R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
GHT 220
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, ON L5R 4C2
Copyright E2003 Electrolux Home Products, Inc.
530163751
10/9/03
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
Blades can throw objects violently.
D You can be blinded or injured.
D Wear safety glasses.
Safety
Glasses
Boots
WARNING:
Hazard zone for thrown objects
D Blades can throw objects violently.
D Others can be blinded or injured.
D Keep people and animals 30 feet
(10 meters) away.
30 ft.
(10 m)
Blades move Allow blades to stop
momentarily before removing
he them from the cut.
is
WARNING:
Blades move momentarily after the
trigger is released.
D The blades can seriously cut you or
others.
d.
D Allow blades to stop before
removing them from the cut.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equippedwithaspark arrestingscreen. Ifyou
operateinalocale wheresuch regulationsex-
ist, you arelegally responsible formaintaining
the operatingcondition of theseparts. Failure
to do so is a violation of the law. Refer to the
SERVICE section for maintenance of the
muffler and spark arresting screen.
D Store the unit so the cutting blade cannot
accidentally cause injury.
D Store in a dry area out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swelling. Prolonged use in cold
weatherhas beenlinked toblood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti vibration system
does not guarantee the avoidance of these
problems. Users who operatepower tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
ASSEMBLY
NOTE:It is normal for thefuel filter to rattle in
the empty fuel tank.
ASSEMBLY
Your hedgetrimmer is fully assembled; noas-
sembly is required.
-- 3 --
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR HEDGE TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the vari-
ous controls and adjustments. Save this manual for future reference.
Muffler
ON/OFF
Switch
Spark Plug
Throttle Lock
Hand Guard
Throttle
Lock--out
Throttle
Trigger
Primer Bulb
Fuel Mix Fill Cap
Choke Lever
ON/OFF SWITCH
PRIMER BULB
The ON/OFF SWITCH is used to stop the en-
gine. To stop engine, move switch to OFF.
ThePRIMER BULBremoves air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original position.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving choke lever to the desired position. See
STARTING YOUR ENGINE for complete start-
ing information.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. Squeeze the trigger for full speed opera-
tion; release it for idle speed.
IMPORTANT
WARNING: Muffler is very hot during
and after use. Do not touch the muffler or al-
low combustible material such as dry grass or
fuel to do so.
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
empty the fuel system before storage for 30
days or longer. Drain the gas tank, start the en-
gine and let it run until the fuel lines and carbure-
tor are empty. Use fresh fuel next season. Nev-
er use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understandthe safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
OPERATING INSTRUCTIONS
IMPORTANT POINTS
S Use the minimum throttle speed necessary
to effectively cut hedges for optimal hedge
trimmer performance.
S Never attempt to use this hedge trimmer to
cut hedges that have any branches with a
diameter larger than 7/16" (1 cm).
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. A 40:1
ratio is obtained by mixing 3.2 ounces (95 ml)
of oil with 1 gallon (4 liters) of unleaded gaso-
line. DO NOT USE automotive oil or boat oil.
These oils will cause engine damage. When
mixing fuel, follow instructions printed on oil
container. Once oil is added to gasoline,
shake container momentarily to assure that
thefuel is thoroughly mixed. Always readand
follow the safety rules listed under HANDLE
FUEL WITH CAUTION.
OPERATING POSITION
Hearing
Protection
tion
-- 4 --
Download from Www.Somanuals.com. All Manuals Search And Download.
Primer Bulb
STOPPING YOUR ENGINE
D To stop the engine, move the ON/OFF
switch to the OFF position.
Choke
Lever
STARTING YOUR ENGINE
D
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
Hold the unit on the ground in the starting
position as shown. Support unit so the
blade is off of the ground and away from
trees, bushes, onlookers, etc.
5. Pull starter rope handle sharply until en-
gine sounds as if it is trying to run, but do
not pull rope more than 6 times.
6. Move the choke lever to the HALF
CHOKE position.
7. Pull starter rope sharply until the engine
runs, but no more than 6 pulls.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
check to make sure the ON/OFF switch is
in the ON position. Move the choke lever
to the FULL CHOKE position and press
the primer bulb 6 times; pull the starter
rope 2 more times. Move the choke lever
to the HALF CHOKE position and pull the
starter rope until the engine runs, but no
more than 6 more pulls. If the engine still
doesn’t start, it is probably flooded. Pro-
ceed to STARTING A FLOODED EN-
GINE.
8. Once the engine starts, allow the engine to
run 10 seconds, then move the choke lever
totheOFF CHOKE position. Allow the unit to
run for 30 more seconds at the OFF CHOKE
position before squeezing and releasing the
throttle trigger to release the throttle lock.
NOTE:If enginedies withthe chokelever
in the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
and pull the rope until the engine runs, but
no more than 6 pulls.
