QUANTUM
S E R I E S
INNOVATIVE REHAB SOLUTIONS
Including Models: Quantum 1122 3SP, Quantum 1122 4MP
1-800-800-8586 (US) 1-888-570-1113 (Canada)
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
I.
INTRODUCTION..................................................................................................................................... 4
II. SAFETY ..................................................................................................................................................... 6
III. YOUR POWER CHAIR........................................................................................................................ 16
IV. ASSEMBLY............................................................................................................................................. 21
V. COMFORT ADJUSTMENTS............................................................................................................ 23
VI. DISASSEMBLY ..................................................................................................................................... 31
VII. BATTERIES AND CHARGING ........................................................................................................ 32
VIII.CARE AND MAINTENANCE ............................................................................................................ 37
IX. WARRANTY............................................................................................................................................ 42
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
3
I . I N T R O D U C T I O N
SAFETY
WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you have
purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these
design features will provide you with the conveniences you expect during your daily activities. Once you understand how
to safely operate and care for your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup
or operation, please contact your Quantum Rehab Specialist. Failure to follow the instructions in this manual and
those located on your power chair can lead to personal injury and/or damage to the power chair, including
voiding the warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually packaged.
If you do not receive a complete delivery, please contact your Quantum Rehab Specialist immediately. Where damage has
occurred during transport, either to the packaging or content, please contact the delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety
and reliability of your new power chair, and about the service you received from your Quantum Rehab Specialist.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us
at the address below:
USA:
Canada:
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 SusquehannaAvenue
Exeter, PA18643-2694
800-424-8205
Pride Mobility Products Company
380 Vansickle Road Unit 350
St. Catharines, Ontario L2R 6P7
1-888-570-1113
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I . I N T R O D U C T I O N
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive
message boards. These message boards invite you to communicate with other Pride customers as well as Pride represen-
tatives who are available to assist you with any questions or concerns you may have.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
5
I I . S A F E T Y
PRODUCT SAFETY SYMBOLS
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very
important for you to read and understand them completely.
Corrosive chemicals contained in battery. Use only AGM or Gel-Cell batteries to reduce
the risk of leakage or explosive conditions.
This product has been tested and passed at an immunity level of 20 V/m.
Read and follow the information in the owner’s manual.
Maximum seating weight.
Unlocked and in freewheel mode.
Place unit on level ground and stand behind or to one side when changing from drive mode
to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Battery Set Configuration:
+ = Positive (Red) Terminal Post
– = Negative (Black) Terminal Post
Connect Red wires to Red Positive (+) Terminal Posts
Connect Black wires to Black Negative (–) Terminal Posts
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I . S A F E T Y
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and
store in a clean and dry condition.
Removal of grounding prong can create electrical hazard. If necessary, properly install an
approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
Do not connect an extension cord to the AC/DC converter or the battery charger.
Do not remove anti-tip wheels.
Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper
disposal and recycling of your Pride product and its packaging.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
7
I I . S A F E T Y
GENERAL GUIDELINES
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair
to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Specialist in the instruction
process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice operating
the power chair in the presence of a trained attendant.Atrained attendant can be defined as a family member or care
professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,
on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating your
power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility.Awide range of accessories
is available from your Quantum Rehab Specialist to further customize your power chair to better suit your needs and/or
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function
of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain but do not exceed 35 psi (2.4 bar) in each tire if equipped with
pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the power base. Make sure they are secured properly.
! Check the brakes. See VIII. “Care and Maintenance.”
! Check battery charge. See VII. “Batteries and Charging.”
NOTE: If you discover a problem, contact your Quantum Rehab Specialist for assistance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I . S A F E T Y
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
WARNING! Stay within the specified weight capacity of your power chair. Exceeding the weight
capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage
resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the center of gravity, resulting in a tip or a fall.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly. Proper
inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at all
times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and
overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic tires at
all times may result in tire and/or wheel failure.
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a
burst tire.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent.
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive in the forward
direction only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come
to a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline.
Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.
Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the power chair in freewheel
mode while seated on it or standing next to it.
WARNING! Never travel down an incline backward. Doing so may cause the power chair to tip.
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiate
inclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seat
in a reclined position unless an attendant is present to help stabilize the chair. Failure to heed
may result in the power chair tipping over.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
9
I I . S A F E T Y
WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated
in figure 1, do not, under any circumstances, exceed the incline guidelines or any other
specifications presented in this manual. Doing so could cause instability in your power chair.
In compliance with theAmericans with DisabilitiesAct of 1990, all handicap public access ramps are required to have a
maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely
ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip.
5 (8.7%)
Figure 1. Maximum Safe Angle (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained attendant.
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline. The chair could
roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
! Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
! Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when power is
removed from the system for any reason.
Cornering Information
While your power chair is equipped with rear caster wheels and front anti-tip wheels, excessively high cornering speeds
can still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to:
cornering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an
area of low traction to an area of high traction (such as passing from a grassy area to a paved area – especially at high
speed while turning), and abrupt directional changes. High cornering speeds are not recommended. If you feel that you
may tip over in a corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power
chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.
This greatly reduces the possibility of a tip or fall.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I . S A F E T Y
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to
use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest opportunity.
Thoroughly dry your power chair before storing, charging, or operating your power chair.
WARNING! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces can
have an adverse effect on the electrical system. Maintain and store your power chair in a dry and
clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered
and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution
when using your power chair in extremely hot or cold conditions or when exposing your power
chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,
stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate. See figure 2.
