Model No. PFSB73930
Serial No.
USER’S MANUAL
The serial number is on a sign
behind the access panel. Write the
serial number in the space above.
Access
Panel
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our customer
hot line will provide immediate
assistance, free of charge.
CUSTOMER HOT LINE:
1-877-897-7493
Mon.–Fri., 8 a.m.–5 p.m. CST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING:
To reduce the risk of drowning, electric shock, or serious injury, read the fol-
lowing important precautions before using the hydrotherapy spa.
READ AND FOLLOW ALL INSTRUCTIONS
1. It is the responsibility of the owner to ensure
that all users of the hydrotherapy spa are
adequately informed of all precautions.
10. Never insert any object into any opening.
11. Do not use breakable containers in or near
the hydrotherapy spa.
2. Use the hydrotherapy spa only as described
in this manual.
12. Do not sit on the spa cover or place objects
on it; it is not designed to support weight.
3. The hydrotherapy spa is intended for home
use only. Do not use the spa in a commercial,
rental, or institutional setting.
13. Remove any water or debris that may collect
on the spa cover.
14. Keep children under the age of 12 and pets
away from the hydrotherapy spa when it is
not in use.
4. Use the hydrotherapy spa only on a level sur-
face. Do not use the spa on carpet or other
materials that could be damaged by moisture.
15. Keep all chemicals away from children and
pets.
5. The hydrotherapy spa will weigh approxi-
mately 3,300 pounds when it is filled with
water. Make sure that the location you select
for the spa will support this weight, plus the
weight of the occupants.
16. The pH and chemical balance of the water
must be maintained as explained in this man-
ual (see pages 11 and 16). Failure to do so
may cause injury to users or damage to the
hydrotherapy spa, and will void the warranty.
6. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
17. Individuals with infections and open sores or
wounds should not use the hydrotherapy
spa. Bacteria thrive in warm and hot water.
Always keep your spa disinfected and main-
tain the proper chemical balance.
7. DANGER—Risk of injury: Do not remove or
alter the covers on the suction fittings. Never
operate the hydrotherapy spa if the suction
guard is missing or broken. If you need to
replace a suction fitting or pump, make sure
you use only manufacturer recommended
replacement parts. Keep hair and body parts
away from the suction guard. Do not allow
long hair to float freely in the water; long hair
should be restrained with a bathing cap.
18. Shower before and after using the hydrother-
apy spa. This will remove any deodorant, per-
spiration, or body oils that could contaminate
the water. Showering after will remove any
residual chemicals and any bacteria that may
have been in the spa.
8. IMPORTANT: Do not allow the hydrotherapy
spa to be exposed to direct sunlight when it
is empty. The surface of the spa shell can
reach temperatures as high as 150°F in a mat-
ter of minutes if exposed to the sun while it is
empty. These high temperatures can cause
significant damage, such as blistering of the
shell surface and warping of the spa shell.
Any damage caused by sun exposure is not
covered under the warranty.
19. WARNING—The Ground Fault Circuit
Interrupter (GFCI), must be tested before
each use. To test the GFCI, press the “test”
button while the hydrotherapy spa is running.
The spa should shut off. Press the “reset”
button. The spa should resume normal opera-
tion. If the spa continues to run after the
“test” button is pressed, then the GFCI is
damaged. Do not use the spa until the GFCI
has been repaired or replaced by a qualified
electrician.
9. Do not bring any object into the hydrotherapy
spa that could damage the spa shell.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. DANGER—Risk of electric shock. Keep all
electrical appliances such as radios, tele-
phones, televisions, and lights at least five
feet away from the water.
physician before using the hydrotherapy spa.
Pregnant women should not use the spa if
the water temperature is above 100°F; the
unborn child could be seriously harmed. This
is especially important during the first 90
days of the pregnancy.
21. A wire connector is provided on the electron-
ics pack of the hydrotherapy spa to connect a
minimum No. 6 AWG (13.3 mm2) solid copper
conductor between the spa and any metal
equipment, electrical enclosure made of
metal, metal water pipes, or conduit within
five feet of the spa.
29. DANGER—To reduce the risk of drowning:
Prolonged immersion in the hydrotherapy spa
may cause hyperthermia. The causes, symp-
toms and effects of hyperthermia may be
described as follows: Hyperthermia occurs
when the internal temperature of the body
reaches a level several degrees above the
normal body temperature of 98.6°F. The symp-
toms of hyperthermia include an increase in
the internal temperature of the body, dizzi-
ness, lethargy, drowsiness and fainting. The
effects of hyperthermia include failure to per-
ceive heat; failure to recognize the need to
exit the spa or hot tub; unawareness of
impending hazard; fetal damage in pregnant
women; physical inability to exit the spa or
hot tub and unconsciousness resulting in
danger of drowning. WARNING: The use of
alcohol, drugs or medication can greatly
increase the risk of fatal hyperthermia.
22. DANGER—Risk of electric shock: Do not set
the hydrotherapy spa within five feet of any
metal objects or surfaces. As an alternative,
you may use the spa within five feet of metal
objects if each metal object is permanently
connected to the wire connector on the elec-
tronics pack of the spa by a minimum No. 6
AWG (13.3 mm2) solid copper conductor (see
instruction 21).
23. Do not operate the pump motor when the
hydrotherapy spa is empty. The pump motor
may be seriously damaged if it is operated
without water circulating.
