00

08 00

07 00

NTSC

PAL

SECAM

NTSC 4.43

M-PAL

Set

Video Format

N-PAL

Get

off

BE EF

06 00 0D 73 02 00 00 22

06 00 B6 73 01 00 06 22

06 00 26 72 01 00 06 22

06 00 85 73 02 00 06 22

06 00 4A 72 01 00 07 22

06 00 DA 73 01 00 07 22

06 00 2A 73 01 00 07 22

06 00 79 72 02 00 07 22

06 00 5E 71 01 00 08 22

06 00 CE 70 01 00 08 22

06 00 6D 71 02 00 08 22

06 00 F2 73 01 00 05 22

06 00 62 72 01 00 05 22

06 00 C1 73 02 00 05 22

06 00 FE 22 01 00 00 23

00 00

01 00

00 00

01 00

02 00

00 00

01 00

00 00

01 00

00 00

Set

Video NR

Get

off

Progressive

FILM

Get

off

Set

Black

Get

1080i

1035i

Get

off

HDTV

Set

Large

Small

Get

BE EF

06 00 6E 23 01 00 00 23

06 00 9E 23 01 00 00 23

06 00 Cd 22 02 00 00 23

01 00

02 00

00 00

PinP Size

_{Download from Www.Somanuals.com. All Manuals Search And Dow}T_nlE_oaC_d.HNICAL - 11

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Upper left

Upper right

bottom left

bottom right

Get

BE EF

06 00 02 23 01 00 01 23

06 00 92 22 01 00 01 23

06 00 62 22 01 00 01 23

06 00 F2 23 01 00 01 23

06 00 31 23 02 00 01 23

00 00

01 00

03 00

02 00

00 00

Set

PinP Position

RGB

Video

Get

BE EF

06 00 BA 22 01 00 03 23

06 00 2A 23 01 00 03 23

06 00 89 22 02 00 03 23

00 00

01 00

00 00

Set

PinP Audio ch

PinP Input

Video

S-Video

Component

Get

BE EF

06 00 D6 22 01 00 02 23

06 00 26 22 01 00 02 23

06 00 16 20 01 00 02 23

06 00 75 23 02 00 02 23

06 00 6A 93 04 00 00 24

06 00 BB 92 05 00 00 24

06 00 96 92 04 00 01 24

06 00 47 93 05 00 01 24

06 00 CB D0 01 00 08 30

06 00 5B D1 01 00 08 30

06 00 68 D1 02 00 08 30

06 00 3B 23 01 00 00 33

06 00 AB 22 01 00 00 33

06 00 08 23 02 00 00 33

06 00 C7 F0 01 00 A1 30

06 00 57 F1 01 00 A1 30

06 00 A7 F1 01 00 A1 30

06 00 37 F0 01 00 A1 30

01 00

02 00

05 00

00 00

01 00

00 00

01 00

00 00

01 00

02 00

03 00

Increment

Decrement

Increment

Decrement

off

FOCUS

Zoom

Set

Sync on G

WHISPER

Get

NORMAL

WHISPER

Get

NORMAL

CINEMA

DYNAMIC

6500K

Set

GAMMA

Get

BE EF

06 00 F4 F0 02 00 A1 30

00 00

TECHNICAL_D-_o1_w2_{nload from Www.Somanuals.com. All Manuals Search And Download.}

REGULATORY NOTICES

EN 55022 Warning

This is a Class A product. In a domestic environment it may cause radio

interference, in which case the user may be required to take adequate measures.

The typical use is in a conference room, meeting room or auditorium.

FCC Statement Warning

WARNING:

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications, Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

INSTRUCTIONS TO USERS:

This equipment complies with the requirements of

FCC (Federal Communication Commission) Class A equipments provided that

following conditions are met.

The cables may have to be used with the core set to the projector side. Use the

cables which are included with the projector or specified.

Core

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

For the Customers in CANADA

NOTICE: This Class A digital apparatus complies with Canadian ICES-003.

Pour les utilisateurs au Canada

AVIS: Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du

Canada.

REGULATORY NOTICES - 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited

Warranty

InFocus Corporation (“InFocus”) warrants that the Projector (“Product”) purchased from InFocus, an

InFocus distributor, or an InFocus reseller will conform to the manufacturer’s specifications and be free from

defects in material or workmanship for the Warranty period provided below. InFocus does not warrant that the

Product will meet the specific requirement of the end-user customer.

If the Product, which is the subject of this Limited Warranty, is defective in material or workmanship

during the warranty period, InFocus, at its option, will REPAIR or REPLACE the Product.

