R
R
Low Impact Climber
with Pulse*
Owner’s Manual
Assembly and Operation
*Several versions of this owner’s manual exist. This
is a copy of the last version published. If the
assembly instructions do not coincide with your
718e/723e, please call Precor Customer Service.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Unpacking the 718e or 723e Low Impact Climber .....................................
4
Assembling the 718e or 723e Low Impact Climber ...................................
Installation Requirements ....................................................................
Assembly Instructions .........................................................................
6
6
6
Using the Precor 718e or 723e Low Impact Climber ................................. 17
Understanding the Electronic Console ................................................. 17
Displays ............................................................................................ 17
Keys ................................................................................................. 18
Setting the Resistance Level................................................................ 19
Setting a Pacer .................................................................................... 20
Using the Pulse Feature ....................................................................... 20
Pausing Your Workout ........................................................................ 21
Ending a Workout. ............................................................................... 21
How to Use the 718e or 723e Climber ................................................. 21
Working Out on the 718e or 723e Climber .......................................... 21
Sample Exercise Routines ................................................................... 23
General Aerobic Training Information ....................................................... 24
How Hard Should I Exercise? .............................................................. 25
How Long Should I Exercise?.............................................................. 26
How Often Should I Exercise? ............................................................. 26
Maintenance and Troubleshooting ............................................................ 27
Cleaning the Climber ........................................................................... 27
Changing the Batteries......................................................................... 27
Troubleshooting Tips........................................................................... 27
Obtaining Service ..................................................................... Back cover
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking the 718e or 723e Low Impact Climber
All Precor products are thoroughly tested and inspected before shipment. The
climber is shipped in the following pieces:
•
•
•
•
•
•
•
base
upright support (long column)
base column support (short column)
resistance cylinders
handrail console
electronic console display
hardware kit, Owner’s Manual, and limited warranty card (not shown in
Diagram 1)
Diagram 1
Unpacking the climber.
Upright support (long column)
U S A
R
Base column support
(short column)
Base
Electronic console display
R
Resistance cylinders
Handrail console 718e only
Handrails 723e only
Unpack the climber and place all the pieces on the floor. For help in identifying
the various pieces, refer to Diagram 1. The packet containing the hardware kit,
Owner’s Manual, and limited warranty card is not shown.
Important: Do not pinch or crimp the reed switch cable during the unpacking
and assembly process. The rope attached to the upright assembly is used to
install the reed switch cable. Do not remove the rope from the upright
assembly at this time. Do not cut the wire ties holding the stair arms to the
upright support.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 2
Hardware kit.
B
E
F
J
A
G
C
D
H
I
Open the hardware kit and identify the following items. Diagram 2 provides an
overview of the kit’s contents. As you identify the contents of the kit, check them
off below:
(A) Two gaskets for frame base
(B) Four frame-to-base bolts
(C) Four large flat washers (718e only)
(D) Four lock nuts
(E) Two small bolts (718e only) Four small bolts (723e only)
(F) Two phillips-head screws
(G) One 3/16" hex key
(H) Two 1/2" wrenches
(I) Two AA batteries
(J) One 5/32" hex key (723e only)
If any items are missing, contact your authorized Precor dealer. For the dealer
nearest you, call 1-800-4-PRECOR.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the 718e or 723e Low Impact Climber
The information in this section provides instructions regarding the assembly of
the 718e or 723e Low Impact Climber. You should carefully read and follow the
instructions in this manual. If you do not assemble and use the climber
according to the following guidelines, you could void the Precor limited
warranty.
Installation Requirements
Follow these installation requirements when installing the climber:
•
•
Set up the 718e and 723e climber on a solid, flat surface.
Fill out and mail the limited warranty registration card. The serial number
is located on the underside of the climber’s base. It is also located on a
label on the outside of the box.
Assembly Instructions
To assist you in the assembly of the 718e or 723e climber, the items in the
hardware kit, shown in Diagram 2, correspond to a particular letter in the
alphabet. These letters appear throughout the assembly instructions. Refer to
Diagram 2 while performing the steps below.
Note: You will need scissors and a phillips-head screwdriver to complete the
assembly process.
Diagram 3
Place frame on base.
Upright support
Stair arm
Front crossbar
Blocks or books
Base
1. Place Upright Support on Base. (Diagram 3) To install the upright support
(long column that has the stair arms attached) take the following steps:
Important: Do not remove the rope from the upright support. It is used to
feed the reed switch cable through the upright support column.
a. Place the base at or near the location where you will be using the
climber. Lift the base onto wooden blocks or large hardcover books.
This helps you access the underside of the base. Make sure that the
rubber pads on the crossbar are facing the floor.
b. Position the upright support (long column) onto the base.
Note: Be sure to align the upright support and base properly. The
front crossbar and upright support mounts are very close together as
shown in Diagram 3.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Remove a gasket (A) from the hardware kit. Align the upright support
with the mounting holes in the base. Place the gasket between the
upright support mount and base.
Diagram 4
Attach frame to base.
Upright support
Washer (C)
Gasket (A)
Bolt (B)
Weld
Base
Front crossbar
d. Take two frame-to-base bolts (B) from the hardware kit and place a
washer (C) on each. Insert the bolts through the upright support
mount, gasket, and base. Make sure that the front mount is adjacent
to the crossbar weld, but not on top of the weld. See Diagram 4.