24. DANGER—Risk of drowning: Exercise
extreme caution to prevent unauthorized and
unsupervised use of the hydrotherapy spa by
children. Children must always be supervised.
30. WARNING—To reduce the risk of drowning:
Do not use the hydrotherapy spa if you are
under the influence of alcohol or drugs. Heat
from the water, in conjunction with alcohol or
drugs, can cause loss of consciousness.
25. DANGER—To reduce the risk of drowning:
• Never use the hydrotherapy spa alone.
• Children should not use the spa unless they
are supervised by an adult.
31. WARNING—To reduce the risk of injury or
drowning: Consult your physician about pos-
sible side-effects of any medications you may
be taking before using the hydrotherapy spa.
Heat from the water, in conjunction with some
medications, may cause drowsiness and
increase the risk of drowning. Other medica-
tions can effect blood pressure, heart rate,
and circulation.
• Keep pets away from the spa at all times.
• Always replace and lock the spa cover when
the spa is not in use.
26. WARNING—To reduce the risk of injury: The
water temperature should never exceed
104°F. Temperatures between 100°F and 104°F
are considered to be safe for healthy adults.
However, if you plan to remain in the hydro-
therapy spa for more than 10 to 15 minutes, a
lower temperature is recommended. Lower
temperatures are also recommended for chil-
dren. Children should not be allowed to swim
under the surface of the water in the spa.
32. Do not use the hydrotherapy spa immediately
after strenuous exercise.
33. If you feel pain or dizziness at any time while
using the hydrotherapy spa, discontinue use
and contact a physician.
34. WARNING—To reduce the risk of injury: It is
especially important for persons over the age
of 35 or persons with pre-existing health
problems, such as obesity, heart disease,
high or low blood pressure, circulatory prob-
lems, or diabetes to consult their physician
before using the hydrotherapy spa.
27. WARNING—To reduce the risk of injury:
Before entering the hydrotherapy spa, always
use an accurate thermometer to determine
the water temperature.
28. WARNING—To reduce the risk of injury:
Pregnant women should consult with their
4
Download from Www.Somanuals.com. All Manuals Search And Download.
35. WARNING: The spa jets produce a stream of
water with relatively high pressure. Prolonged
exposure of a localized area of the body may
cause bruises to the skin.
36. The included warning sign must be posted
where all users of the hydrotherapy spa can
see and read it. (See POSTING THE WARNING
SIGN on page 2.)
37. WARNING DECAL PLACEMENT: Locate the
decals shown below and familiarize yourself
with the information on the decals.
WARNING:
Read all instructions before using the hydrotherapy spa. ICON assumes no
responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Congratulations for selecting the new PROFORM®
MAGNA hydrotherapy spa. The innovative MAGNA
spa allows you to enjoy all the benefits of hydrothera-
py in the comfort and privacy of your home.
For your benefit, read this manual carefully before
using the hydrotherapy spa. If you have questions
after reading the manual, please call our Customer
Service Department toll-free at 1-877-897-7493,
Monday through Friday, 8 a.m. until 5 p.m. Central
Time (excluding holidays). To help us assist you,
please mention the product model number and serial
Hydrotherapy is a proven method for soothing tired
muscles after exercise or for relieving the stress of a
busy life. The warm environment stimulates blood flow, number when calling. The model number is
which is essential in the healing process, and the
powerful massage action further eases tension and
stress throughout the body. The PROFORM MAGNA
hydrotherapy spa gives you the specialized treatment
you need to feel your best.
PFSB73930. The serial number can be found on a
decal on the access panel inside the spa (see the front
cover of this manual).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Air
Controls
Spa Shell
Jets
Jets
Waterfall
Console
Pillow
Air
Control
Pillow
Jets
Waterfall
valve
Filter
Access
Panel
Panel
Locking
Buckle
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Choosing a Location for the Hydrotherapy Spa
There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary
depending on whether you plan to use the spa inside or outside. We have listed several factors you may wish to
consider as you decide where to set up the spa.
If you set up the hydrotherapy spa inside:
If you set up the hydrotherapy spa outside:
1. The spa will increase the level of humidity in your
home. The location you choose should be well
ventilated. You may need to install a ventilation fan
or use a dehumidifier.
1. Check local building codes concerning the use of
outdoor spas.
2. The spa should be located near a power source
capable of supplying 240 volts AC power. It must
be wired directly into a grounded circuit with a
Ground Fault Circuit Interrupter (GFCI) capable of
carrying 45 amps. No other appliance should be
on the same circuit.
2. The spa should be located near a power source
capable of supplying 240 volts AC power. It must
be wired directly into a grounded circuit with a
Ground Fault Circuit Interrupter (GFCI) capable of
carrying 45 amps. No other appliance should be
on the same circuit.
3. The spa should be close to a source of water.
3. The spa should be close to a source of water.
4. We recommend that you place the spa on a water-
and stain-resistant, non-slip surface. Do not use
the spa on rough or sharp surfaces such as gravel
or wood chips.
4. Do not use the spa on carpet or other material that
may be damaged by moisture. We recommend
that you place the spa on a water- and stain-resis-
tant, non-slip surface with a floor drain for any
water that may splash from the spa.
5. Make sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 3,300
pounds when it is filled with water.
5. Make sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 3,300
pounds when it is filled with water.
6. Consider environmental factors such as rain, wind,
shade, and sunlight.
6. Do not use the spa above a finished living area,
due to the risk of water damage.
