Poulan Snow Blower XT11530ES User Manual

IMPORTANT MANUAL  
Do Not Throw Away  
OWNER'S MANUAL  
MODEL NUMBER:  
WARNING:  
Read the Owner's Manual and  
follow all Warnings and Safety  
Instructions. Failure to do so  
can result in serious injury.  
XT11530ES  
SNOW THROWER  
437970 08.18.10 JA  
Printed in the U.S.A.  
Always Wear Eye Protection During Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Whencleaning,repairingorinspectingthesnowthrower,  
stop the engine and make certain the collector/impel-  
ler and all moving parts have stopped. Disconnect  
the spark plug wire and keep the wire away from the  
plug to prevent someone from accidentally starting the  
engine.  
7. Do not run the engine indoors, except when starting  
the engine and for transporting the snow thrower in or  
out of the building. Open the outside doors; exhaust  
fumes are dangerous.  
16. Never touch a hot engine or muffler.  
Clearing a Clogged Discharge Chute  
Handcontactwiththerotatingimpellerinsidethedischarge  
chute is the most common cause of injury associated with  
snow throwers. Never use your hand to clean out the dis-  
charge chute. To clear the chute:  
1. SHUT THE ENGINE OFF!  
2. Wait 10 seconds to be sure the impeller blades have  
stopped rotating.  
8. Exercise extreme caution when operating on slopes.  
3. Always use a clean-out tool, not your hands.  
9. Neveroperatethesnowthrowerwithoutproperguards,  
and other safety protective devices in place and work-  
ing.  
Maintenance and Storage  
1. Check shear bolts and other bolts at frequent intervals  
for proper tightness to be sure the equipment is in safe  
working condition.  
10. Never direct the discharge toward people or areas  
where property damage can occur. Keep children and  
others away.  
2. Never store the machine with fuel in the fuel tank  
inside a building where ignition sources are present  
such as hot water heaters, space heaters, or clothes  
dryers. Allow the engine to cool before storing in any  
enclosure.  
3. Always refer to operator’s manual for important details  
if the snow thrower is to be stored for an extended  
period.  
4. Maintain or replace safety and instruction labels, as  
necessary.  
5. Run the machine a few minutes after throwing snow  
to prevent freeze-up of the collector/impeller.  
11. Do not overload the machine capacity by attempting  
to clear snow at too fast a rate.  
12. Never operate the machine at high transport speeds  
on slippery surfaces. Look behind and use care when  
operating in reverse.  
13. Disengage power to the collector/impeller when snow  
thrower is transported or not in use.  
14. Use only attachments and accessories approved by  
the manufacturer of the snow thrower (such as wheel  
weights, counterweights, or cabs).  
15. Never operate the snow thrower without good visibility  
or light. Always be sure of your footing, and keep a firm  
hold on the handles. Walk; never run.  
CONGRATULATIONS on your purchase of a new snow  
thrower. It has been designed, engineered and manufac-  
tured to give best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity 3.0 Quarts (2,83 Liters)  
Should you experience any problem you cannot easily  
remedy, please contact your nearest authorized service  
center. We have competent, well-trained technicians and  
the proper tools to service or repair this unit.  
and Type:  
Unleaded Regular only  
Oil Type  
(API SG–SL):  
SAE 5W-30 or 10W-30  
Synthetic SAE 5W-30  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your snow thrower  
properly. Always observe the “SAFETY RULES”.  
Oil Capacity:  
28 Ounces (0,82 Liters)  
Spark Plug:  
Gap:  
Champion QC12YC  
0.030" (0,762 mm)  
SERIAL NUMBER: ___________________________  
DATE OF PURCHASE: _______________________  
THEMODELANDSERIALNUMBERSWILLBEFOUND  
ONADECALATTACHEDTOTHEREAROFTHESNOW  
THROWER HOUSING.  
CUSTOMER RESPONSIBILITIES  
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your snow thrower.  
YOUSHOULDRECORDBOTHSERIALNUMBERAND  
DATE OF PURCHASE AND KEEP IN A SAFE PLACE  
FOR FUTURE REFERENCE.  
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
TABLE OF CONTENTS  
SAFETY RULES ........................................................ 2-3  
MAINTENANCE..................................................... 14-15  
SERVICE AND ADJUSTMENTS........................... 16-18  
STORAGE................................................................... 19  
TROUBLESHOOTING................................................ 20  
REPAIR PARTS ..................................................... 22-40  
WARRANTY...............................................BACK PAGE  
PRODUCT SPECIFICATIONS...................................... 3  
CUSTOMER RESPONSIBILITIES................................ 3  
ASSEMBLY / PRE-OPERATION ............................... 4-7  
OPERATION ............................................................ 8-13  
MAINTENANCE SCHEDULE ..................................... 14  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS PACKED SEPARATELY IN CARTON  
(1) MULTI-  
WRENCH  
(180684)  
(1) FUEL STABILIZER PACKET  
SAFTEY IGNITION KEY(S)  
(193071)  
(1) POWER CORD  
(198563)  
(1) AUGER CONTROL ROD  
(2) FLAT WASHERS  
(1) DISCHARGE CHUTE  
EXTRA SHEAR BOLTS AND NUTS  
(2) SHOULDER  
BOLT 1/4-20 x 1-3/4  
(192090)  
(2) LOCKNUTS  
1/4-20  
(73800400)  
(2) CARRIAGE BOLTS  
3/8-16 x 2.25  
ROTATOR HEAD MOUNTING  
(3) RETAINER  
SPRINGS  
(169675)  
(2) HANDLE KNOBS  
(1) WASHER 3/8  
(19131316)  
(1) LOCKNUT 3/8  
(73800600)  
CHUTE DEFLECTOR REMOTE CONTROL  
(1) LOCKNUT (1) CARRIAGE BOLT  
(1) LOCKNUT  
1/4-20  
(191730)  
(1) SHOULDER  
BOLT 1/4-20  
(179829)  
(1) SPRING  
(184505)  
5/16-18  
5/16-18 x 5/8  
(72250505)  
(751153)  
ASSEMBLY / PRE-OPERATION  
Read these instructions and this manual in its entirety  
before you attempt to assemble or operate your new  
snow thrower. Reading the entire manual will familiar-  
ize you with the unit, which will assist you in assembly,  
operation and maintenance of the product.  
2. Cut down all four corners of carton and lay panels flat.  
3. Removethetwo(2)screwssecuringtheaugerhousing  
to the pallet.  
4. Removeallpackingmaterialsexceptplastictieholding  
speed control rod to lower handle.  
Your new snow thrower has been assembled at the factory  
with the exception of those parts left unassembled for ship-  
ping purposes. All parts such as nuts, washers, bolts, etc.,  
necessary to complete the assembly have been placed in  
the parts bag. To ensure safe and proper operation of your  
snow thrower, all parts and hardware you assemble must  
be tightened securely. Use the correct tools as necessary  
to ensure proper tightness.  
5. Remove the two (2) plastic ties securing the upper  
handle to the pallet.  
6. Remove snow thrower from carton and check carton  
thoroughly for additional loose parts.  
HOW TO SET UP YOUR SNOW THROWER  
TOOL BOX (See Fig. 10)  
A toolbox is provided on your snow thrower. The toolbox is  
located on top of the belt cover. Store the extra shear bolts,  
nuts and multi-wrench provided in parts bag in the toolbox.  
REMOVE SNOW THROWER FROM CARTON  
1. Remove all accessible loose parts and parts boxes  
from carton.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
NOTE: The multi-wrench may be used for assembly of the  
INSTALL TRACTION DRIVE CONTROL ROD  
(See Figs. 3 and 4)  
The traction drive control rod is installed on the snow  
thrower.  
chuterotatorheadtosnowthrowerandmakingadjustments  
to the skid plates.  
UNFOLD UPPER HANDLE  
1. Raise upper handle to the operating position and  
tighten handle knobs securely. Additional carriage  
bolts, washers and handle knobs are in bag of parts.  
Use to secure upper handle to lower handle. Install  
in lower holes in handles.  