CURB
Figure 2. Correct Curb Approach
Figure 3. Incorrect Curb Approach
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
11
I I . S A F E T Y
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 2 in. (5 cm) unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or
other obstacle. This may cause the power chair to tip.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators.Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly
backward to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transporta-
tion. Pride recommends that you closely review the instructions, specifications, and safety information set forth by the
manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any type of lift/
elevation product. Your power chair was not designed with such use in mind and any damage or
injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle.
WARNING! Always be sure your power chair and its batteries are properly secured when it is being
transported. Batteries should be secured in an upright position and protective caps should be
installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.
Positioning Belts
Your Quantum Rehab Specialist, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I . S A F E T Y
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For more
information about your power chair’s batteries, seeVII. “Batteries and Charging.”
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging
a frozen battery may result in damage to the battery.
WARNING! Connect your battery harnesses in the proper manner. RED (+) cables must be connected
to positive (+) battery terminals/posts. BLACK (-) cables must be connected to negative (-) battery
terminals/posts. Protective caps should be installed over all battery terminals. REPLACE cables
immediately if damaged.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including the
armrests, seat, foot riggings, controller, and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the
presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by
reaching down between your knees or if you have to reach over the back of the seat. Movements
such as these may change your center of gravity and the weight distribution of the power chair,
possibly causing your power chair to tip.
WARNING! Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
13
I I . S A F E T Y
Transfers
Transferring onto and off of your power chair requires a
good sense of balance.Always have an attendant or health-
care professional present while learning to properly trans-
fer yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks be-
fore attempting a transfer:
! Turn off the power to the controller.
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn the caster wheels toward the transfer destination
to improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed
from your power chair.
! Flip up the foot platform or move the leg rests aside;
this will help to keep your feet from getting caught on
the foot rigging during the transfer.
! Reduce the distance between your power chair and
the object you are transferring onto.
Figure 4. IdealTransfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer.
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the armrests
for weight bearing purposes, such as transfers. Such use may cause the power chair to tip, resulting
in a fall from the power chair.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your ability
to operate your power chair in a safe manner.
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness
of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I . S A F E T Y
WARNING! Although the power chair seat has passed the necessary testing requirements for
cigarette smoke, Pride recommends that you adhere to the following safety guidelines:
!
!
!
Do not leave lit cigarettes unattended.
Keep ashtrays a safe distance from the seat cushions.
Always make sure cigarettes are completely extinguished before disposal.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This
product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.
Exercise caution when using any of these items while operating your mobility vehicle and avoid
coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride
at 800-424-8205 to report the incident.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
15
I I I . Y O U R P O W E R C H A I R
THE QUANTUM 1122 SERIES POWER CHAIR
Your power chair has two main assemblies: the seat and the power base. See figure 5. Typically, the seating assembly
includes the armrests, seatback, and controller. The power base assembly includes two drive wheels, two anti-tip
wheels, two rear caster wheels, a power seat connector (optional), harness connectors, and a body shroud. See figures
5 through 9.
SEATBACK
ARMREST
SEAT ASSEMBLY
JOYSTICK
CONTROLLER
SEAT BASE
BODY SHROUD
POWER BASE ASSEMBLY
FOOT RIGGING
(FOOT PLATFORM SHOWN)
REARCASTERWHEEL
DRIVEWHEEL
ANTI-TIP WHEELS
Figure 5.The Quantum 1122 Series Power Chair
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I I . Y O U R P O W E R C H A I R
SPECIFICATIONS
Suspension:
Active-Trac with Rear Suspension
Drive Wheels:
14 in. (35.56 cm), pneumatic or solid, center-mounted
Caster Wheels:
Anti-tip Wheels:
Maximum Speed:¹
Range:1
8 in. (20.32 cm), solid, rear-articulating
6 in. (15.25 cm), solid, front mounted
Up to 6 mph (9.65 km/h)
Variable up to 25 miles (40 km)
“Intelligent Braking,” electronic regenerative, disc park brake
3.25 in. (8.25 cm)
Brakes:
Ground Clearance:²
Turning Radius:²
Overall Size:²
23 in. (58.42 cm)
Length: 39.5 in. (100.33 cm)
Width: 25.75 in. (65.4 cm)
Drivetrain:
Batteries:³
Two motor, mid-wheel
Two 12-volt, deep-cycle Group 24 batteries
NF-22 batteries used with power elevating seat option
8-amp, off-board (standard)
Battery Charger:
5-amp, onboard/8-amp, off-board combo
300 lbs. (136 kg)
Weight Capacity:
ComponentWeights: Base: 140 lbs. (63.5 kg)
Batteries: 53.5 lbs. (24.26 kg) each
1
Varies with base model, user weight, terrain type, battery amp hour rating (AH), battery charge, battery condition, motors, controller
type, tire type, and tire condition.
²
³
Due to manufacturing tolerances and continued product improvement, this specification can be subject to a variance of (+ or – ) 3%.
AGM or Gel-Cell type recommended.
NOTE: All specifications subject to change without notice.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
17
I I I . Y O U R P O W E R C H A I R
Electronics Tray
The electronics tray is located on the rear of your power chair, underneath the rear sliding door. The electronics tray
consists of the main circuit breaker, accessory connector (optional equipment), and the controller harness connectors. If
your power chair is equipped with an optional onboard battery charger, the electronics tray will also consist of an ammeter
and charger power cord receptacle.