7. You should be able to monitor the use of the spa
from your home, to prevent unauthorized use by
children. You may want to enclose the spa with a
fence and self-latching gate to prevent unautho-
rized use.
7. Make sure that there is room around the spa to
permit servicing of the unit. The dimensions of the
spa are 84” W x 84” L x 36” H. You should allow for
this size when choosing the location.
8. Make sure that there is room around the spa to
permit servicing of the unit. The dimensions of the
spa are 84” W x 84” L x 36” H. You should allow for
this size when choosing the location.
8. The spa is not designed for in-floor installation.
However, it is compatible with a deck system that
is built flush with the top of the spa, provided you
leave access to the motor for service.
9. The spa is not designed to be installed below
ground level. However, it is compatible with a deck
system that is built flush with the top of the spa,
provided you leave access to the motor for ser-
vice.
9. Make sure to note any other considerations, such
as aesthetics or privacy concerns, that may affect
the safety or enjoyment of using the spa.
10.Make sure to note any other considerations, such
as aesthetics or privacy concerns, that may affect
the safety or enjoyment of using the spa.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Before beginning assembly, carefully read the
following information and instructions:
ASSEMBLY REQUIRES THE FOLLOWING
TOOLS (not included):
• Place all parts in a cleared area and remove the
packing materials from the spa shell. Do not dis-
pose of the packing materials until assembly is
completed and the spa is operating.
• One phillips screwdriver
A wire connector is provided on the electronics
pack of the spa to connect a minimum No. 6
AWG (13.3 mm2) solid copper conductor
• During assembly, make sure that all parts are
oriented as shown in the drawings.
between the spa and any metal equipment,
electrical enclosure made of metal, metal water
pipes, or conduit within five feet of the spa.
• Read each assembly step before you begin.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before beginning assembly, make sure that you
have read and understand the information in the
above and on the previous two pages.
1
Spa Shell
Remove the four #10 x 2” Machine Screws (46) that
secure the indicated Access Panel (25) to the spa.
Carefully remove the Access Panel and set it aside.
Be careful not to damage the spa shell.
46
25
46
2. Close the valve knob on the drain hose. Thread the
cap onto the drain hose.
2
Locate the four gate valves inside the access open-
ing (there are two gate valves per pump). Make sure
that the gate valves are open and that the locking
clips are snapped onto the stems of the gate valves,
as shown in the inset drawing.
Gate Valve
Make sure that the six collars are tightened (there
are two collars per pump and two on the heater).
Drain
Hose
Refer to step 1. Re-attach the Access Panel (25) to
the spa.
Locking Clip
Collar
Cap
Valve
Knob
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert the pillow (47) into the lounge seat recepta-
cle. The pillow can be rotated 180º to change
between the high or low positions.
3
47
4. The hydrotherapy spa operates on a 240 volt power source and must be wired directly to a 240 volt Ground
Fault Circuit Interrupter (GFCI) installed in your home. This procedure must be performed by a qualified,
licensed electrician. A wiring diagram is found on the inside of the electronics package for reference.
Under no circumstances should the spa be wired by someone other than a qualified electrician. Before
you have the spa wired, make sure it is in the desired position, and that it can be easily serviced, if needed.
5. Make sure that a qualified electrician has wired the
5
3
spa to a 240 volt power source.
22
21
Fill to here
Remove the two warning decals (see page 5) from
the spa shell. Using a damp cloth, wipe the spa shell
clean. Before filling the spa, make sure that it is
in the desired position and that there is room to
easily service it. Once the spa is filled, it will
have to be drained before it can be moved.
16
5
Insert a garden hose into the filter housing, and
begin filling the spa. Do not use soft water. The
spa may be filled with cold water; however, if warm
or hot water is used, the spa will be ready for use
sooner. Fill the spa until the water is at the level of
the molded fill line. Do not overfill the spa.
Garden
Hose
Refer to the inset drawing. Set the Filter (5), Filter
Plug (16), Diverter (21), and Basket (22) into the fil-
ter housing. Next, screw the Filter Cover (3) into the
filter housing until it is fully seated.
6. Pull down one of the straps on the Spa Cover (11)
and hold the Buckle (26) against one of the panels
on the spa. (Note: To position the Buckle correctly,
have a second person hold the strap on the opposite
side of the Spa Cover snug.) The Spa Cover must
be snug. Do not place the Buckle over the
grooves between the premium cedar panels.
Refer to the inset drawing. Remove the latch from
the Buckle (26). Attach the Buckle to the panel with
two #4 x 3/4” Screws (27).
6
Strap
11
Latch
26
27
Attach the other three Buckles (26) to the panels in
the same way.
Strap
Remove the Spa Cover (11) from the spa.
26
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Hydrotherapy Spa
The hydrotherapy spa is designed to seat seven
adults. The spa holds approximately 375 gallons of
water and offers a heating system (80°F to 104°F), a
filtration system, and adjustable hydrotherapy jets.
Follow the guidelines below to use and maintain the
spa for your long-term enjoyment.
4. Turn the power on. The spa will begin an auto-
matic priming sequence.
A countdown from “005” to “000” will appear in the
display of the console.
Once the countdown has reached “000,” “Pr” will
be displayed. “Pr” indicates that the controller is in
the two-pump priming mode. This mode will last
for four to five minutes.