All exchanged parts and products replaced under this Warranty will become property of InFocus. InFo-

cus’ sole obligation is to supply (or pay for) all labor necessary to repair the Product found to be defective within

the Warranty period and to repair or replace defective parts with new parts or, at the option of InFocus, service-

able used parts that are equivalent or superior to new parts performance.

imited

rants as follows:

arranty

Alternatives: Subject to the Limitations, Exclusions and Disclaimers, InFocus War-

・

ear arts and

abor roduct arranty - From the date of purchase, InFocus warrants that the Product

will conform to the manufacturer’s specifications and free from defects in material or workmanship for a

period of two (2) years.

・

Year

Parts

Only

Accessory

Warranty - From the date of purchase, InFocus warrants that the customer

replaceable and accessory products will conform to the manufacturers’ specifications and be free from defects in

material or workmanship for a period of one (1) year.

・

Day/500

Hour

Replacement

Lamp

Warranty - Lamp Products purchased in projectors or separately as

replacements after the original projector purchases is Ninety (90) days or 500 hours, whichever comes first. Dur-

ing the Warranty period for the Product, InFocus warrants that Replacement lamps, which are purchased at the time of pro-

jector purchase, will have a 90-day or 500 hour warranty, whichever comes first, from the date the spare lamp is put into use.

ARRANTY LIMITATION AND EXCLUSION

THIS WARRANTY SETS FORTH INFOCUS’ MAXUMUM LIABILITY FOR ITS PRODUCT. THIS WAR-

RANTY EXTENDS ONLY TO PRODUCTS PURCHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED

RESELLAER. InFocus shall have no further obligation under foregoing Limited Warranty if the Product has

been damaged due to abuse, misuse, neglect, smoke exposure (cigarette or otherwise), accident, unusual physical

or electrical stress, unauthorized modifications (including use of an unauthorized mount), tampering, alterations,

or service other than by InFocus or its authorized agents, causes other than from ordinary use or failure to prop-

erly use the Product in the application for which said Product was intended.

This Warranty excludes Product or accessory cleaning, repair, or replacement of plastics due to cosmetic

damage and damage as a result of normal wear. Product repair outside of the terms of the Limited Warranty will

be on a time and material basis. Prolonged Product “demonstration” causes manual Product wear and is not

considered normal use under the terms of this Limited Warranty.

The Accessory Warranty covers the accessory items only and excludes normal wear. The Lamp product

Warranty excludes expected lamp degradation.

Remanufactured products and Software Products are exempt from the foregoing Limited Warranty.

Please refer to the appropriate Remanufactured Product Limited Warranty or Software Product Limited War-

ranty for applicable Warranty information.

DISCLAIMER OF UNSTATED

WARRANTIES

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT.

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED.

THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND

THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN

INSTRUMENT SIGNED BY INFOCUS. SOME JURISDICTION DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.

Download from Www.Somanuals.com. All Manuals Search And Download.

imited

arranty Period

The Limited Warranty period commences on the date of purchase by the end-user customer for both

the 2 year Product Warranty and the 1 year Accessory Warranty. These Limited Warranty provisions shall

apply only to the end-user purchaser (first person or entity that purchased a new Product for personal or

business use and not for the purpose of distribution or resale).

ligible

imited

arranty

Coverage

Any person exercising a claim under Limited Warranty must establish to the satisfaction of

InFocus both the date of purchase and that the Product was purchased new. The sales receipt or invoice,

showing the date of purchase of the Product or Accessory is the proof of the date of purchase.

Obtain

arranty Service

During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first

contact 1) InFocus, 2) a service facility authorized by InFocus or 3) the place of original purchase.

InFocus Customer Service – 1-800-799-9911 or techsupport@infocus.com

For Warranty service, the purchaser will be advised to return or deliver the defective Product

freight and all fees prepaid, to an InFocus Service Center or to a service facility authorized by InFocus. When

returning Product to InFocus, a Return Material Authorization Number (RMA #) is required and must be

clearly displayed on the outside of the shipping carton or similar package affording an equal degree of pro-

tection. InFocus or the service facility authorized by InFocus will return the repaired/ replaced Product

freight prepaid to the purchaser.

Products returned for Warranty service must be accompanied by a written letter that: (i) explains

the problem; (ii) provides proof of date of purchase; (iii) provides the dealer’s name; and (iv) provides the

model and serial number of the Product. Upon request of InFocus Corporation or an authorized repair center

for InFocus, proof of legal importation must accompany the warranty repair Product, otherwise the Product

must be returned to the place of original purchase, to the manufacturer (Purchaser must bear all tax, duty and

freight), or the Purchaser must bear charges for the warranty repair.