Main Circuit Breaker:The main circuit breaker is a safety feature built into your power chair. When the batteries and the
motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and
the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit
breaker button, turn on the controller, and continue normal operation. If the main circuit breaker continues to trip repeat-
edly, contact your Quantum Rehab Specialist.
Accessory Connector (Optional): This is where the accessory harness connects to the controller (power seat, lighting).
Controller Connector: This is where the controller connects to the power module. Each controller uses a different type
of cable. Regardless of which type of controller is used, the cable must be secured to the seat assembly and not allowed to
drag on the floor.
Ammeter(with optional onboard charging system): The ammeter displays the charger’s current output in amps. For
more information, see VII. “Batteries and Charging.”
Charger Power Cord Receptacle (with optional onboard charging system): This plug is used whenever your battery
needs recharging.
CHARGERPOWERCORDRECEPTACLE
CONTROLLER CONNECTOR
OPTIONAL ACCESSORY CONNECTOR LOCATION
AMMETER
CHARGERFUSE
MAINCIRCUITBREAKER
Figure 6. ElectronicsTray (Shown with Optional Onboard Charging Components)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I I I . Y O U R P O W E R C H A I R
Active-Trac Suspension
Your power chair is equipped with Active-Trac Suspension (ATS).ATS is a suspension system designed to make your
power chair traverse different types of terrain and obstacles while maintaining smooth operation. WithATS, the front anti-
tip wheels work in conjunction with the motor suspension to help you maneuver over obstacles.
As the front anti-tip wheels come in contact with an obstacle, the front anti-tip wheel assembly is drawn upward.At the
same time, the motors are forced downward. This allows the motors to push the power chair over an obstacle and limits
the possibility of your power chair getting caught on the obstacle.
ATS also helps in day-to-day operating conditions. For instance, when you release the joystick your power chair begins to
slow down.As the chair slows down, the front anti-tip wheels will automatically drop toward the ground. This will reduce
the forward tip that is typically encountered with center-wheel drive chairs.
Rear Suspension
Your power chair is equipped with a rear suspension system. See figure 7. This suspension system works in conjunction
with theATS and is designed to maintain a smooth ride when driving over rough terrain and up and down curbs. This
system works by allowing the caster forks to respond to weight transfers and uneven terrain. The rear caster wheels will
pivot as you drive over obstacles. This system also enhances performance when the front anti-tip wheels are set lower to
the surface.
REAR CASTER FORK
REARCASTERWHEEL
REAR CASTER FORK
REARCASTERWHEEL
Figure 7. Rear Suspension System
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
19
I I I . Y O U R P O W E R C H A I R
Dual Manual Freewheel Levers
For your convenience, your power chair is equipped with dual manual freewheel levers. The levers are located on the
inside of the anti-tip wheels. The levers allow you to disengage the drive motors and maneuver the chair manually.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage
the drive motors when the power chair is on an incline, as the unit could roll on its own! Only
engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
To operate the dual manual freewheel levers:
1. Pull up both manual freewheel levers for freewheel mode (drive motor disengaged). See figure 8.
2. Push down both manual freewheel levers for drive mode (drive motor engaged). See figure 9.
If a lever is difficult to move in either direction, rock your power chair back and forth slightly. The lever should then move
to the desired position.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.
Figure 8. Freewheel Mode (left side shown)
Figure 9. Drive Mode (left side shown)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I V . A S S E M B L Y
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your Quantum Rehab Specialist.
Seat Installation
Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal
parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main
components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are
mounted to the power base. See figure 10.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Position-
ing System, refer to the information provided in separate manuals.
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose
control of the seat if they do so.
SEAT LATCH SAFETY
REAR EXTRUSION
FRONT EXTRUSION
REARTRAPEZEBAR
FRONT TRAPEZE BAR
Figure 10. Seat Installation
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
21
I V . A S S E M B L Y
To install the seat:
1. Set the trapeze bars to the desired height. To change
the trapeze bar height, see V. “ComfortAdjustments.”
2. Tilt the seat back and slide the rear extrusion onto the
rear trapeze bar. See figure 10.
3. Lower the front extrusion onto the front trapeze bar
until the seat locks into place.
4. Flip the seat latch safety down.
WARNING! Make sure the seat latch
safety is flipped down before using your
power chair.
5. Install the controller into one of the armrests. See V.
“ComfortAdjustments.”
6. Route the controller cable so that it cannot be pinched
in the seat hinge.
7. Slide the rear cover open to expose the electronics tray.
8. Plug the controller connector into the electronics tray.
See figure 6.
Figure 11. Power Elevating Seat Actuator
9. Secure the controller cable to the armrest receiver with
one or more wire ties.
Power Elevating Seat Installation (Optional)
Your power chair may be equipped with a power elevating
seat option. While the seat itself may be any one of the
styles offered for this model, the way the seat base attaches
to the power base is different.
To install the power elevating seat:
l. Align the seat post on the seat base to the hole in the
actuator. See figure 11.
2. Insert the seat post into the actuator and push the seat
lever forward to lock the seat into place.
3. Plug the power elevating seat switch cable into the con-
nector on the electronics tray.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V . C O M F O R T A D J U S T M E N T S
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and the controller’s position.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or Synergy TRU-Balance, refer to
the information provided in separate manuals. If your power chair is equipped with a contoured seating sys-
tem, refer to the following information.
WARNING! If your power chair was configured at your Quantum Rehab Specialist, please consult
your healthcare professional before changing the seat position or making any other adjustment.