WIRING THE HYDROTHERAPY SPA
The hydrotherapy spa is designed to operate with a
240 volt AC power source. It must be wired directly
into a grounded circuit with a Ground Fault Circuit
Interrupter (GFCI) capable of carrying 45 amps. No
other appliance should be on the same circuit. Test
the GFCI before connecting the power cord to the
spa. Connection of the spa to the 240 volt power
source must be performed by a qualified, licensed
electrician and must comply with all local, state,
and federal electrical codes. Please refer to the
instructions on the inside of the controller for informa-
tion about connecting the spa to a 240 volt power
source.
5. As soon as “Pr” is displayed, push pump button 1
once to start the pump on low speed and then
push the button again to switch to high speed.
Repeat for pump button 2.
If water is not flowing from the jets after two min-
utes, turn the power off. Important: Do not allow
the pumps to run without priming for more than
two minutes. Under no circumstances allow a
pump to run without priming beyond the end
of the four to five minute priming mode. Doing
so may cause damage to the pump and cause the
spa to go into an overheat condition.
Once the spa is filled with water, the power can be
turned on. Note: If this is the first time the spa has
been turned on, or if the pumps have been
drained, the pumps must be primed before the
spa can be used.
Repeat the process of venting the air from the
pumps and the controller and priming the pumps
until water flows from the jets.
PRIMING THE PUMPS
6. When the priming sequence is completed, the spa
will automatically return to the normal heating and
filtering mode. During the priming process, the
heater is disabled to allow the pumps to be primed
without activating the heater under low flow or no
flow conditions.
To prime the pumps, follow the steps below.
1. Remove the access panel (see ATTACHING AND
REMOVING THE ACCESS PANEL on page 17).
2. Make sure all of the valves in the plumbing system
are open to allow as much air as possible to
escape from the plumbing and the controller dur-
ing the filling process. Fill the spa to the level
shown in step 5 on page 9. Use towels to soak up
any water that leaks from the plumbing and pumps
during the priming process.
Once the pumps are primed, push pump button 1
and pump button 2 to turn the pumps off.
7. The console will display “100F” and then “--F,” for
approximately one minute. The spa requires one
minute of water flowing through the heater to
determine the water temperature.
3. Loosen the indi-
cated collar on
Loosen this
one of the pumps
Collar
to vent the air
from the pump.
Repeat for the
other pump.
Allow a small
amount of water
and air to escape from the pumps and related
plumbing. Then, retighten the collars.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
8. After one minute, the current temperature of the
water will be displayed. Push the temperature up
or down button to set the temperature of the
water. If the water temperature is below the set
temperature, the heat indicator light will turn on to
show that the water is now being heated.
Once you have tested the GFCI, verify that water is
flowing from the jets. Set the air controls to the lowest
setting (see USING THE CONTROLS on page 13).
Cover the hydrotherapy spa with the spa cover. The
spa cover must be tight (see SECURING THE SPA
COVER ON THE SPA on this page). The water will
heat at about 6°F per hour with the cover on. If you
are using the spa indoors, and the room temperature
is maintained at 70°F, it will take approximately 6 to 8
hours for the water to reach the set temperature.
The controller will automatically heat the water
and all of the features of the console will be avail-
able. To use the console, see USING THE CON-
TROLS on page 13
The temperature and the water flow can be set or
changed with the controls on the console (see USING
THE CONTROLS on page 13).
9. Remove the towels and re-attach the access
panel (see ATTACHING AND REMOVING THE
ACCESS Panel on page 17).
SECURING THE SPA COVER ON THE SPA
TESTING AND TREATING THE WATER
To secure the spa cover,
snap the latches on the
The first time you use the spa, you should test and
treat the water. You must also treat the water each
time you refill the spa. A test strip and a chemical
pack are available at your local pool and spa store.
Follow the directions carefully on the chemical pack to
test and treat the water. Always keep the chemicals
away from children and pets.
spa cover into the buckles
on the panels. To lock the
buckles, insert the key and
turn it clockwise 1/4 turn.
To unlock the buckles,
insert the key and turn it
counterclockwise 1/4 turn.
Always keep the buckles
locked when the spa is
not in use. Keep the
Latch
Key
See WATER CHEMISTRY on page 16 for information
concerning proper water maintenance.
Buckle
STARTING THE HYDROTHERAPY SPA
keys in a safe place, out
of the reach of children.
You should always test the GFCI before using the
hydrotherapy spa. First, turn on the spa. Press the jet
button on the console (see USING THE CONTROLS
on page 12). Once the spa is running, press the GFCI
“test” button. The spa should shut off. Press the
“reset” button. The spa should resume normal opera-
tion. If the spa continues to run after the “test” button
is pressed, the GFCI is damaged. Do not use the spa
until the GFCI has been repaired or replaced by a
qualified electrician.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Spa Shell Diagram
J
P
M
K
K
K
J
K
M
M
L
L
C
L
L
K
N
Q
I
C
C
K
C
D
B
F
L
G
C
C
L
H
K
I
E
O
P
K
L
A
A. The filter can be removed for cleaning or replace-
ment (see CHECKING AND CLEANING THE FIL-
TER on page 15).
H. The console controls the jets, turns the underwater
light on and off, and adjusts the water temperature
(see USING THE CONTROLS on page 13).
B. The underwater light can be used for night opera-
tion (see USING THE CONTROLS on page 13).
The spa includes both red and blue covers for the
light.
I. The four air controls regulate the air flow to the
whirlpool, hydrotherapy, and volcano jets.
J. The two neck jets can be adjusted to spray sooth-
ing water on your neck.
C. The ten air injectors create air bubbles that
enhance the hydrotherapy experience.