1. Remove plastic tie securing rod to lower handle.  
2. With top end of rod positioned under left side of control  
panel, pushroddownandinserttopendofrodintohole  
in drive control bracket. Secure with retainer spring.  
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)  
PLASTIC TIE  
1. Remove plastic tie securing rod to lower handle.  
2. Insert rod into speed control bracket and secure with  
retainer spring.  
TRACTION DRIVE  
CONTROL ROD  
SPEED  
CONTROL  
ROD  
VINYL  
SLEEVE  
PLASTIC TIE  
UPPER  
HANDLE  
HANDLE  
KNOB  
LOWER  
HANDLE  
FIG. 3  
TRACTION DRIVE  
CONTROL LEVER  
RETAINER  
SPRING  
FIG. 1  
TRACTION  
SPEED CONTROL ROD  
DRIVE  
CONTROL  
ROD  
RETAINER  
SPRING  
DRIVE  
CONTROL  
BRACKET  
FIG. 4  
SPEED  
CONTROL  
BRACKET  
SPEED  
CONTROL  
LEVER  
FIG. 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
ASSEMBLY / PRE-OPERATION  
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR  
HEAD (See Fig. 7)  
NOTE: The multi-wrench provided in your parts bag may  
be used to install the chute rotator head.  
1. Place discharge chute assembly on top of chute base  
with discharge opening toward front of snow thrower.  
2. Positionchuterotatorheadoverchutebracket. Ifneces-  
sary,rotatechuteassemblytoalignsquareandpinonun-  
dersideofchuterotatorheadwithholesinchutebracket.  
3. With chute rotator head and chute bracket aligned,  
position chute rotator head on pin and threaded stud  
of mounting bracket.  
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)  
1. Retrieve vinyl sleeve and spring from bag of parts and  
retrieve the auger control rod from carton chute tray.  
Slide straight rod end through the small hole in the  
vinyl sleeve. Hook spring in hole in rod end.  
2. Hook end of spring into control arm with loop opening  
up as shown. (See Fig. 5)  
3. With top end of rod positioned under right side of  
control panel, push down on rod and insert end of rod  
intoholeinaugercontrolbracket. Securewithretainer  
spring.  
4. Install 3/8 washer and locknut on threaded stud and  
tighten securely.  
AUGER  
CONTROL  
ROD  
CHUTE  
ROTATOR  
HEAD  
3/8 LOCKNUT  
3/8 WASHER  
VINYL  
SLEEVE  
CONTROL  
ARM  
PIN  
THREADED  
STUD  
LOOP  
OPENING  
UP  
ROTATOR HEAD  
MOUNTING  
ALIGN BEFORE  
TIGHTENING LOCKNUT  
CHUTE  
BRACKET  
BRACKET  
FIG. 7  
FIG. 5  
AUGER CONTROL ROD  
AUGER  
CONTROL  
LEVER  
RETAINER  
SPRING  
AUGER  
CONTROL  
BRACKET  
FIG. 6  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
INSTALL CHUTE DEFLECTOR REMOTE CONTROL  
(See Figs. 8 and 9)  
1. Install remote cable bracket to discharge chute with  
5/16-18 carriage bolt and 5/16-18 locknut as shown.  
Tighten securely.  
2. Install remote cable eyelet to chute deflector with  
1/4-20 shoulder bolt and 1/4-20 locknut as shown.  
Tighten nut securely. Eyelet will be loose on shoulder  
bolt.  
3. Install spring hooks between hex nuts on chute rotater  
head and into hole in chute deflector as shown.  
SPRING  
1/4-20  
CHUTE  
SHOULDER  
DEFLECTOR  
BOLT  
HOOK  
BETWEEN  
HEX NUTS  
ON CHUTE  
ROTATER  
HEAD  
1/4-20  
LOCKNUT  
5/16-18  
CARRIAGE  
BOLT  
CABLE  
EYELET  
REMOTE  
CABLE  
BRACKET  
5/16-18  
LOCKNUT  
FIG. 8  
CHUTE DEFLECTOR  
CONTROL LEVER  
FIG. 9  
CHECK TIRE PRESSURE  
Thetiresonyoursnowthrowerwereoverinflatedatthefac-  
tory for shipping purposes. Correct and equal tire pressure  
is important for best snow throwing performance.  
Reduce tire pressure to 14-17 PSI.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR SNOW THROWER  
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare  
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save  
this manual for future reference.  
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand  
their meaning.  
PRIMER  
DANGER  
OR WARNING  
READ AND FOLLOW ALL SAFETY INFORMATION  
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.  
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
FORWARD REVERSE  
IGNITION KEY.  
INSERT TO START  
AND RUN,  
PULL OUT TO STOP.  
DISENGAGED  
ENGAGED  
SNOW  
TRACTION  
DISCHARGE  
DRIVE CONTROL  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
DISCHARGE CHUTE  
CONTROL LEVER  
GASOLINE  
ELECTRIC  
AUGER  
DRIVE  
FILLER CAP  
START BUTTON  
CONTROL  
LEVER  
SPEED  
CONTROL  
LEVER  
DEFLECTOR REMOTE  
RECOIL  
CONTROL LEVER  
MUFFLER  
(AUXILIARY)  
STARTER  
HANDLE  
TRACTION  
DRIVE  
CONTROL  
LEVER  
CHUTE  
DEFLECTOR  
CHOKE  
CON-  
TROL  
PRIMER  
LH TURN  
TRIGGER  
SAFETY  
IGNITION  
KEY  
DISCHARGE  
CHUTE  
LIGHT  
ON / OFF  
SWITCH  
HANDLE  
KNOB  
CLEAN-OUT  
TOOL  
MUFFLER  
TOOLBOX  
NOTE: ITEMS ABOVE  
ARE SHOWN IN  
THEIR TYPICAL  
LOCATION ON THE  
ENGINE. ACTUAL  
LOCATION MAY VARY  
WITH THE ENGINE  
ON YOUR UNIT.  
SKID PLATE  
AUGERS  
FIG. 10  
MEETS A.N.S.I. SAFETY REQUIREMENTS  
Our snow throwers conform to the standards of the American National Standards Institute.  
Toolbox - used to store spare shear bolts, locknuts and  
ON / OFF switch - used to STOP the engine.  
wrench.  
Traction drive control lever - used to engage power-  
propelled forward or reverse motion of snow thrower.  
Safety ignition key - must be inserted for the engine to  
start and run. Remove when snow thrower is not in use.  
Auger control lever - used to engage auger motion (throw  
snow).  
Electric start button - used for starting the engine.  
Recoil (auxiliary) starter handle - used for starting the  
engine.  
Deflector remote control lever - used to change the  
distance the snow is thrown.  
Primer - pumps additional fuel from the carburetor to the  
cylinder for use when starting a cold engine.  
Discharge chute control lever - used to change the di-  
rection the snow is thrown.  
LH and RH turn triggers - used to steer the snow thrower.  
Skid plate - used to adjust height of scraper bar from the  
ground.  
Choke control - used for starting a cold engine.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any snow thrower can result  
TheDIRECTIONinwhichsnowistobethrowniscontrolled  
by the discharge chute control lever.  
in foreign objects thrown into the eyes, which  
canresultinsevereeyedamage. Alwayswear  
safety glasses or eye shields while operating  
your snow thrower or performing any adjust-  
Tochangethedischargechuteposition,pressdownward  
on discharge chute control lever and move lever left  
or right until chute is in desired position. Be sure lever  
springs back and locks into desired position.  
00155  
ments or repairs. We recommend standard safety glasses  
or a wide vision safety mask worn over spectacles.  
The DISTANCE that snow is thrown is controlled by the  
position of the chute deflector. Set the deflector low to  
throw snow a short distance; set the deflector higher to  
throw snow farther.  
HOW TO USE YOUR SNOW THROWER  
Know how to operate all controls before adding fuel or  
attempting to start the engine.  
Press downward on chute deflector control lever and  
move lever forward to raise the deflector and increase  
the distance. Move lever back to lower the deflector  
and decrease the distance. Be sure lever springs back  
and locks into desired position.  