Some adjustments may degrade your power chair’s performance and safety by changing its center
of gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjust-
ments:
! metric/standard hex key set
! metric/standard socket set and ratchet
! adjustable wrench
Seat Height/Angle Adjustment
The seat is attached to the power base through the UMS.
You can change the seat height by raising the front and rear
trapeze bars. If you raise or lower only one set of trapeze
bars (front or rear), you can also change the seat base angle
(dump).
Figure 12. Seat Latch Safety (Disengaged)
QUICK-RELEASEPINS
To change the seat height:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the electronics
tray.
TRAPEZE BARS
3. Flip up the seat latch safety. See figure 12.
4. Squeeze the seat latch and release the seat from the
front trapeze bar.
SEAT TOWER
BALL DETENT PINS
5. Slide the seat forward and remove it from the power
base.
6. Remove the quick-release pins from the seat towers
(front and rear). See figure 13.
7. Remove both trapeze bars from the seat towers.
8. Lift off the shroud
Figure 13. Seat Height Adjustment
9. Remove the ball detent pin from each of the four seat
towers. See figure 13.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
23
V . C O M F O R T A D J U S T M E N T S
10. Move the seat towers up or down to the desired height.
11. Reinstall the ball detent pin into each seat tower.
12. Reinstall the shroud.
13. Reinstall the trapeze bars and secure with the quick-
release pins.
14. Reinstall the seat.
WARNING! Make sure the seat latch
safety is flipped down before using the
power chair.
15. Plug the controller connector(s) into the electronics tray.
Seat Position
You can move the seat forward or rearward by changing
the extrusion mounting position.
To change the seat position:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the electronics
Figure 14. Seat Position Adjustment
tray.
3. Remove the seat from the power base.
4. Remove both extrusions from the bottom of the seat.
5. Reposition the extrusions on a different set of mount-
ing holes. You must move both extrusions the same
number of holes either forward or backwards. See
figure 14.
6. Fasten the extrusions back onto the bottom of the seat.
7. Reinstall the seat.
8. Plug the controller connector(s) into the electronics tray.
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you
can adjust the seatback angle with the seatback release le-
ver. The lever is located on the right side of the seat base.
To adjust the seatback angle:
1. Pull up on the seatback release lever.
2. Move the seatback down or up to the desired position.
3. Release the lever.
Headrest Height Adjustment
If your power chair is equipped with an optional deluxe
high-back seat, you can adjust the headrest height.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V . C O M F O R T A D J U S T M E N T S
To adjust the headrest height:
1. Push in the headrest release button.
2. Move the headrest up or down to the desired position.
JAMNUT
Seatback Angle Adjustment
ARMRESTANGLE
ADJUSTINGSCREW
If your power chair is equipped with an adjustable seatback,
you can adjust it to four (4) different angles: 90°, 102°,
105°, or 107°. See figure 15.
ARMREST HEIGHT
ADJUSTING
To adjust the seatback angle:
SETSCREWS
1. Remove the seatback angle adjustment screws from
both seat hinges.
2. Set the seatback at the desired angle.
3. Reinstall the screws to both seat hinges and tighten.
SEATBACKANGLE
ADJUSTINGSCREW
Armrest WidthAdjustment
Youcanchangeeacharmrest’swidthindependentlyoftheother.
ARMREST KNOB
NOTE: Changing the armrest width may increase the
overall width of your power chair.
Figure 15. Seatback and Armrest Adjustments
To change the armrest width:
1. Locate the two armrest knobs on each side of the arm-
rest receiver bracket. See figure 15.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest HeightAdjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest
receiver.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to
the floor.
2. Loosen the jam nut. See figure 15.
3. Loosen the armrest angle adjusting screw.
4. Turn the adjustment screw to raise the front of the arm-
rest or to lower the front of the armrest. See figure 15.
5. Tighten the jam nut to lock the adjusting screw into
place.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
25
V . C O M F O R T A D J U S T M E N T S
Controller Position
You can move the controller in toward or out away from
the armrest, or change the position of the controller for ei-
ther left-hand or right-hand use.
WARNING! Do not place the controller
cable so that it can be pinched in the seat
frame or the power base frame.
CONTROLLER BRACKET
SETSCREW
To extend the controller:
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See
figure 16.
3. Slide the controller into or out of the armrest to the
desired position.
To change the controller position:
1. Turn off the power to the controller.
2. Unplug the controller connector from the power base.
3. Remove any wire ties securing the controller cable to
the armrest.
Figure 16. Underside of Armrest
4. Flip up the armrest so it is perpendicular to the floor.
5. Loosen the setscrew on the controller bracket.
6. Slide the controller out of the armrest.
7. Loosen the setscrew in the other armrest.
8. Place the controller in the other armrest.
9. Tighten the setscrew to secure the controller.
10. Route the controller cable to the back of the power
base and plug in the controller.
MOUNTING
SCREWS
11. Secure the controller cable to the armrest with wire ties.
NOTE: If your power chair is equipped with a Spe-
cialty Seat, Synergy Seat, or TRU-Balance Power Po-
sitioning System, loosen the mounting screws in the
mounting block, transfer the mounting block and con-
troller to the opposite armrest, and tighten the mount-
ing screws. See figure 17 .
SETSCREWS
Figure 17. Controller Position Mounting Bracket
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V . C O M F O R T A D J U S T M E N T S
Foot Platform Height Adjustment
The foot platform height can be easily adjusted to one of
six different heights.