K. The twenty rotary jets provide a spinning mas-
sage.
D. The volcano jet provides a soothing foot massage.
L. The nine dual rotary jets provide a pulsating mas-
sage action. Rotate the outer ring counterclockwise
to turn the jets on. Rotate the outer ring clockwise
to turn the jets off.
E. The whirlpool jet diverts the water flow four differ-
ent ways. By turning the outer ring, you can divert
the water flow between the volcano jet (D), the
other jets on the spa, and the whirlpool jet (E),
which creates a whirlpool action. Note: The outer
ring may be hard to turn while the pump is
turned on high.
M. The three variable-flow jets are fully adjustable.
Turn the outer rings to regulate the flow.
N. The power massage jet provides a soothing mas-
sage to your lower back. Turn the outer ring to reg-
ulate the flow.
F. The four suction fittings provide water to the
pumps. The suction covers should always be in
place over the fittings. Never operate the spa with-
out the suction covers in place.
O. The skimmer cleans the surface of the water.
G. An optional ozone generator can be purchased and
installed to utilize the ozone jet. Ozone helps sani-
tize the spa with minimal chemical treatment.
P. The waterfall provides a soothing sound and mas-
sage.
Q. The waterfall valve turns the waterfall off and on.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Controls
Air Controls
1, 2, and 3
Air Control 4
Blower
Button
Mode
Button
Display
Pump
Button 1 Button 2
Pump
Light
Button
Temperature
Buttons
current only when pump 1 has been operating for two
minutes. “STD” displays momentarily when standard
mode is selected.
2
• Economy Mode heats the spa to the set tempera-
ture only during the filter cycles. “ECO” is displayed
when the temperature is not current and alternates
with the temperature when the temperature is cur-
rent.
1
2
3
6
1
6
3
1
6
4
6
6
• Sleep Mode heats the spa to within 20°F of the set
temperature during the filter cycles only. “SLP” is
always displayed when the temperature is not cur-
rent, and alternates with the temperature when the
temperature is current.
1
3
4
4
Air Control 1 determines the amount of air flowing
through the hydrotherapy jets labeled 1 in the drawing
above. If the control is turned counterclockwise, the
amount of air will increase; if the control is turned
clockwise, the amount of air will decrease. Air controls
2, 3, and 4 function in the same manner.
Pump Button 1 controls the spa jets labeled 3 and 4
in the drawing at the left. If the button is pressed
once, the jets will run, providing gentle hydrotherapy.
If the button is pressed again, the jets will shut off.
Pump Button 2 controls the spa jets labeled 1 and 2
in the drawing at the left. If the button is pressed
once, the jets will run, providing soothing hydrothera-
py. If the button is pressed again, the jets will shut off.
The spa also features an automatic mode that heats
and filters the water when the spa is left unattended.
When the power to the spa is first turned on, or if the
water temperature is below the set temperature, the
water will be heated as required. Note: To keep the
filter and heat cycles from running, the power to
the spa must be turned off.
Air Controls 2, 3, and 4 determine the amount of air
flowing through the hydrotherapy jets labeled 2, 3,
and 4 in the drawing above.
The Mode Button switches the console between
Standard, Economy, and Sleep modes.
• Standard Mode maintains the desired temperature.
Note: The last measured temperature displayed is
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Light Button turns the underwater light on and
off.
20°F cooler than the set temperature. When this hap-
pens, the heater will automatically activate to warm the
water. The word “ICE” will appear in the display if the
temperature drops below 40°F. If this happens, the
pump will automatically circulate the water and warm
the plumbing to keep the water from freezing.
The Temperature Buttons control the temperature set-
ting of the water. The temperature setting can be from
80°F to 104°F. The water heats at about 6°F per hour
with the cover on. Use a medical or other accurate
thermometer to check the temperature of the water.
Note: The word “COOL” will appear in the console
display if the temperature of the water is more than
The Blower Button turns the ten air injectors, labeled
6 in the small drawing on page 13, on and off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
The hydrotherapy spa is designed to provide years of
enjoyment. Please follow the guidelines below to
properly maintain your spa.
MAINTAINING THE SPA COVER
The spa cover should be cleaned monthly. To clean
the spa cover, use water and a non-abrasive cleaner
on the entire cover. Rinse the cover with a garden
hose to remove any cleaner residue. Dry the cover
entirely. Use a non-silicone-based vinyl conditioner on
the cover after you clean it. This will help protect the
cover from sun damage.
MAINTENANCE SCHEDULE
Daily
• Check the water level and refill the spa to the level
shown in step 5 on page 9.
• Check the pH balance and sanitizer level. Make
adjustments if necessary (see WATER CHEM-
ISTRY on page 16).
CHECKING AND CLEANING THE FILTER
The filter should be checked periodically for build-up
of dirt and oil. If the filter needs to be cleaned, follow
the steps below:
Weekly
• Clean the spa shell at the waterline.
• Check and thoroughly clean the filter (see CHECK-
ING AND CLEANING THE FILTER on this page).
• Replace the filter if needed (see ORDERING
REPLACEMENT PARTS on the back cover of this
manual).
1. Turn off the power.
2. Unscrew the filter
Filter
cover.
Cover
4. Lift the the filter out
Basket
of the filter housing.
Monthly
5. Check the filter for
Diverter
• Clean the spa cover (see MAINTAINING THE SPA
COVER on this page).
dirt and debris. If the
Filter
filter needs to be
Plug
• Soak the filter for two hours in a trisodium phos-
phate (TSP) solution. Rinse the filter in clean water.
