R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
NOT DESIGNED FOR USE WITH
ELECTRIC POWERHEADS
NO ESTA DISEÑADO PARA EL USO CON
PPB4000C
CABEZAS DE MOTOR ELÉCTRICO
NON CONÇU POUR L’USAGE AVEC
BLOC-MOTEURS ÉLECTRIQUES
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury. Refer
to your original manual for additional Warnings and Operating
Instructions.
PELIGRO:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves. Refiera a su manual original para las Instruc-
ciones de Funcioniamiento y las Advertencias adicionales.
DANGER:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves. Référez--vous à
votre manuel original pour des Avertissements et des Instruc-
tions d’Utilisation additionnels.
Poulan PRO
7349 Statesville Road
Charlotte, NC 28269
545212832 Rev. 3 6/15/10 BRW
Download from Www.Somanuals.com. All Manuals Search And Download.
IDENTIFICATION OF SAFETY SYMBOLS
Blade/trimmer line can throw objects
violently. You can be blinded or injured.
Always wear hearing protection and
safety glasses marked Z87. Always
wear head protection, heavy, long pants,
long sleeves, boots and gloves.
Hazard zone for thrown objects.
D Blade/trimmer line can throw objects violently.
D You and others can be blinded/injured.
D Keep children, bystanders, and animals 50 feet (15
meters) away.
SAFETY RULES
S Being fully covered also helps protect you
from debris and pieces of toxic plants
WARNING: When using gardening ap-
thrown by spinning line/blade.
pliances, basic safety precautions should al-
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
Failure to do so can result in serious injury.
S Stay alert. Do not operate unit when you are
tired, ill, upset or under influence of alcohol,
drugs, or medication. Watch what you are
doing; use common sense.
S Wear hearing protection.
DANGER: This power tool can be dan-
gerous! This unit can cause serious injury in-
cluding amputation or blindness to the opera-
tor and others. The warnings and safety
instructions in this manual must be followed to
provide reasonable safety and efficiency in
using the unit. The operator is responsible for
following the warnings and instructions in this
manual and on the unit. Read the entire in-
struction manual before assembling andusing
the unit! Restrict the use of this unit to persons
who read, understand, and follow the warn-
ings and instructions in this manual and on the
unit. Never allow children to operate this unit.
S Never start or run the engine inside a closed
room or building. Breathing exhaust fumes
can kill.
S Keep handles free of oil and fuel.
S Always use the handlebar and a properly
adjusted shoulder strap when using brush-
cutter attachment (see ASSEMBLY).
UNIT/MAINTENANCE SAFETY
WARNING: Disconnect powerhead
spark plug before performing maintenance.
S Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep unit in good
working condition.
S Throw away blades that are bent, warped,
cracked, broken, or damaged in any other
way. Replace trimmer head parts that are
cracked, chipped, broken, or damaged in
any other way before using the unit.
S Maintain the unit according to recommended
procedures. Keep the blade sharp. Never use
flailing devices, wire, rope, string, etc.
S Use only specified trimmer head or blade;
make sure it is properly installed and se-
curely fastened.
INSTRUCTION
MANUAL
SAFETY INFORMATION
ON THE UNIT
OPERATOR SAFETY
S Dress properly. Always wear safety glasses
or similar eye protection when operating, or
performing maintenance on your unit (safe-
ty glasses are available). Eye protection
should be marked Z87.
S Always wear face or dust mask if operation
is dusty.
S Use only 0.080″ (2 mm) diameter Poulan
PRO brand line. Never use wire, rope,
string, etc.
S Always wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
S Never start engine with clutch shroud re-
moved. The clutch can fly off and cause se-
rious injury.
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of spin-
ning line/blade.
S Be sure blade stops turning when engine
idles.
S Secure hair above shoulder length. Secure or
remove loose clothing and jewelry or clothing
with loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
S Make carburetor adjustments with the lower
end supported to prevent the blade from
3
Download from Www.Somanuals.com. All Manuals Search And Download.
contacting any object. Hold the unit by hand;
do not use the shoulder strap for support.
S Keep others away when making carburetor
adjustments.
S Cut from your left to your right. Cutting on
the right side of the shield will throw debris
away from the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
S Use only recommended Poulan PRO ac-
cessories and replacement parts.
TRANSPORTING AND STORAGE
S Stop the powerhead engine before carrying
unit.
