Operating Instructions and Parts Manual
Powered Stock Feeder for Band Saws
Model PF-BS
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Part No. M-1790819
Ph.: 800-274-6848
Revision A 9/04
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service ..............................................................................................................................2
Warning...................................................................................................................................................4
Introduction..............................................................................................................................................6
Description ..............................................................................................................................................6
Specifications ..........................................................................................................................................6
Unpacking ...............................................................................................................................................7
Contents of the Shipping Container ......................................................................................................7
Mounting Hole Location........................................................................................................................8
Assembly and Installation ........................................................................................................................9
Mounting the Fence..............................................................................................................................9
Mounting the Feeder ..........................................................................................................................10
Grounding Instructions .......................................................................................................................11
Extension Cords.................................................................................................................................11
Adjustments...........................................................................................................................................12
Fence Movement ...............................................................................................................................12
Spring Tension...................................................................................................................................12
Arm Positioning..................................................................................................................................12
Rollers to Blade Distance ...................................................................................................................12
Changing Feed Rate ..........................................................................................................................13
Operating Controls.................................................................................................................................13
Operation...............................................................................................................................................13
Maintenance..........................................................................................................................................14
Lubrication .........................................................................................................................................14
Fence.................................................................................................................................................15
Troubleshooting.....................................................................................................................................15
Feed Rate/Belt Position .........................................................................................................................16
Replacement Parts ................................................................................................................................17
Parts List: Fence Assembly ...............................................................................................................18
Fence Assembly.................................................................................................................................19
Parts List: Feeder Assembly..............................................................................................................20
Feeder Assembly ...............................................................................................................................22
Electrical Connections ...........................................................................................................................23
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This stock feeder is designed and intended for use by properly trained and experienced personnel
only. If you are not familiar with the proper and safe operation of a stock feeder, do not use until
proper training and knowledge have been obtained.
5. Do not use this stock feeder for other than its intended use. If used for other purposes, WMH Tool
Group disclaims any real or implied warranty and holds itself harmless from any injury that may result
from that use.
6. Always wear approved safety glasses/face shields while using this stock feeder. Everyday
eyeglasses only have impact resistant lenses; they are not safety glasses.
7. Before operating this stock feeder, remove tie, rings, watches and other jewelry, and roll sleeves up
past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor
strips are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Make sure the stock feeder is firmly secured to the band saw before use.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
blahblahblah
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
23. Maintain a balanced stance at all times so that you do not fall or lean against moving parts. Do not
overreach or use excessive force to perform any machine operation.
24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
25. Use recommended accessories; improper accessories may be hazardous.
26. Maintain tools with care. Follow instructions for lubricating and changing accessories.
27. Turn off the stock feeder before cleaning. Use a brush or compressed air to remove chips or debris —
do not use your hands.
28. Do not stand on the machine. Serious injury could occur if the machine tips over.
29. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
30. Remove loose items and unnecessary work pieces from the area before starting the machine.
31. Check your stock for loose knots, nails or other aspects that may create a safety hazard or affect the
machine’s performance.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by Powermatic covering the safe operation and maintenance procedures for a
Model PF-BS Stock Feeder and Fence for Band Saws. This manual contains instructions on installation,
safety precautions, general operating procedures, maintenance instructions and parts breakdown. This
machine has been designed and constructed to provide years of trouble free operation if used in
accordance to instructions set forth in this manual. If there are any questions or comments, please
contact either your local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web
Description
The PF-BS Stock Feeder is designed for mounting to a band saw table 24” or larger in width. This heavy
duty Stock Feeder has a cast iron frame, and is ideal for plank splitting and under-bark trimming. The
serrated steel rollers provide a positive grip on the workpiece, and the tension against the workpiece can
be quickly and simply adjusted by turning a hex nut. The adjustable feed rate covers a range of eight
speeds.