No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to

the entire Product. Warranty on the repair part and workmanship shall only be effective for a period of

ninety (90) days following the repair or replacement of that part or the remaining period of the Product Lim-

ited Warranty whichever is greater.

LIMITATION OF LIABILITY

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY WHETHER IN CONTRACT, IN

TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE

RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIR-

CUMSTANCES SHALL INFOCUS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSE-

QUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED

FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING INFOCUS’ LIABILITY.

imitation on

the product may be brought by purchaser more than one year after the cause of action has accrued.

overning aw – Any action, regardless of form, arising out of the agreement to purchase the product is

governed by Oregon law.

andatory rbitration – Any action, regardless of form, arising out of the agreement to purchase the

ringing

Action – No action, regardless of form, arising out of the agreement to purchase

product is subject to mandatory arbitration.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE

OTHER RIGHTS, DEPENDING ON JURISDICTION.

Download from Www.Somanuals.com. All Manuals Search And Download.

Eingeschrankte Garantie

InFocus Corporation („InFocus”) garantiert, dass der von InFocus, einem InFocus-Distributor oder einem

InFocus-Wiederverkäufer erworbene Projektor („Produkt”) den technischen Angaben des Herstellers entspricht und für

die unten angegebene Garantiedauer frei von Material- und Herstellungsfehlern ist. InFocus garantiert nicht, dass das

Produkt den spezifischen Anforderungen des Endbenutzerkunden entspricht.

Falls das Produkt, das Gegenstand dieser eingeschränkten Garantie ist, während der Garantiezeit Material- oder

Herstellungsfehler aufweist, wird das Produkt nach Ermessen von InFocus REPARIERT oder ERSETZT.

Alle im Rahmen dieser Garantie ausgetauschten Teile und ersetzten Produkte gehen in das Eigentum von

InFocus über. Die ausschließliche Verpflichtung von InFocus besteht in der Bereitstellung (bzw. Bezahlung) der gesamten

Arbeitsleistung, die zum Reparieren des Produkts erforderlich ist, das während der Garantiezeit als mangelhaft festgestellt

wurde, und im Reparieren oder Ersetzen mangelhafter Teile durch neue Teile oder im Ermessen von InFocus durch

verwendbare gebrauchte Teile, die der Leistung neuer Teile gleichwertig oder besser sind.

Umfang der eingeschränkten Garantie: Vorbehaltlich der Einschränkungen und Ausschlüsse garantiert InFocus

Folgendes:

・

2-Jahre-Produktgarantie auf Teile und Arbeitsleistung - InFocus garantiert für die Dauer von zwei (2) Jahren ab

dem Kaufdatum, dass das Produkt den technischen Angaben des Herstellers entspricht und frei von Material- und

Herstellungsfehlern ist.

・

1-Jarr-Zubehörgarantie nur auf Teile - InFocus garantiert für die Dauer von einem (1) Jahr ab dem Kaufdatum, dass

kundenseitig auswechselbare Produkte und Zubehörprodukte den technischen Angaben des Herstellers entsprechen und

frei von Material- und Herstellungsfehlern sind.

・

90-Tage/500-Stunden-Ersatzlampengarantie – Auf Lampenprodukte, die in prokektoren oder gesondert als

Ersatzteile nach dem Originalkauf des projectors erworben wurden, wird eine Garantie von neunzig (90) Tagen oder 500

Stunden gewährt, je nachdem, was zuerst eintritt. Während der Garantiezeit für das Produkt gewährt InFocus auf die

Ersatzlampen, die zusammem mit dem Projektor gekauft wurden, eine Garantiedauer von 90 Tagen oder 500 Stunden, je

nachdem, was zuerst eintritt, ab dem Datum, an dem die Ersatzlampe eingesetzt wurde.

GARANTIEEINSCHRÄNKUNG UND -AUSSCHLUSS

DIESE GARANTIE LEGT DIE MAXIMALE HAFTUNG SEITENS INFOCUS FÜR INFOCUS-PRODUKTE FEST.

DIESE GARANTIE GILT NUR FÜR PRODUKTE, DIE VON INFOCUS ODER EINEM AUTORISIERTEN INFOCUS-

WIEDERVERKÄUFER ERWORBEN WURDEN. InFocus übernimmt hiermit keine Haftung, wenn das Produkt aufgrund

von Misshandlung, Missbrauch, Fahrlässigkeit, Rauch (Zigarettenrauch oder anderer Rauch), Unfall, ungewöhnlicher

physikalischer oder elektrischer Belastung, nicht genehmigten Modifikationen (einschließlich nicht genehmigter

Befestigung), unsachgemäßen Eingriffen, Änderungen, Wartung durch nicht von InFocus autorisierte Stellen, Ursachen,

die nicht auf normalen Einsatz zurückzuführen sind, oder Verwendung des Produkts in einer nicht für das Produkt

bestimmten Anwendung beschädigt wird.