STOPPING  
TRACTION DRIVE  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
DISCHARGE CHUTE  
CONTROL LEVER  
AUGER  
Release the auger control lever to stop throwing snow.  
ENGINE  
1. Move ON / OFF switch to “OFF” position.  
2. Remove (do not turn) safety ignition key to prevent  
unauthorized use.  
NOTE: Never use choke to stop engine.  
TO USE CHOKE CONTROL (See Fig. 11)  
The choke control is located on the engine. Use the choke  
control whenever you are starting a cold engine. Do not  
use to start a warm engine.  
CHUTE DEFLECTOR  
REMOTE CONTROL LEVER  
To engage choke, turn knob counterclockwise. Slowly  
turn knob clockwise to disengage.  
FIG. 12  
TO THROW SNOW (See Fig. 13)  
The auger rotation is controlled by the auger control lever  
located on the right side handle.  
Squeeze auger control lever to handle to engage the  
auger and throw snow.  
Release the auger control lever to stop throwing snow.  
AUGER  
CONTROL  
LEVER  
OFF  
FULL  
FIG. 11  
TO CONTROL SNOW DISCHARGE (See Fig. 12)  
WARNING: Snow throwers have ex-  
posed rotating parts, which can cause  
severeinjuryfromcontact, orfromma-  
terialthrownfromthedischargechute.  
Keep the area of operation clear of all  
persons, small children and pets at all  
times including startup.  
WARNING: If the discharge chute or  
augerbecomeclogged,shut-offengine  
andwaitforallmovingpartstostop.Use  
the clean-out tool, NOT YOUR HANDS,  
to unclog the chute and/or auger.  
FIG. 13  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
USING THE CLEAN-OUT TOOL (See Fig. 14)  
CAUTION: Do not move speed control lever  
when traction drive control lever is engaged.  
Damage to the snow thrower can result.  
In certain snow conditions, the discharge chute may be-  
come clogged with ice and snow. Use the clean-out tool  
to dislodge this blockage.  
Slower speeds are for heavier snow and faster speeds  
are for light snow and transporting the snow thrower. It  
is recommended that you use a slower speed until you  
are familiar with the operation of the snow thrower.  
When cleaning, repairing, or inspecting, make  
certain all controls are disengaged and the au-  
ger/impellerandallmovingpartshavestopped.  
Disconnect the spark plug wire and keep the  
wire away from the spark plug to prevent ac-  
cidental starting.  
NOTE: When both traction drive and auger control levers  
are engaged, the traction drive control lever will lock the  
auger control lever in the engaged position. This will allow  
you to release your right hand from the handle and adjust  
the discharge chute direction without interrupting the snow  
throwing process.  
Releasetheaugercontrolleverandshutofftheengine.  
Removetheclean-outtoolfromit'smountingclip. Grasp  
the tool firmly by the handle and push and twist the tool  
into the discharge chute to dislodge the blockage.  
TRACTION DRIVE  
CONTROL LEVER  
Afterthepackedsnowhasbeendislodged,returntheclean-  
out tool to it's mounting clip by pushing it into the clip.  
Makesurethedischargechuteispointedinasafedirec-  
tion(novehicles,buildings,people,orotherobjectsare  
inthedirectionofdischarge)beforerestartingtheengine.  
Restart the engine, then squeeze the auger control  
lever to the handle to clear snow from the auger hous-  
ing and the discharge chute.  
DRIVE SPEED  
CONTROL LEVER  
DISCHARGE CHUTE  
FIG. 15  
POWER STEERING OPERATION (See Fig. 16)  
Steering triggers are used to assist in steering your  
snow thrower. The triggers are located on the underside  
of each handle. When a trigger is squeezed, it disen-  
gages the drive wheel on that side of snow thrower and  
allows it to turn in that direction.  
CLEAN-OUT  
TOOL  
MOUNTING  
CLIP  
To turn left – squeeze left side trigger.  
To turn right – squeeze right side trigger.  
LH TURN  
TRIGGER  
RH TURN  
TRIGGER  
FIG. 14  
TO MOVE FORWARD AND BACKWARD (See Fig. 15)  
SELF-PROPELLING, forward and reverse movement of  
the snow thrower, is controlled by the traction drive control  
lever located on the left side handle.  
Squeezetractiondrivecontrollevertohandletoengage  
the drive system.  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
SPEED and DIRECTION are controlled by the drive speed  
control lever.  
Press downward on the speed control lever and move  
lever to desired position BEFORE engaging the trac-  
tion drive control lever. Be sure lever springs back and  
locks into desired position.  
FIG. 16  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO ADJUST SKID PLATES (See Fig. 17)  
WARNING: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
NOTE: The wrench provided in your parts bag may be  
used to adjust the skid plates.  
Skid plates are located on each side of the auger housing  
and adjust the clearance between the scraper bar and the  
ground surface. Adjust skid plates evenly to proper height  
for current surface conditions. For removal of snow in  
normal conditions, such as a paved driveway or sidewalk,  
place skid plates in the highest position (lowest scraper  
clearance) to give a 1/8" clearance between the scraper  
bar and the ground. Use a middle position if the surface  
to be cleared is uneven.  
CAUTION: Alcohol blended fuels (called gaso-  
hol or using ethanol or methanol) can attract  
moisture which leads to separation and forma-  
tion of acids during storage. Acidic gas can  
damage the fuel system of an engine while in  
storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
NOTE: It is not recommended to operate the snow thrower  
overgravelorrockysurfaces.Objectssuchasgravel,rocks  
or other debris, can easily be picked up and thrown by the  
impeller, which can cause serious personal injury, property  
damage or damage to the snow thrower.  
If snow thrower must be operated over gravel surface,  
use extra caution and be sure skid plates are adjusted  
to lowest (highest scraper clearance) position.  
1. Shut off engine and wait for all moving parts to stop.  
CHOKE  
CONTROL  
GASOLINE  
FILLER CAP  
ENGINE OIL  
FILL CAP / DIPSTICK  
2. Adjust skid plates by loosening the hex nuts, then  
moving skid plate to desired position. Be sure both  
plates are adjusted evenly. Tighten securely.  
HIGH POSITION  
(LOW GROUND  
CLEARANCE)  
STARTER  
BUTTON  
AUGER  
HOUSING  
SCRAPER BAR  
HEX  
SKID PLATE  
NUTS  
LOW POSITION (HIGH GROUND CLEARANCE)  
FIG. 17  
PRIMER  
RECOIL  
STARTER  
HANDLE  
SCRAPER BAR (See Fig. 17)  
SAFETY  
IGNITION  
KEY  
The scraper bar is not adjustable, but is reversible. After  
considerable use it may become worn. When it has worn  
almost to the edge of the housing, it can be reversed,  
providing additional service before requiring replacement.  
Replace a damaged or worn scraper bar.  
ON / OFF  
SWITCH  
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.  
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.  
FIG. 18  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL (See Fig. 18)  
The engine on your snow thrower has been shipped from  
the factory already filled with oil.  
1. Check engine oil with snow thrower on level ground.  
2. Remove oil fill cap/dipstick and wipe clean, reinsert  
the dipstick and screw tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
To change engine oil, see “TO CHANGE ENGINE OIL”  
in the Maintenance section of this manual.  
ADD GASOLINE (See Fig. 18)  
Fill fuel tank to bottom of tank filler neck. Do not over-  
fill. Use fresh, clean, regular unleaded gasoline with  
a minimum of 87 octane. Do not mix oil with gasoline.  
Purchase fuel in quantities that can be used within 30  
days to assure fuel freshness.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE  
5. Pull recoil starter handle quickly. Do not allow starter  
rope to snap back.  
Your snow thrower engine is equipped with both a 120 Volt  
A.C. electric starter and a recoil starter. The electric starter  
is equipped with a three-wire power cord and plug and is  
designed to operate on 120 Volt A.C. household current.  
6. Whentheenginestarts,releasetherecoilstarterhandle  
and slowly move the choke control to the “OFF” posi-  
tion.  