Specifications
Model Number................................................................................................................................ PF-BS
Stock Number – 1 Ph, 230V......................................................................................................... 1790819
Stock Number – 3 Ph, 230V......................................................................................................... 1790820
Stock Number – 3 Ph, 460V......................................................................................................... 1790821
Fence:
Width (in.)..................................................................................................................................12-1/2
Height (in.).........................................................................................................................................8
Feeder:
Width (in.)..................................................................................................................................21-1/2
Height (in.).................................................................................................................................11-3/4
Length with Handle Installed (in.).....................................................................................................40
Column Diameter (in.).........................................................................................................................2.28
Rollers (Dia. x W)(in.).................................................................................................................. 7 x 1-1/2
Motor ................................................................................................................TEFC, 1/2HP, 1Ph or 3Ph
Rotation.................................................................................................................................Forward only
Number of Speeds...................................................................................................................................8
Speed Range (FPM)...........................................................................................10-17-20-27-33-45-57-93
Workpiece Thickness Allowed (in.)........................................................................................................7.1
Swing (deg.) ..........................................................................................................................................30
Fence Horizontal Movement (in.) .............................................................................................................4
Approximate Net Weight (lbs.) .............................................................................................................177
Approximate Shipping Weight (lbs.) .....................................................................................................211
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, WMH Tool Group reserves the right to change specifications at any time and
without prior notice, without incurring obligations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Container
Unpacking
1
1
1
6
6
1
1
Stock Feeder
Remove the plastic from around the Feeder and
Fence, and check for shipping damage. Report
any damage immediately to your distributor and
shipping agent. Do not discard any shipping
material until the Stock Feeder is assembled
and running properly.
Fence Assembly
Handle
Hex Cap Screws, M10 x 30
Lock Washers, M10
Owner's Manual
Warranty Card
Compare the contents of your container with the
following parts list to make sure all parts are
intact. Missing parts, if any, should be reported
to your distributor. Read the instruction manual
thoroughly for assembly, maintenance and
safety instructions.
Read and understand the entire contents of this manual before attempting set-up
or operation! Failure to comply may cause serious injury.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hole Location
NOTE: Dimensions are in inches, hole sizes are metric.
Figure 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly and Installation
Tools needed for assembly:
8.5mm drill bit
M10 x 1.5P tap
17mm wrench
Remove the clear plastic from around the Stock
Feeder and Fence Assembly.
Exposed metal surfaces have been given a
protective coating at the factory. This should be
removed with a soft cloth moistened with a good
commercial solvent, such as kerosene or
mineral spirits. Do not use acetone, gasoline, or
lacquer thinner for this purpose. Do not get
solvents near plastic or rubber parts, and do not
use an abrasive pad because it may scratch
metal surfaces.
The Stock Feeder should be mounted to a band
saw table in a well-lit area. Leave enough space
around the work area for loading and off-loading
stock and general maintenance.
The Stock Feeder and the
band saw to which you are mounting it
should both be disconnected from power
during installation.
Follow these steps to assemble and install the
Stock Feeder and Fence:
Use the diagram in Figure 1 (page 8) to identify
the proper location for marking the hole patterns
on the band saw table. Do not drill and tap the
holes yet, only mark them.
Mounting the Fence
Figure 2
1. The fence must be parallel with the blade
for accurate cuts as well as for safety. To
achieve this, mark the location of the near
hole for the Fence based on the dimensions
in Figure 1, page 8. Drill and tap the near
hole then place the fence over the hole
pattern. Insert an M10 x 30 hex cap screw
with lock washer into the near hole, as
shown in Figure 2. With a 17mm wrench,
make the screw snug. Do not tighten
completely.
2. Loosen the handle (A, Figure 3) and rotate
the knob (B, Figure 3) until the fence is right
up to the blade; that is, the scale on the
fence should be at “0”.
Figure 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tighten the handle (A, Figure 3). If
necessary, move the Fence slightly to bring
it parallel with the blade.
4. When satisfied, mark the location of the
second hole using the hole in the Fence
base as your template.
5. Remove the Fence from the table, and drill
and tap the second hole.
6. Place the Fence over the hole pattern again,
and secure the Fence to the table with two
M10 x 30 hex cap screws and two M10 lock
washers. Tighten firmly.
Figure 4
Mounting the Feeder
1. Screw the handle (Figure 4) all the way into
the threaded hole of the Stock Feeder.
NOTE: If the mounting surface is narrow, a
bracket (not provided) must be attached to
support the Stock Feeder. Figure 5 shows an
example.
The Stock Feeder is heavy.
Use a hoist during installation procedures.
Failure to comply may cause injury!
Figure 5
2. Figure 6 shows the proper method of lifting
the Stock Feeder with a hoist. Place one
end of the strap or rope around the motor
mount and the other end around the handle,
as shown.
3. Lift the Stock Feeder carefully into place
over the hole pattern previously marked on
the band saw table, and verify that the hole
pattern lines up correctly with the holes in
the Stock Feeder base.