Attach a lock nut (D) to the opposite end of each bolt. Hold the lock
nut with the socket wrench (H) while you firmly tighten the bolts with
the other wrench (H) provided.
Important: Perform the following step on one stair arm at a time.
CAUTION: To avoid injury and
ensure the integrity of the
unit, do not drop the stair arm
onto the rear crossbar.
e. Hold onto the stair arm’s footpad with one hand while you use
scissors (in the other hand) to cut the plastic wire tie that secures the
stair arm to the upright support. Carefully lower the stair arm onto the
rear crossbar. Perform the same step for the other stair arm.
Note: If the upright support is mounted properly, the footpads on the
stair arms rest on the rear crossbar.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 5
Pull reed switch cable through
upright support.
Rope (718e only)
Plastic wire tie (723e only)
Upright support
Reed switch cable connector
Reed switch cable
2. Feed Reed Switch Cable through Upright Support. (Diagram 5) Remove
the bolts from the base column support (short column) and set them
aside. The gasket should hang on the reed switch cable. Take the following
steps to install the reed switch cable:
a. Cut the wire tie from around the reed switch cable and, if necessary,
gently pull the cable out of the roller guard. Place the short column
near the upright support so that the gasket and roller guard face the
rope.
b. Ask an assistant to hold the base column support. This lets you have
both hands free to manipulate the rope (718e only)/plastic wire tie
(723e only) and cable.
c. Securely tape the reed switch cable connector to the end of the rope
(718e only)/plastic wire tie (723e only) and feed the cable through the
upright support (long column) as you carefully pull the rope (718e
only)/plastic wire tie (723e only) out from the top. Tape the reed
switch cable to the top of the upright support and set the rope (718e
only)/plastic wire tie (723e only) aside. (On the 718e you will use the
red rope in step 12.)
Note: You may need to tip the climber onto its side if the cable
disengages from the rope/plastic wire tie. A hex key is helpful in
locating the cable inside the column and in pulling it through the hole
at the top.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 6
Attach base column support to
upright support.
Reed switch cable connector
Upright support
R
U S A
718e
Gasket
Base column support
(short column)
CAUTION: Make sure you do
not crimp the reed switch
cable when you tighten the
base column support onto the
upright support because you
could void the manufacturer’s
limited warranty.
3. Secure Upper Frame Pieces Together. (Diagram 6) Gently pull the reed
switch cable from the top of the upright support as you align the bolt holes
in the upright support with the base column support and gasket. Insert the
two mid-frame bolts that you set aside in step 2. Thread the bolts through
the upright support and into the short column. Fully tighten the bolts using
the hex key (G) provided, but be careful not to pinch the cable.
Diagram 7
Install base column support to
base frame.
Base column support (short column)
Washer (C)
Base column support mount
Gasket (A)
Bolt (B)
Rear crossbar
4. Attach Base Column Support to Base. (Diagram 7) Place a washer (C)
onto each of the two remaining frame-to-base bolts (B). Place the
remaining gasket (A) between the base column support mount and the
base frame. Align the holes and insert the bolts and washers through the
base column support mount and the climber base. Attach a lock nut (D) to
the end of each bolt. Hold the lock nut with the wrench (H) while you firmly
tighten the bolts with the other wrench (H) provided.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 8
Attach resistance cylinder to
upright support.
Upper axle
Spacer
Washer
Bolt
Upright support
Adjustment portion
1
2
5
3
4
Resistance cylinder
Indicator arrow
5. Attach Resistance Cylinders to Upright Support. (Diagram 8) Remove the
bolt, washer and spacer from the upper axle using your fingers or the hex
key (G) provided. With the indicator arrow (See Diagram 8) facing toward
the footpad, slide the top of the resistance cylinder onto the upper axle.
Place the washer and spacer on the bolt. Reinsert the bolt and tighten
securely using the hex key provided. Repeat this same step to attach the
other resistance cylinder.
Diagram 9
Remove bolts from lower
resistance cylinder mounts.
Bolt
Washer (718e only)
U-shaped mount
Nut
Stair arm
6. Connect Resistance Cylinders to Stair Arms. (Diagrams 9 and 10) The
washers, nut, and bolt need to be removed from the lower resistance
cylinder mount (U-shaped mount) before connecting the resistance
cylinders. See Diagram 9. Remove the bolt using your fingers or the
supplied wrench (H). To mount the lower resistance cylinders to the stair
arms, take the following steps:
Note: Perform the following steps on one stair arm at a time.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 10
Attach resistance cylinder to stair arm.
Bolt
Washer (718e only)
Resistance cylinder mount
Bushing
U-shaped mount
Nut
Stair arm
a. Align the resistance cylinder with the holes in the U-shaped mount
and slide the resistance cylinder into position. See Diagram 10.
b. Insert the bolt through the U-shaped mount and resistance cylinder.
Use the wrench (H) to hold the nut in place while you tighten the bolt
securely using the other wrench (H).
c. Repeat step 6 to mount the other resistance cylinder.
