Model No. PFBE14530
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Patent Pending
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
maximum total weight of 510 pounds. Do not
place more than 210 pounds, including a bar-
bell and weights, on the weight rests. Do not
place more than 130 pounds on the leg lever.
Note: The weight bench does not include a
barbell or weights.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
11. Always make sure that there is an equal
amount of weight on each side of your bar-
bell when you are using it. Always keep
some weight on both ends of the barbell
when adding or removing weights to prevent
the barbell from tipping.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
12. When you put weight on the weight rests,
make sure that you put at least ten pounds
on the leg lever to balance the weight bench.
5. Make sure that all parts are properly tight-
ened each time the weight bench is used.
Replace any worn parts immediately.
13. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
6. Always wear athletic shoes for foot protec-
tion while exercising.
14. Always remove the curl post from the front
leg before performing leg curls with the leg
lever.
7. Keep children under 12 and pets away from
the weight bench at all times.
8. Keep hands and feet away from moving parts. 15. Always exercise with a partner. When you
are performing bench press exercises, your
9. Make sure that the weight rest pins are in
locked position around the uprights before
beginning any exercise.
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
10. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile PROFORM® C705 toll-free at 1-800-999-3756, Monday through Friday,
weight bench. The weight bench offers a selection of
weight stations designed to develop every major mus-
cle group of the body. Whether your goal is to tone
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the weight bench
will help you to achieve the specific results you want.
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is PFBE14530. The serial number can be
found on a decal attached to the weight bench (see the
front cover of this manual).
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
ASSEMBLED
DIMENSIONS:
Height: 42 in.
Width: 58 in.
Depth: 78 in.
Weight Rest
Right Side
Adjustment Pin
Upright
Left Side
Backrest
Curl Pad
Seat
Leg Lever
Backrest Bracket
Weight Tube
Note: The terms “right side” and “left side” are determined relative to a person sitting on the
bench; they do not correspond to right and left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by anyone. However, it is important to
realize that the versatile weight bench has many
parts and that the assembly process will take
time. Most people find that by setting aside plen-
ty of time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two persons.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1.
1
Before beginning assembly, make sure that
you understand the information in the box
above. For help identifying small parts, use
the PART IDENTIFICATION CHART.
6
Attach a Support (6) and a Large Base Foot (15)
to a Stabilizer (3) with two M10 x 93mm Button
Bolts (37), an M10 Washer (41), an M10 Nylon
Locknut (43), and an M10 Nylon Jamnut (46). Do
not tighten the Locknut and Jamnut yet.
37
37
15
Secure the Large Base Foot (15) to the Stabilizer
(3) with an M4 x 16mm Screw (39).
3
46
Repeat this step with the other Stabilizer (3)
and Support (6).
39
41
43
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Locate the Left Upright (5), which has a name
decal in the indicated location. Press a 2” x 3”
Inner Cap (30) into the Upright.
2
30
Attach the Left Upright (5) and a Large Base Foot
(15) to a Stabilizer (3) with two M10 x 93mm Button
Bolts (37), an M10 Washer (41), an M10 Nylon
Locknut (43), and an M10 Nylon Jamnut (46). Do
not tighten the Locknut and Jamnut yet.
5
Secure the Large Base Foot (15) to the Stabilizer
(3) with an M4 x 16mm Screw (39).
43
41
41
Attach the Left Upright (5) to the Support (6) with
two M10 x 93mm Button Bolts (37), two M10
Washers (41), and two M10 Nylon Locknuts (43).
Do not tighten the Locknuts yet.
6
37
43
37
Repeat this step with the Right Upright (not
shown).
Name decal
on this side
Tighten the M10 Nylon Locknuts (43) and the
M10 Nylon Jamnuts (46) used in steps 1 and 2.
37
3
15
46
41
43
39
3. Attach the Crossbar (4) to the Left Upright (5)
with two M10 x 68mm Button Bolts (38), a
Support Plate (47), and two M10 Nylon Locknuts
(43). Do not tighten the Locknuts yet.
3
Next, attach the Crossbar (4) to the Left Upright
(5) with an M10 x 93mm Button Bolt (37), an M10
Washer (41), and an M10 Nylon Locknut (43). Do
not tighten the Locknut yet.
Repeat this step with the Right Upright (not
shown).
4
38
41
5
43
38
37
43
47
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach a Small Base Foot (14) to the Bench Leg
(2) with an M4 x 16mm Screw (39). Press a
50mm Square Inner Cap (25) and a 50mm
Notched Square Inner Cap (50) into the Bench
Leg.
4
25
43
1
41
Attach the Bench Leg (2) to the Bench Frame (1)
with two M10 x 68mm Button Bolt (38), two M10
Washers (41), and two M10 Nylon Locknuts (43).