4. Remove the Stock Feeder, and drill and tap
the four holes.
Figure 6
5. Secure the Stock Feeder to the table with
four M10 x 30 hex cap screws and four M10
lock washers. See Figure 7.
6. It is important that the serrated rollers of the
Stock Feeder are properly positioned in
reference to the blade. Figure 8 shows how
the center of the rollers should be aligned
with the front tips of the blade teeth. The
gearbox top cover is aligned with the rollers,
so you can use the top cover’s center for
making this alignment. See Figure 8.
Figure 7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Electrical connections must
qualified electrician in
be made by
a
compliance with all relevant codes. This
machine must be properly grounded to help
prevent electrical shock and possible fatal
injury.
As received from the factory, the PF-BS Stock
Feeder will run on either 230 volt or 460 volt,
depending upon your particular model. Make
sure the voltage of your power supply matches
the specifications on the motor plate of the
machine.
Figure 8
You may either connect an appropriate UL/CSA
listed plug or “hard-wire” the machine directly to
a control panel. If hard-wired to a panel, make
sure a disconnect is available for the operator.
The Stock Feeder must comply with all local and
national codes after being wired. If it is to be
hard-wired, make sure the fuses have been
removed or the breakers have been tripped in
the circuit to which the Stock Feeder will be
connected. Place a warning placard on the fuse
holder or circuit breaker to prevent it being
turned on while the machine is being wired.
Refer to “Electrical Connections” on page 23 for
connecting the motor leads.
This machine must be grounded. In the event of
a malfunction or breakdown, grounding provides
a path of least resistance for electric current, to
reduce the risk of electric shock to the operator.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Recommended Gauges (AWG) of Extension Cords
Extension Cord Length *
25
50
75
100 150 200
Amps
feet feet feet feet feet feet
Repair or replace a damaged or worn cord
immediately.
< 5
16
16
14
12
10
10
16
16
14
12
10
NR
16
14
12
10
10
NR
14
12
12
10
12
5 to 8
NR
NR
NR
NR
NR
Extension Cords
8 to 12
12 to 15
15 to 20
21 to 30
10
NR
NR
NR
NR
If an extension cord is necessary make sure the
cord rating is suitable for the amperage listed on
the machine's motor plate. An undersize cord
will cause a drop in line voltage resulting in loss
of power and overheating.
10
NR
NR
The chart in Figure 9 shows the correct size
cord to use based on cord length and motor
plate amp rating. If in doubt, use the next
heavier gauge. The smaller the gauge number
the heavier the cord.
*based on limiting the line voltage drop to 5V at 150% of the
rated amperes.
NR: Not Recommended.
Figure 9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Fence Movement
To move the fence toward or away from the saw
blade, loosen the lock handle (A, Figure 10) and
rotate the knob (B, Figure 10).
A millimeter scale is inscribed on the edge of the
rack (C, Figure 10).
After adjustment, re-tighten lock handle (A,
Figure 10).
Spring Tension
Figure 10
The amount of tension directed against the
workpiece is controlled by the spring, and is
adjustable. Regulate the tension on the spring
by turning the hex nut, shown in Figure 11. Turn
the hex nut clockwise to increase tension,
counterclockwise to decrease tension.
Arm Positioning
The arm of the Stock Feeder can be pulled
away from the blade and secured there by
pushing up the stop rod (Figure 11) into the hole
in the bracket. NOTE: Make sure the stop rod is
pushed up as far as it will go into the hole.
To release the arm, pull back slightly on the
handle of the Stock Feeder, and pull the stop
rod downward out of the hole. Carefully allow
the arm to swing back toward the blade.
Figure 11
The arm will swing back
toward the blade with force when the spring
is tensioned. Guide the arm back without
letting it hit the saw blade.
Rollers to Blade Distance
The distance of the serrated rollers to the band
saw blade can be fine-adjusted with the hex
nuts (Figure 12).
1. Loosen outer hex nut (B, Figure 12).
2. Pull back on the Stock Feeder arm, and
turn the inner hex nut (A, Figure 12) as
needed.
3. Lock the setting by tightening the outer hex
nut (B, Figure 12) up against the inner hex
nut (A, Figure 12).
Figure 12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Feed Rate
1. Loosen the two hex nuts (one is shown in
Figure 13) that hold the motor to the motor
mount. Use a 12mm wrench. Do not remove
the hex nuts, loosen them only enough so
that the motor can be pivoted.