S Have all maintenance and service not ex-
plained in this manual performed by an au-
thorized service dealer.
S Keep muffler away from your body.
S Allow engine to cool and secure unit before
storing or transporting it in a vehicle.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit or while using the unit.
S Avoid spilling fuel or oil. Wipe up all fuel
spills before starting engine.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Store unit so the blade cannot accidentally
cause injury.
S Move at least 10 feet (3 meters) away from fu-
eling site before starting engine.
S Stop engine and allow it to cool before re-
moving fuel cap.
S Store unit indoors, out of reach of children.
If situations occur which are not covered in this
manual, use care and good judgment. If you
need assistance, call 1--800--554--6723.
SPECIAL NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people proneto circulationdisorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feel-
ing in the fingers, hands, or joints, discontinue
the use of this tool and seek medical attention.
An anti-vibration system does not guarantee
the avoidance of these problems. Users who
operatepower tools on a continual andregular
basis must monitor closely their physical
condition and the condition of this tool.
S Remove fuel cap slowly.
CUTTING SAFETY
WARNING: Inspect the area to be cut
before each use. Remove objects (rocks, bro-
ken glass, nails, wire, string, etc.) which can
be thrown or become entangled inthe blade or
trimmer line.
S Keep others including children, animals, by-
standers, and helpers at least 50 feet (15 me-
ters) away. Bystanders should be encouraged
to wear safety glasses. Stop engine immedi-
ately if you are approached.
S Always keep engine on the right--hand side
of your body.
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not over-
reach.
S Keep blade/trimmer head below waist level.
S Do not raise powerhead engine above your
waist.
S Keep all parts of your body away from spin-
ning line/blade and muffler.
SAVE THESE INSTRUCTIONS
ASSEMBLY
S Wing nut (screwed onto plastic shield)
S Attachment hanger
CARTON CONTENTS
Check carton contents for the following:
S Brushcutter attachment
S Handlebar
S Hex wrench
WARNING: If received assembled, re-
peat all steps to ensure your unit is properly as-
sembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
S Handlebar mounting bracket for 1″ shaft
S Handlebar mounting bracket for 7/8″ shaft
S Bracket cover (2)
S Shoulder strap
S Upper shoulder strap clamp
S Lower shoulder strap clamp (with spacer tabs)
S Handlebar bracket screws (4)
S Shoulder strap clamp screws (2)
S 4--point weed blade (assembled on brush-
cutter attachment)
NOTE:If you need assistance or find that parts
are missing or damaged, call 1-800-554-6723.
TOOLS REQUIRED
S Hex wrench (provided)
S Large nut for installing blade
S Retaining washer
INSTALLING BRUSHCUTTER
S Cupped washer
ATTACHMENT
S Metal shield (assembled on brushcutter at-
tachment)
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
S Trimmer head
S Plastic shield
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Loosen the coupler by turning the knob
counterclockwise.
NOTE: Two mounting brackets are included
with this attachment. Both brackets are provided
to adapt this attachment for use with power-
heads that have either a 1″ (2.5 cm) diameter or
a 7/8″ (2.2 cm) diameter upper shaft. The cor-
rect bracket must be used to ensure that the
handlebar is mounted securely to the upper
shaft before use.
Coup
Attachment
SEN
Screw
Handlebar
Knob
TIGHTEN
2. Remove the shaft cap from the brushcut-
ter attachment (if present).
Bracket Cover
Mountin
Bracket
3. Position locking/release button of attach-
ment into guide recess of coupler.
4. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
1. Place the mounting bracket over the up-
per shaft above the arrow on the safety
label. Be sure to usethe correct mounting
bracket for either the 1″ (2.5 cm) or 7/8″
(2.2 cm) diameter upper shaft.
2. Position one of the bracket covers under
the upper shaft and align the mounting
bracket and the bracket cover screw
holes. Insert two screws into the screw
holes.
3. Secure the mounting bracket by tighten-
ing the screws with the hex wrench.
4. Locate the decal on the handlebar. This
decal includes an arrow. Position the
handlebar with the mounting bracket at
the end of the arrow.
5. Position the second bracket cover over
the handlebar. Align the mounting brack-
et and the bracket cover screw holes.
Again make sure the handlebar is at the
end of the arrow.
5. Before using the unit, tighten the knobse-
curely by turning clockwise.