Be sure your house is a 120 Volt A.C. three-wire  
grounded system. If you are uncertain, consult a  
licensed electrician.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operat-  
ing temperature.  
WARM START - RECOIL STARTER  
WARNING: Do not use the electric  
starter if your house is not a 120 Volt  
A.C.three-wiregroundedsystem. Seri-  
ous personal injury or damage to your  
snow thrower could result.  
Follow the steps above, keeping the choke in the “OFF”  
position. DO NOT push the primer.  
BEFORE STOPPING  
Run the engine for a few minutes to help dry off any mois-  
ture on the engine.  
COLD START - ELECTRIC STARTER  
IF RECOIL STARTER HAS FROZEN  
If the recoil starter has frozen and will not turn the engine,  
proceed as follows:  
1. Insert safety ignition key (tied to recoil start cord) into  
ignition slot until it clicks. DO NOT turn the key. Keep  
the extra safety ignition key in a safe place.  
2. Place ON / OFF switch in “ON” position.  
3. Rotate choke control to “FULLposition.  
4. Connect the power cord to the engine.  
5. Plug the other end of the power cord into a three-hole  
grounded 120 Volt A.C. receptacle.  
1. Grasp the recoil starter handle and slowly pull as much  
rope out of the starter as possible.  
2. Release the recoil starter handle and let it snap back  
against the starter.  
If the engine still fails to start, repeat the above steps or  
use the electric starter.  
NOTE: Do not use primer when starting engine with the  
electric starter.  
6. Push starter button until engine starts.  
SNOW THROWING TIPS  
Go slower in deep, freezing or heavy wet snow. Use  
the drive speed control, NOT the ON / OFF switch, to  
adjust speed.  
IMPORTANT: Do not crank engine more than five continu-  
ous seconds between each time you try to start. Wait 5 to  
10 seconds between each attempt.  
7. When the engine starts, release the starter button and  
slowly move the choke control to the “OFF” position.  
It is easier and more efficient to remove snow imme-  
diately after it falls.  
The best time to remove snow is the early morning. At  
this time the snow is usually dry and has not been ex-  
posed to the direct sun and warming temperatures.  
8. Disconnect the power cord from the receptacle first,  
then from the engine.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operat-  
ing temperature.  
Slightly overlap each successive path to ensure all  
snow will be removed.  
Throw snow downwind whenever possible.  
Adjust the skid plates to proper height for current snow  
conditions. See “TO ADJUST SKID PLATES” in this  
section of this manual.  
WARM START - ELECTRIC STARTER  
Follow the steps above, keeping the choke control in the  
“OFF” position.  
For extremely heavy snow, reduce the width of snow  
removal by overlapping previous path and moving  
slowly.  
Keep engine clean and clear of snow during use. This  
will help air flow and extend engine life.  
Aftersnow-throwingiscompleted,allowenginetorunfor  
a few minutes to melt snow and ice off the engine.  
Clean the entire snow thrower thoroughly after each  
use and wipe dry so it is ready for next use.  
COLD START - RECOIL STARTER  
1. Insert safety ignition key (tied to recoil start cord) into  
ignition slot until it clicks. DO NOT turn the key. Keep  
the extra safety ignition key in a safe place.  
2. Place ON / OFF switch in “ON” position.  
3. Rotate choke control to “FULLposition.  
4. Push the primer four (4) times if the temperature is  
below 15°F, or two (2) times if temperature is between  
15° and 50°F. If temperature is above 50°F, priming is  
not necessary.  
WARNING: Do not operate snow  
thrower if weather conditions impair  
visibility. Throwing snow during a  
heavy, windy snowstorm can blind  
you and be hazardous to the safe  
operation of the snow thrower.  
NOTE: Over priming may cause flooding, preventing the  
engine from starting. If you do flood the engine, wait a few  
minutes before attempting to start and DO NOT push the  
primer.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
GENERAL RECOMMENDATIONS  
LUBRICATION CHART  
The warranty on this snow thrower does not cover items  
that have been subjected to operator abuse or negligence.  
To receive full value from the warranty, operator must  
maintain snow thrower as instructed in this manual. Some  
adjustments will need to be made periodically to properly  
maintain your snow thrower. All adjustments in the Service  
and Adjustments section of this manual should be checked  
at least once each season.  
SAE 5W-30 Motor Oil  
See “ENGINE”  
in Maintenance  
section  
General  
Purpose  
Grease  
Once a year, you should replace the spark plug and  
check belts for wear. A new spark plug will help your  
engine run better and last longer.  
Pivot  
points  
Follow the maintenance schedule in this manual.  
NOTE: Use only Original Equipment Manufacturer (OEM)  
parts to service this unit. Failure to do so can cause the unit  
to malfunction and pose a risk of injury to the operator.  
BEFORE EACH USE  
1. Check engine oil level.  
2. Check for loose fasteners.  
3. Checkcontrolstobesuretheyarefunctioningproperly.  
LUBRICATION  
Keep your snow thrower well lubricated  
(See “LUBRICATION CHART”).  
Auger  
grease fittings  
Engine oil  
SNOW THROWER  
Always observe the safety rules when performing any  
maintenance.  
V-BELTS  
Check V-belts for deterioration and wear after every 50  
hours of operation and replace if necessary. The belts  
are not adjustable. Replace belts if they begin to slip from  
wear. (See “TO REMOVE BELT COVER” in the Service  
and Adjustments section of this manual).  
TIRES  
Maintainproperairpressureinbothtires(14–17P.S.I.).  
Keeptiresfreeofgasolineandoil,whichcanharmrubber.  
TheV-beltsonyoursnowthrowerareofspecialconstruction  
andshouldbereplacedbyoriginalequipmentmanufacturer  
(OEM)beltsavailablefromyournearestdealer.Usingother  
than OEM belts can cause personal injury or damage to  
the snow thrower.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
AUGER GEAR CASE  
1. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with plug.  
2. Clean area around drain plug.  
3. Remove drain plug and drain oil in a suitable container.  
4. Install drain plug and tighten securely.  
The gear case was filled with lubricant to the proper  
level at the factory. The only time the lubricant needs  
attention is if service has been performed on the gear  
case.  
If lubricant is required, use only Ronex ED #1 grease.  
TRACTION DRIVE SYSTEM  
5. Wipe off any spilled oil from snow thrower and engine.  
DO NOT lubricate the drive components inside the snow  
thrower. The sprockets, hex shafts, drive disc and friction  
wheel require no lubrication. The bearings and bushings  
are lifetime lubricated and require no maintenance.  
6. Install left wheel (if removed for draining oil). Be sure to  
install klik pin into proper hole in wheel axle (See “TO  
REMOVE WHEELS” in the Service and Adjustments  
section of this manual).  
7. Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine.  
8. Refill engine with oil through oil dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCTSPECIFICATIONSsectionofthismanual.  
CAUTION:Anylubricatingoftheabovecompo-  
nents can cause contamination of the friction  
wheel and damage to the drive system of your  
snow thrower.  
9. Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULLline on dipstick.  
ENGINE  
See engine manual.  
10. Wipe off any spilled oil.  
LUBRICATION  
MUFFLER  
Use only high quality detergent oil rated with API service  
classification SG–SL. Select the oil's SAE viscosity grade  
according to your expected operating temperature.  
Inspect and replace corroded muffler as it could create a  
fire hazard and/or damage.  
SPARK PLUG  
Replacesparkplugatthebeginningofeachseasonorafter  
every100hoursofoperation,whicheveroccursfirst. Spark  
plug type and gap setting are shown in the “PRODUCT  
SPECIFICATIONS” section of this manual.  
CLEANING  
IMPORTANT: For best performance, keep snow thrower  
housing free of any dirt or trash. Clean the outside of your  
snow thrower after each use.  
WARNING: Removesafetyignitionkey  
and disconnect spark plug wire from  
spark plug. Place wire where it cannot  
come in contact with plug.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F. Check your engine oil level more frequently to avoid  
possible engine damage from running low on oil.  
Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.  
Changetheoilafterevery25hoursofoperationoratleastonce  
ayearifthesnowthrowerisnotusedfor25hoursinoneyear.  
