¨
Model No. PFBE30790
Serial No.
Write the serial number in the
space above for reference.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find that there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile PROFORM¨ 738
weight bench. The PROFORM¨ 738 offers a selection
of weight stations designed to develop every major
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please note
muscle group of the body. Whether your goal is to tone the product model number and serial number before
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the PROFORM¨
738 will help you to achieve the results you want.
calling. The model number is PFBE30790. The serial
number can be found on a decal attached to the PRO-
FORM¨ 738 (see the front cover of this manual).
For your benefit, read this manual carefully before
using the PROFORM¨ 738. If you have additional
questions, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Lock Pin
Seat
Weight Rest
Preacher
Curl Pad
Adjustment Bar
Backrest
Preacher Curl
Weight Rest
Adjustment
Bracket
Leg Lever
Weight
Tube
The decal shown at the right has been applied to the weight
bench in the indicated location. If the decal is missing, or if it
is not legible, please call our Customer Service Department
at 1-800-999-3756 to order a free replacement decal.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.
¥ Place all parts of the weight bench in a cleared
area and remove the packing materials; do not
dispose of the packing materials until assembly is
completed.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
¥ Two (2) adjustable wrenches
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ One (1) rubber mallet
¥ For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the center of this manual.
Note: Some small parts may have been pre-
attached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.
¥ Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
¥ As you assemble the weight bench, be sure that
all parts are oriented as shown in the drawings.
1. Before beginning assembly, be sure that you
have read and understand the information in
the box above.
1
24
14
Press a 76mm Plastic Bushing (14) into the top of
the Frame (4). Press two 76mm Slotted Endcaps
(16) into the bottom of the Frame. Press a 50mm x
70mm Outer Cap (43) onto the lower end of the
Frame. Press a 50mm Square Endcap (24) into
the back of the Frame.
4
43
16
2. Locate the Stabilizer (3) that has a warning decal
on it. Turn the Stabilizer so the decal is on top and
insert the Stabilizer into the Frame (4) as shown.
Refer to the inset drawing and align the indicated
holes.
2
4
35
35
Decal
3
34
Insert two M10 x 85mm Carriage Bolts (25) up
through the Frame (4) and the Stabilizer (3).
Thread an M10 Nylon Locknut (35) with a 10mm
Washer (34) onto each Bolt. Do not tighten the
Nylon Locknuts yet. Next, attach the Stabilizer to
the Frame with an M10 x 70mm Bolt (31), two
10mm Washers (34), and an M10 Nylon Locknut
(35) as shown. Do not tighten the Nylon
Locknut yet.
34
31
3
4
25
Align these
Holes
Attach the other Stabilizer (not shown) to the
Frame (4) in the same way.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Identify the Right Upright (2) by noting the posi-
tions of the adjustment brackets and the bolt
holes near the lower end. Attach the Right
Upright to the indicated Stabilizer (3) with two
M10 x 95mm Bolts (49), two 10mm Washers
(34), and two 15mm x 70mm Spacers (39). Do
not tighten the Bolts yet.
3
Adjustment
Brackets
2
Bolt
Holes
34
3
Press a 76mm Slotted Endcap (16) into the bot-
tom of the Right Upright (2); it may be necessary
to turn the Slotted Endcap so it fits around the
15mm x 70mm Spacers (39).
49
39
16
Attach the Left Upright (not shown) to the other
Stabilizer (not shown) in the same manner.
4
4. Insert the Right Barbell Lock Pin (38) through
the welded tube on a Weight Rest (1). Tighten
an M10 Nylon Locknut (35) onto the Right
Barbell Lock Pin.
38
28
35
1
Attach the Left Barbell Lock Pin (28) to the other
Weight Rest (1) in the same manner.
Slide a 76mm Plastic Bushing (14) onto each
Weight Rest (1). The Plastic Bushings must
be turned as shown.
14
5. Insert a 32mm Square Endcap (40) into each
end of the Adjustment Bar (9). Set the Adjust-
ment Bar in the lowest set of adjustment brackets
on the Right and Left Uprights (2, 26).
5
40
9
38
1
Refer to step 2 and tighten the six M10 Nylon
Locknuts (35) used in that step. Do not over-
tighten the Nylon Locknuts. Next, refer to step
3 and tighten the four M10 x 95mm Bolts (49)
used in that step. Do not overtighten the
Bolts; the Uprights will be damaged and you
will not be able to fully insert the Weight
Rests (1) into the Uprights.
1
40
14
26
17
Adjustment
Brackets
Insert the Weight Rest (1) with the Right Barbell
Lock Pin (38) into the Right Upright (2). Press
the 76mm Plastic Bushing (14) firmly into the
top of the Right Upright. Insert an Adjustment
Pin (17) through the holes in the Right Upright
and the Weight Rest (1).