Primary Hole
Coupler
Guide Recess
Locking/
Release
Button
Upper
Shaft
Attachment
WARNING: Make sure the locking/re-
lease button is locked in the primary hole and
the knob is securely tightened before operat-
ing the unit. Using the wrong hole could lead to
serious injury or damage to the unit.
6. Insert two screws and hand tighten only.
Be sure the handlebar is installed cor-
rectly; then, tighten each screw securely
with the hex wrench.
SHOULDER STRAP ASSEMBLY
WARNING: Proper shoulder strap
and handlebar adjustments must be made
with the engine completely stopped before us-
ing unit. The shoulder strap clamp must be
installed as shown above the handlebar on the
upper shaft (powerhead end of unit).
Locking/Release
Button in Primary Hole
HANDLEBAR ASSEMBLY
NOTE: The lower shoulder strap clamp has
two spacer tabs attached. These tabs arepro-
vided to adapt this attachment for use with
powerheads that have a 1″ (2.5 cm)diameter
upper shaft (the shoulder strap clamp will not
tightendown securely on the1″ (2.5 cm) diam-
eter upper shaft without using these spacer
tabs). The tabs must be broken off completely
before use and placed over the screw holes
on the lower shoulder strap clamp. Thesetabs
are not needed for powerheads with a 7/8″
(2.2 cm) upper shaft.
DANGER:RISK OF CUT. To avoidse-
rious injury, the barrier portion of the handle-
bar must be installed as shown on the upper
shaft of the powerhead to provide a barrier be-
tweenoperator andthespinningblade. Attach
handlebar mounting bracket above arrow on
safety warning decal on the upper shaft (pow-
erhead end of unit). Ensure handlebar is posi-
tioned on mounting bracket at the end of the
arrow on the handlebar decal.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER SHOULDER STRAP
CLAMP
SHOULDER STRAP
ADJUSTMENT
FOR BALANCE
Spacer Tabs
Spacer Tabs
6 inches
(15 cm)
below
4 -- 12 inches
positioned for use
on 1″ (2.5 cm)
diameter
30 inches
(10 -- 30 cm)
above
(76 cm)
waist
minimum
ground
upper shaft
1. Place the upper shoulder strap clamp
over theupper shaft above the handlebar.
2. Position the lower shoulder strap clamp
under the upper shaft and align the upper
and lower clamp screw holes (usespacer
tabs between upper and lower clamps if
necessary to secure clamp, i.e. for 1″ (2.5
cm) diameter upper shaft).
30 inches
(76 cm)
minimum
houlder
amp
POWERHEAD
END
CONFIGURING YOUR UNIT
You can configure your unit using a trimmer
head for grass and light weeds, or a weed blade
for cutting grass, weeds, and brush up to 1/2
inch (1 cm) in diameter. To assemble your unit,
go to the section for the desired configuration
and follow the instructions.
ATTACHMENT
Lower Shoulder
END
Strap Clamp
Screws
ASSEMBLY INFORMATION --
TRIMMER HEAD
3. Insert two screws into the screw holes.
4. Secure shoulder strap clamp by tighten-
ing screws with the hex wrench.
TRIMMER
HEAD
5. Insert your right arm and head through
the shoulder strap and allow it to rest on
your left shoulder. Make sure the danger
sign is on your back and the hook is to the
right side of your waist.
NOTE: A one-half twist is built in theshoulder
strap to allow the strap to rest flat on theshoul-
der.
6. Adjust the strap, allowing the hook to be
about 6 inches below the waist.
NOTE: Remove the blade and metal shield be-
fore attaching the plastic shield and trimmer
head. To remove blade, align hole in the dust
cup with the hole in the side of the gearbox by
rotating the blade. Insert a small screwdriver
into aligned holes. This will keep the shaft from
turning while loosening the blade nut. Remove
blade nut by turning clockwise. Remove the
screwdriver. Remove both washers and blade.
7. Fasten the strap hook to the clamp and lift
the tool to the operating position.
8. Try on shoulder strap and adjust for fit
and balance before starting the engine or
beginning a cutting operation.
NOTE: It may be necessary to relocate the
shoulder strap clamp on the shaft for proper
balancing of unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove metal shield, loosen and remove the
four mounting screws. See ATTACHING THE
METAL SHIELD and INSTALLATION OF THE
METAL BLADE for illustrations. Be sure to store
all parts and instructions for future use.