Diagram 11
Install handrail for the 718e only.
Bolt (E)
Reed switch cable
Handrail console
Handrail
Upright support
CAUTION: The reed switch
cable should slide easily
through the upright support.
Do not tug on the cable
because you could void the
manufacturer’s limited
warranty.
7. Install Handrail. (Diagram 11 or 12) The 718e has a different handrail than
the 723e climber. Follow the appropriate steps below to mount the
handrails.
a. 718e Handrail. Take the two small bolts (E) from the hardware kit.
Position the handrail console (flat surface of the console should face
up) on top of the upright support and feed the reed switch cable
through the large hole in the handrail console. Tape the connector to
the top of the console. Align the bolt holes and secure the handrail
console to the frame by inserting the bolts through the top of the
handrail console and into the upright support. Tighten the bolts firmly
using the hex key (G).
Important: Pull gently on the excess cable as you feed the cable through
the large hole in the handrail console. If the cable does not move freely,
check to be sure that the cable is not pinched or crimped between the long
and short column mounts. See step 3.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 12
Install handrail for the 723e only.
Upper handrail
Bolt
Console
Ribbon cable connection
Tighten bolts
Lower handrail
b. 723e Handrail. Take the four small bolts (E) from the hardware kit.
Position the handrails as shown in Diagram 12. Slide one handrail into
the mounting tube at a time so that the foam wrap on the handrail
touches the console. See Diagram 12. Once both handrails are in
place, insert the bolts and tighten firmly using the hex key (J). See
inset in Diagram 12.
Diagram 13
Install electronic console (723e only).
Electronic console
Handrail console
Phillips-head screws
8. Install Electronic Console. (Diagram 13 and 14) To attach the electronic
console display to the handrail console, take the following steps:
a. Plug the slotted reed switch cable connector into its receptacle on the
underside of the electronic console display.
b. Hold the electronic console display above the handrail console while
you gently feed any excess cable back through the hole in the handrail
console.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 14
Install electronic console (718e).
Electronic console
Phillips-head screws
Handrail console
c. Align the holes and insert two phillips-head screws (F) on the
underside of the handrail console.
d. Tighten the screws using your phillips-head screwdriver.
Diagram 15
Install the batteries
AA battery case
Battery drawer
R
U S A
9. Insert Batteries. (Diagram 15) Find the drawer on the side of the electronic
console and press in lightly to open it. Pull the drawer out with your
fingers. Take the following steps to insert the batteries:
a. Slide the drawer out to expose the battery case. Place the two “AA”
alkaline batteries (found in the hardware kit) into the case. Align the
batteries to the proper polarity (+ and - indicators are inside the
battery case). The entire display lights and the console beeps.
b. Close the battery drawer by pushing it gently into the electronic
console.
c. Press START/STOP to activate the timer (TIME display). Press RESET
to “reset” the displays to zero. For more information, refer to the
section titled, Understanding the Electronic Console.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 16
Location of magnet and reed switch.
Resistance cylinder
Base column support
Left stair arm
Magnet
Reed switch
R
Gap 1/8" to 1/4"
USA
(.3 to .6 centimeters)
10. Check Operation of Electronics. (Diagram 16) Make sure that the spacing
between the magnet on the left stair arm and the reed switch on the rear
short column is correct. If the spacing is incorrect, the electronic console
display will not operate properly. The distance between the magnet and the
reed switch should be about 1/8 inch (.3 centimeters). If the spacing is not
correct, adjust the spacing by moving the reed switch in or out of the
column with your fingers.
11. Set the Resistance. Adjust the stair arm resistance by turning the top of
the resistance cylinder until the triangle on the resistance cylinder points to
the “2” on the adjustment knob. Do the same for the other stair arm. Make
sure that the resistance on both stair arms is at the same setting.
Diagram 17
Align stair arms with label (718e only).
Rope
Precor label red box
Stair arm footpad
R
R
U
S
A
Rear crossbar
12. Install Rope—718e only. (Diagrams 17, 18 and 19) To properly install the
red rope (set aside in step 2), get a marker (pen or pencil) and take the
following steps:
a. Feed the rope up through the right stair arm mount. (Determine right
and left while standing behind the rear crossbar and facing toward the
electronic console.)
b. Move both stair arms so that the top of the stair arms line up with the
red box located on the Precor label. See Diagram 17. Have an
assistant hold the stair arms in place while you route the rope through
the pulley.
Note: It may be easier to install the guide rope if the climber is placed
on its right hand side on the floor. This will expose the underside of
the stair arms and provide easier accessibility.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 18
Install the guide rope (718e only).
Pulley
Finger guard
Stair arm
Right stair arm mount
Guide rope (718e only)
c. Loop the rope over the pulley (through the finger guard on both sides
of the pulley) and down into the left stair arm mount. See Diagram 18.
Diagram 19
Mark the guide rope (718e only).
Guide rope (718e only)
Pencil or pen mark
Left stair arm mount
CAUTION: Do not stand on
the stair arms while
d. Pull the rope taunt and mark the rope where it meets the stair arm
mount. See Diagram 19.
performing these steps. Prior
to working out, the tension on
the guide rope must be set
properly to avoid damaging
the resistance cylinders and
voiding the manufacturer’s
limited warranty.