2. Pivot the motor counterclockwise, as shown
in Figure 13. This will produce slack in the
belt.
3. Open the pulley cover door (Figure 14) by
unscrewing the knob.
4. Roll the belt into the appropriate pulley
groove for the desired feed rate. A label is
affixed to the inside of the door (Figure 14)
that shows the configurations for belt
position/feed rate in both feet per minute
and meters per minute. This feed rate chart
is also reproduced on page 16.
Figure 13
5. When the belt has been changed, close the
pulley door and tighten the knob.
6. Rotate the motor clockwise to tension the
belt. Proper tension is achieved when the
belt can be deflected approximately 3 to
5mm with slight finger pressure.
7. Tighten the two hex nuts (Figure 13).
Figure 14
Operating Controls
The control switch (Figure 15) turns on the
Stock Feeder motor, and also helps determine
feed rate in conjunction with the pulley position.
“Fast” and “Slow” are identified by the universal
symbols of hare and tortoise.
Operation
IMPORTANT: Before attempting operation of
this stock feeder in conjunction with a band saw,
you should be thoroughly familiar with the
operating and safety instructions that were
included with the band saw.
Figure 15
Keep hands away from
rollers, spring, and other pinch points of the
Stock Feeder during operation. Failure to
comply may cause injury.
The following are basic steps for operating the
Stock Feeder.
1. Make sure the band saw is working properly
and that the blade is sharp; and that all
guards are properly installed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Set the desired rate of feed on the Stock
Feeder by moving the belt to the proper
pulley grooves. Proper rate of feed will
depend upon the hardness and thickness of
the workpiece, and is best learned through
experience.
3. Set the Fence so that the dimension on the
scale (C, Figure 10) matches the desired
thickness of the workpiece. Secure the
Fence in position with the locking handle.
4. Turn on the band saw and the Stock
Feeder, and carefully feed the workpiece
through the blade.
NOTE: If a jam should occur while feeding, turn
off the band saw and the Stock Feeder, pivot the
Stock Feeder out of the way, and remove the
workpiece. Return the Stock Feeder to position
and begin the cut over again.
Maintenance
Before performing any
maintenance
on
the
Stock
Feeder,
disconnect it from the electrical supply by
pulling out the plug or switching off the
breaker. Also make sure the band saw is
disconnected from power. Failure to comply
may cause serious injury.
If the power cord is worn, cut, or damaged in
any way, have it replaced immediately.
Frequently blow out dust and chips from the
Stock Feeder with compressed air.
Lubrication
Gearbox
The Stock Feeder is shipped with oil installed in
the gearbox. Check the oil about every 3 months
and top off as necessary with a good quality
general-purpose gear oil.
Figure 16
To add oil to the gearbox:
1. Loosen and remove the oil cap (Figure 16).
2. Fill with oil up to level, by observing the level
indicator (Figure 17).
3. Re-install the oil cap.
Figure 17
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Arm Axis
Keep the axis of the arm lubricated with a good
quality general purpose grease, inserted through
the grease fitting (Figure 18).
Figure 18
Fence
At least once a week, place a light coat of oil on
the sliding column of the fence. Also place a
drop of oil on each roller pin. See Figure 19.
Figure 19
Troubleshooting
Trouble
Probable Cause
Remedy
Check power connections.
Not connected to power source.
Feeder will not start.
Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker.
Cord damaged.
Replace cord.
Belt not situated in correct pulley
grooves to achieve desired speed.
Install belt in correct pulley grooves.
[page 13]
Feed rate is not
sufficient; or machine
has low power.
Replace with adequate size and
length cord. [page 11]
Extension cord too light or too long.
Low current from electrical supply.
Contact a qualified electrician.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed Rate/Belt Position
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848 between 7:00 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model
Number and Serial Number of your machine available when you call will allow us to serve you quickly and
accurately.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Fence Assembly
Index No. Part No.