INSTALLATION OF THE TRIMMER
HEAD
ASSEMBLY INFORMATION -- WEED
BLADE
WEED
BLADE
NOTE: Before installing the trimmer head,
make sure the dust cup and retaining washer
are positioned on the shaft of the gearbox.
The retaining washer must be positioned with
the raised section toward the gearbox.
1. Align hole in the dust cup with the hole in the
side of the gearbox by rotating the dust cup.
2. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening trimmer head.
NOTE: Remove the trimmer head and plastic
shield before attaching the metal shield and
installing the weed blade. To remove the trimmer
head, align hole in the dust cup with the hole in
the side of the gearbox by rotating the dust cup.
Insert a small screwdriver into aligned holes.
This will keep the shaft from turning while loos-
ening the trimmer head. Remove the trimmer
head by turning clockwise. Remove the screw-
driver. To remove the plastic shield, loosen and
remove wing nut. Pivot shield to release bracket
from slot. See INSTALLATION OF THE TRIM-
MER HEAD and ATTACHING THE PLASTIC
SHIELD for illustrations. Be sure to store all
parts and instructions for future use. Never use
the trimmer head with the metal blade installed.
3. While holding the screwdriver in position,
thread trimmer head onto the shaft by turn-
ing counterclockwise. Tighten until secure.
Gearbox
Dust cup
Retaining
washer
Trimmer
head
ATTACHING THE METAL SHIELD
WARNING: The metal shield must be
properly installed on the tool anytime the tool
is used with a blade. The forward tip of the
metal shield helps to reduce the occurrence of
blade thrust which can cause serious injury
such as amputation to the operator or by-
standers. Failure to install the shield in the
position shown can result in serious injury to
the operator. The length of the shield must be
aligned with the length of the shaft.
4. Remove the screwdriver.
ATTACHING THE PLASTIC SHIELD
WARNING: The shield must be prop-
erly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped witha
line limiter blade which cuts excess line to the
proper length. The line limiter blade (on under-
side of shield) is sharp and can cut you.
1. Remove wing nut from shield.
1. Place the metal shield under the gearbox,
and align the screw holes.
2. Insert bracket into slot on shield.
3. Pivot shield until bolt passes through hole
in bracket.
Gearbox
4. Tighten the wing nut securely.
Wing Nut
Slot
Shield
Bracket
Shield
2. Insert and thread the 4 mounting screws
through the holes of the gearbox and the
metal shield. Tighten evenly and secure-
ly with the hex wrench provided.
Gearbox
PIVOT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF THE METAL
BLADE
Gearbox
Shield
WARNING: Wear protective gloves
when handling or performing maintenance on
the blade to avoid injury. The blade is sharp
and can cut you even when it is not moving.
WARNING: Do not use any blades, or
fastening hardware other than the washers
and nuts shown in the following illustrations.
These parts must be provided by Poulan/
WEED EATER and installed as shown below.
Failure to use proper parts can cause the
blade to fly off and seriously hurt you or others.
NOTE: The dust cup and retaining washer are
located on the gearbox shaft and not in the parts
bag. All other fasteners mentioned in the follow-
ing assembly steps are in the parts bag.
1. Remove the retaining washer from the
threaded shaft of the gearbox. Leave the
dust cup on the shaft.
Dust cup
es
Threaded shaft
Retaining
washer
Blade
Cupped
washer
Nut
2. Install the blade and the retaining washer
over the threaded shaft.
NOTE: Make sure all parts are in place as illus-
trated, and the blade is sandwiched between the
dust cup and the retaining washer. There should
be no space between the blade and the dust cup
or the retaining washer.
3. Make sure the raised part of the retaining
washer is facing the gearbox and the raised
area fits into the hole in the center of the
blade.
7. Align hole in dust cup with hole in side of
gearbox by rotating the blade.
4. Slide the blade and retaining washer onto
the shaft of the gearbox.
8. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening the blade nut.
5. Place the cupped washer onto the shaft.
Make sure the cupped side of the washer
is toward the blade.
9. Tighten blade nut firmly with a wrench
while holding screwdriver in position.
10. Remove the screwdriver.
6. Install the blade nut by threading onto the
shaft counterclockwise.
11. Turn blade by hand. If the blade binds
against the shield, or appears to be un-
even, the blade is not centered, and you
must reinstall.