• Replace the filter if needed (see ORDERING
REPLACEMENT PARTS on the back cover of this
manual).
cleaned, rinse the fil-
Filter
ter with a hose. If the
filter is still dirty, soak
it in cleaning solution
from a pool and spa
supply store.
Filter
Housing
Every Three Months
• Drain the spa and refill it with clean water. Sanitize
and test the pH of the water.
• Check for any leaks around the pump or joints in
the pipes. The seals will wear out over time; detect-
ing leaks early can reduce repair costs.
• Clean the interior of the spa. Do not use solvents or
waxes.
6. Inspect the filter for
damage. Replace
the filter if it is dam-
aged.
7. Insert the cleaned or
new filter into the fil-
ter housing.
8. Re-attach the filter cover.
MAINTAINING THE SPA EXTERIOR
The surround is maintenance free. The surround
should be cleaned with a mild soap solution; do not
use solvents or waxes.
CLEANING THE SPA SHELL
The spa shell should be cleaned with a mild soap
solution; do not use solvents or waxes. The spa
should always be clean and dry before being moved
or stored.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER CHEMISTRY
To maintain the proper pH level, test the pH of the
water regularly. To test the water, purchase a pH test
kit at a pool and spa supply store. The pH reading
should be between 7.2 and 7.8. If the level is too low,
add a pH increaser (usually soda ash). If the level is
too high, add a pH reducer (usually sodium bisulfate).
Test the water again after five minutes. See the
instructions with your pH test kit for additional infor-
mation about testing and adjusting the pH.
Maintaining the pH level of the water is very important
to the operation of the spa. To maintain the proper pH
level and to sanitize the spa, you can purchase a
chemical starter kit from your local pool and spa sup-
ply store.
CAUTION: The chemicals used to maintain the pH
balance of the water and to sanitize the water can
be dangerous. Always follow these basic guide-
lines when handling the chemicals:
SANITIZING THE HYDROTHERAPY SPA
1. Always read and follow the directions on the
label, unless directed otherwise.
2. Never mix different chemicals.
3. Do not exceed the recommended amounts of
chemicals—follow the directions on the label.
4. Keep all chemicals out of the reach of children
and pets.
The most common sanitizing agent is a solid bromine
concentrate. The amount required varies according to
several factors, such as user load, temperature, and
water conditions. Proper water maintenance is a com-
plex process. Contact your local pool and spa supplier
for information concerning which chemicals you
should use in your area to sanitize the spa.
5. Keep all containers closed tightly when not in
use.
CHANGING THE FILTER CYCLE
6. Never add water to the chemicals—always add
the chemicals to the water as directed.
7. Always store chemicals in a cool, dry place.
The spa will filter the water every 12 hours. The dura-
tion of the cycle can be adjusted to last 2, 4, 6, or 8
hours or run indefinitely. Press the temperature up or
temperature down button on the console. When the
display begins to flash, press pump button 1. The dis-
play will read “F2.” To change the time, press the
temp up button until the desired time is reached.
Press pump button 2 to confirm the selection.
MAINTAINING THE PROPER PH BALANCE
The pH factor is a measure of the relative acidity or
alkalinity in the water, and is measured on a scale of
1 to 14. Pure water has a value of 7, which is neutral.
Any value above 7 is alkaline, and any value below 7
is acidic. You should maintain a slightly alkaline pH
level, between 7.2 and 7.8, in the hydrotherapy spa.
Pump 2 purges for five minutes and the blower
purges for 30 seconds at the beginning of each filter
cycle. Pump 1 will run on low during filtration and the
ozone generator will be enabled.
Severe problems can occur when the pH balance is
not maintained within this range. If the pH level
exceeds 7.8, dissolved minerals can build up and clog
the plumbing in the spa jet unit. If the pH level falls
below 7.2, the acid level in the water will begin to cor-
rode the metal parts in the spa jet unit. Also, the sani-
tation agents in the water will not be effective if the pH
level is not properly maintained. Damage caused by
improper pH levels is not covered under the warranty.
As spa usage increases, the duration of the filter
cycle may need to be increased.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING AND REMOVING THE ACCESS PANEL
1. Using the console, adjust the temperature to the
lowest setting.
2. Shut off the power to the spa, at the circuit break-
er or GFCI.
3. Remove the access panel from the spa (see
ATTACHING AND REMOVING THE ACCESS
PANEL on this page).
Turn off the spa power. To remove the indicated
Access Panel (25), remove the four #10 x 2” Machine
Screws (46) that secure the Access Panel to the spa.
Carefully remove the Access Panel and set it aside.
4. Pull the hose out and hold it above the waterline.
Remove the cap, open the valve knob, and attach
a garden hose to the drain hose. Lower the hose
and drain the spa.
46
25
46
To replace the Access Panel, hold the Access Panel
in place and secure it with the four #10 x 2” Machine
Screws (46). Be careful not to overtighten the
Screws.
Cap
Drain
Hose
Valve
Knob
DRAINING THE HYDROTHERAPY SPA
The hydrotherapy spa should be drained at least four
times per year and refilled with clean water. You may
need to drain the spa more often, depending on the
user load. This must be done because after repeated
chemical treatment the water becomes chemically
saturated. Once this happens, additional chemical
treatment of the water is no longer effective. The spa
should also be drained if you will not be using it for
long periods of time. The spa must always be drained
before major repairs are made.