Description
Size
Qty
1...............PFBS-101 ............... Roller Fence...................................................... ...................................1
2...............PFBS-102 ............... Column.............................................................. ...................................1
3...............PFBS-103 ............... Rack ................................................................. ...................................1
4...............TS-1502031 ............ Socket Head Cap Screw.................................... M5x12 ........................3
5...............TS-2361081 ............ Lock Washer...................................................... M8..............................4
6...............TS-1490051 ............ Hex Cap Screw.................................................. M8x30 ........................4
7...............PFBS-107 ............... Roller Mounting Strip ......................................... ...................................2
8...............TS-1502081 ............ Socket Head Cap Screw.................................... M5x35 ........................8
9...............PFBS-109 ............... Fence Roller...................................................... .................................15
10.............PFBS-110 ............... Mounting Base................................................... ...................................1
11.............TS-2361101 ............ Lock Washer...................................................... M10............................2
12.............TS-1491041 ............ Hex Cap Screw.................................................. M10x30 ......................2
13.............PFBS-113 ............... Lock Handle ...................................................... ...................................1
14.............TS-0680061 ............ Flat Washer....................................................... 1/2".............................1
15.............PFBS-115 ............... Stud .................................................................. ...................................1
16.............PFBS-116 ............... Pinion................................................................ ...................................1
17.............PFBS-117 ............... Knob.................................................................. ...................................1
18.............PFBS-118 ............... Pin..................................................................... 6x36 ...........................1
19.............TS-1524061 ............ Socket Set Screw .............................................. M8x25 ........................1
20.............TS-2361081 ............ Lock Washer...................................................... M8..............................1
21.............TS-1540061 ............ Hex Nut ............................................................. M8..............................1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Assembly
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Feeder Assembly
Index No. Part No.
Description
Size
Qty
1...............BB-6202ZZ.............. Ball Bearing....................................................... 6202ZZ.......................1
2...............BB-6204Z................ Ball Bearing....................................................... 6204Z.........................1
3...............BB-6205Z................ Ball Bearing....................................................... 6205Z.........................1
4...............BB-6206Z................ Ball Bearing....................................................... 6206Z.........................1
5...............PFBS-205 ............... Gearbox Top Cover ........................................... ...................................1
6...............TS-1503051 ............ Socket Head Cap Screw.................................... M6x20 ........................4
7...............TS-1551041 ............ Lock Washer...................................................... M6..............................4
8...............PFBS-208 ............... Oil Cap .............................................................. ...................................1
9...............PFBS-209 ............... "O" Ring............................................................. ...................................1
10.............PFBS-210 ............... Worm Gear........................................................ ...................................1
11.............PFBS-211 ............... Gear Shaft......................................................... ...................................1
12.............PFBS-212 ............... Key.................................................................... 8x7x20........................1
13.............PFBS-213 ............... Key.................................................................... 8x7x90........................1
14.............TS-1550111 ............ Flat Washer....................................................... M20............................1
15.............TS-2310201 ............ Hex Nut ............................................................. M20............................1
16.............PFBS-216 ............... Reduction Gearbox............................................ ...................................1
17.............PFBS-217 ............... Level Indicator................................................... ...................................1
18.............PFBS-218 ............... Grease Fitting.................................................... ...................................1
19.............PFBS-219 ............... Handle............................................................... ...................................1
20.............PFBS-220 ............... Worm Gear Cover.............................................. ...................................1
21.............TS-1551041 ............ Lock Washer...................................................... M6..............................3
22.............TS-1503041 ............ Socket Head Cap Screw.................................... M6x16 ........................3
23.............PFBS-223 ............... Gearbox Bottom Cover ...................................... ...................................1
24.............PFBS-224 ............... Retaining Ring................................................... ...................................1
25.............TS-1551041 ............ Lock Washer...................................................... M6..............................4
26.............TS-1503051 ............ Socket Head Cap Screw.................................... M6x20 ........................4
27.............PFBS-227 ............... Roller Cover ...................................................... ...................................1
28.............PFBS-228 ............... Mounting Base................................................... ...................................1
29.............TS-1491041 ............ Hex Cap Screw.................................................. M10x30 ......................4
30.............TS-2361101 ............ Lock Washer...................................................... M10............................4
31.............PFBS-231 ............... Stop Rod ........................................................... ...................................1
32.............PFBS-232 ............... "E" Clip.............................................................. ...................................1
33.............PFBS-233 ............... Stop Plate.......................................................... ...................................1
34.............TS-1491031 ............ Hex Cap Screw ................................................. M10x25 ......................4
35.............TS-2361101 ............ Lock Washer...................................................... M10............................4