Diese Garantie gilt nicht für die Produkt- bzw. Zubehörreinigung, Reparatur oder den Austausch von

Kunststoffteilen aufgrand eines kosmetischen Schadens oder Achäden infolge normaler Abnutzung. Für

Produktreparaturen, die nicht im Rahmen der eingeschränkten Garantie durchgeführt werden, werden Zeit- und

Materialkosten berechnet. Eine „Produktdemonstration” über einen längeren Zeitraum verursacht eine ungewöhnlich

hohe Produktabnutzung, die unter den Bedingungen dieser eingeschränkten Garantie nicht als normaler Gebrauch

betrachtet wird.

Die Zibehörgarantie gilt nur für das Zubehör und schließt normale Abnutzung aus. Die

Lampenproduktgarantie schließt einen erwarteten Qualitätsverlust der Lampe durch Alterung aus..

Wiederaufbereitete Produkte und Softwareprodukte sind von der vorangegangenen eingeschränkten Garantie

ausgeschlossen. Die hierfür zutreffenden Garantieinformationen sind in der eingeschränkten Garantie für das

wiederaufbereitete Produkt bzw. Das betreffende Softwareprodukt zu finden.

AUSSCHLUSS ODER STILLSCHWEIGENDE GARANTIEN

DIE OBEN AUFGEFÜHRTE GARANTIE IST DIE EINZIG GÜLTIGE GARANTIE FÜR DIESES PRODUKT.

ALLE ANDEREN, GLEICH OB AUSDRÜCKLICH ODER IMPLIZIT GEWÄHRTEN GARANTIEN, EINSCHLIESSLICH,

JEDOCH NICHT BESCHRÄNKT AUF DIE IMPLIZITEN GARANTIEN DER MARKTFÄHIGKEIT UND EIGNUNG FÜR

EINEN BESTIMMTEN ZWECK, SIND NICHT GÜLTIG. DIE OBIGE GARANTIE KANN NICHT DURCH ANDERE

GARANTIEN ERWEITERT UND NUR DURCH EINE SCHRIFTLICHE UNTERLAGE, DIE VON INFOCUS

UNTERSCHRIEBEN WURDE, ERWEITERT ODER GEÄNDERT WERDEN. EINIGE GERICHTSBARKEITEN ERLAUBEN

KEINE FRISTEN FÜR GESETZLICHE GEWÄHRLEISTUNGEN. IN DIESEM FALL TRIFFT DIE OBEN AUFGEFÜHRTE

EINSCHRÄNKUNG U.U.NICHT AUF SIE ZU.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dauer der eingeschränkten Grantie

Die Garatiezeit sowohl für die 2-Jahre-Produktgarantie als auch für die 1-Jahr-Zubehörgarantie beginnt am Tag

des Kaufs durch den Endbenutzerkunden. Die eingeschränkte Garantie gilt nur für Endbenutzerkäufer (erste Person bzw.

Organisation, die ein neues Produkt zur persöblichen oder ges chäftlichen Verwendung und nicht zur Verteilung oder zum

Wiederverkauf erwirbt).

Ansprüche im Rahmen dieser eingeschränkten Garantie

Jede Person, die einen Anspruch im Rahmen dieser eingeschränkten Garantie geltend macht, muss zur

Befriedigung von InFocus das Kaufdatum nachweisen und beweisen, dass das Produkt neu gekauft wurde. Die

Verkaufsquittung oder Verkaufsrechnung mit dem Kaufdatum des Produkts oder Zubehörs ist der Nachweis für das

Kaufdatum.

Inanspruchnahme von Garantieleistungen

Zur Inanspruchnahme von Leistungen während der Garantiezeit muss sich der Käufer zuerst mit 1) InFocus, 2)

einer von InFocus autorisierten Wartungsstätte oder 3) dem Händler, bei dem er das Produkt erworben hat, in Verbindung

setzen.

InFocus-Kundendienst – 1-800-799-9911 oder techsupport@infocus.com

Für den Erhalt von Dienstleistungen im Rahmen der Garantie muss der Käufer das fehlerhafte Produkt mit

vorausbezahlter Fracht und vorausbezahlten Gebühren an ein InFocus-Servicecenter oder eine von InFocus autorisierte

Wartungsstätte einsenden. Bei der Rücksendung des Produkts an InFocus ist eine sogenannte „Return-Material-

Authorization”- (RMA-) Nummer erforderlich, die gut leserlich auf der Außenseite des Originalkartons oder eines

ähnlichen Kartons, der einen gleichwertigen Schutz bietet, angebracht werden muss. InFocus oder die von InFocus

autorisierte Wartungsstätte wird das reparierte bzw. Ersetzte Produkt mit vorausbezahlter Fracht an den Käufer

zurücksenden.