Do not tighten the Locknuts yet.
38
43
41
2
14
50
39
5. Attach the Bench Frame (1) to the Crossbar (4)
with two M10 x 68mm Button Bolts (38) and two
M10 Nylon Locknuts (56). Do not tighten the
Locknuts yet.
5
4
38
Tighten the M10 Nylon Locknuts (43) used in
steps 3–6.
43
1
6. Press two 50mm Square Inner Caps (25) into the
Leg Lever (7). Press a 25mm Round Inner Cap
(45) into the Weight Tube (13).
6
43
7
Attach the Weight Tube (13) to the Leg Lever (7)
with an M8 x 63mm Button Bolt (49), two M8
Washers (26), a 12.5mm Spacer (31), and an M8
Nylon Locknut (44). Press the 25mm Round
Angled Cap (32) onto the Weight Tube.
25
42
32
49
44
26
Lubricate
2
Lubricate an M10 x 73mm Button Bolt (42) with
grease. Attach the Leg Lever (7) to the Bench
Leg (2) with the Bolt and an M10 Nylon Locknut
(43). Do not overtighten the Locknut; the Leg
Lever must be able to pivot easily.
31
26
25
13
45
7. Attach the tether on the Weight Rest Pin (23) to a
Weight Rest (11) with an M4 x 16mm Screw (39).
7
11
Slide a Weight Rest (11) onto the Left Upright (5).
Insert the Weight Rest Pin (23) into the Weight
Rest and an adjustment hole in the Upright from
the side shown. Rotate the Pin down so that it
wraps around the back of the Upright.
23
39
5
Repeat this step with the other Weight Rest
(11) and the Right Upright (not shown). Make
sure that the two Weight Rests are set at the
same height.
Adjustment
Hole
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press four 25mm Square Inner Caps (24) into the
Backrest Tubes (9).
8
24
Orient the Backrest Tubes (9) so that the indicat-
ed holes are closer to the bottom. Attach the
Backrest Bracket (8) to the Backrest Tubes with
four M10 x 45mm Button Bolts (35), four M10
Washers (41), and four M10 Nylon Locknuts (43).
Do not tighten the Locknuts yet.
9
35
41
Holes
41
35
24
43
43
8
9. Pull out the Pop Pin (22) as far as it will go. Insert
the Backrest Bracket (8) through the slot in the
Bench Frame (1). Engage the Pop Pin into a hole
in the Backrest Bracket.
9
9
41
43
Lubricate an M10 x 155mm Button Bolt (36) with
grease. Attach the Backrest Tubes (9) to the
Bench Frame (1) with the Bolt, two M10 Washers
(41), and an M10 Nylon Locknut (43). Do not
overtighten the Locknut; the Backrest Tubes
must be able to pivot easily.
22
Slot
41
8
36
1
Lubricate
10. Attach the Backrest (17) to the Backrest Tubes
(9) with four M6 x 38mm Screws (48) and four M6
Washers (34).
10
Tighten the four M10 Nylon Locknuts (43)
used in step 8.
17
9
34
48
34
48
8
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Attach the Seat (16) to the Bench Frame (1) with
an M6 x 63mm Screw (33), an M6 Washer (34),
and two M6 x 16mm Screws (40).
11
16
1
34
33
40
12. Slide a Pad Tube (12) into a hole in the Leg
Lever (7). Wet both sides of the Pad Tube with
soapy water. Slide two Large Pads (19) onto the
Pad Tube as shown. Press two Large Pad Caps
(29) into the Pad Tube. Repeat with another
Pad Tube and the Leg Lever.
12
29
28
19
20
2
Slide the last Pad Tube (12) into the hole in the
Bench Leg (2). Wet both sides of the Pad Tube
with soapy water. Slide two Small Pads (20) onto
the Tube as shown. Press two Small Pad Caps
(28) into the Pad Tube.
12
12
7
20
12
19
28
29
13. Attach the Curl Pad (18) to the Curl Post (10) with
two M6 x 16mm Screws (40).
13
18
10
40
14. Make sure that that all parts are properly tightened before you use the weight bench. The use of all
remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information
and refer to the accompanying exercise guide to see the correct form for each exercise. Refer also to the
exercise information accompanying your weight set for additional exercises.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
To adjust the position of the Backrest (17), hold the
upper end of the Backrest with one hand and pull the
Pop Pin (22 [not shown]) out. Raise or lower the
Backrest to the desired position. Engage the Pop Pin
into an adjustment hole in the Backrest Bracket (8).
17
22
8
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (7), slide the desired weights
(not included) onto the Weight Tube (13).
WARNING:
Do not place more
than 150 pounds on the Weight Tube (13).