We do not recommend using a garden hose to clean  
yoursnowthrowerunlesstheelectricalsystem,muffler  
and carburetor are covered to keep water out. Water  
in engine can result in shortened engine life.  
Checkthecrankcaseoillevelbeforestartingtheengineand  
after each five (5) hours of continuous use. Tighten oil fill  
cap / dipstick securely each time you check the oil level.  
TO CHANGE ENGINE OIL  
Determine temperature range anticipated before next oil  
change.AlloilmustmeetAPIserviceclassificationSG–SL.  
Be sure snow thrower is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
NOTE: The left side wheel may be removed from snow  
thrower for easier access to the oil drain plug and place-  
ment of a suitable container. The unit tilted, resting on the  
frame with the left wheel removed, will help drain any oil  
trapped inside the engine. (See “TO REMOVE WHEELS”  
in the Service and Adjustments section of this manual).  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: To avoid serious injury, before performing any service or adjustments:  
1. Be sure the on/off switch is in the OFF position.  
2. Remove safety ignition key.  
3. Make sure the augers and all moving parts have completely stopped.  
4. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
2. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with spark plug.  
3. Align holes in impeller hub with holes in impeller shaft  
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear  
bolts. Install 1/4-20 locknuts and tighten securely.  
SNOW THROWER  
TO ADJUST SNOW THROWER HEIGHT  
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”  
in the Operation section of this manual.  
CHUTE DEFLECTOR  
The chute deflector, attached to the top of the discharge  
chute, is provided to direct discharging snow away from  
the operator. If the deflector becomes damaged, it should  
be replaced.  
CAUTION: Do not substitute. Use only original  
equipment capscrew/shear bolts as supplied  
with your snow thrower.  
4. Insertsafetyignitionkeyandreconnectsparkplugwire  
to spark plug.  
WARNING: To avoid serious injury,  
never operate your snow thrower with  
the deflector removed or damaged.  
1/4-20  
LOCKNUT  
1/4-20 x 1-5/8  
CAPSCREW /  
SHEAR BOLT  
1/4-20 x 2  
SHOULDER /  
SHEAR BOLT  
Tochangedirectionand/ordistancesnowisdischarged,  
see “TO CONTROL SNOW DISCHARGE” in the Op-  
eration section of this manual.  
IMPELLER HUB  
IMPELLER  
SHAFT  
SHEAR BOLTS (See Fig. 19)  
AUGER SHEAR BOLTS  
Both right and left-hand augers are secured to the auger  
shaft with a shear bolt and hex nut. Should a foreign ob-  
ject or ice become lodged in the augers, the shear bolts  
are designed to break, preventing damage to any other  
components. If one or both augers do not turn when auger  
control lever is engaged, check to see if one or both of the  
bolts have sheared. To replace the shear bolts:  
AUGER  
HUB  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
2. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with spark plug.  
1/4-20  
LOCKNUT  
AUGER HUB  
FIG. 19  
AUGER SHAFT  
3. Align hole in auger hub with hole in auger shaft and  
install a new 1/4-20 x 2" shear bolt. Install 1/4-20  
lock nut and tighten securely.  
TO REMOVE BELT COVER (See Fig. 20)  
1. Remove the two screws securing belt cover to frame.  
2. Remove belt cover.  
CAUTION: Do not substitute. Use only original  
equipment shear bolts as supplied with your  
snow thrower.  
Replace belt cover by installing cover and screws and  
tighten securely.  
4. Insertsafetyignitionkeyandreconnectsparkplugwire  
to spark plug.  
IMPELLER SHEAR BOLTS  
The impeller is secured to the impeller shaft with two (2)  
capscrew/shearboltsandhexnuts. Shouldaforeignobject  
or ice become lodged in the impeller, the capscrews are  
designed to break, preventing damage to any other com-  
ponents. If impeller does not turn when auger control lever  
is engaged, check to see if the capscrews have sheared.  
To replace the capscrew/shear bolts:  
FRAME  
BELT COVER  
FIG. 20  
SCREWS  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE BELTS (See Fig. 21)  
8. RELIEVE TENSION ON TRACTION DRIVE BELT  
IDLER and remove traction drive belt from around  
pulleys.  
The auger and traction drive belts are not adjustable. If  
the belts are damaged or begin to slip from wear, they  
should be replaced. It is recommended that the belt(s) be  
replaced by a service center/department.  
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into  
the square hole in idler arm and rotate ratchet clockwise  
to relieve tension.  
9. With tension relieved on idler, install new traction drive  
belt around pulleys and inside belt keepers.  
10. Install clutch rod in swing plate; secure with hairpin.  
11. Placeaugerbeltaroundandinsidethegrooveofauger  
pulley only.  
12. While your assistant slowly raises handles to rejoin  
the auger housing and frame assembly, pull up on the  
auger belt and squeeze sides together above pulley  
so belt is fully seated in groove of pulley.  
13. Move idler arm so it does not hit impeller pulley as you  
bring snow thrower completely together and check  
carefully for proper routing of belts. If auger belt has  
becomedislodgedfromthepulley(bycatchingtheidler  
arm bracket while bringing snow thrower together),  
separate the snow thrower and repeat step 12. Belt  
must be fully seated in pulley groove when bringing  
the snow thrower together.  
NOTE: It is recommended that both the auger and traction  
drive belt be replaced at the same time.  
The V-belts on your snow thrower are of special construc-  
tion and should be replaced by original equipment manu-  
facturer (OEM) belts available from your nearest service  
center/department. Using other than OEM belts can cause  
personal injury or damage to the snow thrower.  
WARNING: Belt replacement requires  
separation of the snow thrower. While  
separating the auger housing from the  
frame assembly, it is important that  
an assistant stand in the operating  
position and hold the snow thrower  
handles. Serious personal injury and/  
or damage to the unit could occur if  
the snow thrower should fall during  
the belt changing process.  
FRAME  
ASSEMBLY  
AUGER  
HOUSING  
14. Install the two (2) hex bolts and tighten securely.  
15. INSTALLENGINEPULLEY-Placebeltinpulleygroove  
and slide pulley on crankshaft. Install flat washer, bolt  
and tighten securely (41-47 N-m torque). Make sure  
belt is inside belt keeper.  
16. INSTALL BELT COVER and two (2) screws. Tighten  
securely.  
17. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-  
CHARGE CHUTE / CHUTE ROTATER HEAD” in the  
Assembly / Pre-Operation section of this manual.  
HANDLES  
1. REMOVE GASOLINE FROM FUEL TANK - Drain  
gasoline from fuel tank into a suitable container, out-  
doors, away from fire or flame. Wipe up any spilled  
gasoline.  
BELT KEEPER  
TRACTION DRIVE BELT  
ENGINE  
2. REMOVE DISCHARGE CHUTE - Loosen locknut  
securing chute rotator head to mounting bracket only  
enough to allow chute rotator head to be raised and  
discharge chute to be removed from snow thrower.  
3. REMOVE BELT COVER - See “TO REMOVE BELT  
COVER” in this section of this manual.  
4. REMOVEENGINEPULLEY-Removebolt,flatwasher  
securingpulleytoenginecrankshaft. Removeoutside  
(auger) pulley only from crankshaft.  
5. SEPARATE SNOW THROWER - With your assistant  
standing in the operating position holding the handles,  
remove the two (2) bolts holding the auger housing  
and frame together.  
FLAT WASHER  
PULLEY  
BOLT  
AUGER  
BELT  
IDLER ARM  
SQUARE  
HOLE  
CLUTCHING  
IDLER ARM  
BRACKET  
AUGER  
HOUSING  
FRAME  
AUGER PULLEY  
BOLTS  
WARNING: As the last bolt is removed,  
haveyourassistantcarefullylowerthe  
handles down to the ground.  
6. REMOVE HAIRPIN FROM CLUTCH ROD and re-  
move clutch rod from swing plate. Tip swing plate  
forward.  
7. REMOVE AUGER BELT from around pulley.  
FIG. 21  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE WHEELS (See Fig. 22)  
Remove the klik pin and remove wheel from axle.  