FOOT PLATFORM BRACKET
NUTS AND BOLTS
To raise or lower the foot platform:
1. Remove the nuts and bolts from the foot platform
bracket. See figure 18.
2. Raise or lower the foot platform to the desired height.
3. Reinstall the nuts and bolts to the foot platform bracket
and tighten.
Foot Platform Depth Adjustment
To adjust the foot platform depth:
BALL DETENT PIN
1. Remove the nuts and bolts from the foot platform
bracket. See figure 18.
Figure 18. Foot Platform Height Adjustment
2. Move the foot platform in or out to the desired depth.
3. Reinstall the nuts and bolts to the foot platform bracket
and tighten.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a hex key.
Seefigure19.
To adjust the foot platform angle:
1. Locate the setscrew on the underside of the foot plat-
form.
2. Turn the setscrew to raise or lower the front of the foot
platform.
SETSCREW
Figure 19. Foot Platform Angle Adjustment
Swing-away Footrests (Optional)
Swing-away footrests (SFRs) are an option. They enable
you to swing the footrest to the side before transferring from
your power chair.
To swing the footrests:
1. Push in the SFR release lever. See figure 20.
2. Swing the footrest off to the side.
SFR RELEASELEVER
FOOTREST
EXTENSION
To adjust the SFR length:
1. Remove the two screws from the side of each leg rest
extension.
ADJUSTMENT
SCREWS
2. Slide the leg rest in or out to the desired length.
3. Reinstall the two screws on each leg rest extension.
Figure 20. Swing-Away Footrests
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
27
V . C O M F O R T A D J U S T M E N T S
Elevating Leg Rests (Optional)
Elevating Leg Rests (ELRs) offer an infinite range of ad-
justment for the leg angle and a footrest adjustment range
of 12–19 in. (30.5–48.25 cm). See figure 21.
RELEASE LEVERA
RELEASE LEVERB
To adjust the ELR angle:
1. Push down release lever B.
2. Move the leg rest to the desired angle.
LEG REST
EXTENSION
To rotate the ELR:
1. Push in release leverA.
2. Rotate the ELRs.
ADJUSTMENT
SCREWS
To adjust the ELR length:
1. Remove the two screws from the side of each leg rest
extension.
2. Slide the leg rest in or out to the desired length.
3. Reinstall the two screws on each leg rest extension.
Figure 21. Elevating Leg Rests
Anti-Tip Wheel Adjustment
The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are
preset for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be
necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if either of the
followingoccur:
! When coming to a stop, your power chair tips forward excessively.
! The anti-tip wheels constantly rub the ground.
WARNING! Consult your Quantum Rehab Specialist before attempting to change the anti-tip height!
Changing the anti-tip wheel height affects handling under deceleration!
WARNING! The higher you raise the anti-tip wheels, the more tendency your power chair has to
tilt forward when coming to a stop. You can compensate for this by making a small adjustment to
the pre-programmed deceleration setting in the controller or by moving the seat assembly farther
to the rear of your power chair.
PROHIBITED! Do not remove the anti-tip wheels from your power chair.
NOTE: Each drive tire must have at least 35 psi (2.4 bar) of air pressure in order for the anti-tip wheels to be
properly adjusted.
To adjust the anti-tip wheels:
1. Place a wrench on the inner locknut of the anti-tip bracket located right after the shock strut. See figure 22.
2. Turn the locknut counterclockwise to loosen.
3. Place your wrench on the adjustable cam located on the other side of the locknut. See figure 23.
4. To adjust the anti-tip upward, turn the cam counterclockwise. To adjust the anti-tip downward, turn the cam clockwise.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V . C O M F O R T A D J U S T M E N T S
Figure 22. Anti-TipWheel Adjustment (Inner Lock Nut)
Figure 23. Anti-TipWheel Adjustment (Cam)
Power Elevating Seat Adjustment (Optional)
Your power chair may be equipped with a power elevating seat actuator. See figure 11. The power elevating seat is
equipped with a speed inhibit system that reduces power chair speed by one-half whenever the seat is elevated more than
1–2 in. (2.54–5 cm).Always check to be sure the speed inhibit system is operating properly before using your power chair,
and do not move around in your seat to any great extent when the seat is in the raised position.
The power elevating seat can enhance the capabilities of the power chair in several ways:
! By elevating the seat, your level of reach is extended to allow more freedom and independence in many environments.
! You can easily adjust the seat height to any surface to which you want to transfer. The seat swivels 90 degrees to
whichever side the joystick is located.
! By raising your seat, you are closer to the eye level of standing persons. This provides better interaction.
For all the benefits the power elevating seat can provide you, there are limitations.
WARNING! Always fasten the positioning belt when operating the power elevating seat.
WARNING! The power elevating seat is intended for use on a level surface only. Never raise the
power elevating seat from its lowest position on an inclined surface. Failure to heed this warning
can result in the power chair tipping over.
WARNING! Never raise the power elevating seat from its lowest position when operating your
power chair on bumpy or uneven surfaces. Failure to heed this warning can result in the power
chair tipping over.
WARNING! Never raise the power elevating seat while your power chair is in freewheel mode.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
29
V . C O M F O R T A D J U S T M E N T S
Power Elevating Seat Operation
You can control the power elevating seat through either the
toggle switch located on the armrest (see figure 24) or
through the controller. For information on how to raise and
lower the power elevating seat through your controller, con-
tact your Quantum Rehab Specialist.