Important: Before you mark the rope, be sure that the top of both stair
arms line up with the top of the red box on the Precor label. Refer to
Diagram 17 on page 14.
e. With the rope running through the stair arm mount, move both stair
arms up so that you can easily tie a knot where you marked the rope.
Note that if you placed the climber on its side to install the rope,
return the climber to an upright position with the base flat on the
floor.
f. Check the length of the guide rope by returning the stair arms to an
even position shown in Diagram 17 on page 14. The top of both stair
arms should line up with the red box located on the Precor label.
CAUTION: Check the knots
and the length of the rope
before standing on the stair
arms. You cannot re-tie the
knots once you stand on the
stair arms.
g. Step onto the stair arms. Test the stair stroke by moving your legs up
and down a few times.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 20
Measure the distance of the resistance
cylinders from the mounts (718e only).
1/4" to 1/2"
(.6 to 1.2 cm)
Adjustment knob
Resistance cylinder mount
5
1
4
2
h. Press the right footpad down onto the rear crossbar. Let the left stair
arm move up into its highest position (away from the rear crossbar).
Check the distance between the top of the resistance cylinder on the
left stair arm and the upper axle. It should be between 1/4 to 1/2
inches (.6 to 1.2 centimeters). See Diagram 20.
If the distance is correct, you have installed the rope properly. If the
adjustment knob touches the resistance cylinder mount, you will need
to replace the rope and readjust the length.
Note: To obtain a new rope call your local Precor dealer at 1-800-4-
PRECOR.
Every time you use your climber, make sure that all frame-to-frame and frame-
to-base bolts are still tight. If there is any movement, firmly retighten all bolts.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Precor Low Impact Climber
In addition to providing an excellent cardiovascular workout, one of the
advantages of the Precor climber is that it is simple to use. With very little time
or practice, you can learn how to use it effectively. This section provides
information and instructions about the following:
•
•
•
•
•
•
•
using the electronic console
setting the resistance level
setting a pacer
pausing your workout
ending a workout
exercising on the climber
reviewing sample exercise routines
Understanding the Electronic Console
Once you have assembled your climber, it is ready to use. There are no complex
instructions to follow or mandatory programming steps required to operate the
climber—the electronic display is there only for reference. It provides motivat-
ing feedback about your workout to help you monitor your progress and meet
your fitness goals.
The console’s convenient “hands free” function lets you start and end a workout
without touching any keys. Simply step onto the climber to begin your workout.
The displays automatically appear and begin providing information about your
workout. To select a specific informational display, such as TIME or TOTAL
STEPS, press the MODE key until the desired information appears on the
display.
Diagram 21
Electronic console display
Diagram 21 shows the electronic console display. An explanation of the eight
display features and four keys are explained below.
Displays
STEPS/MIN—appears as the smaller numeric display to the left of the main
numeric display and indicates your steps per minute, up to 99. If you have not
set a pacer, the bar graph on the left side of the display can also provide similar
information (up to 150 steps—see Setting a Pacer).
Note: If the display remains at zero when you move the stair arms, check that
the reed switch along the left side of the short column is correctly aligned. Refer
to step 10 in the Assembly Instructions.
TOTAL STEPS—shows the total number of steps during a workout, up to a total
of 9,999. You can use this display to measure total work accomplished in a
workout.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ODOMETER X 100—indicates the total number of steps accumulated on the
climber over time, up to 999,900. This display appears with the TOTAL STEPS
display. Use the odometer to track the amount of “mileage” your climber has on
it. Note that you need to multiply the number that appears by 100.
TIME—functions like a stopwatch, giving you total exercise time per session, up
to 59 minutes and 59 seconds. The TIME display starts or stops automatically
when you start or stop a workout. You must press the RESET key to reset the
TIME display to 0. (For more information about RESET, see the explanation
under Keys.) Use the TIME display to keep track of how long you have exercised
in a given session.
Note: If you pause during a workout, the internal clock continues to count and
to display the time for another 5 minutes. After 5 minutes, the screen saver
feature takes over, saves your workout statistics, and shuts off the displays. If
you return to your workout before 5 minutes elapse, the time display reverts to
your actual workout time. Refer to Pausing Your Workout.
SCAN—alternates between the displays STEPS/MIN, TIME, TOTAL STEPS,
TOTAL CALories, and PULSE every few seconds. When you press the RESET
key or begin a workout by pressing the START/STOP key, the word SCAN
appears on the display and indicates that you are in SCAN mode. If you only
want one particular feature displayed, press the MODE key until the feature is
highlighted. See MODE under Keys below.
PACER—appears in the bar graph on the left of the electronic display. You can
select a pacer up to 150 steps per minute. When you maintain or exceed the
pacer’s step rate, the bar stops blinking. The pacer sets a tempo for you to
follow which provides motivation and helps you to maintain your exercise
intensity.
TOTAL CALORIES—displays an estimate of the number of calories being burned
during your workout. The estimate is based on a 150 pound (68 kg) person
working out at your current steps per minute.