NOTE: To remove blade, insert screwdriver
into aligned holes. Unthread the nut and remove
parts. Be sure to store parts and instructions for
future use.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR BRUSHCUTTER ATTACHMENT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize yourself
with the location of various controls and adjustments. Save this manual for future reference.
Hanger
Gearbox
Blade Shield
Blade
BLADE
BLADE SHIELD
The BLADE SHIELD provides protection from
the spinning blade.
The BLADE is designed for cutting grass,
weeds, and brush up to 1/2 inch (1 cm) in
diameter.
TRIMMER SHIELD
The TRIMMER SHIELD provides protection
from the spinning trimmer line.
TRIMMER HEAD
The TRIMMER HEAD holds cutting line and is
designed for cutting grass and light weeds.
OPERATING THE COUPLER
Coup
Your powerhead is equipped with a coupler
which enables optional attachments to be
installed. The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . . . . PPB1000E
Cultivator . . . . . . . . . . . . . . . . . . . . PPB2000T
Blower . . . . . . . . . . . . . . . . . . . . . . PPB3000B
Pruner . . . . . . . . . . . . . . . . . . . . . . PPB5000P
Pruner . . . . . . . . . . . . . . . . . . . . . . PPB5500P
Attachment
SEN
Knob
WARNING: Always disconnect pow-
erhead spark plug before removing or instal-
ling attachments.
REMOVING BRUSHCUTTER
ATTACHMENT (OR OTHER
TIGHTEN
2. Press and hold the locking/release button.
Locking/Release
Button
OPTIONAL ATTACHMENTS)
CAUTION: When removing or installing at-
tachments, place the powerhead and attach-
ment on a flat surface for stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Upper Shaft
Attachment
Coupler
3. While securely holding the upper shaft,
pull the attachment straight out of the
coupler.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the shaft cap from the attach-
ment (if present) and discard.
2. Position locking/release button of attach-
ment into guide recess of upper shaft
coupler.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
S Keep arms extended with right handholding
the trigger handle of powerhead.
S Keep left arm extended with left hand hold-
ing the handlebar.
4. Before using the unit, tighten the knobse-
curely by turning clockwise.
S Keep unit below waist level.
Primary Hole
S Shoulder strap pad should be centered on
your left shoulder and danger sign centered
on your back.
Coupler
Guide Recess
S Maintain full weight of tool on left shoulder.
S Without bending over, keep the blade near
and parallel to the ground and not crowded in-
to material being cut.
OPERATING INSTRUCTIONS FOR
USE OF BRUSHCUTTER ATTACH-
MENT WITH TRIMMER HEAD
Locking/
Release
Button
Upper
Shaft
Attachment
WARNING: Make sure the locking/re-
lease button is locked in the primary hole and
the knob is securely tightened before operat-
ing the unit. Using the wrong hole could lead to
serious injury or damage to the unit.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head. Rocks
or debris can ricochet or be thrown into eyes
and face and cause blindness or other serious
injury.
Before trimming, bring engine to a speed suffi-
cient to cut material to be trimmed.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle. At
lower speeds, there is less engine noise and
vibration. Always release the throttle trigger
and allow the engine to return to idle speed
when not cutting.
Locking/Release
TRIMMER LINE ADVANCE
Button in Primary Hole
The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of thetrim-
mer head is tapped on the ground with the en-
gine running at full throttle.
INSTALLING ATTACHMENT
HANGER
The most efficient line length is the maximum
length allowed by the line limiter. Always keep
the shield in place when the tool is being oper-
ated.
An attachment hanger is provided for storage
when attachment is not in use. To install hang-
er on attachment:
1. Remove the shaft cap from the attach-
ment (if present) and discard.
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to and above
the grassy area.
2. Press and hold the locking/release but-
ton.
3. Push hanger onto the attachment until the
locking/release button snaps into the hole.
S Tap the bottom of the trimmer head lightly on
the ground one time.
OPERATING POSITION
ALWAYS WEA
Approximately 2 inches (5 cm) of line will be ad-
vanced with each tap. Always tap the trimmer
head on a grassy area. Tapping on surfaces
such as concrete or asphalt can causeexces-
sive wear to the trimmer head.
Protection
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
Heavy,
Long Pants
WARNING: Use only 0.080″ (2 mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off duringcut-
ting and become a dangerous missile that can
cause serious injury.
Boots
Cut from your left to your right.