2
Attach the other Weight Rest (1) to the Left
Upright (26) in the same way. Make sure that
both Weight Rests are at the same height.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Refer to the inset drawing. Insert the Weight
Tube (42) into the indicated hole in the Leg Lever
(21). Attach the Weight Tube with an M8 x 60mm
Bolt (48), two 8mm Washers (46), the 13.5mm
Spacer (47), and an M8 Nylon Locknut (45).
Press two 50mm Square Endcaps (24) into the
Leg Lever.
6
24
23
45
21
46
46
47
48
22
Refer to the inset drawing. Press a 25.4mm
Endcap (22) into the indicated end of the Weight
Tube. Press the Leg Lever Bumper (23) into the
other end of the Weight Tube.
42
24
4
36
Note: The above parts may have been
pre-assembled at the factory.
21
Lubricate the M12 x 95mm Bolt (32). Attach the
Leg Lever (21) to the Frame (4) with the Bolt and
the M12 Nylon Locknut (36). Do not overtighten
the Nylon Locknut.
Lubricate
32
7. Insert 25.4mm Square Endcaps (18) into the
ends of both Backrest Rails (10).
7
8
Attach the Backrest Rails (10) to the Backrest
(8) with four M6 x 40mm Bolts (27) and four M6
Washers (44). Do not tighten the Bolts yet.
Make sure that the Backrest Rails are turned
as shown.
18
10
Attach the Backrest Rails (10) to the tube on the
Frame (4) with the M10 x 190mm Bolt (30), two
10mm Washers (34), and an M10 Nylon Locknut
(35). Do not overtighten the Nylon Locknut.
34
4
44
27
30
44
18
Tighten the four M6 x 40mm Bolts (27).
27
35
34
8. Attach the Seat (7) to the Frame (4) with two M6
x 15mm Screws (29), an M6 x 65mm Bolt (41),
and three M6 Washers (44) as shown.
8
7
4
44
41
29
6
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Insert the Leg Lever Lock Pin (37) into the indi-
cated hole in the Frame (4). Tighten an M10
Nylon Locknut (35) onto the Leg Lever Lock Pin.
Do not overtighten the Nylon Locknut.
9
6
Attach the Preacher Curl Pad (6) to the Curl
Post (5) with four 6mm Washers (44) and four
M6 x 15mm Screws (29).
5
Insert the Curl Post (5) into the Frame (4). Align
one set of holes in the Curl Post with the holes
in the Frame. Insert an Adjustment Pin (17)
through the Curl Post and the Frame.
44
44
29
35
17
4
37
10. Press a 19mm Endcap (33) into each end of the
381mm Pad Tube (13). Insert the Pad Tube into
the welded tube on the Frame (4). Slide a Foam
Pad (11) onto each end of the Pad Tube.
10
Press 19mm Endcaps (33) into the ends of the
356mm Pad Tube (12) and the 381mm Pad
Tubes (13). Insert the Pad Tubes into the Leg
Lever (21). Next, push Foam Pads (11) onto the
ends of the Pad Tubes. Make sure the upper
Foam Pads are under the preacher curl weight
rest.
11
4
33
11
11
13
33
Preacher
Curl Weight
Rest
21
12
33
13
11
11. Make sure that all parts of the weight bench are properly tightened. Any remaining parts will be
explained in HOW TO ADJUST THE WEIGHT BENCH, beginning on the next page.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE WEIGHT BENCH
The instructions below describe how each part of the weight bench can be adjusted. Refer to the exercise infor-
mation accompanying your weight set (not included) to see the correct form for each exercise.
ADJUSTING THE BACKREST
The Backrest (8) has three different positions: a level
position, a decline position, and an incline position.
9
To change the position of the Backrest (8), move the
Adjustment Bar (9) to a different set of adjustment
brackets on the Right and Left Uprights (2, 26). Make
sure that the Adjustment Bar is securely seated in
the adjustment brackets.
26
8
2
ADJUSTING THE WEIGHT RESTS
See the inset drawing. To change weights while your
barbell (not included) is on the Weight Rests (1),
secure your barbell with the Barbell Lock Pins (28,
38). This will reduce the possibility of the barbell tip-
ping while you change weights. Place the same
amount of weight on both ends of the barbell.
28
28
1
1
17
26
To change the height of the Weight Rests (1), first
remove your barbell from the Weight Rests. Remove
the Adjustment Pin (17) from the Weight Rest in the
Right Upright (2). Position the Weight Rest at the
desired height. Align the holes in the Weight Rest with
the holes in the Upright. Re-insert the Adjustment Pin.