PULSE—shows your heart rate if you have installed the Precor receiver and put
on a Precor/Polar chest strap or attached the pulse detector (Precor’s ear clip
option) to the console. When you attach the receiver and put on the chest strap
or plug the pulse detector into the console, a appears on the display at the
bottom right corner.
Keys
START/STOP—starts and stops a workout session. However, the electronic
console automatically begins displaying information when you move the stair
arms. You could use this key to start or stop your workout when you want to
keep your warm-up or cool-down sessions separate from your workout
statistics.
MODE—specifies the information you want displayed; whether its STEPS/MIN,
TIME, TOTAL STEPS, TOTAL CALories, PULSE or SCAN mode. Simply press
this key repeatedly until information from the desired display appears.
PACER—sets a pace tempo. When you press this key the pacer appears in the
bar graph on the left side of the display. To set the pace tempo or change the
current pacer setting, press the PACER key until the desired step rate is
highlighted. Refer to Setting a Pacer.
RESET—resets the displays on the electronic console to zero. Note that
pressing this key does not reset the ODOMETER display. Using the RESET key is
another way to keep your warm-up or cool-down sessions separate from your
workout statistics.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Resistance Level
CAUTION: Do not adjust the
resistance cylinders after
extended continuous use
because they can heat up to
the point of being
Before using your climber, you need to adjust the resistance level.
Resistance, which is related to your body weight and your step height during
the workout, determines your cadence (the number of steps you can take per
minute). The relationship between body weight, step height, and cadence
determines how hard you work during a session.
uncomfortable to touch.
Understanding the principles covered in General Aerobic Training Information
starting on page 24 will help you select the appropriate resistance for your
fitness level and personal fitness goals. To achieve your goals, it is important to
use a resistance that allows your heart rate to reach your training zone (see
Diagram 26 on page 25) and then maintains that rate for the desired length of
time—while you maintain a step height between 4 to 8 inches. (For information
about your training zone, see How Hard Should I Exercise? in General Aerobic
Training Information.)
Keep these guidelines in mind when adjusting the resistance cylinders:
•
•
Resistance settings on the climber range from 1 to 12.
“1” provides a faster cadence (step rate) due to less resistance in the stair
arms than “12.”
•
The resistance cylinders operate more stiffly at the beginning of a workout
until they warm up. You may want to re-adjust the resistance settings after
working out for about 5 minutes.
Diagram 22
Setting the resistance level.
Resistance setting
Adjustment knob
5
1
Number
4
2
Indicator arrow
Resistance cylinder
To adjust the resistance level, take the following steps:
CAUTION: Make sure that both
cylinders are set at the same
resistance to ensure a
1. When beginning your workout, warm up by setting the resistance between
1 and 3. Turn the top of the resistance cylinder so that the number aligns
with the arrow. See Diagram 22.
smooth, balanced feel during
your workout.
2. Repeat step 1 for the opposite stair arm. Make sure that both resistance
cylinders are set on the same number to ensure equal resistance.
Note: Allow the resistance cylinders to warm up for at least 5 minutes
before raising the resistance setting. After which, you can adjust the
settings anytime during your workout. However, after extended, continu-
ous use, the resistance cylinders can heat up to the point of being
uncomfortable to touch.
Start exercising at a low setting. Gradually work your way to a comfortable
resistance level and into your target heart rate zone (see Diagram 26, page 25).
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a Pacer
Setting a pace tempo provides motivation and helps you to maintain your
exercise intensity. To set a pacer, press the PACER key until the bar graph
highlights the desired step rate. The bar graph provides incremental markings
every 15 steps (15, 30, 45..., to 150). If you bypass the mark that you want to
set, continue to press the PACER key. It will cycle around to zero and you can
start over. Note that the pacer stops blinking when you maintain or exceed the
pacer’s step rate.
Using the Pulse Feature
With the Precor pulse feature, you can use the display to help maintain your
heart rate in its training zone. Diagram 26 on page 25 shows your target heart
rate or training zone. To receive the best possible cardiovascular fitness level,
you want to maintain your heart rate in your training zone while you workout.
You can use the pulse feature in one of two ways:
Diagram 23
Precor Ear Clip Option Connection
Precor ear clip and Polar heart
rate options
START/STOP
RESET
Precor/Polar Chest Strap
MODE
PACER
R
Precor Ear Clip
•
•
Precor Ear Clip Option. A pulse detector plugs into the electronic console.
Your pulse is detected once you attach the ear clip to your ear lobe.
Precor Heart Rate Option. The receiver plugs into the electronic console.
When you wear the chest strap the console displays your heart rate.
To use the pulse feature, plug the pulse detector into the electronic console and
attach the ear clip to your ear lobe. See Diagram 23. Or, if you have a Precor/
Polar chest strap, put it on and plug the receiver into the electronic console.
Note: A appears in the lower right corner of the display when you plug the
pulse detector in or attach the receiver and put on the Precor/Polar chest strap.
Follow the workout instructions on the following pages. Use the MODE key to
highlight SCAN mode or to select the PULSE display.