5. When the spa is empty, remove the garden hose,
close the valve knob, and re-attach the cap and
return the drain hose inside the spa.
6. Re-attach the access panel.
7. Refill the spa and treat the water with chemicals
(see pages 11 and 16).
The hydrotherapy spa should always be covered
when it is empty. Direct sunlight can cause exten-
sive damage. The surface of the spa shell can
reach temperatures as high as 150°F in a matter
of minutes if exposed to the sun while it is empty.
These high temperatures can cause significant
damage, such as blistering of the shell surface
and warping of the spa shell. Any damage caused
by sun exposure is not covered under warranty.
To drain the hydrotherapy spa, follow the steps below:
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAINING THE PUMPS
REPLACING THE LED LIGHT
After the hydrotherapy spa is drained, the jet pumps
should also be drained if the spa will be stored for
more than thirty days or if it may be exposed to freez-
ing temperatures.
If the underwater light burns out, you will need to
remove the access panel to replace it (see ATTACHING
AND REMOVING THE ACCESS PANEL on page 17).
Make sure the spa power is turned off. Next, locate the
light housing. Turn the light housing counterclockwise
and remove it from the spa shell.
Turn off the power to
the spa. To drain the jet
pumps, remove the
Light Housing
LED
access panel from the
spa (see ATTACHING
AND REMOVING THE
ACCESS PANEL on
page 17). Locate the jet
pumps inside the spa.
Loosen the indicated
collar on each of the
pumps.
Light
Collar
Light
Housing
WINTER USE AND CARE
To replace the LED light, pull the old LED light out of
the housing and insert a new LED light. Re-attach the
light housing to the spa shell. Re-attach the access
panel to the spa.
The hydrotherapy spa is designed for year-round use.
If you decide to store the spa for the winter, store it in
a warm, dry location. Follow the steps below to winter-
ize the spa.
1. Make sure the power to the spa is turned off.
2. Drain the spa (see DRAINING THE HYDROTHER-
APY SPA on page 17).
3. Remove all remaining water from the spa shell. Dry
the spa shell with towels.
4. Set the air controls to the lowest setting. Use a
wet/dry vacuum to pull any remaining water from
the system. To do this, place the vacuum nozzle
over each jet, starting with the highest jet and fin-
ishing with the lowest jet.
5. Set the air controls to the highest setting and
repeat step 3.
6. Drain the pumps (see DRAINING THE PUMPS on
this page). Once the water is drained from the
pumps, place the vacuum nozzle over the drainage
hole in the pumps and vacuum any additional
water from the pumps. Note: For additional pro-
tection, remove the pumps/motors from the spa
and store them in a climate-controlled room.
7. Clean the spa shell (see page 15).
8. Clean the filter (see page 15).
9. Shut the power off at the breaker. Label the
breaker in such a way that the breaker will not
be turned on accidentally.
10. Re-attach the access panel and the spa cover.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Most problems can be solved by following the simple steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at
1-877-897-7493, Monday through Friday, 8 a.m. until 5 p.m. Central Time.
1. SYMPTOM: THE SPA WILL NOT OPERATE
6. SYMPTOM: THE WATER DOES NOT HEAT
a. Check to see if the GFCI breaker is tripped or
was not turned on. Reset the GFCI breaker.
a. Make sure that the hydrotherapy spa is fully
covered with the spa cover. The spa cover
must be tight for the water to heat. Set the
air control to low. The water will heat at a rate
of 6°F per hour. If you are using the spa
2. SYMPTOM: THE CIRCUIT BREAKER OR THE
GFCI TRIPS WHILE THE SPA IS OPERATING
indoors and the room temperature is main-
tained at 70°F, it will take approximately 6 to 8
hours for the water to reach the set temperature.
a. Reset the circuit breaker or the GFCI. If the cir-
cuit breaker or the GFCI trips again, contact a
qualified electrician for service.
b. If you are using the hydrotherapy spa outdoors,
it may take longer for the water to heat. See
the chart below for the approximate heating
time.
3. SYMPTOM: THE PUMP HUMS
a. The filter may be dirty or damaged. Remove
the filter from the filter housing and clean or
replace the filter (see page 15).
Air Temperature
70°F +
Heating Time
6 to 8 hours
b. The pump may have a foreign object stuck in
the impeller. Contact our customer service
department.
50°F to 70°F
30°F to 50°F
9 to 11 hours
12 to 14 hours
b. If the water still has not heated after four days,
contact our customer service department.
c. The pump may have a loose wire connection.
Contact our customer service department.
7. SYMPTOM: THE WATER IS NOT BEING
CLEANED BY THE FILTER
4. SYMPTOM: THE PUMP HUMS, BUT DOES NOT
ROTATE
a. Check to see if the filter are in place. Clean the
filter if they are dirty.
a. The pump may be jammed. Contact our cus-
tomer service department. If your spa is no
longer under warranty, contact a local spa and
pool service provider.
b. Check the chemical balance of the water. If the
pH is incorrect, the sanitizing agents will not
function properly. See the section on maintain-
ing the proper pH balance on page 16.