38
1
Position the Weight Rest (1) in the Left Upright (26) at
the same height.
17
2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE PREACHER CURL PAD
For some exercises, the Preacher Curl Pad (6)
must be attached to the weight bench.
6
5
Insert the Curl Post (5) into the indicated opening in
the Frame (4). Position the Curl Post at the desired
height and align one of the holes in the Curl Post
with the indicated hole in the Frame. Insert an
Adjustment Pin (17) into the holes.
4
Do not change the amount of weight on your
preacher curl bar while the bar is resting on the
preacher curl weight rest.
Preacher Curl
Weight Rest
17
USING THE LEG LEVER
To use the Leg Lever (21), slide the desired amount
of weight (not included) onto the Weight Tube (42).
If you are using olympic weights, slide the Weight
Adapter (20) onto the Weight Tube. Make sure that
the Weight Adapter Bushings (19) are in the Weight
Adapter.
11
13
37
For some exercises, the Leg Lever (21) must be
locked in place. Refer to the inset drawing. To lock
the Leg Lever, slide the indicated Foam Pad (11)
back from the Leg Lever about one inch. Turn the
Leg Lever Lock Pin (37) so that it clips onto the
381mm Pad Tube (13). Slide the Foam Pad back
into place.
21
Weight
20
42
19
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. PFBE30790
R1099A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
1
2
1
1
1
1
1
1
2
6
1
2
3
2
4
3
4
2
1
1
1
1
3
4
1
Weight Rest
Right Upright
Stabilizer
Frame
Curl Post
Preacher Curl Pad
Seat
Backrest
Adjustment Bar
Backrest Rail
Foam Pad
356mm Pad Tube
381mm Pad Tube
76mm Plastic Bushing
60mm Endcap
76mm Slotted Endcap
Adjustment Pin
25.4mm Square Endcap
Weight Adapter Bushing
Weight Adapter
Leg Lever
25.4mm Endcap
Leg Lever Bumper
50mm Square Endcap
M10 x 85mm Carriage Bolt
Left Upright
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#
4
1
6
1
2
1
6
14
10
1
1
1
4
2
1
1
1
11
1
M6 x 40mm Bolt
Left Barbell Lock Pin
M6 x 15mm Screw
M10 x 190mm Bolt
M10 x 70mm Bolt
M12 x 95mm Bolt
19mm Endcap
10mm Washer
9
M10 Nylon Locknut
M12 Nylon Locknut
Leg Lever Lock Pin
Right Barbell Lock Pin
15mm x 70mm Spacer
32mm Square Endcap
M6 x 65mm Bolt
Weight Tube
50mm x 70mm Outer Cap
M6 Washer
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
M8 Nylon Locknut
8mm Washer
2
1
1
4
4
1
1
13.5mm Spacer
M8 x 60mm Bolt
M10 x 95mm Bolt
4mm x 8mm Screw
UserÕs Manual
#
Exercise Poster
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. PFBE30790
R1099A
28
11
13
35
33
1
12
40
33
50
33
9
11
14
15
50
13
6
33
40
17
26
8
49
34
39
16
35
44
29
3
35
34
1
7
44
38
29
50
18
34
31
5
10
35
14
50
15
10
18
44
27
30
17
18
44
27
25
34
22
19
20
19
24
44
27
18
35
34
36
14
34
2
35
24
34
44
41
49
21
45
29
35
34
39
23
3
31
46
32
4
47
17
43
16
46
42
48
24
37
25
16
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M8 Nylon Locknut (45)Ð1
M6 x 15mm Screw (29)Ð6
M10 Nylon Locknut (35)Ð10
M6 x 40mm Bolt (27)Ð4
M6 x 65mm Bolt (41)Ð1
M8 x 60mm Bolt (48)Ð1
M12 Nylon Locknut (36)Ð1
M6 Washer (44)Ð11
M8 Washer (46)Ð2
M10 x 95mm Bolt (49)Ð4
M10 x 70mm Bolt (31)Ð2
10mm Washer (34)Ð14
Download from Www.Somanuals.com. All Manuals Search And Download.
13.5mm Spacer (47)Ð1
15mm x 70mm Spacer (39)Ð4
M10 x 85mm Carriage Bolt (25)Ð4
M12 x 95mm Bolt (32)Ð1
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
¥ The MODEL NUMBER of the product (PFBE30790)
¥ The NAME of the product (PROFORM¨ 738 weight bench)
¥ The SERIAL NUMBER of the product (see the front cover of this manual)
¥ The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 10 of this manual).
PROFORM¨ is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service cen-
ters with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to
a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center, products used for commercial or rental pur-
poses, or products used as store display models. No other warranty beyond that specifically set forth
above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 159000 R1099A
Printed in China © 1999 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|