Important: Your heart rate will not appear if the pulse detector or chest strap
cannot transmit a heart beat. This can occur if you remove the ear clip (or chest
strap) or the ear clip (or chest strap) becomes dislodged. Occasionally, due to
medication, caffeine, or physiology of the heart (such as an irregular heart beat)
the receiver in the console cannot correctly detect a heart beat. Verify the
accuracy of the heart rate reading by taking your pulse one or twice during your
workout. For additional information, review the Owner’s Manual that accompa-
nied your Precor Heart Rate Option.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Pausing Your Workout
Since the climber has an automatic auto-pause feature, you can pause during
your workout to answer the telephone or take a short rest. To pause your
workout, simply stop stepping on the climber. Five minutes after you stop
exercising the electronics unique screen-saver feature turns off the display and
saves your position. When you resume your workout and step on to the climber,
the displays continue from the point you left off and provide an accurate readout
of your total workout time.
Note: When you pause, the internal clock causes the TIME display to continue
counting. If you return to your workout before 5 minutes elapse, the TIME
display reverts back to your actual workout time.
Ending a Workout
To end your workout, simply stop stepping. You can also press the START/
STOP key. In either case, the displays on the console freeze, allowing you to
review your workout statistics.
You can then do one of two things: either press RESET to return the displays to
zero or let them stand, which lets you track total exercise time and steps over
several exercise sessions. The electronics count TIME, TOTAL STEPS, and
TOTAL CALories cumulatively, so if you do not press RESET at the end of your
workout, the electronic console will continue counting from the point you left
off.
With the console’s unique screen-saver feature, you do not have to worry about
turning OFF the console when you finish your workout. Five minutes after you
stop exercising the screen-saver turns OFF the display.
How to Use the Climber
This section explains how to work out on the climber safely and effectively.
When using the climber, follow these general guidelines:
•
•
•
•
•
At the beginning of a workout, warm-up by taking several minutes to bring
your heart rate into your training zone (see Diagram 26 on page 25).
After your workout, walk slowly for several minutes to cool down your
body and lower your pulse rate.
Protect your knees by keeping them directly over your toes. Avoid taking
steps that are too big or bending your knees beyond 90 degrees.
Keep your feet on the black footpads—moving your feet too far forward
might cause you to bump the cylinders with your knees.
Keep your shoulders and back relaxed. Hold your head up—looking at your
feet or the floor strains your neck and back muscles. Avoid bouncing or
swinging your hips from side to side.
•
•
Set the resistance at a low level initially until your muscles warm up and
your heart rate reaches its target zone. You can then increase the level to
the desired setting for working out.
Gently stretch your lower body and back after a workout to help prevent
stiffness or soreness.
CAUTION: Before beginning
any fitness program, have
your physician give you a
complete physical exam.
Working Out on the Climber
To use the climber, take the following steps:
1. Press RESET on the electronic console and hold for 3 seconds. Release the
key at the “beep” sound. Press MODE until the TIME function is highlighted
and the TIME display appears.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 24
Working out on the 718e climber.
2. After you have set the resistance level at a low setting and finished any
desired pre-workout stretching, step onto the climber. Make sure that your
weight is balanced and your hands and feet are positioned securely. Refer
to How to Use the Climber.
3. Start your workout by taking steps 4 to 8 inches in height, at a cadence
that will allow your heart rate to reach your training zone within 5 minutes.
See Diagram 24. To get your heart rate into your training zone, you might
have to adjust the resistance setting.
Note: To increase your heart rate, increase the step speed by adjusting the
resistance cylinder to a lower setting. To slow your heart rate, slow the
step speed by moving to a higher setting.
4. After your warm-up period, maintain your heart rate in your training zone
during your aerobic session. As you work out, vary your body position to
reduce localized muscle fatigue and to exercise all your lower body
muscles. See Sample Exercise Routines.
5. When you are finished exercising, cool down for 3 to 5 minutes by
gradually reducing your step rate and height. If earlier you decreased
resistance for your aerobic session, move the resistance level to a higher
setting to help your body cool down. A proper cool-down helps to
transport excess lactic acid out of the working muscles, allowing them to
recover faster.
6. To end your workout, simply stop stepping. You can also press the START/
STOP key. In either case, the displays on the console freeze, allowing you
to review your workout statistics. Press RESET to return the displays to
zero or let them stand, which lets you track exercise time and steps over
several sessions. Five minutes after you stop exercising, the display
automatically turns OFF.
For best results, vary your workouts by changing duration, intensity, footstep,
body position and type of work (such as interval training). Keep track of your
workouts by writing them down so you can monitor your progress toward your
fitness goals and use the information to plan interesting and challenging
workouts.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample Exercise Routines
CAUTION: Before beginning
any fitness program, have
your doctor give you a
complete physical
For a good upper body workout, set the resistance cylinders at a moderate
level—between the markings 4 and 6 and take the following steps:
1. Stand erect with your feet placed firmly on the stair arm footpads.
examination.
2. To maintain your balance after stepping onto the stair arms, place your
hands in a comfortable position on top of the handrails, palms facing
down. You should have a slight bend at your elbows. Do not straighten
your arms out completely and do not place your weight on the handrails,
use the handrails for balance only.
CAUTION: Make sure that both
cylinders are set at the same
resistance to ensure a
3. As you transfer your weight and press down with one leg, the opposite leg
should rise to about a 90 degree angle. Do not raise your leg above a 90
degree angle as you can cause injury to yourself.
smooth, balanced feel during
your workout.