TO ADJUST CABLE TENSION (See Fig. 23)  
Adjust cable tension by turning the adjuster turn buckle,  
located on the right hand cable. Grasp the long section  
tightly and turn the short section to lengthen the adjuster.  
Adjust until cable is snug.  
IMPORTANT: When installing wheel, be sure to use the  
axle hole closest to the end of the shaft – do not use the  
hole in the wheel hub (if equipped). Inner hole in axle and  
holeinwheelhubarenotusedforyourmodelsnowthrower.  
KLIK PIN (INSTALL  
IN OUTER HOLE  
OF AXLE ONLY)  
OUTER HOLE  
ADJUSTER TURN  
BUCKLE  
AXLE  
WHEEL  
WHEEL HUB  
FIG. 22  
NOTE: To seal punctures or prevent flat tires due to slow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
FIG. 23  
ENGINE  
See engine manual.  
CARBURETOR  
Your carburetor is not adjustable. Engine performance  
should not be affected at altitudes up to 7,000 feet (2,134  
meters). If your engine does not operate properly due to  
suspected carburetor problems, take your snow thrower  
to a qualified service center.  
ENGINE SPEED  
Never tamper with the engine governor, which is factory set  
for proper engine speed. Overspeeding the engine above  
the factory high speed setting can be dangerous and will  
void the warranty. If you think the engine-governed high  
speed needs adjusting, contact a qualified service center,  
which has proper equipment and experience to make any  
necessary adjustments.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your unit for storage at the end of the  
Empty the fuel tank by starting the engine and letting  
it run until the fuel lines and carburetor are empty.  
season or if the unit will not be used for 30 days or more.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Use fresh fuel next season.  
WARNING: Never store the snow  
throwerwithgasolineinthetankinside  
a building where fumes may reach an  
open flame, spark or pilot light as on a  
furnace, water heater, clothes dryer or  
gasappliance. Allowtheenginetocool  
before storing in any enclosure.  
NOTE: Fuel stabilizer is an acceptable alternative in min-  
imizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not drain the  
gas tank and carburetor if using fuel stabilizer.  
SNOW THROWER  
When snow thrower is to be stored for a period of time,  
clean it thoroughly, remove all dirt, grease, leaves, etc.  
Store in a clean, dry area.  
1. Clean entire snow thrower (See “CLEANING” in the  
Maintenance section of this manual).  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
2. Inspect and replace belts, if necessary (See “TO RE-  
PLACEBELTSintheServiceandAdjustmentssection  
of this manual).  
3. Lubricate as shown in the Maintenance section of this  
manual.  
4. Besurethatallnuts,bolts,screws,andpinsaresecurely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
5. Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
CYLINDER  
1. Remove spark plug.  
2. Pour one ounce (29 ml) of oil through spark plug hole  
into cylinder.  
3. Pullrecoilstarterhandleslowlyafewtimestodistribute  
oil.  
4. Replace with new spark plug.  
OTHER  
Remove safety ignition key; store it in a safe place.  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
ENGINE  
See engine manual.  
FUEL SYSTEM  
If possible, store your snow thrower indoors and cover  
it to protect it from dust and dirt.  
Cover your snow thrower with a suitable protective  
cover that does not retain moisture. Do not use plastic.  
Plastic cannot breathe, which allows condensation to  
form and will cause your snow thrower to rust.  
IMPORTANT: It is important to prevent gum deposits from  
forming in essential fuel system parts such as carburetor,  
fuel hose, or tank during storage. Also, alcohol blended  
fuels (called gasohol or using ethanol or methanol) can  
attract moisture which leads to separation and formation  
of acids during storage. Acidic gas can damage the fuel  
system of an engine while in storage.  
IMPORTANT: Never cover snow thrower while engine/ex-  
haust area is still warm.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
See appropriate section in manual unless directed to an authorized service center/department.  
PROBLEM  
CAUSE  
CORRECTION  
Does not start  
1. Fuel shut-off valve (if so  
equipped) in OFF position.  
2. Safety ignition key  
is not inserted.  
1. Turn fuel shut-off valve to OPEN position.  
2. Insert safety ignition key.  
3. Out of fuel.  
3. Fill fuel tank with fresh, clean gasoline.  
4. Move throttle to FAST position  
(or ON/OFF switch to ON position).  
5. Move to FULL position.  
6. Prime as instructed in the Operation section of this manual.  
7. Wait a few minutes before restarting, DO NOT prime.  
8. Connect wire to spark plug.  
4. Throttle in STOP position  
(or ON/OFF switch is OFF).  
5. Choke in OFF position.  
6. Primer not depressed.  
7. Engine is flooded.  
8. Spark plug wire is  
disconnected.  
9. Bad spark plug.  
10. Stale fuel.  
11. Water in fuel.  
9. Replace spark plug.  
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
Loss of power  
1. Spark plug wire loose.  
2. Throwing too much snow.  
3. Fuel tank cap is covered  
with ice or snow.  
1. Reconnect spark plug wire.  
2. Reduce speed and width of swath.  
3. Remove ice and snow on and around fuel tank cap.  
4. Dirty or clogged muffler.  
4. Clean or replace muffler.  
Engine idles or  
runs roughly  
1. Choke is in FULL position.  
2. Blockage in fuel line.  
3. Stale fuel.  
4. Water in fuel.  
5. Carburetor is in need of  
adjustment or overhaul.  
1. Move choke to OFF position.  
2. Clean fuel line.  
3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
5. Contact an authorized service center/department.  
Excessive  
vibration  
1. Loose parts or damaged  
augers or impeller.  
1. Tighten all fasteners. Replace damaged parts. If vibration  
remains, contact an authorized service center/department.  
Recoil starter  
is hard to pull  
1. Frozen recoil starter.  
1. See “IF RECOIL STARTER HAS FROZEN”  
in the Operation section of this manual.  
Loss of traction 1. Drive belt is worn.  
1. Check / replace drive belt.  
2. Check / reinstall drive belt.  
drive / slowing  
of drive speed  
2. Drive belt is off of pulley.  
3. Friction drive wheel is worn. 3. Contact an authorized service center/department.  
Loss of snow  
discharge or  
slowing of  
1. Auger belt is off of pulley.  
2. Auger belt is worn.  
3. Clogged discharge chute.  
1. Check / reinstall auger belt.  
2. Check / replace auger belt.  
3. Clean snow chute.  
4. Remove debris or foreign object from augers / impeller.  
snow discharge 4. Augers / impeller jammed.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
AUGER HOUSING / IMPELLER ASSEMBLY  
5
11  
6
11  
7
15  
16  
14  
11  
12  
8
4
13  
11  
17  
3
12  
1
10  
37  
9
9
2
9
37  
33  
32  
34  
30  
31  
31  
26  
36  
29  
20  
27  
21  
22  
28  
23  
23  
25  
24  
35  
22  
21  
2 (EXPLODED)  
18  
19  
01.07.026-D  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
AUGER HOUSING / IMPELLER ASSEMBLY  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
175321X431  
427148  
188909  
427146  
175322  
178675X431  
192199  
405400  
73800400  
74780426  
427942  
163183  
427145  
427154  
73900600  
180355  
194189  
407760  
427302  
427345  
407770  
407762  
174697  
407763  
407764  
189282  
407758  
174683  
427147  
7836M  
IMPELLER  
GEARBOX ASSEMBLY  
BEARING  
IMPELLER PULLEY  
DISCHARGE BASE  
CORNER BRACKET  
CLEAN OUT TOOL  
TOOL CLIP  
NUT 1/4-20  
SCREW 1/4-20 X .625  
NUT 5/16-18  
SCREW 5/16-18 X .625  
IMPELLER HUB  
IMPELLER SLEEVE  
NUT 3/8-16  
CARRIAGE BOLT  
SCREW 13-16 X .625  
PLUG  
GEARBOX COVER RH  
GASKET  
SEAL  
BEARING  
THRUST WASHER 1.00  
WORM GEAR  
AUGER SHAFT  
SQUARE KEY  
BEARING  
THRUST WASHER  
IMPELLER SHAFT  
ROLL PIN  
THRUST WASHER  
THRUST BEARING  
BEARING  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
174681  
174684  
407769  
407768  
407767  
427317  
192090  
O-RING  
SCREW 5/16-18 X .750  
GEARBOX COVER LH  
SHEAR BOLT  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
AUGER HOUSING / IMPELLER ASSEMBLY  
1
KEY  
PART  
NO.  