5. SYMPTOM: THE PUMP IS NOISY WHILE
OPERATING
8. SYMPTOM: THE WATER PULSATES OR
THERE IS MINIMUM WATER FLOW
a. There may be debris in the pump. Contact our
customer service department.
a. This usually occurs only when the water level is
low. Add water until it is 2” to 4” above the
skimmer basket.
b. The pump may have a bad bearing. Contact
our customer service department.
b. The filter cover may not be tight. Make sure the
filter cover is tight.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
9. SYMPTOM: THE WATER LEVEL DROPS
11. SYMPTOM: THE CONSOLE DISPLAYS “OHH,”
“ICE,” “CLD,” “SNA,” “SNB,” “SNS,” “HFL,”
“LF,” “DR,” or “DRY”
a. A clamp or seal inside the pump compartment
may be loose. Check inside the pump compart-
ment for excess water and watch the pump unit
while it is operating to see if water drips from
any of the plumbing. If you can identify the
location of the leak inside of the spa jet unit,
tighten the clamp or replace the damaged seal.
a. If the console displays one of the messages
listed above, or if the console does not function
correctly, please call our Customer Service
Department toll-free at 1-877-897-7493,
Monday through Friday, 8 a.m. until 5 p.m.
Central Time (excluding holidays).
b. Some water loss due to evaporation is normal.
If rapid water loss occurs, or if you notice wet-
ness on the floor around the hydrotherapy spa,
the spa shell may have a leak. Contact your
local pool and spa service provider for repairs.
10. SYMPTOM: THE SPA JET UNIT CONTINUES
TO RUN AFTER IT HAS BEEN SHUT OFF
a. To turn off the main jets, press pump button 1
once or twice. Note: If the actual temperature
of the water in the spa is below the set temper-
ature, or if the spa is running a filter cycle, the
heater pump/motor will not shut off.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Part List—Model No. PFSB73930
R0303A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
2
1
8
1
2
1
1
4
1
1
9
4
1
3
1
4
4
1
1
1
1
8
1
1
4
8
10
1
1
14
1
3
2
1
Console With Overlay
3-wire Power Cord
Filter Cover
Rubber Washer
Filter
Rubber Isolator
Blue Light Cover
Red Light Cover
#10 x 1 1/2” Sheet Metal Screw
2-speed Pump*
Spa Cover
Dual Rotary Jet Face
Jet Pump/Motor O-ring
Controller*
Medium Jet Housing
Cartridge Plug
Suction Cover Assembly
Air Control Knob
1-speed Pump*
4-wire Power Cord
Diverter
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
#
3
21
1
1
1
22
1
21
3
2
32
2
2
4
2
1
9
2
2
10
1
Nozzle Housing
Small Rotator
Large Rotary Jet
Face Ring
Small Nozzle
Jet Ring
Nozzle Bushing
Pivot Ring
Medium Nozzle
Drain Plug
#10 x 2” Machine Screw
Pillow
Drain Plug O-ring
Corner Panel
Neck Jet
Filter Housing*
Dual Rotary Jet
Heater Gasket
Waterfall Valve
Air Injector Assembly
Blower
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Basket
2
2
1
1
1
1
Ground Wire
Key
User’s Manual
Large Warning Sign
Warning Sign
LED Light
1/4” Lock Washer
Filter Housing Door
Access Panel
#
#
#
#
Buckle
#4 x 3/4” Screw
1/4” x 1 1/2” Screw
Overlay
Whirlpool Jet
1/4” Washer
Face Plate Assembly
Panel
Heater Collar With Screw
Volcano Jet
#
* Indicates a part that is serviceable only by service
technicians.
# Indicates a non-illustrated part.
Specifications are subject to change without notice.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded Drawing—Model No. PFSB73930
R0303A
28
10*
13
23
31
23
31
11
4
13
28
13
19*
48
3
23
31
23
31
45
22
16
6
21
4
56
13
28
31
5
48
45
9
31
24
28
31
6
51*
9
31
53
29
32
34
55
9
1
14*
26
18
50
47
50
18
31
9
31
34
27
53
54
40
54
39
41
42
37
43
46
41
15
44
36
30
35
25
46
33
46
8
7
38
46
49
12
20
2
17
17
2
52
17
17
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-877-897-7493, Monday
through Friday, 8 a.m. until 5 p.m. Central Time (excluding holidays). To help us assist you, please be prepared
to give the following information when calling:
• The MODEL NUMBER of the product (PFSB73930)
• The NAME of the product (PROFORM MAGNA hydrotherapy spa)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on
pages 22 and 23)
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. ICON
extends a limited five (5) year warranty on the spa shell structure. ICON extends a limited two (2) year war-
ranty on the pump, motor, and electronics package. This warranty extends only to the original purchaser.
ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through
one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized
by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage, or repairs not provided by ICON authorized ser-
vice personnel; to products used for commercial or rental purposes; or to products used as store display mod-
els. Specifically excluded are damages caused by or attributable to the following incidents: any damage to the
premium cedar surround or frame attributable to improper handling or freight damage; damage resulting from
improper winterization; damage to the spa shell resulting from improper chemical treatment, damage to the
spa shell resulting from exposure to extreme temperatures, or damage to the spa shell resulting from expo-
sure to direct sunlight and ultraviolet rays while the spa is empty; damage to the pump, motor, plumbing, and
components due to improper maintenance, chemical treatment, or exposure; or damage resulting from failure
to properly follow user’s manual installation, operating, or maintenance instructions. Also excluded are con-
sumable components, including but not restricted to filter cartridges. No other warranty beyond that specifi-
cally set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of or damage
to property including water damage, loss of revenues or profits, loss of enjoyment or use, costs of removal,
installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or
limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 195331 R0303A
Printed in USA © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|