NOTE: This brushcutter attachment is not
designed for use with electric powerheads.
CUTTING METHODS
When operating unit with brushcutter attach-
ment, clip shoulder strap onto upper shoulder
strapclamp, standas shown andcheck for the
following:
WARNING: Use minimum speed and
donot crowdtheline whencutting aroundhard
objects (rock, gravel, fence posts, etc.), which
candamagethetrimmer head, become entan-
S Wear eye protection and heavy clothing.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
gled in the line, or be thrown causing a serious
hazard.
S The tip of the line does the cutting. You will
achieve the best performance andminimum
line wear by not crowding the line into the
cutting area. The right and wrong ways are
shown below.
parallel totheground. Avoid pressing thehead
into the ground as this can scalp the ground
and damage the tool.
Mowing
Tip of the line
does the cutting.
Line crowded into
work area.
SWEEPING -- The fanning action of the rotat-
ing line can be used to blow away loose debris
from an area. Keep the line parallel to and
above the area surface and swing the tool
from side to side.
Right
Wrong
S The line will easily remove grass and weeds
from around walls, fences, trees and flower
beds, but it also can cut the tender bark of
trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
Sweeping
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
OPERATING INSTRUCTIONS FOR
BRUSHCUTTER ATTACHMENT
S Blade Thrust is a reaction that only occurs
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefully study this section. It is important that
you understand what causes blade thrust,
how you can reduce the chance of its occur-
ring, and how you can remain in control of unit
if blade thrust occurs.
Trimming
S WHAT CAUSES BLADE THRUST -- Blade
Thrust can occur when spinning blade con-
tacts an object that it does not cut. This contact
causes blade to stop for an instant and then
suddenly move or “thrust” away from object
that was hit. The “thrusting” reaction can be
violent enough to cause operator to be pro-
pelled in any direction and lose control of unit.
The uncontrolled unit can cause serious injury
if blade contacts operator or others.
3 inches (8 cm)
above ground
SCALPING -- The scalping technique re-
moves unwanted vegetation down to the
ground. Hold the bottom of the trimmer head
about 3 inches (8 cm) above theground and at
an angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
S WHEN BLADE THRUST OCCURS
-
Blade Thrust can occur without warning if
the blade snags, stalls, or binds. This is
more likely to occur in areas where it is diffi-
cult to see the material being cut. By using
the unit properly, the occurrence of blade
thrust will be reduced and the operator will
be less likely to lose control.
Scalping
S Cut only grass, weeds, and woody brush up to
1/2 inch (1 cm) in diameter with weed blade.
Do not let blade contact material it cannot cut
such as stumps, rocks, fences, metal, etc., or
clusters of hard, woody brush with a diameter
greater than 1/2 inch (1 cm).
MOWING -- Your trimmer is ideal for mowingin
places conventional lawn mowers cannot
reach. In the mowing position, keep the line
S Usea sharp blade. A dull blade is morelikely
to snag and thrust.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S Cut only at full throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
The blade should not turn while the engine is
running at idle. If the blade turns at idle, do not
use your unit. Refer to the CARBURETOR
ADJUSTMENT section of the powerhead
manual or contact your authorized service
dealer.
S “Feed” the blade deliberately and not too
rapidly. The blade can thrust away if it is fed
too rapidly.
S Cut only from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator.
S Maintain good firm footing while using the
unit. Do this by planting feet firmly in a com-
fortable apart position.
S Use the shoulder strap and keep a firm grip
on the unit with both hands. A properly ad-
justed shoulder strap will support the weight
of the unit, freeing your arms and hands to
control and guide the cutting motion.
S Keep feet comfortably spread apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
S Cut while swinging the upper part of your
body from left to right.
S As you move forward to the next area to cut,
be sure to maintain your balance, and footing.
RECOMMENDED CUTTING POSITION
2 o’clock
Cut using the 2
o’clock to 4 o’clock
position of the
blade
4 o’clock
S Keep blade below waist level. It will be eas-
ier to maintain control of unit.
S Do not raise the engine above your waist as
the blade can come dangerously close to
your body.
S Do not swing the unit with such force that
you are in danger of losing your balance.
Bring the powerhead engine to cutting speed
before entering the material to be cut. If the
blade does not turn when you squeeze the
throttle trigger of the powerhead, make sure
the attachment is fully inserted into the cou-
pler. Always release the throttle trigger and al-
low powerhead engine to return to idle speed
when not cutting.