404930X505  
404933X431  
72270505  
155377  
NO.  
1
DESCRIPTION  
AUGER HOUSING  
SCRAPPER BAR  
CARRIAGEBOLT5/1618X.625  
NUT 5/1618  
2
3
4
3 (5x)  
4 (5x)  
2
01.07.003-A  
2
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
1
2
420497X431  
420498X431  
AUGER 30 LH  
AUGER 30 RH  
01.07.019-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
AUGER HOUSING / IMPELLER ASSEMBLY  
2
3
1
1
2
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
420478  
411939  
179582  
AUGER BEARING  
BEARING PLUG  
SCREW 5/1618 X 1.00  
3
01.07.024-B  
4
3
2
3
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
174762X431  
178777X431  
72270506  
751153  
SKID PLATE LH  
SKID PLATE RH  
CARRIAGE BOLT 5/1618 X .75  
NUT 5/1618  
4
1
01.11.001-B  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
CONTROL PANEL / DISCHARGE CHUTE  
5
7
15  
3
16  
*14  
*11  
2
4
*10  
6
6
*13  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
*12  
1
2
3
4
435023X505  
178633X505  
420673  
CHUTE WELDMENT  
DEFLECTOR WELDMENT  
DEFLECTOR CONTROL ASSEMBLY  
DEFLECTOR SEAL  
420325  
5
6
414280  
128415  
KNOB BLACK  
POP RIVET  
6
9
8
01.09.015-B  
7
8
9
*10  
*11  
*12  
*13  
*14  
15  
16  
17501010  
430324  
419822X431  
179829  
191730  
72250505  
751153  
184505  
420679  
420672  
SCREW 10-24 X .625  
CHUTE SNOW SHIELD  
SHIELD RETAINER STRAP  
SHOULDER BOLT 1/4-20 X .375  
NUT 1/4-20  
CARRIAGE BOLT 3/8-16 X .625  
NUT 5/16-18  
DEFLECTOR SPRING  
(SERVICE PART) DEFLECTOR CONTROL  
(SERVICE PART) DEFLECTOR CABLE BLACK  
NOTE:  
1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.  
2. ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
CONTROL PANEL / DISCHARGE CHUTE  
2
2
1
*3  
*7  
*6  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
*3  
*4  
*5  
*6  
*7  
428272  
17501010  
420678  
405932  
420675  
428273  
428310  
LEVER/CABLE ROTATOR ASSEMBLY  
SCREW 10-24 X .625  
ROTATOR HEAD  
ROTATOR PIVOT BRACKET  
PULLEY PIVOT  
CABLE ASSEMBLY ADJUSTABLE  
CABLE ASSEMBLY HEAT SHIELD  
*4  
01.09.010-B  
*5  
NOTES:  
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.  
2
01.15.009-A  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
421249  
74041024  
STEER CABLE  
SCREW 1024 X 1.50  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
HANDLES  
3
3
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
4
1
2
3
4
419798X431  
419799X431  
74780524  
751153  
LOOP HANDLE LH  
LOOP HANDLE RH  
SCREW 5/1618 X 1.50  
NUT 5/1618  
4
4
1
3
4
3
2
01.08.004-B  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
419797X431  
427513X431  
428867  
LOWER HANDLE  
2
PIVOT SUPPORT WELDMENT  
SCREW 5/1618 X .750  
SCREW 3/816 X 1.00  
17000616  
4
3
4
4
4
3
01-05-013-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
HANDLES  
2
10  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
10  
1
1
2
3
4
5
6
7
8
9
10  
180480  
405740  
180445  
187716  
180447  
178669  
180926  
72270505  
155377  
169675  
IMPELLER ROD  
TRACTION ROD  
3
SHIFTER ROD TOP  
SHIFTER ROD BOTTOM  
SPRING SLEEVE  
IMPELLER SPRING  
TRACTION SPRING  
CARRIAGE BOLT 5/16-18 X .625  
NUT 5/16-18  
8
9
4
RETAINER  
5
7
10  
5
6
01.12.001-E  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
HANDLES  
10  
2
11  
7
4
8
9
9
5
7
6
1
3
13  
8
12  
13  
14  
14  
12  
01.08.002-G  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
412683X431  
424517X431  
424516X431  
412679X008  
426918X008  
412677  
CONTROL PANEL  
CONTROL LEVER LH  
CONTROL LEVER RH  
TRACTION ROD ARM  
IMPELLER ROD ARM  
INTERLOCK BAIL  
SPACER  
421613  
8
9
10  
11  
12  
13  
14  
169675  
17060410  
414280  
414281  
178899  
19131316  
72120618  
RETAINER  
SCREW 1/4-20 X .62  
KNOB BLACK  
KNOB RED  
HANDLE KNOB  
WASHER 3/8  
CARRIAGE BOLT 3/8-16 X 2.25  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
HANDLES  
4
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
412675X431  
414572  
178831  
169675  
17060410  
421252X431  
INTERLOCK SPRING  
INTERLOCK CAM  
TORSION SPRING  
RETAINER  
SCREW 1/420 X .625  
INTERLOCK STOP  
3
2
5
1
01.08.007-B  
6
7
4
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
5
3
1
2
3
4
5
6
7
182906  
178668  
180927  
184471  
175262  
178770  
183784  
CONSOLE PANEL  
HEADLIGHT BEZEL  
FLOOD HEADLIGHT  
SHOULDERSCREW1024X.625  
SCREW 1024 X 1.25  
WIRE HARNESS  
2
1
4
BULB  
5
6
01.10.007-B  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
DRIVE  
42 EXPLODED  
46  
2
45  
48  
16  
14  
51  
17  
1
18  
47  
49  
15  
15  
50  
9
12  
11  
20  
22  
11  
53  
13  
24  
9
19  
9
23  
10  
11  
53  
52  
4
34  
8
53  
7
21  
6
24  
5
33  
23  
31  
53  
3
33  
38  
30  
29  
32  
28  
26  
53  
35  
27  
24  
26  
36  
4
23  
37  
42  
44  
43  
39  
53  
25  
24  
41  
40  
01.02.013-A  
39  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
DRIVE  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
1
198875  
SPEED SELECTOR  
ASSEMBLY  
SCREW 10-24 X .625  
END PLATE  
SCREW 5/16-18 X .50  
WASHER  
CONTROL ARM  
CLEVIS PIN  
SHIFTER PLATE  
SHOULDER BOLT  
SHIFTER BRACKET  
NUT 1/4-20  
CLUTCH PLATE  
CLUTCH BRACKET  
SHIFTER LINK  
RETAINER  
CONTROL SHAFT  
CLUTCH ROD  
RETAINER  
SHIFTER YOKE  
PIVOT ROD  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
179831  
175344  
178613  
74760514  
12000012  
402187  
401619  
417234  
401984X431  
180135  
402652  
428288  
184471  
410877  
413429X431  
402689  
414557  
178828  
402504  
401820  
198791  
402393  
17541008  
402511  
418894X431  
132010  
RUBBER RING  
BEARING  
WHEEL HUB  
SCREW 5/16-18-.875  
RETAINER RING  
SPROCKET SHAFT  
CHAIN  
SPROCKET WELDMENT  
SHIFTER BRACKET  
SPRING  
PLATE PIVOT ROD  
E-RING .375  
SHOULDER SCREW  
BOTTOM PAN  
SPRING BRACKET  
DRIVE PLATE ASSEMBLY  
IDLER SPRING  
IDLER SPRING  
PULLEY SHAFT  
DRIVE PLATE  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
17501010  
402685X505  
17490508  
57079  
405485  
198580  
403097X008  
402881  
403096X431  
191730  
402856X008  
416717X431  
187101  
700279  
427542  
402568  
169675  
401732  
402310  
12000036  
402878  
751153  
BEARING  
PULLEY HALF  
SCREW 10-24 X .50  
SPACER BEARING  
SWING PLATE  
NUT 3/8-16  
SCREW 5/16-18 X .750  
RETAINER  
RETURN SPRING  
NUT 5/16-18  
BEARING  
NUT 5/16-18  
408981  
73930500  
198176X431  
RUBBER WHEEL PLATE  
428867  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
DRIVE  
6
7
1b  
4
8
3
1b  
7
1a  
2
3
5
4
01.03.002-A  
6
KEY  
PART  
NO.  