4. Become familiar with the movement of the stair arms. Transfer your weight
between stair arms in one fluid motion. Do not bounce, bob, or rock up
and down or back and forth. Keep your back straight and erect while you
work out.
When you first start out, try a one-minute rest and one-minute work interval.
During the rest interval, you should let your body relax, continuing to transfer
your weight from one stair arm to the other with your hands relaxed, yet
maintaining your balance holding onto the handrails. During the work interval,
concentrate on your movement, keeping your knees bent, pushing down and
lifting up, in one continuous motion.
CAUTION: Throughout your
workout, periodically check
your heart rate. Never allow
your heart rate to exceed 80%
of your training zone. Refer to
Diagram 26 on page 25 to
determine the training zone
that is appropriate for your
age group.
Calf muscle workout—during your downward stroke, as the pedal tails away,
let your heel come off the foot pedal. This helps work your calf muscle group.
Gluteal and Hamstring workout—Bend your arms at the elbow and place them
along the upper length of the handrail. Bend your body at the hips while you rest
your arms on the handrails. Then, keep your back straight while you bring your
knees up toward your chest to begin working your gluteals and hamstrings.
Remember, do not bend your knees more than 90 degrees, as you can cause
injury to yourself.
Quadricep workout—Hold onto the handrails while you sit back, knees bent,
placing your weight directly over the footpads. You should be able to feel light
pressure on your quadriceps. Do not position your weight so far back that the
front crossbar on the climber comes off the floor. Keep your back straight, in an
upright position, as you take shorter, faster steps. Keep your knees bent
throughout your workout to isolate and work out your quadricep muscles.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
General Aerobic Training Information
A workout on the Precor 718e or 723e climber provides excellent and efficient
cardiovascular conditioning, while strengthening and toning the thighs, calves,
and hips. The darkened areas in Diagram 25 indicate the muscles improved.
Diagram 25
Muscles exercised during a
stair climber workout.
1
1
1. Trapezius
2
3
2. Deltoid
4
3. Pectorals
7
10
5
6
9
4. Rhomboids
8
5. Triceps
6. Biceps
8
11
7. Latissimus Dorsi
8. Forearm Flexors/Extensors
9. Abdominals
10. Erector Spinae
11. Gluteals
12
13
16
14
12. Hip Flexors
13. Quadriceps
14. Hamstrings
15. Gastrocnemius/Soleus
16. Peroneus Longus/Brevis
15
16
To get the most out of each workout, a general understanding of the principles
behind aerobic training is invaluable. The best source of fitness information is
your specialty fitness dealer. In addition to providing information on which
exercise equipment is the best for your individual needs, your specialty fitness
dealer can provide useful advice on training, technique, and exercise physiology.
Your dealer can also recommend good books on these subjects.
To help you get started in planning and carrying out your fitness program, this
section provides some basic information on aerobic exercise—such as how
hard you should work out, how long each session should be, and how often you
need to exercise to benefit from a regular program.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram 26
Heart rate training zones.
HEART RATE TRAINING ZONE
200
195
190
185
180
175
170
165
200
190
180
170
160
160
160
128
104
156
155
152
124
150
148
120
144
145
150
140
140
114
136
111
MAX.
132
107
HEART
RATE
124
101
130
120
100
90
120
97
130
116
94
127
117
80% OF
MAX.
HEART
RATE
65% OF
MAX.
HEART
RATE
80
70
20
25 30 35 40 45 50 55 60 65 70 75
YOUR AGE
How Hard Should I Exercise?
Studies have shown that to achieve the benefits of aerobic exercise, it is
necessary to work out hard enough to raise your heart rate to a certain
minimum level, called the “training zone.” Your training zone depends on your
age and level of fitness.
Diagram 26 shows your recommended heart rate training zone, which is
calculated using your age and your maximum attainable heart rate. The chart is
based on a resting heart rate of about 72 for males and 80 for females. Your
optimum training zone is between 65% and 80% of your maximum heart rate.
For efficient aerobic exercise, work only hard enough to keep your heart rate in
this zone. You will obtain the greatest fat-burning benefits when you exercise
within the optimum training zone.
Pushing yourself beyond the recommended range, (that is, exercising so hard
that your heart rate rises above 80% of maximum) can overstress your
muscles. To increase cardiovascular improvement, exercise longer, not harder.
Keep in mind that this zone is an approximation, to be used as a guideline—
individual heart rates vary according to several physiological factors. To
determine your training zone, find your age on the diagram, and then find the
area where the training zone and your age intersect. For example, if you are 35
years old, your training zone is between 120 and 148 beats per minute.
Remember this zone—this is the heart rate you should try to maintain as you
work out.