Throttle Lock
Throttle
Lock-out
Throttle
Trigger
1. Move the ON/OFF switch to the ON posi-
tion.
2. Engage the throttle lock as follows:
D press the throttle lock--out;
D squeeze and hold throttle trigger;
D press and hold throttle lock, then
D release the throttle trigger
NOTE: Keep the throttle lock engaged until
the engine starts.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENGINE.
NOTE: Keep the throttle lock engaged until
the engine starts.
ON
OFF
Switch
5. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
6. Allow the engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position.
7. Releasethethrottlelock by squeezingand
releasing the trigger.
NOTE: If engine has not started, pull starter
rope5morepulls. If enginestill doesnot run,it
is probably flooded. Proceedto STARTING A
FLOODED ENGINE.
3. Slowly press the primer bulb 6 times.
4. Move the chokelever tothe FULLCHOKE
position.
-- 5 --
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
theON/OFF switch in the ONposition andthe
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then,
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn’t start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debris from falling into thecarburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter; squeeze
filter to distribute oil.
6. Replace parts.
SERVICE
WARNING: Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
GENERAL RECOMMENDATIONS
Thewarrantyonthis unit doesnot cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
NOTE: THE SPARK ARRESTING SCREEN
ON THIS UNIT IS NOT SERVICEABLE.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice.
After 50 hours of use, we recommend that
your muffler be replaced by an authorized
service dealer.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The blade
will be moving during most of this procedure.
Wear your protective equipment andobserve
all safety precautions. When making adjust-
ments, use a screwdriver short enough to
keep your hands behind the handguard and
away from the blade. After making adjust-
ments, the blade mustnot moveat idle speed.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to the
OFF position. Make sure engine stops; then
restart engine and continue.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
S The blade moves at idle.
INSPECT AND CLEAN UNIT AND
LABELS
S Before and after each use, inspect com-
plete unit for loose or damaged parts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
Keep others away when making idle speed
adjustments. Make adjustments with the unit
resting on a level surface free of debris that
can be caught in the hedge trimmer blade.
Serious injury to the operator and others can
occur if the carburetor is not properly ad-
justed. Keep all parts of your body away from
the blade and muffler.
CLEAN AIR FILTER
Idle Speed Adjustment
Air Filter
Cover
Allow engineto idle. Adjust speed until engine
runswithoutblademoving(idle toofast) oren-
gine stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
creaseenginespeedif enginestalls ordies.
S Turn idle speed screw counterclockwise to
decrease engine speed if the blade moves
at idle.
WARNING: Recheck the idle speed
after each adjustment. The blade must not
move at idle speed to avoid serious injury to
the operator or others.
Air Filter
Screw
-- 6 --
Download from Www.Somanuals.com. All Manuals Search And Download.
Idle Speed Screw
SEASONAL STORAGE
Prepareunit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit.
S Store in a clean dry area.
S Clean all parts and check for damage.
Have damaged parts repaired or replaced
by an authorized service dealer.
S Keep all nuts, bolts, and screws tight.
S Lightly oil external metal surfaces, includ-
ing the blade.
To oil the blade, do the following:
S Stop the engine and allow blade to come to
a complete stop.
S Ensure ON/OFF switch is in the OFF posi-
tion.
S Disconnect the spark plug wire.
S Apply a light machine oil along the edge of
the top strap as shown.
If you requirefurtherassistance or areunsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
OIL
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
Top Strap
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual,see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine. Fuel stabilizer is an ac-
ceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabi-
lizer to gasoline in fuel tank or fuel storage con-
tainer. Follow the mix instructions found on sta-
bilizer container. Run engine at least 5 minutes
after adding stabilizer.
REPLACE FUEL FILTER
Toreplacefuel filter, drainunit by runningit dry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank andremove
it fromthe fuel line. Install new fuelfilter onfuel
line; reinstall parts.
ENGINE
Fuel Filter
S Remove spark plug and pour 1 teaspoonof
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range (see RE-
PLACE SPARK PLUG section).
S Clean air filter.
Fuel Line
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having thepropergasolineto
oil ratio.
STORAGE
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts torust.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
NEED ASSISTANCE?
NEED ASSISTANCE?
Call 1-800-554-6723 for assistance.
NEED SERVICE PARTS?
Contact your authorized service dealer.
S Store unit and fuel well out of the reach of
children.
-- 7 --
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unitand disconnectspark plugbeforeperformingall ofthe
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. ON/OFF switch in the
OFF position.
2. Engine flooded.
1. Move ON/OFF switch to the ON
position.
2. See “Starting a Flooded Engine”
in Operation Section.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Compression low.
6. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs
hot.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
-- 8 --
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
cover predelivery setup or normal adjustments
warrants to the original purchaser that each new
Weed EaterR brand gasoline tool or attach-
ment is free from defects in material and work-
manship and agrees to repair or replace under
this warranty any defective gasoline product or
attachment as follows from the original date of
purchase.
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune--ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
The policy of ELECTROLUX HOME PROD-
UCTS, INC., is to continuously improve its prod-
ucts.
Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
U.S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
ProtectionAgency, EnvironmentCanadaand
ELECTROLUX HOME PRODUCTS, INC.,
are pleased to explain the emissions control
system warranty on your year 2002--2004
deny warrantysolely forthe lack of receipts or
for your failure to ensure the performance of
all scheduled maintenance. As thesmall off--
road engine owner, you should be aware that
ELECTROLUX HOME PRODUCTS, INC.,
may deny you warranty coverage if your
small off--road engine or a part of it has failed
due to abuse, neglect, improper mainte-
nance, unapproved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsi-
ble for presenting your small off--road engine
to an ELECTROLUX HOME PRODUCTS,
INC., authorized repair center as soon as a
problem exists. Warranty repairs should be
completed in a reasonable amount of time,
not to exceed 30 days. If you have any ques-
tions regarding your warranty rights and re-
sponsibilities, you should contact your near-
est authorized service center or call ELEC-
TROLUX HOME PRODUCTS, INC., at
small off--road engine.
ELECTROLUX
HOME PRODUCTS, INC., must warrant the
emission control system on your small off--
road engine for the periods of time listed be-
low provided there has been no abuse, ne-
glect, or improper maintenance of your small
off--road engine. Your emission control sys-
temincludes partssuch as the carburetorand
the ignition system. Where a warrantable
condition exists, ELECTROLUX HOME
PRODUCTS, INC., will repair your small off--
road engine at no cost to you. Expenses cov-
ered under warranty include diagnosis, parts
and labor. MANUFACTURER’S WARRAN-
TY COVERAGE: If any emissions related
part on your engine (as listed under Emis-
sions Control Warranty Parts List) is defec-
tive or a defect in the materials or workman-
ship of the engine causes the failure of such
an emission related part, the part will be re-
paired or replaced by ELECTROLUX HOME
PRODUCTS, INC. OWNER’S WARRANTY
RESPONSIBILITIES: As the small off--road
engineowner, youareresponsiblefor theper-
formance of the required maintenance listed
in your instruction manual. ELECTROLUX
HOME PRODUCTS,INC., recommends that
you retain all receipts covering maintenance
on your small off--road engine, but ELEC-
TROLUX HOME PRODUCTS, INC., cannot
1--800--554--6723.
WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years fromthe initial dateofpurchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved ELEC-
TROLUX HOME PRODUCTS, INC., servic-
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call ELECTROLUX HOME
-- 9 --
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCTS, INC., at 1--800--554--6723.
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled
only for regular inspection to the effect of “re-
pair or replace as necessary” shall be war-
ranted for 2 years. Any warranted part which
is scheduled for replacement as required
maintenanceshall bewarrantedfor theperiod
of time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved ELECTROLUX
HOME PRODUCTS, INC., servicing center.
CONSEQUENTIAL DAMAGES: ELEC-
TROLUX HOME PRODUCTS, INC., may be
liable for damages to other engine compo-
nents caused by the failure of a warranted
part still under warranty. WHAT IS NOT
COVERED: All failures caused by abuse, ne-
glect, or improper maintenance are not cov-
ered. ADD-ON OR MODIFIED PARTS: The
use of add--on or modified parts can be
grounds for disallowing a warranty claim.
ELECTROLUXHOME PRODUCTS, INC., is
not liable to cover failures of warranted parts
caused by the use of add--on or modified
parts. HOW TO FILE A CLAIM: If you have
any questions regarding your warranty rights
and responsibilities, you should contact your
nearest authorized service center or call
ELECTROLUXHOMEPRODUCTS, INC.,at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all ELECTROLUX
HOME PRODUCTS, INC., service centers.
Call 1--800--554--6723. MAINTENANCE,
REPLACEMENT AND REPAIR OF EMIS-
SION RELATED PARTS: Any ELECTRO-
LUX HOME PRODUCTS, INC., approvedre-
placement part used in the performance of
any warranty maintenance or repair on emis-
sion related parts will be provided without
charge to the owner if the part is under war-
ranty. EMISSION CONTROL WARRANTY
PARTS LIST: Carburetor, Ignition System:
Spark Plug (covered up to maintenance
schedule), Ignition Module. MAINTENANCE
STATEMENT: The owner is responsible for
the performance of all required maintenance
as defined in the instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 1 0 --
Download from Www.Somanuals.com. All Manuals Search And Download.
|