WARNING: The operator or others
must not try to clear away cut material with the
engine running or the blade turning to avoid
serious injury. Stop engine and blade before
removing materials wrapped around blade or
shaft.
MAINTENANCE
BLADE MAINTENANCE
WARNING: Always stop unit and dis-
connect spark plug wire before performing
maintenance.
CHECK FOR DAMAGED OR
WORN PARTS
WARNING: The blade will continue to
spin after the engine stops or after the throttle
trigger has been released. To avoid serious
injury, make sure the blade has stopped
coasting anddisconnect the spark plug before
performing work on the blade.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Blade Shield -- Discontinue use of brushcut-
ter attachment if blade shield is damaged.
S Trimmer Shield -- Discontinue use of brush-
cutter attachment if trimmer shield is dam-
aged.
WARNING: Always replace a blade
that is bent, warped, cracked, broken, or dam-
aged in any other way. Never attempt to
straighten and reuse a damaged blade. Use
only specified replacement blade. Wear pro-
tective gloves when handling or performing
maintenance on the blade to help avoid injury.
S Check blade for flatness periodically. Lay
the blade on a flat surface to inspect for flat-
ness. Throw away a blade that is not flat.
CHECK FOR LOOSE FASTENERS
AND PARTS
S Blade nut
S Fasteners
INSPECT AND CLEAN UNIT
AND DECALS
S After each use, inspect complete unit for loose
or damaged parts. Clean the unit and decals
using a damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
5. Wind the line evenly and tightly onto the
REPLACING THE LINE
spool. Wind in the direction of the arrows
found on the spool.
1. Remove spool by firmly pulling on tapbut-
ton.
6. Push the lines into the notches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
7. Insert the lines into the the exit holes in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080″ (2 mm) di-
ameter Poulan PRO brand line.
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
10. Pull the lines extending outside of thehub
to release the lines from the notches.
TRIMMER HEAD REPLACEMENT
Refer to the ASSEMBLY section for trimmer
head replacement instructions and illustra-
tions.
Spool
Small
Holes
BLADE REPLACEMENT
Refer to the ASSEMBLY section for blade re-
placement instructions and illustrations.
Line exit holes
Line in Notch
Line in Notch
Hub
STORAGE
S Clean the entire attachment.
S Inspect the blade shield area and clean any
dirt, grass, leaves, or debris that has col-
lected. Inspect the blade and blade shield;
WARNING: Perform the following
steps after each use:
S Allow attachment and gearbox to cool be-
fore storing or transporting.
replace
a
blade that is bent, warped,
cracked, broken or damaged in any other
way.
S Store attachment with blade shield in place.
Position attachment so that any sharp ob-
ject cannot accidentally cause injury.
S Store the attachment in a dry, wellventilated
area out of the reach of children.
S Lightly oil external metal surfaces.
S Apply a coating of oil to the entire surface of
the blade; wrap it in heavy paper or cloth.
S Check entire attachment for loose screws
or nuts. Replace any damaged, worn or
broken parts.
SEASONAL STORAGE
Prepare attachment for storage at end of sea-
son or if it will not be used for 30 days or more.
If your brushcutter attachment is to be stored
for a period of time:
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Poulan PRO, a division of Husqvarna Consum-
In Canada, contact:
er Outdoor Products N.A., Inc., warrants to the
original consumer purchaser that each new
Poulan PRO brand gasoline tool or attachment
is free from defects in material and workmanship
and agrees to repair or replace under this war-
ranty any defective gasoline product or attach-
ment as follows from the original date of pur-
chase.
Poulan PRO
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from whom
it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC LE-
GAL RIGHTS, AND YOU MAY HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED, AND
THERE ARE NO OTHER EXPRESS WAR-
RANTIES EXCEPT THOSE EXPRESSLY
STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for com-
mercial, professional, or income producing pur-
poses.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan PRO for
this tool. This warranty does not cover cutting
line or rotating head parts that will wear and re-
quire replacement with reasonable use during
the warranty period. This warranty does not
cover pre--delivery setup or normal adjustments
explained in the instruction manual. This warran-
ty does not cover transportation costs.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan PRO
reserves the right to change, modify, or dis-
continue models, designs, specifications, and
accessories of all products at any time without
notice or obligation to any purchaser.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|