To determine your heart rate, take your pulse at a place that you can reach easily
and comfortably while you exercise. Typical places for measuring heart rate are
directly over the heart on the left side of the chest, on either side of the neck,
over the temple, or on the thumb side of either wrist. Wherever you measure
your pulse, make sure that you use your index and middle fingers—not your
thumb. Your thumb has a strong pulse, which can affect your heart rate reading.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Once you locate your pulse, look at a watch or a clock with a second hand and
count the beats for six seconds. Multiply that number by 10 to determine the
total number of beats per minute. For example, if you count 14 beats over six
seconds, the total number of beats per minute is 140. Compare the total number
of beats with your training zone as identified in Diagram 26. If necessary,
increase or decrease your activity level to bring your heart rate into your training
zone. You can increase your activity level by increasing your resistance level and
stepping at a higher cadence. Similarly, lowering the resistance and decreasing
your steps per minute will lower your heart rate. Remember—your heart rate is
the definitive measure of how hard you are working.
Regardless of your fitness level, avoid doing too much too soon. Setting the
resistance level too high, stepping too deeply (taking large steps), or stepping
too quickly for too long are common errors. Give yourself time to become
familiar with your climber and improve your fitness level. Then you can
gradually increase your resistance level and stepping cadence to make your
workouts more challenging.
How Long Should I Exercise?
The length of each exercise session depends on your fitness level. Exercise
physiologists have determined that, to attain cardiovascular benefits from
exercise, you should maintain your heart rate in the training zone for at least 15
minutes. This does not include warm-up and cool-down time. You should
always allow several minutes to bring your heart rate into the training zone, by
starting out slowly and gradually increasing the work level. Similarly, use
several minutes of light exercise after the workout to bring your heart rate down
to near resting level.
The higher your fitness level, the longer you should maintain your heart rate in
the training zone (between 20 and 30 minutes). Beginners should always start
slowly, and gradually increase their sessions to 20 minutes or more.
How Often Should I Exercise?
Research indicates that aerobic sessions of 20 minutes or more should be done
at least 3 to 5 times a week to obtain significant cardiovascular benefits. Most
experts agree that sensible eating habits and regular aerobic exercise are the
keys to weight control and fitness. A recent study, which tracked several
subjects over a period of years, conclusively shows that exercise, not dieting, is
the key factor to successful long-term weight loss.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Troubleshooting
The climber requires little maintenance beyond periodic cleaning. Occassionally,
you will need to change the batteries when they wear down. Instructions for
these procedures are provided in this section. If you encounter problems with
the climber, refer to Troubleshooting Tips in this section for help.
Cleaning the Climber
CAUTION: Abrasive cleaners
or polishes will damage the
surface finish.
Clean the climber periodically with a mild solution of detergent and water or a
general household cleaner. Wipe the surface of the console with a moist cloth
and dry with a clean towel. Never pour liquids on the electronic console.
Changing the Batteries
The electronic console comes with two “AA” alkaline batteries installed. When
your console no longer shows a digital readout or the count becomes erratic,
you need to change the batteries.
Note: Occasionally, the batteries can become dislodged, so you need to
reposition the batteries in the drawer, but not necessarily replace them.
1. Locate the drawer on the side of the electronic console and press in lightly
to open it. Refer to Diagram 15 on page 13.
2. Use your fingers to slide the drawer out and expose the battery case.
Remove the old batteries and replace them with two new “AA” alkaline
batteries. The displays light up and the console beeps.
Note: Align the batteries to the proper polarity (+ and - indicators are inside
the battery case).
3. Close the battery drawer by pushing it gently into the electronic console.
4. Press START/STOP to activate the timer (TIME display). Note that you can
press RESET to “reset” the displays to zero.
Troubleshooting Tips
Check the chart below to see if your problem is listed. If the following informa-
tion does not solve a particular problem, call your authorized Precor dealer. See
Obtaining Service in this section for information
Problem
Solution
Electronics, no display
• Replace batteries. See instructions on the
previous page.
• Clean battery connections.
Electronics, no stroke count • Reed switch to magnet spacing is incorrect.
Electronic unit shuts down after 5 minutes—
see step 10 in the Assembly Instructions.
• Magnet placement incorrect.
• Pinched or severed cable.
Frame loose
Squeaks
• Recheck and tighten frame and base bolts.
• Lubricate the rope pulley mechanism.
• Lubricate resistance cylinder connectors.
• Check bolts for tightness.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Service
Do not attempt to service the climber yourself except for changing the batteries
or performing other maintenance tasks as described in this manual.
For further information about product operation or service, contact an autho-
rized Precor dealer (or a Precor Factory Authorized Service Company). To locate
the Precor dealer nearest you, call 1-800-4-PRECOR.
To help the customer service representative expedite your call, have your serial
number readily available. Use the model and serial numbers whenever you call
your Precor dealer or the customer service representative. The serial number on
the climber is located on the underside of the base.
Model number: 7_1_8_e_/_7_2_3_e Serial number: ___________________________
R
Precor Incorporated
P.O. Box 3004
Bothell, WA USA 98041-3004
Precor is a registered trademark of Precor Incorporated.
© 1995 Precor Incorporated, Rd.
P/N 31295-114
1/96
Specifications subject to change without notice.
1-800-4-PRECOR
NOTICE:
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor
aggressively seeks U.S. and foreign patents for both the mechanical construction and the visual aspects of
its product design. Any party contemplating the use of Precor's product designs is hereby forewarned that
Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor
will vigorously pursue all unauthorized appropriation of its proprietary rights.
Download from Www.Somanuals.com. All Manuals Search And Download.
|