NO.  
DESCRIPTION  
1
404923  
404307  
9456M1  
402691  
174697  
179830  
146315  
17490508  
155443  
189282  
AXLE ASSEMBLY (assy of 1a,1b)  
AXLE SHAFT  
ROLL PIN 3/16 X 1.50  
SPROCKET  
THRUST WASHER  
BEARING  
SCREW 5/1618 X .625  
SCREW 5/1618 X .500  
KLIK PIN 1/4 X 1.50  
SQUARE KEY  
1a  
1b  
2
3
4
5
6
7
8
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
CHASSIS / ENGINE / PULLEYS  
2
3
2
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
3
- -  
- - - - - -  
B&S ENGINE MODEL  
15C114-1465-E8  
FRAME  
BOLT 3/8-16  
SCREW 5/16-18 X .750  
1
2
3
418694X505  
150406  
428867  
1
01.00.034-A  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
436146X505  
ENGINE MOUNT PLATE  
01.01.007-B  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
CHASSIS / ENGINE / PULLEYS  
KEY  
NO.  
PART  
NO.  
23  
22  
DESCRIPTION  
14  
24  
11  
1
2
408007  
419744  
IMPELLER BELT  
TRACTION BELT  
21  
20  
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
423723X431  
180523  
426589  
74780524  
423990X431  
428867  
424297  
751153  
187786  
180522  
74780520  
59289  
73800500  
851084  
400026  
426491  
IDLER ARM BRACKET  
IDLER PULLEY  
NUT 5/16-18  
SCREW 5/16-18 X 1 .50  
IDLER BRACKET  
SCREW 5/16-18 X .625  
SHOULDERBOLT5/16-18X.500  
NUT 5/16-18 NYLOCK  
TRACTION IDLER ARM  
TRACTION PULLEY  
SCREW 5/16-18 X 1 .00  
WASHER  
NUT 5/16-18  
SCREW 3/8-24 X 1.375  
WASHER  
PULLEY ENG IMPELLER  
PULLEY ENG TRACTION  
SCREW 5/16-18 X 1 .00  
LOCKWASHER 5/16  
BELT GUIDE  
LOCKWASHER 5/16  
IDLER BUSHING  
14  
19  
21  
20  
13  
18  
17  
12  
16  
14  
15  
6
7
10  
5
4
8
3
9
426490  
1
74610516  
10040500  
155452  
11050500  
175331  
2
01.21.003-C  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
428684  
COVER ASSEMBLY  
01.21.013-B  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
WHEELS  
2
2
17  
3
1
23  
4
20  
16  
15  
24  
19  
22  
5
6
7
17  
21  
18  
8
9
16  
10  
11  
20  
21  
23  
22  
19  
12  
14  
KEY  
NO.  
1
PART  
NO.  
405161  
184471  
12000045  
192126  
13  
13  
DESCRIPTION  
COVER  
11  
10  
14  
12  
9
8
2
3
4
SHOULDER SCREW  
RETAINER RING  
WHEEL DRIVER  
RETAINER RING  
WHEEL LOBE  
CLUTCH SLIDE  
SPRING  
2
7
6
5
4
3
5
6
7
8
182466  
187622  
194941  
179139  
189282  
194940  
174697  
193506X431  
179148X431  
17490508  
194943X008  
194944X008  
181847  
17600406  
405077  
700279  
85179  
193885  
182015  
194939X008  
1
01.15.001-B  
2
9
SQUARE KEY  
AXLE LOBE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
THRUST WASHER  
STEERING YOKE  
STEERING BRACKET  
SCREW 5/1618 X .50  
PIVOT BRACKET  
BELLCRANK  
BELLCRANK PIN  
SCREW 1/420 X .375  
STEERING LINK  
RETAINER  
RETAINER  
SPRING  
LEVER PIN  
PIVOT BRACKET  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
410293  
410294  
17490408  
17600406  
CABLE BRACKET LH  
CABLE BRACKET RH  
SCREW 1/4-20 X .500  
SCREW 1/4-20 X .375  
3
4
1
2
01.15.003-C  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
WHEELS  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
432337X428  
432338X428  
WHEEL ASSEMBLY LH  
WHEEL ASSEMBLY RH  
1
2
01.06.015-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
BAG OF PARTS  
KEY  
NO.  
1
2
3
4
5
6
PART  
NO.  
198563  
169675  
180684X008  
184505  
DESCRIPTION  
POWER CORD  
RETAINER PIN  
WRENCH  
REMOTE SPRING  
SHOULDER BOLT 1/4-20  
LOCKNUT 1/4-20  
4
6
5
8
7
179829  
191730  
3
7
8
9
10  
11  
12  
72250505  
751153  
73800600  
19131316  
192090  
CARRIAGE BOLT 5/16-18 X 5/8  
LOCKNUT 5/16-18  
LOCKNUT 3/8-16  
WASHER 3/8  
SHEAR BOLT 1/4-20 X 1-13/16  
LOCKNUT 1/4-20  
10  
9
73800400  
2
12  
1
11  
01.14.003-B  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
193071  
SAFETY IGNITION KEY  
1
01.14.007-A  
1
3
2
4
1
4
2
01.14.012-A  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
180445  
187716  
72270505  
155377  
SHIFTER ROD TOP  
SHIFTER ROD BOTTOM  
CARRIAGE BOLT 5/16-18 X .75  
NUT 5/16-18  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
BAG OF PARTS  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
435840  
KIT HARNESS CONN B&S  
01.14.016-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL XT11530ES (96192003503)  
DECALS  
1
9
4
6
10  
3
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
3
4
6
181037  
181035  
181042  
181033  
429591  
429590  
437970  
437971  
DECAL, DANGER  
DECAL, DANGER, DEFLECTOR  
DECAL, DANGER  
DECAL, INSTRUC.  
9
DECAL, CONS RT SPD/LEV/PWRST  
DECAL, CONS LT DEF/LEV/PWRST  
OWNER’S MANUAL, ENGLISH  
OWNER’S MANUAL, FRENCH  
10  
- -  
- -  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects  
in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer pur-  
chaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part  
which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations  
and exclusions.  
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-  
facturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the  
purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by  
the purchaser unless such return is requested by the manufacturer.  
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date  
of original purchase.  
4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained  
in accordance with the instructions furnished. This Warranty does not apply to any product which has been sub-  
jected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the  
product.  
5. Exclusions: Excluded from this Warranty are belts, shear pins, normal wear, normal adjustments, standard hard-  
ware and normal maintenance.  
6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Poulan Pro  
Poulan, Customer Service Department  
Customer Service Department  
5855 Terry Fox Way  
1030 Stevens Creek Road  
Mississauga, Ontario  
Augusta, GA 30907 USA  
L5V 3E4  
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the  
authorized dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED  
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-  
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied  
Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific  
legal rights, and you may have other rights which vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Security Camera C1988M B User Manual
Pentax Digital Camera Optio S5n User Manual
Philips Camera Accessories TC8277 User Manual
Philips DVR RT 567 User Manual
Philips TV Mount SQM5322 User Manual
Philips Universal Remote SBC RU 220 User Manual
Philips VCR VRC202MG User Manual
Poulan Chainsaw PP3516AVX User Manual
Poulan Snow Blower 406275 User Manual
Prince Castle Outdoor Timer 755 HM10 User Manual