7
13
Weight
ADJUSTING THE WEIGHT RESTS
To change the height of a Weight Rest (11), remove
the Weight Rest Pin (23). Position the Weight Rest at
the desired height on the Upright (5 or 51 [not shown])
and secure it with the Pin.
11
23
WARNING:
Always set both
5
Weight Rests (11) at the same height. Make
sure that the Weight Rest Pins (23) are wrapped
around the back of the Uprights (5, 51).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE CURL POST
For some exercises, the Curl Post (10) must be
attached to the weight bench. Remove the 50mm
Square Inner Cap (25). Slide the Curl Post into the
bench Leg (2). Align the adjustment holes in the Curl
Post with the adjustment hole in the Bench Leg.
Tighten the Curl Knob (27) into the Bench Leg. Fully
tighten the Knob.
10
25
2
27
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
MUSCLE BUILDING
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
TONING
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your
resistance.
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
WEIGHT LOSS
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
CROSS TRAINING
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or
exercise bike, on Tuesday and Thursday.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed
for at least one full day each week to give your body
time to regenerate.
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
The combination of strength training and aerobic exer-
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.
op your heart and lungs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on pages 14 and 15 of this manual can be pho-
tocopied and used to schedule and record your work-
outs. List the date, the exercises performed, the resist-
ance used, and the numbers of sets and repetitions
completed. Record your weight and key body meas-
urements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
Q
B
E. Brachioradials (forearm)
R
S
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
C
D
E
T
F
M
N
U
G
H
I
V
W
X
J
K
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
25mm Round Inner Cap (45)
25mm Square Inner Cap (24)
25mm Round Angle Cap (32)
50mm Square
Inner Cap (25)
M6 x 38mm Screw (48)
M10 Washer (41)
M8 Washer (26)
M6 Washer (34)
M10 x 45mm Button Bolt (35)
M6 x 63mm Screw (33)
M8 Nylon Locknut (44)
M8 x 63mm Button Bolt (49)
M10 x 68mm Button Bolt (38)
M10 Nylon Jamnut (46)
M10 Nylon Locknut (43)
M10 x 73mm Button Bolt (42)
M10 x 93mm Button Bolt (37)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFBE14530
R0803A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
2
1
1
2
1
1
2
1
2
3
1
1
4
1
1
1
4
2
4
1
2
4
3
2
1
2
Bench Frame
Bench Leg
Stabilizer
Crossbar
Left Upright
Support
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
#
4
2
1
1
1
5
4
1
14
8
7
4
18
1
24
1
1
4
2
4
Large Pad Cap
2” x 3” Inner Cap
12.5mm Spacer
25mm Round Angled Cap
M6 x 63mm Screw
M6 Washer
M10 x 45mm Button Bolt
M10 x 155mm Button Bolt
M10 x 93mm Button Bolt
M10 x 68mm Button Bolt
M4 x 16mm Screw
M6 x 16mm Screw
M10 Washer
M10 x 73mm Button Bolt
M10 Nylon Locknut
M8 Nylon Locknut
25mm Round Inner Cap
M10 Nylon Jamnut
Support Plate
M6 x 38mm Screw
M8 x 63mm Button Bolt
50mm Notched Inner Cap
Right Upright
Leg Lever
Backrest Bracket
Backrest Tube
Curl Post
Weight Rest
Pad Tube
Weight Tube
Small Base Foot
Large Base Foot
Seat
Backrest
Curl Pad
Large Pad
Small Pad
Weight Rest Bushing
Pop Pin
Weight Rest Pin
25mm Square Inner Cap
50mm Square Inner Cap
M8 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
1
1
1
1
2
1
User’s Manual
Exercise Guide
Allen Wrench
Grease Pack
#
#
#
Curl Knob
Small Pad Cap
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFBE14530
R0803A
23
21
43
11
30
6
21
11
39
18
43
37
21
23
21
15
10
37
51
15
40
30
39
46
17
41
39
41
3
41
43
37
24
43
46
47
39
38
5
9
43
35
43
41
43
37
43
6
34
41
41
9
4
37
38
37
37
43
41
41
37
35
43
48
24 41
34
37
38
43
41
16
36
37
22
38
38
48
37
15
43
43
47
38
43
43
25
8
27
43
1
46
34
39
41
7
3
43
29
33
19
43
15
39
41
43
41
46
32
38
26
40
29
20
25
44
28
26
42
12
41
50
45
31
19
49
13
2
25
14
20
12
29
28
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
1. The MODEL NUMBER of the product (PFBE14530)
2. The NAME of the product (PROFORM® C705 weight bench)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage
or repairs not provided by an ICON authorized service center; products used for commercial or rental pur-
poses; or products used as store display models. No other warranty beyond that specifically set forth above
is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 200004 R0803A
Printed in China © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|