To operate the power elevating seat through toggle
switch:
1. Push the toggle switch forward to raise the seat. When
you release the toggle switch, the seat will stop. Once
the seat reaches its highest extension, the lift action will
stop, but you should continue to hear and/or feel the lift
motor running. This is because there is a clutch mecha-
nism that allows the motor to continue running after the
lift has reached its limit. This clutch works at both the
top and bottom extensions of the lift.
Figure 24. Power Elevating Seat Switch
NOTE: Do not allow the motor to run more than a
few seconds after the mechanism reaches the top or
bottom limit.
2. Pull the toggle switch backward to return the seat to
its lowest position. When returning to the lowest po-
sition, always be sure that the mechanism has reached
its lowest limit.
To use the swivel feature:
1. Locate the friction lock lever under the seat.
2. Pull back on the friction lock lever and rotate the seat
90° to whichever side the controller is located.
3. Push the friction lock lever forward to lock the seat
in place.
WARNING! Do not attempt to drive the
power chair with the seat facing to the
side. Always return the seat to the
forward facing position before operating
the power chair.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I . D I S A S S E M B L Y
Seat Removal
You may wish to remove the seat for transportation.
NOTE: If your power chair is equipped with a Spe-
cialty Seat, Synergy Seat, or TRU-Balance Power
Positioning System, refer to the information provided
in separate manuals.
To remove the seat:
1. Turn off the power to the controller.
2. Make sure your power chair is not in freewheel mode.
See III. “Your Power Chair.”
3. Unplug the controller connector from the electronics
tray.
Figure 25. Seat Safety Latch
4. Flip up the seat latch safety. See figure 25.
5. Squeeze the seat latch and release the seat from the
front trapeze bar.
6. Slide the seat forward and remove it from the power
base.
To remove a power elevating seat:
1. Turn off the power to the controller.
2. Unplug the power elevating seat cable from the elec-
tronics tray.
3. Unplug the controller from the electronics tray.
4. Release the seat by moving the seat release lever back-
ward.
BALL DETENT PIN
5. Lift the seat off of the actuator.
Figure 26. Foot Frame Removal
Foot Frame Removal
The foot frame helps protect the power chair components
from the environment. See figure 26.You must remove the
foot frame in order to change the batteries and check the
cable connections.
To remove the foot frame:
1. Turn off the power to the controller
2. Make sure your power chair is not in freewheel mode.
See III. “Your Power Chair.”
3. Locate and remove the ball detent pin at the base of
the footrest bracket. See figure 18.
4. Lift the foot frame straight up approximately 2 in. (5 cm)
and pull toward you.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
31
V I I . B A T T E R I E S A N D C H A R G I N G
Batteries and Charging
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries.These batteries are sealed and maintenance free. Since
they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and
deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.Automotive
batteries are not designed to handle a long, deep discharge, and also are unsafe for use in powered wheelchairs.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Do not use batteries that exceed the recommended type and amp-hour capacity. Do
not use batteries with different amp-hour capacities. Refer to specifications table in this manual
and in the manual suppled with the battery charger for recommended type and capacities.
Charging The Batteries
The battery charger is essential in providing long life for your power chair batteries. The battery charger is designed to
optimize your power chair’s performance by charging the batteries safely, quickly, and easily. If your power chair is
equipped with an optional onboard battery charger, the charging system consists of the battery charger, the charger fuse,
and the ammeter. The onboard charger is located underneath the electronics tray. The ammeter and charger fuse are
located on the electronics tray for easy viewing. See figure 6. The ammeter indicates the rate of charge being adminis-
tered to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter
and the charger are only functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger directly
into a properly wired standard electrical outlet.
WARNING! You must recharge your power chair’s batteries with the supplied off-board or optional
onboard battery charger. Do not use an automotive-type battery charger.
WARNING! Read the battery charging instructions in this manual and in the manual supplied with
the battery charger before charging the batteries.
WARNING! Do not expose the battery charger to rain or other sources of moisture unless it has
been tested for outdoor use. Refer to the manual supplied with the battery charger for more
information.
WARNING! Explosive gases may be generated while charging the batteries. Keep the power chair
and battery charger away from sources of ignition such as flames or sparks and provide adequate
ventilation when charging the batteries.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each use. Contact
your Quantum Rehab Specialist if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does not
appear to be working correctly, contact your Quantum Rehab Specialist.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to insert
objects through these slots.
WARNING! Do not allow unsupervised children to play near the power chair while the batteries
are charging. Pride recommends that you do not charge the batteries while the power chair is
occupied.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I I . B A T T E R I E S A N D C H A R G I N G
WARNING! If the battery charger has not been tested and approved for outdoor use, then do not
expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse
or extreme weather conditions, then it must be allowed to adjust to the difference in environmental
conditions before use indoors. Refer to the manual supplied with the battery charger for more
information.
To charge the batteries using the off-board charger:
1. Position the front of your power chair next to a standard electrical outlet.
2. Turn off the power to the controller and engage the manual freewheel lever(s) in the drive position. See III. “Your
Power Chair.”
3. Plug the 3-pin extension cable from the off-board battery charger into the off-board battery charger/programming
socket on the controller.
4. Plug the off-board battery charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off-
board charger, then follow the instructions supplied by the manufacturer.
.
5. When the batteries are fully charged, disconnect the charger from the electrical outlet, then from the controller.
To charge the batteries using the onboard charger:
1. Position the rear of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your
Power Chair.”
3. Slide the rear cover forward.
4. Extend the charger power cord and plug it into the electrical outlet.
NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is
plugged into an electrical outlet.