36.............PFBS-236 ............... Worm................................................................. ...................................1
37.............PFBS-237 ............... Key.................................................................... 5x5x25........................1
38.............PFBS-238 ............... Worm Gear Cap................................................. ...................................1
39.............PFBS-239 ............... Compensating Collar ........................................ ...................................1
40.............PFBS-240 ............... Oil Seal.............................................................. ...................................1
41.............TS-1551041 ............ Lock Washer...................................................... M6..............................4
42.............TS-1503071 ............ Socket Head Cap Screw.................................... M6x30 ........................4
43.............PFBS-243 ............... Pulley Housing................................................... ...................................1
44.............PFBS-244 ............... Worm Gear Pulley ............................................. ...................................1
45.............TS-1550041 ............ Flat Washer....................................................... M6..............................1
46.............TS-1482031 ............ Hex Cap Screw.................................................. M6x16 ........................1
47.............PFBS-247 ............... Motor Pulley ...................................................... ...................................1
48.............TS-1550041 ............ Flat Washer....................................................... M6..............................1
49.............TS-1503041 ............ Socket Head Cap Screw.................................... M6x16 ........................1
50.............PFBS-250 ............... Belt.................................................................... M-18...........................1
51.............PFBS-251 ............... Pulley Housing Cover ........................................ ...................................1
52.............TS-1551041 ............ Lock Washer...................................................... M6..............................2
53.............TS-1503041 ............ Socket Head Cap Screw.................................... M6x16 ........................3
54.............PFBS-254 ............... Motor................................................................. 1/2 HP, 230V, 3Ph......1
.................PFBS-254A............. Motor................................................................. 1/2 HP, 460V, 3Ph......1
.................PFBS-254B............. Motor................................................................. 1/2HP, 230V, 1Ph.......1
.................PFBS-254CA .......... Capacitor (only for 1 phase) – Not shown........... 350V 25uf...................1
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Index No. Part No.
Description
Size
Qty
55.............TS-1550061 ............ Flat Washer....................................................... M8..............................2
56.............TS-1490061 ............ Hex Cap Screw.................................................. M8x35 ........................1
57.............PFBS-257 ............... Lock Screw........................................................ ...................................1
58.............TS-2361081 ............ Lock Washer...................................................... M8..............................2
59.............TS-1540061 ............ Hex Nut ............................................................. M8..............................2
60.............PFBS-260 ............... Key.................................................................... 5x5x30........................1
61.............PFBS-261 ............... Pulley Housing Door.......................................... ...................................1
62.............PFBS-262 ............... Hinge................................................................. ...................................1
63.............TS-2171012 ............ Machine Screw, Pan Head................................. M4x6 ..........................4
64.............TS-1540021 ............ Hex Nut ............................................................. M4..............................4
65.............PFBS-265 ............... Knob.................................................................. ...................................1
66.............PFBS-266 ............... Spring Hinge...................................................... ...................................1
67.............TS-2361081 ............ Lock Washer...................................................... M8..............................1
68.............TS-1490031 ............ Hex Head Bolt ................................................... M8x20 ........................1
69.............TS-2361081 ............ Lock Washer...................................................... M8..............................3
70.............TS-1490041 ............ Hex Cap Screw ................................................. M8x25 ........................3
71.............TS-1490051 ............ Hex Cap Screw ................................................. M8x30 ........................1
72.............PFBS-272 ............... Spring Adjusting Rod......................................... ...................................1
73.............TS-155009 .............. Flat Washer....................................................... M14............................1
74.............PFBS-274 ............... Bumper Ring...................................................... ...................................1
75.............TS-154009 .............. Hex Nut ............................................................. M14............................3
76.............PFBS-276 ............... Spring Guide Set (2 Pieces/Set)......................... ...................................1
77.............PFBS-277 ............... Spring................................................................ ...................................1
78.............PFBS-278 ............... Switch Box Kit.................................................... ...................................1
79.............PFBS-279 ............... Switch Kit........................................................... ...................................1
80.............PFBS-280 ............... Spacer............................................................... ...................................1
81.............PFBS-281 ............... Bushing ............................................................. ...................................1
82.............PFBS-282 ............... Steel Roller........................................................ ..................................2
83.............PFBS-283 ............... Oil Seal.............................................................. 35...............................1
84.............PFBS-284 ............... Oil Seal.............................................................. 115.............................2
85.............PFBS-285 ............... Oil Seal.............................................................. 20x35x7......................1
86.............PFBS-286 ............... Label, Feed Rate (not shown) ............................ ...................................1
87.............PFBS-287 ............... Warning Label (not shown) ................................ ...................................1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Feeder Assembly
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH Tool Group
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|