Produkten, die für Garantieleistungen eingesendet werden, muss ein Schreiben beigefügt werden, das (i) das

Problem beschrebt, (ii) den Nachweis für das Kaufdatum ebthält, (iii) den Namen des Händlers enthält und (iv) das

Modell und die Seriennummer des Produkts angibt. Auf Anfrage von InFocus Corporation oder einem von InFocus

autorisierten Reparaturzentrum muss dem zu Garantiezwecken eingesandten Produkt ein Nackweis zur legalen Einfuhr

beigelegt werden; andernfalls muss das Produkt zu dem Händler, bei dem das Produkt gekauft wurde, oder zum

Hersteller (Käufer übernimmt sämtliche Steuern, Zölle und Frachtkosten) zurückgesandt werden, oder der Käufer muss

die Kosten für die Garantiereparatur übernehmen.

Durch eine Reparatur oder einen Austausch des Produkts oder Teilen davon wird die Garantiezeit des gesamten

Produkts nicht verlängert. Die Garantie für das reparierte Teil und die Herstellung gilt nur für eine Zeitdauer von neunzig

(90) Tagen nach der Reparatur bzw. Dem Austausch dieses Teils oder die restliche Zeitdauer der Produktgarantie, je

nachdem, welcher Zeitraum länger ist.

HAFTUNGSEINSCHRÄNKUNG

DIE HAFTUNG SEITENS INFOCUS, GLEICH OB VERTRAGSMÄSSIG, WEGEN UNERLAUBTER

HANDLUNG, UNTER EINER GARANTIE, AUS FAHRLÄSSIGKEIT ODER AUS ANDEREN GRÜNDEN,

ÜBERSCHREITET NICHT DIE RÜCKERSTATTUNG DES KAUFPREISES AN DEN KÄUFER. INFOCUS ÜBERNIMMT

AUF KEINEN FALL DIE HAFTUNG FÜR SPEZIELLE, MITTELBARE, NEBEN- ODER FOLGESCHÄDEN ODER

ENTGANGENEN GEWINN, UMSATZVERLUST ODER VERLUST VON ERSPARNISSEN. DER AUFGEFÜHRTE PREIS

FÜR DAS PRODUKT IST EIN FAKTOR BEI DER HAFTUNGSEINSCHRÄNKUNG SEITENS INFOCUS.

Rechtsbehelfsfrist – Keine Rechtshandlung, gleich welcher Art, die sich aus Einkaufsvereinbarung für das Produkt

ergibt, kann vom Käufer nach mehr als einem Jahr nach Entstehendes Klageanspruchs eingebracht werden.

Anwendbares Recht – Alle Rechtshandlungen, gleich welcher Art, die sich aus Einkaufsvereinbarung für das Produkt

ergeben, unterliegen den Gesetzen des US-Bundesstaates Oregon.

Zwangsschlichtung – Alle Rechtshandlungen, gleich welcher Art, die sich aus Einkaufsvereinbarung für das Produkt

ergeben, sind vorbehaltlich einer Zwangsschlichtung.

EINIGE

GERICHTSBARKEITEN

ERLAUBEN

KEINEN

HAFTUNGSAUSSCHLUSS

BZW.

KEINE

HAFTUNGSEINSCHRÄNKUNG FÜR NEBEM- ODER FOLGESCHÄDEN. IN DIESEM FALL TRIFFT DIE OBEN

AUFGEFÜHRTE EINDCHRÄNKUNG BZW. DER AUSSCHLUSS U.U. NICHT AUF SIE ZU. DIESE GARANTIE GIBT

IHNEN BESTIMMTE RECHTE. SIE KÖNNEN WEITERE RECHTE HABEN, DIE VIN DER GERICHTSBARKEIT

ABHÄNGIG SIND.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pelco Home Security System C2915M E 08 05 User Manual
Phase Technology Speaker SM500i User Manual
Philips Computer Monitor 107T40 User Manual
Philips Home Theater System HES2800 User Manual
Philips Stereo System FW320C User Manual
Pioneer DVD Player DV 210K K User Manual
Pioneer Stereo System VSX D411 User Manual
Planet Technology Switch WGSW 2620P User Manual
Poulan Snow Blower 424027 User Manual
Poulan Trimmer TE475 TE475Y User Manual