Princeton Stroller SP 300i 500i User Manual

15 Discovery Way, Acton, MA 01720  
Phone: (978)263-3584, Fax: (978)263-5086  
Operating Instructions  
for  
Triple Grating Turrets  
SP-300i/500i  
Ver 2.0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Become familiar with the components as labeled on Figures 1, 2 and 3 in this  
section.  
2. Scan the instrument to grating #1 and the highest wavelength position.  
3. Place the monochromator in a clean, dust free area.  
4. Remove the screws from the monochromator access cover and remove the  
access cover. Become familiar with the grating turret and its components.  
5. Locate a 9/64 ball end hex driver (Bondhus #9/64)*. Refer to Figure #3 and  
with the 9/64 ball end hex driver, loosen the turret clamping screw #1.  
(NOTE: All 3 turret clamping screws are captive). Loosen the turret clamp  
screw #2 and then #3.  
6. Use extreme care so as not to touch the grating surfaces and grasp the top  
plates of the grating turret, refer to Figure 2. Lift the grating turret straight up  
off the grating spindle assembly. If the turret cannot be lifted up, assure the 3  
clamping screws are disengaged from the grating spindle assembly.  
7. Place the removed grating turret assembly on a clean surface.  
8. Remove the plastic cover from the grating turret storage container. Loosen  
the 3 grating turret clamping screws. NOTE: These screws are captive.  
CAUTION: Do not hit the grating surfaces as permanent damage will be  
caused.  
9. Carefully grasp the grating turret by the top plates. CAUTION: Do not touch  
the grating surfaces. Lift the grating turret out of the storage container.  
10.Locate the grating turret # on the grating turret assembly. Assure the  
monochromator is as grating #1 and highest wavelength position. Refer to  
Figure #1 and place the grating turret on the grating spindle with the turret #  
located as shown.  
11.Assure the turret is properly seated, the ball in the cone hole and the rod in  
the vee groove.  
12.Lightly tighten clamp screw #1, then #2 and #3. (NOTE: To assure maximum  
reproducibility, the clamping screws must be tightened in this sequence and  
to 3 inch pounds of torque.) Tighten screw #1, to 3 inch pounds of torque,  
then #2 and #3. The grating turret is now installed.  
13.Place the access cover on the monochromator. Replace and tighten the 8  
cover screws.  
14.Install the removed grating turret into the storage container and tighten the 3  
clamp screws. Replace the plastic cover.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTERCHANGING TURRETS  
FIGURE 1  
FIGURE 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Perle Systems Server 4030370 User Manual
Philips Headphones SBCHJ030 User Manual
Philips Stereo Amplifier CR6927 User Manual
Pioneer TV Video Accessories AVH 170DVD User Manual
Porter Cable Grinder PCB575BG User Manual
Poulan Chainsaw 952802143 User Manual
Poulan Lawn Mower 178087 User Manual
Poulan Lawn Mower Accessory 960 72 00 13 User Manual
ProForm Home Gym GT 30 User Manual
PYLE Audio Car Video System PLVW1350IR User Manual