5. We recommend you charge the batteries for 8 to 14 hours.As the batteries charge, the ammeter needle slowly drops
to zero.
NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute
for the charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to 0
amps as the batteries charge.
6. When the batteries are fully charged, the needle vibrates on or near the zero mark on the ammeter scale. Unplug the
power cord from the electrical outlet, wind it up using the hook and loop strap, and place the cord back into the
electronics tray.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
33
V I I . B A T T E R I E S A N D C H A R G I N G
Battery Break-In
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak perfor-
mance level.
2. Operate your power chair about the house and yard. Move slowly at first, and do not travel too far until you become
accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries should now
perform at over 90% of their potential.
4. After four or five charging cycles, the batteries top off at 100% charge and last for an extended period.
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120VAC (alternating current) and converts it to 24 VDC
(direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the
charger works harder to charge the battery. As the battery voltage approaches full charge, the charger doesn’t work as
hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at zero.
This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do
not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your Quantum Rehab Specialist for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries.You may use your power chair all day on a
daily basis or you may not use it for weeks at a time.
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished. Your power chair will be
ready each morning to give you a full day’s service. It is recommended that you charge the batteries 8 to 14 hours after
daily use.
! Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week
for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I I . B A T T E R I E S A N D C H A R G I N G
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often
you are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind. All of these
factors affect the distance or running time per battery charge. The following are a few suggestions for obtaining the
maximum range per charge.
! Always fully charge the batteries prior to your trip.
! Maintain 35 psi (2.4 bar) in pneumatic drive wheels.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. BothAGM and Gel-Cell are deep-cycle
batteries that are similar in performance.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or Gel-Cell batteries to
reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium batter-
ies (nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain
down their charge, and then accept a relatively quick recharge.AGM and Gel-Cell batteries should be charged as often as
possible. They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encoun-
ter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the
power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More
importantly, it takes a few “charging cycles” (a partial drain—then a full recharge) to establish the critical chemical
balance that is essential to the battery’s peak performance and long life. It is well worth it to take the time to break in
your battery properly.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
How can I ensure maximum battery life?
Afully charged, deep-cycle battery provides reliable performance and extended battery life. Keep your power chair’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
35
V I I . B A T T E R I E S A N D C H A R G I N G
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least
once a week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect
the battery harnesses and store the power chair in a warm, dry environment.Avoid temperature extremes, such as freezing
and excessively hot conditions, and never attempt to charge a frozen battery.Acold or frozen battery should be warmed
for several days prior to recharging.
NOTE: If you are storing a power chair for an extended period of time, you may wish to block the unit up with
several boards under the frame. This keeps the tires off the ground and prevents the possibility of flat spots
developing in the tires.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are
FederalAviationAdministration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s
specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the
original shipping container and ship the batteries in separate boxes.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I I I . C A R E A N D M A I N T E N A N C E
CARE AND MAINTENANCE
Your Quantum 1122 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks.
You can perform some of these checks, but others require assistance from a Quantum Rehab Specialist. Preventive
maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that
your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or
operation, contact your Quantum Rehab Specialist.
WARNING! Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements.Avoid damp areas of any kind.
WARNING! Direct or prolonged exposure to water or dampness could cause the power chair to
malfunction electronically and mechanically. Water can cause electrical components to corrode
and the chair's frame to rust. Power chairs should be examined periodically for signs of corrosion
caused by water exposure, bodily fluid exposure, or incontinence. Damaged components should
be replaced or treated immediately.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to a Quantum Rehab Specialist. Power chairs that are fre-
quently exposed to sources of water, such as incontinence, should be inspected often for corrosion and electronic
components may need to be replaced frequently.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature.Always keep your power
chair between the temperatures of 18°F (-8°C) and 122°F (50°C).
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a
number of factors, such as battery charge, usage, and composition of the batteries (e.g.,AGM or Gel-Cell).
! Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reduced speed
is a safety feature built into the controller that helps prevent damage to the motor and other electrical components.
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors on the electronics tray to ensure that they are all tight and secured properly.
! Make sure the drive tires are inflated to 35 psi (2.4 bar).
WARNING! Make sure your tires are inflated to 35 psi (2.4 bar). Do not underinflate or overinflate
your tires. Low pressure may result in loss of control, and overinflated tires may burst. Overinflating
tires can cause them to explode.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
37
V I I I . C A R E A N D M A I N T E N A N C E
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain
its high-gloss appearance.
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery
well, with the battery terminals facing inward, toward each other. Refer to the frame decal for the correct wiring layout.
WARNING! Even though the power chair has passed the necessary testing requirements for ingress
of liquids, you should keep electrical connections away from sources of dampness, including
direct exposure to water or bodily fluids and incontinence. Check electrical components frequently
for signs of corrosion and replace as necessary.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the center
when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot. Do
not handle or try to repair it. See your Quantum Rehab Specialist if there is a problem.
! Visually inspect the controller harnesses. Make sure that they are not frayed or cut or have any wires exposed. See
your Quantum Rehab Specialist if there is a problem with any of these harnesses.
Weekly Checks
! Disconnect and inspect the controller and the charger harnesses from the electronics tray. Look for corrosion. Contact
your Quantum Rehab Specialist if necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see a Quantum
Rehab Specialist for replacement of the tube.
! Check the brakes. This test should be carried out on a level surface with at least three feet of clearance around your
power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.You must be
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,
pushing the joystick backwards, then left, and then right.
Monthly Checks
! Check that the anti-tip wheels do not rub the ground when you are operate your power chair.Adjust them as neces-
sary. See V. “ComfortAdjustments.”
! Check for extreme wear on the anti-tip wheels. Replace them as necessary.
! Check for drive tire wear. See a Quantum Rehab Specialist for repair.
! Check the rear casters for wear. Replace them as necessary.
! Check the rear forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings
replaced. See a Quantum Rehab Specialist for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to a Quantum Rehab Specialist for yearly maintenance, especially if you use your power chair on a
daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I I I . C A R E A N D M A I N T E N A N C E
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries
from the power chair. See VII. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored without
a full charge may be permanently damaged, causing unreliable performance and limited service life. It is recommended that
you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of
prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the
tires contacting the ground.
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local
waste disposal agency or a Quantum Rehab Specialist for information of proper disposal of power chair packaging, metal
frame components, plastic components, electronics, and batteries.
Cleaning Instructions
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair.Avoid using
products that may scratch the surface of your power chair.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your
product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning
agent before applying it to your product. Failure to comply may result in skin irritation or premature
deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power
chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a
damp cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, replace the tube. If your chair is equipped with a solid tire insert, then
replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through your
Quantum Rehab Specialist.
WARNING! Be sure that the power to the controller is turned off and the power chair is not in
freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the
tire. If any further disassembly is required, deflate the tire completely or it may explode.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
39
V I I I . C A R E A N D M A I N T E N A N C E
TIRE
TUBE
REARRIMHALF
SCREWS
DRIVE WHEEL NUT
FRONT RIM HALF
DRIVEWHEELWASHER
Figure 27. Quantum 1122 DriveWheel
Figure 28. Quantum 1122 DriveWheel Disassembled
Follow these easy steps for a quick and safe repair for both solid and pneumatic tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 27.
5. Pull the wheel off the axle.
6. Remove the screws from the rim assembly and separate the front and rear rim. See figure 28.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is
a solid tire.
8. Reassemble the rims and reinstall the screws.
9. Slide the wheel back onto the axle.
10. Reinstall the drive wheel nut and washer into the axle and tighten.
11. Inflate the pneumatic tires to 35 psi (2.4 bar).
12. Remove the power chair from the blocks.
Battery Replacement
Adiagram is printed on a decal on your power chair frame near the battery tray.
WARNING! Do not replace the batteries when the seat is occupied.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Do not mix or match new and old batteries. If you encounter a situation where one
battery needs to be replaced, then replace both batteries. Refer to the specifications table in this
manual and the manual supplied with the battery charger for recommended type and capacities.
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure the freewheel levers are in the engaged position. See III. “Your Power Chair.”
3. Remove the detent pin from the bottom of the foot frame.
4. Lift the foot frame straight up to remove it from the mounting bracket.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
V I I I . C A R E A N D M A I N T E N A N C E
5. Locate the battery harness on each battery.
6. Disconnect the battery harnesses from their respective
quick disconnects on the frame by pulling the quick
disconnects toward you.
7. Remove the batteries from the power base assembly.
8. Disconnect the battery harnesses from the positive and
negative terminals on the batteries. See figure 29.
9. Connect the battery harnesses to the new batteries.
! Connect the wire labeled BAT (+) to the positive
(red) terminal.
! Connect the wire labeled BAT (-) to the negative
(black) terminal.
10. Place the rear battery at the back of the battery tray
with the battery terminals facing inward, toward the cen-
ter of the power chair and plug the battery harness into
a quick disconnect.
Figure 29. Battery Connections
11. Place the front battery in the battery tray with the battery terminals facing inward, toward the center of the power chair
and plug the battery harness into a quick disconnect.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
12. Replace the front cover and use the detent pin to secure.
When to See Your Quantum Rehab Specialist for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your Quan-
tum Rehab Specialist. When calling, have the model number, serial number, nature of the problem, and the trouble
code if available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Jerky motion
! Uneven wear on any of the tires
! Pulling to one side
! Bent or broken wheel assemblies
! Powers up, but does not move
! Does not power up
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,
contact your Quantum Rehab Specialist.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
41
I X . W A R R A N T Y
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Structural frame components, including:
! Main Frame
! Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
Electronic components, including:
! ChargerAssembly
! Controller
Main frame assemblies, including:
! Anti-tip forks ! Caster forks
! Caster beam ! Metal seat framing
! Joystick
Other components, including:
! Foot riggings
! Electrical Harnesses ! Foot rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Motor/gearbox assembly ! Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Accessories
! Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Bearings and bushings
! Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not
warranted by Pride.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
I X . W A R R A N T Y
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
! ABS Plastic shrouds
! Motor brushes
! Upholstery and seating
! Brake Pads
! Tires and tubes
! Fuses/Bulbs
! Circumstances beyond the control of Pride
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized, IN
ADVANCE, by Pride Mobility Products Corporation
! Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by a Quantum Rehab Specialist. Do not return faulty parts to Pride without prior
written authorization.All transportation costs and shipping damage incurred while submitting parts for repair or replace-
ment are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride product can
result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase and to the extent permitted by law.Any and all implied warranties are excluded. This is the exclusive
remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation
incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible technical
and customer service.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
43
N O T E S
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
N O T E S
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
45
N O T E S
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 1122 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Quality Control - Quantum 1122 Series
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*I NFMANU2923*
Product Serial #
Download from Www.Somanuals.com. All Manuals Search And Download.
|